HSS-E Spiralbohrer DIN 338 – Typ N, kurz, Co 5%, 135° Kreuzanschliff

Twist Drill Type N — 4.5 mm, 135° point angle, short execution, 5% cobalt-alloyed, HSS‑E, DIN 338 The Twist Drill Type N is a short HSS‑E metalworking bit designed for stable, precise drilling in hard materials with a 135° Point Angle and a fully ground shank for high concentricity. Short Twist Drill 4.5 mm for precise metalwork 135° Point Angle for hard materials like stainless steel 5% cobalt-alloyed HSS‑E for higher heat resistance Fully ground shank for excellent concentricity and finish Conforms to DIN 338 for short Twist Drills Designed for precision in metalworking and stable drilling Short design delivers a tangible benefit: reduced overhang means less deflection and improved accuracy when working with tough materials. The compact geometry of this short Twist Drill supports higher rigidity, so holes remain rounder and positional tolerances are easier to achieve. This is particularly relevant when machining alloyed or unalloyed Steel, Cast Iron and other Metals where tool chatter or bending would otherwise impair results. The result is a reliable Tool that helps maintain Process stability in both bench and machine applications. Robust Material and geometry for demanding applications Manufactured from HSS‑E with 5% cobalt-alloyed composition, the bit resists softening under elevated temperatures and keeps cutting edges sharper for longer life. The 135° Point Angle reduces entry forces on hard materials and improves centring on tougher Surfaces such as Stainless Steel. Being a Type N normal spiral, the geometry balances chip evacuation and edge strength—explainable: HSS‑E adds hot hardness, cobalt increases wear resistance; together they extend tool life under intermittent or high-load drilling. Machine compatibility and standards for reproducible results Designed according to DIN 338 for short Twist Drills, this Tool fits standard chuck systems and is intended for use in a drilling machine or hand drilling Machine where increased stiffness is required. The fully ground Shank ensures superior concentricity and runout characteristics, which supports precision fixtures and measured machining. For operators, this means fewer rejections and easier post-process handling when producing repeatable holes in metal components. Practical guidance, target users and safe operation Workshop professionals, maintenance technicians and toolroom users benefit most from this short Twist Drill due to its stability and suitability for harder metals. Use moderate cutting speeds, appropriate coolant for metalworking, and firm clamping to exploit the Drill’s advantages; avoid excessive overhang despite the short form. The fully ground flute geometry is explained by its manufacturing: grinding produces very sharp cutting edges and high Roundness, but requires careful handling to avoid brittle fractures—especially at very small diameters or under unsupported conditions. Strong recommendation: choose the MetavCUT Twist Drill Type N for precise metal drilling — for personalised technical advice contact METAV Werkzeuge; Email: info@metav-werkzeuge.com; Phone: +49 2822 7131930; WhatsApp: +49 170 2837271 Technical Data Designation: Twist Drill Marke: MetavCUT SKU: 47045-FDA Diameter: 4.5 mm Total Length: 80 mm Spiral Length: 47 mm Point Angle: 135° Typ: Type N Execution: short Material: HSS‑E Colour / Alloy: 5% cobalt-alloyed Shaft Finish: fully ground For Drilling Machine: Drilling Machine Application: Drills for metal Model Series: Standard Line Norm: DIN 338 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the best use for the Twist Drill Type N from MetavCUT? The MetavCUT Twist Drill Type N is primarily intended for drilling Metal; it excels in machining high-strength and alloyed steels thanks to its short design, which increases stability and reduces bending during operation. Can the MetavCUT Twist Drill Type N be used with a hand drilling machine? Yes, the MetavCUT Twist Drill Type N can be used in a hand drilling Machine, but optimal results are achieved with a well-secured workpiece and steady feed to minimise stress on the short, fully ground flute geometry. For what is a Twist Drill used? A Twist Drill is mainly applied when working on high‑strength materials and large diameters; its form is easy to regrind and withstands higher loads while remaining suitable for precision metal drilling. Which three drill types exist? The three main drill types are Metal drills, Wood drills and Stone/Concrete drills; the MetavCUT Twist Drill Type N belongs to the Metal drill category. Why are Twist Drills pointed? Pointing the Twist Drill reduces the secondary cutting edge at the tip, which lowers friction and the required feed forces while improving centring of the Drill in the Workpiece. Can a Twist Drill be used to drill wood? A Metal drill such as the MetavCUT Twist Drill Type N can be used in Wood, but guidance and hole finish are inferior compared with dedicated Wood drills; however, Metal drills are easier to regrind and have less self‑feeding tendency. At which drilling depths is the Twist Drill most used? A drilling operation into solid material is typically performed with a Twist Drill; for diameters up to 20 mm and drilling depths up to 100 mm, the Twist Drill is the most commonly used tool.

Spiralbohrer kurz, HSS‑E, 4,6 mm, 135°, Typ N, 5% kobaltlegiert, geschliffen, DIN 338, MetavCUT Der Spiralbohrer ist ein kurzer HSS‑E‑Bohrer für präzise Metallbohrungen in stationären und handgeführten Maschinen. Kurzbauform für höhere Stabilität beim Bohren HSS‑E 5% Kobaltlegierung für bessere Wärmebeständigkeit 135° Spitzenwinkel optimiert für harte Werkstoffe Geschliffen für hohe Rundlaufgenauigkeit und saubere Bohrlöcher DIN 338 Typ N für professionelle Metallbearbeitung Präzision und Stabilität durch kurze Bauform und HSS‑E Die kurze Ausführung dieses Kurzspiralbohrers reduziert die Auskraglänge und minimiert damit Vibrationen sowie Verbiegen, was zu präziseren Bohrbildern führt. Durch das Material HSS‑E mit einer 5% Kobaltlegierung wird die Wärmebeständigkeit erhöht und die Standzeit bei höheren Schnitttemperaturen verlängert. Die Kombination aus Kurzbauform und legiertem Schnellarbeitsstahl macht das Werkzeug besonders geeignet für anspruchsvolle Metallarbeiten, bei denen es auf Maßhaltigkeit und Wirtschaftlichkeit ankommt. Geeignete Anwendungen und Materialkompatibilität Der Bohrer eignet sich im Standard‑Bereich für allgemeine Werkstattarbeiten, Montage und DIY‑Projekte sowie für das Bohren in legiertem und unlegiertem Stahl, Gusseisen, Nichteisenmetallen und Kunststoffen. Für handgeführte Geräte wie die Handbohrmaschine bietet die robuste Kurzbauform besseren Halt und weniger Wandern beim Anbohren. Bei hoher Maßgenauigkeit empfiehlt sich ein vorheriges Zentrieren, um die Bohrlage weiter zu stabilisieren. Schleifverfahren, Geometrie und Wirkung auf das Bohrbild Die geschliffene Herstellung sorgt für sehr scharfe Schneiden und eine ausgezeichnete Rundlaufgenauigkeit, was saubere Bohrlochoberflächen und enge Toleranzen ermöglicht. Im Vergleich zu walzgeformten Bohrern erzeugt der geschliffene Bohrer meist präzisere Ergebnisse, zeigt jedoch eine höhere Sprödigkeit; deshalb profitieren Anwender von kontrollierter Vorschubbewegung und Kühlschmierstoff bei stationären Einsätzen. Der Typ N mit Normalspirale bietet dabei ein ausgewogenes Spanabfuhrverhalten für mittlere Bohrtiefen. Sicherheit, Pflege und praktische Hinweise für den Einsatz Für eine lange Lebensdauer sollten moderate Schnittbedingungen und geeignete Kühlschmierstoffe verwendet werden. Tiefe Bohrungen über das Fünffache des Durchmessers hinaus werden allgemein nicht empfohlen, da die Spanabfuhr erschwert wird. Die gemessene Spirallänge von 47 mm und die Gesamtlänge von 80 mm bieten eine praktikable Kombination aus Einstecktiefe und Stabilität. Bei Verschleiß oder Abstumpfung ist ein rechtzeitiger Wechsel der Schneide empfehlenswert, um Materialschäden zu vermeiden. Die Empfehlung: Setzen Sie auf die MetavCUT Standard Line HSS‑E Kurzspiralbohrer für präzise Metallbohrungen und kontaktieren Sie METAV Werkzeuge für individuelle Beratung unter info@metav-werkzeuge.com oder Telefon +49 2822 7131930 Bezeichnung: Spiralbohrer Marke: MetavCUT SKU: 47046-FDA Durchmesser: 4,6 mm Spitzenwinkel: 135° Typ: Typ N Farbe: 5% kobaltlegiert Ausführung: kurz Material: HSS-E Schaft Ausführung: geschliffen Norm: DIN 338 Gesamtlänge: 80 mm Spirallänge: 47 mm Für Bohrmaschine: Handbohrmaschine Modellserie: Standard Line Verpackungseinheit: 10 Preis Netto: 2.62 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Für welche Materialien ist der Spiralbohrer von MetavCUT geeignet? Der Spiralbohrer von MetavCUT wurde für die Bearbeitung von legiertem und unlegiertem Stahl, Gusseisen, Nichteisenmetallen und Kunststoffen entwickelt und liefert bei diesen Werkstoffen eine gute Standzeit und saubere Bohrbilder. Kann der Spiralbohrer in einer Handbohrmaschine verwendet werden? Ja, der Spiralbohrer aus der MetavCUT Standard Line eignet sich für den Einsatz in Handbohrmaschinen, wobei die kurze Ausführung die Stabilität verbessert und das Wandern beim Anbohren reduziert. Warum ist der Bohrer geschliffen und was bedeutet das für den Anwender? Die geschliffene Geometrie beim MetavCUT Spiralbohrer sorgt für scharfe Kanten und hohe Rundlaufgenauigkeit, was saubere Bohrlöcher ermöglicht; Anwender sollten jedoch mit Kühlschmierstoff arbeiten und bei stationären Maschinen besonders auf kontrollierten Vorschub achten. Welchen Vorteil bietet der 135° Spitzenwinkel beim MetavCUT Spiralbohrer? Der 135° Spitzenwinkel des MetavCUT Spiralbohrers erleichtert das Anbohren in härteren Werkstoffen und reduziert das Quietschen sowie das Aufbrechen der Bohrlochkante, wodurch die Prozesssicherheit steigt. Sind Sie sich nicht sicher, ob dieses Werkzeug Ihre Anforderungen erfüllt? Oder benötigen Sie ergänzende technische Daten? Kein Problem – wir stehen Ihnen gerne zur Verfügung. 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp: +49 170 2837271 {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#47046-FDA","sku":"47046-FDA","mpn":"47046-FDA","name":"Spiralbohrer 47046-FDA","description":"Kurzspiralbohrer HSS-E 5% Kobaltlegierung, Durchmesser 4,6 mm, Spitzenwinkel 135°, Typ N, geschliffen, DIN 338; Geeignet für präzise Metallbohrungen in legiertem und unlegiertem Stahl, Gusseisen, Nichteisenmetallen und Kunststoffen; robuste Kurzbauform für bessere Stabilität und reduzierte Vibrationen.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741b/logo-metav-1200-1200.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741e/logo-metav-1200-900.png"],"additionalProperty":[{"@type":"PropertyValue","name":"Bezeichnung","value":"Spiralbohrer"},{"@type":"PropertyValue","name":"Marke","value":"MetavCUT"},{"@type":"PropertyValue","name":"Durchmesser","value":"4,6 mm"},{"@type":"PropertyValue","name":"Spitzenwinkel","value":"135°"},{"@type":"PropertyValue","name":"Typ","value":"Typ N"},{"@type":"PropertyValue","name":"Farbe","value":"5% kobaltlegiert"},{"@type":"PropertyValue","name":"Ausführung","value":"kurz"},{"@type":"PropertyValue","name":"Norm","value":"DIN 338"},{"@type":"PropertyValue","name":"Material","value":"HSS-E"},{"@type":"PropertyValue","name":"Schaft Ausführung","value":"geschliffen"},{"@type":"PropertyValue","name":"Gesamtlänge","value":"80 mm"},{"@type":"PropertyValue","name":"Spirallänge","value":"47 mm"},{"@type":"PropertyValue","name":"Für Bohrmaschine","value":"Handbohrmaschine"},{"@type":"PropertyValue","name":"Modellserie","value":"Standard Line"},{"@type":"PropertyValue","name":"Verpackungseinheit","value":"10"},{"@type":"PropertyValue","name":"Preis Netto","value":"2.62"},{"@type":"PropertyValue","name":"Hersteller","value":"Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"Für welche Materialien ist der Spiralbohrer von MetavCUT geeignet?","acceptedAnswer":{"@type":"Answer","text":"Der Spiralbohrer von MetavCUT ist für legierten und unlegierten Stahl, Gusseisen, Nichteisenmetalle und Kunststoffe geeignet und liefert bei diesen Werkstoffen gute Standzeiten sowie saubere Bohrbilder."}},{"@type":"Question","name":"Kann der Spiralbohrer in einer Handbohrmaschine verwendet werden?","acceptedAnswer":{"@type":"Answer","text":"Ja, der Spiralbohrer von MetavCUT in kurzer Ausführung eignet sich für Handbohrmaschinen; die kürzere Auskraglänge verbessert die Stabilität und reduziert das Wandern beim Anbohren."}},{"@type":"Question","name":"Warum ist der Spiralbohrer geschliffen und was bedeutet das für den Anwender?","acceptedAnswer":{"@type":"Answer","text":"Die geschliffene Geometrie sorgt für sehr scharfe Schneiden und hohe Rundlaufgenauigkeit, was präzise Bohrlochoberflächen ermöglicht; Anwender sollten bei stationären Einsätzen Kühlschmierstoff verwenden und kontrollierten Vorschub sicherstellen."}},{"@type":"Question","name":"Welchen Vorteil bietet der 135° Spitzenwinkel beim MetavCUT Spiralbohrer?","acceptedAnswer":{"@type":"Answer","text":"Der 135° Spitzenwinkel erleichtert das Anbohren in härteren Werkstoffen wie Edelstahl, reduziert Quietschen und Aufbrechen der Bohrlochkante und erhöht dadurch die Prozesssicherheit."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/product/47046-FDA","dateModified":"2026-05-04T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Kurzspiralbohrer DIN 338"},{"@type":"Thing","name":"HSS-E 5% Kobaltlegierung"},{"@type":"Thing","name":"Bohrer für Metall"}],"mentions":[{"@type":"Thing","name":"Handbohrmaschine empfohlen"},{"@type":"Thing","name":"Kühlschmierstoff bei stationärem Einsatz"},{"@type":"Thing","name":"Typ N Normalspirale"}]}]}

