What is used to measure micrometers?

Precision blind‑hole inspection is facilitated by the combination of a self‑centring three‑point head, carbide measuring faces and an accuracy of ±0.005 mm; order the MS908.663 via Metav Werkzeuge or consult our advisors for specification support. MS908.663 — three‑point internal micrometer with self‑centring head and ±0.005 mm accuracy (Metav IndustryLine) A self‑centring three‑point internal micrometer MS908.663 designed for fast, repeatable measurement of blind holes in workshop and production environments. Self‑centring three‑point measuring head Accuracy ±0.005 mm for repeatable results Carbide measuring faces for long service life Delivered in a protective transport case Precise blind‑hole measurement with minimal operator error The three‑point measuring concept produces a natural centre‑finding action that stabilises the instrument inside a blind hole, reducing eccentricity and operator influence. With an analogue reading of 0.005 mm and an accuracy of ±0.005 mm, this gauge is suited to quality‑critical internal diameter checks where small deviations matter. The vernier‑style scale enables direct mechanical reading without reliance on batteries or electronics, supporting uninterrupted inspections on the shop floor. This combination of mechanical reliability and fine resolution promotes consistent pass/fail decisions during incoming inspection and first‑off checks. Built for demanding workshop use and long‑term repeatability Constructed with carbide measuring faces, the instrument resists wear in daily use and preserves measuring integrity over longer service intervals. The instrument’s physical length of 145 mm and measuring span of 100–125 mm places it in the standard measuring range for general machine‑shop applications, offering a practical balance between reach and rigidity. The robust design and hardened contact surfaces make the micrometer tolerant of routine handling; the supplied protective transport case reduces the risk of damage during storage and transit, keeping calibration stability intact. Practical advantages for process control and inspection routines Using a self‑centring, three‑point internal gauge streamlines internal diameter checks in blind holes, bores and recesses, enabling faster set‑ups at the bench or on the machine. The instrument’s repeatable seating and fine resolution help to reduce scrap and rework by catching dimensional drift earlier in the process. As an analogue instrument it integrates easily into established measurement routines and inspection sheets, while its mechanical simplicity minimises downtime compared with devices that rely on electronics. Typical applications and handling guidance The micrometer is intended for blind‑hole and internal diameter measurements in general engineering, toolroom checks and production quality control. For best results, ensure clean contact surfaces and a stable seating in the bore before taking a reading; the three‑point head will centre itself, but careful alignment reduces measurement scatter. Periodic verification against a gauge block or master ring is recommended to confirm ongoing accuracy and to schedule recalibration when necessary. The instrument’s durability and simple operation make it a practical choice for repetitive internal measurements on ferrous and non‑ferrous components. For reliable blind‑hole inspection with Metav IndustryLine precision, contact Metav Werkzeuge for purchase and expert advice by email at info@metav-werkzeuge.com or by telephone on +49 2822 7131930 Technical data Article number: MS908.663 Name: Three‑point internal micrometer Brand: Metav IndustryLine Type: Analogue internal measuring instrument Numbers / Core technical data Measuring range: 100–125 mm Measuring length: 145 mm Reading / Resolution: 0.005 mm Accuracy: ±0.005 mm Special features / Design Self‑centring three‑point measuring head Carbide measuring faces Delivered in a protective transport case Suitable for blind‑hole (blind bore) measurement FAQ How does the three‑point head help with blind‑hole measurement? The three‑point geometry of the MS908.663 automatically centres inside a blind hole, reducing eccentricity and improving repeatability of internal diameter readings. What level of accuracy and resolution can be expected? The instrument provides a resolution of 0.005 mm with an accuracy of ±0.005 mm, making it suitable for tight tolerance internal checks in production and workshop environments. Is the gauge suitable for frequent workshop use? Yes; the carbide measuring faces and robust mechanical construction are designed for daily inspection tasks and extended service life. Can this micrometer measure other internal features besides blind holes? While optimised for blind holes, the instrument can be used for internal diameter checks, recesses and similar internal features where the three‑point contact can seat reliably. What is included with the instrument on delivery? The MS908.663 is supplied complete with a protective transport case to protect the gauge during storage and transport. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of precise three-point measurement, wireless data output with USB, and full ISO 17025 calibration for dependable bore inspection and traceable results; order via Metav Werkzeuge or consult the specialists for application advice. Three-point internal micrometer — digital, 100–150 mm measuring range, Wireless + USB, Microtech Metrology The Three-point internal micrometer is a digital, workshop-ready instrument for repeatable bore and internal diameter checks from 100 to 150 mm, designed for production quality control and laboratory verification. ISO 17025 calibration certificate included Wireless and USB data output Colour 1.5" touchscreen display High repeatability: 0.004 mm accuracy Reliable measurement where it matters The instrument delivers consistent three-point measurement across bores, reducing orientation error and improving repeatability compared with single-point probes. With a specified accuracy of ±0.004 mm, the device supports quality control procedures that demand tight tolerances. The standard-sized measuring range classifies the tool for typical workshop and machine‑shop applications, offering a practical balance between reach and rigidity for medium-sized components. Fast data capture and traceability for production Equipped with Wireless and USB data outputs and a Colour 1.5" touchscreen, the device streamlines data acquisition and logging without manual transcription. The high-resolution reading (0.0001 mm) ensures fine increments are visible on the display, while digital output supports integration into measurement software or SPC workflows. This lowers administrative effort and helps maintain a clear audit trail for batch releases. Practical handling that reduces operator influence The included adjustment ring simplifies zeroing and routine checks, and the three-contact measuring head minimises tilting errors during insertion into bores. A measuring depth of 250 mm allows access to deeper cavities while preserving stability. These ergonomic and mechanical details reduce the effect of operator technique on the measurement result, improving reproducibility across shifts. Certified delivery and industrial readiness This micrometer is supplied fully calibrated to ISO 17025 standards and includes a calibration certificate, making it immediately suitable for accredited quality environments. The combination of high accuracy, digital interfacing and certified calibration positions the instrument as a reliable tool for incoming inspection, in‑process checks and final acceptance testing. Contact Metav Werkzeuge for tailored advice and secure a certified Microtech Metrology three-point internal micrometer (SKU 133715010) with ISO 17025 calibration for your measurement process Technical data Article number: 133715010 GTIN: 4061905074295 Manufacturer: Microtech Metrology ECLASS: 21170335 ETIM: EC003590 Facts Measuring range: 100–150 mm Resolution (reading): 0.0001 mm Accuracy: ±0.004 mm Measuring depth: 250 mm Digital display: Colour 1.5" touchscreen Data output: Wireless + USB Calibration: ISO 17025 certificate included Special features Three-point internal measurement Adjustment ring included Digital operation for SPC integration Suitable for workshop and lab use Delivered calibrated for traceability FAQ Is this instrument supplied calibrated? Yes. The Microtech Metrology three-point internal micrometer (SKU 133715010) is delivered fully calibrated to ISO 17025 and includes the corresponding calibration certificate. Which measurement range does the instrument cover? The device covers a measuring range of 100–150 mm, which places it in the standard class for workshop and machine‑shop bore inspection tasks. How are measurement results exported? Measurement data can be exported either wirelessly or via USB, enabling direct transfer into inspection software or SPC systems from the Microtech Metrology instrument. What resolution and accuracy can be expected? The display resolution is 0.0001 mm and the specified accuracy is ±0.004 mm, suitable for stringent dimensional checks in production control. Is the touchscreen suitable for use with gloves? The 1.5" colour touchscreen provides clear readout and simple menus; for glove operation, common shop gloves may limit sensitivity—repeatable results are maintained via the device’s stable mechanical design. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools

The combination of precise self‑centring contact, a compact 10–12 mm measuring range and robust carbide faces ensures fast, repeatable blind‑hole measurements with minimal setup. Order the instrument directly via Metav Werkzeuge or consult the team for application advice. Metav IndustryLine Three‑Point Internal Micrometre MS908.652 — self‑centring, 10–12 mm range The Three‑Point Internal Micrometre MS908.652 is a compact analogue micrometre designed for precise diameter measurement inside blind holes and small bores in the 10–12 mm range. Self‑centring three‑point contact Measuring range 10–12 mm Accuracy 0.004 mm Carbide measuring faces Reliable centring for blind‑hole measurement A three‑point contact ensures rapid and reproducible alignment in blind holes, reducing repositioning time and measurement scatter. The micrometre’s self‑centring mechanism automatically locates the bore centre, so the operator obtains a consistent contact geometry on each measurement. With a measuring span of 10–12 mm the instrument is tailored to micro components and small bores where repeatability and short setup times are essential, improving throughput in small‑part inspection tasks. Durable contact surfaces for longer service life The measuring faces are manufactured as carbide contacts to resist wear and preserve accuracy during frequent use. The unit’s analogue design gives a tactile feel and straightforward reading, paired with a fine adjustment capability to approach tight fits carefully. The compact body (length approx. 54.5 mm) is suited to constrained access, while a setting ring (size 10) is included for verification and quick zeroing, supporting stable traceability in routine quality checks. Practical workflow advantages and workshop integration This three‑point micrometre combines simple operation with technical reliability: measurements are quick, calibration checks are straightforward and the tool integrates easily into existing inspection benches. Classified in the Micro range (max. 10–100 mm), it fulfils typical needs of precision engineering, watchmaking and small‑component production where stiffness, reach and single‑hand operation must be balanced. Metav’s distribution ensures European stock and reliable delivery from Emmerich. Request application guidance or order details from Metav Werkzeuge for the Metav IndustryLine three‑point internal micrometre MS908.652 — contact info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: MS908.652 Brand: Metav IndustryLine Category: Micrometres Type: Three‑point internal micrometre Measuring range: 10.0–12.0 mm Minimum range: 10 mm Maximum range: 12 mm Accuracy: 0.004 mm Length: 54.5 mm Setting ring: 10 Self‑centring three‑point contact Carbide (hard metal) measuring faces Analogue operation (nonius style) Suitable for blind‑hole bores FAQ How does the three‑point contact improve measurement in blind holes? The three‑point geometry of the MS908.652 centres automatically in a bore, giving a stable contact triangle that reduces wobble and improves repeatability compared with single‑point probes. What measurement accuracy can be expected from this instrument? The instrument is specified with an accuracy of 0.004 mm; in routine use this delivers repeatable diameter readings for small‑bore inspection tasks. Is the micrometre suitable for workshop use or only for laboratory conditions? Designed for practical workshop use, the robust carbide faces and analogue adjustment make the MS908.652 resilient to frequent handling while keeping measurement quality high. How is the instrument returned to zero or checked on site? A setting ring (size 10) is provided for quick verification and zeroing of the micrometre before inspection runs. Which components and applications benefit most from this micrometre? Small bores, precision fittings, watch‑ and micro‑mechanical parts and any blind‑hole diameters in the 10–12 mm range benefit from the compact form, self‑centring contact and carbide faces of the MS908.652. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Benefit from the combination of three-point contact stability, a colour touchscreen readout and ISO 17025 traceable calibration to secure reproducible internal measurements in the 10.0–12.0 mm range. Order the Three‑Point Internal Micrometer directly via Metav Werkzeuge or consult our specialists for integration advice. Three‑Point Internal Micrometer — digital instrument with Wireless + USB (Microtech Metrology) The Three‑Point Internal Micrometer is a precision instrument for stable internal diameter measurement in small bores, suitable for quality control and bench metrology in workshops and production. Three-point contact for stable internal measurements Colour 1.5" touchscreen for clear readouts Wireless and USB data output for traceable transfer Delivered calibrated to ISO 17025 with certificate Dependable accuracy where tight tolerances matter The instrument combines a three-point contact measuring head with a high‑precision mechanism to reduce runout and centring error, delivering an accuracy of ±0.004 mm across its measuring span. With a measuring range of 10.0–12.0 mm, this device is aimed at fine internal dimensions where repeatability and a low measurement uncertainty are decisive. The robust contact geometry and confirmed specification make it well suited to small‑bore inspection tasks in component finishing and final inspection workflows, supporting a rational decision process for integrating metrology into production control. Seamless data capture for quality documentation Digital measurement is presented on a Colour 1.5" touchscreen for fast reading and reduced interpretation errors; the unit also provides Wireless and