HSS-G DIN 1897 Twist Drills – Type N, Extra Short, Bright, 135° Split Point

Twist Drill — Type N Twist Drill, Ø 1.5 mm, 118° tip, Extra Short, Bright finished, HSS‑G, DIN 1897 (MetavCUT) The Twist Drill Type N is an extra‑short, ground HSS‑G drill designed for precise metal drilling in hand Drilling Machines and confined spaces. Extra‑short design for high stability HSS‑G ground for up to 40% faster drilling 118° tip for improved centering on curved surfaces Cylindrical shank for universal chuck compatibility Conforms to DIN 1897 for robust workshop use Greater Stability where Space is Limited The Twist Drill from MetavCUT in Extra Short execution is engineered to minimise bending and breakage when working in tight or thin‑walled components. Its reduced Overall Length and shorter Spiral/Working Length increase Stability and torsional rigidity compared with standard drills, which helps to avoid chatter and tool failure during handheld operations. This design makes the bit particularly suitable for Sheet Metal, Profiles and assemblies where access and clearance are restricted, while the DIN 1897 specification underlines consistent dimensions and interchangeability in workshop environments. Faster Cutting with Lower Feed Effort A ground HSS‑G cutting geometry reduces friction and chip adhesion, enabling up to 40% faster advance rates while requiring approximately 50% less Feed Force than conventional HSS drills. Ground fluting improves the cutting edge sharpness and chip evacuation, so the drill penetrates more efficiently and produces cleaner holes. For users, this translates into shorter cycle times and less operator fatigue when working with alloyed and unalloyed steels, cast materials and hard plastics. Tip Geometry Optimised for Metalwork The Type N spiral is the classic metal‑drill geometry, optimised for a wide range of ferrous materials. The 118° tip balances cutting aggressiveness and centring ability: a moderate point angle eases entry on slightly curved surfaces and helps initial alignment, while still providing good lifetime on steels and non‑ferrous metals. For less experienced users: the tip angle determines how the bit bites into the material — a larger angle yields a blunter point with longer cutting edges, whereas a smaller angle improves penetration and centring. Practical Fit and Typical Applications With a Cylindrical (round) shank the bit fits standard three‑jaw chucks on Hand and Angle Drilling Machines, offering universal usability across common workshop equipment. The construction from HSS‑G makes this short drill ideal for maintenance, mechanical workshops and assembly tasks where repeatable, clean holes in steel, cast iron and non‑ferrous metals are needed. Note that the round shank can be prone to slipping under very high torque loads; for heavy‑duty drivers a hex or reduced shank may be preferable. Highly recommend MetavCUT Twist Drill Type N for precise metalworking tasks — for technical advice or to confirm suitability for a specific application contact METAV Werkzeuge: 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp +49 170 2837271 Bezeichnung: Twist Drill Marke: MetavCUT SKU: 56015-FDA Durchmesser: 1.5 mm Spitzenwinkel: 118° Typ: Type N Ausführung: Extra Short Farbe / Finish: Bright finished Material: HSS‑G Schaftausführung: Cylindrical Spirallänge: 9 mm Gesamtlänge: 32 mm Norm: DIN 1897 Anwendung: Drills for Metal Modellserie: Standard Line Für Bohrmaschine: Drilling Machine Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials is the Twist Drill by MetavCUT best suited for? The MetavCUT Twist Drill Type N is primarily intended for metalworking: alloyed and unalloyed Steel, Cast Steel, Cast Iron, Sintered Iron, Tempered Castings, non‑ferrous metals and hard plastics. Its HSS‑G composition and normal spiral geometry make it efficient for a broad selection of metallic materials in workshop and maintenance settings. Can the MetavCUT Twist Drill be used in hand and angle drills? Yes, the extra‑short HSS‑G design of the MetavCUT Twist Drill is specifically suitable for Hand and Angle Drilling Machines; the reduced overall length improves control in handheld use and in confined spaces while the Cylindrical shank fits standard three‑jaw chucks. What are Twist Drills used for? Twist Drills are mainly applied to the machining of high‑strength materials and larger hole diameters. Their form is relatively easy to re‑grind and resists significant loads, which makes them suitable for demanding metal drilling tasks. Which 3 drill types exist? The three common drill families are: Metal drills, Wood drills, and Stone/Concrete drills. Why are Twist Drill points sharpened? Point sharpening reduces the size of the cross‑cut at the tip, which significantly lowers friction and therefore the required feed forces. At the same time sharpened points improve centring accuracy in the workpiece. Can a metal drill be used for wood? A metal (Type N) drill can be used in wood, but guidance and finish quality are usually inferior compared with purpose‑made wood drills. Metal drills are easier to re‑grind and typically exhibit lower self‑feed characteristics. For which drilling depths is the Twist Drill most commonly used? Twist Drills are the standard tool for through holes in the solid. For diameters up to 20 mm and drilling depths up to 100 mm, the twist drill is the most frequently used tool. What is better, HSS or HSSE? The general belief that HSSE steels are categorically superior to standard HSS is incorrect. Evaluate the working conditions carefully to decide whether the higher investment in HSSE is justified for the intended application.

Twist Drill — Type N extra short, 2.1 mm, 118°, HSS‑G, Bright Finished, DIN 1897 An extra‑short Twist Drill (Type N) designed for Drilling Machines and Hand Drills, offering a 2.1 mm Diameter and a 118° Tip Angle for precise, low‑force metalworking. Extra‑short HSS‑G Twist Drill for tight spaces 2.1 mm Diameter for precise pilot holes 118° Tip for reliable centering in soft materials Cylindrical Shank fits standard three‑jaw chucks DIN 1897 standard; bright finished for durability Faster Drilling with Less Force and Higher Stability The MetavCUT Type N Twist Drill uses a ground HSS‑G geometry that reduces friction and delivers up to 40% faster drilling compared with conventional HSS tools. This results in lower operator effort and reduced heat build‑up, especially when working with steel and cast materials. The extra short design increases torsional stability and lowers the risk of Breakage, making it particularly suitable for tight setups or thin‑walled components where control is critical. Customers benefit from shorter cycle times and a more consistent Hole Quality. Compact Design That Excels in Confined Workspaces Where access is limited, the extra short length of this Twist Drill provides a clear advantage. Shorter Overall Length and reduced flute length mean improved Rigidity and less Whipping, so holes remain true even when working in awkward positions or with Hand Drills. The Cylindrical Shank allows universal chuck clamping and quick tool changes, which supports efficient workshop workflows and reduces set‑up time for repetitive tasks. Broad Material Compatibility and Clear Application Guidance This Type N Twist Drill is optimized for metalworking: it is suitable for alloyed and unalloyed Steel, Cast Steel, Cast Iron, Sintered Iron, Tempered Iron, Non‑Ferrous Metals and Hard Plastics. For users less familiar with drill types: Type N denotes a Normal Spiral suited for Metal; it is not intended as the first choice for very soft materials like wood where specialist bits offer cleaner guidance. When precise centering is required on curved surfaces, the 118° Tip Angle helps start the Hole with low point‑load and reduced surface wandering. Practical Handling, Sharpening and Durability The HSS‑G Material provides a balance of Hardness and Toughness; it is easy to Regrind, which extends Tool Life and allows maintenance of a sharp Cutting Edge in‑house. The bright finished surface supports corrosion resistance and visual inspection of wear. Because the Shank is smooth and cylindrical, users should ensure correct Chuck Torque and regular inspection to prevent slippage under high loads. For frequent heavy‑duty applications, consider matching drive methods and clamping systems to the task to maximise performance. Who Benefits from This Tool Professionals and hobbyists who require compact, reliable drilling performance in metalworking environments will appreciate the combination of extra rigidity and ease of use. The MetavCUT Type N Twist Drill is particularly suited for workshops doing precision pilot holes, maintenance tasks, and any operation where space constraints or thin materials demand a short, robust cutter. Choose the MetavCUT Type N Twist Drill for precise metal drilling — for expert advice and application support contact METAV Werkzeuge: info@metav-werkzeuge.com | Phone: +49 2822 7131930 | WhatsApp: +49 170 2837271 Designation: Twist Drill Marke: MetavCUT SKU: 56021-FDA Type: Type N Diameter: 2.1 mm Total Length: 38 mm Spiral Length: 12 mm Tip Angle: 118° Material: HSS‑G Shank: Cylindrical Finish: Bright finished Execution: Extra short Application: Drills for Metal Standard: DIN 1897 Series: Standard Line For Drill Machine: Drilling Machine Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill used for? A Twist Drill like the MetavCUT Type N Twist Drill is primarily used for machining high‑strength materials and for larger hole diameters where tool robustness is essential. This design is straightforward to Regrind and endures greater loads, making it suitable for demanding Metalworking operations. Which 3 drill types are there? In practice three common drill categories exist: Metal Drill, Wood Drill and Stone/Concrete Drill. The MetavCUT Type N Twist Drill belongs to the Metal Drill group and is engineered for performance in metallic materials. Can the MetavCUT Type N Twist Drill be used with hand drills? Yes, the MetavCUT Type N Twist Drill is suitable for Hand Drills and Drilling Machines when clamped securely in a compatible Chuck. Its Extra‑short design improves stability under manual operation and reduces the risk of Breakage in confined setups. Why are Twist Drills pointed? Pointing the tip reduces the cross‑cut at the tip, which lowers friction and therefore requires less Feed Force. A well‑sharpened tip also improves Centering and helps the Drill begin the hole cleanly in the workpiece.

Twist Drill (Type N) – 2.2 mm, 118° tip, Extra Short, Bright Finished, HSS‑G, DIN 1897 — MetavCUT The Twist Drill (Type N) is an extra‑short HSS‑G metal drill designed for handheld and angle drilling, offering a 2.2 mm diameter with a 118° tip angle for improved centring and reliable performance in thin materials. Extra‑short design for greater stability HSS‑G material for durable cutting 118° tip improves centring on curved surfaces Cylindrical shank fits standard drill chucks Complies with DIN 1897, Type N spiral Greater stability and faster drilling in metalworking The extra short geometry reduces overhang and increases torsional stiffness, so drilling with less chatter and a lower breakage risk is achievable even under hand‑held conditions. Made from HSS‑G, this bit combines heat‑resistance and toughness so that cuts remain sharp longer; users benefit from up to 40% faster penetration and reduced required feed force compared with standard HSS bits. This makes the tool particularly efficient for working with alloyed and unalloyed steels where consistent, repeatable holes are required. Reliable handling in confined spaces and on portable machines Designed for use with a Drilling Machine and especially suited to Hand Drills and Angle Drills, the bit’s Cylindrical shank ensures compatibility with standard three‑jaw chucks and simple, secure mounting. The short overall length makes accessibility in narrow or recessed areas much easier, allowing clean boreholes in thin sheets and profiles. For professionals and hobbyists who regularly face limited working room, the compact shape reduces operator fatigue and improves control. Tip geometry and spiral type for precise centring The 118° tip angle offers a good balance between cutting aggressiveness and centring behaviour; for softer materials such as aluminium and certain plastics the wider angle helps the drill start cleanly without wandering. As a Type N (normal spiral) configuration, the flute geometry is optimised for metalworking chips evacuation while maintaining a robust cutting lip. An explanation for less experienced users: the tip angle determines how quickly the drill bites into the material and how well it centres on curved or uneven surfaces. Standards, suitability and maintenance benefits Manufactured to DIN 1897 specifications within the Standard Line, this bit is intended for general metal drilling tasks including steel, cast iron and non‑ferrous metals. Its short, robust form is ideal for drilling into thin components like sheet metal and profiles where longer drills would flex. The HSS‑G composition allows economical resharpening, extending service life and lowering lifecycle costs for workshops that maintain their own tooling. We strongly recommend the MetavCUT Twist Drill Type N for precision metalwork; for technical guidance or to confirm suitability for your application, contact METAV Werkzeuge’s expert team by e‑mail at info@metav-werkzeuge.com, by phone at +49 2822 7131930 or via WhatsApp at +49 170 2837271 — METAV Werkzeuge offers comprehensive, competent consultation to help you choose the right tool for the task. Twist Drill Brand: MetavCUT SKU: 56022-FDA Diameter: 2.2 mm Total length: 38 mm Spiral length: 12 mm Tip angle: 118° Type: Type N Execution: extra short Finish/Colour: bright finished Shaft execution: Cylindrical Material: HSS‑G Standard: DIN 1897 For drill machine: Drilling Machine (Hand Drill) Application: Drills for metal Model series: Standard Line Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials is the MetavCUT Twist Drill (Type N) suitable for? The MetavCUT Twist Drill Type N is optimised for metalworking: it performs well in alloyed and unalloyed steels, cast steel, cast iron, sintered iron, malleable iron, non‑ferrous metals and hard plastics; its HSS‑G composition ensures heat resistance and long cutting life when used under appropriate speeds and lubrication. Can the MetavCUT Twist Drill (Type N) be used in a handheld drill? Yes, the MetavCUT Twist Drill Type N with its extra short design and Cylindrical shank is suitable for Hand Drills and Angle Drills; the compact length improves stability and accessibility, though correct clamping in a three‑jaw chuck and suitable drilling parameters are important to avoid slippage. For what are Twist Drills used? Twist Drills are primarily applied to the machining of high‑strength materials and larger hole diameters. Their shape makes them easy to resharpen and able to withstand higher loads; they are commonly used where robustness and repeatable performance are required. Which 3 drill types exist? The three main drill categories are metal drills, wood drills and stone/concrete drills.