Twist Drill Type N — 4.7 mm, 135° tip, short HSS‑E (5% cobalt-alloyed, DIN 338) The Twist Drill Type N is a short, fully ground HSS‑E drill bit designed for precision metalworking on Drilling Machines. Short design for increased stability and accuracy 4.7 mm diameter for fine metal drilling 135° tip angle optimised for hard materials HSS‑E with 5% cobalt-alloyed for wear resistance Fully ground shank for excellent concentricity Enhanced wear resistance for demanding metalwork The short Twist Drill is manufactured from HSS‑E with 5% cobalt‑alloyed composition, which increases red‑hardness and wear resistance when machining stainless steels and other hard alloys. The 135° tip angle reduces chipping and helps maintain the cutting edge during slow, precise feeds, so the cutter stays effective longer under stress. This results in reliable hole quality and extended tool life even in tougher materials. Short geometry for superior stability and precision A reduced overhang and a flute length of 47 mm combined with an overall length of 80 mm minimise bending and vibration during drilling. The short execution improves stiffness, which is particularly beneficial when working on small‑diameter holes or in setups with limited support. The fully ground shank ensures high concentricity in the chuck, translating into cleaner bores and less runout when used in stationary or portable Drilling Machines. Practical application and recommended use cases Compliant with DIN 338 and produced in the Standard Line, this Type N Twist Drill is intended primarily for drilling metal, including alloyed and unalloyed steels, cast iron, non‑ferrous metals and selected plastics. Its geometry and material make it suitable for workshop and industrial environments where precision matters. Operators seeking a drill bit that combines serviceable sharpness with simple reconditioning will find this design easy to re‑grind and maintain. We recommend choosing the MetavCUT Twist Drill Type N for precise, durable metal drilling — for technical questions or tailored advice METAV Werkzeuge provides expert support via info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical specifications Designation: Twist Drill Brand: MetavCUT SKU: 47047-FDA Type: Type N Diameter: 4.7 mm Tip Angle: 135° Material: HSS‑E Colour/Alloy: 5% cobalt-alloyed Execution: short Spiral (Flute) Length: 47 mm Overall Length: 80 mm Shank Finish: fully ground For Use In: Drilling Machine Application: Drills for metal Model Series: Standard Line Standard: DIN 338 Packaging Unit: 10 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill (MetavCUT, Type N) used for? The MetavCUT Twist Drill Type N is primarily employed for machining high‑strength materials and larger diameters; its geometry is easy to regrind and it withstands higher loads, making it suitable for demanding metalworking tasks. Which three drill types exist? The main categories are metal drills, wood drills and stone/concrete drills; the MetavCUT Twist Drill belongs to the metal drill category and is tailored for metalworking. Why are Twist Drills point‑split? Point splitting reduces the web thickness at the tip, which lowers friction and therefore requires less feed force; this also improves centring of the drill in the workpiece. Can a metal Twist Drill be used for wood? A metal drill can be used in wood, but it gives less precise guidance and a rougher finish; on the plus side, such drills are easier to regrind and have lower self‑feeding tendency. For what drilling depths is the Twist Drill most used? Solid drilling is commonly performed with a Twist Drill; for diameters up to 20 mm and drilling depths up to 100 mm, the Twist Drill is the most frequently used tool. Is HSS or HSSE better? The general belief that HSSE is always superior to HSS is incorrect; you should evaluate whether the specific working conditions justify the higher cost of HSSE before choosing.

Twist Drill — Type N, 4.8 mm, 135° tip, Short, 5% cobalt-alloyed, HSS‑E, DIN 338 (MetavCUT) The Twist Drill Type N is a short configuration drill for precision metalworking, engineered for handheld drilling machines and demanding machining of harder materials. Short design for high drilling stability 4.8 mm Diameter for precise metal holes 135° Tip angle for harder materials 5% cobalt-alloyed HSS‑E for heat resistance Longer life and heat resistance through alloyed HSS Built from HSS‑E with a 5% cobalt alloy, this short Twist Drill offers improved hot hardness and wear resistance compared with standard high-speed steels. The cobalt enrichment helps maintain cutting edge integrity at elevated cutting temperatures, which is particularly beneficial when drilling stainless steel or other tough metals. As a result, users gain longer tool life and fewer tool changes during longer runs. Stable short design for precise, vibration‑reduced drilling The shortened overall length reduces cantilever and increases rigidity, making the tool less prone to bending and chatter. With a short configuration and fully ground flute geometry, this Twist Drill provides a precise cut and excellent concentricity even in handheld or portable setups. For workshop tasks that demand accurate hole placement, the reduced overhang translates directly into cleaner holes and improved repeatability. Geometry optimised for harder materials and clean entry A 135° tip angle is chosen to reduce wandering on hard surfaces and to lower the initial penetration force, which improves centring on stainless and alloyed steels. The ground geometry (HSS‑G style) yields sharp cutting lips and a defined chisel edge, producing clean bores with good surface quality. For operators who require predictable performance when starting a hole in steel, this geometry is a practical advantage. Suited uses and target users This Twist Drill in the Standard Line series is intended primarily for metalworkers, maintenance technicians and industrial workshops that perform drilling in alloyed and unalloyed steel, cast iron, non‑ferrous metals and selected plastics. The tool is a robust choice for general metal drilling tasks on portable drilling machines and small machine tools where stiffness and hole quality matter more than extreme reach. Handling, sharpening and recommended operating practice Because the flute geometry is fully ground, the drill produces fine chips and precise holes but can be more brittle than rolled types; therefore, the tool benefits from controlled feeds and adequate cooling. For best results use cutting fluid when drilling harder alloys and avoid excessive feed rates on small diameters. If regrinding is required, the ground geometry allows restoration of sharp cutting edges, but care must be taken to preserve the 135° tip form for consistent performance. MetavCUT’s Twist Drill is recommended for precise metalworking tasks — for tailored technical advice or to confirm suitability for your applications contact METAV Werkzeuge: info@metav-werkzeuge.com | Tel +49 2822 7131930 | WhatsApp +49 170 2837271 Twist Drill Marke: MetavCUT SKU: 47048-FDA Diameter: 4.8 mm Tip Angle: 135° Execution: Short Material: HSS‑E Spiral Length: 52 mm Overall Length: 86 mm Type: Type N Shank Execution: Fully ground Colour: 5% cobalt-alloyed Norm: DIN 338 For Drill Machine: Drilling Machine Model Series: Standard Line Packaging Unit: 10 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill from MetavCUT mainly used for? The MetavCUT Twist Drill is primarily used for drilling high‑strength materials and larger diameter metal holes; its short design and ground geometry make it suitable for precision work in alloyed and unalloyed steel, cast iron, non‑ferrous metals and plastics, while offering easier regrinding and good resistance to breakage on small diameters. Which three drill types exist and how does the MetavCUT Twist Drill fit in? Common categories are metal drills, wood drills and masonry/concrete drills; the MetavCUT Twist Drill belongs to the metal drill category and is optimised for metalworking tasks with features like HSS‑E material and a Type N spiral suited to machining metals. Why are Twist Drills point‑sharpened? Point sharpening reduces the cross‑cut at the tip, lowering friction and cutting forces; by sharpening the tip the MetavCUT Twist Drill requires less feed force, centres better in the workpiece and delivers improved drilling behaviour across a range of metals. Can a metal Twist Drill be used to drill wood? A metal Twist Drill can be used in wood, but the MetavCUT Twist Drill will generally give less precise guidance and a rougher finish than a dedicated wood bit; however it is easier to resharpen and offers lower self‑feeding tendency compared with some specialised wood drills.

Spiralbohrer 4,9 mm – HSS‑E, 135°, Typ N, 5% kobaltlegiert, kurz, geschliffen, DIN 338 von MetavCUT Der Spiralbohrer 4,9 mm ist ein kurzer, geschliffener HSS‑E Bohrer nach DIN 338, konzipiert für präzise Metallbohrungen in handgeführten und stationären Anwendungen. Kurzformat für erhöhte Stabilität HSS‑E mit 5% Kobalt für zähe Werkstoffe 135° Spitzenwinkel für Edelstahl und gehärtete Stähle Geschliffener Schaft für hohe Rundlaufgenauigkeit Spirallänge 52 mm, Gesamtlänge 86 mm ideal für kurze Auskragung Höhere Präzision und geringere Verformung für Metallbohrungen Der kurze Bauform‑Bohrer bietet eine deutlich reduzierte Auskraglänge, wodurch Vibration und Durchbiegung minimiert werden. Das Resultat ist eine verbesserte Maßhaltigkeit der Bohrung und ein sicherer Spanfluss bei gängigen Metallarbeiten. Die Kombination aus HSS‑E und 5% Kobalt erhöht die Warmhärte, was besonders bei höheren Schnittgeschwindigkeiten in Stahl und Edelstahl von Vorteil ist. Die Spirallänge 52 mm und die Gesamtlänge 86 mm sorgen für kompakte Handhabung, speziell bei Werkstücken mit begrenzter Zugänglichkeit. Materialqualität und Fertigungsverfahren erklärt Der geschliffene Schaft (CNC‑Schliff) erzeugt eine sehr scharfe Schneidkante und exzellenten Rundlauf, was saubere Bohrbilder in Metall ermöglicht. Die Ausführung nach DIN 338 steht für kurze Spiralbohrer mit Zylinderschaft und definiert Toleranzen sowie Geometrie. Im Vergleich zu gewalzten Bohrern liefert die geschliffene Variante höhere Präzision, benötigt allerdings angepasste Kühlschmierstoffe und schonende Vorschübe, um das Bruchrisiko zu minimieren. Einsatzbereich, Nutzerprofil und Praxistipps für beste Ergebnisse Mit einem Durchmesser von 4,9 mm fällt der Bohrer in den Standard‑Bereich, ideal für Werkstatt, Montage und DIY‑Projekte. Er eignet sich für dünne bis mittlere Bleche, Profile und allgemeine Metallbearbeitung mit Handbohrmaschine oder stationärer Säulenbohrmaschine. Für besonders präzise Passungen empfiehlt sich vorbohren oder Anpunkten zur Vermeidung von Wandern. Tiefe Bohrungen über das fünffache des Durchmessers sollten vermieden werden, da sonst Spanabfuhr und Kühlung beeinträchtigt werden. Handhabungsempfehlungen und Gründe für die Wahl dieser Ausführung Für langlebige Schneiden ist die Kombination aus moderater Schnittgeschwindigkeit, kontinuierlicher Kühlung und gleichmäßigem Vorschub entscheidend. Die 135° Spitzengeometrie erleichtert das Anbohren harter Werkstoffe und reduziert Ausläufer beim Eindringen. Die kurze, geschliffene Bauart bietet Nutzern mehr Kontrolle bei der Führung und liefert wiederholbar präzise Bohrungen. Wer auf Zuverlässigkeit und reproduzierbare Ergebnisse setzt, profitiert von der Standard Line Ausführung dieser Serie. Greifen Sie zur MetavCUT Standard Line, wenn präzise Metallbohrungen gefordert sind — bei Unsicherheit berät METAV Werkzeuge gern persönlich unter info@metav-werkzeuge.com oder telefonisch +49 2822 7131930 Bezeichnung: Spiralbohrer 4,9 mm kurz, geschliffen Marke: MetavCUT SKU: 47049-FDA Durchmesser: 4,9 mm Spirallänge: 52 mm Gesamtlänge: 86 mm Material: HSS‑E Farbe: 5% kobaltlegiert Typ: Typ N (Normalspirale) Spitzenwinkel: 135° Ausführung: kurz, geschliffen Norm: DIN 338 Für Bohrmaschine: Handbohrmaschine, stationäre Maschinen geeignet Schaft Ausführung: geschliffen Modellserie: Standard Line Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Ist der Spiralbohrer 4,9 mm von MetavCUT für Edelstahl geeignet? Der Spiralbohrer 4,9 mm von MetavCUT in HSS‑E Ausführung mit 5% Kobalt und 135° Spitzenwinkel ist speziell für harte Werkstoffe wie Edelstahl geeignet; empfohlen werden reduzierte Schnittgeschwindigkeiten und kontinuierliche Kühlung zur Verlängerung der Lebensdauer. Kann der Spiralbohrer 4,9 mm mit einer Handbohrmaschine genutzt werden? Ja, der Spiralbohrer 4,9 mm (MetavCUT Standard Line) ist für Handbohrmaschine und stationäre Maschinen ausgelegt; aufgrund der kurzen Auskragung bietet er besonders bei handgeführten Geräten erhöhte Stabilität. Wie verhindere ich beim Spiralbohrer 4,9 mm Bruch und Verschleiß? Bei dem MetavCUT Spiralbohrer 4,9 mm senken geeignete Kühlmittel, angepasste Vorschubgeschwindigkeit und das Anpunkten vor dem Bohren das Bruchrisiko; geschliffene Werkzeuge erfordern kontrollierte Bedingungen, um Spitzenversprödung zu vermeiden. Worin unterscheidet sich der geschliffene Spiralbohrer 4,9 mm von gewalzten Bohrern? Der geschliffene Spiralbohrer 4,9 mm von MetavCUT bietet schärfere Kanten und höhere Rundlaufgenauigkeit, wodurch sauberere Bohrlöcher in Metall erzielt werden; als Nachteil ist eine größere Empfindlichkeit gegen unsachgemäße Handhabung zu beachten. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#47049-FDA","sku":"47049-FDA","mpn":"47049-FDA","name":"Spiralbohrer 4,9 mm kurz geschliffen DIN 338","description":"Spiralbohrer 4,9 mm, HSS‑E mit 5% Kobalt, 135° Spitzenwinkel, Typ N, kurz, geschliffen; ideal für präzise Metallbohrungen in Werkstatt und Montage; Spirallänge 52 mm, Gesamtlänge 86 mm; geeignet für Handbohrmaschine und stationäre Maschinen.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741b/logo-metav-1200-1200.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741e/logo-metav-1200-900.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png"],"additionalProperty":[{"@type":"PropertyValue","name":"Durchmesser","value":"4,9 mm"},{"@type":"PropertyValue","name":"Material","value":"HSS‑E, 5% Kobaltlegiert"},{"@type":"PropertyValue","name":"Spitzenwinkel","value":"135°"},{"@type":"PropertyValue","name":"Typ","value":"Typ N (Normalspirale)"},{"@type":"PropertyValue","name":"Ausführung","value":"kurz, geschliffen"},{"@type":"PropertyValue","name":"Spirallänge","value":"52 mm"},{"@type":"PropertyValue","name":"Gesamtlänge","value":"86 mm"},{"@type":"PropertyValue","name":"Schaft Ausführung","value":"geschliffen"},{"@type":"PropertyValue","name":"Modellserie","value":"Standard Line"},{"@type":"PropertyValue","name":"Norm","value":"DIN 338"},{"@type":"PropertyValue","name":"Für Bohrmaschine","value":"Handbohrmaschine, stationäre Maschinen geeignet"},{"@type":"PropertyValue","name":"Eignung","value":"Legierter und unlegierter Stahl, Gusseisen, Nichteisenmetalle, Kunststoffe"},{"@type":"PropertyValue","name":"Hersteller","value":"MetavCUT"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"Ist der Spiralbohrer 4,9 mm von MetavCUT für Edelstahl geeignet?","acceptedAnswer":{"@type":"Answer","text":"Der Spiralbohrer 4,9 mm von MetavCUT ist in HSS‑E Ausführung mit 5% Kobalt und 135° Spitzenwinkel ausgelegt, daher besonders geeignet für Edelstahl; reduzierte Schnittgeschwindigkeit und kontinuierliche Kühlung verlängern die Lebensdauer."}},{"@type":"Question","name":"Kann der Spiralbohrer 4,9 mm mit einer Handbohrmaschine genutzt werden?","acceptedAnswer":{"@type":"Answer","text":"Der Spiralbohrer 4,9 mm von MetavCUT ist für Handbohrmaschine und stationäre Maschinen geeignet; die kurze Bauform reduziert Auskragung und erhöht die Stabilität bei handgeführten Anwendungen."}},{"@type":"Question","name":"Wie verhindere ich beim Spiralbohrer 4,9 mm Bruch und Verschleiß?","acceptedAnswer":{"@type":"Answer","text":"Beim Spiralbohrer 4,9 mm von MetavCUT senken geeignete Kühlmittel, angepasste Vorschubgeschwindigkeit und Anpunkten vor dem Bohren das Bruchrisiko; geschliffene Werkzeuge sollten kontrolliert und mit Kühlung betrieben werden."}},{"@type":"Question","name":"Worin unterscheidet sich der geschliffene Spiralbohrer 4,9 mm von gewalzten Bohrern?","acceptedAnswer":{"@type":"Answer","text":"Der geschliffene Spiralbohrer 4,9 mm von MetavCUT bietet schärfere Kanten und höhere Rundlaufgenauigkeit für saubere Bohrlöcher in Metall; gewalzte Bohrer sind hingegen oft zäher, aber weniger präzise."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/produkte/47049-FDA","dateModified":"2026-05-04T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Spiralbohrer Standard Line"},{"@type":"Thing","name":"Kurzbohrer nach DIN 338"},{"@type":"Thing","name":"Metallbearbeitung hoher Präzision"}],"mentions":[{"@type":"Thing","name":"HSS‑E mit 5% Kobalt"},{"@type":"Thing","name":"Geschliffener Schaft (CNC‑Schliff)"},{"@type":"Thing","name":"135° Spitzenwinkel für harte Werkstoffe"},{"@type":"Thing","name":"Typ N Normalspirale"}]}]}

