Twist Drill — Extra Long HSS‑G, 10.5 mm, 135° Tip (Bright Finished) A Twist Drill in an extra long execution for deep metal drilling, designed for use with a Drilling Machine and optimised for precise work in hard materials. Extra-long design for deep drilling HSS‑G material for precise metal drilling 135° tip for hard materials like stainless steel Fully ground shank for high runout accuracy DIN 1869 standard for industrial use Faster deep drilling with reliable cutting performance The MetavCUT Extra Long Twist Drill combines HSS‑G material and an elongated geometry to deliver efficient deep-hole performance. Thanks to CNC grinding of the flutes, this design achieves up to 40% faster drilling and requires around 50% less feed force compared with conventional HSS bits, which directly reduces operator effort and machine load. The 10.5 mm diameter and overall length of 430 mm with a spiral length of 295 mm make this tool especially suitable when deep bore depths or difficult access require an extended reach. Precise holes and consistent centring for demanding work A fully ground shank and precise flute geometry yield very sharp cutting edges and high concentricity, resulting in clean, accurate bores even in tough materials. The 135° tip reduces the tendency to wander when starting a hole and shortens the initial penetration time on harder steels and stainless grades. For operators unfamiliar with ground versus rolled drills: ground (HSS‑G) tools have flutes formed by grinding, not rolling, which produces higher sharpness and runout accuracy but requires careful handling and, ideally, cooling during use. Designed for metalworking professionals and industrial applications This Twist Drill is intended for metalworking tasks such as drilling in legated and unlegated steel, cast iron, sintered iron and certain hard plastics. Conforming to DIN 1869, the tool is engineered for industrial environments where repeatable, deep drilling is required. Use with stationary or robust handheld Drilling Machines is recommended; portable applications should ensure adequate support and cooling to avoid breakage. The bright finished surface supports chip evacuation and visual inspection of wear. Practical handling and operational advice for longer tool life To achieve the best results with an extra long HSS‑G Twist Drill, secure the workpiece well and use appropriate coolant or lubricant to manage heat in deep bores. Reduced feed forces, as enabled by the ground geometry, decrease radial stress on the bit, but the extended length increases bending risk, so avoid excessive lateral loads. If drilling wood, a metal twist drill can be used but will offer less guidance and a rougher finish than purpose-made wood bits; sharpening and regrinding are straightforward advantages of HSS tools. Strong recommendation: For professional deep-metal drilling choose the MetavCUT Extra Long Twist Drill (HSS‑G) and consult METAV Werkzeuge for tailored technical advice — Email: info@metav-werkzeuge.com — Phone: +49 2822 7131930 — WhatsApp: +49 170 2837271 Twist Drill Brand: MetavCUT SKU: 34105-FDA Diameter: 10.5 mm Total length: 430 mm Spiral length: 295 mm Tip angle: 135° Material: HSS‑G Standard: DIN 1869 Execution / Type: Extra Long Shank execution: Fully ground Colour / Finish: Bright finished Intended machine: Drilling Machine Application: Drills for metal Model series: Standard Line Packaging unit: 10 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill used for and which materials suit it best? The Twist Drill by MetavCUT is primarily used for drilling in metal; it performs especially well on legated and unlegated steel, cast iron and certain hard plastics. Its extra long design is intended for deep holes and for situations where extended reach is required. Which three main drill types exist? The main categories are metal drills, wood drills, and masonry/concrete drills. The MetavCUT Twist Drill belongs to the metal drill group and is optimised for metalworking tasks.

Twist Drill — 10 mm · 135° · Extra Long · HSS‑G · DIN 1869 · Bright Finished · Fully Ground Shank (Drill for Metal) by MetavCUT The Twist Drill is an extra‑long HSS‑G metal drilling bit designed for deep, precise holes in demanding machining applications with a 10 mm diameter and 135° tip angle. Extra‑long design for deep drilling 135° tip for hard materials and better centering HSS‑G ground geometry for faster drilling Fully ground shank for high concentricity DIN 1869 compliant for industrial reliability Engineered for deep, precise metal drilling with confidence The Twist Drill from MetavCUT offers an extra long overall length of 430 mm with a spiral length of 295 mm, specifically intended for deep hole operations where reach and stability matter. The combination of HSS‑G material and a fully ground shank yields high roundness accuracy and clean hole surfaces, which reduces rework and improves assembly tolerances. Designed for use in a Drilling Machine, this long‑reach bit maintains rigidity despite its length, making it suitable for workshop and production environments that require repeatable, centered holes. Faster cutting and lower operator effort through ground geometry Thanks to the CNC ground geometry of the HSS‑G blank, this Twist Drill can achieve up to 40% faster cutting while requiring approximately 50% less thrust compared with conventional rolled HSS drills. The 135° tip angle is optimized for harder materials such as stainless steel and alloyed steels, reducing initial burr formation and shortening pilot times. Grinding the flutes produces very sharp cutting edges and a precise helix, which improves chip evacuation and lowers the risk of chatter when used with appropriate machine settings and coolant. Best applications, handling tips and material guidance This extra‑long Twist Drill is primarily intended for Drilling for Metal: alloyed and unalloyed steel, cast iron, sintered materials, and non‑ferrous metals, as well as technical plastics where a robust bit is required. For deep hole work, use steady support and consistent coolant flow to dissipate heat and avoid premature wear or fracturing; ground HSS drills are sharper but can be less ductile than rolled equivalents, so stationary setups and controlled feeds are recommended. The geometry and DIN 1869 specification make the bit particularly effective for through and deep blind holes up to practical limits determined by machine rigidity. Precision advantages and what makes this drill stand out MetavCUT’s Standard Line Twist Drill distinguishes itself by pairing bright finished surfaces with a geschliffen / fully ground flute profile, resulting in excellent runout performance and reliable centering, especially in demanding metalworking tasks. The design reduces the tendency for the tip to wander on entry, and when combined with the correct pilot technique and coolant, delivers consistent hole quality that supports downstream processes such as thread tapping and press fits. Strong recommendation: For demanding deep‑hole metalworking tasks, the MetavCUT Twist Drill (10 mm, extra long, HSS‑G, 135°) is highly recommended — for expert selection, technical advice or to confirm suitability for specific materials and machines, contact METAV Werkzeuge: info@metav-werkzeuge.com · +49 2822 7131930 · WhatsApp +49 170 2837271 Technical specifications for planning and procurement Bezeichnung: Twist Drill Marke: MetavCUT SKU: 34100-FDA Durchmesser: 10 mm Spitzenwinkel: 135° Ausführung: extra long Gesamtlänge: 430 mm Spirallänge: 295 mm Material: HSS‑G Schaft Ausführung: fully ground Farbe: bright finished Für Bohrmaschine: Drilling Machine Anwendung: Drills for metal Modellserie: Standard Line Norm: DIN 1869 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill best used for? The MetavCUT Twist Drill (Drill for Metal) is mainly used for machining high‑strength materials and larger diameters where deep holes are required; its extra‑long design and HSS‑G construction make it suitable for alloyed and unalloyed steels, cast irons and hard plastics under machine and coolant support. Can the MetavCUT Twist Drill be used in a handheld drill? While the Twist Drill is designed for use in a Drilling Machine for optimal stability, it can be used in powerful handheld machines for certain tasks; however, for safety and the best results with an extra‑long HSS‑G bit, a stationary machine and coolant are recommended. For what is a Twist Drill used? A Twist Drill is primarily applied when working on high‑strength materials and larger drill diameters. Its shape allows easy resharpening and it withstands higher loads; this makes the bit suitable for deep holes and demanding metalworking tasks. Which three drill types exist? Typical categories are metal drills, wood drills and stone/concrete drills. Why are Twist Drills resharpened at the tip? Resharpening reduces the cross‑edge at the drill tip, lowering friction so smaller feed forces are needed; this improves centering and reduces required thrust for the Twist Drill. Can a Twist Drill be used for wood? A metal Twist Drill can be used in wood but will usually offer poorer guidance and a rougher finish; it is easier to resharpen and shows less self‑feed than dedicated wood drills. For which drilling depths is the Twist Drill most used? A solid hole is commonly made with a Twist Drill. For diameters up to 20 mm and drill depths up to about 100 mm, the Twist Drill is the most frequently used tool. What is better, HSS or HSSE? The general belief that HSSE steels are always superior to HSS is not universally correct; consider the working conditions carefully to determine whether the higher cost of HSSE is justified.

Die extra lange Ausführung kombiniert HSS-G Schleiftechnik, 135° Spitzenwinkel und eine Spirallänge 310 mm zu einer Lösung für tiefe, präzise Metallbohrungen; die robuste Konstruktion ermöglicht effizientes Bohren in legierten und unlegierten Stählen. Bestellen Sie den Spiralbohrer von MetavCUT direkt über Metav oder fordern Sie bei Bedarf die technische Beratung an. Spiralbohrer – extra lang HSS-G für Metall Der Spiralbohrer in extra langer Ausführung ist für tiefe Metallbohrungen konzipiert und eignet sich besonders für legierte Stähle, Gusswerkstoffe und Hartkunststoffe. Geschliffenes HSS-G für hohe Präzision Extra lange Gesamtlänge 455 mm Spirallänge 310 mm für tiefe Löcher 135° Spitzenwinkel für harte Werkstoffe DIN 1869 Tieflochspirale für Metall Sicheres Tiefbohren mit hoher Präzision Die geschliffene HSS-G Geometrie bietet scharfe Schneidkanten und hohe Rundlaufgenauigkeit, was saubere Bohrlöcher in harten Werkstoffen ermöglicht. Durch den 135° Spitzenwinkel reduziert sich die Anbohrzeit bei Edelstahl oder temperharten Stählen, während die extra lange Gesamtlänge die Erreichbarkeit tiefer Stellen verbessert. Dieser Bohrer arbeitet effizienter als walzgeformte Varianten und eignet sich daher für anspruchsvolle Metallbearbeitung. Geeignete Anwendungen und Materialkompatibilität Für den Einsatz in legierten und unlegierten Stählen, Grauguss, Gusseisen, Sintereisen, Temperguss sowie Nichteisenmetallen ist die Kombination aus DIN 1869 Tieflochspirale und geschliffenem Schaft ideal. Die Tiefe der Bohrungen wird durch die Spirallänge 310 mm unterstützt, wodurch tiefere Sacklöcher und schwer zugängliche Bereiche zuverlässig erreicht werden. Bei besonders zähen Werkstoffen empfiehlt sich ergänzende Kühlung und stationäre Maschinenaufnahme. Bedienungshinweise und Maschinenempfehlung Der Bohrer wurde für den Einsatz an stationären und handgeführten Maschinen konzipiert; für Handbohrmaschinen ist die robuste Ausführung geeignet, jedoch sollte auf geeignete Kühlung und stabile Spannaufnahme geachtet werden. Durch die geschliffene Schaft-Ausführung ergeben sich sehr gute Rundlaufwerte, weshalb langsame Vorschübe und konstante Kühlung die Standzeit erhöhen. Bei tiefen Bohrungen ist schrittweises Aufbohren zur Entlastung der Querschneide zu empfehlen. Zielgruppe, Vorteile und Einsatznutzen Entwickelt für Werkstätten, Instandhaltung und Metallverarbeitung, bietet diese Ausführung klare Vorteile für Anwender, die tiefe Bohrungen präzise und wiederholbar benötigen. Die extra lange Konstruktion reduziert Rüstzeiten bei tiefen Bohrungen und minimiert das Nacharbeiten. MetavCUT setzt mit dieser Lösung auf Praktikabilität und Präzision, sodass Qualitätsansprüche in Serien- und Einzelbetrieb erfüllt werden. Mit dem MetavCUT HSS-G Spiralbohrer extra lang über Metav die passende Tiefbohrlösung sichern und bei Fragen die technische Beratung per E‑Mail info@metav-werkzeuge.com kontaktieren Produktmerkmale Bezeichnung: Spiralbohrer Artikelnummer: 34115-FDA Marke: MetavCUT Serie: Standard Line Daten Durchmesser: 11,5 mm Gesamtlänge: 455 mm Spirallänge: 310 mm Spitzenwinkel: 135° Verpackungseinheit: 10 Besonderheiten Material: HSS-G Norm: DIN 1869 Schaft-Ausführung: geschliffen Ausführung: extra lang Für Bohrmaschine: Handbohrmaschine Farbe: blank Anwendung: Bohrer für Metall FAQ Für welche Werkstoffe eignet sich der Bohrer am besten? Der MetavCUT Spiralbohrer (Standard Line, SKU 34115-FDA) eignet sich besonders für legierte und unlegierte Stähle, Grauguss, Gusseisen sowie Nichteisenmetalle und Hartkunststoff. Ist die extra lange Ausführung für Handbohrmaschinen geeignet? Ja, die Ausführung ist für Handbohrmaschine geeignet, wobei bei tiefen Bohrungen stabile Spannaufnahme und Kühlung empfohlen werden, um Bruchrisiken zu minimieren. Wie beeinflusst der 135° Spitzenwinkel die Bohrleistung? Der 135° Spitzenwinkel reduziert die Anbohrzeit in härteren Werkstoffen und verbessert das Zentrierverhalten, wodurch das Bohren in zähen Metallen effizienter wird. Benötigt der geschliffene Bohrer spezielle Kühlung oder Aufnahme? Geschliffene HSS-G Bohrer profitieren von konstanter Kühlung und einer stabilen Aufnahme, besonders bei tiefen Bohrungen, um Standzeit und Schneidkanten zu schonen. Welche Tiefe ist mit diesem Bohrer realistisch zu erreichen? Dank der Spirallänge von 310 mm und der Gesamtlänge von 455 mm lassen sich deutlich tiefere Löcher als mit Standardbohrern realisieren; bei sehr tiefen Durchmessern empfiehlt sich stufenweises Aufbohren.