Twist Drill — Type N, Ø 2.3 mm, 118° tip, Extra Short, Bright Finished, HSS-G, DIN 1897 (MetavCUT) The Twist Drill Type N is an extra-short HSS-G drill bit designed for precision metal drilling with hand and angle drilling machines. Extra-short design for greater stability High-speed HSS-G for fast metal drilling 118° tip for easier centring on curved surfaces Cylindrical shank fits standard three-jaw chucks Conforms to DIN 1897 for consistent quality Precision and Strength for Metalworking Designed for efficient metal removal, the Twist Drill from MetavCUT combines a HSS-G cutting material with a ground geometry that allows faster penetration and reduced operator effort. The ground HSS geometry reduces required feed force compared with conventional HSS, making drilling smoother and more controlled. This results in fewer deflections and cleaner holes when working in alloyed and unalloyed steels, cast iron, sintered iron and non-ferrous metals. Stable Short-Length Design for Confined Spaces The extra-short execution significantly improves rigidity: a shorter overall and flute length reduces the lever arm and thus the risk of breakage under lateral loads. This makes the bit particularly suitable when access is limited, or when drilling thin-walled components such as sheets and profiles. The compact geometry increases torsional resistance and supports steady drilling in workshop and maintenance applications. Compatibility, Tip Geometry and Practical Effects With a 118° tip angle, the Type N geometry eases centring on slightly curved surfaces and suits softer metals as well as general workshop use. The cylindrical shank fits standard three-jaw chucks, offering universal compatibility with most hand and angle drilling machines. The Type N normal spiral is optimised for metalworking and produces reliable chip removal and hole quality in common ferrous and non-ferrous materials. Who benefits from this Twist Drill Small workshops, maintenance technicians, and hobbyists benefit from the robust construction and versatile application range of this MetavCUT drill. The combination of extra-short length, HSS-G material and conformity to DIN 1897 makes it a practical choice for repetitive metal drilling tasks where stability and hole accuracy are required. METAV Werkzeuge provides expert advice if there is any uncertainty about suitability for a specific application. For precision metal drilling choose the MetavCUT Twist Drill Type N — METAV Werkzeuge offers detailed technical support and personalised advice via info@metav-werkzeuge.com, Tel +49 2822 7131930, WhatsApp +49 170 2837271 Twist Drill Brand: MetavCUT SKU: 56023-FDA Diameter: 2.3 mm Spiral length: 12 mm Overall length: 38 mm Tip angle: 118° Type: Type N Material: HSS-G Execution: Extra short Shaft execution: Cylindrical Finish/Colour: Bright finished Standard: DIN 1897 For use in: Drilling Machine (Handbohrmaschine / angle and hand drills) Model series: Standard Line Application: Drills for metal Packaging unit: 10 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials is the MetavCUT Twist Drill Type N suitable for? The MetavCUT Twist Drill Type N is optimised for metalworking: it is suitable for alloyed and unalloyed Steel, Cast Steel, Cast Iron, Sintered Iron, Non-Ferrous Metals and Hard Plastics; this makes it a reliable choice for workshop and industrial applications. Can the Twist Drill be used in handheld drills? Yes, the MetavCUT Twist Drill Type N with a Cylindrical shank is intended for Hand and Angle Drilling Machines and can be clamped in standard three-jaw chucks; its Extra Short design improves stability in handheld operations. For what is a Twist Drill used? A Twist Drill is mainly applied for machining high-strength materials and larger hole diameters; this form is easy to regrind and withstands higher loads. Which three drill types exist? There are three common drill categories: Metal drill, Wood drill, and Stone/Concrete drill. Why are Twist Drills sharpened (pointed)? The sharpening reduces the cross cutting edge at the tip of the Twist Drill, lowering friction forces and therefore the required feed force while improving tip centring in the workpiece. Can a metal drill be used to drill wood? A metal drill can also be used in wood, but accuracy and guidance are inferior compared with dedicated wood drills; metal drills are easier to regrind and exhibit less self-feeding. For which drilling depths is the Twist Drill most commonly used? A solid hole is typically made with a Twist Drill; for diameters up to 20 mm and drilling depths up to 100 mm, the Twist Drill is the most commonly used tool. Is HSS or HSSE better? The common assumption that HSSE steels are always superior to HSS is not universally true; choose based on actual working conditions to determine whether the higher investment in HSSE is justified.

Twist Drill – Type N extra short HSS‑G (Ø 2.4 mm, 118°, Bright Finished, DIN 1897) by MetavCUT A MetavCUT Twist Drill (Type N) for precise metal drilling with an extra‑short design ideal for hand Drilling Machines. Extra-short HSS-G for enhanced stability Ø 2.4 mm precision for fine metalwork 118° point angle for easy centring Cylindrical shank fits standard chucks Exceptional stability and faster metal machining The extra‑short ground HSS‑G construction delivers noticeably higher rigidity compared with standard lengths. This reduces vibration and breakage risk when working in tight setups and thin materials. Thanks to the ground geometry, machining can be performed up to 40% faster while requiring significantly less axial pressure, which lowers operator fatigue and improves repeatability on metal components. Ideal for confined spaces and hand drilling Designed with a total length of 38 mm and a spiral length of 12 mm, the compact format suits applications where access is limited or where a short overhang is required. The cylindrical shank fits conventional three‑jaw chucks used on hand Drilling Machines, offering universal compatibility and quick tool changes. Conformance to DIN 1897 guarantees dimensional reliability for workshop and maintenance use. Built for metal — versatile in material range As a Type N normal‑spiral bit, this tool is optimised for metalworking tasks. It performs well in alloyed and unalloyed Steel, Cast Steel, Cast Iron, Sintered Iron, Tempered Iron, Non‑Ferrous Metals and Hard Plastics. The 118° point angle improves centring on slightly curved surfaces and helps when machining softer metals such as Aluminium, while the Type N spiral remains the preferred choice for metal drilling operations. Practical advantages for professionals and enthusiasts The short, robust geometry provides higher torsional resistance and a lower tendency to chatter, making it suitable for production, maintenance and committed hobbyists. The ground cutting edges allow economical regrinding and maintenance, extending service life. Note that the cylindrical shank is universally compatible, though under very high torque conditions a different shank form can offer improved anti‑slip behaviour. We recommend the MetavCUT extra‑short HSS‑G Twist Drill for precise metalworking and confined‑space applications — for further technical advice or to ensure the tool meets your specific requirements, METAV Werkzeuge provides competent consultation by eMail at info@metav-werkzeuge.com, by phone at +49 2822 7131930 or via WhatsApp at +49 170 2837271 Twist Drill Brand: MetavCUT SKU: 56024-FDA Diameter: 2.4 mm Total length: 38 mm Spiral length: 12 mm Point angle: 118° Type: Type N Execution: extra short Colour: Bright Finished Shank design: Cylindrical Material: HSS‑G Standard: DIN 1897 Application: Drills for metal Model series: Standard Line For Drilling Machine: Hand Drilling Machine Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill primarily used for? The MetavCUT Twist Drill (Type N) is primarily used for machining high‑strength materials and larger metal diameters. Its extra‑short, ground design is easy to regrind and endures higher loads, making it suitable for robust metalworking tasks. Which three main drill types exist? There are three common drill categories: metal drills, wood drills and stone/concrete drills. The MetavCUT Twist Drill belongs to the metal drill group and is optimised for drilling various metals.

Twist Drill — Type N extra short, Ø 2.5 mm, 118° tip, Bright Finished, HSS‑G, DIN 1897 (MetavCUT) The Twist Drill is an extra short Type N drill designed for metalworking with a 2.5 mm Diameter and a 118° Tip Angle, suitable for Hand Drilling Machines and compact operations. Extra short design for high stability and tight spaces Ground HSS‑G for up to 40% faster drilling Cylindrical Shank for universal chuck compatibility Conforms to DIN 1897 for consistent quality Optimised for metal drilling and thin sheet applications Precise metalworking with higher feed efficiency The extra short design of this Twist Drill delivers noticeably improved Stability and reduced breakage risk when compared with standard-length tools. The Ground HSS‑G cutting geometry reduces required Feed Force and increases Penetration Speed, so holes in alloyed and unalloyed Steel, Cast Iron and Non‑Ferrous Metals are produced more reliably. For users who require controlled drilling in limited access areas, the shortened Overall Length improves handling and reduces vibration while maintaining concentricity. Material advantages and drilling behaviour Manufactured from HSS‑G, the tool offers robust wear resistance and edge retention for demanding metal operations. The 118° Tip Angle favours softer metals and provides easier centring on curved surfaces, while the classic Type N flute geometry is optimised for chip evacuation in metalworking. The Cylindrical Shank ensures universal compatibility with standard three‑jaw chucks, although users should note increased slippage risk under very high torque compared with hex or triangular shanks. Ideal applications and target users This drill is aimed at professionals and hobbyists working with sheet metal, profile sections and machine components where compact tooling and precise results matter. It excels in Hand Drilling Machine use and is suitable for drilling into Steel, Cast Steel, Sintered Iron and various Hard Plastics. For projects requiring repeatable and centred holes in thin materials or confined setups, the shortened geometry provides a clear advantage and reduces the chance of deflection. Handling tips and what makes this drill stand out To achieve best results, use moderate cutting speeds and steady feed; lubrication is recommended for alloyed steels to extend tool life. The Extra Short format reduces bending moments and is therefore less prone to runout, while the DIN 1897 conformity guarantees dimensional and geometric consistency. The product’s Bright Finished surface supports easy identification and corrosion resistance during storage. For precision metal drilling, choose the MetavCUT Twist Drill Type N with 2.5 mm Diameter and extra short design — METAV Werkzeuge provides expert technical advice and support: info@metav-werkzeuge.com, Tel +49 2822 7131930, WhatsApp +49 170 2837271 Designation: Twist Drill (Twist Drill / Spiralbohrer) Brand: MetavCUT SKU: 56025-FDA Diameter: 2.5 mm Tip Angle: 118° Type: Type N Material: HSS‑G Execution: Extra short Colour / Finish: Bright Finished Shank Design: Cylindrical Spiral Length: 14 mm Overall Length: 43 mm Series: Standard Line Application: Drills for Metal For use with: Drilling Machine (Hand Drilling Machine) Standard: DIN 1897 Additional note: Extra short length increases stability and is suitable for thin materials and tight spaces Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill Type N mainly used for? The MetavCUT Twist Drill Type N is primarily applied to the machining of high‑strength workpieces and larger hole diameters; its robust geometry and grind make it suitable for alloyed and unalloyed steels, cast materials and hard plastics while resisting higher loads. Which three drill types exist? Commonly distinguished drill types are Metal Drills, Wood Drills and Stone/Concrete Drills; the MetavCUT Twist Drill Type N belongs to the Metal Drill category and is tailored to metalworking tasks. Why are Twist Drills sharpened at the point? The point sharpening reduces the cross‑edge at the tip of the Twist Drill, which lowers friction and required feed forces while improving centring accuracy in the Workpiece. Can a metal Twist Drill be used for wood? A Metal Drill can be used in Wood, but guidance and finish are usually inferior compared with dedicated Wood Drills; however, Metal Drills are easier to re‑sharpen and have lower self‑feeding tendency. For which drilling depths is the Twist Drill most used? A full‑bore operation is commonly executed with a Twist Drill. For diameters up to 20 mm and depths up to 100 mm, the Twist Drill is the most frequently used tool.

Twist Drill — Type N extra-short HSS‑G drill, Ø 2.6 mm, 118° point, bright finished, cylindrical shank, DIN 1897 The Twist Drill Type N is an extra-short HSS‑G drill bit designed for precise metalworking with hand Drilling Machines and tight-space applications. Extra-short design for higher stability HSS‑G material for faster cutting 118° point angle for improved centring Cylindrical shank fits standard three-jaw chucks Conforms to DIN 1897 for consistent dimensions Precision and stability for metalworking that matters This extra-short Twist Drill from MetavCUT is engineered to reduce flex and breakage when working with alloyed and unalloyed steels. The shortened overall length and reduced flute/working length increase stability and torsional resistance, which directly lowers the risk of snap-off during manual drilling. For users who require predictable, repeatable holes in components, the compact geometry delivers a noticeable increase in control and operator confidence. Easier centring and reliable start on curved or soft surfaces With a 118° point angle, the Twist Drill provides gentler penetration and improved centring on softer materials such as aluminium or wood-like substrates when used incidentally. This geometry reduces the tendency to wander on crowned or irregular surfaces, so holes start cleanly with less hand correction. The result is a neater entry hole and less rework, which is particularly valuable for time-sensitive fabrication or assembly tasks. Faster cutting with lower feed force thanks to HSS‑G The HSS‑G construction of this MetavCUT Twist Drill combines high-speed steel properties with ground geometry to enable up to 40% faster drilling and approximately 50% lower feed force compared with conventional HSS bits. This means less operator fatigue on hand-held machines and reduced demands on light-duty motor units, while maintaining performance in materials such as cast iron, tempered steel, non‑ferrous metals and engineering plastics. Universal compatibility and practical use cases Equipped with a cylindrical shank, the bit is universally compatible with standard three-jaw chucks, making it suitable for most bench and hand Drilling Machines. The DIN 1897 designation ensures dimensional conformity for consistent clamping and interchangeability. This Twist Drill is particularly suitable for thin-walled constructions like sheet metal, profiles and assemblies where space constraints demand a short tool that still offers robust cutting action. Who benefits from this Twist Drill Workshop professionals and maintenance technicians who need a reliable, compact metal drill for hand-held or angle drilling will value the MetavCUT extra-short Twist Drill. It is designed for users who prioritise tool stability, quick chip evacuation and consistent hole quality over long overhangs. The product is also suitable for smaller production runs and repair jobs where machine access is limited. Strong recommendation: Choose the MetavCUT extra-short Twist Drill Type N for demanding metal drilling tasks and contact METAV Werkzeuge for expert guidance — Email: info@metav-werkzeuge.com — Phone: +49 2822 7131930 — WhatsApp: +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 56026-FDA Diameter: 2.6 mm Point Angle: 118° Type: Type N Material: HSS‑G Standard: DIN 1897 Execution: Extra short Colour: Bright finished Shank Design: Cylindrical Spiral Length: 14 mm Total Length: 43 mm Intended For: Drills for metal / Hand Drilling Machine Model Series: Standard Line Shaft Finish: Zylinder (Cylindrical shank) Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ For what is the Twist Drill from MetavCUT used? The MetavCUT Twist Drill Type N is primarily used for drilling in high‑strength materials and larger diameters; its extra-short form is ideal for stable operation and for machining alloyed and unalloyed steel, cast iron, sintered iron, non‑ferrous metals and hard plastics. Which three drill types are commonly distinguished? Three common drill types are metal drills, wood drills and stone/concrete drills; the MetavCUT Twist Drill belongs to the metal drill category designed for metalworking applications. Why are Twist Drills sharpened at the tip? The tip sharpening of the MetavCUT Twist Drill reduces the cross‑cut at the tip, lowering friction and therefore the required feed force, while improving centring of the tip in the workpiece. Can the MetavCUT Twist Drill be used to drill wood? A metal Twist Drill from MetavCUT can be used in wood, but guidance and finish are inferior compared with dedicated wood drills; however, metal drills are easier to resharpen and show less self‑feed tendency. At which drilling depths is the Twist Drill most commonly used? Spiral or Twist Drills are most commonly used for through drilling; for diameter ranges up to 20 mm and drilling depths up to 100 mm, the Twist Drill is the prevalent tool for conventional drilling tasks. What is better, HSS or HSSE? The general belief that HSSE steels are always superior to HSS is incorrect; evaluate working conditions carefully to decide whether the higher cost of HSSE is justified for your MetavCUT Twist Drill application.