Twist Drill Type N — short, Ø 4 mm, 135° tip angle, 5% cobalt-alloyed, HSS‑E, DIN 338, fully ground shank — MetavCUT The Twist Drill Type N is a short HSS‑E metalworking drill designed for Drilling Machines, offering improved stability and precise performance when machining hard and alloyed steels. Short design for increased stability 135° tip angle for harder materials 5% cobalt-alloyed for heat resistance Fully ground shank for high concentricity Conforms to DIN 338 for standardised dimensions Stable, precise drilling even in hard materials A short Twist Drill made of HSS‑E combines rigidity and wear resistance to reduce vibration and improve hole quality. The reduced overhang of the short execution limits bending and delivers consistent concentricity, which means cleaner holes and longer tool life when working with alloyed and unalloyed steel. The 135° tip angle is tuned to penetrate harder materials with less walking at the start, improving process reliability in demanding metalworking jobs. Material and geometry that add real value The use of 5% cobalt‑alloyed HSS‑E gives this drill enhanced red hardness and thermal stability, reducing wear at elevated cutting temperatures. A fully ground shaft and flute geometry ensure sharp cutting edges and excellent runout accuracy, which benefits precision assemblies and reaming-sensitive operations. For users who need tools that are easy to resharpen and that maintain edge geometry under load, this construction is a practical choice. Designed to match industrial standards and applications Manufactured to DIN 338, this short Twist Drill Type N is suited for standard metalworking set-ups on portable and stationary drilling equipment. The Type N spiral is the conventional choice for metal drilling, delivering controlled chip removal and a balance between cutting speed and surface finish. Typical applications include drilling in steel, cast iron, non-ferrous metals and many engineering plastics where a robust, general-purpose metal drill is required. Practical notes for users and support For drilling below 6 mm diameter, the short form factor reduces breakage risk and is especially useful when machining with minimal clamping or on smaller workpieces. If uncertain whether this Twist Drill Type N matches a specific machine or material condition, METAV Werkzeuge provides expert guidance and supplementary technical data to help select the right tool and operating parameters. Contact options are available for tailored advice and application support. Strong recommendation: Choose the MetavCUT Twist Drill Type N for reliable precision in metal machining — for application help or additional technical data contact METAV Werkzeuge by eMail: info@metav-werkzeuge.com, Phone: +49 2822 7131930 or WhatsApp: +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 47040-FDA Diameter: 4 mm Tip angle: 135° Type: Type N Material: HSS‑E (5% cobalt‑alloyed) Execution: short Spiral length: 43 mm Overall length: 75 mm Shank execution: fully ground Conforms to: DIN 338 Intended use: Drills for metal Model series: Standard Line For use in: Drilling Machine Packaging unit: 10 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ For what is a Twist Drill used? A Twist Drill Type N from MetavCUT is primarily applied when machining high‑strength materials and larger drill diameters; its geometry is easy to resharpen and it withstands higher loads, making it suitable for demanding metal drilling tasks and for materials where increased toughness and heat resistance are required. Which three drill types exist? Common categories are Metal drill (such as the MetavCUT Twist Drill Type N), Wood drill, and Masonry/Concrete drill; each group is optimised in geometry and material to perform best in its respective material class.

Spiralbohrer HSS‑E 5,1 mm, 135°, Typ N, 5% kobaltlegiert, kurz, geschliffen, DIN 338 — MetavCUT Standard Line Der Spiralbohrer kurz in HSS‑E mit 5,1 mm Durchmesser und 135° Spitzenwinkel eignet sich für präzise Metallbohrungen an Handbohrmaschinen und stationären Geräten. Präzise Bohrungen in Metall möglich Kurze Ausführung für hohe Stabilität 5% Kobaltlegierung für erhöhte Härte Geschliffene Schaftausführung, hohe Rundlaufgenauigkeit DIN 338 als Industriestandard Kompakte Bauweise sorgt für genauere Ergebnisse bei Metall Die kurze Ausführung reduziert das Auskragen des Bohrers deutlich und minimiert so Vibrationen und Verbiegen beim Bohren. Dadurch entsteht eine verbesserte Stabilität, die besonders bei anspruchsvollen Metallarbeiten zu saubereren Bohrlöchern und längerem Werkzeugleben führt. Anwender profitieren von geringerer Werkzeugabnutzung und konstanteren Ergebnissen bei wiederholten Bohrungen. Werkstoff und Legierung ermöglichen hohe Schneidleistung Der Einsatz von HSS‑E mit 5% Kobalt erhöht die Warmfestigkeit und die Verschleißbeständigkeit, was sich bei legierten Stählen und schwer zerspanbaren Werkstoffen auszahlt. Der 135° Spitzenwinkel reduziert die Anbohrkräfte in harten Materialien und sorgt für sauberes Einstechen. Für Anwender bedeutet das: weniger Nacharbeit und zuverlässige Bohrbildqualität bei mittleren bis hohen Anforderungen. Vielseitiger Einsatzbereich für Werkstatt und Montage Mit einem Durchmesser von 5,1 mm liegt der Bohrer im Standard‑Bereich, ideal für Alltagseinsätze in Werkstatt, Montage und für DIY‑Projekte. Die Ausführung Typ N ist für Metallbohrungen optimiert und funktioniert gut an einer Handbohrmaschine, solange vor Anbohren angepunktet und mit passender Kühlung gearbeitet wird. Diese Kombination macht das Werkzeug zur praktischen Lösung für dünne bis mittlere Bleche, Profile und Kunststoffe. Verarbeitungshinweise verlängern die Standzeit Die geschliffene Fertigung sorgt für sehr scharfe Schneidkanten und hohe Rundlaufgenauigkeit, erfordert jedoch angepasste Schnittparameter und Kühlung, um Bruchrisiken zu minimieren. Die angegebene Spirallänge 52 mm und Gesamtlänge 86 mm sind für die meisten stationären wie mobilen Anwendungen praktisch dimensioniert. Durch Kühlmittel und moderate Vorschubwerte lässt sich die Standzeit nachhaltig erhöhen. Mit dem MetavCUT Spiralbohrer HSS‑E in kurzer Ausführung treffen Sie eine gezielte Wahl für präzise Metallbohrungen — bei Bedarf unterstützt METAV Werkzeuge mit technischer Beratung unter info@metav-werkzeuge.com, Telefon +49 2822 7131930 oder WhatsApp +49 170 2837271 Bezeichnung: Spiralbohrer Marke: MetavCUT SKU: 47051-FDA Durchmesser: 5,1 mm Material: HSS‑E Kobaltanteil: 5% kobaltlegiert Typ: Typ N Ausführung: kurz Schaft Ausführung: geschliffen Spirallänge: 52 mm Gesamtlänge: 86 mm Spitzenwinkel: 135° Norm: DIN 338 Für Bohrmaschine: Handbohrmaschine Modellserie: Standard Line Verpackungseinheit: 10 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Für welche Materialien eignet sich der Spiralbohrer von MetavCUT Typ N? Der Spiralbohrer von MetavCUT in HSS‑E eignet sich für legierten und unlegierten Stahl, Gusseisen, Nichteisenmetalle sowie Kunststoffe und liefert bei korrekter Kühlung saubere Bohrbilder. Welche Vorteile bietet die kurze Ausführung des Spiralbohrers von MetavCUT? Die kurze Ausführung des Spiralbohrers erhöht die Führungssicherheit und reduziert Vibrationen, sodass präzisere Löcher entstehen und die Standzeit des Werkzeugs steigt. Welche Schnittbedingungen sind für den MetavCUT Spiralbohrer zu empfehlen? Für den MetavCUT Spiralbohrer sind hohe Drehzahlen mit moderatem Vorschub vorteilhaft; bei härteren Werkstoffen empfiehlt sich Kühlschmierstoff und die Nutzung des 135° Spitzenwinkels für geringere Anbohrkräfte. Kann der Spiralbohrer von MetavCUT an einer Handbohrmaschine eingesetzt werden? Ja, der Spiralbohrer ist für den Einsatz an einer Handbohrmaschine ausgelegt; es sollte jedoch vorgepunktet und das Werkstück sicher gespannt werden, um Auslaufen und Bruch zu vermeiden. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#47051-FDA","sku":"47051-FDA","mpn":"47051-FDA","name":"Spiralbohrer 47051-FDA","description":"Spiralbohrer HSS‑E 5,1 mm, 135° Spitzenwinkel, Typ N, 5% Kobaltlegierung, kurz, geschliffen, DIN 338; geeignet für präzise Metallbohrungen in legierten und unlegierten Stählen, Gusseisen, Nichteisenmetallen und Kunststoffen; robuste Kurz-Ausführung für höhere Stabilität und reduzierte Vibrationen.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741b/logo-metav-1200-1200.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741e/logo-metav-1200-900.png"],"additionalProperty":[{"@type":"PropertyValue","name":"Bezeichnung","value":"Spiralbohrer"},{"@type":"PropertyValue","name":"Durchmesser","value":"5,1 mm"},{"@type":"PropertyValue","name":"Spitzenwinkel","value":"135°"},{"@type":"PropertyValue","name":"Typ","value":"Typ N"},{"@type":"PropertyValue","name":"Material","value":"HSS‑E"},{"@type":"PropertyValue","name":"Kobaltanteil","value":"5% kobaltlegiert"},{"@type":"PropertyValue","name":"Ausführung","value":"kurz"},{"@type":"PropertyValue","name":"Schaft Ausführung","value":"geschliffen"},{"@type":"PropertyValue","name":"Spirallänge","value":"52 mm"},{"@type":"PropertyValue","name":"Gesamtlänge","value":"86 mm"},{"@type":"PropertyValue","name":"Norm","value":"DIN 338"},{"@type":"PropertyValue","name":"Für Bohrmaschine","value":"Handbohrmaschine"},{"@type":"PropertyValue","name":"Modellserie","value":"Standard Line"},{"@type":"PropertyValue","name":"Verpackungseinheit","value":"10"},{"@type":"PropertyValue","name":"Hersteller","value":"MetavCUT"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"Für welche Materialien eignet sich der Spiralbohrer von MetavCUT Typ N?","acceptedAnswer":{"@type":"Answer","text":"Der Spiralbohrer MetavCUT Typ N in HSS‑E 5,1 mm eignet sich für legierten und unlegierten Stahl, Gusseisen, Nichteisenmetalle sowie Kunststoffe und liefert bei korrekter Kühlung saubere Bohrbilder."}},{"@type":"Question","name":"Welche Vorteile bietet die kurze Ausführung des Spiralbohrers von MetavCUT?","acceptedAnswer":{"@type":"Answer","text":"Die kurze Ausführung des Spiralbohrers MetavCUT reduziert Auskragung, minimiert Vibrationen und erhöht die Stabilität, was präzisere Löcher und längere Standzeiten ermöglicht."}},{"@type":"Question","name":"Welche Schnittbedingungen sind für den MetavCUT Spiralbohrer zu empfehlen?","acceptedAnswer":{"@type":"Answer","text":"Für den Spiralbohrer MetavCUT HSS‑E 5,1 mm sind hohe Drehzahlen mit moderatem Vorschub vorteilhaft; bei härteren Werkstoffen empfiehlt sich Kühlschmierstoff und Nutzung des 135° Spitzenwinkels für geringere Anbohrkräfte."}},{"@type":"Question","name":"Kann der Spiralbohrer von MetavCUT an einer Handbohrmaschine eingesetzt werden?","acceptedAnswer":{"@type":"Answer","text":"Ja, der Spiralbohrer MetavCUT Typ N eignet sich für Handbohrmaschinen, sofern vorgepunktet und das Werkstück sicher gespannt wird, um Auslaufen und Bruch zu vermeiden."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/produkt/47051-FDA","dateModified":"2026-05-04T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Spiralbohrer HSS‑E"},{"@type":"Thing","name":"Kurz Ausführung für präzise Metallbohrungen"},{"@type":"Thing","name":"Norm DIN 338"}],"mentions":[{"@type":"Thing","name":"5% Kobaltlegierung"},{"@type":"Thing","name":"Geschliffener Schaft"},{"@type":"Thing","name":"135° Spitzenwinkel"}]}]}

