how can i check an external thread?

Take advantage of precise, fast pass/fail checks and robust wear resistance thanks to hardened steel and DIN 7162 conformity; order the matching gauge pins directly via Metav Werkzeuge or contact our consultants for batch and inspection advice. Limit Gauge Pin — hardened-steel inspection pin, 11 mm, DIN 7162 (Filetta) The Limit Gauge Pin is a hardened-steel inspection pin designed for rapid go/no-go checks and routine dimensional control in workshops and inspection benches, compliant with DIN 7162. Hardened-steel construction for long service life Conforms to DIN 7162 for consistent tolerances 11 mm nominal diameter for standard inspection tasks Wear allowance on the good side to extend usable life Faster, reliable pass/fail inspection for production lines The compact inspection pin delivers quick go/no-go checks that reduce measuring time at control points and on the shop floor. By providing an unequivocal pass or fail condition, the pin supports efficient decision-making in both single-piece inspections and repetitive sampling routines. Conformity with DIN 7162 ensures that the nominal diameter and tolerance band are traceable to an established standard, which simplifies integration into existing inspection protocols and statistical process control. Robust build that minimises downtime Thanks to its hardened steel construction the pin withstands repeated contact without rapid degradation, while the specified wear allowance on the good side preserves the functional limit for longer. This translates into fewer replacements, reduced downtime and lower indirect costs from inspection interruptions. The hardened surface also keeps seating and mating surfaces consistent, helping to avoid false rejects that would otherwise increase rework. Practical benefits for inspection benches and gauge sets As a dedicated inspection pin, the component is optimised for quick handling and straightforward verification tasks on inspection benches and assembly jigs. The clear go/no-go characteristic reduces interpretation time for operators and speeds up routine quality checks. For quality managers the result is measurable: quicker throughput at control stations and a more consistent acceptance rate across batches. Traceability and suitability for regular quality workflows Manufactured to industry standard, the pin supports consistent batch-to-batch performance and straightforward inventory management when used in gauge sets or fixed inspection fixtures. The simple geometry and standardised tolerance regime make the item suitable for assembly audits, incoming inspections and periodic verification of tool wear, providing procurement confidence for maintenance and quality teams. Request technical advice or a batch availability check from Metav Werkzeuge in Emmerich to align delivery options with production schedules Technical Data Article number: MS911.173 Name: Limit Gauge Pin Material: hardened steel Standard: DIN 7162 Measurements / Core data Diameter: 11 mm Features / Applications Wear allowance on the good side Hardened for wear resistance Intended for go/no-go inspection tasks Category: gauge pins / inspection pins FAQ What is the nominal diameter of this inspection pin? The inspection pin has a nominal diameter of 11 mm; this specification applies to the Filetta limit gauge pin (SKU MS911.173). Is the pin suitable for go/no-go checks on assembly lines? Yes, the Filetta limit gauge pin is designed for rapid pass/fail checks and is suitable for routine assembly-line and workshop inspections. What material is used and how does it affect service life? The pin is made from hardened steel, which increases wear resistance and extends usable life compared with untreated pins. Which standard governs the pin’s tolerances? Tolerances and dimensions conform to DIN 7162, providing a recognised reference for inspection procedures. How does the wear allowance on the good side affect inspection practice? The specified wear allowance on the good side allows continued use while preserving the functional limit for a longer period, reducing unnecessary replacements Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of precise, repeatable inspection with a comprehensive set that combines hardened steel durability, fine 0.01 mm graduation and clear transport/storage in a tool trolley with a conformity certificate; order the set directly via Metav Werkzeuge or consult our specialists for application advice. Gauge Pin Set MS910.460 — hardened steel, 0.5–12 mm, Filetta The Gauge Pin Set MS910.460 is a complete inspection kit of precision gauge pins for workshop and production metrology, designed for routine go/no‑go checks, dimensional verification and assembly control Extensive set: 1151 gauge pins 0.5–12 mm Hardened steel for high wear resistance 0.01 mm graduation for precise selection Supplied in trolley with conformity certificate Reliable precision for repetitive inspection This set delivers high precision across a broad micro range, covering 0.5–12 mm with a graduation of 0.01 mm, which supports fine incremental selection during inspection procedures. The measured accuracy of 0.002 mm provides a verifiable basis for routine quality checks and contributes directly to stable production outcomes. Using hardened components reduces wear, so nominal sizes remain consistent over repeated use, limiting rework and saving time in the measurement chain. Designed to streamline workshop workflows Presented as a full kit in a purpose‑fitted tool trolley, the collection of pins is