USB data output for direct transfer into SPC systems or inspection software. Combined with the included calibration trace, this workflow supports rapid documentation and traceability. The instrument’s readable display and straightforward data export reduce process steps and the risk of transcription mistakes, promoting efficiency and error‑resilient quality reporting in serial inspection and laboratory environments. Practical design for everyday workshop use A compact measuring head with an extended measuring depth of 154 mm keeps handling comfortable while reaching into bores and recesses. A setting ring is included to simplify zeroing and periodic checks. Delivered fully calibrated to ISO 17025, the micrometer arrives with a formal calibration certificate, providing immediate confidence for compliance audits and internal quality routines. The combination of robust measuring geometry, clear digital feedback and certified calibration supports both operational ease and trustworthy results, reinforcing productive workflows and peace of mind in routine inspections. For traceable high‑precision internal measurement solutions from Microtech Metrology, contact Metav Werkzeuge for ordering and application support — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 133701210 GTIN: 4061905074202 Manufacturer: Microtech Metrology Numbers Measuring range: 10.0–12.0 mm Measuring depth: 154 mm Accuracy: ±0.004 mm Resolution/readout: 0.0001 mm Special features Digital display: Colour 1.5" touchscreen Data output: Wireless and USB Setting ring: included Delivered calibrated to ISO 17025 with certificate FAQ Is the instrument delivered with a calibration certificate? Yes. The Three‑Point Internal Micrometer from Microtech Metrology is supplied fully calibrated to ISO 17025 and includes the calibration certificate for traceability. What measurement range is covered by this micrometer? The device covers internal diameters from 10.0 to 12.0 mm and is designed specifically for high‑precision work within that span. How is measured data transferred to a PC or quality system? Measurement results can be exported via both Wireless and USB connections, enabling straightforward integration into inspection software and SPC workflows. What advantage does the three‑point contact offer? Three contact points centre in the bore automatically, reducing eccentricity and improving repeatability compared with two‑point methods, which is why this geometry is preferred for small‑bore internal measurements. Can the micrometer reach recessed bores? Yes. The instrument’s 154 mm measuring depth allows access to deeper internal features while maintaining the necessary measurement stability. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools

Take advantage of the combination of self-centring three-point contact, hardened measuring faces and a protective case for reliable, repeatable blind-bore measurement; order directly via Metav Werkzeuge or request advice from our technical consultants. Three-point internal micrometer MS908.664 — self-centring design, 125–150 mm (Metav IndustryLine) The Three-point internal micrometer MS908.664 is a precision instrument for accurate measurement of blind bores and internal diameters in machine shops and inspection benches Self-centring three-point contact Accuracy ±0.005 mm Hardened measuring faces Supplied in protective case Consistent concentric measurement where it matters The instrument’s self-centring three-point contact mechanism converts small radial differences into a single, centred datum, ensuring high repeatability during blind-bore checks. With a mechanical resolution and accuracy of ±0.005 mm, the device supports tight tolerance verification and process control for internal diameters. This level of precision is particularly useful when comparing series parts or validating internal fits, as the three-point geometry minimises eccentricity and reduces operator-induced variation. Robust construction for repetitive workshop use A durable construction and hardened measuring faces protect the contact points from wear and maintain measurement integrity over prolonged use. The analogue, mechanical drive reduces complexity and avoids battery dependence, making the tool suitable for routine quality inspections on the shop floor. The overall length of 145 mm gives the reach required for its measurement range while keeping the instrument compact enough for stable handling during repeated checks. Ideal balance of reach and stiffness for standard applications Classified in the standard range for internal measurement instruments (125–150 mm), this micrometer offers the best compromise between measuring reach and structural rigidity. That balance is critical in metalworking and fixture assembly, where longer tools can introduce deflection and shorter tools lack coverage. The design is optimised for blind bores, providing reliable access and reproducible contact even when full through-access is not available. Delivered protected and ready for transport The instrument is supplied in a protective case