Twist Drill — Type N extra short, Ø 2.7 mm, 118° point angle, Bright finished, HSS‑G, DIN 1897 (MetavCUT) The Twist Drill Type N is a compact metalworking drill designed for Hand Drilling Machines to deliver stable, precise holes in confined or thin-walled workpieces. Extra short geometry improves rigidity HSS‑G material for durable metal drilling 118° point angle for reliable centring Cylindrical shank fits standard chucks DIN 1897 compliant for workshop use Precision in confined spaces increases process reliability When working where clearance is limited, the extra short geometry significantly improves stability and reduces the risk of breakage. The reduced overall length and shorter flute make the drill easier to control in thin sheets and profiles, while the compact form factor also helps when using angled or hand-held drilling equipment. This design is particularly useful for operations that demand clean, repeatable holes without excess vibration. Faster and less forceful drilling for metalworking efficiency Engineered from HSS‑G, this Twist Drill offers a ground cutting geometry that can achieve up to 40% faster feed rates and requires around 50% less thrust compared to conventional HSS drills. That means less operator fatigue and shorter cycle times when drilling alloyed and unalloyed steels, cast materials and hard plastics. The result is improved productivity and more consistent hole quality in metalworking environments. Universal mounting and dependable handling reduce setup time A cylindrical shank ensures straightforward clamping in standard three‑jaw chucks, providing universal compatibility with most Hand Drilling Machines and Drilling Machines used in workshops. Conforming to DIN 1897 and built to the Standard Line specification, the tool offers predictable mounting behaviour and good concentricity. The short length also helps when working near edges or in confined jigs, reducing the leverage that can lead to chatter or misalignment. Suited materials and professional application guidance This Type N drill from MetavCUT is aimed primarily at metalworking professionals and maintenance technicians who need a robust, compact tool for steels, cast materials, non‑ferrous metals and some engineering plastics. The 118° point angle supports easier centring on slightly curved surfaces and softer metals, while the Type N spiral remains the classic choice for metal drilling rather than very soft materials. For workshop jobs that demand reduced breakage and reliable centring, this extra short configuration delivers clear advantages. Highly recommended for precision metalworking: choose the MetavCUT Standard Line Twist Drill Type N for stable drilling in confined spaces — for technical advice and tailored support contact METAV Werkzeuge: 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 56027-FDA Diameter: 2.7 mm Point angle: 118° Type: Type N Execution: extra short Colour: bright finished Material: HSS‑G Shaft execution: cylindrical Spiral length: 14 mm Total length: 43 mm Model series: Standard Line Standard: DIN 1897 Application: Drills for metal / Bohrer für Metall For drilling machine: Drilling Machine / Handbohrmaschine Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Is the MetavCUT Twist Drill Type N suitable for cordless hand drills? The MetavCUT Twist Drill Type N can be used with cordless hand drills provided the chuck secures the cylindrical shank properly and the drill speed and feed are adapted to the material; using suitable cutting fluid and moderate feed reduces wear and the risk of slipping in the chuck. How should the MetavCUT Twist Drill be maintained to ensure long life? Regular sharpening and cleaning of the flute on the MetavCUT Twist Drill Type N keeps the HSS‑G cutting edges effective; inspect for chipping and store drills to avoid impact damage — regrind according to the original point geometry to preserve centring behaviour. What are Twist Drills used for? Twist Drills are mainly applied to the machining of high‑strength workpieces and larger hole diameters. The form is easy to regrind and withstands significant loads, making the MetavCUT Twist Drill Type N suitable for alloyed and unalloyed steel, cast steels and similar materials. Which three drill types are there? The three main drill types are metal drills, wood drills and stone/concrete drills. Why are twist drills sharpened? Sharpening reduces the cross‑cut at the tip of the Twist Drill, which significantly lowers friction forces and thereby reduces required feed force; at the same time the tip centres more reliably in the workpiece. Can a Twist Drill be used to drill wood? A metal (Type N) Twist Drill can be used in wood, but guidance and hole finish are inferior to dedicated wood drills; metal drills are easier to resharpen and have less self‑feeding action. For which drilling depths is the Twist Drill most commonly used? Solid drilling with a Twist Drill is common for diameters up to 20 mm and drilling depths up to 100 mm; it is the most frequently used tool for these ranges when producing holes in solid material. Which is better, HSS or HSSE? The common assumption that HSSE steels are categorically superior to HSS is not correct; evaluate working conditions carefully to decide whether the performance gain justifies the higher cost.

Twist Drill — Type N (Diameter 2.8 mm, 118° tip, Extra Short, Bright Finished, HSS-G, DIN 1897) The Twist Drill Type N is an extra-short HSS-G metal drill designed for Hand Drills and Drilling Machines, offering high stability and controlled drilling in thin-walled materials and alloys. Extra-short HSS-G design for higher stability Efficient cutting up to 40% faster drilling 118° tip angle for soft metals and aluminium Cylindrical shank fits standard three-jaw chucks Conforms to DIN 1897 for robust performance Greater stability and less breakage when space is tight The Extra Short geometry of this Twist Drill reduces overall length and flute length, which increases Stability and diminishes the risk of breakage during manual use. Thanks to the ground HSS-G cutting edges, drilling forces are lower and feed effort is reduced, so holes in thin sheets and profiles can be produced with steadier control and fewer rejects. This makes the tool particularly suitable for repair work and confined-space applications. Faster metal cutting with consistent hole quality A ground HSS-G flute profile and optimized geometry enable up to 40% faster cutting compared with conventional HSS designs while requiring significantly less feed force. The 118° tip angle and Type N spiral are tuned for softer metals such as aluminium and many steel grades, improving centring and reducing chatter on curved surfaces. The result is cleaner holes and more predictable process behaviour for metalworking tasks. Universal mounting, practical handling and limits The Cylindrical Shank (round shank) ensures universal compatibility with standard three-jaw chucks, allowing rapid tool changes without special adaptors. With an overall length of 43 mm and a flute length of 14 mm, the short-length design is ideal for hand and angle drills where access and rigidity matter. Note that round shanks can slip in very high-torque applications, so use an appropriate chuck or torque setting when aggressive drilling is required. Targeted for metalworkers, maintenance and precise DIY Craftsmen, maintenance technicians and precise DIY users benefit from the combination of DIN 1897 conformity, HSS-G material and the compact design. The Twist Drill delivers reliable performance for drilling in alloyed and unalloyed steels, cast materials, non-ferrous metals and hard plastics. Its characteristics make it a practical choice when robustness, re-sharpenability and controlled entry are priorities rather than high-volume production. Strong recommendation for reliable metal drilling — contact METAV Werkzeuge for expert advice and support: METAV CUT Twist Drill Type N suits precise metalworking tasks and constrained workspaces; for technical questions or application guidance reach out via eMail info@metav-werkzeuge.com, telephone +49 2822 7131930 or WhatsApp +49 170 2837271 Twist Drill (Spiralbohrer) Brand: MetavCUT SKU: 56028-FDA Diameter: 2.8 mm Tip angle: 118° Type: Type N Finish: Bright finished Colour: Blank Execution: Extra Short Material: HSS-G Standard: DIN 1897 Shank: Cylindrical Overall length: 43 mm Spiral length: 14 mm Intended for: Drilling Machine / Hand Drill Application: Drills for metal Model series: Standard Line Packaging unit: 10 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What are Twist Drills used for and which materials suit the MetavCUT Twist Drill Type N? The MetavCUT Twist Drill Type N is primarily used for drilling metals; it is suitable for alloyed and unalloyed steel, cast steel, cast iron, sintered iron, malleable cast iron, non-ferrous metals and hard plastics, providing reliable hole quality in these materials. Can the MetavCUT Twist Drill Type N be used with a handheld drill and what advantages does its extra-short design bring? Yes, the Twist Drill Type N from MetavCUT is designed for Hand Drills and Drilling Machines; the extra-short format increases rigidity and reduces the chance of breakage, making it particularly advantageous in confined spaces and when drilling thin-walled components. For what are Twist Drills used? Twist Drills are mainly applied when machining high-strength materials and larger drill diameters. Their form is easy to re-sharpen and they withstand greater loads, which is why the MetavCUT Twist Drill Type N is often selected for demanding metalworking tasks. Which 3 drill types exist? There are three common drill families: metal drills, wood drills and stone/concrete drills. Each type has a geometry adapted to the specific material to ensure optimal centring, chip removal and hole quality.

Kompakte Stabilität und hohe Schnittgeschwindigkeit machen den extra kurzen HSS‑G Spiralbohrer zu einer effizienten Wahl für präzise Metallbohrungen. Die Kombination aus verkürzter Gesamtlänge für erhöhte Verdrehungsfestigkeit und dem Zylinderschaft für universelle Einspannung sorgt für sichere Ergebnisse in dünnen Werkstücken. Bestellen Sie den Spiralbohrer direkt über Metav oder fragen Sie unsere Beratung bei Bedarf an. Spiralbohrer von MetavCUT — extra kurz, HSS‑G, Typ N Der Spiralbohrer ist ein extra kurzer HSS‑G Bohrer für Metall, konzipiert für Handbohrmaschinen und enge Arbeitsräume. Extra kurz für erhöhte Stabilität HSS‑G geschliffen: bis zu 40 % schneller bohren Zylinderschaft: universelle Einspanneignung Spitzenwinkel 118° für weiche bis mittlere Metalle DIN 1897 Norm, Typ N für klassische Metallanwendungen Mehr Stabilität und weniger Bruch bei beengten Platzverhältnissen Die extra kurze Ausführung reduziert die Hebelwirkung und erhöht die Verdrehungsfestigkeit, was insbesondere bei Handgeführten Bohrungen in dünne Bleche und Profile entscheidend ist. Durch die verkürzte Arbeitslänge verringert sich die Bruchneigung des Werkzeugs, sodass sich die Standzeit bei Routinearbeiten deutlich verbessert. Dieser Aufbau macht den Bohrer zur passenden Wahl, wenn wenig Platz für lange Werkzeuge vorhanden ist. Schnelleres Bohren und geringerer Kraftaufwand dank HSS‑G Der geschliffene HSS‑G Werkstoff ermöglicht ein bis zu 40 % schnelleres Bohren und reduziert die benötigte Anpresskraft um etwa 50 % im Vergleich zu herkömmlichen HSS‑Bohrern. Das Ergebnis ist ein zügigeres Arbeiten mit weniger Ermüdung des Anwenders und geringerer Wärmeeinwirkung auf das Werkstück. Diese Vorteile zeigen sich besonders beim Bohren in legierten und unlegierten Stählen sowie in Gusswerkstoffen. Geeignet für Standardanwendungen: Einordnung des Durchmessers Mit einem Durchmesser von 2,9 mm fällt der Bohrer in den Standard‑Bereich (2,0–13,0 mm) und ist daher ideal für Werkstatt, Montage und DIY‑Projekte. Die Empfehlung lautet: Bei hoher Präzision vorher zentrieren; für dünne Werkstoffe ist direktes Bohren möglich. Die Typ‑N Normalspirale sorgt für zuverlässige Spanabfuhr bei Metall und Stahl, nicht jedoch für sehr weiche Werkstoffe. Praxistipps zu Schaft, Spitze und Anwendung Der Zylinderschaft erlaubt die problemlose Einspannung in gängige Dreibackenfutter, was die Handhabung vereinfacht. Beachten Sie jedoch, dass bei sehr hohem Drehmoment ein Durchrutschen möglich ist—ggf. mit passender Aufnahme sichern. Der Spitzenwinkel von 118° ist für weichere bis mittlere Metalle optimiert und erleichtert das Zentrieren auf leicht gewölbten Oberflächen. Verwenden Sie bei Bedarf Kühlschmierstoff, um die Standzeit weiter zu erhöhen. MetavCUT empfiehlt diesen extra kurzen HSS‑G Spiralbohrer für präzise Metallarbeiten mit beschränktem Platz — für Beratung und Lieferung direkt bei Metav: info@metav-werkzeuge.com oder Telefon +49 2822 7131930 Produktmerkmale Artikelnummer: 56029-FDA Marke: MetavCUT Bezeichnung: Spiralbohrer Serie: Standard Line Fakten Durchmesser: 2,9 mm Gesamtlänge: 43 mm Spirallänge: 14 mm Spitzenwinkel: 118° Verpackungseinheit: 10 Besonderheiten Material: HSS-G Ausführung: extra kurz Schaftausführung: Zylinder Farbe: blank Für_Bohrmaschine: Handbohrmaschine Norm: DIN 1897 Typ: Typ N FAQ Für welche Werkstoffe eignet sich der Bohrer besonders gut? Der MetavCUT Spiralbohrer (Typ N, HSS‑G, SKU 56029-FDA) ist besonders geeignet für legierte und unlegierte Stähle, Gussstahl, Gusseisen, Sintereisen, Temperguss sowie Nichteisenmetalle und Hartkunststoffe. Kann der Bohrer in einer Handbohrmaschine verwendet werden? Ja, die Ausführung als extra kurzer Spiralbohrer mit Zylinderschaft wurde speziell für die Nutzung in Handbohrmaschinen ausgelegt; bei hohen Drehmomenten ist jedoch auf sichere Einspannung zu achten. Warum ist die kurze Bauform vorteilhaft? Die extra kurze Bauform erhöht die Stabilität und reduziert Bruchneigung, was besonders beim Bohren in dünne Materialien oder in beengten Situationen zu zuverlässigen Ergebnissen führt. Wie wirkt sich der Spitzenwinkel von 118° aus? Ein Spitzenwinkel von 118° erleichtert das Eindringen in weichere und mittlere Metalle und verbessert das Zentrieren auf leicht gewölbten Oberflächen. Wie viele Stück sind in einer Verpackungseinheit? Die Verpackungseinheit des Spiralbohrers beträgt 10 Stück.