Kompakte Empfehlung: Der MetavCUT HSS-G Spiralbohrer vereint extra langes Design, Spirallänge 310 mm und 135° Spitzenwinkel für präzise Tiefbohrungen in legierten und unlegierten Stahl; für anspruchsvolle Anwendungen empfiehlt sich Kühlung und stationäre Aufnahme bei längeren Serien. Spiralbohrer »34110-FDA« von MetavCUT – HSS-G extra lang Der Spiralbohrer von MetavCUT ist ein HSS-G geschliffenes Werkzeug für Tiefbohrungen in Stahl, Guss und Hartkunststoff, entwickelt für Werkstatt und Produktion. HSS-G geschliffen für präzise Metallbohrungen Extra lang: Gesamtlänge 455 mm, Spirallänge 310 mm Spitzenwinkel 135° für harte Werkstoffe Geeignet für Handbohrmaschine und stationäre Geräte DIN 1869 Tieflochspirale für extra tiefe Löcher Lange Reichweite für kontrollierte Tiefbohrungen und besseren Arbeitseinsatz Das extra lang ausgelegte Bohrwerkzeug mit Gesamtlänge 455 mm und Spirallänge 310 mm ermöglicht das Erreichen tiefer Bohrpunkte ohne ständiges Nachsetzen oder Verlängern. Bei tiefen Bohrungen reduziert die längere Spirale das Risiko von Späneverstopfung, weil die Späne über die längere Spirallänge sicher abgeführt werden. Der direkte Nutzen ist weniger Maschinenstillstand und höhere Effizienz bei Bauteilen mit schwer zugänglichen Bohrpunkten. Geschliffene HSS-G-Geometrie für saubere Bohrbilder und geringeren Kraftaufwand Die HSS-G Materialkombination und der CNC-Schliff sorgen für sehr scharfe Schneiden und hohe Rundlaufgenauigkeit, wodurch sich das Bohren spürbar erleichtert. Gemäß Herstellerangaben kann die geschliffene Geometrie den Vorschubaufwand reduzieren und die Bohrzeit verkürzen; das Resultat sind sauberere Bohrlöcher und weniger Nacharbeit beim Entgraten. Für länger andauernde Nutzung empfiehlt sich die Anwendung von Kühlmittel, um Verschleiß zu minimieren. Passgenau für Werkstattmaschinen und typische Metallanwendungen Mit einem Durchmesser von 11 mm fällt das Werkzeug in den Standard-Bereich und eignet sich somit für den Alltagsgebrauch in Werkstatt und Produktion. Die DIN 1869 konforme Tieflochspirale macht das Werkzeug besonders geeignet für legierten und unlegierten Stahl, Gusseisen und Hartkunststoff. Für empfindliche Präzisionsbohrungen empfiehlt sich Vorzentrierung mit einem Zentrierbohrer, um Abweichungen beim Anbohren zu vermeiden und die Standzeit zu erhöhen. Sicherheitsempfehlungen, Einsatzhinweise und Pflege für lange Lebensdauer Weil geschliffene Werkzeuge empfindlicher sein können, entsteht die beste Kombination aus Standzeit und Ergebnis durch kontrollierte Schnittbedingungen: passende Drehzahl, moderater Vorschub und kontinuierliche Kühlung. Spannfutter sicher fixieren und Werkstück fest spannen, um Rundlauffehler zu vermeiden. Regelmäßige Kontrolle der Schneiden und rechtzeitiges Nachschleifen oder Austausch reduzieren Bruchrisiko und erhöhen Prozesssicherheit. MetavCUT empfiehlt das HSS-G Spiralbohrer als Lösung für präzise, tiefe Bohrungen; bei technischen Fragen stehen die Ansprechpartner von Metav per eMail info@metav-werkzeuge.com und Telefon +49 2822 7131930 zur Verfügung. Produktmerkmale Artikelnummer: 34110-FDA Marke: MetavCUT Bezeichnung: Spiralbohrer Serie / Baureihe / Ausführung: Standard Line / extra lang Fakten Gesamtlänge: 455 mm Spirallänge: 310 mm Durchmesser: 11 mm Spitzenwinkel: 135° Verpackungseinheit: 10 Besonderheiten Material: HSS-G (geschliffen, hohe Schärfe, präzise) Norm: DIN 1869 Schaftausführung: geschliffen Farbe: blank Für Bohrmaschine: Handbohrmaschine FAQ Welche Materialien lassen sich mit dem MetavCUT HSS-G Spiralbohrer bearbeiten? Der MetavCUT HSS-G Spiralbohrer ist ausgelegt für legierten und unlegierten Stahl, Gussstahl, Gusseisen, Sintereisen, Temperguss, Nichteisenmetalle und Hartkunststoff; die geschliffene Geometrie sorgt für saubere Bohrbilder auch in härteren Werkstoffen. Ist der Spiralbohrer für Handgeführte Maschinen geeignet? Ja, der Spiralbohrer mit 11 mm Durchmesser eignet sich für Handbohrmaschine im Standardbereich, wobei bei tiefen Bohrungen und längeren Einsatzzeiten die Nutzung stationärer Aufnahmen und Kühlung empfohlen wird. Warum ist der Spitzenwinkel 135° wichtig? Der 135° Spitzenwinkel reduziert den Anbohrwiderstand bei harten Werkstoffen und verringert das Abweichen beim Anbohren, was bei der DIN 1869 Tieflochspirale zu stabileren Ergebnissen führt. Wie beeinflusst die geschliffene Ausführung die Nutzung? Geschliffene HSS-G Werkzeuge bieten sehr scharfe Kanten und hohe Rundlaufgenauigkeit, sind aber etwas empfindlicher; dadurch sind sie ideal für präzise Metallbearbeitung, erfordern aber kontrollierte Schnittbedingungen und Kühlung. Welche Informationen liefert die Artikelnummer 34110-FDA beim Bestellen? Die Artikelnummer 34110-FDA identifiziert exakt das MetavCUT HSS-G Spiralbohrer Modell aus der Standard Line mit den angegebenen Abmessungen und der extra langen Ausführung.

Die Kombination aus HSS‑G‑Schliff, extra langer Gesamtlänge und 135° Spitzenwinkel ermöglicht schnelle, kraftsparende Tiefbohrungen in Stahl und Gusswerkstoffen; profitieren Sie von bis zu 40 % schnellerem Bohren und deutlich reduzierter Anpresskraft. Bestellen Sie den Bohrer direkt bei Metav Werkzeuge oder fragen Sie unsere technische Beratung per eMail oder Telefon an. Spiralbohrer 12,5 mm (HSS‑G, extra lang) von MetavCUT Der Spiralbohrer ist eine extra lange, geschliffene HSS‑G Ausführung zum Bohren tiefer Löcher in legierten und unlegierten Stahl sowie Gusswerkstoffe. HSS‑G geschliffen für präzise Metallbohrungen Extra lange Ausführung mit 480 mm Gesamtlänge Spirallänge 330 mm für tiefe Bohrungen Spitzenwinkel 135° für harte Werkstoffe DIN 1869 Norm, geeignet für Handbohrmaschine Schnelleres Bohren bei reduzierter Anpresskraft für mehr Effizienz Dank des HSS‑G CNC‑Schliffs dringt der Bohrer leichter in harte Werkstoffe ein, wodurch sich die Bohrrate erhöhen lässt. Durch den schliffbedingten Spanwinkel reduziert sich die notwendige Anpresskraft um bis zu 50 %, was Arbeitszyklen verkürzt und die Ermüdung bei manuellen Bohrungsarbeiten verringert. Dieser Vorteil führt direkt zu höheren Stückzahlen pro Schicht und geringeren Ausfallzeiten. Tiefe Bohrungen sicher ausführen mit Tieflochspirale Für Anwendungen, bei denen das Bohrloch tief sein muss, sorgt die Tieflochspirale für effizienten Spantransport und saubere Bohrlöcher. Die extra lange Ausführung mit 480 mm Gesamtlänge und 330 mm Spirallänge ermöglicht Zugänge, die Standardbohrer nicht erreichen. So lassen sich tiefe Sacklöcher und schwer zugängliche Bereiche ohne mehrfaches Nacharbeiten bearbeiten. Materialvielfalt bearbeiten und Werkstoffe schonen Dieser Bohrer wurde für Grauguss, Gusseisen, legierten und unlegierten Stahl sowie Hartkunststoffe entwickelt und ist damit vielseitig einsetzbar. Der 135° Spitzenwinkel verkürzt die Anbohrzeit bei härteren Werkstoffen und reduziert das Mitlaufen auf der Oberfläche, was die Maßhaltigkeit des Bohrlochs verbessert. Dadurch entsteht ein direkter Nutzen in Form von passgenaueren Bauteilen und weniger Nacharbeit. Fertigungsqualität und Handhabungshinweise für lange Standzeiten Die geschliffene Schaftausführung und der präzise CNC‑Schliff gewährleisten hohe Rundlaufgenauigkeit und scharfe Schneidenkanten, die saubere Bohrbilder liefern. Bei stationärem Einsatz empfiehlt sich eine Kühlschmierstoffzufuhr, da geschliffene HSS‑Bohrer empfindlicher gegenüber Kerbwirkung sein können; ruhiger Anlauf und kontrollierter Vorschub verlängern die Standzeit spürbar. MetavCUT empfiehlt die extra lange HSS‑G Ausführung für anspruchsvolle Tiefbohrungen — Bestellwunsch oder technische Klärung per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 möglich Produktmerkmale Artikelnummer: 34125-FDA Marke: MetavCUT Bezeichnung: Spiralbohrer Modellserie: Standard Line Norm: DIN 1869 Material: HSS-G Ausführung: extra lang Schaftausführung: geschliffen Farbe: blank Für_Bohrmaschine: Handbohrmaschine Verpackungseinheit: 10 Fakten Durchmesser: 12,5 mm Gesamtlänge: 480 mm Spirallänge: 330 mm Spitzenwinkel: 135° Verpackungseinheit: 10 Besonderheiten Tieflochspirale Geschliffener HSS‑G Schliff für hohe Präzision Geeignet für legierten und unlegierten Stahl Geeignet für Gussstahl und Gusseisen geeignet für Sintereisen und Temperguss geeignet für Nichteisenmetalle und Hartkunststoff FAQ Wie tief kann ich mit diesem Bohrer sicher bohren? Der Spiralbohrer von MetavCUT (Spiralbohrer, SKU 34125-FDA) ist als extra lange Ausführung mit 330 mm Spirallänge konzipiert und eignet sich für tiefe Bohrungen; bei sehr tiefen Sacklöchern empfiehlt sich der schrittweise Spanabtrag und Kühlung, um Spanstauungen zu vermeiden. Für welche Werkstoffe ist der HSS‑G Spiralbohrer geeignet? Der Spiralbohrer MetavCUT Standard Line in HSS‑G Ausführung eignet sich für legierten und unlegierten Stahl, Gussstahl, Gusseisen sowie für Hartkunststoffe und Nichteisenmetalle; der 135° Spitzenwinkel ist speziell für härtere Werkstoffe vorteilhaft. Kann der Bohrer mit einer Handbohrmaschine verwendet werden? Ja, der Spiralbohrer ist für den Einsatz in Handbohrmaschinen vorgesehen, allerdings sollte die Maschine ausreichend Leistung bieten und ein ruhiger Vorschub sowie gegebenenfalls Kühlschmierstoff eingesetzt werden, um Bruchrisiken bei geschliffenen Schneiden zu minimieren. Welche Pflege verlängert die Standzeit des Bohrers? Um die Standzeit des Spiralbohrers MetavCUT (SKU 34125-FDA) zu erhöhen, empfiehlt sich kontrollierter Vorschub, Verwendung von Kühlschmierstoff bei Stahlbearbeitung und das Vermeiden von seitlichen Belastungen beim Bohren, insbesondere bei sehr langen Ausführungen.

Twist Drill — Twist Drill, 12 mm, 135°, Extra Long, Bright Finished, Fully Ground, DIN 1869, HSS‑G (MetavCUT) The Twist Drill is an extra long HSS‑G metal drill designed for deep, precise holes in demanding materials such as alloyed and unalloyed steel. Twist Drill 12 mm diameter for deep holes Extra long design for deep and hard-to-reach holes 135° point angle suited for harder materials HSS‑G fully ground for precise metal drilling DIN 1869 standard with 480 mm overall length Engineered for deep, consistent metal drilling with reduced effort The extra long geometry of this Twist Drill combines a 480 mm overall length with a 330 mm spiral length, making the bit particularly suited for applications where reach is critical. The 12 mm diameter maintains stability while permitting access into recessed or hard‑to‑reach positions. Designed for use on a Drilling Machine, the tool’s construction allows straightforward integration into workshop routines and industrial tasks where deep, straight bores are required. Faster feeds and cleaner holes thanks to fully ground HSS‑G construction A Fully Ground HSS‑G designation means the flute geometry is manufactured by CNC grinding rather than rolling, resulting in sharp cutting edges and high concentricity. This produces noticeably cleaner holes and precise guidance in metals. With a 135° point angle, the bit reduces initial deflection on harder materials; the grinding and geometry together enable up to 40% faster drilling and can require 50% less feed force compared with conventional HSS variants under comparable conditions, improving efficiency for repetitive metalworking tasks. Suitable applications and careful usage recommendations This tool is intended for metal drilling and performs best in alloyed and unalloyed steel, cast steel, cast iron, sintered iron, tempered cast materials, non‑ferrous metals and hard plastics. Because HSS‑G items can be more brittle than rolled types, the bit is particularly appropriate for stationary setups or when good coolant and stable clamping are available. For portable hand‑held drilling, ensure secure workholding and appropriate cooling to minimise risk and extend service life. Practical advantages for workshops and maintenance departments The combination of reach and precision makes this bit valuable for maintenance, toolroom, and fabrication tasks where access is constrained. The bright finished surface eases chip evacuation visibility and inspection, while the DIN 1869 conformity signals suitability for deeper drilling operations under more demanding conditions. Opting for a fully ground HSS variant provides benefits in hole quality and repeatability when machining harder or alloyed materials. We recommend the MetavCUT Twist Drill for deep, high‑precision metal drilling — for technical questions or personalised advice METAV Werkzeuge provides comprehensive support via info@metav-werkzeuge.com, phone +49 2822 7131930 or WhatsApp +49 170 2837271 Technical information Designation: Twist Drill Brand: MetavCUT SKU: 34120-FDA Diameter: 12 mm Point angle: 135° Execution: Extra long Colour: Bright finished Total length: 480 mm Spiral length: 330 mm Shank execution: Fully ground Material: HSS‑G Standard: DIN 1869 For drilling machine: Drilling Machine Model series: Standard Line Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ How deep can the MetavCUT Twist Drill reach? The MetavCUT Twist Drill is designed for deep drilling tasks thanks to its extra long geometry: a total length of 480 mm and a spiral length of 330 mm provide extended reach for recessed bores and hard‑to‑access positions on a Drilling Machine. Which materials is the MetavCUT Twist Drill suitable for? The MetavCUT Twist Drill in HSS‑G is suitable for alloyed and unalloyed Steel, Cast Steel, Cast Iron, Sintered Iron, Tempered Cast materials, Non‑ferrous Metals and Hard Plastics, delivering precise, repeatable holes when used with appropriate coolant and fixturing. For what is a Twist Drill used? A Twist Drill such as the MetavCUT Twist Drill is mainly used when working on high‑strength materials and larger diameters; its geometry lends itself to easy re‑grinding and it endures higher loads, making it a reliable choice for heavy‑duty metalworking. Which three drill types exist? The main drill categories are Metal drills, Wood drills and Stone/Concrete drills, each optimised in geometry and cutting edge for their respective materials. Why are Twist Drills point‑ground? Point‑grinding reduces the chisel edge at the tip of the Twist Drill, lowering friction and thus the required feed forces; at the same time the ground point improves centring of the tip in the workpiece for more accurate starts. Can a Metal drill be used for wood? A Metal drill like the MetavCUT Twist Drill can be used in Wood, but guidance is reduced and the finish may be less clean; however such drills are easier to re‑sharpen and exhibit lower self‑feed behaviour. At what drilling depths is the Twist Drill most commonly used? Twist Drills are commonly applied for through‑solid holes; in typical practice they are used for diameters up to 20 mm and drilling depths up to approx. 100 mm, depending on geometry and setup. What is better, HSS or HSSE? The general assumption that HSSE is categorically superior to HSS is not universally correct; selection should consider actual working conditions to determine whether the additional cost of HSSE is justified.