Twist Drill by MetavCUT — 5.2 mm, 135° Point Angle, Type N, 5% Cobalt-Alloyed, Short, DIN 338, HSS‑E The Twist Drill is a short Type N metal drill optimised for precise drilling in hard materials with Drilling Machine use. Short design for higher stability and precision 5% Cobalt-alloyed HSS‑E for increased heat resistance 135° Point Angle for cleaner entry in hard steels Fully ground shank for excellent concentricity Conforms to DIN 338 for short spiral drills Precision and stability for demanding metalwork Designed as a short Twist Drill, this tool reduces the exposed length beyond the chuck, which directly improves stability and minimises bending under load. For tasks that require exact hole placement and minimal run-out, the reduced overhang is decisive. The 5.2 mm diameter in combination with the short overall length yields consistently round holes, making the drill particularly suitable for precision operations in workshops and production environments. Material composition that endures heat and wear The Twist Drill is manufactured from HSS‑E (high-speed steel with 5% Cobalt), which enhances red hardness and wear resistance compared with standard HSS. This composition helps maintain cutting edge integrity at higher cutting temperatures and under intermittent heavy loads. The result is longer tool life when drilling alloyed and unalloyed steel, cast iron, non-ferrous metals and many plastics, while still allowing economical resharpening when required. Geometry engineered for hard materials and quick engagement With a 135° Point Angle, the cutter tip penetrates harder workpieces more smoothly and reduces the tendency to grab or chatter on initial contact. The drill’s Type N normal spiral geometry balances chip evacuation and cutting action for metalworking applications. Users benefit from a faster approach to the correct feed and from cleaner hole entry in tougher materials, which reduces the need for secondary deburring. Fully ground flutes for accuracy in industrial settings This Twist Drill features a fully ground design, where the flute geometry is produced by CNC grinding rather than roll-forming. Grinding delivers sharp cutting edges and high concentricity, producing precise holes with excellent surface finish. While ground drills can be slightly more brittle than roll-formed variants, their superior accuracy makes them the preferred choice for stationary drilling machines and demanding production processes. Suitable applications and recommended users Intended primarily as a metalworking tool, the Twist Drill is ideal for professional workshops, toolrooms and maintenance departments that operate Drilling Machines. It is particularly recommended where small-diameter precision holes are required in tougher steels and alloys. For users uncertain about fitment or machine compatibility, METAV Werkzeuge provides expert consultation to match tool, machine and process parameters. We strongly recommend the MetavCUT Twist Drill for precision metal drilling — for technical advice, machine compatibility checks or complementary data please contact METAV Werkzeuge: 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp +49 170 2837271 Designation: Twist Drill Marke: MetavCUT SKU: 47052-FDA Diameter: 5.2 mm Point Angle: 135° Type: Type N Execution: Short Colour / Alloy: 5% Cobalt-alloyed Material: HSS‑E Shaft Execution: Fully ground Spiral Length: 52 mm Overall Length: 86 mm For Drilling Machine: Drilling Machine Application: Drills for metal Norm: DIN 338 Model Series: Standard Line Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill used for and where does it perform best? The MetavCUT Twist Drill (Type N short) is used chiefly for machining high-strength materials and larger drill diameters; its short design makes it especially suitable for precise metal drilling where low deflection and high stability are required. Which three drill types are common in metalworking? Typical categories are metal drill, wood drill and stone/concrete drill, with the MetavCUT Twist Drill belonging to the metal drill family for drilling in metals. Why are Twist Drills sharpened at the tip? The sharpening reduces the web thickness at the tip of the Twist Drill, significantly lowering friction and thus required feed forces; this also improves self-centring and reduces the risk of wandering at the start of the hole. Can you use a Twist Drill for wood? A metal Twist Drill such as the MetavCUT Type N can be used in wood, but guidance is reduced and hole quality is often inferior compared with dedicated wood drills; however, metal drills are easier to resharpen and exhibit lower tendency to pull into the workpiece. For which drilling depths is the Twist Drill most commonly used? A through-hole in solid material is commonly executed with a Twist Drill; for diameters up to about 20 mm and drilling depths up to 100 mm the Twist Drill is the most frequently used tool. What is better, HSS or HSSE? The common assumption that HSSE steels are categorically superior to HSS is not universally correct; decide based on specific working conditions whether the additional cost of HSSE is justified, considering factors such as cutting speed, material and required tool life.

Twist Drill Type N — short, 5.7 mm, 135°, 5% cobalt-alloyed, HSS‑E, DIN 338, fully ground (MetavCUT Standard Line) The Twist Drill Type N short is a precision drill for metal, designed for Drilling Machine use and optimised for stable, accurate holes in hard materials. Short design for higher stability 5.7 mm diameter for standard metal holes 135° tip angle for hard materials HSS‑E with 5% cobalt alloy for toughness Fully ground shaft for precise bore quality Precision and material strength for demanding metalwork This paragraph explains why the Twist Drill Type N from MetavCUT suits hard-material applications: the combination of HSS‑E and 5% cobalt-alloyed composition increases heat resistance and Wear Resistance during high-speed drilling. Because the tool is made in a short execution, the Reduced Overhang improves rigidity and lowers the risk of bending, which yields cleaner bores and longer tool life. For users who require repeatable accuracy, these material choices translate directly into fewer rejects and less rework. Stability and cutting geometry that ease machining in steel Designed with a 135° tip angle and the classic Type N spiral geometry, this drill penetrates hard steels and alloys more effectively than steeper-point designs. The fully ground flute geometry (HSS‑G) produces sharp cutting edges and high Runout Accuracy, giving a better surface finish in the workpiece. Operators will benefit from reduced vibration and steadier feed, which is especially relevant when machining stainless steel or alloyed materials that demand longer tool life. When to choose a short twist drill and typical applications A short Twist Drill is recommended for operations where Precision and Stability matter: jig work, toolroom tasks and metal fabrication on handheld or bench Drilling Machines. Because of the reduced cantilever, the tool is particularly suited to drilling in rigid setups and hard materials; it is less appropriate where deep through-holes are required. If the task involves smaller hole diameters under high cutting speeds, the short design lowers breakage risk and supports reliable repeatability. Who benefits from this tool and what to expect in use Engineers, maintenance technicians and metalworkers who prioritise Hole Quality and tool durability will find the MetavCUT Standard Line short Twist Drill a pragmatic choice. Expect consistent centring thanks to the tip geometry, straightforward regrinding when needed, and compatibility with a range of ferrous and non‑ferrous metals. Use appropriate cooling and correct spindle speeds to exploit the HSS‑E alloy’s advantages and avoid premature wear. Strongly recommended: Choose the MetavCUT Standard Line Twist Drill for precision metalworking and consult METAV Werkzeuge for tailored advice — eMail: info@metav-werkzeuge.com / Phone: +49 2822 7131930 / WhatsApp: +49 170 2837271 Technical information Designation: Twist Drill (Short) Marke: MetavCUT SKU: 47057-FDA Diameter: 5.7 mm Tip angle: 135° Type: Type N Material: HSS‑E (High Speed Steel, cobalt alloy) Cobalt content: 5% cobalt-alloyed Execution: short Spiral length: 57 mm Overall length: 93 mm Shaft finish: fully ground Suitable for: Drilling Machine / Drills for metal Standard: DIN 338 Model series: Standard Line Application: Bohrer für Metall (Drills for metal) Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill Type N from MetavCUT used for? The Twist Drill Type N by MetavCUT is primarily applied to machining high-strength materials and larger drill diameters; its short design and robust alloy make it suitable for precise metalworking where stability is required. This form is easy to regrind and withstands higher loads. Which three drill types exist? Commonly, drill types are Metal Drill, Wood Drill and Stone/Concrete Drill; the MetavCUT Twist Drill belongs to the Metal Drill category and is optimised for ferrous and non‑ferrous metals. Why are Twist Drills tip-ground? Tip-grinding reduces the chisel edge at the point of the Twist Drill, significantly lowering friction so less feed force is needed and the tip centres more reliably in the workpiece. Can a Metal Drill be used in wood? A Metal Drill such as the MetavCUT Twist Drill can be used in Wood, but guidance is poorer and hole finish may be less clean; metal drills are easier to regrind and show less self-feeding compared with dedicated wood drills.

Twist Drill — Type N short HSS‑E 5.8 mm, 135°, 5% cobalt‑alloyed, fully ground, DIN 338 (MetavCUT) A Twist Drill Type N crafted for precise metal drilling with a short overall length for improved stability and performance. Short design for higher stability and precision 5% cobalt‑alloyed HSS‑E for increased heat resistance Fully ground shank for superior concentricity 135° tip angle for hard material penetration Conforms to DIN 338 for standardised quality Precision and strength for demanding metalwork The HSS‑E composition combined with a 5% cobalt‑alloyed matrix provides enhanced red hardness and wear resistance, making this short twist drill particularly suited for drilling stainless steel and other hard Alloys. The 135° tip angle reduces chipping on the cutting edge and shortens the initial entry phase, so holes are started cleaner with less walking. This design leads to consistent hole quality and fewer rejects when producing components that demand close tolerances. Stable short geometry for accurate results A reduced overhang is the main benefit of the short execution: it lowers bending moments and improves tool stability in handheld and bench drilling operations. The fully ground shaft and spiral geometry ensure excellent runout and roundness, which translates into noticeably better concentricity in the finished hole. For tasks where rigidity and repeatability matter, this configuration minimises vibration and helps maintain drill life under steady, cooled cutting conditions. Application focus and user advantages Engineered as a Type N twist drill, this tool excels in metalworking environments—from maintenance benches to production machinery. It is intended for use with a Drilling Machine or Hand Drill and performs well on alloyed and unalloyed steel, cast iron, non‑ferrous metals and plastics. The short length makes it ideal where access is limited or where a stable, precise bore is required. Users gain higher process reliability and improved surface finish with fewer burrs to deburr. Operating tips to extend lifetime and maintain precision For optimal performance with the MetavCUT short twist drill, use appropriate cutting speeds and continuous coolant or cutting fluid when machining steels and tougher alloys. Feed rates should be consistent and matched to diameter and material; overfeeding can induce breakage, underfeeding can cause rubbing and work hardening. Given the ground geometry, regrinding is feasible but should be performed by experienced personnel to preserve the exact tip angle and helix form. Why standards and manufacturing details matter Compliance with DIN 338 signals standardised dimensions and tolerances for short twist drills with cylindrical shank. Ground manufacturing (HSS‑G) produces sharp cutting edges and high running accuracy, which is especially beneficial for precision metal drilling. The MetavCUT approach combines these standards with material choices to give a balance between edge sharpness and toughness suitable for frequent metalworking tasks. Strongly recommended: choose the MetavCUT Twist Drill for precision metal drilling—contact METAV Werkzeuge for expert consultation and application support via email at info@metav-werkzeuge.com, by phone at +49 2822 7131930 or WhatsApp at +49 170 2837271 Technical information Designation: Twist Drill Brand: MetavCUT SKU: 47058-FDA Diameter: 5.8 mm Tip angle: 135° Type: Type N Material: HSS‑E Colour / Alloy: 5% cobalt‑alloyed Execution: short Shank execution: fully ground Spiral length: 57 mm Total length: 93 mm Application: Drills for metal For drilling machine: Drilling Machine / Hand Drill Model series: Standard Line Norm: DIN 338 Packaging unit: 10 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials is the Twist Drill from MetavCUT best suited for? The MetavCUT Twist Drill with its HSS‑E composition and 5% cobalt‑alloyed content is optimised for alloyed and unalloyed steel, cast iron, non‑ferrous metals and many hard plastics; the 135° tip angle helps when penetrating harder materials such as stainless steel. How should the MetavCUT Twist Drill be used to avoid breakage? Use the MetavCUT Twist Drill with appropriate cutting speeds, steady coolant flow and correct feed rates; the short design reduces bending but correct machining parameters and cooling are essential to prevent chipping or fracture. For what is a Twist Drill used? A Twist Drill is mainly applied when machining high‑strength materials and larger drill diameters. Its design allows relatively simple regrinding and it withstands higher loads due to its geometry and material composition. Which three drill types exist? There are three primary drill types: Metal drill, Wood drill, and Stone/Concrete drill. Why are Twist Drills sharpened at the tip? The tip sharpening reduces the cross‑edge at the drill point, lowering friction and thus required feed forces while improving centring of the Twist Drill in the workpiece. Can a metal drill be used for wood? A metal drill can be used in wood, but it offers worse guidance and a less clean result compared with dedicated wood drills; however metal drills are easier to resharpen and have lower self‑feeding tendency. For which drilling depths is the Twist Drill most commonly used? A through hole is typically produced with a Twist Drill. For diameters up to 20 mm and drilling depths up to 100 mm, the Twist Drill is the most frequently used tool. Is HSS or HSSE better? The common assumption that HSSE steels are always superior to HSS is not universally correct; evaluate your working conditions to decide whether the additional cost of HSSE is justified.

Twist Drill — Type N short, 5.9 mm, 135°, 5% cobalt-alloyed, HSS‑E, fully ground shank, DIN 338 The Twist Drill Type N short is a precision metal‑drilling tool designed for Drilling Machines and demanding work on hard materials. Short design for improved stability 5% cobalt‑alloyed HSS‑E for higher heat resistance 135° point angle for hard materials Fully ground shank for precise runout DIN 338 compliant Standard Line Higher performance through material and geometry The combination of HSS‑E and 5% cobalt provides noticeably improved red‑hardness and wear resistance, which means longer tool life when machining tough alloys. The short design reduces cantilever and vibration, resulting in more consistent hole quality and less risk of runout. This configuration is especially sensible where repeatable, clean holes are required and small deviations cannot be tolerated. Optimised for hard materials and precise entry A 135° point angle reduces the tendency to wander and shortens the initial bite when working Stainless Steel or other hard metals, so drilling starts more reliably. The designation Type N denotes the classic spiral geometry for metalwork; it balances chip evacuation and wall finish. For users unfamiliar with point angles: a larger angle produces a flatter tip that spreads cutting forces and reduces chatter on hard materials. Manufacturing method and practical advantages The fully ground flute geometry (HSS‑G style) gives very sharp cutting edges and excellent concentricity, producing clean bores with minimal burr. Ground drills are easier to re‑sharpen and deliver superior roundness compared with roll‑formed equivalents, though they require appropriate coolant and steady feeds to minimise fracture risk. The DIN 338 classification confirms that this short Twist Drill meets standard dimensions and tolerances for professional Metalworking. Suitable applications and handling recommendations Designed for use in Drilling Machines, the short Twist Drill is ideal for precise machining of alloyed and unalloyed steel, cast iron, non‑ferrous metals and engineering plastics. Use moderate cutting speeds and steady feed; apply coolant for stainless and other high‑temperature materials to extend life. If uncertain about speeds or regrinding, METAV Werkzeuge offers expert advice and technical support to match the tool to the application. Strong recommendation for precision metalworking: choose the MetavCUT Twist Drill Type N short for stable, reliable holes — for personalised technical guidance contact METAV Werkzeuge via eMail info@metav-werkzeuge.com, Phone +49 2822 7131930 or WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 47059-FDA Diameter: 5.9 mm Point angle: 135° Type: Type N Material: HSS‑E Execution: short Spiral length: 57 mm Overall length: 93 mm Shank execution: fully ground Model series: Standard Line Norm: DIN 338 Colour: 5% cobalt‑alloyed For: Drilling Machine Application: Drills for metal Packaging unit: 10 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill Type N short used for? The MetavCUT Twist Drill Type N short is primarily applied when machining high‑strength materials and for larger bore diameters; its short geometry increases stability, the shape allows straightforward resharpening and the tool endures higher loads in professional Metalworking. Which three drill types exist? There are three principal drill categories: Metal drills, Wood drills and Stone/Concrete drills; the MetavCUT Twist Drill Type N short belongs to the Metal drills group and is optimised for metal applications.