to safeguard measuring faces and the mechanism during transport and storage. Built for regular inspection cycles, it integrates easily into workshop tool sets and measurement benches; its analogue readout is simple to interpret and maintain, supporting efficient quality routines without complex electronic calibration procedures. Contact Metav Werkzeuge for tailored advice on the Metav IndustryLine three-point internal micrometer MS908.664 and to arrange procurement or technical specification support; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: MS908.664 Manufacturer: Metav IndustryLine Type: Three-point internal micrometer Feature: Self-centring Measuring range: 125–150 mm Length: 145 mm Accuracy: 0.005 mm Reading: 0.005 mm Mechanism: Analogue Delivery: protective case Measuring faces: hardened Suitable for: blind bores Numeric data Measurement range: 125–150 mm Maximum measurement: 150 mm Minimum measurement: 125 mm Accuracy/resolution: 0.005 mm Length: 145 mm SKU: MS908.664 Design and special features Self-centring three-point contact Hardened measuring faces for wear resistance Analogue drive for low maintenance Compact length for stable handling Supplied in protective case for transport Intended for blind-bore measurement FAQ What measurement range does the instrument cover? The instrument covers a measurement range of 125–150 mm, placing it in the standard workshop range suitable for many machine‑building and metalworking applications; refer to MS908.664 for exact limits. What accuracy and resolution are specified? The device offers an accuracy and reading resolution of 0.005 mm, enabling reliable checks against typical tight tolerance requirements. Is the design suitable for blind bores? Yes — the self-centring three-point contact is engineered specifically to measure blind bores with improved concentricity and repeatability. Are the measuring faces wear-resistant? The measuring faces are hardened to resist wear and maintain consistent contact geometry during repetitive inspection tasks. Is a protective case included? The instrument is supplied in a protective case to secure the micrometer during transport and storage. Is the micrometer digital or analogue? This is an analogue instrument with a mechanical drive and a direct, tactile measuring feel appropriate for workshop environments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of precise 0.004 mm accuracy, a self‑centring three‑point measuring head and carbide measuring faces for consistent blind‑hole measurement; order directly via Metav Werkzeuge or contact the consultancy team for tailored advice. MS908.656 Three‑Point Internal Micrometer — Self‑centring, 25–30 mm range (Metav IndustryLine) A three‑point internal micrometer designed for accurate measurement of blind holes and restricted bores in the 25–30 mm range, combining a compact form with stable contact geometry. Three‑point self‑centring measuring head Measuring range 25–30 mm Carbide measuring faces for wear resistance Analogue drive with 0.005 mm resolution Consistent results for blind‑hole inspection The instrument's self‑centring three‑point system guarantees repeatable contact with bore surfaces, reducing setup variance and rework in production inspection. The compact contact geometry suits restricted bores where standard callipers cannot reach, while the analogue drive and fine spindle allow controlled approach to the measuring surfaces. This configuration translates directly into fewer rejected parts and more reliable pass/fail decisions on the shop floor. Precision that meets workshop demands With a documented accuracy of 0.004 mm and a readable resolution of 0.005 mm, the device sits between general workshop tools and high‑precision instruments. The mechanical design and robust spindle ensure stable readings even in routine quality control. For applications that require exact internal diameters in small assemblies, this micrometer provides a balance of sensitivity and practical handling without invoking complex electronic systems. Durable contact surfaces for long service life The measuring faces are made from carbide, offering superior wear resistance under frequent use and abrasive conditions. That hard contact material preserves the reference geometry over many cycles and keeps measurement uncertainty low. An adjustment ring marked 25 assists with quick reference when setting or checking the nominal diameter, making repetitive tasks more efficient and less error‑prone. Compact format for fine mechanical work Classified in the micro range by its 25–30 mm span, the tool is ideal where small, precise components are involved. The short overall length supports handling in confined environments and maintains torsional stiffness for reliable contact pressure. As an analogue internal measuring instrument, it offers familiar operation for technicians while delivering the benefits of a three‑point system designed specifically for blind‑hole measurement. For precise and repeatable blind‑hole measurement, contact Metav Werkzeuge to request the Metav IndustryLine