Twist Drill — Extra Long HSS-G Drill, 13 mm, 135° Tip, Bright Finished, Fully Ground, DIN 1869 (by MetavCUT) The Twist Drill is an extra-long HSS-G drill designed for deep metal drilling with a 13 mm diameter, suitable for use in drilling machines. Extra-long design for deep boreholes 13 mm diameter for robust metal work 135° tip angle for harder materials Fully ground flutes for precise holes Complies with DIN 1869 for deep drilling Greater precision through material and geometry The HSS-G construction combines wear resistance with cutting performance to meet the demands of metalworking. With a 135° tip angle, the bit enters harder materials more smoothly and reduces walking on the surface. The fully ground flute geometry produces sharp cutting edges and high concentricity, resulting in cleaner, more accurate holes when working with legierte and unlegierte steels. This design is particularly advantageous when hole quality and repeatability matter. Built for deep, hard-to-reach drilling Thanks to its extra-long overall length and a long spiral section, this drill is intended for deep-hole applications or when access is restricted. The longer working length lets assemblies or fixtures remain in place while the hole is extended, reducing setup changes. The long spiral also supports efficient chip evacuation during deeper passes, which helps maintain cutting efficiency and surface finish when drilling steel, cast iron and non-ferrous metals. Application guidance and safe use The Twist Drill is optimised for use in a drilling machine and is particularly suited to demanding jobs in Grauguss, legierte and unlegierte Stahl up to 1000 N/mm². For best results, use appropriate cutting fluid and moderate feed to avoid excessive stress; fully ground HSS bits can be sharper but also more brittle than rolled equivalents. The DIN 1869 specification indicates a deep-spiral geometry that improves chip removal in extended bores under challenging conditions. Who benefits from this drill and why Professional workshops and metalworking specialists who require reliable deep-hole performance will value the combination of 13 mm diameter, long reach and precise flute grinding. The tool is designed to deliver consistent hole quality in production or repair environments where access or component geometry demands extended tooling. For manual operations in portable drills, consider machine stability and cooling to minimise breakage risk. We recommend MetavCUT’s extra-long Twist Drill for demanding deep metal drilling — for individual technical advice or to clarify suitability for your application, METAV Werkzeuge provides competent consultation: eMail info@metav-werkzeuge.com, Tel +49 2822 7131930, WhatsApp +49 170 2837271 Technical Data Designation: Twist Drill Brand: MetavCUT SKU: 34130-FDA Diameter: 13 mm Tip angle: 135° Type / Execution: extra long Finish / Colour: bright finished Shaft execution: fully ground Spiral length: 330 mm Overall length: 480 mm Material: HSS-G Norm: DIN 1869 For use in: Drilling Machine Model series: Standard Line Application: Drills for metal Packaging unit: 10 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill used for and which materials suit it best? The MetavCUT Twist Drill is primarily used for machining high-strength materials and larger bore diameters; it is particularly effective on alloyed and unalloyed Steel, Cast Steel, Cast Iron and hard plastics, delivering clean, precise holes even under demanding conditions. Which three drill types are commonly distinguished? In general classification you will find Metal drills, Wood drills and Stone/Concrete drills; the MetavCUT Twist Drill belongs to the Metal drill category and is engineered accordingly. Can the MetavCUT Twist Drill be used in a handheld drilling machine? The Twist Drill can be used with a handheld Drilling Machine, but due to its extra-long and fully ground design it performs best in stable machine setups with appropriate cooling; for portable use ensure secure clamping and controlled feed to avoid breakage.

Twist Drill Spiralbohrer – Twist Drill, 2.5 mm Ø, 135° tip, extra long, bright finished, fully ground, HSS‑G (DIN 1869) A Twist Drill Spiralbohrer designed for deep, precise metal drilling in Drilling Machines and hand-held drills. Extra-long design for deep holes HSS‑G fully ground for faster, precise drilling 135° tip angle for harder materials Conforms to DIN 1869 for demanding applications High-performance material for demanding Metalwork HSS‑G construction delivers a combination of hardness and cutting-edge geometry that benefits metalworking tasks. The fully ground flute geometry provides sharp cutting edges and high runout accuracy, which results in cleaner holes and less rework. According to internal data, the ground HSS design can enable up to 40% faster drilling while requiring approximately 50% less feed force compared with conventional rolled HSS bits, improving efficiency in production and workshop environments. Built for deep holes and tough materials The extra long overall length of 225 mm with a spiral length of 150 mm makes this Twist Drill especially suitable when access is limited or when long through-holes are needed. The 135° tip angle is optimised for harder materials — it reduces initial biting and shortens approach time into the workpiece, which is advantageous when drilling stainless steel and other high-strength alloys up to 1000 N/mm². Precision geometry and recommended usage The fully ground (CNC‑ground) flute and shank ensure high concentricity and precise hole quality, which is particularly important for metal and hard-plastic applications. Ground Twist Drills are sharper and generally produce superior surface finish; however, they can be relatively more brittle than rolled types. For best results, use the MetavCUT Twist Drill in stationary Drilling Machines with appropriate cooling and controlled feed to extend tool life. Typical applications and target users This Twist Drill is intended for professional machinists, maintenance technicians and metalworking shops that require reliable deep-hole performance. It is suitable for legierte und unlegierte Stahl (alloyed and unalloyed steel), Gussstahl, Gusseisen, Sintereisen, Temperguss, Nichteisenmetalle and hard plastics. The Extra Long design supports drilling operations where standard-length bits are insufficient, while the DIN 1869 specification assures compatibility with industrial production standards. Highly recommended: Choose the MetavCUT Twist Drill for deep, precise metal drilling — contact METAV Werkzeuge for expert technical advice via email info@metav-werkzeuge.com, by phone +49 2822 7131930 or WhatsApp +49 170 2837271 Designation: Twist Drill (Spiralbohrer) Brand: MetavCUT SKU: 34025-FDA Diameter: 2.5 mm Tip angle: 135° Overall length: 225 mm Spiral length: 150 mm Execution: extra long Colour/Finish: bright finished Shank execution: fully ground Material: HSS‑G Standard: DIN 1869 For machine: Drilling Machine / Hand Drills Application: Drills for metal Model series: Standard Line Packaging unit: 10 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Is the MetavCUT Twist Drill suitable for stainless steel and high-strength alloys? The MetavCUT Twist Drill is designed to machine materials such as stainless steel and other high-strength alloys up to around 1000 N/mm²; its 135° tip and HSS‑G ground geometry help reduce drilling forces and improve centring in tougher materials. Can the MetavCUT Twist Drill be used in a hand-held drill? The MetavCUT Twist Drill can be used in hand-held drills for lighter tasks, but optimal performance and tool life are achieved in a stationary Drilling Machine with adequate clamping and coolant due to the Extra Long design and ground geometry. What is a Twist Drill used for? A Twist Drill is mainly applied to the machining of high-strength materials and larger drill diameters; its ground geometry is easy to re‑sharpen and resists heavier loads, making it suitable for demanding metal drilling. Which three drill types exist? The three main drill categories are metal drills, wood drills, and stone/concrete drills. Why are Twist Drills sharpened? Sharpening reduces the cross‑edge at the drill point; by re‑pointing the tip, frictional forces are substantially lowered so that less feed force is needed and the drill centres more accurately in the workpiece. Can you drill wood with a Twist Drill? A metal Twist Drill can be used in wood, but guidance and finish are generally inferior compared with dedicated wood drills; metal bits are easier to re‑sharpen and have less self‑feeding tendency. For which drilling depths is the Twist Drill most commonly used? A through-hole in solid material is typically made with a Twist Drill; for diameters up to 20 mm and drilling depths up to 100 mm, the Twist Drill is the most frequently used tool. What is better, HSS or HSSE? The common belief that HSSE is automatically superior to HSS is not universally correct; assess the working conditions to determine whether the higher cost of HSSE is justified for your application.

Der extra lange Spiralbohrer von MetavCUT kombiniert HSS‑G Geschliffen, Tieflochspirale und einen Spitzenwinkel von 135° für schnelle, präzise Bohrungen in Stahl und Guss; die geschliffene Geometrie sorgt für hohe Rundlaufgenauigkeit, während die längere Arbeitslänge tiefe Bohrungen ermöglicht. Für Beratung und Bestellung stehen Metav Werkzeuge und die Fachberatung in Emmerich zur Verfügung. Spiralbohrer — HSS‑G Extra lang (MetavCUT Standard Line) Der Spiralbohrer ist ein extra langer, geschliffener HSS‑G Bohrer nach DIN 1869 für tiefe Bohrungen in legierten und unlegierten Stahl sowie Gusswerkstoffe Extra lange Ausführung für tiefe Bohrungen HSS‑G geschliffen für hohe Rundlaufgenauigkeit Spitzenwinkel 135° für harte Werkstoffe Gesamtlänge 200 mm, Spirallänge 135 mm Geeignet für Handbohrmaschine und stationären Einsatz Höhere Effizienz durch geschliffene HSS‑Geometrie Die HSS‑G Ausführung mit CNC‑Schliff ermöglicht sehr scharfe Schneiden und damit bis zu 40 % schnelleres Bohren bei deutlich geringerem Anpressdruck. Durch die präzise gefertigte Spannutengeometrie entsteht eine bessere Spanabfuhr und saubere Bohrlöcher, was Nachbearbeitung reduziert. Anwender profitieren von kürzeren Bearbeitungszeiten und stabileren Prozessbedingungen bei legierten Stählen und Gusseisen. Extra lange Bauform für tiefe und schwer zugängliche Bohrungen Die Ausführung Extra lang mit einer Gesamtlänge von 200 mm und einer Spirallänge von 135 mm ist speziell für tiefe Bohrungen und schwer zugängliche Bereiche konzipiert. Bei tiefen Bohrungen verbessert die Tieflochspirale die Spanführung und verringert Verstopfungen. Für beste Ergebnisse empfiehlt sich kühlmittelführung und stationärer Halt der Bohrmaschine, um die Gefahr von Bruch durch die geschliffene, etwas sprödere Ausführung zu minimieren. Praxistipps und Einsatzbereich für den Werkstattalltag Für den Durchmesser 2 mm empfiehlt sich die Einstufung in den Standard‑Bereich: Direktes Bohren ist möglich, bei hoher Präzision vorher mit einem Zentrierbohrer anpunkten. Der Spiralbohrer eignet sich für Handbohrmaschine und stationäre Säulenmaschinen gleichermaßen, wobei bei Verwendung an mobilen Geräten eine ruhige Führung und moderate Vorschubgeschwindigkeit die Standzeit erhöht. Kühlung verlängert die Lebensdauer besonders bei höheren Zugfestigkeiten. Materialverträglichkeit und präzise Anwendungsempfehlung Der Bohrer ist ausgelegt für legierte und unlegierte Stähle, Gussstahl, Gusseisen, Sintereisen, Temperguss, Nichteisenmetalle und harte Kunststoffe. Der Spitzenwinkel 135° reduziert das Anlaufen in harten Werkstoffen und verbessert das Anbohrverhalten bei Edelstahl und gehärteten Werkstoffen. Für großvolumige Serien in gehärtetem Stahl empfiehlt sich jedoch Hartmetallwerkzeug; dieses Produkt punktet bei universellen Metallaufgaben mit hoher Präzision. Für präzise Tieflochbohrungen empfiehlt MetavCUT den Einsatz dieses HSS‑G Spiralbohrers über Metav Werkzeuge; bei Fragen zur Anwendung kontaktieren Sie unsere Fachberatung per E‑Mail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 Produktmerkmale Artikelnummer: 34020-FDA Marke: MetavCUT Serie: Standard Line Bezeichnung: Spiralbohrer Norm: DIN 1869 (Spiralbohrer‑Norm) Fakten Durchmesser: 2 mm Gesamtlänge: 200 mm Spirallänge: 135 mm Spitzenwinkel: 135° Besonderheiten Material: HSS-G Schaft Ausführung: geschliffen Ausführung: extra lang Für Bohrmaschine: Handbohrmaschine Farbe: blank Verpackungseinheit: 10 SKU: 34020-FDA UID: 34020-FDA FAQ Welche Werkstoffe lassen sich mit dem Bohrer bearbeiten? Der MetavCUT Spiralbohrer (HSS‑G, Standard Line, SKU 34020-FDA) ist geeignet für legierte und unlegierte Stähle, Gussstahl, Gusseisen, Sintereisen, Temperguss, Nichteisenmetalle und harte Kunststoffe; bei sehr gehärteten Werkstoffen empfiehlt sich auf Hartmetall umzusteigen. Ist der Bohrer für Handgeführte Bohrmaschinen geeignet? Ja, der Spiralbohrer von MetavCUT wurde für den Einsatz an Handbohrmaschinen und stationären Maschinen konstruiert; bei mobiler Anwendung auf gute Führung und Kühlung achten, um Bruchrisiken zu minimieren. Wann ist der Spitzenwinkel 135° sinnvoll? Der 135° Spitzenwinkel des MetavCUT Spiralbohrers reduziert Anlaufprobleme und eignet sich besonders bei härteren Werkstoffen wie Edelstahl oder gehärtetem Stahl, da er die Anbohrzeit verkürzt und das Wandern reduziert. Warum ist der Bohrer geschliffen und was bedeutet das praktisch? Geschliffene Spannuten (HSS‑G) beim Spiralbohrer sorgen für sehr scharfe Schneiden und hohe Rundlaufgenauigkeit; das erhöht Präzision und Oberflächenqualität, verlangt aber vorsichtigere Handhabung und Kühlung, da die Werkzeuge spröder sein können. Wie viel tiefer kann man mit der extra langen Ausführung bohren? Die extra lange Bauform des MetavCUT Spiralbohrers ermöglicht tiefe Bohrungen dank verlängerter Arbeitslänge und Tieflochspirale; für sehr tiefe Löcher empfiehlt sich zusätzlich eine abgestufte Bohrfolge zur Entlastung der Querschneide.