Introducing the Twist Drill (Type N) — 5 mm diameter · 135° point · short execution · 5% cobalt-alloyed · HSS‑E · DIN 338 · MetavCUT The Twist Drill (Type N) is a short 5 mm metal drilling bit designed for precise work on drilling machines and hardened materials. Short design increases rigidity for precise holes 135° point angle for easier entry in hard metals 5% cobalt-alloyed HSS‑E for improved heat resistance Fully ground shank for high roundness and accuracy Conforms to DIN 338 for standardized reliability Greater precision and reduced deflection for metalworking A short design delivers a tangible advantage in stability: the reduced overhang lowers bending and vibration, so drilling remains accurate even under higher cutting forces. This construction makes the bit especially suited to precision tasks in metalworking where hole roundness and positional accuracy matter. The result is fewer rejects and less rework when producing mating parts or tight-tolerance holes. Material composition that withstands heat and stress Manufactured from HSS‑E with 5% cobalt, the bit offers enhanced hot-hardness compared to standard HSS; this allows higher cutting temperatures without rapid softening. The fully ground geometry creates very sharp cutting edges and excellent concentricity, which improves hole finish. For users unfamiliar with these terms: HSS‑E is a high-speed steel alloyed with cobalt to maintain hardness at elevated temperatures, and "fully ground" means the flute geometry is generated by grinding for superior precision. Clear guidance on application and machine compatibility Designed for use in a Drilling Machine and similar stationary or powered setups, this bit performs well on alloyed and unalloyed steel, cast iron, non‑ferrous metals and many plastics. The flute (spiral) length of 52 mm and overall length of 86 mm balance chip evacuation and rigidity for typical shop tasks. As a Type N normal-spiral configuration, it is optimized for metal work rather than soft wood; for clean woodworking holes, a dedicated wood bit is preferable. Practical handling tips to extend tool life To reduce wear and avoid breakage, employ proper coolant and moderate feed for holes under 6 mm diameter—this short version already lowers the fracture risk but benefits from lubrication. The 135° point angle reduces initial cutting forces and helps the bit enter harder materials with less skidding; when re-grinding becomes necessary, the fully ground geometry is straightforward to restore on suitable equipment. These simple measures extend service life and maintain hole quality. We recommend the MetavCUT Twist Drill Type N for precision metal drilling—if you are unsure whether this tool fits your application or need further technical data, METAV Werkzeuge provides expert advice via eMail: info@metav-werkzeuge.com, Phone: +49 2822 7131930 or WhatsApp: +49 170 2837271. Bezeichnung: Twist Drill Brand: MetavCUT SKU: 47050-FDA Diameter: 5 mm Point angle: 135° Type: Type N Execution: short Colour: 5% cobalt-alloyed Material: HSS‑E Shank execution: fully ground Spiral length (flute): 52 mm Overall length: 86 mm For drilling machine: Drilling Machine Model series: Standard Line Application: Drills for metal Norm: DIN 338 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Can the MetavCUT Twist Drill Type N be used in a handheld drill? The MetavCUT Twist Drill Type N is primarily designed for use in a Drilling Machine for best stability; it can be used in a high-quality handheld drill for light tasks, but reduced overhang, proper clamping and moderate speeds are essential to avoid runout and breakage. For what is a Twist Drill used? A Twist Drill is mainly applied to the machining of high-strength materials and larger drill diameters; it is easy to regrind and withstands higher loads, making it suitable for demanding metalworking operations. Which 3 drill types exist? Common drill categories are Metal Drills, Wood Drills and Masonry/Concrete Drills, with the MetavCUT Twist Drill Type N belonging to the metal drill group.

Spiralbohrer — Twist Drill Type N (Ø 6.1 mm, 135°, short, 5% cobalt-alloyed, HSS‑E, DIN 338) The Spiralbohrer Twist Drill Type N is a short HSS‑E drill designed for precision drilling in metal with enhanced stability and wear resistance. Short design for higher stability 135° point angle for hard materials HSS‑E with 5% cobalt for wear resistance Fully ground shank for precise centring DIN 338 compliance for standardised quality Increased Precision and Stability for Metalworking A short Twist Drill with reduced overall length improves stability and reduces bending during operation, which is especially important when working with tougher metals. The combination of a short design and a fully ground shank ensures consistent concentricity in the chuck and cleaner holes under load. Professionals who demand repeatable, accurate results will value the greater rigidity compared with longer counterparts, making this tool well suited for demanding drilling tasks in workshop and production environments. Material Composition and Why 5% Cobalt Matters The HSS‑E material with 5% cobalt increases hot hardness and wear resistance, allowing the Twist Drill to retain cutting performance at higher temperatures typical when drilling stainless steel and alloyed steels. The cobalt alloy improves service life and reduces frequent regrinding cycles, so fewer tool changes are required during longer runs. For users unfamiliar with HSS‑E, it is a high‑speed steel variant alloyed for improved durability when cutting hard materials. Optimised Geometry for Hard Materials With a 135° point angle and Type N normal spiral geometry, this short Twist Drill is optimised for entering and cutting harder materials while reducing walking and chatter on the surface. The larger point angle reduces the tendency to dig in on the first contact and shortens the effective penetration time, which benefits drilling in stainless steel and similar alloys. For routine metal fabrication tasks where precision and tool life matter, this geometry provides a reliable balance between entry behaviour and chip evacuation. Intended Use and Who Benefits Most Designed primarily as a drill for metal, this Twist Drill Type N suits metalworkers, toolroom technicians and production engineers requiring reliable holes in alloyed and unalloyed steel, cast iron, non‑ferrous metals and plastics. The short execution makes it ideal for bench drills and smaller drilling machines where minimised overhang leads to better outcomes. If the application involves long reach or deep through‑holes, a different drill length should be selected to match the task. Handling, Cooling and Regrinding Tips To get the best lifetime from a short HSS‑E Twist Drill, use appropriate cutting speeds, steady feed and suitable coolant when machining harder alloys. The fully ground flute geometry provides sharp cutting edges and precise hole quality but can be more brittle than rolled alternatives; therefore controlled feeds and coolant reduce thermal stress and risk of breakage. When regrinding, keep the original point geometry to maintain the centring behaviour and the characteristic 135° angle for hard materials. For precise metal drilling choose MetavCUT quality: the short Twist Drill Type N offers the stability and heat resistance that professionals value — for technical questions or personalised advice contact METAV Werkzeuge. 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp +49 170 2837271 Technical information Designation: Twist Drill Brand: MetavCUT SKU: 47061-FDA Diameter: 6.1 mm Spiral length: 63 mm Overall length: 101 mm Point angle: 135° Type: Type N Execution: short Material: HSS‑E Colour: 5% cobalt-alloyed Shank finish: fully ground For drilling machine: Drilling Machine Norm: DIN 338 Application: Drills for metal Model series: Standard Line Manufacturer: MetavCUT Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Spiralbohrer Twist Drill Type N best used for? The Spiralbohrer Twist Drill Type N by MetavCUT is primarily intended for drilling metal; its short execution and Type N geometry make it particularly suitable for precision holes in alloyed and unalloyed steels, cast iron, non‑ferrous metals and plastics. Can the Spiralbohrer Twist Drill be used on stainless steel and hard alloys? Yes. The Spiralbohrer Twist Drill Type N with HSS‑E material and 5% cobalt from MetavCUT is designed for higher hot hardness and wear resistance, which improves performance when drilling stainless steel and other harder alloys. For what is a Twist Drill used? A Twist Drill is mainly applied when machining high‑strength materials and larger drill diameters. This form is easy to regrind and withstands higher loads, which is why it is commonly used for tougher metalworking operations. Which three drill types exist? The main categories are metal drills, wood drills and stone/concrete drills. Why are Twist Drills tip‑pointed (ausgespitzt)? The tip pointing reduces the cross‑cut at the drill tip, which significantly lowers friction and therefore requires less feed force. At the same time the pointed tip centres the drill more reliably in the workpiece. Can a Twist Drill be used to drill wood? A metal drill can be used in wood, but guidance is poorer and the hole finish is less clean. Metal drills are easier to regrind and have lower self‑feed tendency compared with dedicated wood bits. For which drilling depths is the Twist Drill most used? A solid hole is typically produced with a Twist Drill. For diameters up to 20 mm and depths up to 100 mm, the Twist Drill is the most commonly used tool. Is HSS or HSSE better? The common belief that HSSE steels are always superior to standard HSS is not universally true. When choosing, assess whether your working conditions justify the higher initial cost of HSSE for the expected benefits.

Twist Drill (Type N) — 6.2 mm, 135° tip, short HSS‑E, 5% cobalt‑alloyed, DIN 338 — MetavCUT A Twist Drill (Type N) designed for precise metal drilling, combining a 6.2 mm diameter and a 135° tip angle in a short, stable execution suitable for demanding machining tasks. Type N Twist Drill, 6.2 mm diameter 135° tip angle for hard materials Short execution for higher stability HSS‑E with 5% cobalt for improved toughness Fully ground shank, DIN 338 compliant Exceptional stability and precision for metalworking Short-form drills deliver measurable advantages when precision matters. The short design of this MetavCUT Twist Drill reduces the unsupported overhang, which increases stability and lowers the tendency to wander or bend under load. Combined with the 135° tip angle, the geometry shortens pilot time and improves centring in harder materials. For production environments that require repeatable hole quality, the shorter spiral length also reduces vibration and contributes to more consistent hole diameter and surface finish. Material composition for longer life under stress Constructed from HSS‑E and alloyed with 5% cobalt, this short Twist Drill offers higher hot hardness and greater wear resistance than standard HSS. The cobalt content increases toughness at elevated temperatures, making the tool more suitable for drilling alloyed and unalloyed steel, cast iron, non‑ferrous metals and certain plastics. The fully ground flute geometry provides very sharp cutting edges and high running accuracy; however, grinding can increase brittleness, so coolant use and stable clamping are recommended to maximise tool life. Designed for drilling machines and demanding applications Classified to DIN 338, this Type N drill is the classical metal drill geometry optimised for machining of metallic workpieces on drilling machines. The shorter overall length and fully ground spiral make it particularly suited to stationary machines and operations that require high precision rather than freehand drilling. Typical applications include workshop fabrication, maintenance, toolmaking and any task where controlled drilling into Steel and similar materials is required. Note that Type N is not optimised for very soft materials where specialised geometries perform better. Practical advice for safe and efficient use When using the MetavCUT Twist Drill, ensure secure clamping and appropriate coolant or cutting fluid to dissipate heat and extend tool life. Start with a light feed to establish the hole, especially in harder materials, and avoid excessive spindle speeds that can overheat the tip. The 135° point reduces entry forces and improves centring for harder alloys, while the short execution minimises deflection—both contributing to cleaner, more accurate holes. For portable handheld drilling machines, consider the shorter projection to reduce user fatigue and increase control. The MetavCUT short Twist Drill (Type N) is recommended for professionals seeking stable, precise metal drilling; for expert technical advice or to confirm suitability for specific tasks contact METAV Werkzeuge — Email: info@metav-werkzeuge.com • Phone: +49 2822 7131930 • WhatsApp: +49 170 2837271 Twist Drill Brand: MetavCUT SKU: 47062-FDA Diameter: 6.2 mm Overall length: 101 mm Spiral length: 63 mm Tip angle: 135° Type: Type N Execution: short Material: HSS‑E Colour: 5% cobalt‑alloyed Shank design: fully ground Series: Standard Line Standard: DIN 338 For drilling machine: Drilling Machine Application: Drills for metal Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill (Type N) mainly used for? The MetavCUT Twist Drill (Type N) is primarily applied for machining high‑strength materials and larger bore diameters. Its short form suits precise work and makes the drill easier to re‑grind while maintaining resistance to higher loads in metalworking operations. Which three drill types exist? There are three common drill types: metal drills, wood drills and stone/concrete drills. The MetavCUT Twist Drill (Type N) belongs to the metal drill category, optimised for use in metalworking environments. Why are Twist Drills pointed? The point geometry reduces the cross‑cut at the tip of a Twist Drill, which lowers friction and thus requires smaller feed forces. By sharpening the tip, the drill centres more reliably in the workpiece and cuts with less resistance, improving entry behaviour and hole quality. Can you use a Twist Drill to drill wood? A metal drill such as the MetavCUT Twist Drill (Type N) can be used in wood, but guidance and centring are generally poorer and the finish may be less clean compared with purpose‑made wood bits. Metal drills are easier to re‑grind and show less self‑feed, which can be an advantage in some hobby or repair scenarios. For which drilling depths is the Twist Drill most commonly used? A through hole in a solid piece is typically executed with a Twist Drill. For diameters up to 20 mm and drilling depths up to 100 mm, the Twist Drill is the most frequently used tool. The MetavCUT Twist Drill (Type N) is therefore appropriate for many standard metal drilling tasks. What is better, HSS or HSSE? The common assumption that HSSE steels are always superior to standard HSS is not universally correct. Choose between HSS and HSSE based on actual working conditions and whether the higher purchase cost of HSSE is justified by the specific performance benefits required.

Twist Drill (Type N) — 6.3 mm, 135° Tip, Short, 5% Cobalt‑Alloyed, HSS‑E, DIN 338 The Twist Drill Type N is a short HSS‑E drill designed for precise metal drilling with hand and drilling machines, offering high stability and wear resistance in demanding machining tasks. Short design for improved stability and precision 5% Cobalt‑alloyed HSS‑E for increased heat resistance 135° Tip angle for harder materials and stainless steel Fully ground shank for excellent runout accuracy Conforms to DIN 338 for standardised short twist drills Exceptional Stability and Accurate Hole Making for Metalworking Short Spiral Geometry delivers a measurable benefit in everyday machining: the reduced overhang increases Stability and cuts down on bit deflection, so holes come out truer to size. This Short Twist Drill with a 63 mm Spiral Length and 101 mm Overall Length is particularly suited to operations where rigidity matters, such as drilling in steel or when using a Hand Drilling Machine. The 135° Tip shortens initial entry time in harder materials and helps maintain centring under load. Enhanced Material Properties for Longer Life under Heat and Load Manufactured from HSS‑E with 5% Cobalt, this Twist Drill offers greater red hardness and wear resistance compared with conventional HSS. The cobalt‑alloyed composition means the tool tolerates higher cutting temperatures and preserves cutting edges longer when machining alloyed and unalloyed steel, cast iron and non‑ferrous metals. HSS‑E (High Speed Steel with Cobalt) describes a faster heat‑resistant steel grade that balances toughness with hardness, reducing the need for frequent tool changes. Precision Grinding and Standard Compliance for Reliable Results The fully ground flute geometry produces very sharp cutting edges and high concentricity, yielding clean, accurate bores in metal. As defined by DIN 338, this Short Twist Drill is produced to standardised dimensions and tolerances for short drills with cylindrical shanks. Ground tools typically give better hole quality than roll‑formed alternatives; they are easier to resharpen but require proper cooling and appropriate speeds to avoid premature breakage. Optimised for Metal Applications and Practical Use Recommendations Designed as a classic Type N normal‑spiral metal drill, this tool is recommended for a range of metalworking tasks on both stationary and portable drilling equipment. The shorter cutting length reduces the risk of bending and is therefore ideal for precision holes and tougher materials. For best results, use suitable cutting speeds, adequate lubrication or coolant when drilling stainless or hardened steels, and secure the workpiece to minimise vibration. The construction allows for easier regrinding when required, extending service life. Strong recommendation: Choose the MetavCUT HSS‑E short Twist Drill for precise, high‑duty metal drilling — for personalised technical advice and application support contact METAV Werkzeuge; eMail: info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 47063-FDA Type: Type N Diameter: 6.3 mm Overall length: 101 mm Spiral length: 63 mm Point angle: 135° Material: HSS‑E Cobalt content: 5% cobalt‑alloyed Execution: Short Shank finish: Fully ground Conforms to: DIN 338 Application: Drills for metal Suitable for: Drilling Machine (Hand Drilling Machine) Model series: Standard Line Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the best use for the MetavCUT Twist Drill Type N? The MetavCUT Twist Drill Type N is primarily used for machining high‑strength materials and larger drill diameters; its short design and HSS‑E composition make it easier to resharpen and capable of withstanding higher loads during metalworking. Which three drill types are commonly distinguished? In general practice the main categories are Metal drills, Wood drills and Stone/Concrete drills; the MetavCUT Twist Drill belongs to the metal drill category and is optimised for steel and similar materials. Why are Twist Drills sharpened at the point? The point sharpening reduces the cross‑cut at the tip of the Twist Drill, lowering friction and therefore the required feed forces; additionally, a properly sharpened tip improves centring in the workpiece. Can a metal Twist Drill be used to drill wood? A metal drill such as the MetavCUT Twist Drill can be used in wood, but guidance and finish are typically inferior compared with dedicated wood drills; metal drills are easier to resharpen and exhibit less self‑feeding in soft materials. For which drilling depths is the Twist Drill most commonly used? A through hole in solid material is often executed with a Twist Drill; for diameters up to about 20 mm and drilling depths up to approximately 100 mm the Twist Drill is the most frequently used tool.