Twist Drill — Type N, 2 mm, 118° Tip, Extra Short, Bright Finished, HSS‑G, DIN 1897 (MetavCUT) The Twist Drill Type N is a compact HSS‑G metal drill bit engineered for precise hand drilling in confined spaces and thin materials. Extra‑short design for improved stability and less breakage Ground HSS‑G for up to 40% faster drilling 118° tip for better centring on curved surfaces Cylindrical shank fits standard three‑jaw chucks Greater Stability and Faster Drilling for Metalworking The Extra Short geometry reduces overhang and increases rigidity, so the bit resists bending and breakage during demanding operations. The ground HSS‑G cutting edges allow up to 40% faster drilling while requiring about 50% less feed force compared with conventional HSS bits, which delivers measurable efficiency gains for production and repair work. Conforming to DIN 1897, this format is optimised for Hand Drills and Angle Drills where space is limited or access is restricted. Clean Holes in a Wide Range of Materials With Type N spiral geometry and a 118° Tip, this bit is designed primarily for metal applications including alloyed and unalloyed steel, cast steel, cast iron, sintered iron, tempered cast, non‑ferrous metals and hard plastics. The tip angle improves centring on slightly curved surfaces and eases entry into softer metals such as aluminium. For users less familiar with drilling technology: the tip angle determines how sharply the bit cuts into the Workpiece—a larger angle reduces tipping and provides steadier guidance. Universal Shank, Practical Limitations, and Best Practices The Cylindrical Shank (round shank) ensures universal compatibility with standard three‑jaw chucks and quick change between typical Hand Drills. For applications with high torque, clamping should be checked as round shanks can slip under extreme loads compared with hex or triangular shanks. The extra‑short overall length (Total length 38 mm, Spiral length 12 mm) is particularly advantageous when drilling thin sheet metal, profiles or components in confined assemblies where a standard‑length bit would be impractical. Who benefits and why this bit stands out Maintenance technicians, metal fabricators and skilled hobbyists will value the combination of compact design and robust HSS‑G performance. As part of the Standard Line from MetavCUT, the bit offers a reliable compromise between cutting speed and durability, delivering reproducible hole quality in everyday workshop scenarios. The relatively small 2 mm diameter and extra short execution make it a specialist choice when precision and low vibration are required. For precision metal drilling choose MetavCUT’s Twist Drill Type N — METAV Werkzeuge offers comprehensive technical advice and application support via eMail: info@metav-werkzeuge.com, Phone: +49 2822 7131930, WhatsApp: +49 170 2837271 Designation: Twist Drill (Spiralbohrer) Marke: MetavCUT SKU: 56020-FDA Diameter: 2 mm Tip Angle: 118° Type: Type N Execution: Extra short Finish / Colour: Bright finished Material: HSS-G Spiral Length: 12 mm Total Length: 38 mm Shank Execution: Cylindrical Suitable For: Drilling Machine (Hand Drill) Application: Drills for metal Model Series: Standard Line Norm: DIN 1897 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ For what is a Twist Drill used? The Twist Drill from MetavCUT (Type N) is mainly applied to machining high‑strength materials and larger bore diameters; its form is easy to resharpen and stands up to greater loads, making it suitable for demanding metalworking where robust performance is required. Which three drill types exist? In general classification there are Metal Drills, Wood Drills and Stone/Concrete Drills; the MetavCUT Twist Drill belongs to the Metal Drill group and is optimised for ferrous and non‑ferrous metals. Why are Twist Drills pointed (regrinded)? MetavCUT Twist Drill bits are pointed to reduce the cross‑cut at the tip; this lowers friction significantly, reducing required feed forces and improving centring of the tip in the Workpiece. Can a Twist Drill be used to drill wood? A metal Twist Drill (Type N) can be used in wood, but the MetavCUT metal drill offers poorer guidance and a less clean finish compared with dedicated Wood Drills; however it is easier to resharpen and has lower self‑feeding tendencies. At which drilling depths is the Twist Drill most used? A full‑bore hole is typically executed with a Twist Drill; for diameters up to 20 mm and drilling depths up to 100 mm the Twist Drill is the most commonly used tool. What is better, HSS or HSSE? The common belief that HSSE steels are always superior to standard HSS is incorrect; when choosing between HSS and HSSE for a MetavCUT Twist Drill, assess whether the working conditions justify the higher purchase cost of HSSE.

Twist Drill 3.1 mm — Type N, Extra Short, Bright Finished, 135° Tip, HSS‑G, DIN 1897 (MetavCUT) The Twist Drill MetavCUT Type N extra short is a robust metalworking drill designed for use with Drilling Machines and hand-held drills, offering high stability and precise performance for demanding metal applications. Extra-short design for increased stability 135° tip for harder materials like stainless steel Ground HSS‑G for faster drilling and less pressure Cylindrical shank for universal chuck compatibility Faster, more efficient metal drilling for professional results The HSS‑G ground geometry of this Twist Drill reduces cutting forces and enables up to 40% faster drilling while requiring significantly less feed pressure, which is especially beneficial when working with alloyed and unalloyed steels. The 135° tip angle is optimised for harder materials such as Stainless Steel and Cast Iron, shortening lead-in time and improving centring. For workshops that prioritise productivity, this drill converts technical features into measurable time savings. Stable, compact design for tight spaces and thin materials An Extra Short length improves rigidity and reduces the risk of breakage when compared with standard-length drills, making it ideal for drilling in thin-walled components, sheet metal and profiles. The Cylindrical Shank fits conventional three-jaw chucks, offering universal compatibility and quick tool changes. These design choices translate into greater confidence when operating in confined or awkward positions where control and stability matter most. Suited applications and intended users This Twist Drill Type N is intended for metalworkers, fabricators, maintenance engineers and ambitious hobbyists who need a reliable solution for drilling in steel, castings, non‑ferrous metals and hard plastics. MetavCUT engineered the drill to perform consistently in workshop and on-site conditions, providing a solid tool choice when precise, repeatable holes in demanding materials are required. Compliance, handling and practical guidance for use Manufactured to DIN 1897, the drill meets recognised standards for dimensions and performance, ensuring predictable results and interchangeability. The Extra Short format makes sharpening and re-grinding straightforward, while the Type N normal spiral geometry remains the classic choice for metal drilling. For best performance use appropriate cutting speeds and cooling when drilling stainless or hardened steels to prolong tool life and maintain hole quality. We strongly recommend the MetavCUT Twist Drill for demanding metalworking tasks — for personalised technical advice and application support contact METAV Werkzeuge by eMail at info@metav-werkzeuge.com or by phone at +49 2822 7131930 (WhatsApp +49 170 2837271) Designation: Twist Drill Brand: MetavCUT SKU: 56031-FDA Diameter: 3.1 mm Total Length: 46 mm Spiral Length: 16 mm Tip Angle: 135° Type: Type N Execution: Extra Short Colour: Bright Finished Shank Design: Cylindrical Material: HSS‑G Standard: DIN 1897 Application: Drills for Metal Model Series: Standard Line Suitable For: Drilling Machine (hand-held drills) Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill used for? The MetavCUT Twist Drill Type N is mainly used for machining high‑strength materials and larger hole diameters; it is particularly suitable for alloyed and unalloyed Steel, Cast Steel, Cast Iron, Sintered Iron, Tempered Castings, non‑ferrous metals and hard plastics. Its Extra Short design also makes it well suited to drilling thin materials and applications with limited space. Which three drill types exist? In general use three main drill types are distinguished: Metal drills, Wood drills and Stone/Concrete drills. The MetavCUT Twist Drill belongs to the classic Metal drill group and is optimised for metalworking tasks. Why are Twist Drills pointed? The point grinding reduces the cross‑cut at the drill tip; by re‑pointing the Twist Drill the friction forces are significantly lowered so that reduced feed forces are needed and the tip centres better in the workpiece, improving accuracy and lowering the risk of walking. Can the Twist Drill be used for wood? A Metal drill such as the MetavCUT Twist Drill can be used in Wood, but guidance and hole quality are inferior compared with dedicated Wood drills. Metal drills are easier to re‑sharpen and show less “self‑feeding”, yet they provide less precise guidance and a rougher finish when used in timber.

Twist Drill — Metal Drill, 3.2 mm, 135°, Type N, Bright Finished, Extra‑Short, HSS‑G, DIN 1897 (by MetavCUT) The Twist Drill is an extra‑short HSS‑G metal drilling tool designed for precise, stable drilling with hand and drilling machines in tight or thin‑walled workpieces. Extra-short HSS-G for improved stability 3.2 mm Diameter for precise metal drilling 135° Tip Angle for harder materials Cylindrical Shank fits standard chucks DIN 1897 Standard, Type N metal twist drill Precision and stability for demanding metalwork This extra‑short HSS‑G drill offers concentrated rigidity that reduces vibration and lowers the risk of breakage during manual or low‑power drilling. The shortened overall length improves torsional resistance, making it possible to apply higher feed without chatter. For work in legated and unlegated Steels, Cast Steel and Non‑Ferrous Metals, the combination of ground flutes and a carefully shaped tip shortens drilling time and reduces required feed force, yielding cleaner holes and longer tool life. Compact design for tight spaces and thin materials With an overall length of 46 mm and a flute length of 16 mm, the short geometry is ideal where access is limited or where only thin plates and profiles are being drilled. The Cylindrical Shank ensures universal compatibility with standard three‑jaw chucks, while the bright finish improves chip evacuation. This configuration suits hand Drilling Machines and angle heads where a standard‑length tool would be impractical, allowing secure clamping and reliable centring in confined assemblies. Tip geometry and spiral type optimised for harder materials The 135° tip angle is engineered to reduce walking and to penetrate harder materials such as stainless steel with less initial force. As a Type N (normal spiral) tool, this drill provides a balanced helix suitable for many metal types, offering robust cutting action without the aggressive self‑pull of specialised wood drills. The tip geometry also facilitates re‑sharpening: by reducing the cross‑cut length, the regrind preserves centring capability and lowers friction during penetration. Who benefits and how this tool improves workflow Maintenance technicians, metal fabricators and installers who frequently drill in sheet metal, profiles or machine parts benefit from the tool’s increased stability and lower feed requirements. Conformity to DIN 1897 and the Standard Line series ensures consistent dimensions and interchangeability, supporting predictable setup times and fewer tool changes. The drill’s robust build and compatibility with common chucks make it a practical choice for everyday metalworking tasks where reliability and repeatability matter. Strong recommendation: choose MetavCUT’s extra‑short Twist Drill for precise, low‑force metal drilling — for expert advice and tailored technical support contact METAV Werkzeuge by eMail at info@metav-werkzeuge.com, by phone at +49 2822 7131930 or via WhatsApp at +49 170 2837271 Bezeichnung: Twist Drill Brand: MetavCUT SKU: 56032-FDA Diameter: 3.2 mm Tip Angle: 135° Type: Type N Execution: Extra short Finish: Bright finished Material: HSS-G Norm: DIN 1897 Flute Length: 16 mm Overall Length: 46 mm Shank: Cylindrical For Drill Machine: Drilling Machine Application: Drills for metal Model Series: Standard Line Packaging Unit: 10 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill by MetavCUT used for? The MetavCUT Twist Drill (Type N) is primarily used for machining high‑strength and ordinary metals and for larger drill diameters; its extra‑short design improves stability, makes regrinding easier and stands up to higher loads during work in Steel, Cast Iron and other hard materials. Which three drill types are there? There are three main drill categories: Metal drill, Wood drill and Stone/Concrete drill. The MetavCUT Twist Drill belongs to the metal drill group and is optimised for drilling in metal rather than in soft timber or masonry.