organised in individual plastic containers with size marking for rapid retrieval and immediate traceability. The integrated holders with good/reject indication simplify visual sorting and speed up go/no‑go decisions at the bench. These layout and handling choices reduce operator time per check and improve throughput without compromising measurement reliability. Robust handling with traceable conformity Constructed from hardened steel and supplied with a conformity certificate, the set emphasises longevity and documented quality assurance. Individual containers protect each gauge pin from contamination and damage, while the trolley format supports safe transport and tidy storage. The combination of durable materials and documented conformity helps maintain audit readiness and supports consistent measurement results across shifts. Versatile applications across metrology tasks Suitable for inspection, assembly verification and gauge‑based calibration work, the collection is tailored to routine tasks in production, toolmaking and inspection labs. The fine step size enables close fit control and small‑feature checks, while the extensive count of pins in the set covers a wide range of nominal sizes without the need for multiple purchases. The format is particularly useful where rapid switching between sizes and clear go/no‑go indication are required. For hands‑on advice or to secure the Filetta Gauge Pin Set MS910.460 for a stable inspection routine, contact Metav Werkzeuge — our consultants provide practical application support from Emmerich and ensure timely supply to the workshop. Technical data Article number: MS910.460 Name: Gauge pin set Manufacturer: Filetta Material: hardened steel Set: yes Accessories included: 3x holders with good/reject indicator Supplied: tool trolley with conformity certificate Packaging: pins in individual plastic containers with size marking Facts Measurement range: 0.5–12 mm Measurement increment: 0.01 mm Accuracy (nominal): 0.002 mm Pieces per set: 1151 Weight: 63 kg Dimensions (L×W×H): 670×350×540 mm Special features Hardened steel construction Individual marked containers for each pin Tool trolley delivery for transport and storage Conformity declaration included Holders with go/no‑go indicator included FAQ How fine are the increments in the set? The set provides a 0.01 mm graduation between sizes, enabling fine selection for close tolerance checks with the Gauge Pin Set MS910.460. Is the set suitable for repeated industrial use? Yes, the hardened steel pins and protective individual containers make the filetta gauge pin set appropriate for frequent workshop and production use. Does the delivery include documentation? Delivery includes a conformity certificate; the Gauge Pin Set MS910.460 is supplied with documentation confirming its compliance. Can the set be used for calibration tasks? The wide range and fine graduation allow the set to be used for inspection and informal calibration verification; for certified calibration procedures, refer to your internal quality protocols. What accessories come with the set? The set contains three holders with good/reject indication and all pins are housed in individual marked containers within the supplied trolley. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of a durable inspection solution that combines hardened steel construction, DIN 7162 conformity and a built‑in wear allowance on the good side for predictable lifetime performance; order the Filetta limit gauge pin directly via Metav Werkzeuge or contact our consultants for application guidance. Limit gauge pin MS911.175 — hardened steel, DIN 7162 by Filetta The limit gauge pin is a precision plug gauge designed for fast verification of hole diameters and dimensional conformity in production and inspection environments. Hardened steel for durability Conforms to DIN 7162 standard Nominal 13 mm gauge pin Wear allowance on the good side Fast, reliable checks for hole diameters Limit gauge pins serve as a compact and effective tool for rapid go/no‑go assessment of bore diameters and fits. The MS911.175 from Filetta allows straightforward comparison against tolerance limits, reducing the time spent on intricate measurements and lowering the risk of finishing parts that fail inspection. By applying a simple pass/fail principle, this type of gauge pin supports continuous quality control and streamlines in‑process checks, which in turn improves throughput and reduces rework rates on the shop floor. Robust construction with predictable wear behaviour Manufactured from hardened steel, the pin provides a resistant contact surface that tolerates repeated use in production environments. The specified wear allowance on the good side means that the design accounts for gradual surface loss without compromising the verification function; users gain a longer useful service life and more predictable maintenance intervals. This wear concept avoids sudden losses of conformity and simplifies decisions about replacement or recalibration, delivering tangible savings over the component lifecycle. Standards compliance for traceable inspection routines Conformity to DIN 7162 ensures that the gauge pin integrates with existing metrology routines and adheres to recognised dimensioning rules, facilitating consistent documentation and auditability. The simple form factor makes the component easy to store alongside other inspection tools and easy to use during incoming inspections or final part control. With a clear identification such as MS911.175 and manufacturer