Twist Drill Type N — 6.4 mm, 135°, short, 5% cobalt-alloyed, HSS‑E, DIN 338 The Twist Drill Type N is a short HSS‑E metal drill designed for precise work in Hand Drilling Machines and stationary setups. Short design for increased rigidity and accuracy 135° point angle for hard materials like stainless steel HSS‑E with 5% cobalt for improved heat resistance Fully ground shank for high concentricity and clean holes Compliant with DIN 338 for short twist drills Greater Precision through a Short, Stable Design The short configuration of this Twist Drill minimises overhang and produces higher stability during drilling, which directly benefits precision and reduces the risk of wandering. The fully ground Shank delivers excellent concentricity, resulting in cleaner, rounder holes in Metal. For operators seeking reproducible results on benches or in jigs, the reduced tendency to deflect means less rework and better fit for threaded components. Suited to Hard Materials — Faster Penetration, Better Control With a 135° Point Angle and the Type N Normal Spiral geometry, this short HSS‑E tool is optimised for demanding tasks in Steel, Cast Iron and other hard materials. The geometry shortens initial touch‑in time and helps maintain the centre when starting a hole. Compliance with DIN 338 indicates manufacture to accepted dimensions and tolerances for short twist drills, supporting consistent performance across batches and easy integration in production workflows. Practical Guidance for Efficient Use Use the Twist Drill in a suitable Drilling Machine with adequate clamping and coolant to extend tool life. The 5% cobalt-alloyed composition increases heat resistance, allowing for higher cutting temperatures and improved wear stability; nevertheless, coolant or lubricant is advised for continuous or deep drilling. The shorter overall length favours operations where stiffness and tool control are critical, such as drilling into thicker plates or working with tight positional tolerances. Material and Handling Benefits from HSS‑E Chemistry The HSS‑E grade combined with 5% cobalt yields a balance of hardness and toughness that performs well under thermal load. The Standard Line production and the fully ground flute geometry create sharp cutting edges and excellent runout characteristics. Operators should note that ground drills offer superior hole quality but can be more brittle than rolled alternatives; therefore, controlled feed rates and proper cooling will help prevent chipping and extend service intervals. Strong recommendation: Choose the MetavCUT short Twist Drill for demanding metal applications and contact METAV Werkzeuge for expert advice and personalised support — eMail: info@metav-werkzeuge.com · Phone: +49 2822 7131930 · WhatsApp: +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 47064-FDA Type: Type N Diameter: 6.4 mm Point Angle: 135° Execution: short Overall Length: 101 mm Spiral Length: 63 mm Material: HSS‑E Colour / Surface: 5% cobalt-alloyed Shank: fully ground Application: Drills for metal For Drilling Machine: Drilling Machine Model Series: Standard Line Norm: DIN 338 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill Type N used for? The MetavCUT Twist Drill Type N is primarily used for drilling Metal and is suitable for demanding applications where a short, stiff tool is required. It is especially effective on harder materials thanks to the 135° point angle and HSS‑E chemistry, which together improve centring and heat resistance. For what is a Twist Drill used? A Twist Drill is mainly applied to the machining of high‑strength materials and larger bore diameters. Its form allows relatively simple resharpening and it withstands higher loads. This geometry is commonly used where durability and the ability to drill tough materials are required. Which 3 drill types are there? Common classifications are Metal drills, Wood drills, and Masonry/Concrete drills. Why are Twist Drills point‑ground? Point grinding reduces the cross‑cut at the tip of the Twist Drill, which lowers friction and consequently the required feed forces. In addition, a ground tip improves centring in the workpiece and leads to more accurate, controlled drilling.

Twist Drill — Type N, 6.5 mm, 135° tip, short, 5% cobalt-alloyed, HSS‑E, DIN 338 The Twist Drill Type N is a short HSS‑E metalworking drill designed for stable, precise holes in hard materials when used with a Drilling Machine. Short construction for increased stability 6.5 mm diameter for standard metalwork 135° tip for clean penetration in hard steels 5% cobalt‑alloyed HSS‑E for enhanced wear resistance Fully ground shank for high concentricity Durable alloy and compact design for demanding metalwork The HSS‑E composition with 5% cobalt gives this short twist drill exceptional heat resistance and wear stability when machining tough alloys. Because the design is short, the tool exhibits reduced overhang and less flexing, which directly improves hole accuracy and tool life under heavy cutting loads. This makes the drill particularly suitable for precision tasks such as locating holes in jigs and producing repeatable diameters in alloyed and unalloyed steel. Geometry and finish that improve hole quality and centring A fully ground flute geometry yields very sharp cutting edges and excellent concentricity; the typical result is cleaner chips and reduced burr formation. The 135° tip angle reduces thrust and improves entry in hard materials such as stainless steel, shortening the initial contact phase and helping to avoid wandering. As a Type N normal‑spiral twist drill, it balances chip evacuation and cutting stability for general metalworking. Recommended applications and suitable materials This short Twist Drill is engineered for use in metalworking: it performs well on alloyed and unalloyed steel, cast iron, non‑ferrous metals and many plastics. The compact length is an asset when working with hand or bench drilling machines where rigidity is crucial. Note that Type N geometry is not optimised for very soft woods; for woodworking, specialist drills provide better guidance and surface finish. Handling, cooling and reconditioning advice for longer life To maintain performance, use appropriate cutting speeds and a cutting fluid when machining steels; cooling reduces tool wear and the risk of tempering the cutting edge. Because the drill is manufactured ground, it can be resharpened by a skilled operator to restore the cutting lip and prolong service life. Observing correct feed and speed settings for the material ensures reliable hole quality and minimises breakage risk. We recommend MetavCUT’s Twist Drill Type N for precise metalworking — for personal technical advice or to confirm suitability for your application, contact METAV Werkzeuge: info@metav-werkzeuge.com | +49 2822 7131930 | WhatsApp +49 170 2837271 Designation: Twist Drill Marke: MetavCUT SKU: 47065-FDA Diameter: 6.5 mm Tip angle: 135° Spiral length: 63 mm Overall length: 101 mm Execution: short Type: Type N Material: HSS‑E Colour: 5% cobalt‑alloyed Shank finish: fully ground Model series: Standard Line Norm: DIN 338 For machine: Drilling Machine Application: Drills for metal Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill Type N best used for? The MetavCUT Twist Drill Type N is primarily used for metalworking; it excels when drilling alloyed and unalloyed steels, cast iron and other hard materials, offering good general performance on rotating drilling machines. Can the MetavCUT Twist Drill be used in a hand drilling machine? Yes, the short design of the MetavCUT Twist Drill makes it especially stable in hand and bench Drilling Machines, reducing the tendency to bend and improving hole accuracy when correct speeds and cooling are applied. What are Twist Drills used for? Twist Drills are mainly applied when machining high‑strength materials and larger diameters. Their form allows relatively simple resharpening and they withstand higher loads, making them suitable for robust metalworking tasks. Which three drill types exist? The three primary drill categories are metal drills, wood drills and stone/concrete drills.

Twist Drill — Type N Short, 6.6 mm, 135° Point, HSS‑E, 5% Cobalt‑Alloyed (DIN 338, Fully Ground) The bold Twist Drill Type N short is designed for precision metalworking and offers enhanced stability and wear resistance for use in drilling machines and hand drills. Short design increases stability and precision 5% Cobalt‑alloyed HSS‑E for hard materials 135° point angle for reduced chipping in steel Fully ground flutes for accurate, clean holes Conforms to DIN 338 for short twist drills Optimised strength for demanding metal applications The HSS‑E composition with 5% cobalt gives the short Twist Drill improved hot hardness and wear resistance compared with standard HSS. This makes it particularly suitable for drilling alloyed and unalloyed Steel, Cast Iron, non‑ferrous metals and engineering Plastics. The shorter overall length reduces overhang and flex, resulting in higher concentricity and a lower risk of breakage when working with tougher materials. The combination of material and compact geometry therefore supports longer tool life under higher thermal and mechanical stress. Geometry that produces cleaner, more accurate holes A 135° point angle and fully ground flute geometry ensure reliable centring and a smoother entry into harder workpieces. The CNC grinding of the flute geometry (HSS‑G style) yields sharp cutting edges and a high runout accuracy, which produces precise, burr‑reduced holes. The flute (spiral) length of 63 mm is matched to a total length of 101 mm, optimising chip evacuation while maintaining rigidity. For projects that demand clean, dimensionally accurate bores, this ground short design offers clear advantages over rolled alternatives. Best practice: machines, materials and typical uses Designed as a classic Type N Twist Drill, this short variant is intended primarily for Drilling Machines but is compatible with robust hand drills when used with appropriate clamping and coolant. It excels in general metalworking tasks such as through‑holes in structural components, toolroom operations and maintenance work where stability and repeatable hole quality matter. For stainless steels and other hard alloys, use moderate speeds, steady feed and cooling to exploit the cobalt alloy’s high temperature performance. Handling, cooling and reconditioning guidance To preserve cutting performance, apply suitable cutting fluid for metalworking and avoid excessive speed that raises temperature rapidly. The fully ground tip provides excellent initial cutting action but can be more brittle than rolled designs; controlled feed rates and steady clamping are recommended. When regrinding is required, the ground geometry allows precise resharpening, but attention must be paid to the point angle to retain the 135° profile. For stationary and production environments, recommended use is with coolant and secure fixturing to prevent chipping and extend service life. Strong recommendation: For precision metal drilling tasks choose the MetavCUT Twist Drill Type N short with 5% cobalt‑alloyed HSS‑E for superior stability and durability — for tailored advice or technical support contact METAV Werkzeuge directly via email at info@metav-werkzeuge.com, by phone at +49 2822 7131930 or WhatsApp at +49 170 2837271 Designation: Twist Drill (Short, Type N) Brand: MetavCUT SKU: 47066‑FDA Diameter: 6.6 mm Point angle: 135° Type: Type N Colour / Composition: 5% cobalt‑alloyed Execution: Short Material: HSS‑E Shaft finish: Fully ground Spiral (flute) length: 63 mm Total length: 101 mm Model series: Standard Line Standard / Norm: DIN 338 Suitable for: Drilling Machine (Hand Drill compatible with precautions) Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What are Twist Drills used for and when is a short Type N advantageous? The MetavCUT Twist Drill Type N short is used primarily for machining metal; its short geometry gives increased stability and is therefore advantageous for precision holes in harder materials and applications where reduced overhang prevents bending and breakage. Which three main drill types exist? Common distinctions are Metal drills, Wood drills and Stone/Concrete drills; the MetavCUT Twist Drill Type N belongs to the metal drill category and is optimised for metalworking tasks. Can the MetavCUT Twist Drill be used in a hand drill? The MetavCUT Twist Drill Type N short can be used in a robust hand drill, but optimal results are achieved with a drilling machine; secure clamping and coolant are recommended to prevent chatter and extend tool life. Why is the tip of a twist drill ground (pointed)? The ground point on the MetavCUT Twist Drill reduces the chisel edge at the tip, lowering friction and required feed forces while improving centring in the workpiece, which results in easier penetration and more accurate holes.

MetavCUT Twist Drill – Type N, Short, 6.7 mm, 135° Tip, 5% Cobalt-alloyed, HSS‑E, DIN 338 The MetavCUT Twist Drill is a short Type N metal drill designed for precise work in drilling machines, featuring a 6.7 mm diameter, a 135° tip angle and a 5% cobalt‑alloyed HSS‑E construction for enhanced heat resistance. Short design for improved stability and accuracy 135° tip for reliable entry in hard materials 5% cobalt‑alloyed HSS‑E for higher heat resistance Fully ground flutes for precise roundness and clean holes Conforms to DIN 338 for short twist drills Short design that reduces deflection and improves hole quality Thanks to its short Execution the drill offers a reduced overhang from the chuck, which increases Stability and minimises bending during machining. This results in cleaner Holes and better concentricity when working with metals. The reduced free length is particularly beneficial for operations that demand repeatable precision and lower runout on drilling machines. Materials and geometry tuned for hard metals The combination of HSS‑E material with 5% cobalt and a 135° Tip Angle improves wear resistance and thermal stability during high‑temperature cutting. A larger tip angle shortens initial penetration and spreads cutting forces, making this tool suitable for stainless steel and other harder alloys where conventional angles can cause chatter or premature wear. Ground flutes and DIN 338 quality for accurate machining The fully ground flute geometry (HSS‑G style) ensures sharp cutting edges and tight dimensional tolerance, producing precise, burr‑reduced bores. As a DIN 338 short twist drill, manufacturing tolerances and shank dimensions comply with the standard, which supports consistent clamping and repeatable results in production environments. Recommended 사용 and handling for best results For optimal performance fit the tool into a stable drilling machine and apply adequate coolant when machining steel or stainless alloys. The flute length of 63 mm and an overall length of 101 mm provide a balance between reach and rigidity for a 6.7 mm diameter. Use moderate feed rates and maintain concentric clamping to exploit the Short Design and avoid excessive side forces that may lead to chipping. Target users and typical applications Engineers, toolroom technicians and maintenance professionals benefit from the MetavCUT Standard Line short twist drill when drilling holes in alloyed and unalloyed steel, cast iron, non‑ferrous metals and engineering plastics. The tool is aimed at users who prioritise accuracy, repeatability and straightforward regrindability for maintenance and repair tasks. Strong recommendation: choose the MetavCUT Standard Line Twist Drill for precision metalworking; for advice on suitability, alternative geometries or cutting data contact METAV Werkzeuge — eMail: info@metav-werkzeuge.com — Tel: +49 2822 7131930 — WhatsApp: +49 170 2837271 Designation: Twist Drill (Short Spiral Drill) Brand: MetavCUT SKU: 47067-FDA Diameter: 6.7 mm Tip angle: 135° Type: Type N Material: HSS‑E (5% Cobalt‑alloyed) Execution: Short Shank finish: Fully ground Flute length: 63 mm Overall length: 101 mm Colour / Alloy note: 5% cobalt‑alloyed For drilling machine: Drilling Machine (Handheld machines possible with care) Model series: Standard Line Standard: DIN 338 Application: Drills for metal Manufacturer: MetavCUT Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill used for? The MetavCUT Twist Drill (Type N) is primarily applied to the machining of high‑strength metals and larger drill diameters; its short design and robust HSS‑E composition make it suitable for precise metal drilling tasks where stability and wear resistance are required. Which three drill types exist? In general drill classification there are three main groups: metal drills, wood drills and stone/concrete drills; the MetavCUT Twist Drill belongs to the metal‑drill category and is optimised for metalworking on drilling machines. Why are Twist Drills point‑ground? Point grinding reduces the web thickness at the tip of a twist drill, decreasing friction and lowering the required feed forces; as a result the drill centres more reliably in the workpiece and needs less thrust, which improves entry accuracy for the MetavCUT Twist Drill.