Twist Drill – HSS‑G, Ø 3.2 mm, 135° Tip, Extra Long, Bright Finished (for Drilling Machine), DIN 1869 The Twist Drill is an extra‑long HSS‑G drill for Drilling Machines, engineered for deep metal drilling and precise hole creation in demanding workshop and industrial applications. Extra‑long design for deep metal holes 135° tip for hardened and stainless steels HSS‑G fully ground for precise, clean holes Conforms to DIN 1869 for dependable results Bright finished shank with excellent runout accuracy High performance for deep and demanding metal drilling Designed to deliver measurable efficiency gains, this HSS‑G Twist Drill combines Extra Long geometry with a 135° Tip to reduce start wandering and to penetrate harder materials more reliably. The ground spiral geometry lowers feed forces, enabling faster spindle advance and improved chip evacuation for deep holes. As a result, users experience reduced cycle times and less tool chatter when machining legierte and unlegierte steels, cast steels and harder alloys. Precision manufacturing and what it means for workshop use Because the flute geometry is produced by CNC grinding rather than rolling, the Fully Ground shank and flutes offer sharp cutting edges and superior concentricity. This manufacturing method yields cleaner Holes and better surface finish, especially in metalworking. Note that ground HSS tools can be more brittle than rolled equivalents; applying appropriate coolant and avoiding excessive pecking without lubrication helps to extend tool life and maintain dimensional accuracy. Suited materials and practical application scenarios This Twist Drill is intended primarily for metalworking: Grauguss, legierte and unlegierte Steel up to 1000 N/mm², Gusseisen, non‑ferrous Metals and hard Plastics are appropriate workpieces. Its Deep Hole capability makes it a solid choice for toolrooms, maintenance departments and production lines where through‑holes and blind holes with extended depth are required. For portable or stationary Drilling Machines, the extra overall length supports access to recessed areas without sacrificing Hole quality. Tips for selection, handling and storage to maximise life Select the Diameter and the Extra Long variant when hole depth exceeds standard tool reach; shorter drills are still preferable for small blind depths to reduce deflection. Start with a pilot or centre drill for improved centring when working with stainless or hardened materials. Store Twist Drills in a dry, protected rack to prevent edge damage; regrinding is feasible for HSS‑G tools, restoring cutting geometry while preserving the tool blank for further use. Choose MetavCUT quality for precision deep‑hole drilling — METAV Werkzeuge provides comprehensive technical advice if unsure whether this Twist Drill meets specific requirements. Contact METAV Werkzeuge by email at info@metav-werkzeuge.com, by phone at +49 2822 7131930 or via WhatsApp at +49 170 2837271 for tailored support. Designation: Twist Drill Brand: MetavCUT SKU: 34032-FDA Diameter: 3.2 mm Tip Angle: 135° Overall Length: 250 mm Spiral Length: 170 mm Execution: Extra Long Shank Design: Fully Ground Surface Finish: Bright Finished Material: HSS‑G Standard: DIN 1869 For Use With: Drilling Machine Model Series: Standard Line Packaging Unit: 10 Application: Drills for Metal Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the primary use of a Twist Drill? The MetavCUT Twist Drill is mainly used for machining high‑strength materials and larger hole diameters; its design suits deep drilling and tasks where the tool must withstand higher mechanical loads, offering good suitability for steels, cast irons and hard plastics. Which three drill types exist? Common categories are metal drills, wood drills and stone/concrete drills; the MetavCUT Twist Drill belongs to the metal drill group and is optimised for metalworking applications. Why are Twist Drills sharpened at the point? Sharpening reduces the cross‑edge at the tip, which lowers friction and required feed force and improves centring in the workpiece; the MetavCUT Twist Drill benefits from this by achieving more accurate starts and less walking. Can a metal Twist Drill be used to drill wood? A metal Twist Drill can be used in wood, but the MetavCUT metal drill will usually produce less precise guidance and a rougher finish than a dedicated wood bit; the advantage lies in easier resharpening and lower self‑feeding tendency. For which drilling depths is the Twist Drill most used? For solid drilling operations up to diameters around 20 mm and depths up to 100 mm, the Twist Drill is the most commonly used tool; the MetavCUT Extra Long variant is specifically intended where deeper access or extended working length is required. Is HSS or HSSE better for these applications? The general assumption that HSSE is always superior to HSS is not universally correct; evaluate working conditions carefully to determine whether the higher cost of HSSE is justified for the intended MetavCUT Twist Drill application.

Der MetavCUT Spiralbohrer in HSS-G-Ausführung kombiniert hohe Schnittgeschwindigkeit, extra lange Bauform und präzisen CNC-Schliff zu einer Lösung für tiefe Metallbohrungen; die geschliffene Geometrie sorgt für saubere Bohrbilder und die Tieflochspirale nach DIN 1869 ermöglicht sichere Spanabfuhr unter erschwerten Bedingungen, bei Bedarf technische Beratung direkt über Metav anfordern. Spiralbohrer von MetavCUT, HSS‑G, 3,5 mm Spiralbohrer von MetavCUT für Metallbohrungen, extra lange Ausführung für tiefe und schwer zugängliche Löcher MetavCUT HSS‑G Ausführung für Stahl und Guss Extra lange Bauform, Gesamtlänge 265 mm Geschliffene Schaftausführung für hohe Rundlaufgenauigkeit Tieflochspirale nach DIN 1869 für bessere Spanabfuhr Spitzenwinkel 135° optimiert für härtere Werkstoffe Mehr Leistung bei anspruchsvollen Metallbohrungen Die HSS-G-Legierung bietet deutlich reduzierte Anpresskraft und ermöglicht laut Hersteller ein bis zu 40 % schnelleres Bohren bei gleichzeitig 50 % geringerer Anpresskraft im Vergleich zu herkömmlichen HSS-Varianten. Für Anwender bedeutet das messbar kürzere Taktzeiten und weniger Ermüdung beim Bohren in legiertem und unlegiertem Stahl sowie in Gusswerkstoffen. Die Kombination aus geschliffener Geometrie und Tieflochspirale liefert saubere, präzise Bohrbilder und erleichtert das Nachbearbeiten. Präzision und Handhabung durch geschliffene Verarbeitung Die voll geschliffene Schaft- und Spiralgeometrie resultiert in scharfen Schneiden und hoher Rundlaufgenauigkeit, was besonders bei Passungsbohrungen relevant ist. Diese Qualität bietet Vorteile in der Serienfertigung und bei anspruchsvollen Einzelteilen. Wegen der höheren Sprödigkeit geschliffener Werkzeuge empfiehlt sich der Einsatz mit geeigneter Kühlung und, wo möglich, eine Spannvorrichtung oder stationäre Aufnahme, um die Lebensdauer zu maximieren. Extra lange Bauform für tiefe Bohrungen Mit einer Gesamtlänge 265 mm und einer Spirallänge 180 mm ist die Ausführung speziell für tiefe Bohrungen ausgelegt, bei denen Standardlängen an ihre Grenzen stoßen. Die Tieflochspirale nach DIN 1869 verbessert die Spanabfuhr deutlich und reduziert die Gefahr von Verstopfungen in langen Bohrgängen. Für sichere Ergebnisse empfehlen sich moderate Vorschübe, ausreichende Kühlung und bei sehr langen Bohrtiefen schrittweises Aufbohren. Einsatzzwecke und Zielgruppe Die Ausführung richtet sich an Werkstätten, Metallbauer und anspruchsvolle Heimwerker, die präzise Bohrungen in Grauguss, legierten und unlegierten Stahl bis 1000 N/mm², Gusseisen sowie Nichteisenmetalle und Hartkunststoffe ausführen müssen. Die Kombination aus MetavCUT-Qualität und Standard Line Verarbeitung macht den Bohrer zur praktischen Wahl für Anwender, die auf Verlässlichkeit und lange Einsatzfähigkeit setzen. Empfehlung: Auf die extra lange MetavCUT HSS‑G Ausführung setzen und für tiefe Metallbohrungen direkt über Metav beziehen — telefonisch +49 2822 7131930 oder per eMail info@metav-werkzeuge.com; SKU 34035‑FDA verfügbar. Produktmerkmale Artikelnummer: 34035-FDA Marke: MetavCUT Serie: Standard Line Bezeichnung: Spiralbohrer Daten Durchmesser: 3,5 mm Gesamtlänge: 265 mm Spirallänge: 180 mm Spitzenwinkel: 135° Verpackungseinheit: 10 Besonderheiten Material: HSS-G Norm: DIN 1869 Ausführung: extra lang Schaftausführung: geschliffen Farbe: blank Für Bohrmaschine: Handbohrmaschine FAQ Ist der Bohrer für Edelstahl und gehärtete Werkstücke geeignet? Der MetavCUT Spiralbohrer HSS‑G 3,5 mm (SKU 34035‑FDA) ist für gehärtete Werkstoffe bis etwa 1000 N/mm² ausgelegt; durch den Spitzenwinkel 135° lässt sich die Anbohrung bei härteren Materialien verbessern, Kühlung und angepasste Schnittparameter sind jedoch erforderlich. Kann der Bohrer mit einer Handbohrmaschine verwendet werden? Ja, die Ausführung erlaubt den Einsatz mit einer Handbohrmaschine, allerdings empfiehlt das Standard Line Werkzeug bei der extra langen Bauform eine stabile Führung oder Spannvorrichtung, um Ablenkungen und Bruchrisiken zu minimieren. Was bedeutet geschliffen im Vergleich zu gewalzt? Bei geschliffenen Spiralbohrern wie dem MetavCUT Modell erfolgt die Formgebung der Spannuten durch CNC‑Schliff; das Ergebnis sind scharfe Kanten und hohe Rundlaufgenauigkeit, allerdings mit höherer Sprödigkeit im Vergleich zu gewalzten Bohrern. Wie tief lassen sich Löcher mit dieser Ausführung bohren? Die Gesamtlänge 265 mm und die Spirallänge 180 mm sind für tiefe Bohrungen ausgelegt; für besonders tiefe oder kritische Anwendungen empfiehlt sich schrittweises Aufbohren und kontinuierliche Kühlung, um Spanbildung und Erwärmung zu vermeiden. In welcher Verpackungsgröße wird der Bohrer geliefert? Der MetavCUT Spiralbohrer HSS‑G 3,5 mm wird in der Verpackungseinheit 10 geliefert (SKU 34035‑FDA), geeignet zur Versorgung von Werkstattarbeitsplätzen und für kleinere Serien.