Der Spiralbohrer überzeugt durch die Kombination aus HSS-G Geschliffenheit, extra kurzer Ausführung und universeller Zylinderschaft, was für mehr Stabilität, geringere Bruchneigung und effizientes Bohren in Metall sorgt; bestellen Sie den Spiralbohrer direkt über Metav Werkzeuge oder fragen Sie unsere Beratung an. Spiralbohrer von MetavCUT — extra kurze HSS-G Ausführung Der Spiralbohrer ist ein extra kurzer, geschliffener HSS-G Bohrer für präzise Metallbohrungen mit hoher Standzeit. Spiralbohrer »56033-FDA« von MetavCUT Extra kurze Ausführung für enge Platzverhältnisse HSS-G geschliffen: Bis zu 40 % schneller Bohren Spitzenwinkel 135° für härtere Werkstoffe Zylinderschaft: Für normale Bohrfutter universell passend Mehr Stabilität und weniger Bruch bei begrenztem Platz Die extra kurze Ausführung reduziert Hebelwirkung und erhöht die Verdrehungsfestigkeit, wodurch die Gefahr von Bruch und Auslauf verringert wird. Gerade in engen Arbeitsbereichen oder bei Winkelbohrungen ermöglicht die kürzere Gesamtlänge eine sauberere Führung. Durch die geschliffene HSS-G Qualität wird die Vorschubkraft reduziert und die Bohrgeschwindigkeit deutlich gesteigert, was Zeitersparnis und weniger Belastung für die Maschine bedeutet. Effizientes Bohren in Stahl, Guss und Nichteisenmetallen Mit einem Spitzenwinkel von 135° und der Typ-N Normalspirale ist der Bohrer speziell für härtere Werkstoffe ausgelegt. Er eignet sich für legierten und unlegierten Stahl, Gussstahl, Gusseisen, Sintereisen, Temperguss sowie für Nichteisenmetalle und Hartkunststoff. Die geschliffene Schneide sorgt für sauberen Spanabtransport und konstante Lochqualität, wodurch Nacharbeit und Gratbildung minimiert werden. Universelle Anwendung und einfache Handhabung Die Zylinderschaft macht den Bohrer kompatibel mit gängigen Handbohrmaschinen und Dreibackenfuttern, sodass er sich problemlos in Werkstatt und Montage einbinden lässt. Wegen der universellen Schaftform empfiehlt sich bei sehr hohem Drehmoment zusätzlich das sichere Spannen im Bohrfutter beziehungsweise der Einsatz eines Spannfutters, um Durchrutschen zu vermeiden. Die extra kurze Bauform ist ideal für dünnwandige Bleche und Profile. Zielgruppe, Einsatzszenarien und Wirtschaftlichkeit Dieser Bohrer wurde für Handwerk, Instandhaltung und industrielle Kleinserien konzipiert, die präzise Metallbohrungen unter Platzbeschränkung benötigen. Die Kombination aus HSS-G Material und extra kurzer Geometrie reduziert Ausfallzeiten und erhöht die Wirtschaftlichkeit, weil weniger Bruch und damit weniger Nachschub erforderlich sind. Sichern Sie sich den präzisen HSS-G Spiralbohrer von MetavCUT über unseren Shop oder kontaktieren Sie die Metav Beratung per E‑Mail an info@metav-werkzeuge.com bzw. telefonisch unter +49 2822 7131930. Produktmerkmale Artikelnummer: 56033-FDA Marke: MetavCUT Serie: Standard Line Bezeichnung: Spiralbohrer Norm: DIN 1897 Fakten Durchmesser: 3,3 mm Gesamtlänge: 46 mm Spirallänge: 16 mm Spitzenwinkel: 135° Verpackungseinheit: 10 Besonderheiten Material: HSS-G (Hochleistungs-Schnellarbeitsstahl, geschliffen) Ausführung: extra kurz (mehr Stabilität, weniger Bruchneigung) Schaftausführung: Zylinder (Rundschaft, universell passend) Typ: Typ N (Normalspirale für Metall) Farbe: blank Für Bohrmaschine: Handbohrmaschine FAQ Für welche Werkstoffe eignet sich der Bohrer am besten? Der MetavCUT Spiralbohrer in HSS-G Ausführung eignet sich besonders für legierten und unlegierten Stahl, Gussstahl, Gusseisen sowie Nichteisenmetalle; die geschliffene Spitze liefert sauberen Spanabtransport und stabile Bohrbilder. Ist der Bohrer für Handbohrmaschinen geeignet? Ja, die Zylinderschaft macht den Spiralbohrer kompatibel mit normalen Dreibackenfuttern an Handbohrmaschine und Winkelbohrmaschinen; bei sehr hohem Drehmoment ist sicheres Spannen zu empfehlen. Welche Vorteile bringt die extra kurze Ausführung in der Praxis? Die extra kurze Bauform des Spiralbohrers reduziert Hebelwirkung, erhöht die Stabilität und verringert die Bruchneigung, was besonders in engen oder schwer zugänglichen Bereichen Zeit und Material spart. Welchen Spitzenwinkel hat der Bohrer und warum ist das wichtig? Der Spiralbohrer hat einen Spitzenwinkel von 135°, was das Anbohren in härtere Werkstoffe erleichtert und die Anbohrzeit reduziert; das Ergebnis sind präzisere und gratärmere Bohrungen. Wie viele Bohrer sind in einer Verpackungseinheit und wie lautet die SKU? Die Verpackungseinheit beträgt 10 Stück und die Artikelnummer beziehungsweise SKU lautet 56033-FDA.

Twist Drill Type N — 3.4 mm, 135° Point Angle, Extra Short, Bright Finished, HSS‑G (DIN 1897) by MetavCUT The Twist Drill Type N is an extra‑short HSS‑G drill bit designed for Hand Drilling Machines, optimised for precise metalworking in tight spaces. Extra‑short design for greater stability 135° point angle for Harder Materials HSS‑G: up to 40% faster drilling Cylindrical shank fits standard chucks DIN 1897 compliant for consistent fit Faster metal drilling with lower feed force The Twist Drill delivers high efficiency when working with alloyed and unalloyed Steel, Cast Steel, Cast Iron, Sintered Iron, Tempered Iron, Non‑Ferrous Metals and Hard Plastics. Thanks to its HSS‑G material and the ground geometry, drilling can be performed up to 40% faster while requiring significantly less axial force. This means shorter cycle times and reduced operator fatigue when performing repetitive holes in demanding materials. Extra‑short geometry increases stability and reduces breakage The extra‑short execution offers a shorter overall length and reduced flute length compared with standard DIN 1897 bits, which improves torsional resistance and lowers the risk of breakage. This design is particularly advantageous for drilling in thin‑walled components or when working in confined setups where a long tool would be impractical. The compact geometry supports controlled chip evacuation and steadier hole starts. 135° point angle and Type N spiral explained A 135° point angle is suited for harder workpiece materials because it reduces the tendency to wander and shortens the initial bite time. The Type N designation denotes the classic normal spiral for metalworking; it is designed for efficient chip removal in metal and stable machining of tougher alloys. For users less familiar with these terms: the point angle determines entry behaviour, and a larger angle generally improves centring and reduces required thrust for hard materials. Universal shank and compatibility with hand drills The cylindrical shank ensures compatibility with standard three‑jaw chucks, offering universal clamping for workshop and maintenance applications. As a result, the bit is well suited to Hand Drilling Machines and Angle Drills. Note that a smooth round shank can be more prone to slipping under very high torque compared with keyed or hex shanks; use appropriate chuck clamping to prevent slippage. Who benefits from this short HSS metal drill This short Twist Drill is aimed at technicians, mechanics and maintenance personnel who need reliable, fast holes in metal under space constraints. It is a practical choice for fabricators working with sheet metal, profile sections and machine repair tasks where a robust, short tool reduces vibration and breakage risk. For hobbyists, it offers easier handling when access to the workpiece is restricted. MetavCUT recommends this Type N Twist Drill for precision metalworking in confined setups — for expert guidance and to confirm suitability contact METAV Werkzeuge: 📧 info@metav-werkzeuge.com; ☎️ +49 2822 7131930; ✔️ WhatsApp +49 170 2837271 Designation: Twist Drill Marke: MetavCUT SKU: 56034-FDA Diameter: 3.4 mm Point Angle: 135° Execution: Extra short Colour / Finish: Bright finished Material: HSS‑G Type: Type N Shaft Design: Cylindrical shank Overall Length: 46 mm Spiral Length / Flute Length: 16 mm Applicable Machine: Hand Drilling Machine (Drilling Machine) Application: Drills for metal Standard: DIN 1897 Model Series: Standard Line Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials is the MetavCUT Twist Drill Type N best suited for? The MetavCUT Twist Drill Type N is primarily intended for metalworking and performs well in alloyed and unalloyed Steel, Cast Steel, Cast Iron, Sintered Iron, Tempered Iron, Non‑Ferrous Metals and Hard Plastics; its HSS‑G composition and Type N spiral optimise chip removal and tool life in these materials. Can the Twist Drill be used in an angle drill or only in straight hand drills? The Twist Drill with a cylindrical shank is designed to be clamped in standard three‑jaw chucks, so it is compatible with both straight Hand Drilling Machines and many Angle Drills; ensure secure clamping to avoid slippage under higher torque. For what is a Twist Drill used? It is mainly applied to the machining of high‑strength workpieces and larger drill diameters. The Twist Drill geometry is easy to regrind and withstands higher loads. Which three drill types exist? There are Metal drills, Wood drills and Stone/Concrete drills. Why are Twist Drills sharpened (pointed)? Sharpening reduces the cross‑cut at the tip of the Twist Drill, which significantly lowers friction and therefore requires lower feed forces while improving centring in the workpiece. Can you drill wood with a Twist Drill? A Metal drill can be used in wood, but guidance is poorer and the hole finish is less clean; however, such bits are easier to resharpen and show lower self‑feeding tendency. For which drill depths is the Twist Drill most used? A through hole in solid material is typically performed with a Twist Drill. For diameters up to 20 mm and drill depths up to 100 mm, the Twist Drill is the most frequently used tool. Is HSS or HSSE better? The common belief that HSSE steels are categorically superior to standard HSS is incorrect; consider your working conditions carefully to decide whether the higher cost of HSSE is justified.

Twist Drill Type N — extra short, Ø 3.5 mm, 135°, bright finished, HSS‑G, DIN 1897 The Twist Drill Type N is an extra short HSS‑G drill bit designed for precision metalworking with hand Drilling Machines in confined spaces. Extra short HSS‑G design for high stability 135° point angle for hard materials Cylindrical shank for universal chuck fit Ideal for hand and angle Drills in tight spaces Conforms to DIN 1897 for consistent quality Faster, more controlled drilling for demanding metalwork The extra short geometry reduces flex and breakage risk when working with metal, delivering a more stable cutting action compared with standard lengths. The ground HSS‑G cutting edges enable up to a 40% faster drilling speed and require about 50% less axial force, which translates into reduced operator fatigue and more reliable hole quality. This makes the bit particularly suitable where precision and repeatability are required. Robust tip and geometry for hard materials A 135° point angle combined with the Type N normal spiral provides better centring and reduced walking in harder steels and stainless alloys. The blunter tip shortens the initial penetration time and distributes cutting loads, so drilling into tougher materials like tempered or alloyed steels becomes more efficient. This geometry helps to extend tool life while maintaining consistent hole geometry. Universal fit and practical handling in confined spaces The drill features a cylindrical shank that fits standard three‑jaw chucks, offering broad compatibility with typical hand and angle Drilling Machines. With a total length of 52 mm and a spiral length of 20 mm, the compact form factor is ideal for shallow holes, sheet metal, profiles and situations where access is limited. The bright finished surface aids chip evacuation and makes bit handling straightforward on the bench. Application focus and recommended uses Manufactured to DIN 1897 from HSS‑G, this Twist Drill is designed for drilling Alloyed and Unalloyed Steel, Cast Steel, Cast Iron, Sintered Iron and Non‑Ferrous Metals, as well as Hard Plastics. The extra short design is particularly advantageous when working with thin‑walled components or when the setup cannot accommodate longer tools. Users seeking a robust, easy‑to‑control solution for metal drilling will find reliable performance with this geometry and material combination. We recommend the MetavCUT Type N extra short Twist Drill for precision metalworking; for product advice or technical data contact METAV Werkzeuge — Email: info@metav-werkzeuge.com — Phone: +49 2822 7131930 — WhatsApp: +49 170 2837271 Technical Information Designation: Twist Drill Brand: MetavCUT SKU: 56035‑FDA Diameter: 3.5 mm Point angle: 135° Type: Type N Material: HSS‑G Execution: extra short Colour: bright finished Shank execution: cylindrical Spiral length: 20 mm Total length: 52 mm Norm: DIN 1897 Model series: Standard Line Application: Drills for metal For drilling machine: Drilling Machine Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill Type N mainly used for? The MetavCUT Twist Drill Type N is primarily used for drilling in high‑strength materials and larger diameters; its extra short design is well suited to metalworking tasks where stability and reduced breakage are important. Can the MetavCUT Twist Drill Type N be used with a hand Drilling Machine? Yes, the MetavCUT Twist Drill Type N with a cylindrical shank is intended for use in common hand Drilling Machines and angle drills, offering universal chuck compatibility for workshop and on‑site applications. What are Twist Drills used for? Twist Drills are mainly applied to the machining of high‑strength materials and larger drill diameters; their form is easy to re‑grind and they withstand considerable loads. Which three drill types are there? The three main drill types are metal drills, wood drills and stone/concrete drills. Why are Twist Drills sharpened? Sharpening reduces the cross‑cut at the tip of the Twist Drill, which lowers friction and therefore reduces the required feed forces while improving centring in the workpiece. Can a metal drill be used to drill wood? A metal drill can be used in wood, but guidance and finish are inferior compared with dedicated wood drills; metal drills are easier to re‑grind and have less self‑feeding action.

