Twist Drill — Extra Long HSS‑G Metal Drill, Ø 10 mm, 135° Tip, Bright Finished, Fully Ground, DIN 1869 (MetavCUT Standard Line)

The Twist Drill by MetavCUT is an extra long metal drilling bit designed for deep and hard‑to‑access holes in alloyed and unalloyed steels when used with a drilling machine.

• Extra long design for deep holes
• HSS‑G material for precise metal drilling
• 135° tip angle for harder materials
• Fully ground shank for high runout accuracy
• Conforms to DIN 1869 for reliable performance

Reach deeper holes with steady guidance

The Extra Long overall length of 265 mm and a spiral length of 185 mm allow confident drilling into deep workpieces where standard lengths fall short. This design reduces the need for extensions and improves access in assemblies or when the chuck is positioned far from the work zone. For operations that require penetration beyond typical depths, the extended geometry combines reach with stable chip evacuation, keeping the Drilling Machine feed consistent and lowering the risk of breakage during long runs.

Cleaner, faster cuts in metal thanks to HSS‑G grinding

Manufactured from HSS‑G and produced with CNC grinding, the bit delivers sharp cutting edges and excellent concentricity. The ground geometry supports up to 40% faster drilling and requires 50% less axial force compared with conventional rolled HSS types, which translates into reduced operator effort and shorter cycle times on repetitive metal tasks. The result is precise holes in materials such as alloyed and unalloyed steel, cast iron and non‑ferrous metals, with superior surface quality and dimensional consistency.

Better entry and control for tough materials

A 135° tip angle improves centring and reduces walking when starting holes in harder substrates like stainless steel. The larger tip angle shortens penetration time and, when paired with the ground point, minimises friction at the cutting edges. For best results, apply appropriate cutting fluid and controlled feed rates; cooling and lubrication both extend tool life and maintain the sharpness that the ground geometry provides.

Recommended use, handling and target applications

This Standard Line bit is optimised for metalworking applications and is intended for use with a Drilling Machine under controlled conditions. The fully ground flutes afford very good chip formation and ejection, but ground HSS can be more brittle than rolled designs; therefore, stationary or well‑supported setups with steady coolant flow are advised for deep or interrupted cuts. The product suits professionals and workshops that require reliable deep‑hole performance and high hole quality in demanding materials.

Acquire the MetavCUT Standard Line Twist Drill for dependable deep metal drilling — METAV Werkzeuge provides expert technical advice and personal support via info@metav-werkzeuge.com, phone +49 2822 7131930 or WhatsApp +49 170 2837271

Technical Data for confident specification

• Bezeichnung: Twist Drill
• Marke: MetavCUT
• SKU: 32100-FDA
• Durchmesser: 10 mm
• Spitzenwinkel: 135°
• Gesamtlänge: 265 mm
• Spirallänge: 185 mm
• Ausführung: extra long
• Schaft Ausführung: fully ground
• Farbe/Oberfläche: bright finished
• Material: HSS‑G
• Norm: DIN 1869
• Modellserie: Standard Line
• Für Bohrmaschine: Drilling Machine
• Anwendung: Drills for metal
• Verpackungseinheit: 10
• Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com

FAQ

What are Twist Drills typically used for?
The MetavCUT Twist Drill is primarily applied for machining high‑strength materials and for larger diameter or deep hole drilling. Its geometry is well suited to demanding metalworking tasks, and the ground form allows precise holes and reliable performance under higher loads.

Which three drill types exist?
Common categories are Metal Drills, Wood Drills and Masonry/Concrete Drills; the MetavCUT Twist Drill belongs to the metal drill group and is engineered for steels, castings and similar hard materials.

Why are Twist Drills sharpened (pointed)?
The sharpening reduces the cross‑cut at the tip, which lowers friction and the required feed force while improving centring in the workpiece. The MetavCUT Twist Drill’s ground point therefore aids smoother starts and more accurate hole positioning.

Can a metal Twist Drill be used for wood?
A metal Twist Drill such as the MetavCUT Standard Line can be used in wood, but guidance and finish will be inferior compared with dedicated wood bits. Metal drills are easier to resharpen and exhibit less self‑feeding, which may be desirable in some manual applications.