MetavCUT Twist Drill — 3 mm, 135° point angle, extra long, bright finished, fully ground, HSS‑G, DIN 1869 the MetavCUT Twist Drill is a high‑precision drilling tool designed for deep metal drilling with hand drills and drilling machines, offering extra length and a 135° point for reliable centring and efficient penetration. Extra‑long design for deep holes Fully ground HSS‑G for precise, clean bores 135° point angle for harder materials Bright finished surface for corrosion resistance Optimised geometry for use in drilling machines Engineered for accurate metal drilling and durable results The HSS‑G material and DIN 1869 conformity ensure the bit is suited for demanding metalworking tasks. The fully ground flute geometry produces sharp cutting edges and a high runout accuracy, which results in cleaner bores and consistent hole dimensions. This construction is particularly advantageous when drilling alloyed and unalloyed steels, cast iron and non‑ferrous metals, because it minimises deformation at the hole edge and supports repeatable results in production or repair work. Extra length for hard‑to‑reach and deep holes With a total length of 240 mm and a spiral (working) length of 160 mm, the extra long execution enables access where standard bits cannot reach. This makes the tool ideal for deep‑hole operations and applications where the workpiece geometry or fixturing places the drill axis far from the operator. The bright finished surface helps reduce corrosion risk during storage and handling and supports smoother chip evacuation in deeper bores. Faster drilling with lower feed force — practical benefits The fully ground HSS geometry offers significant performance advantages: it can drill up to 40% faster and requires approx. 50% less feed force compared with conventional HSS bits of rolled geometry. The 135° point angle reduces initial bite in harder materials and shortens pilot time, improving control and reducing the risk of walking. For best results, use appropriate coolant and, when possible, a stationary setup to mitigate the inherently higher brittleness of ground drills. Recommended applications and user profile This tool is optimised for professional metalworkers, toolrooms and maintenance technicians who need precise, deep holes in steels, cast materials and hard plastics. The bit is suited for use in a Drilling Machine as well as robust hand‑held drills when carefully applied. If in doubt about suitability for a specific alloy or machining parameter, METAV Werkzeuge provides expert consultation to ensure the right selection for the task. Choose MetavCUT’s precision Twist Drill for demanding deep‑hole metalwork — for personalised technical advice and ordering assistance contact METAV Werkzeuge by email at info@metav-werkzeuge.com, by phone at +49 2822 7131930 or via WhatsApp at +49 170 2837271 Designation: Twist Drill Brand/Manufacturer: MetavCUT SKU: 34030-FDA Diameter: 3 mm Point angle: 135° Execution / Type: extra long Colour: bright finished Shaft execution / Shank finish: fully ground Spiral length: 160 mm Total length: 240 mm Material: HSS‑G Standard: DIN 1869 For use in: Drilling Machine (Hand drill compatibility) Application: Drills for metal Model series: Standard Line Packaging unit: 10 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill mainly used for? The MetavCUT Twist Drill is primarily used for drilling high‑strength materials and larger diameters; it is especially effective for deep holes and tasks where a longer overall length is required, providing reliable performance in alloyed and unalloyed steels as well as cast materials. Which three drill types exist? The three main categories are metal drills, wood drills and masonry/concrete drills; the MetavCUT Twist Drill belongs to the metal drill family and is engineered specifically for metalworking applications.

Twist Drill — Drill for Drilling Machine, Ø 4.2 mm, 135°, HSS‑G, Extra‑Long, Bright Finished, DIN 1869 (MetavCUT) The Twist Drill is an extra‑long HSS‑G drill for deep metal holes, designed for use in Drilling Machines and industrial applications. Extra‑long design for deep hole drilling HSS‑G material for high cutting performance 135° point angle for hard materials Fully ground shank for high concentricity Complies with DIN 1869 for deep‑hole applications Precision and power for deep metal drilling The Twist Drill from MetavCUT is engineered as an extra‑long HSS‑G bit to reach depths that standard drills cannot. The 135° point angle reduces walking on hard materials and shortens the initial penetration time, which is especially valuable when drilling thicker plates or components made from stainless or alloyed steels. Compliance with DIN 1869 guarantees a geometry and spiral design optimised for demanding, deep‑hole applications, providing consistent results in production and workshop use. Faster machining with a ground geometry A fully ground (HSS‑G) spiral geometry yields very sharp cutting edges and excellent run‑out precision. The CNC grinding process produces a stable flute profile and clean bore surfaces; as a result, the MetavCUT bit can deliver up to 40% faster drilling and requires significantly less axial pressure compared with conventional rolled HSS drills. This translates into reduced operator fatigue and improved cycle times when used with appropriate coolant and steady fixturing. Materials and suitable applications This drill is specified for metalworking: it is suitable for legierte und unlegierte Stähle, Gray Cast Iron, Brass, Non‑Ferrous Metals and Hard Plastics within the recommended hardness limits. The extra‑long overall and working lengths make it ideal where through‑holes or deep blind holes are required and where access is limited. Use it in Drilling Machines and machine tool set‑ups that provide stable clamping and coolant flow to extend life and maintain hole quality. Handling recommendations and support For best results, secure the workpiece and use steady feed rates tailored to the material. Because ground HSS bits can be more brittle than rolled variants, avoid shock loads and always apply suitable cooling for long drilling operations. If uncertain about feeds, speeds or the correct bit for a specific alloy or thickness, METAV Werkzeuge offers comprehensive technical support and advice. Their experienced team will help choose the right tooling and operating parameters for the application. For reliable deep‑hole machining choose the MetavCUT extra‑long HSS‑G Twist Drill and request tailored machining advice from METAV Werkzeuge — email info@metav-werkzeuge.com or call +49 2822 7131930, WhatsApp +49 170 2837271 Designation: Twist Drill (Extra‑long) Brand: MetavCUT Diameter: 4.2 mm Point angle: 135° Execution: Extra‑long Overall length: 280 mm Spiral length: 190 mm Material: HSS‑G Shank execution: Fully ground Colour: Bright finished Model series: Standard Line Application: Drills for metal Suitable for: Drilling Machine Standard: DIN 1869 Manufacturer: MetavCUT Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill used for? The MetavCUT Twist Drill is used primarily for drilling in metal; it is designed for deep holes and for machining high‑strength and hard materials where an extra‑long working length is required. The geometry and HSS‑G material suit alloyed and unalloyed steels, cast irons and other non‑ferrous metals. Which three drill types exist? Common drill types are metal drills, wood drills, and stone/concrete drills. The MetavCUT Twist Drill belongs to the metal drill category and is optimised for machining metallic materials. Why are Twist Drills point‑ground? Point grinding reduces the cross‑cut at the tip, lowering friction and required feed force. For the MetavCUT Twist Drill a ground tip improves centring and reduces radial run‑out, which results in cleaner holes and more consistent drilling under load. Can a metal Twist Drill be used in wood? A metal Twist Drill like the MetavCUT bit can be used in wood, but guidance and finish are inferior to purpose‑made wood drills. Metal drills are easier to re‑grind and have less aggressive self‑feed, so hole quality and tracking may be reduced in timber.

Twist Drill — Drill for Metal (Ø 4.5 mm, 135° Point, Extra Long, Bright Finished, HSS-G, DIN 1869) The Twist Drill is an Extra Long Drill for Metal designed for deep drilling in Drilling Machines and workshop applications. Extra Long design for deep drilling Fully Ground shank for high runout accuracy HSS-G Material for hard metal performance 135° Point Angle optimized for tough alloys Bright Finished surface for consistent chip evacuation Deep reach and faster metal removal for demanding tasks Engineered as an Extra-Long solution, this Twist Drill delivers extended reach with a Gesamtlänge of 295 mm and a Spiral Length of 200 mm, making it ideal for deep-hole tasks. The HSS-G construction and the special flute geometry enable up to 40 % faster drilling and require 50 % less Anpresskraft compared with conventional HSS tools, which translates to higher productivity on long runs and reduced operator fatigue. Precision geometry that creates clean, accurate holes Thanks to the Fully Ground flute geometry and precise Points, the drill achieves very sharp cutting edges and excellent Rundlaufgenauigkeit. The 135° Point Angle is tailored for harder Werkstoffe and shortens Anbohrzeit, while the DIN 1869 specification ensures consistent quality. Because ground tools can be more brittle, stationary operation with coolant is recommended to preserve tool life and hole quality. Suited materials and professional workshop applications This Twist Drill is intended for a wide range of Metall applications, including legierten and unlegierten Stahl, Gussstahl, Gusseisen, Sintereisen, Temperguss, Nichteisenmetalle and Hartkunststoff, and is rated for materials up to 1000 N/mm². Workshops, toolrooms and industrial users benefit from the combination of depth capability and cutting performance when working on components that require deep, precise bores. Handling, sharpening and practical tips for longer service life For best results mount the drill concentrically in a suitable Chuck of a Drilling Machine and use sufficient coolant during operation. The Ausspitzung (point preparation) reduces Querschneide and lowers Reibkräfte, so lower Vorschubkräfte are sufficient and centering improves. If regrinding is necessary, maintain the 135° geometry to preserve performance; note that ground HSS-G drills are easier to resharpen yet require careful handling to avoid breakage. If unsure whether this tool fits specific requirements, METAV Werkzeuge offers comprehensive technical advice to help select the right solution. Strong recommendation: Choose the MetavCUT Twist Drill for deep, demanding metal drilling and consult METAV Werkzeuge for expert support — Email: info@metav-werkzeuge.com · Phone: +49 2822 7131930 · WhatsApp: +49 170 2837271 Technical Information Designation: Twist Drill Brand: MetavCUT SKU: 34045-FDA Diameter: 4.5 mm Overall Length: 295 mm Spiral Length: 200 mm Point Angle: 135° Execution: extra long Colour: bright finished Shank Execution: fully ground Material: HSS-G Norm: DIN 1869 For: Drilling Machine Model Series: Standard Line Application: Drills for metal Packaging Unit: 10 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill used for? The MetavCUT Twist Drill is primarily applied to the machining of high-strength Werkstoffe and large bore diameters; its form allows relatively easy resharpening and it withstands considerable Belastungen, making it suitable for demanding metalworking tasks. Which three drill types exist? There are three common drill categories: Metal Drills, Wood Drills and Stone/Concrete Drills; the MetavCUT Twist Drill belongs to the Metal Drills group and is optimized for metalwork. Why are Twist Drills pointed? The point geometry reduces the Querschneide at the Tip of the Twist Drill; by pointing, frictional forces are significantly lowered and smaller Vorschubkräfte are needed while the Tip centers better in the Workpiece. Can you use metal drills in wood? A Metal Drill such as the MetavCUT Twist Drill can be used in Wood, but guidance is poorer and the bore finish may be less clean; however, Metal Drills are easier to resharpen and show less self-feed tendency. For which bore depths is the Twist Drill most commonly used? A through-hole is commonly executed with a Twist Drill; for diameters up to 20 mm and drill depths up to 100 mm, the Twist Drill is the most frequently used tool, while the extra-long MetavCUT version extends that capability for deeper bores. Is HSS or HSSE better? The general belief that HSSE steels are inherently superior to HSS is not universally correct; evaluate working conditions carefully to decide whether the higher investment in HSSE is justified for your specific MetavCUT application.

Twist Drill — Extra long HSS‑G Drill Bit for Metal (4 mm, 135°) The Twist Drill is an extra‑long HSS‑G drill bit designed for deep metal drilling with a 4 mm diameter and a 135° tip angle, suitable for use in drilling machines and stationary equipment. Extra‑long HSS‑G design for deep drilling 4 mm diameter with 135° tip for hard metals Fully ground shank for high concentricity DIN 1869 standard for deep hole performance Bright finish for improved chip evacuation Superior Material for Demanding Metalwork The Twist Drill is manufactured from HSS‑G, providing high red hardness and wear resistance for demanding tasks. The combination of the DIN 1869 geometry and a 135° tip angle makes this bit particularly effective in harder materials, reducing chatter and improving centring when entering tough surfaces. The construction gives reliable hole quality and consistent performance in legated and unlegated steels, cast iron and non‑ferrous metals. Made for Deep, Hard‑to‑Reach Holes With a Total Length of 280 mm and a Spiral Length of 190 mm, this extra‑long design enables drilling far beyond standard reach, ideal for deep bore requirements or operations where access is restricted. The extended working length minimises the need for extensions and permits cleaner chip removal over long depths. For deep metal bores, the geometry supports sustained performance while maintaining hole straightness. Precision Finish and Easier Cutting A fully ground shank and CNC‑ground flutes ensure sharp cutting edges and superior runout, delivering precise holes and smooth chip flow. The bright finish reduces friction and aids chip evacuation during drilling. Compared with rolled HSS variants, the ground geometry allows up to 40% faster drilling and demands 50% less feed force, which translates to less operator effort and more efficient cycles on stationary or machine drills. Recommended Applications and Safe Use This Twist Drill is optimised for drilling in metal, including alloyed steels, cast steels and hard plastics. Due to the ground geometry, the bit is best used in machine or drill press environments with appropriate cooling; ground HSS can be more brittle than rolled designs and benefits from coolant and moderate feed rates to avoid breakage. For non‑industrial handheld use, verify machine stability and apply reduced feed to protect the tool. Who Benefits Most Workshops and professionals who need accurate deep holes in tougher materials will appreciate the combination of extra reach and precision. The bit suits machine shops, toolrooms and maintenance departments that require reproducible hole quality and longer working lengths without sacrificing centring performance. MetavCUT’s Standard Line targets users who prioritise precision and consistent results. We recommend the MetavCUT extra‑long Twist Drill for precision deep metal drilling — for competent advice and tailored technical support contact METAV Werkzeuge at info@metav-werkzeuge.com, phone +49 2822 7131930 or WhatsApp +49 170 2837271 Designation: Twist Drill (Spiralbohrer) Brand: MetavCUT SKU: 34040-FDA Diameter: 4 mm Tip Angle: 135° Material: HSS‑G Standard: DIN 1869 Execution: extra long Total Length: 280 mm Spiral Length: 190 mm Shank Finish: fully ground (geschliffen) Colour/Finish: bright finished (blank) For Use With: Drilling Machine (Handbohrmaschine) Application: Drills for metal (Bohrer für Metall) Model Series: Standard Line Packaging Unit: 10 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials is the Twist Drill by MetavCUT best suited for? The MetavCUT Twist Drill is primarily designed for metalworking and performs well in alloyed and unalloyed steels, cast steel, cast iron and non‑ferrous metals; its HSS‑G composition and 135° tip help when machining harder materials and improve centring and hole quality. How does the extra‑long execution improve drilling performance? An extra‑long Twist Drill provides a greater overall and working length, allowing deeper bores without extensions; this is beneficial for long‑reach operations and restricted access, while the spiral geometry supports consistent chip evacuation over the full drilling depth. For what is a Twist Drill used? A Twist Drill is mainly applied to the machining of high‑strength materials and larger drill diameters; its shape is easy to re‑grind and it withstands significant loads while providing good centring and cutting behaviour. Which three drill types are there? Common categories include metal drills, wood drills and masonry/concrete drills. Why are Twist Drills sharpened (ausgespitzt)? Sharpening reduces the cross‑edge at the tip of the Twist Drill, which lowers friction and thus requires less feed force; at the same time the tip centres better in the workpiece and improves drilling accuracy. Can a metal Twist Drill be used for wood? A metal drill can be used in wood, but guidance and surface finish will usually be inferior compared with dedicated wood drills; metal drills are easier to re‑grind and typically have less self‑feed than specialised wood drills. For which drilling depths is the Twist Drill most used? A solid bore is commonly executed with a Twist Drill. For diameters up to 20 mm and depths up to 100 mm, the Twist Drill is the most frequently used tool. Is HSS or HSSE better? The general belief that HSSE steels are categorically superior to HSS is incorrect; when choosing, evaluate whether your working conditions justify the higher cost of HSSE for your specific application.