Die Kombination aus Extra Kurzer Bauform, HSS-G-Schneide und Zylinderschaft sorgt für stabile, schnelle und vielseitige Metallbohrungen; profitieren Sie von geringerer Bruchneigung und erhöhter Bohrgeschwindigkeit und bestellen Sie den Spiralbohrer direkt über Metav oder kontaktieren Sie unsere Beratung bei Fragen. Spiralbohrer 3,6 mm von MetavCUT (Typ N) Spiralbohrer 3,6 mm für präzise Metallbohrungen in dünnen Blechen und Profilen, extra kurz und robust für Hand- und Winkelbohrmaschinen. Extra kurze Bauform für mehr Stabilität HSS-G: schnelleres Bohren in Stahl und Guss Spitzenwinkel 135° für harte Werkstoffe Zylinderschaft, passend für Dreibackenfutter DIN 1897 Standard, Typ N Standardspirale Mehr Stabilität bei beengten Platzverhältnissen und dünnen Werkstücken Die Extra Kurze Ausführung reduziert die Hebelwirkung und minimiert die Bruchneigung, was insbesondere beim Bohren in dünnen Blechen oder engen Bohrpositionen entscheidend ist. Durch die kürzere Spirallänge verbessert sich die Rundlaufgenauigkeit, sodass weniger Nacharbeit erforderlich wird. Anwender profitieren von einer bis zu 40 % schnelleren Bohrleistung und einem um 50 % reduzierten Anpressdruck gegenüber herkömmlichen HSS-Varianten, was die Bedienung mit Handbohrmaschinen deutlich erleichtert. Materialqualität und Schneidwinkel für harte Metalle Der Einsatz von HSS-G sorgt für hohe Verschleißfestigkeit und thermische Belastbarkeit beim Bohren in legierten und unlegierten Stählen, Guss und Hartkunststoffen. Der Spitzenwinkel 135° reduziert das Ausbrechen beim Anbohren harter Werkstoffe und verkürzt die Anbohrzeit, weil die Schneide flacher auftrifft. Als Typ N mit Normalspirale eignet sich der Bohrer besonders für metallische Werkstoffe, wobei die Schneidengeometrie ein ausgewogenes Vorschubverhalten und zuverlässige Spanabfuhr gewährleistet. Kompatibilität mit Werkstatt- und Handmaschinen für den Alltag Die Zylinderschaft macht den Bohrer universell einsetzbar in gängigen Dreibackenfuttern von Handbohrmaschinen und Winkelschleifern mit Bohrfutter. Für den Durchmesser im Standard-Bereich (2,0 mm–13,0 mm) ist dieses Werkzeug ideal geeignet für Werkstattarbeiten, Montage und DIY‑Projekte; bei höherer Präzision empfiehlt sich vorheriges Anpunkten mit einem Zentrierbohrer. Die extra kurze Ausführung ist speziell dann von Vorteil, wenn wenig Platz für Ausklinkungen oder Innenbearbeitung vorhanden ist. Praktische Anwendungstipps für saubere Bohrresultate Vor dem Bohren sollte die Bohrstelle entgratet und, falls möglich, mit Schneidöl leicht geschmiert werden, um Standzeit und Oberflächenqualität zu verbessern. Für saubere Passungen gilt: Anbohren über ein Zentrierloch erhöht die Präzision; bei tiefen Löchern ist Mehrstufiges Aufbohren ratsam, um die Querschneide zu entlasten. Beachten Sie die maximale effektive Bohrtiefe im Verhältnis zum Durchmesser; bei diesem Durchmesser reichen gewöhnlich direkte Bohrungen aus, solange die Maschine stabil gespannt ist. Nutzen Sie die hohe Stabilität und Schnittgeschwindigkeit des MetavCUT Spiralbohrers (SKU 56036-FDA) für exaktere Metallbohrungen und bestellen Sie direkt bei Metav – bei technischen Fragen: info@metav-werkzeuge.com Produktmerkmale Artikelnummer: 56036-FDA Marke: MetavCUT Bezeichnung: Spiralbohrer Serie: Standard Line Typ: Typ N Norm: DIN 1897 Material: HSS-G Farbe: blank Schaftausführung: Zylinder Gesamtlänge: 52 mm Spirallänge: 20 mm Spitzenwinkel: 135° Ausführung: extra kurz Anwendung: Bohrer für Metall Verpackungseinheit: 10 Daten Durchmesser: 3,6 mm Gesamtlänge: 52 mm Spirallänge: 20 mm Spitzenwinkel: 135° Verpackungseinheit: 10 Besonderheiten HSS-G: Hochleistungs-Schnellstahl, verschleißfest DIN 1897: Standard für Spiralbohrer, Maß- und Formtreue Zylinder: Rundschaft, passend für Dreibackenfutter Typ N: Normalspirale, geeignet für Metall und Stahl Extra kurz: Kürzere Gesamtlänge und Arbeitslänge für höhere Stabilität Anwendung: geeignet für Handbohrmaschine und Winkelbohrmaschinen FAQ Wie geeignet ist der Bohrer für Edelstahl und gehärtete Stähle? Der MetavCUT Spiralbohrer (Typ N, SKU 56036-FDA) mit Spitzenwinkel 135° ist für härtere Werkstoffe deutlich besser geeignet als spitzere Bohrer; bei sehr gehärteten Stählen empfiehlt sich jedoch spezialisierter Bohrerwerkstoff. Kann der Bohrer in einer Handbohrmaschine verwendet werden? Ja, die Zylinderschaft macht den Spiralbohrer kompatibel mit gängigen Dreibackenfuttern von Handbohrmaschinen; bei hohem Drehmoment ist auf sicheren Sitz im Bohrfutter zu achten. Für welche Werkstoffe ist dieser Bohrer am besten geeignet? Der HSS-G Spiralbohrer ist optimiert für legierten und unlegierten Stahl, Gussstahl, Gusseisen, Sintereisen, Temperguss sowie Nichteisenmetalle und Hartkunststoffe. Wie verhindert man Bruch bei der Nutzung des extra kurzen Bohrers? Kurze Bohrerlängen reduzieren die Bruchgefahr; zusätzlich helfen korrekt gewählter Vorschub, moderate Drehzahlen und Einsatz von Schneidöl, die Standzeit zu erhöhen. Worin besteht der Vorteil der extra kurzen Ausführung gegenüber Standardlängen? Die Extra Kurze Bauform erhöht die Verdrehungsfestigkeit, verringert das Risiko des Verkippens und ermöglicht präzise Bohrungen in engen Bauteilen.

Twist Drill — Type N · 3.7 mm · 135° Tip · Extra Short · Bright Finished · HSS‑G · DIN 1897 The Twist Drill is an extra‑short Type N drill for Drilling Machines, designed for stable, precise metalworking in confined spaces. Extra‑short design for superior stability 135° tip for harder materials and faster entry HSS‑G material for high wear resistance Cylindrical shank for universal chuck compatibility DIN 1897 standard ensures industrial reliability Faster, more stable drilling in limited spaces The Extra‑Short design reduces flex and the risk of breakage, producing more stable cutting when working in tight or thin components. Because the overall length and flute length are shortened, the cutting forces focus more directly at the tip; this means improved concentricity and less vibration during use. For metalworking tasks where access is limited, the compact geometry offers a practical advantage while maintaining tool life and reliability. Optimised geometry for harder materials Equipped with a 135° tip, this Type N drill is optimised for drilling harder metals such as stainless steel. A larger tip angle reduces the initial bite and shortens lead‑in time, lowering the required thrust and improving centring. For customers unfamiliar with tip geometry: the tip angle influences how aggressively the drill cuts and how well it self‑centres; 135° is commonly chosen for tougher, less ductile materials. High‑speed steel G grade for durable performance Manufactured from HSS‑G, the Twist Drill combines toughness with thermal resistance suitable for continuous metal drilling. Compared with standard HSS, the ground geometry enables up to 40% faster drilling with around 50% less feed force in many cases. This characteristic is particularly beneficial when working on alloys, cast steels, and non‑ferrous metals where consistent cutting performance and regrindability matter. Practical compatibility and application scope The cylindrical shank makes the tool universally compatible with standard three‑jaw chucks on Hand and Angle Drilling Machines. While the round shank is ideal for general clamping, operators should note that very high torque applications may require alternative shank types to avoid slippage. Intended primarily as a metalworking tool, the drill excels in thin materials such as sheets, profiles and plate where a short, stiff geometry is advantageous. Target users and workshop recommendation Designed for professionals and advanced hobbyists tackling precision metal fabrication, the drill suits those needing a compact, resilient cutting tool for confined assemblies and maintenance tasks. The Standard Line model offers dependable repeatability for production or repair work, and its classic Type N flute form provides familiar handling and easy regrinding for workshops that maintain their own tooling. Strong recommendation: Choose the MetavCUT Extra‑Short Twist Drill for demanding metal drilling tasks — for personalised advice or detailed technical data contact METAV Werkzeuge by eMail at info@metav-werkzeuge.com, by phone +49 2822 7131930 or via WhatsApp +49 170 2837271 Twist Drill Brand: MetavCUT SKU: 56037-FDA Diameter: 3.7 mm Tip Angle: 135° Type: Type N Finish: Bright finished Execution: Extra Short Material: HSS‑G Standard: DIN 1897 Suitable for: Drilling Machine (Hand drilling machines and angle drills) Spiral Length: 20 mm Overall Length: 52 mm Shank: Cylindrical Model Series: Standard Line Application: Drills for metal Colour: Bright finished Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill used for and which materials suit it best? The MetavCUT Twist Drill Type N is primarily used for machining high‑strength materials and larger diameters in metalworking. Its extra‑short form is especially useful for drilling thin sheets and profiles, and the HSS‑G grade and ground geometry make it suitable for alloyed and unalloyed steel, cast steel, cast iron and non‑ferrous metals. Which three drill types exist? The main categories of drill bits are metal drills, wood drills and masonry/concrete drills, each optimised for the respective material properties and cutting requirements.

Twist Drill — Type N, 3.8 mm, 135° tip, Extra Short, Bright Finished, HSS‑G, DIN 1897 The Twist Drill (Type N) is an extra short, bright finished HSS‑G metal drill designed for precise work in tight spaces and for use with hand and drilling machines. Extra Short design for improved stability 135° tip angle for harder materials HSS‑G material for high wear resistance Cylindrical shank for standard three‑jaw chucks Conforms to DIN 1897 for robust performance Faster, more controlled metal drilling with HSS‑G performance The Twist Drill from MetavCUT combines HSS‑G construction with a ground flute geometry to enable up to 40% faster drilling while requiring significantly less feed force. This results in less operator fatigue and more consistent holes when working with alloyed and unalloyed steels, cast steels, non‑ferrous metals and hard plastics. For users looking to boost shop productivity, the reduced cutting forces translate directly into smoother operation and fewer rework cycles. Extra short length increases stability and reduces breakage risk Designed to the DIN 1897 extra short specification, this drill’s reduced overall length improves torsional rigidity and lowers the chance of breakage during demanding operations. In confined setups or where minimal overhang is essential—such as thin sheet metal, profiles and tight fixture arrangements—the Extra Short execution gives a decisive handling advantage and steadier guidance through the workpiece. Compatible shank and practical use in hand drills Equipped with a cylindrical shaft, the bit fits common three‑jaw chucks on hand drills and drilling machines, ensuring universal clamping and straightforward replacement. When used in hand drilling, the Type N normal spiral geometry supports reliable chip evacuation in metalworking tasks; apply moderate, steady feed to benefit from the improved centring and reduced tendency to wander. Who benefits and where this drill excels Workshop technicians, maintenance teams and metal fabricators seeking a reliable standard‑spiral metal drill will appreciate the Standard Line quality of this tool. Its 135° tip angle shortens the initial penetration time for harder materials and assists in maintaining concentricity. For less experienced users, the robust design makes it easier to achieve clean results while still allowing sharpening and resharpening when needed. Strong recommendation: Choose MetavCUT’s Extra Short Twist Drill (Type N) for demanding metal applications — METAV Werkzeuge offers expert guidance if unsure which drill best fits your project; contact info@metav-werkzeuge.com or call +49 2822 7131930 or WhatsApp +49 170 2837271 Designation: Twist Drill Brand / Manufacturer: MetavCUT SKU: 56038-FDA Diameter: 3.8 mm Overall length: 52 mm Spiral length: 20 mm Tip angle: 135° Type: Type N Execution: Extra Short Finish / Colour: Bright finished Shank: Cylindrical Material: HSS‑G Standard: DIN 1897 Application: Drills for metal For use in: Drilling Machine / Hand Drill Model series: Standard Line Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials can the Twist Drill (Type N) from MetavCUT handle? The MetavCUT Twist Drill Type N is designed primarily for metalworking: it drills alloyed and unalloyed steel, cast steel, cast iron, sintered iron, malleable cast iron, non‑ferrous metals and hard plastics, offering reliable performance across typical workshop materials. Is the MetavCUT Twist Drill suitable for hand drills and machines? Yes, the Twist Drill with a cylindrical shank fits standard three‑jaw chucks and is suitable for use in both hand drills and larger drilling machines; its extra short design improves stability especially in manual or angled operations. For what is a Twist Drill used? A Twist Drill is mainly applied to the machining of high‑strength materials and larger drill diameters. This shape is easy to resharpen and withstands higher loads, making it well suited for demanding metalworking tasks. Which three drill types exist? The three primary drill types are metal drills, wood drills and stone/concrete drills.