Spiralbohrer von MetavCUT – HSS-E, 6,8 mm, 135°, Typ N, 5% Kobaltlegierung, kurz, geschliffen, DIN 338 Der Spiralbohrer von MetavCUT ist ein kurzer HSS-E Metallbohrer nach DIN 338 für präzise und stabile Bohrungen in legiertem und unlegiertem Stahl sowie Guss. Kurzbauform für erhöhte Stabilität beim Bohren HSS-E mit 5% Kobaltlegierung für längere Standzeit Geschliffene Schaftausführung für hohe Rundlaufgenauigkeit Spitzenwinkel 135° reduziert Neigung zum Auswandern Geeignet für Handbohrmaschine und stationäre Säulenbohrmaschine Hohe Stabilität bei präzisen Metallbohrungen Die kurze Ausführung sorgt für eine deutlich reduzierte Auskraglänge und damit für mehr Stabilität und geringere Vibrationen beim Bohren. Durch die kurze Geometrie wird das Risiko von Durchbiegung minimiert, was insbesondere bei härteren Werkstoffen zu saubereren Bohrbildern führt. Der Einsatz von HSS-E mit 5% Kobaltlegierung erhöht die Wärmebeständigkeit und reduziert Werkzeugverschleiß auch bei höheren Schnittgeschwindigkeiten und intermittierendem Kühlmitteleinsatz. Optimaler Einsatzbereich für handgeführte Maschinen und Werkstätten Mit einem Durchmesser von 6,8 mm liegt der Bohrer im Standard-Bereich und ist ideal für gängige Werkstatt‑ und Montageaufgaben. Die Geometrie Typ N macht das Werkzeug geeignet für das Bohren in Dünnmaterialien sowie mittleren Blechen aus Stahl, Aluminium und Nichteisenmetallen. Bei handgeführten Geräten empfiehlt sich ein kontrollierter Vorschub und gegebenenfalls Vorstechen mit einem Zentrierbohrer, um saubere Einstiche und gleichmäßigen Spanfluss zu gewährleisten. Geschliffen für präzise Passungen und saubere Bohrlöcher Die geschliffene Fertigung liefert eine hohe Rundlaufgenauigkeit und scharfe Schneidenkanten, wodurch exakte Bohrungen und gute Oberflächengüten erreicht werden. Im Vergleich zur rollgewalzten Ausführung bietet der CNC‑Schliff Vorteile bei Maßhaltigkeit und Lochqualität, weshalb diese Variante bevorzugt für präzise Metallbearbeitung eingesetzt wird. Der Spitzenwinkel 135° unterstützt das Anbohren harter Materialien und reduziert das Wandern des Bohrers auf der Oberfläche. Hinweise zur Anwendung und Pflege für lange Standzeiten Für dauerhaft gute Ergebnisse empfiehlt sich die Verwendung geeigneter Kühlschmierstoffe bei Bohrungen in gehärteten oder wärmeleitfähigen Werkstoffen sowie kontrollierte Drehzahlen. Bei einem Durchmesser von 6,8 mm ist direktes Bohren möglich; für hochpräzise Passungen kann das Anpunkten mit einem Zentrierbohrer die Genauigkeit erhöhen. Regelmäßiges Nachschleifen bzw. Austausch beim Verschleiß bewahrt die Schnittqualität und verlängert die Lebensdauer des Werkzeugs. Empfehlung: Den MetavCUT Standard Line Spiralbohrer für anspruchsvolle Metallbohrungen verwenden und bei Fragen die technische Beratung von METAV Werkzeuge per eMail oder Telefon in Anspruch nehmen Technische Daten Bezeichnung: Spiralbohrer Marke: MetavCUT SKU: 47068-FDA Durchmesser: 6,8 mm Material: HSS-E Farbe / Legierung: 5% Kobaltlegiert Ausführung: kurz Schaft Ausführung: geschliffen Gesamtlänge: 109 mm Spirallänge: 69 mm Spitzenwinkel: 135° Typ: Typ N Norm: DIN 338 Modellserie: Standard Line Für Bohrmaschine: Handbohrmaschine Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Wie eignet sich der Spiralbohrer von MetavCUT für Edelstahlbohrungen? Der Spiralbohrer von MetavCUT in HSS-E Ausführung mit 135° Spitzenwinkel ist für härtere Werkstoffe geeignet; bei Edelstahl empfiehlt sich die Nutzung von Kühlschmierstoff und angepasster Drehzahl, um Überhitzung zu vermeiden und die Standzeit zu erhöhen. Kann der Spiralbohrer von MetavCUT mit einer Handbohrmaschine verwendet werden? Ja, der kurze HSS-E Spiralbohrer ist ausdrücklich für den Einsatz mit Handbohrmaschine und stationären Maschinen vorgesehen, wobei die kurze Auskraglänge die Stabilität bei handgeführten Anwendungen verbessert. Worin unterscheiden sich geschliffene und rollgewalzte Spiralbohrer in der MetavCUT Standard Line? Bei der MetavCUT Standard Line bedeutet geschliffen eine höhere Rundlaufgenauigkeit und schärfere Schneiden, was präzisere Bohrungen ermöglicht; rollgewalzte Bohrer sind tendenziell zäher, während geschliffene Werkzeuge bei hoher Präzision und Werkstoffhärte Vorteile bringen. Welche Materialien lassen sich mit dem MetavCUT Spiralbohrer bearbeiten? Der Spiralbohrer von MetavCUT eignet sich für legierten und unlegierten Stahl, Gusseisen, Nichteisenmetalle sowie Kunststoffe; für sehr zähe oder gehärtete Materialien ist auf passende Schnittbedingungen und Kühlung zu achten. Sind Sie sich nicht sicher, ob dieses Werkzeug Ihre Anforderungen erfüllt oder benötigen Sie ergänzende technische Daten? Kein Problem – METAV Werkzeuge bietet umfassende Beratung per eMail unter info@metav-werkzeuge.com, Telefon +49 2822 7131930 oder WhatsApp +49 170 2837271. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#47068-FDA","sku":"47068-FDA","mpn":"47068-FDA","name":"Spiralbohrer 47068-FDA","description":"Kurz ausgeführter HSS-E Spiralbohrer mit 5% Kobaltlegierung, 6,8 mm Durchmesser, 135° Spitzenwinkel, Typ N, geschliffener Schaft nach DIN 338 für präzise Metallbohrungen in legiertem und unlegiertem Stahl, Gusseisen, Nichteisenmetallen und Kunststoffen.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741b/logo-metav-1200-1200.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741e/logo-metav-1200-900.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png"],"additionalProperty":[{"@type":"PropertyValue","name":"Bezeichnung","value":"Spiralbohrer"},{"@type":"PropertyValue","name":"Durchmesser","value":"6,8 mm"},{"@type":"PropertyValue","name":"Spitzenwinkel","value":"135°"},{"@type":"PropertyValue","name":"Typ","value":"Typ N"},{"@type":"PropertyValue","name":"Farbe / Legierung","value":"5% Kobaltlegiert"},{"@type":"PropertyValue","name":"Ausführung","value":"kurz"},{"@type":"PropertyValue","name":"Material","value":"HSS-E"},{"@type":"PropertyValue","name":"Schaft Ausführung","value":"geschliffen"},{"@type":"PropertyValue","name":"Norm","value":"DIN 338"},{"@type":"PropertyValue","name":"Gesamtlänge","value":"109 mm"},{"@type":"PropertyValue","name":"Spirallänge","value":"69 mm"},{"@type":"PropertyValue","name":"Modellserie","value":"Standard Line"},{"@type":"PropertyValue","name":"Für Bohrmaschine","value":"Handbohrmaschine"},{"@type":"PropertyValue","name":"Hersteller","value":"MetavCUT"},{"@type":"PropertyValue","name":"Anwendung","value":"Bohrer für Metall"},{"@type":"PropertyValue","name":"Verpackungseinheit","value":"10"},{"@type":"PropertyValue","name":"preis_netto","value":"4.21 EUR"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"Wie eignet sich der Spiralbohrer von MetavCUT für Edelstahlbohrungen?","acceptedAnswer":{"@type":"Answer","text":"Der Spiralbohrer von MetavCUT als HSS-E mit 5% Kobaltlegierung und 135° Spitzenwinkel eignet sich für härtere Werkstoffe; bei Edelstahl sollten Kühlschmierstoff und angepasste Drehzahlen eingesetzt werden, um Überhitzung zu vermeiden und die Standzeit zu erhöhen."}},{"@type":"Question","name":"Kann der Spiralbohrer von MetavCUT mit einer Handbohrmaschine verwendet werden?","acceptedAnswer":{"@type":"Answer","text":"Ja, der kurze HSS-E Spiralbohrer von MetavCUT ist für Handbohrmaschine und stationäre Maschinen vorgesehen; die kurze Auskraglänge erhöht die Stabilität bei handgeführten Anwendungen."}},{"@type":"Question","name":"Worin unterscheiden sich geschliffene und rollgewalzte Spiralbohrer in der MetavCUT Standard Line?","acceptedAnswer":{"@type":"Answer","text":"Geschliffene Spiralbohrer bieten höhere Rundlaufgenauigkeit und schärfere Schneiden für präzisere Bohrungen, während rollgewalzte Bohrer tendenziell zäher sind; geschliffene Ausführungen sind besonders für harte Werkstoffe und präzise Anwendungen geeignet."}},{"@type":"Question","name":"Welche Materialien lassen sich mit dem MetavCUT Spiralbohrer bearbeiten?","acceptedAnswer":{"@type":"Answer","text":"Der MetavCUT Spiralbohrer eignet sich für legierten und unlegierten Stahl, Gusseisen, Nichteisenmetalle sowie Kunststoffe; bei sehr zähen oder gehärteten Materialien sind passende Schnittbedingungen und Kühlung zu beachten."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/spiralbohrer-47068-FDA","dateModified":"2026-05-04T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Spiralbohrer HSS-E kurz"},{"@type":"Thing","name":"DIN 338"},{"@type":"Thing","name":"MetavCUT Standard Line"}],"mentions":[{"@type":"Thing","name":"geschliffener Schaft"},{"@type":"Thing","name":"5% Kobaltlegierung"},{"@type":"Thing","name":"Typ N Normalspirale"},{"@type":"Thing","name":"Einsatz in Handbohrmaschine und stationären Maschinen"}]}]}

Twist Drill — Type N short, 6.9 mm Diameter · 135° Tip · 5% Cobalt-alloyed · HSS‑E · DIN 338 (MetavCUT) The Twist Drill Type N short by MetavCUT is a precision metalworking drill designed for Drilling Machines and engineered for stable, accurate holes in harder materials. Short design for higher stability and precision 135° tip geometry for harder materials like stainless steel HSS‑E material for improved wear resistance Fully ground flutes for clean, accurate holes Conforms to DIN 338 for short twist drills Greater Stability and Consistent Hole Quality for Metalworking Short design reduces overhang and bending, giving the operator noticeably higher Stability during machining. This Twist Drill features a reduced overall length compared with standard variants, which minimizes vibration and improves concentricity. As a result, users benefit from more consistent hole diameters and less tool deflection when working on medium to hard metals. The shorter working length is particularly advantageous for precision setups and when using hand or bench Drilling Machines. Material Advantages that Extend Tool Life Manufactured from HSS‑E and alloyed with 5% cobalt, this drill combines hardness and heat resistance to withstand demanding drilling operations. The cobalt content increases red hardness, which helps maintain cutting edges at elevated temperatures and prolongs tool life when drilling alloyed and unalloyed Steels. The fully ground flute geometry ensures sharp cutting lips and smooth chip evacuation, producing cleaner holes and reducing the need for rework. Geometry Optimised for Hard Materials and Accuracy A 135° tip angle reduces the tendency to skate on hard surfaces and provides a better cutting approach for stainless steels and other tough materials. The Type N, or normal spiral, is the classic metalworking geometry that balances chip removal and cutting force. Ground (HSS‑G) versions like this produce very precise bores with excellent runout accuracy, making them suitable for applications where hole quality is critical. Application Scope and Machine Compatibility This Twist Drill is intended primarily for Drills for Metal and performs best in stationary or portable Drilling Machines with proper clamping and cooling. It is suitable for machining alloyed Steel, Cast Iron, Non‑Ferrous Metals and certain Plastics. For high feed or deep-hole work, users should evaluate appropriate coolant and machining parameters; for general metalworking tasks and short, precise bores the short HSS‑E Type N is an efficient choice. Who Benefits from This Tool Workshop professionals, maintenance technicians and precision fabricators who require repeatable, accurate bores will appreciate the combination of a short design, HSS‑E alloy and fully ground geometry. The drill is particularly useful when reduced runout and enhanced stiffness are required, such as in jigs, fixtures or handheld drilling where control and hole quality matter most. Strongly recommended: Choose the MetavCUT Twist Drill Type N short for demanding metalworking tasks and contact METAV Werkzeuge for expert advice and application support — eMail: info@metav-werkzeuge.com · Phone: +49 2822 7131930 · WhatsApp: +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 47069-FDA Diameter: 6.9 mm Tip angle: 135° Type: Type N Execution: short Colour / Alloy: 5% cobalt-alloyed Material: HSS-E Shaft finish: fully ground Spiral length: 69 mm Overall length: 109 mm Model series: Standard Line Standard: DIN 338 For machine: Drilling Machine Application: Drills for metal Packaging: 10 pieces Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials is the MetavCUT Twist Drill Type N suitable for? The MetavCUT Twist Drill Type N is primarily designed for metalworking and is suitable for alloyed and unalloyed Steel, Cast Iron, Non‑Ferrous Metals and certain Plastics; its HSS‑E composition and 135° tip make it particularly effective on harder materials. Is the short Twist Drill version better for precision work? A short Twist Drill by MetavCUT offers increased stiffness and reduced overhang, which leads to improved precision and less runout; this makes it a preferred option for accurate, repeatable holes in workshop and fixture applications. For what is a Twist Drill used? A Twist Drill is mainly applied when machining high‑strength materials and larger diameters; its shape allows for easier regrinding and it withstands higher loads, making it suitable for demanding metal drilling tasks. Which three drill types exist? The three main drill types are Metal Drill, Wood Drill and Stone/Concrete Drill; the MetavCUT Twist Drill belongs to the Metal Drill category and is optimised for metalworking. Why are Twist Drills sharpened at the tip? Tip sharpening reduces the chisel edge width at the drill point, lowering friction and required feed forces; by sharpening the tip of the MetavCUT Twist Drill Type N, the drill centres better and requires less thrust, improving accuracy. Can a metal Twist Drill be used to drill wood? A Metal Drill such as the MetavCUT Twist Drill can be used in wood, but guidance and finish are inferior compared with dedicated wood drills; metal drills are easier to regrind and show less self‑feeding tendency, which can be a drawback for clean wood holes.