provenance, the pin is suited for repeatable batch checks and supports a traceable quality management workflow. For precise bore verification from Filetta, contact Metav Werkzeuge for ordering and tailored application advice — Metav Werkzeuge GmbH is available at info@metav-werkzeuge.com or by phone at +49 2822 7131930 to support selection and delivery. Technical data Article number: MS911.175 Manufacturer: Filetta Material: hardened steel Size: 13 mm Standard: DIN 7162 Facts Nominal size: 13 mm Special features Wear allowance on the good side Limit/plug gauge function for go/no‑go checks Category: gauge pins / plug gauges Intended for bore diameter verification FAQ What is the primary use of this limit gauge pin? The limit gauge pin MS911.175 by Filetta is intended for quick go/no‑go checks of hole diameters and basic conformity assessments in production and inspection workflows. Which material is the gauge pin made from? The Filetta gauge pin is made from hardened steel, chosen to provide wear resistance and a stable contact surface for repeated inspections. Does this gauge pin conform to recognised standards? Yes, the component conforms to DIN 7162, which supports consistent dimensional control and integration into documented inspection routines. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Combining DIN 7162 conformity, hardened steel construction and a wear allowance on the Go side yields a durable checking tool for repeatable bore inspections; order the gauge directly via Metav Werkzeuge or consult our advisers for application guidance. Limit plug gauge G7 — 3.5 mm, hardened steel (Filetta) Limit plug gauge G7 is a hardened-steel go/no-go gauge designed for rapid acceptance checks of small bores in production and quality control. Hardened steel construction Complies with DIN 7162 standard Wear allowance on the Go side Diameter 3.5 mm precision Reliable checks for small bores The limit plug gauge is intended for fast, unequivocal go/no-go inspections in the workshop and at in‑process control stations. Manufactured to DIN 7162, the tool offers standardised dimensions for consistent interchangeability across gauges and fixtures. With a nominal diameter of 3.5 mm, the gauge pin provides a compact solution for verifying small internal diameters without the need for complex measuring setups, enabling straightforward acceptance decisions and reducing inspection time. Designed to maintain accuracy and lifetime Constructed from hardened steel, the gauge resists wear and mechanical damage during repetitive use, which secures measurement stability over many cycles. The specified wear allowance on the Go side compensates for gradual material loss at the contact zone: this means the initial pass/fail boundary is conservatively set so that the Go end remains reliable as the gauge accumulates wear, thereby extending the service life and reducing replacement frequency. Such design reduces process interruptions and supports predictable maintenance planning. Practical integration into production and inspection routines As a dedicated measuring pin, the device integrates easily into gauge sets, test benches and handheld Go/No‑Go routines; the compact geometry allows quick handling and minimal fixturing. The simple acceptance logic of a limit plug gauge shortens operator training and accelerates throughput in inspection loops, delivering measurable time savings. For specific application scenarios or assistance with fixture compatibility, Metav’s technical advisers can provide pragmatic recommendations tailored to production needs. For standard-compliant bore checks and tailored application advice, order the Filetta limit plug gauge G7 via Metav Werkzeuge or contact our Emmerich team at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: MS911.163 Manufacturer: Filetta Product: Limit plug gauge G7 Facts Diameter: 3.5 mm Standard: DIN 7162 Special features Material: hardened steel Wear allowance on the Go side Category: gauge pins / measuring pins FAQ What is the primary purpose of this limit plug gauge? The Filetta limit plug gauge G7 (MS911.163) is used for quick go/no-go inspections of small internal diameters to support fast acceptance decisions in production and quality control. Which standard does the gauge comply with? The gauge is manufactured to DIN 7162, ensuring standardised dimensions and compatibility with conventional metrology practices. What material is the gauge made from and why is that important? This limit plug gauge is made of hardened steel, which improves wear resistance and maintains functional tolerances during repetitive use. What does "wear allowance on the Go side" mean in practice? The wear allowance on the Go side means the Go end is dimensioned to allow a controlled amount of wear before it affects pass/fail decisions, extending the gauge’s usable life while preserving inspection reliability. Can this gauge be used on a shop floor for routine checks? Yes, the compact 3.5 mm gauge pin is suitable for routine shop‑floor Go/No‑Go checks and can be incorporated into simple test fixtures or handheld inspection procedures. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of precise pass/fail inspection, rugged hardened steel construction and clear compliance with DIN 7162 for reliable throughput in production control; order the limit gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Limit gauge pin G7 — 9 mm, hardened steel, DIN 7162 Limit gauge pin G7 for rapid go/no-go verification in machining and inspection environments, designed to simplify batch acceptance and reject decisions. Hardened steel construction DIN 7162 compliant 9 mm nominal diameter Wear allowance on the go side Fast, objective pass/fail inspection for production lines A compact inspection tool engineered for decisive checks, the limit gauge pin provides a straightforward go/no-go result that removes ambiguity from routine quality control. Manufactured from hardened steel and produced to DIN 7162 tolerances, the pin gives repeatable contact geometry and low variation between checks. The simple plug-style design shortens inspection cycles and reduces handling time, helping to maintain throughput without sacrificing measurement integrity. Robust design that keeps maintenance intervals long The combination of hardened material and a defined wear allowance on the go side minimises in-service degradation and extends service life. The wear allowance compensates for gradual material loss where contact is most frequent, so the pin continues to represent the required acceptance limit for longer. As a result, tool replacement intervals are extended and unplanned downtime for gauge renewals is reduced, supporting smoother production schedules and lower indirect costs. Practical compatibility and clear traceability for inspection routines Suitable for quick hole and bore acceptance tests across general machining, assembly and incoming inspection, this plug gauge integrates easily into standard inspection kits. The nominal 9 mm size is instantly recognisable and compatible with common fixture layouts; identification is simplified by the SKU MS911.171 and clear marking. For workshop procurement and quality documentation, the robust construction and standardised dimensioning deliver dependable evidence for conformity assessments and sampling plans. Contact Metav Werkzeuge for Filetta G7 limit gauge pin availability, application guidance and order placement — expert advice from our Emmerich team ensures the correct plug gauge for each inspection task Technical Data Article number: MS911.171 Manufacturer: Filetta Material: hardened steel Standard: DIN 7162 Facts Nominal diameter: 9 mm Type: limit gauge pin (go/no-go principle) SKU: MS911.171 Special features Wear allowance on the go side (Abnutzungsaufmaß der Gutseite) Suitable for plug-type acceptance tests Compact, transfer-friendly design FAQ What nominal size does this plug gauge represent? The Filetta limit gauge pin is specified with a nominal diameter of 9 mm (SKU MS911.171), suitable for standard hole acceptance checks. Which material and standard apply to this gauge? This plug gauge is made from hardened steel and manufactured to DIN 7162, ensuring consistent contact geometry and conformity to recognised metrology standards. How does the wear allowance affect service life? The wear allowance on the go side prolongs usable life by compensating for gradual wear at the contact surface, so the gauge retains its acceptance function longer between replacements. Is the pin suitable for production inspection routines? Yes; the plug gauge is intended for rapid go/no-go verification in machining, assembly and incoming inspection, offering clear pass/fail decisions and easy integration into inspection kits. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of precise, rapid thread identification combined with a lightweight, corrosion‑resistant design for smoother assembly and inspection workflows. The set’s anodised aluminium gauges and organised plastic case enable fast checks of common metric threads; order directly via Metav Werkzeuge or contact our consultants for technical advice. Gewindekontrollsatz MS910.425 — Thread gauge set (anodised aluminium, metric) by Filetta The Gewindekontrollsatz is a compact identification set for metric internal and external threads, intended for workshop inspection, maintenance and assembly tasks Anodised aluminium construction For metric internal and external threads Supplied in a durable plastic case 20-piece set covering M3–M24 Faster thread identification for everyday production The gauge set accelerates routine identification and basic verification of metric screw threads, reducing time lost on uncertain assembly decisions. Thanks to the wide size range from M3 to M24 and the inclusion of both internal and external gauges, common pitches and diameters can be checked on the spot. The primary benefit is operational efficiency: fewer stoppages during assembly and faster throughput in inspection processes. The solid, repeatable fit of each gauge supports reliable visual and tactile confirmation of thread form and pitch. Lightweight, corrosion‑resistant construction for frequent handling Being manufactured from anodised aluminium, the components combine durability with low weight, making them comfortable for daily use in bench and field environments. The surface treatment helps resist wear and corrosion, preserving the profile of each gauge and extending service life. Packaged in a plastic case that keeps items organised and protected, the set is easy to transport between workstations and to store without risk of damage to the thread contours. This construction promotes consistent handling with minimal maintenance. Practical scope for incoming inspection and maintenance The set is designed as a practical aid for incoming goods inspection, routine maintenance and quick on‑machine checks. It is intended for identification and coarse verification rather than micrometric measurement: the gauges confirm thread form and common pitch compatibility to avoid assembly errors. For