Der extra kurze Spiralbohrer kombiniert HSS-G-Material und 135° Spitzenwinkel für kraftvolles Bohren in Metall; die kurze Bauform reduziert Bruchneigung und erhöht Stabilität, während die geschliffene Geometrie bis zu 40% schnelleres Bohren bei 50% weniger Anpresskraft ermöglicht – bestellen Sie den Bohrer direkt über Metav oder lassen Sie sich vor dem Kauf fachkundig beraten. Spiralbohrer von MetavCUT — HSS-G, Typ N, DIN 1897 (3,9 mm, extra kurz) Der Spiralbohrer ist ein extra kurzer HSS-G Metallbohrer, entwickelt für präzise Bohrungen in legierten und unlegierten Stählen sowie Gusswerkstoffen mit Handbohrmaschine und Winkelbohrmaschinen. Spiralbohrer »Spiralbohrer« von MetavCUT Extra kurz für mehr Steifigkeit beim Bohren HSS-G geschliffen: bis zu 40% schneller arbeiten Spitzenwinkel 135° für harte Werkstoffe Zylinderschaft: universelle Aufnahme im Bohrfutter Stabile Bauform reduziert Bruchrisiko und sorgt für saubere Bohrungen Die extra kurze Ausführung bietet eine deutlich höhere Verdrehungsfestigkeit als Standardlängen und minimiert so Vibration und Bruchneigung bei Handbedienung. Das ist besonders vorteilhaft beim Bearbeiten von dünnwandigen Blechen und Profilen, weil die verkürzte Gesamtlänge die Führung verbessert und die Entstehung von Ausrissen am Austritt reduziert. Anwender profitieren von gleichmäßigeren Bohrbildern und längerer Werkzeugstandzeit. Geschliffenes HSS-G für schnellere, effizientere Metallbearbeitung Dank der geschliffenen Schneide aus HSS-G ermöglicht dieses Spiralwerkzeug eine deutlich höhere Schnittgeschwindigkeit und geringere Vorschubkräfte; Labor- und Praxiswerte zeigen bis zu 40% schnellere Bohrfortschritte bei rund 50% weniger Anpresskraft gegenüber herkömmlichen HSS-Ausführungen. Der 135° Spitzenwinkel wurde gewählt, um Anbohrverhalten in harten Werkstoffen wie Edelstahl zu verbessern und längere Werkzeugstandzeit zu erreichen. Praxisgerechte Einsatzbereiche und Maschinenkompatibilität Mit einem Durchmesser von 3,9 mm gehört dieses Werkzeug in den Standard-Bereich für Alltagsarbeiten. Es eignet sich für Handbohrmaschine und stationäre Geräte, zum Bohren in Baustahl, Aluminium, Gusseisen und Hartkunststoff. Für präzise Passungen empfiehlt es sich, vor dem Endbohren anzupunkten, um Wanderneigung zu vermeiden. Hobbywerkstatt und professionelle Werkstatt profitieren gleichermaßen von der universellen Einsetzbarkeit. Schaft, Maße und Handling: Praktisch und universell einsetzbar Der Zylinderschaft (Rundschaft) sorgt für unkomplizierte Aufnahme in gängige Dreibackenfutter, ohne Spezialaufnahmen zu benötigen. Mit einer Spirallänge 20 mm und einer Gesamtlänge 52 mm ist das Werkzeug kompakt und besonders dann geeignet, wenn wenig Platz für die Bearbeitung vorhanden ist. Die Verpackungseinheit enthält praktische Mengen für Werkstattbedarf und reduziert Logistikaufwand. Empfehlung: Den MetavCUT Standard Line HSS-G Spiralbohrer für extra kurze Anwendungen direkt bei Metav beziehen — per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930, alternativ WhatsApp +49 170 2837271 für schnelle Rückfragen. Technische Daten Artikelnummer: 56039-FDA Marke: MetavCUT Serie: Standard Line Norm: DIN 1897 Fakten Durchmesser: 3,9 mm Gesamtlänge: 52 mm Spirallänge: 20 mm Spitzenwinkel: 135° Verpackungseinheit: 10 Besonderheiten Material: HSS-G (hohe Verschleißfestigkeit, geschliffen) Ausführung: extra kurz (verbesserte Stabilität, geringere Bruchneigung) Schaftausführung: Zylinder (universelle Aufnahme im Dreibackenfutter) Typ: Typ N (Normalspirale, geeignet für Metall) Farbe: blank (heller, fertig bearbeiteter Schaft) Für Bohrmaschine: Handbohrmaschine (geeignet für handgeführte Anwendungen) FAQ Ist dieser Bohrer für Edelstahl geeignet? Der Spiralbohrer von MetavCUT (Typ N, SKU 56039-FDA) mit 135° Spitzenwinkel eignet sich für viele härtere Werkstoffe einschließlich Edelstahl; bei sehr zähen Edelstählen empfiehlt sich reduzierter Vorschub und Kühlung. Welche Maschinen sind kompatibel mit dem Zylinderschaft? Der Zylinderschaft dieses HSS-G Bohrers passt in alle üblichen Dreibackenfutter, deshalb ist er für die Handbohrmaschine und viele stationäre Bohrmaschinen geeignet. Wie wirkt sich die extra kurze Bauform beim Bohren aus? Die extra kurze Ausführung erhöht die Steifigkeit und verringert Vibrationen, was die Bruchgefahr reduziert und saubere Bohrbilder in dünnwandigen Materialien fördert. Für welche Werkstoffe ist der Typ N Spiralbohrer empfohlen? Der Typ N Normalspirale ist insbesondere für Eisen, Stahl, Gussstahl und Nichteisenmetalle ausgelegt; weiche Materialien wie Holz sind nicht optimal, da die Spiralflanke hier andere Geometrien bevorzugt. Wie tief kann ich mit diesem Durchmesser sicher bohren? Bei einem Durchmesser von 3,9 mm sind normale Bohrtiefen im Bereich der Spirallänge möglich; für sehr tiefe Löcher empfiehlt sich abgestuftes Aufbohren und Spanabfuhrüberwachung.

Kompakter, extra kurzer Spiralbohrer mit HSS‑G-Schneidstoff, 3 mm Durchmesser und 135° Spitzenwinkel bietet erhöhte Stabilität, geringere Bruchneigung und bis zu 40 % schnellere Bohrleistung gegenüber herkömmlichen HSS‑Bohrern; Bestellen Sie das Produkt direkt über Metav oder fragen Sie unsere Beratung bei Bedarf an Spiralbohrer 3 mm extra kurz von MetavCUT Der Spiralbohrer 3 mm in extra kurzer Ausführung eignet sich für präzise Metallbohrungen in engen Räumen und für den Einsatz mit Handbohrmaschine. Extra kurz für höhere Stabilität und weniger Bruchneigung HSS‑G geschliffen: bis zu 40 % schnelleres Bohren Zylinderschaft: universell passend für Dreibackenfutter 135° Spitzenwinkel für harte Werkstoffe Spiralänge 16 mm: ideal für Bleche und Profile Mehr Stabilität durch die extra kurze Bauform Die extra kurz ausgeführte Bauform reduziert Hebelwirkung und Vibrationen und führt so zu deutlich geringerer Bruchanfälligkeit bei kleinen Durchmessern. Dadurch wird das Arbeiten in beengten Bereichen vereinfacht und die Standzeit des Werkzeugs erhöht. Besonders bei dünnwandigen Bauteilen sorgt die kompakte Länge für verbesserte Rundlaufgenauigkeit und verlässliche Bohrlöcher. Schneller und effizienter schneiden mit HSS‑G Der aus HSS‑G gefertigte, geschliffene Bohrer reduziert die Anpresskraft und ermöglicht ein bis zu 40 % schnelleres Bohren gegenüber herkömmlichen HSS‑Ausführungen. Die gesteigerte Schnittfähigkeit führt zu saubereren Bohrbilden und reduziert Nacharbeiten, was Zeit und Kosten in der Werkstatt spart. Für Anwender bedeutet das weniger Ermüdung und höhere Produktivität. Geeignet für typische Metallanwendungen in Werkstatt und Montage Der Bohrer ist für den Standard‑Bereich (2,0 mm–13,0 mm) ausgelegt und damit bestens geeignet für Werkstatt, Montage und DIY‑Projekte. Empfohlenes Einsatzfeld sind dünne bis mittlere Bleche, Profile sowie legierte und unlegierte Stähle, Gusseisen und Nichteisenmetalle. Bei hoher Präzision empfiehlt sich vorheriges Anpunkten mit einem Zentrierbohrer, um ein Wandern zu vermeiden. Eigenschaften der Spitze und Spirale verständlich erklärt Der 135° Spitzenwinkel sorgt für einen flacheren Ansatz, der das Anbohren in harten Werkstoffen wie Edelstahl erleichtert und die Anbohrzeit verkürzt. Die Normalspirale (Typ N) ist die klassische Spirale für Metall und bietet eine ausgewogene Späneförderung bei üblichen Vorschubwerten. Diese Kombination ermöglicht saubere Bohrungen bei geringem Werkzeugverschleiß. Hinweise zur Schaftausführung und Einspannung Die Zylinderschaft erlaubt die universelle Nutzung in Dreibackenfuttern von Handbohrmaschinen. Das erleichtert schnellen Werkzeugwechsel. Bei höheren Drehmomenten besteht allerdings die Möglichkeit des Durchrutschens; hier empfiehlt sich eine sorgfältige Spannprüfung oder der Einsatz von Spannhülsen bzw. besser geeigneten Schaftformen bei stationären Anwendungen. Praxisempfehlungen für sicheres und effizientes Arbeiten Zum sauberen Arbeiten empfiehlt sich angepasstes Kühlmittel bei zähen Werkstoffen und moderater Vorschub, um Überhitzung zu vermeiden. Für den Durchmesserbereich 2–13 mm kann in vielen Fällen direkt gebohrt werden; bei sehr präzisen Passungen ist Anpunkten sinnvoll. Die kurze Bauform unterstützt gutes Führungsverhalten, reduziert Schwingungen und macht das Bohren in engen Einbausituationen zuverlässig möglich. Nutzen Sie die robuste HSS‑G Kurzbauform von MetavCUT und ergänzen Sie Ihre Werkstattausrüstung mit diesem stabilen 3 mm Bohrer; bei Fragen erreichen Sie unsere Beratung per eMail info@metav-werkzeuge.com oder telefonisch unter +49 2822 7131930 Produktmerkmale Artikelnummer: 56030-FDA Marke: MetavCUT Serie: Standard Line Norm: DIN 1897 Fakten Durchmesser: 3 mm Gesamtlänge: 46 mm Spiralänge: 16 mm Spitzenwinkel: 135° Verpackungseinheit: 10 Besonderheiten Material: HSS‑G (Hochleistungsschnellarbeitsstahl) Ausführung: extra kurz Schaftausführung: Zylinder Typ: Typ N (Normalspirale) Für Bohrmaschine: Handbohrmaschine Farbe: blank Hersteller: MetavCUT Serie: Standard Line FAQ Für welche Materialien eignet sich dieser Bohrer besonders gut? Der MetavCUT Spiralbohrer aus der Standard Line mit HSS‑G eignet sich besonders für legierte und unlegierte Stähle, Gusseisen, Temperguss sowie Nichteisenmetalle; die Kombination aus HSS‑G und 135° Spitzenwinkel gewährleistet gute Anbohr‑ und Zerspanungseigenschaften. Ist der Bohrer für den Einsatz in einer Handbohrmaschine geeignet? Ja, die Ausführung mit Zylinderschaft ist für Dreibackenfutter von Handbohrmaschinen vorgesehen; der Spiralbohrer 3 mm (SKU 56030-FDA) wurde für universelle Einsätze in der Werkstatt konzipiert. Wie vermeide ich ein Durchrutschen im Bohrfutter? Bei der Zylinderschaft auf feste Spannung im Dreibackenfutter achten und gegebenenfalls Spannhülsen oder Alternativen mit 3‑Kant‑Schaft verwenden; zudem sorgt korrektes Anziehen des Futters für sicheren Halt. Brauche ich beim Bohren in Edelstahl einen anderen Spitzenwinkel? Der 135° Spitzenwinkel dieses Bohrers ist speziell für härtere Werkstoffe wie Edelstahl ausgelegt und reduziert das Abheben beim Anbohren; für sehr weiche Werkstoffe sind flachere Winkel schneller, dort ist dieser Typ jedoch nicht optimal. Wie unterscheidet sich die extra kurze Ausführung im Alltag? Die extra kurze Bauform bietet mehr Stabilität und geringere Bruchgefahr bei kleinen Durchmessern; für enge Bauverhältnisse und dünnwandige Bauteile ist sie praxistauglicher und ermöglicht kontrollierteres Bohren.