Der extra lange HSS‑G Bohrer kombiniert Präzision, Tieflochfähigkeit und höhere Schnittgeschwindigkeit und reduziert dank geschliffener Geometrie den Kraftaufwand beim Einbohren. Nutzen Sie die extra lange Bauform und die Tieflochspirale für saubere Bohrungen in Stahl und Guss; bei Bedarf berät Metav gern persönlich aus Emmerich. Spiralbohrer von MetavCUT – HSS‑G extra lang Ø 5,2 mm Der Spiralbohrer der Standard Line ist ein extra lang ausgeführter HSS‑G Bohrer für präzise Tieflochbohrungen in legiertem und unlegiertem Stahl sowie Gusseisen. MetavCUT Spiralbohrer Ø 5,2 mm Bauform extra lang für tiefe Bohrungen Geschliffener HSS‑G Schaft für hohe Rundlaufgenauigkeit Spitzenwinkel 135° für harte Werkstoffe DIN 1869 Tieflochspirale für zuverlässigen Späneabtransport Höhere Produktivität durch geschliffene Geometrie Die geschliffene HSS‑G Geometrie ermöglicht ein bis zu 40 % schnelleres Bohren bei deutlich geringerem Kraftaufwand, was insbesondere in der Serienbearbeitung Zeit und Energie spart. Anwender profitieren von einer geringeren Werkzeugbelastung und saubereren Bohrbildern, weil die scharfen Schneiden schneller in das Material eindringen. Dadurch reduziert sich die Wahrscheinlichkeit von Ausrissen und Nacharbeit, was die Effizienz in der Werkstatt messbar erhöht. Passgenaue Eignung für Stahl, Guss und Nichteisenmetalle Dank der Auslegung für legierten und unlegierten Stahl, Gusseisen, Temperguss sowie Nichteisenmetalle eignet sich der Bohrer besonders für anspruchsvolle Metallbearbeitung. Die Kombination aus Tieflochspirale und geschliffener Schneidengeometrie führt zu sauberen Spanwegen und minimiert Verschmutzungen im Bohrloch. Deshalb reduziert sich die Zeit für Entgratungen und Spannmittelwechsel, was den Arbeitsfluss in der Produktion verbessert. Konzeption für tiefe Bohrungen und stabile Führung Die extra lange Bauform mit einer Spirallänge von 210 mm und einer Gesamtlänge von 315 mm ist speziell für tiefe Bohrungen gedacht. Die Norm DIN 1869 garantiert, dass die Spiralgeometrie den Späneabtransport auch unter erschwerten Bedingungen unterstützt. Für maximale Standzeiten empfiehlt sich der Einsatz mit Kühlung und eine stationäre Aufnahme; die geschliffene Ausführung liefert hohe Rundlaufgenauigkeit, ist aber empfindlicher gegenüber starken seitlichen Kräften. Praktische Hinweise für den Einsatz in Werkstatt und Montage Mit einem Durchmesser von 5,2 mm fällt der Bohrer in den Standard‑Bereich und ist für den Einsatz mit Handgeführten Maschinen wie Akkubohrschraubern sowie mit stationären Säulenbohrmaschinen geeignet. Vorbohren ist in der Regel nicht erforderlich; bei besonders harten oder dicken Werkstoffen empfiehlt sich jedoch ein Anpunkten zur Führung. Achten Sie auf passende Schnittgeschwindigkeit und ausreichende Kühlung, um Bruchrisiken zu minimieren und die Standzeit zu verlängern. Empfehlung: Für präzise Tieflochbohrungen empfehlen wir den HSS‑G Extra Lang Bohrer der MetavCUT Standard Line; technische Beratung und Bestellung direkt per E‑Mail an info@metav-werkzeuge.com oder telefonisch unter +49 2822 7131930. Produktmerkmale Artikelnummer: 34052-FDA Hersteller: MetavCUT Bezeichnung: Spiralbohrer Modellserie: Standard Line Fakten Durchmesser: 5,2 mm Gesamtlänge: 315 mm Spirallänge: 210 mm Spitzenwinkel: 135° Verpackungseinheit: 10 Besonderheiten Material: HSS-G Norm: DIN 1869 Schaftausführung: geschliffen Ausführung: extra lang Farbe: blank Für Bohrmaschine: Handbohrmaschine SKU: 34052-FDA UID: 34052-FDA Eignung: legierter und unlegierter Stahl, Gusseisen, Temperguss, Nichteisenmetalle, Hartkunststoff FAQ Welche Werkstoffe lassen sich mit diesem Bohrer bearbeiten? Der MetavCUT Spiralbohrer (Standard Line, SKU 34052-FDA) ist ausgelegt für legierten und unlegierten Stahl, Gusseisen, Temperguss sowie Nichteisenmetalle und Hartkunststoff; die geschliffene Geometrie sorgt für saubere Bohrbilder. Ist der Bohrer für Handgeführte Maschinen geeignet? Ja, der Bohrer mit Ø 5,2 mm gehört zum Standard‑Bereich und kann mit Handgeführten Akkubohrschraubern eingesetzt werden; bei tiefen oder sehr harten Bohrungen wird eine stationäre Maschine und Kühlung empfohlen. Warum ist geschliffen besser als gewalzt? Geschliffene HSS‑G Bohrer haben sehr scharfe Schneiden und hohe Rundlaufgenauigkeit, was präzisere Löcher und saubereren Spanabtransport ermöglicht; der MetavCUT Spiralbohrer bietet dadurch höhere Schnittgeschwindigkeit, allerdings ist die Ausführung empfindlicher gegen seitliche Belastung. Wie tief kann damit gebohrt werden? Die Spirallänge beträgt 210 mm bei einer Gesamtlänge von 315 mm, wodurch sich der Bohrer besonders für tiefe Bohrungen eignet; beachten Sie die Werkstückdicke und setzen Sie bei Bedarf Kühlung ein. Welcher Spitzenwinkel ist verbaut und wofür ist er geeignet? Der Bohrer hat einen Spitzenwinkel von 135°, ideal für härtere Werkstoffe wie Edelstahl und gehärtete Stähle, da der größere Winkel die Anbohrzeit verkürzt und die Führungsstabilität erhöht.

Twist Drill — Twist Drill (Spiralbohrer), Ø 5.5 mm, 135° Point, Bright Finished, Extra Long, HSS‑G, DIN 1869 The Twist Drill is an extra long metalworking Twist Drill designed for deep and precise holes in alloyed and unalloyed Steel, Cast Iron and Hard Plastics when used in a Drilling Machine. Extra long overall length for deep holes CNC ground flutes for high accuracy 135° Point Angle for harder materials HSS‑G Material for sharp, durable cutting edges Bright finished surface for smooth chip evacuation Faster, more powerful drilling in tough materials Dank der HSS‑G Legierung ermöglicht dieser Twist Drill deutlich schnellere Schnitte bei reduziertem Anpressdruck. Entwickelt nach DIN 1869, sorgt der 135° Point Angle für einfacheren Anbohrvorgang in harten Werkstoffen wie Edelstahl oder gehärteten Stählen. Diese Kombination aus Material und Geometrie reduziert Verschleiß und verbessert die Bohrqualität, sodass präzise Bohrlöcher mit sauberem Spanbild erzielt werden können. Reach deep or hard-to-access positions with extra length Die Extra‑Long Ausführung mit einer Overall Length von 330 mm und einer Spiral Length von 225 mm ermöglicht Bohrungen in größeren Tiefen und an schwer zugänglichen Stellen. Der vollständig geschliffene Schaft und die geschliffenen Spannuten garantieren hohe Rundlaufgenauigkeit und saubere Bohrbilder, was speziell bei Metallbearbeitung in Werkzeugbau und Instandhaltung den Unterschied macht. “Fully Ground” bedeutet, dass die Geometrie durch CNC‑Schliff erzeugt wird, was schärfere Kanten und bessere Präzision zur Folge hat. Recommended use and handling for reliable results Für den Einsatz in stationären Drilling Machines oder handgeführten Bohrmaschinen ist eine kontrollierte Kühlung und stabile Werkstückspannung wichtig, da geschliffene HSS‑Bohrer sehr scharf, aber spröder sein können. Anwender sollten den Twist Drill mit moderater Vorschubkraft und geeigneter Kühlschmierstoffzufuhr verwenden, um Bruchrisiken zu minimieren und die Standzeit zu erhöhen. Die Ausführung eignet sich besonders für professionelle Anwender in Werkstätten und Fertigungslinien. Strong recommendation from MetavCUT: For deep metal drilling choose this extra long Twist Drill — METAV Werkzeuge offers expert consultation to ensure the right tool for your task. Contact METAV Werkzeuge for personalised support via eMail: info@metav-werkzeuge.com, Phone: +49 2822 7131930, WhatsApp: +49 170 2837271 Technical Specifications for precise deep metal drilling Designation: Twist Drill Brand: MetavCUT SKU: 34055-FDA Diameter: 5.5 mm Overall Length: 330 mm Spiral Length: 225 mm Point Angle: 135° Material: HSS‑G Execution: Extra Long Shaft Execution: Fully Ground Colour: Bright Finished Type: For Drilling Machine Norm: DIN 1869 Model Series: Standard Line Application: Drills for Metal Packaging Unit: 10 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials can I drill with the Twist Drill by MetavCUT and which machines suit it best? The MetavCUT Twist Drill is optimised for Metal machining and performs well in Alloyed and Unalloyed Steel, Cast Iron and Hard Plastics when used in a suitable Drilling Machine. For best results use steady clamping and coolant to maintain tool life. For what is a Twist Drill mainly used? A Twist Drill is primarily applied to the machining of highly stressed materials and larger drill diameters. Its shape allows relatively simple resharpening and it withstands high loads, making it suitable for demanding metalworking tasks. Which three drill types exist? The three main drill types are Metal Drill, Wood Drill and Stone/Concrete Drill.

Twist Drill — HSS-G Twist Drill, 5 mm, 135° tip, Extra Long, Bright Finished, Fully Ground Shank, DIN 1869 The Twist Drill is an extra long HSS-G drill for Drilling Machines, engineered for deep metal drilling and precision holes in demanding workshop applications. Extra long design for deep drilling HSS-G ground geometry for precise holes 135° tip angle for hard materials Fully ground shank for high runout accuracy Conforms to DIN 1869 for deep-hole applications Engineered for deep metal drilling and higher throughput The Twist Drill is manufactured in HSS-G quality and designed as an extra long tool to reach deeper bore depths than standard bits. This geometry reduces the need for extensions or multi-step drilling, enabling efficient processing of metal components. The combination of ground flute geometry and optimized point form results in up to 40% faster drilling and requires about 50% less feed force, which directly increases productivity and reduces operator fatigue. Precise cutting geometry for tough materials With a 135° tip angle and CNC-ground flutes, this HSS-G bit is tailored to start cleanly in harder materials and maintain concentricity during the cut. The fully ground shank and sharp cutting edges provide excellent runout accuracy and produce clean, burr-reduced holes. Conformance to DIN 1869 signals suitability for deep-hole tasks and use in alloyed and unalloyed steels, grey cast iron, sintered materials and hard plastics when appropriate coolant and speeds are used. Compatibility with drilling machines and usage recommendations Designed for use in a Drilling Machine, the bright finished surface and ground shank simplify clamping and alignment. Due to the grinding process (HSS-G), the tool can be more brittle than rolled types; therefore stationary drilling or proper clamping with coolant is recommended to avoid breakage. Operators will benefit from the bit’s behavior under load: reduced thrust makes handling easier and improves hole quality in serial or repair work. Ideal users and application contexts Metalworking professionals, maintenance technicians and toolroom operators will find this drill especially useful where deep, precise holes in metal are required. The Standard Line model series targets workshops that need reliable, repeatable performance rather than single-use convenience. The extra length and HSS-G construction make it a practical choice for repair jobs, pattern making and production tasks where access is limited. Strong recommendation: For demanding deep-hole metalwork choose the MetavCUT HSS-G Extra Long Twist Drill for reliable penetration and consistent hole quality — for personal technical advice or to confirm suitability for a specific application please contact METAV Werkzeuge directly at info@metav-werkzeuge.com, by phone +49 2822 7131930 or via WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 34050-FDA Diameter: 5 mm Tip Angle: 135° Material: HSS-G Execution: extra long Colour: bright finished Spiral Length: 210 mm Total Length: 315 mm Shank Execution: fully ground For Drilling Machine: Drilling Machine Model Series: Standard Line Application: Drills for metal Norm: DIN 1869 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill from MetavCUT best used for? The MetavCUT Twist Drill is intended primarily for deep-hole drilling and the machining of high-strength and difficult-to-cut metals; it excels in tasks requiring long reach and consistent hole quality under workshop conditions. Can the MetavCUT Twist Drill be used in a handheld drill? While the MetavCUT Twist Drill can physically be clamped in portable equipment, its HSS-G ground construction and extra length make it best suited to stable Drilling Machines or well-supported setups to minimize the risk of breakage. For what is a Twist Drill used? A Twist Drill is mainly applied for machining high-strength materials and large bore diameters. Its shape is easy to grind and withstands higher loads. Which three drill types exist? The three primary drill types are metal drills, wood drills and stone/concrete drills. Why are twist drills pointed? Pointing reduces the cross-cutting edge at the tip of the Twist Drill. By pointing, friction forces are significantly decreased and lower feed forces are required, while the drill tip centers more precisely in the workpiece. Can a Twist Drill be used to drill wood? A metal Twist Drill can be used in wood but typically provides inferior guidance and a less clean finish than dedicated wood drills. Metal bits are easier to resharpen and have less self-feed tendency. At which depths is the Twist Drill the most used tool? Solid drilling with a Twist Drill is common. For diameters up to 20 mm and drilling depths up to 100 mm, the Twist Drill is the most frequently used tool. What is better, HSS or HSSE? The general belief that HSSE steels are always superior to HSS is incorrect. Evaluate working conditions carefully to determine whether the higher cost of HSSE is justified.