workshops that need straightforward, rapid decisions—accept, reject, or select the correct fastener—this solution reduces rework and saves time in quality control routines while supporting a smooth production flow. Clear contents and metric compatibility for everyday sizes Contents include gauges for standard metric sizes that are frequently encountered in mechanical and electrical assemblies. The 20‑piece composition covers a typical workshop spectrum from smaller machine screws up to larger bolts used in fixtures and assemblies. This configuration makes the set suitable as a bench reference or as part of a mobile inspection toolkit, supporting technicians who require quick identification without complex measurement equipment. The lightweight profiles and organised layout aid rapid selection and return to service. For reliable metric thread identification from Filetta choose Metav Werkzeuge — contact our Emmerich specialists for tailored advice and fast supply via info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical Data Article number: MS910.425 Manufacturer: Filetta Material: anodised aluminium Thread type: metric Set: 20 pieces Facts Sizes included: M3x0.5, M4x0.7, M5x0.8, M6x1.0, M8x1.0, M8x1.25, M10x1.0, M10x1.25, M10x1.5, M12x1.25, M12x1.5, M12x1.75, M14x1.5, M14x2.0, M16x1.5, M16x2.0, M20x1.5, M20x2.5, M24x2.0, M24x3.0 Suitable for: internal and external threads Special features Identification and basic verification of metric threads Lightweight, corrosion‑resistant anodised finish Supplied in a protective plastic case Compact, workshop‑oriented organisation FAQ What is the primary purpose of this gauge set? The Gewindekontrollsatz MS910.425 by Filetta serves for quick identification and basic verification of metric internal and external threads to support inspection and assembly decisions. Can the gauges measure thread tolerances precisely? The set is intended for identification and coarse verification rather than precision tolerance measurement; for high‑accuracy checks, use calibrated metrology instruments. Which sizes are covered by the set? The set contains 20 gauges covering common metric sizes from M3x0.5 up to M24x3.0, suitable for many workshop and maintenance tasks. Is the material suitable for frequent workshop use? Yes — the gauges are made from anodised aluminium, providing a balance of lightweight handling and corrosion resistance for regular use. Does the set include a case for transport and storage? The Filetta MS910.425 is supplied in a durable plastic case that keeps each gauge protected and organised for transport between workstations. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of the combination of wide standard coverage, clear dimension data and compact shop-floor usability to speed up design and inspection tasks; order the thread chart via Metav Werkzeuge or ask our consultants for application advice. Filetta Thread Chart – comprehensive thread dimension reference, clear-format A Filetta Thread Chart that provides an immediate overview of thread dimensions across common international systems, intended as a compact reference for design, production and inspection. Universal lookup for Metric, UNC, UNF, BSW Clear dimensions for Gas and BA threads Compact format for shop-floor reference Useful for design, inspection and procurement Fast decisions with consolidated thread data The core benefit of this reference is the consolidation of many standards into a single sheet. The chart lists sizes and key dimensions for metric, BSW, Gas, BSF, Pg, BA, UNC, UNF, UNEF, EG-M and EG-MF, enabling rapid decisions during setup and verification. By combining these standards, the table reduces the need to consult multiple manuals and supports faster tool selection and drawing checks. Clear labelling and organised columns turn otherwise time-consuming lookups into a quick verification step, which improves shop-floor throughput and reduces machine idle time. Improved accuracy for manufacturing and inspection Having standard dimensions collated in one reference lowers the risk of specification errors when producing threaded parts. The chart highlights pitch, nominal diameters and common conversions, making it straightforward to match taps, dies and mating components. This logical presentation supports quality control routines and assists inspectors in cross-checking parts against the correct standard. Presented as a compact, easy-to-read layout, the reference helps maintain measurement integrity without complex interpretation, supporting reliable outcomes in both small-series manufacturing and routine maintenance. Practicality for engineers, buyers and technicians Designed to serve multiple roles, the table is a practical tool for designers verifying thread fits, for procurement teams specifying the correct fasteners, and for technicians performing assembly checks. The compact format is suited to the toolroom, drawing office or bench, meaning the information is available where decisions are actually taken. With its focus on usability, the reference speeds up specification workflows and contributes directly to process efficiency—an economical improvement in daily operations. Clear communication between teams and suppliers Standardised references reduce misunderstandings between design, production and suppliers. Using one authoritative chart for common thread forms creates a single source of truth that simplifies ordering and reduces returns due to mismatched threads. The clear mapping of thread types and sizes supports consistent documentation in