Spiralbohrer – MetavCUT Standard Line, HSS-G, 4,1 mm Der Spiralbohrer in extra kurzer Ausführung ermöglicht stabile und kraftsparende Bohrungen in Metall bei begrenztem Bauraum. Spiralbohrer MetavCUT, Typ N Extra kurze Ausführung für enge Arbeitsräume HSS-G: schnelles Bohren in Stahl und Guss Zylinderschaft: passt in Standard-Bohrfutter 135° Spitzenwinkel für härtere Werkstoffe Mehr Leistung durch geschliffene HSS-G-Schneide für schnellere Ergebnisse Die geschliffene HSS-G-Schneide reduziert die Reibung und ermöglicht nach Herstellerangaben ein um bis zu 40 % schnelleres Bohren sowie rund 50 % geringere Anpresskraft gegenüber herkömmlichen HSS-Varianten. Dies bedeutet weniger Ermüdung bei der Arbeit und höhere Produktivität in der Werkstatt. Mit dieser Kombination aus robuster Werkstoffauswahl und optimierter Geometrie wird die Bearbeitungszeit bei Serien- und Einzelfertigungen spürbar verkürzt. Extra kurze Bauform sorgt für Stabilität und Flexibilität beim Bohren in engen Bereichen Die extra kurze Bauform erhöht die Verdrehungsfestigkeit und senkt die Bruchneigung, wenn wenig Bauraum zur Verfügung steht. Dadurch eignet sich der Bohrer besonders für Bleche, Profileisen und andere dünnwandige Werkstücke. Anwender profitieren von einfacher Handhabung in Winkelbohrmaschinen und bei beengten Montageverhältnissen, ohne auf Standzeit oder Präzision verzichten zu müssen. Universelle Schaftausführung und passende Geometrie für Metallanwendungen Der Zylinderschaft gewährleistet eine problemlose Aufnahme in gängige Dreibackenfutter und macht den Bohrer universell einsetzbar in Handbohrmaschine und Winkelbohrmaschine. Die 135° Spitzenwinkel-Geometrie optimiert das Anbohren härterer Werkstoffe wie legierten Stahl und Guss und reduziert das Auslaufen beim Startpunkt. So entstehen sauberere Bohrbilder und geringerer Nacharbeitaufwand. Zielgruppe, Einsatzbereiche und Praxistipps für sichere Ergebnisse Entwickelt für Werkstatt, industrielle Instandhaltung und anspruchsvolle Heimwerker, liefert die Standard Line zuverlässige Ergebnisse beim Bohren in legierten und unlegierten Stahl, Gussstahl, Gusseisen sowie Nichteisenmetallen. Zur Vermeidung von Durchrutschen im Bohrfutter empfiehlt sich bei hohem Drehmoment die Nutzung eines Spannfutters mit zusätzlicher Sicherung. Für höhere Präzision vorzentrieren oder ein kleines Ansenkbohrloch setzen. Setzen Sie auf den MetavCUT Standard Line Spiralbohrer in extra kurzer Ausführung für effizientere Metallbearbeitung; bei technischen Fragen steht Metav direkt zur Verfügung unter info@metav-werkzeuge.com oder telefonisch unter +49 2822 7131930. Produktmerkmale Artikelnummer: 56041-FDA Marke: MetavCUT Serie: Standard Line Bezeichnung: Spiralbohrer Norm: DIN 1897 Daten Durchmesser: 4,1 mm Gesamtlänge: 55 mm Spirallänge: 22 mm Spitzenwinkel: 135° Verpackungseinheit: 10 Besonderheiten Material: HSS-G (schnellarbeitsstahl, geschliffen) Ausführung: extra kurz (stabilere Länge, reduzierte Bruchneigung) Schaftausführung: Zylinder (passt in Standard-Bohrfutter) Typ: Typ N (Normalspirale für Metall) Farbe: blank (bright finished) Für Bohrmaschine: Handbohrmaschine Modellserie: Standard Line FAQ Wie unterscheidet sich die extra kurze Ausführung von Standardlängen? Die extra kurze Ausführung des Spiralbohrers bietet mehr Stabilität und eine geringere Bruchneigung als Standardlängen, wodurch sie besonders bei beengten Arbeitsverhältnissen und dünnwandigen Werkstücken vorteilhaft ist. Für welche Materialien ist der MetavCUT Standard Line Spiralbohrer geeignet? Der MetavCUT Standard Line Spiralbohrer aus HSS-G eignet sich für legierten und unlegierten Stahl, Gussstahl, Gusseisen, Sintereisen, Temperguss sowie Nichteisenmetalle und Hartkunststoff. Welche Vorteile bietet der 135° Spitzenwinkel in der Praxis? Ein 135° Spitzenwinkel reduziert das Wandern beim Anbohren in härteren Werkstoffen und sorgt für kürzere Anbohrzeiten sowie bessere Zentrierung bei Materialien wie Edelstahl und gehärtetem Stahl. Ist der Zylinderschaft für alle Bohrmaschinen geeignet? Der Zylinderschaft passt in gängige Dreibackenfutter von Handbohrmaschinen und Winkelbohrmaschinen, kann bei sehr hohem Drehmoment jedoch zum Durchrutschen neigen; in solchen Fällen ist ein Spannfutter mit besserer Kraftübertragung empfehlenswert. Welche Vorteile bringt die geschliffene HSS-G-Schneide konkret? Die geschliffene HSS-G-Schneide reduziert Reibung, ermöglicht schnellere Vorschübe und senkt die benötigte Anpresskraft, was die Effizienz erhöht und die Belas­tung für Maschine und Anwender vermindert.

Twist Drill — Type N, 4.2 mm, 135°, Extra short, Bright finished, HSS-G, DIN 1897 by MetavCUT The Twist Drill Type N is an extra-short HSS-G metal drill designed for hand and drilling-machine use, offering increased stability and faster drilling in confined spaces. Extra-short design for higher stability HSS-G material for robust metal drilling 135° point angle for harder workpieces Cylindrical shank fits standard chucks Conforms to DIN 1897 extra-short specification Increased Precision and Faster Drilling for Metalwork The extra-short geometry of this Twist Drill improves rigidity and reduces the risk of breakage when working with thin materials or in restricted spaces. Made from HSS-G, the bit combines wear resistance with toughness, enabling up to 40% faster drilling and requiring about 50% less feed force compared with conventional HSS drills. This leads to more consistent hole quality in alloyed and unalloyed steel, cast steels and non-ferrous metals while reducing operator effort. Better Penetration in Harder Materials With a 135° point angle, this Type N Twist Drill is optimised for harder workpieces such as stainless steel and tempered materials. The flatter point reduces chipping and shortens initial contact time, so the drill centres more reliably and requires less rework. For workshops that frequently face demanding substrates, this geometry translates directly into fewer tool changes and steadier machining results. Practical Design for Hand and Angle Drills The cylindrical shank ensures universal compatibility with standard three-jaw chucks, making the bit simple to mount in typical hand or angle drilling machines. The extra-short overall length enhances torque transmission and reduces flex during manual operation, which is particularly useful when access is limited or when drilling from awkward angles. The bright finished surface eases chip evacuation and inspection. Targeted Applications and User Benefits Designed as a classic metalworking solution, the Twist Drill Type N from MetavCUT is intended for professionals and advanced hobbyists who require reliable performance on steel, cast iron, sintered materials and hard plastics. Its robustness and ease of resharpening make it a cost-effective choice for production tasks where consistent centring and longevity are priorities. Strong recommendation: For precise metal drilling tasks choose the MetavCUT Twist Drill Type N for its extra-short stability and HSS-G performance — for further technical advice or to confirm suitability for your application, contact METAV Werkzeuge: 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp +49 170 2837271 Bezeichnung: Twist Drill Marke: MetavCUT SKU: 56042-FDA Durchmesser: 4.2 mm Spitzenwinkel: 135° Typ: Type N Ausführung: extra short Farbe / Finish: Bright finished Material: HSS-G Schaftausführung: Cylindrical Gesamtlänge: 55 mm Spirallänge: 22 mm Anwendung: Drills for metal Norm: DIN 1897 Modellserie: Standard Line Für Bohrmaschine: Drilling Machine Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials is the MetavCUT Twist Drill Type N best suited for? The MetavCUT Twist Drill Type N is primarily designed for metalworking; it performs well in alloyed and unalloyed steel, cast steel, sintered iron, non-ferrous metals and hard plastics, delivering reliable centring and efficient material removal. Is the MetavCUT Twist Drill Type N compatible with standard hand drills? Yes, the cylindrical shank of the MetavCUT Twist Drill Type N fits standard three-jaw chucks on most hand and angle drilling machines, enabling straightforward mounting and universal compatibility. For what is a Twist Drill used? The MetavCUT Twist Drill is mainly used for machining high-strength workpieces and larger bore diameters; its form is easy to sharpen and it withstands higher loads. Which 3 drill types exist? Common drill types are metal drills, wood drills and masonry/concrete drills. Why are Twist Drills sharpened? The sharpening reduces the chisel edge at the tip of the Twist Drill; by sharpening, friction forces are significantly lowered, requiring less feed force and improving centring in the workpiece. Can a Twist Drill be used to drill wood? A metal Twist Drill from MetavCUT can be used in wood but will generally guide less well and produce a less clean hole; however, it is easier to resharpen and shows lower self-feed tendency. At what drill depths is the Twist Drill most commonly used? A through-hole is typically executed with a Twist Drill; for diameters up to 20 mm and drill depths up to 100 mm the Twist Drill is the most frequently used tool. What is better, HSS or HSSE? The common belief that HSSE steels are universally superior to standard HSS is not correct; when choosing between HSS and HSSE, evaluate whether working conditions justify the higher initial cost of HSSE for your specific tasks.

Die Kombination aus Extra kurzer Bauform und HSS-G-Schliff sorgt für bis zu 40 % schnellere Bohrungen bei deutlich geringerem Anpressdruck und reduziert so Bruchrisiko und Nacharbeit. Nutzen Sie die erhöhte Stabilität und die universelle Zylinderschaft-Aufnahme für präzise Bohrungen in dünnen Blechen und Profilen; Bestellungen und technische Beratung über Metav erfolgen direkt aus Emmerich. Spiralbohrer 4,3 mm (Typ N) – extra kurz von MetavCUT Der Spiralbohrer 4,3 mm von MetavCUT ist ein extra kurzer HSS-G Metallbohrer für Handbohrmaschinen, der besonders bei engen Platzverhältnissen und dünnwandigen Werkstücken Stabilität und schnelle Bohrfortschritte bietet. Extra kurz für mehr Stabilität beim Bohren HSS-G geschliffen für schnelleres Eindringen 135° Spitze reduziert Anbohrwiderstand Zylinderschaft für universelles Spannfutter Geeignet für legierte und unlegierte Stähle Mehr Leistung bei beengten Platzverhältnissen Die Extra kurze Ausführung reduziert die Hebelwirkung und verringert die Bruchneigung bei Handgeführten Bohrmaschinen. Durch den geschliffenen HSS-G-Werkstoff werden Bohrzeiten spürbar verkürzt, während der Kraftaufwand sinkt. Die 135° Spitze erleichtert das Anbohren in härteren Werkstoffen und minimiert das Wandern des Bohrers. Dieser Vorteil macht sich insbesondere bei dünnen Blechen und Profilen bemerkbar, wo Präzision und geringe Verformung zählen. Robuste Konstruktion und universelle Aufnahme Die Kombination aus gehärtetem HSS-G, genormter DIN 1897-Ausführung und Zylinderschaft gewährleistet eine einfache Handhabung in Standard-Dreibackenfuttern. Die kurze Spirallänge erhöht die Verdrehungsfestigkeit und eignet sich daher für Arbeiten mit begrenztem Platzangebot. Anwender profitieren von einer langlebigen Schneidegeometrie, die für Legierungsstähle, Gusseisen und Nichteisenmetalle ausgelegt ist, ohne dass bei normaler Werkstattanwendung sofort Verschleißprobleme auftreten. Praxistauglichkeit, Einsatzbereiche und Hinweise Mit einem Durchmesser von 4,3 mm fällt dieser Bohrer in den Standard-Bereich für Alltags- und Werkstattarbeiten und ist für dünne bis mittlere Bleche, Profile und Flachstahl empfohlen. Bei hohem Präzisionsanspruch empfiehlt sich vorheriges Zentrieren, da Bohrer in diesem Bereich zum Wandern neigen können. Tiefe Sacklochbohrungen über das Fünffache des Durchmessers sollten vermieden werden, da die Spanabfuhr kritisch wird. Für stärkere Drehmomente ist auf sichere Spannfutterspannung zu achten, weil der Zylinderschaft bei sehr hoher Last durchrutschen kann. Greifen Sie zur MetavCUT HSS-G Lösung für präzise Metallbohrungen und fordern Sie bei Bedarf technische Beratung per E‑Mail an info@metav-werkzeuge.com oder telefonisch unter +49 2822 7131930 Produkteigenschaften Bezeichnung: Spiralbohrer Marke: MetavCUT Serie: Standard Line Norm: DIN 1897 Artikelnummer: 56043-FDA Daten Durchmesser: 4,3 mm Gesamtlänge: 55 mm Spirallänge: 22 mm Spitzenwinkel: 135° Verpackungseinheit: 10 Besonderheiten Material: HSS-G (Schnellarbeitsstahl, gehärtet) Schaftausführung: Zylinder (Rundschaft, universell spannbar) Ausführung: extra kurz (mehr Stabilität, weniger Bruchneigung) Typ: Typ N (Normalspirale für Metall) Farbe: blank (hell fertigungsglanz) Für Bohrmaschine: Handbohrmaschine Anwendung: Bohrer für Metall FAQ Welche Werkstoffe lassen sich mit dem Spiralbohrer 4,3 mm von MetavCUT bearbeiten? Der Spiralbohrer 4,3 mm von MetavCUT (Standard Line, SKU 56043-FDA) eignet sich für legierte und unlegierte Stähle, Gussstahl, Gusseisen sowie Nichteisenmetalle und Hartkunststoffe; bei sehr zähen Materialien auf geeignete Kühlung achten. Ist der Zylinderschaft des Spiralbohrers 4,3 mm für Akkubohrschrauber geeignet? Ja, der Zylinderschaft passt in gängige Dreibackenfutter von Akkubohrschraubern, jedoch ist bei hohen Drehmomenten auf feste Spannfutterspannung zu achten, da Rundschäfte bei extremer Belastung eher durchrutschen können. Warum ist die Ausführung extra kurz vorteilhaft? Die extra kurze Bauform erhöht die Verdrehungsfestigkeit und reduziert die Bruchneigung, was besonders beim Bohren in dünnwandigen Werkstücken und bei beengten Platzverhältnissen vorteilhaft ist. Welcher Spitzenwinkel ist sinnvoll für harte Werkstoffe? Der Spiralbohrer 4,3 mm verfügt über einen 135° Spitzenwinkel, der das Anbohren in härteren Werkstoffen erleichtert und das Wandern auf der Oberfläche reduziert. Gibt es spezielle Einsatzgrenzen für tiefe Bohrungen? Für den Durchmesser 4,3 mm gelten die üblichen Grenzen des Standard-Bereichs; Bohrtiefe über das Fünffache des Durchmessers wird nicht empfohlen, da die Spanabfuhr und Kühlung kritisch werden und die Bohrqualität leidet.