Twist Drill — 6.5 mm, 135° Point Angle, Extra Long, Bright Finished, HSS‑G, DIN 1869 The Twist Drill is an extra‑long HSS‑G drill designed for deep metal drilling with a 135° point angle and a bright finished, fully ground shank for high precision in demanding machining tasks. Extra‑long design for deep bore reach 6.5 mm Diameter with 235 mm Spiral Length 135° Point Angle for harder materials Fully ground (HSS‑G) for high runout accuracy Complies with DIN 1869 for demanding conditions Durable HSS‑G construction for precise metalwork The drill is made from HSS‑G, a high‑speed steel that is CNC‑ground to achieve sharp cutting edges and excellent roundness. This fully ground geometry reduces vibration and produces cleaner holes in alloys and hard materials. For users this means fewer reworks and better repeatability when machining components that require tight tolerances. Extra‑long geometry solves deep drilling challenges With an extra‑long overall length of 350 mm and a spiral (flute) length of 235 mm, this tool reaches deeper bore positions where standard drills cannot. The elongated design allows comfortable access in hard‑to‑reach setups and reduces the need for extensions. The 135° point angle shortens entry time in tougher steels and improves centring when starting a hole. Performance advantages and recommended machining practice Compared with standard HSS tools, the ground HSS design can deliver up to 40% faster drilling and requires less axial force, improving operator comfort and machine load. The Twist Drill by MetavCUT is intended primarily for drilling legiertem und unlegiertem Stahl, Gussstahl, Gusseisen, Nichteisenmetalle and hard plastics; use adequate coolant and reduced feed rates at greater depths to minimise breakage risk and extend tool life. Who benefits and how to get support Manufacturers, toolrooms and maintenance teams that demand long reach and high precision will find this Twist Drill particularly suitable. For stationary or machine‑based work, the bright finish and precise geometry ensure consistent hole quality. If uncertain whether this tool meets specific requirements or for complementary technical data, METAV Werkzeuge offers expert advice and application support. Contact METAV Werkzeuge for customised recommendations and assistance with feed, speed and coolant selection. I recommend the MetavCUT extra‑long HSS‑G Twist Drill for any deep metal drilling task that requires precision and enhanced tool life — for personalised advice contact METAV Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930; WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 34065-FDA Diameter: 6.5 mm Point angle: 135° Type / Execution: Extra long Finish / Colour: Bright finished Spiral length (Flute length): 235 mm Overall length: 350 mm Shank execution: Fully ground Material: HSS‑G Applicable machines: Drilling Machine (Hand drill suitable with precautions) Application: Drills for metal Model series: Standard Line Standard / Norm: DIN 1869 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill used for and which materials suit it best? The Twist Drill from MetavCUT (Twist Drill) is mainly used for machining high‑strength materials and larger hole diameters; it is especially suitable for alloyed and unalloyed steel, cast steel, cast iron, non‑ferrous metals and hard plastics thanks to its HSS‑G composition and ground geometry. Can the MetavCUT Twist Drill be used for deep holes and what makes it suitable? Yes, the MetavCUT Twist Drill is designed for deep bores; its extra‑long overall length and a 235 mm spiral length, combined with the DIN 1869 Tieflochspirale, make it ideal for bore depths and difficult access situations. For what is a Twist Drill used? A Twist Drill is primarily applied when machining high‑strength materials and large hole diameters. Its shape allows easy resharpening and the ground geometry endures substantial loads, making it suitable for demanding metalworking. Which 3 drill types are there? Commonly distinguished drill types are: Metal drill (Metal drill), Wood drill (Wood drill), and Masonry/Concrete drill (Stone/Concrete drill). Why are Twist Drills pointed? Pointing reduces the cross‑edge at the drill tip; by pointing the Twist Drill the friction forces at the tip are substantially lowered, which requires less feed force and improves centring of the drill in the workpiece. Can a Twist Drill be used to drill wood? A metal Twist Drill can be used in wood but guidance and finish are inferior compared with dedicated wood drills. The MetavCUT Twist Drill can cut wood, yet results are less clean and the tool may have more tendency to pull itself in. For which depths is the Twist Drill most commonly used? A through hole in solid material is commonly executed with a Twist Drill. For diameters up to 20 mm and drilling depths up to 100 mm, the Twist Drill is the most frequently used tool. What is better, HSS or HSSE? The general belief that HSSE steels are universally superior to HSS is incorrect. Evaluate whether your working conditions justify the higher purchase cost of HSSE; for many applications HSS‑G (ground HSS) as used in the MetavCUT Twist Drill offers an optimal balance of performance and economy.

Twist Drill — Extra Long HSS‑G Twist Drill for Drilling Machine, Ø 6 mm, 135°, Bright Finished, DIN 1869 The Twist Drill is an extra long HSS‑G drill for metalworking, designed for deep holes and hard materials and optimised for use in a Drilling Machine. Extra long design for deep holes 135° point angle for hard materials HSS‑G ground flutes for precise, clean holes Fully ground shank for high concentricity DIN 1869 compliant for deep‑hole applications Precise metal cutting through ground HSS‑G construction The extra long Twist Drill features a HSS‑G (ground high‑speed steel) geometry that produces very sharp cutting edges and a high degree of precision. Grinding the flutes instead of rolling yields improved Rundlaufgenauigkeit and cleaner hole surfaces, which reduces the need for rework. This construction also allows for faster drilling with lower feed forces compared to conventional HSS designs. Use of coolant and appropriate spindle speeds preserves the cutting edge and extends service intervals. Designed for deep and difficult access drilling in metals With an overall length of 330 mm and a spiral length of 225 mm, this extra long design meets the demands of deep bore operations. The 135° point angle makes the bit particularly suitable for harder materials such as alloyed and unalloyed steel and cast iron, where a larger point angle shortens initial cutting time. Conforming to DIN 1869 for deep‑hole capability, the geometry manages chip evacuation under challenging conditions, helping to avoid clogging during extended bores. Suited for workshops, toolrooms and maintenance operations The Twist Drill by MetavCUT is intended for professional metalworkers, maintenance teams and toolroom operators who require reliable deep‑hole performance. In a Drilling Machine it excels at producing accurate cylindrical holes in components, and its design is compatible with stationary setups where coolant can be applied. The bit’s characteristics make it especially useful when precision and repeatability matter, for sample preparation, pattern making or repair work. Handling recommendations to maximise lifetime and safety Because ground HSS can be more brittle than rolled alternatives, correct feed and cooling are essential: moderate feed rates, continuous cooling and firm clamping are recommended to avoid breakage. The fully ground shank improves runout and grip in the chuck, reducing vibration and improving hole quality. If re‑sharpening is required, the ground geometry permits precise reconditioning; however, rework should be done by experienced staff or in a tool shop to retain the original cutting geometry. Prefer MetavCUT quality for deep metal drilling — for technical advice or to confirm suitability contact METAV Werkzeuge by eMail at info@metav-werkzeuge.com, by phone at +49 2822 7131930 or via WhatsApp at +49 170 2837271 Technical Information Designation: Twist Drill Brand: MetavCUT SKU: 34060-FDA Diameter: 6 mm Point Angle: 135° Execution: Extra long Colour: Bright finished For Drilling Machine: Drilling Machine Spiral Length: 225 mm Overall Length: 330 mm Shank Finish: Fully ground Model Series: Standard Line Material: HSS‑G Standard: DIN 1869 Application: Drills for metal Packaging unit: 10 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials is the MetavCUT Twist Drill (Drill for Metal) best suited for? The MetavCUT Twist Drill (Drill for Metal) is optimised for a range of metals: alloyed and unalloyed steel, cast steel, cast iron and non‑ferrous metals. Its 135° point angle and HSS‑G construction make it particularly effective when machining harder workpieces. Can the MetavCUT Twist Drill be used in a handheld drill or is it made for machines? The MetavCUT Twist Drill is specified for use in a Drilling Machine for best results; while it can be fitted to powerful hand drills, performance and service life are maximised in stationary equipment with proper clamping and coolant. For what is a Twist Drill used? The Twist Drill is mainly applied when machining high‑strength materials and larger bore diameters. Its shape allows straightforward re‑grinding and it withstands higher loads, making it suitable for demanding metalwork. Which three types of drill are there? There are three common drill categories: Metal drills, Wood drills, and Stone/Concrete drills. Why are Twist Drills point sharpened? Point sharpening reduces the cross‑cut at the tip of the Twist Drill, which lowers friction and therefore reduces the required feed force; it also improves the drill’s centring in the workpiece for more accurate holes. Can a Twist Drill be used to drill wood? A metal Twist Drill can be used in wood, but guidance and surface finish are usually inferior compared to purpose‑made wood drills; metal bits are easier to re‑sharpen and typically show less self‑feeding. For which drilling depths is the Twist Drill most commonly used? Twist Drills are the standard choice for through holes and solid material drilling. For diameters up to 20 mm and depths up to 100 mm a Twist Drill is often the preferred tool. Is HSS or HSSE better for my application? The idea that HSSE is categorically superior to HSS is not universally correct. Evaluate whether your working conditions justify the higher cost of HSSE; for many applications a well‑made HSS‑G Twist Drill from MetavCUT offers an excellent balance of performance and economy. If you are unsure whether this Twist Drill meets your exact requirements or need additional technical data, METAV Werkzeuge offers comprehensive, competent advice — contact us at info@metav-werkzeuge.com, call +49 2822 7131930 or message via WhatsApp +49 170 2837271.

Twist Drill (Drill Bit) — MetavCUT Extra Long HSS‑G, 7.5 mm, 135° Point Angle, Bright Finished, Fully Ground, DIN 1869 The Twist Drill by MetavCUT is an extra‑long HSS‑G drill bit designed for deep metal drilling in drilling machines, combining increased reach with precise, ground geometry for reliable industrial use. Extra‑long design for deep hole drilling HSS‑G material for higher cutting performance 135° Point Angle optimized for hard metals Fully ground shank for excellent concentricity Conforms to DIN 1869 for demanding conditions Engineered reach and reliability for deep drilling This extra‑long Twist Drill delivers extended reach where standard lengths fall short. The increased Overall Length and Spiral Length make it suitable for deep Holes and hard‑to‑access bore positions, reducing the need for extensions or special fixtures. Because the Flute Geometry is produced by CNC grinding, the bit offers consistently sharp cutting edges and improved chip evacuation, which helps maintain cutting performance over longer penetrations and under higher loads. Ground geometry for precise, clean holes The Fully Ground HSS‑G construction results in very accurate concentricity and sharp cutting lips, producing cleaner bores in metal. A 135° Point Angle reduces walking and spreads cutting forces for tougher materials such as alloyed and unalloyed steels. For users, this means fewer re‑drills, better hole quality and improved fitment for subsequent assembly operations. Use with appropriate coolant and steady feed to avoid brittle breakage tendencies common to ground HSS tools. Material choice and what it means for performance Constructed from HSS‑G, this bit balances hardness and wear resistance with the grindability required for precision tools. HSS‑G is particularly suited to metalworking tasks—casting, steel, sintered materials and certain plastics—where a sharp, ground flute profile improves hole finish. For those less familiar: HSS‑G indicates a High Speed Steel tool that has been ground (G) rather than roll‑formed, giving superior edge geometry and surface finish at the expense of slightly higher brittleness. Recommended use cases and handling advice Best results are achieved when the bit is used in a suitable Drilling Machine with stable clamping, controlled feed and coolant. The extra length is designed for deep bores up to substantial depths while preserving accuracy; avoid excessive side loads and use reduced speeds for very hard materials. When regrinding is necessary, the ground geometry allows relatively simple resharpening, but caution is advised to maintain the correct Point Angle and lip geometry to preserve centring and cutting behaviour. Who benefits from this tool and why This tool is aimed at professional workshops and industrial fabricators who require reliable deep drilling in metals. The combination of DIN 1869 compliance, fully ground shank and extra‑long design makes it a practical choice for machinists tackling components with recessed or hard‑to‑reach bore locations. For users seeking cleaner holes and consistent tool life in challenging materials, the HSS‑G extra‑long design provides a measurable advantage. Strong recommendation: For demanding metalworking applications choose the MetavCUT extra‑long HSS‑G Twist Drill for superior reach and hole quality — METAV Werkzeuge offers comprehensive expert advice and technical support by email at info@metav-werkzeuge.com, by phone at +49 2822 7131930 or via WhatsApp at +49 170 2837271 if additional data or application guidance is required Technical Information Designation: Twist Drill Brand: MetavCUT SKU: 34075-FDA Diameter: 7.5 mm Overall Length: 370 mm Spiral Length: 250 mm Point Angle: 135° Material: HSS‑G Standard: DIN 1869 Execution: Extra long Finish: Bright finished Shank: Fully ground Model Series: Standard Line Suitable For: Drilling Machine Applications: Drills for metal Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill used for and which materials suit it best? The MetavCUT Twist Drill (drill bit) is primarily used for drilling in metal; it is especially effective on alloyed and unalloyed steel, cast iron, sintered metals, temper cast and non‑ferrous metals, as well as hard plastics where a precise bore is required. Which three main drill types exist? The primary drill categories are metal drills, wood drills and stone/concrete drills, covering the typical material families and tool geometries needed for different substrates. For what purpose are twist drills mainly used? Twist Drills are mainly applied to machining high‑strength materials and larger drill diameters; their form is easy to regrind and they withstand higher loads while maintaining hole quality. Why are twist drills pointed (what is the purpose of the point)? Pointing reduces the secondary cutting edge at the tip; by resharpening the point, friction is lowered, which reduces required feed forces and improves centring of the tip in the workpiece for more accurate starts. Can the MetavCUT Twist Drill be used to drill wood? A metal‑grade twist drill can be used in wood, but guidance and surface finish are generally inferior compared with dedicated wood bits. The metal bit is easier to resharpen and has lower self‑feeding tendency. At which drilling depths is the twist drill most commonly used? Solid hole drilling is typically performed with a twist drill. For diameters up to about 20 mm and depths up to around 100 mm, the twist drill is the most frequently used tool. What is better, HSS or HSSE? The common belief that HSSE is always superior to HSS is not universally true. Evaluate working conditions carefully to determine whether the higher cost of HSSE is justified for your application.