technical drawings and procurement lists, improving collaboration across departments and with external partners. Contact Metav Werkzeuge today for procurement support, bulk orders or specific format requests for the Filetta Thread Chart (SKU MS835.162) — expert advice and reliable delivery from Emmerich are available to help integrate this reference into your workflow Technical Data Article number: MS835.162 Name: Thread Chart (Gewindetabelle) Manufacturer: Filetta UID: MS835.162 Facts Standards included: Metric, BSW, Gas, BSF, Pg, BA, UNC, UNF, UNEF, EG-M, EG-MF Purpose: Quick lookup of thread dimensions and pitches Intended use: Design checks, inspection reference, procurement specification Special features Consolidated display of multiple international thread systems Compact, shop-floor friendly format Suited for engineers, inspectors and purchasing staff FAQ Which thread standards are covered in the chart? The chart lists common standards including metric, BSW, Gas, BSF, Pg, BA, UNC, UNF, UNEF, EG‑M and EG‑MF for immediate comparison. Is this chart suitable as a shop-floor reference? Yes, the Filetta Thread Chart (SKU MS835.162) is designed for quick lookups at the bench or in the toolroom and is optimised for practical use by technicians and inspectors. Can the table be used for procurement specifications? The consolidated dimensions and standard identifiers make the chart appropriate for clear procurement documentation and ordering lists. Does the chart include pitch and nominal diameter data? Yes, the presentation includes key dimension data such as pitch and nominal diameters to aid fitting and tool selection. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Combine ISO 286‑2 compatibility with an instant lookup of more than 6,400 tolerance values for reliable design decisions and consistent inspection results — order the Tolerance table directly via Metav Werkzeuge or contact our consultants for tailored advice. Tolerance table — ISO 286‑2 reference chart (up to 500 mm) by Filetta The Tolerance table is a compact reference chart for immediate reading of tolerance values and fits according to ISO 286‑2, intended for engineering, quality control and workshop use. ISO 286‑2 compatibility up to 500 mm Over 6,400 tolerance entries Immediate reading for fits and tolerances Suitable for internal and external dimensions Faster decisions with standardised tolerance data The reference matrix provides a single, standardised source for clearance, transition and interference fits, reducing time spent searching dispersed tables. With direct mapping to ISO 286‑2 and coverage to 500 mm, the chart supports rapid verification of nominal sizes and tolerances, enabling engineers to confirm fit classes and tolerance zones without complex calculations. The compact presentation of tolerance values accelerates decision-making in design reviews and first-off inspections. Clear guidance for assemblies and inspection routines Presented as an immediate-reading table, the chart removes ambiguity when selecting shaft and hole tolerances for bearings, housings or shafts. The organised layout helps translate ISO class designations into usable limits for production and QC, so tolerance checks can be executed consistently on the shop floor. Where traceable documentation is needed, the dataset of 6,400+ entries serves as a reliable reference for specifying fits in drawings and inspection protocols. Practical benefits for workshops and design offices Adopting a single reference chart reduces errors caused by cross-referencing multiple sources and supports faster training of technicians and junior engineers. The concise format is optimised for routine tasks — from tolerance verification during assembly to prepare-for-inspection checks — and complements digital workflows where a human-readable standard is required alongside CAD and measurement reports. The association with Filetta denotes a focused tool for metrology professionals who value clarity and compliance. For standards-compliant tolerance reference and rapid integration into inspection routines, request the Filetta Tolerance table from Metav Werkzeuge today — contact our specialists at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability for specific applications. Technical Data Article number: MS835.163 Name: Tolerance table Brand: Filetta Label: Toleranztabelle Facts Standard: ISO 286‑2 Scope: up to 500 mm Entries: >6,400 tolerance values Special features Immediate-reading table of tolerance values and fits Includes internal and external dimensions Data suited to engineering and workshop reference FAQ What standard does this reference follow? The Filetta Tolerance table follows ISO 286‑2, providing standardised tolerance classes and zones for engineering use. Up to which nominal size are tolerance values provided? The chart covers nominal sizes up to 500 mm, with entries for both internal and external dimensions. How extensive is the dataset included in the chart? The reference contains more than 6,400 tolerance values for quickly determining fits and limits. Is this chart suitable for shop‑floor inspection tasks? Yes — the immediate‑reading format makes the chart suitable for routine inspection, assembly checks and specification clarification in the workshop. Can the table help when specifying fits on technical drawings? The dataset translates ISO class designations into practical limit values, supporting clear specification of fits and tolerances on drawings. Filetta: Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com