three‑point internal micrometer MS908.656 or to speak with a specialist at info@metav-werkzeuge.com / +49 2822 7131930 Technical Data Article number: MS908.656 Name: Three‑point internal micrometer Manufacturer: Metav IndustryLine Facts Measuring range: 25–30 mm Resolution: 0.005 mm Accuracy: 0.004 mm Length: 90 mm Special features Self‑centring three‑point measuring head Carbide measuring faces Analogue micrometer design Adjustment ring marked 25 Suitable for blind‑hole measurement FAQ What measuring range does this instrument cover? The three‑point internal micrometer MS908.656 covers a measuring range of 25–30 mm, suited to small‑bore and blind‑hole applications. Is this micrometer suitable for blind‑hole measurement? Yes, the self‑centring three‑point system of the Metav IndustryLine three‑point internal micrometer is specifically designed to measure blind holes and restricted bores reliably. What accuracy and resolution can be expected? The instrument provides an accuracy of 0.004 mm with an analogue readable resolution of 0.005 mm, offering precise control for workshop inspections. Are the measuring faces durable for repeated use? The measuring faces are made of carbide, ensuring wear resistance and long‑term stability of the contact geometry under frequent measurement cycles. How is the instrument adjusted for repetitive tasks? An adjustment ring marked 25 is provided for quick reference and repeatable setting when working with the same nominal diameters. Is this a digital instrument? No, the MS908.656 is an analogue internal micrometer, combining mechanical reliability with a fine spindle for controlled readings. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a self‑centring three‑point measuring head and a 0.005 mm accuracy across a compact 50–63 mm range for reproducible blind‑bore inspections; order the instrument directly via Metav Werkzeuge or consult the specialists for application advice. Three‑point internal micrometer MS908.659 — Metav IndustryLine, self‑centring, 50–63 mm The Three‑point internal micrometer is a precision instrument designed for accurate measurement of blind bores and other internal diameters within the 50–63 mm range, combining a self‑centring three‑point head with robust analogue mechanics for repeatable results. Self‑centring three‑point measuring head Range 50–63 mm Accuracy 0.005 mm Carbide measuring faces Reproducible internal measurements through self‑centring design The instrument’s self‑centring three‑point measuring head converts small operator variations into consistent contact across the bore, which reduces eccentricity and minimises measurement scatter. With a declared accuracy of 0.005 mm and an analogue readout, this tool offers a clear, verifiable performance baseline that supports process control and reduces rework in production environments. The three‑point geometry is particularly effective on short to medium blind bores, where central alignment is critical to obtain reliable diameter values. Built for workshop use: durable faces and compact handling Equipped with carbide measuring faces, the device resists wear from regular contact with machined surfaces and maintains form integrity during frequent use. The compact overall length of 114 mm and a setting ring of 62 support comfortable handling in workshop and inspection‑bench situations, enabling efficient measurement cycles without sacrificing stiffness. As an analogue instrument, it delivers straightforward operation and low maintenance while providing the tactile feedback many technicians prefer for repeat measurements. Practical benefits for quality assurance and inspection routines Integrating this internal micrometer into quality checks provides a direct improvement to inspection throughput and measurement consistency. The tool is explicitly suitable for blind‑bore applications and mechanical assembly checks, offering a reliable technical solution where calipers or telescoping gauges may be less repeatable. The combination of a robust three‑point head and carbide contact faces translates into fewer measurement-related interruptions and a steadier conformity assessment across batches. Contact Metav Werkzeuge in Emmerich for tailored advice on application and availability of the MS908.659 three‑point internal micrometer Technical data Article number: MS908.659 Product: Three‑point internal micrometer Manufacturer: Metav IndustryLine Numbers / Core technical data Measuring range: 50–63 mm Minimum range: 50 mm Maximum range: 63 mm Reading / resolution: 0.005 mm Accuracy: 0.005 mm Length: 114 mm Setting ring: 62 Special features / Designs Self‑centring three‑point head Carbide (hard‑metal) measuring faces Analogue mechanical operation Suitable for blind bores FAQ What degree of accuracy can be expected from this three‑point internal micrometer? The MS908.659 from Metav IndustryLine delivers an accuracy of 0.005 mm with a 0.005 mm reading increment, suitable for precise workshop inspection tasks. Is this instrument suitable for blind‑bore measurement only? While optimised for blind bores, the three‑point internal micrometer is also applicable to other internal diameter checks where central alignment and repeatability are required. How does the self‑centring feature improve measurement results? The self‑centring three‑point head ensures even contact around the circumference, reducing eccentricity and enabling more reproducible diameter readings during routine inspections. What maintenance is recommended to retain measurement reliability? Regular cleaning of the carbide faces and periodic verification against a calibrated ring gauge will preserve the instrument’s performance; the analogue mechanics favour simple, on‑site care. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Benefit from the self-centring design, carbide measuring faces and ±0.005 mm accuracy to secure reproducible internal measurements in compact assemblies; order the three-point internal micrometer directly via Metav Werkzeuge or consult our specialists for technical guidance. Three-point internal micrometer MS908.660 — self-centring, 62–75 mm range A compact, analogue three-point internal micrometer designed for precise internal diameter checks in confined bores and fine-mechanical work. Self-centring three-point mechanism Measuring range 62–75 mm High accuracy ±0.005 mm Carbide measuring faces, analogue Precision where access is restricted The three-point internal micrometer is engineered for accurate measurements in confined spaces. Its self-centring mechanism ensures the measuring anvils align centrally within a bore, reducing operator-induced eccentricity and improving repeatability. With a readout resolution of 0.005 mm and a verified accuracy of ±0.005 mm, the instrument provides a reliable basis for quality control tasks where small deviations matter. The compact profile and 114 mm body length make this instrument particularly suitable for short, deep bores and components that cannot be accessed with larger gauges, offering precision without the need for complex fixturing. Durable construction for consistent results Built with carbide measuring faces, the instrument resists wear and maintains a stable contact geometry over extended use, which preserves measurement integrity in production environments. The analogue mechanism is robust and free of electronics, making it uncomplicated to operate in workshop conditions where durability is paramount. The combination of hardened contact surfaces and mechanical simplicity translates into low maintenance and consistent performance during repetitive checking routines, supporting efficient inspection workflows on the shop floor. Practical handling and typical applications Designed for ease of use in inspection and assembly, the instrument delivers fast, reliable readings for internal diameters between 62 and 75 mm. Its three-point contact is particularly effective for detecting form deviations and average bore sizes without additional adapters. Typical applications include component verification in machining, maintenance checks on housings and bearings, and quality assurance in small-batch production. The analogue format permits immediate interpretation of results, while the instrument’s geometry supports measurements that would be difficult with external gauges or callipers. Contact Metav Werkzeuge today for tailored advice and to arrange supply of the Metav IndustryLine three-point internal micrometer MS908.660 via Metav Werkzeuge GmbH; technical consultants are available at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: MS908.660 Brand: Metav IndustryLine Type: Analogue three-point internal micrometer Measuring range: 62–75 mm Readout: 0.005 mm Accuracy: ±0.005 mm Body length: 114 mm Self-centring mechanism Carbide measuring faces Suitable for blind-hole measurement Analogue (mechanical) operation FAQ How accurate is the three-point internal micrometer for routine inspection? The MS908.660 delivers an accuracy of ±0.005 mm, making it suitable for routine precision checks and quality control where sub-hundredth-millimetre repeatability is required. Can the instrument be used in blind or recess bores? Yes, the design is intended for confined and blind-hole measurements; the three-point contact provides reliable central alignment inside such bores. What maintenance is required to preserve measurement accuracy? Regular cleaning of contact surfaces and occasional verification on a calibrated reference ring are recommended to maintain the micrometer’s performance; the carbide measuring faces reduce wear and extend intervals between checks. Is the readout mechanical or electronic? This is an analogue instrument with a mechanical readout at 0.005 mm resolution, favouring robustness in workshop settings without relying on electronics. Which environments and applications suit this instrument best? The three-point internal micrometer is ideal for machine shops, maintenance workshops and inspection benches where compact, repeatable internal measurements are needed across small to medium-sized components. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com