Profitieren Sie von der Kombination aus schneller Schneidgeometrie und extra langer Bauform: Der geschliffene HSS-G Spiralbohrer liefert präzise, saubere Bohrungen in legiertem und unlegiertem Stahl, während die Norm DIN 1869 Verlässlichkeit bei tiefen Bohrungen sicherstellt. Bestellen Sie den Bohrer bequem direkt bei Metav und lassen Sie sich bei technischen Fragen von unserer Beratung unterstützen. Spiralbohrer 34070-FDA — extra lang, HSS-G Der Spiralbohrer 34070-FDA ist ein extra langer HSS-G-Bohrer für tiefe Metallbohrungen mit hoher Rundlaufgenauigkeit. Spiralbohrer «34070-FDA» von MetavCUT HSS-G geschliffen für präzise Metallbohrungen Extra lang: Gesamtlänge 370 mm, Spirallänge 250 mm Spitzenwinkel 135° für harte Werkstoffe Norm DIN 1869, Verpackungseinheit 10 Tiefe Bohrungen mit geringem Kraftaufwand für produktive Werkstätten Der geschliffene HSS-G Bohrer wurde für tiefe Bohrungen entwickelt und bietet durch die längere Arbeitslänge echte Praxisvorteile bei schwer zugänglichen Stellen. Durch die geschliffene Geometrie reduziert sich die erforderliche Anpresskraft um bis zu 50 %, was die Belastung von Handbohrmaschine und Anwender verringert. Gleichzeitig ermöglicht die optimierte Spanführung saubere Bohrbilder und verkürzt die Bearbeitungszeit um bis zu 40 %. Diese Kombination erhöht die Effizienz bei Reparatur- und Instandsetzungsarbeiten erheblich. Präzision und Materialverträglichkeit für anspruchsvolle Werkstoffe Mit einem Spitzenwinkel von 135° dringt der Bohrer kontrolliert in härtere Werkstoffe ein und eignet sich für legierten sowie unlegierten Stahl bis 1000 N/mm². Die geschliffene Schaftausführung sorgt für hohen Rundlauf und exakte Bohrungen, ideal wenn Maßhaltigkeit zählt. Für beste Ergebnisse empfiehlt sich das Anpunkten vor dem Bohren und der Einsatz von Kühlschmierstoff bei zähen Materialen, um Lebensdauer und Genauigkeit weiter zu steigern. Einsatzbereich und Anwendernutzen für Werkstatt und Montage Der Bohrer fällt in den Standard-Bereich für Durchmesser und ist besonders geeignet für den Einsatz in Handbohrmaschine sowie stationären Säulenbohrmaschinen. Anwender profitieren von der Extra-Länge bei tiefen Bohrungen oder bei Arbeiten an langen Bauteilen. Die Spirallänge 250 mm ermöglicht effiziente Spänetransport bei moderaten Tiefen; dennoch sind bei sehr tiefen Sacklochbohrungen zusätzliche Maßnahmen wie Vorschubkontrolle und Kühlung empfohlen. Hinweise zur Handhabung und Lagerung für lange Standzeiten Da geschliffene HSS-G Werkzeuge eine sehr scharfe Schneide bieten, sollten Stöße und Verkantungen vermieden werden, um Bruchrisiken zu minimieren. Bei stationärem Einsatz und kontrollierter Kühlung entfaltet der Bohrer sein volles Potenzial. Die Blank-Oberfläche verlangt keine besondere Oberflächenbehandlung, jedoch schützt sachgerechte Lagerung vor Korrosion und mechanischer Beschädigung, wodurch sich die Lebensdauer merklich verlängert. Greifen Sie auf den geschliffenen HSS-G Spiralbohrer von MetavCUT zurück und bestellen Sie über Metav; bei offenen Fragen erreichen Sie unsere Techniker per eMail info@metav-werkzeuge.com oder telefonisch +49 2822 7131930 Produktmerkmale Artikelnummer: 34070-FDA Marke: MetavCUT Serie: Standard Line Bezeichnung: Spiralbohrer Ausführung: extra lang Material: HSS-G Norm: DIN 1869 Farbe: blank Daten Durchmesser: 7 mm Gesamtlänge: 370 mm Spirallänge: 250 mm Spitzenwinkel: 135° Verpackungseinheit: 10 Besonderheiten Schaftausführung: geschliffen Einsatz: Handbohrmaschine HSS-G: geschliffen, hohe Schnittschärfe DIN 1869: Tieflochspirale für extra tiefe Bohrungen FAQ Für welche Materialien ist der Bohrer geeignet? Der MetavCUT Spiralbohrer 34070-FDA aus HSS-G eignet sich für legierten und unlegierten Stahl, Gusseisen, Temperguss sowie Nichteisenmetalle und Hartkunststoff; bei sehr harten Werkstoffen ist auf passende Kühlung zu achten. Kann der Bohrer in einer Handbohrmaschine verwendet werden? Ja, der Spiralbohrer 34070-FDA ist für den Einsatz mit Handbohrmaschine geeignet; für beste Präzision empfiehlt sich Anpunkten und kontrollierter Vorschub. Wie tief kann man mit diesem Bohrer sicher arbeiten? Die extra lange Ausführung mit Gesamtlänge 370 mm und Spirallänge 250 mm ist für tiefe Bohrungen ausgelegt; bei sehr tiefen Sacklöchern sind mehrstufiges Bohren und Kühlung ratsam. Ist dieser Bohrer für Serienfertigung geeignet? Der MetavCUT Spiralbohrer 34070-FDA ist für Werkstatt- und Serienarbeiten im mittleren Umfang geeignet; bei hohen Stückzahlen in gehärtetem Stahl sind Vollhartmetallwerkzeuge wirtschaftlicher. Welche Vorteile hat die geschliffene Ausführung gegenüber gewalzten Bohrern? Geschliffene Spiralbohrer (HSS-G) bieten schärfere Schneiden, bessere Rundlaufgenauigkeit und sauberere Bohrbilder, sind aber empfindlicher gegenüber Stoß- und Kippbelastung und profitieren von stationärem oder gut kontrolliertem Einsatz.

Twist Drill (Drill for Metal) — 8.5 mm, 135° Point Angle, HSS‑G, Extra Long, Bright Finished, Fully Ground Shank, DIN 1869 The Twist Drill from MetavCUT is a precision Drill for Metal designed for deep, accurate holes in hard materials using a fully ground HSS‑G geometry. Extra long for deep and hard-to-reach holes HSS‑G ground design for clean, precise holes 135° point for easier entry in hard materials Fully ground shank for secure chuck grip Compliant with DIN 1869 for deep drilling High-precision geometry for cleaner holes and faster drilling The extra-sharp HSS‑G material and CNC-ground flute geometry deliver consistently precise results when machining steels and non-ferrous metals. This design produces sharp cutting edges and excellent roundness, which means cleaner holes and less rework. Thanks to the optimised geometry, users can achieve up to 40% faster drilling and require up to 50% less feed force compared with conventional HSS bits, reducing operator fatigue and machine load. Built for deep drilling — reliable chip evacuation and stability With an overall length of 390 mm and a spiral length of 265 mm, this Extra Long configuration is intended for deep bore applications where standard lengths fall short. The DIN 1869 specification and the deep-spiral flute aid in effective chip evacuation under extended cutting conditions, lowering the risk of clogging and improving hole quality in deep stacks or confined workpieces. Suitable for demanding metalworking tasks and machine setups The MetavCUT Twist Drill is targeted at machinists, toolroom technicians and maintenance professionals who require robust performance in legated and unlegated steels, cast iron and hard plastics. The Fully Ground Shank ensures accurate clamping and concentricity in chucks and toolholders, while the bright finished surface supports smooth insertion and corrosion resistance during storage. Best practices for longevity and performance To maximise life and performance, operate the bit with appropriate speeds and feeds for the specific metal and use coolant or cutting lubrication for sustained duty cycles; this is especially important given the ground geometry’s brittleness compared with rolled designs. The 135° point angle reduces walking and shortens piercing time in harder alloys such as stainless steel. For optimal results, prefer stationary or well-supported drilling setups and avoid abrupt lateral loads. MetavCUT recommends this Twist Drill for deep, precise metalworking tasks — for tailored technical advice or application support contact METAV Werkzeuge by e-mail at info@metav-werkzeuge.com or call +49 2822 7131930 (WhatsApp +49 170 2837271). Designation: Twist Drill Marke: MetavCUT SKU: 34085-FDA Diameter: 8.5 mm Point Angle: 135° Execution: Extra Long Finish/Colour: Bright Finished Material: HSS‑G Standard: DIN 1869 Spiral Length: 265 mm Overall Length: 390 mm Shank Execution: Fully Ground Application: Drills for Metal Model Series: Standard Line Für Bohrmaschine: Drilling Machine Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill best used for? The MetavCUT Twist Drill (Drill for Metal) is primarily used for machining high-strength materials and larger diameters where durability and precision are required. Its ground HSS‑G geometry is well suited to drilling in alloyed and unalloyed steels, cast iron and hard plastics, and it performs reliably in deep-hole situations. Which three drill types exist? There are three common drill categories: metal drills, wood drills and stone/concrete drills. The MetavCUT Twist Drill belongs to the metal drill group and is designed specifically for metalworking applications. What is a Twist Drill used for? A Twist Drill is mainly applied when working with high‑strength materials and larger bore diameters. Its ground form allows precise sharpening, and it withstands higher loads, making it suitable for drilling alloys, cast steels and hard plastics.

Twist Drill — 8 mm, 135° Tip Angle, Extra Long • Bright Finished • HSS‑G • DIN 1869 The Twist Drill is an extra‑long HSS‑G metal drill for deep, precise holes with a Drilling Machine, optimised for hard materials and demanding shop use. Extra‑long design for deep drilling CNC‑ground HSS‑G for precise, clean holes 135° Tip Angle suited for hard materials Fully ground shank for excellent concentricity Consistent deep-hole performance for demanding metalwork The MetavCUT extra‑long design delivers reliable drilling when access is restricted or when through‑holes must be produced without multiple setups. With a Total Length 390 mm and a Spiral Length 265 mm, this twist drill enables drilling of extended depths while maintaining steady chip evacuation. The elongated geometry reduces the need for extensions or stepped drilling, which saves time in production and lowers fixture complexity. For machinists seeking reproducible deep holes, the geometry is designed to balance stiffness and Reach. Sharp geometry and material for hard, alloyed steels Made from HSS‑G and finished by CNC grinding, the bit combines toughness with cutting precision. The 135° Tip Angle reduces cutting forces in harder materials such as stainless and tempered steels, improving centring and lowering the risk of workpiece deformation. Grinding the Flutes produces a sharp cutting edge and high runout accuracy, which results in cleaner bores and more consistent hole tolerances. For operators less familiar with grind types: CNC grinding means the Flute geometry is cut rather than rolled, giving higher Dimensional Precision at the cost of slightly increased brittleness — therefore cooling and appropriate speeds are recommended. Recommended applications, handling and compatibility This metal drill is intended for drilling in legated and unlegated Steel, Cast Iron, Non‑Ferrous Metals and Hard Plastics under workshop conditions. It is optimised for use in a Drilling Machine and benefits from controlled speeds, steady feed and coolant for prolonged life. The Fully Ground Shank improves clamping concentricity in chucks, reducing runout and vibration. As a practical tip: when working deep, ensure adequate Chip Evacuation and periodic pecking or coolant supply to prevent clogging and premature wear. Choose the MetavCUT Twist Drill for demanding deep metal drilling — for technical advice or to check suitability for a specific application contact METAV Werkzeuge: info@metav-werkzeuge.com • +49 2822 7131930 • WhatsApp +49 170 2837271 Bezeichnung: Twist Drill Marke: MetavCUT Diameter: 8 mm Total Length: 390 mm Spiral Length: 265 mm Tip Angle: 135° Execution: Extra long Colour / Finish: Bright finished Shank: Fully ground Material: HSS‑G Standard: DIN 1869 Application: Drills for metal / for Drilling Machine Model Series: Standard Line Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill best used for? The MetavCUT Twist Drill (metal Twist Drill) is primarily designed for machining high‑strength and alloyed steels and larger bore diameters; its extra‑long design and HSS‑G material make it suitable for deep holes and applications requiring precise hole geometry. Can the MetavCUT Twist Drill be used in a bench or handheld drill? The MetavCUT Twist Drill is optimised for use in a Drilling Machine; it can be used in powerful benchtop machines but, due to its length and ground construction, handheld use is not recommended for safety and accuracy reasons. For what is a Twist Drill used? A Twist Drill is mainly applied when machining high‑strength materials and large bore diameters. Its form allows relatively easy regrinding and it endures higher loads, making it suitable for tough metalworking tasks. Which three drill types exist? Common categories are Metal Drill, Wood Drill and Masonry/Concrete Drill. Why are twist drills pointed? Pointing reduces the cross‑edge at the tip of the twist drill. By pointing, friction forces are significantly lowered so reduced feed forces are required, and the tip centres better in the workpiece. Can you drill wood with a metal twist drill? A metal drill can be used in wood, but guidance is poorer and hole quality is inferior. Metal bits are easier to regrind and have less self‑feed, so results may be acceptable for non‑critical wooden applications. At which drilling depths is the twist drill most used? Twist Drills are the standard tool for through holes and are most commonly used up to diameters of about 20 mm and drilling depths up to 100 mm; extra‑long variants extend that capability for deeper bores. Which is better, HSS or HSSE? The general assumption that HSSE is always superior to HSS is incorrect. Evaluate working conditions carefully to determine whether the higher cost of HSSE is justified for the required application.