Twist Drill — Type N, 6 mm, 135° tip, Short, 5% cobalt-alloyed, HSS‑E, DIN 338 A short Twist Drill (Type N) designed for precise metal drilling with Drilling Machines in workshop and maintenance applications. Short design for increased stability 6 mm diameter for standard metalwork 135° tip for hard materials HSS‑E with 5% cobalt boosts heat resistance Fully ground shank for high concentricity Greater precision through a short, stable design A short twist drill reduces overhang and therefore vibration, delivering noticeably improved positional accuracy when drilling metal. The reduced projection from the chuck increases stiffness and lowers the risk of wandering or bending, which is particularly beneficial when working with alloyed or hardened steels. The Type N spiral geometry, common for metalworking, ensures reliable chip evacuation and consistent hole quality even under frequent, repetitive use. Durability and heat resistance for demanding tasks Thanks to the HSS‑E material and a 5% cobalt alloying, this twist drill maintains hardness at elevated temperatures and resists thermal softening during continuous drilling. That makes it suitable for operations with higher cutting speeds or interruptive drilling where heat buildup is an issue. The fully ground flute geometry provides razor-sharp cutting edges and excellent concentricity, giving cleaner holes and longer service life when compared with rolled alternatives for precision work. Suited applications and best practice recommendations This Twist Drill (Type N) is optimized for drilling metal, including alloyed and unalloyed steels, cast iron, non‑ferrous metals and many technical plastics when used with appropriate feeds and cooling. The 135° tip angle reduces point pressure on hard materials and shortens pilot time, improving centring on tougher substrates such as stainless steel. For best results use a suitable cutting fluid and steady feed; the short length is ideal for handheld Drilling Machines and small machine tools. Who benefits most from this tool Workshops, maintenance technicians and professional metalworkers will value the mix of precision and robustness offered by this short, fully ground Twist Drill. Its design is particularly recommended where tight tolerances and repeatable hole quality are required. The DIN 338 specification ensures standardized dimensions and compatibility with common chucks and fixtures, making this drill a dependable choice for production and repair tasks. We recommend the MetavCUT Twist Drill (Type N) for precision metalworking — for expert guidance on suitability, reconditioning or application parameters please contact METAV Werkzeuge: 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 47060-FDA Type: Type N Diameter: 6 mm Tip angle: 135° Material: HSS‑E Alloy: 5% cobalt‑alloyed Execution: Short Overall length: 93 mm Spiral length: 57 mm Shank: Fully ground For drilling machine: Drilling Machine (Hand Drill) Standard: DIN 338 Series: Standard Line Application: Drills for metal Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Is the Twist Drill from MetavCUT suitable for stainless steel? The MetavCUT Twist Drill (Type N) is suited to stainless and other hard metals thanks to its HSS‑E composition and 135° tip, which together improve heat resistance and reduce workpiece hardening during drilling. Can the MetavCUT Twist Drill be resharpened? The MetavCUT Twist Drill with a fully ground geometry can be resharpened, but attention must be paid to preserve the original tip angle and chisel geometry to maintain the drill’s centring and cutting behaviour. What is a Twist Drill used for? A Twist Drill from MetavCUT is primarily applied to the machining of high‑strength materials and larger drill diameters. Its design is comparatively easy to resharpen and it withstands greater loads, making it suitable for demanding metalworking tasks. Which three drill types exist? Common drill types include metal drills, wood drills and stone/concrete drills; the MetavCUT Twist Drill belongs to the metal drill category and is optimized accordingly. Why are Twist Drills pointed? The pointing reduces the cross‑cut at the tip of the Twist Drill from MetavCUT, lowering friction and required feed forces, while improving centring of the tip in the workpiece. Can you drill wood with a Twist Drill? A metal Twist Drill such as the MetavCUT Type N can be used in wood, but guidance and finish are inferior compared with dedicated wood drills; however, they are simpler to resharpen and exhibit less self‑feeding tendency.

Twist Drill — Type N, 7.1 mm Ø, 135° tip, short design, 5% cobalt-alloyed, HSS‑E, DIN 338 A Twist Drill in a short execution designed for precise metal drilling in Drilling Machines. Short design for increased stability 7.1 mm diameter for precise hole making 135° tip angle for hard materials HSS‑E with 5% cobalt for heat resistance Fully ground shank for high runout accuracy Greater Precision and Reduced Deflection for Metalworking The Twist Drill short design minimises the exposed length outside the chuck, delivering noticeably higher stability and reduced tendency to bend during operation. This results directly in more accurate hole positions and cleaner hole edges when machining metal. For demanding tasks where positional accuracy matters, the shorter projection reduces chatter and improves repeatability on both hand-operated and machine setups, making this bit suited to precision assembly and component manufacture. Improved Cutting Performance in Tough Materials Manufactured from HSS‑E with 5% cobalt, this bit offers enhanced red hardness and wear resistance compared with standard HSS. The 135° tip angle is optimised for penetrating harder materials and reduces the initial cutting forces, which helps when working with stainless steel or other high-strength alloys. Type N spiral geometry provides a classic flute form that balances chip evacuation and surface finish, allowing longer runs under intermittent cooling without sacrificing hole quality. Conforms to DIN 338 for Reliable Machine Use Compliance with DIN 338 ensures the geometry and dimensions meet recognised industry norms for short twist drills. The design is intended for use in a Drilling Machine and is appropriate for drilling alloyed and unalloyed steel, cast iron, non‑ferrous metals and selected plastics. For users requiring standardised tooling that fits common holders and drilling setups, the adherence to this norm simplifies tool selection and inventory management. Workmanship, Shank Design and Practical Benefits A fully ground shank and precision flute grinding yield high concentricity and sharp cutting edges, which produce cleaner bores and reduce rework. The overall length of 109 mm with a spiral length of 69 mm keeps the tool compact while maintaining sufficient flute volume for chip removal. Supplied as part of the Standard Line series, this short twist drill is particularly well-suited to repetitive production tasks on stationary and portable drilling equipment where tool rigidity and hole quality are priorities. Strong recommendation: Choose MetavCUT’s Twist Drill Type N for robust, precise metal drilling — for technical advice or to confirm suitability for a specific task, METAV Werkzeuge offers expert consultation via eMail info@metav-werkzeuge.com, phone +49 2822 7131930 and WhatsApp +49 170 2837271 Technical Data Designation: Twist Drill Brand: MetavCUT SKU: 47071-FDA Diameter: 7.1 mm Tip angle: 135° Type: Type N Execution: short Colour: 5% cobalt-alloyed Material: HSS‑E Spiral length: 69 mm Overall length: 109 mm Shank execution: fully ground Model series: Standard Line Norm: DIN 338 For drilling machine: Drilling Machine Application: Drills for metal Manufacturer: MetavCUT Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What are Twist Drills used for? Twist Drills such as the MetavCUT Type N are primarily applied to the machining of high‑strength materials and larger drill diameters; their geometry is relatively easy to re‑grind and they withstand significant loads, making them suitable for demanding metal‑working tasks. Which three drill types exist? Common categories are metal drills, wood drills and stone/concrete drills; the MetavCUT Twist Drill belongs to the metal drill group and is optimised for ferrous and non‑ferrous materials. Why are Twist Drills tipped? Tipping reduces the cross‑cut at the point of the Twist Drill, which significantly lowers friction and the required feed force; this sharpening also improves centring of the tip in the workpiece for more accurate starts. Can a Twist Drill be used for wood? A metal Twist Drill like the MetavCUT Type N can be used in wood, but guidance and surface finish are typically inferior compared with dedicated wood drills; however, metal bits are easier to re‑grind and show less self‑feeding. At which drilling depths is the Twist Drill most commonly used? A through hole is typically executed with a Twist Drill; for diameters up to approx. 20 mm and depths up to 100 mm, the Twist Drill is the most frequently used tool for machining solid material. What is better, HSS or HSSE? The general assumption that HSSE is inherently superior to HSS is not universally true; selection should consider specific working conditions to determine whether the higher initial cost of HSSE (or HSS‑E) is justified for the application.

Spiralbohrer HSS‑E 7,2 mm, 135°, Typ N, 5% Kobaltlegiert, kurz, geschliffen, DIN 338, Standard Line von MetavCUT Der Spiralbohrer ist ein kurzer HSS‑E Metallbohrer für stabile und präzise Bohrungen in legierten und unlegierten Stählen sowie Nichteisenmetallen. Spiralbohrer HSS‑E, 7,2 mm für Metall Kurzbauweise für hohe Stabilität Geschliffen für exakten Rundlauf 135° Spitzenwinkel für harte Werkstoffe Typ N nach DIN 338 für Handbohrmaschine Mehr Präzision durch kurze Bauform Die Kurzbauweise reduziert die Auskraglänge und minimiert Vibrationen, was unmittelbar zu saubereren Bohrbildern führt. Für Anwender bedeutet das weniger Nacharbeit und eine höhere Trefferquote beim Bohren von Metall. Insbesondere bei Bohrungen in Stahl zahlt sich die höhere Stabilität des kurzen Spiralbohrers aus, weil Verkantungen seltener auftreten und die Standzeit des Werkzeugs steigt. Längerer Werkzeugstand durch Kobaltlegierung und HSS‑E Der Einsatz von HSS‑E mit 5% Kobalt erhöht die Warmfestigkeit gegenüber herkömmlichem Schnellarbeitsstahl und ermöglicht höhere Schnittgeschwindigkeiten bei Stahl. Die geschliffene Geometrie sorgt für sehr scharfe Schneiden und eine hohe Rundlaufgenauigkeit, wodurch saubere, maßhaltige Löcher entstehen. Für Anwender ohne tiefe Metallkenntnisse: HSS‑E steht für Schnellarbeitsstahl mit legiertem Kobalt, der die Hitzeverträglichkeit verbessert. Einsatzempfehlung für Werkstatt und Montage mit klarem Vorteil Mit einem Durchmesser von 7,2 mm befindet sich dieses Werkzeug im Standard‑Bereich und ist ideal für den Alltagsgebrauch in Werkstatt, Montage und beim Handwerk. Direktes Bohren ist möglich; bei sehr präzisen Passungen empfiehlt sich vorheriges Anpunkten mit einem Zentrierbohrer. Bei längeren Bohrungen oder harten Werkstoffen wird der Einsatz von Kühlschmierstoff empfohlen, um die Standzeit zu erhöhen. Für wen dieses Werkzeug entwickelt wurde und was es besonders macht Der Bohrer richtet sich an Fachbetriebe, ambitionierte Heimwerker und Montagebetriebe, die verlässliche Präzision bei Metallbohrungen erwarten. Die Kombination aus DIN 338‑Norm, geschliffener Zylinderschaft und 135°‑Spitzenwinkel macht das Werkzeug zur robusten Wahl für anspruchsvolle Anwendungen in Stahl und Guss sowie für Nichteisenmetalle. Wählen Sie die MetavCUT Standard Line und setzen Sie auf den präzisen HSS‑E Spiralbohrer 7,2 mm; bei Unsicherheit oder für zusätzliche technische Daten berät Sie METAV Werkzeuge gern per eMail info@metav-werkzeuge.com oder telefonisch +49 2822 7131930 Bezeichnung: Spiralbohrer Marke: MetavCUT SKU: 47072-FDA Durchmesser: 7,2 mm Material: HSS‑E Kobaltanteil: 5% kobaltlegiert Ausführung: kurz Schaft Ausführung: geschliffen Spitzenwinkel: 135° Typ: Typ N Norm: DIN 338 Gesamtlänge: 109 mm Spirallänge: 69 mm Für Bohrmaschine: Handbohrmaschine Modellserie: Standard Line Verpackungseinheit: 10 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Ist der Spiralbohrer von MetavCUT für Edelstahl geeignet? Der MetavCUT Spiralbohrer HSS‑E 7,2 mm mit 135° Spitzenwinkel eignet sich für härtere Werkstoffe; bei rostfreiem Edelstahl sollten reduzierte Schnittgeschwindigkeiten und Kühlschmierstoffe eingesetzt werden. Kann ich den geschliffenen Spiralbohrer mit einer Handbohrmaschine verwenden? Ja, der Spiralbohrer Typ N nach DIN 338 wurde für den Einsatz an Handbohrmaschinen und stationären Geräten entwickelt; die kurze Ausführung erhöht dabei die Stabilität bei manueller Führung. Warum ist die geschliffene Ausführung vorteilhaft gegenüber rollgewalzten Bohrern? Die geschliffene Geometrie des MetavCUT Spiralbohrers liefert schärfere Schneiden und höhere Rundlaufgenauigkeit, was präzisere Bohrlöcher in Metall ermöglicht; sie kann jedoch empfindlicher gegen Bruch sein und profitiert von stationärem Einsatz und Kühlung. Welche Vorteile bietet die 5% Kobaltlegierung bei diesem Bohrer? Die 5% Kobaltlegierung des HSS‑E Werkzeugs erhöht die Hitze‑ und Verschleißbeständigkeit, sodass der MetavCUT Spiralbohrer bei höheren Temperaturen stabiler arbeitet und längere Standzeiten in Stahl erreicht. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#47072-FDA","sku":"47072-FDA","mpn":"47072-FDA","gtin13":"","name":"Spiralbohrer 47072-FDA","description":"Spiralbohrer HSS‑E 7,2 mm, 135° Spitzenwinkel, Typ N, 5% Kobaltlegiert, kurz, geschliffen, DIN 338; Kurzbauweise für erhöhte Stabilität und präzise Metallbohrungen in legierten und unlegierten Stählen sowie Nichteisenmetallen.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-1200.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741e/logo-metav-1200-900.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png"],"author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Spiralbohrer HSS-E"},{"@type":"Thing","name":"Kurzbauweise für erhöhte Stabilität"},{"@type":"Thing","name":"DIN 338 Norm"}],"mentions":[{"@type":"Thing","name":"Geschliffener Zylinderschaft"},{"@type":"Thing","name":"5% Kobaltlegierung"},{"@type":"Thing","name":"Typ N - Normalspirale"}],"additionalProperty":[{"@type":"PropertyValue","name":"Bezeichnung","value":"Spiralbohrer"},{"@type":"PropertyValue","name":"Marke","value":"MetavCUT"},{"@type":"PropertyValue","name":"Durchmesser","value":"7,2 mm"},{"@type":"PropertyValue","name":"Material","value":"HSS‑E"},{"@type":"PropertyValue","name":"Kobaltanteil","value":"5% kobaltlegiert"},{"@type":"PropertyValue","name":"Ausführung","value":"kurz"},{"@type":"PropertyValue","name":"Schaft Ausführung","value":"geschliffen"},{"@type":"PropertyValue","name":"Spitzenwinkel","value":"135°"},{"@type":"PropertyValue","name":"Typ","value":"Typ N"},{"@type":"PropertyValue","name":"Norm","value":"DIN 338"},{"@type":"PropertyValue","name":"Gesamtlänge","value":"109 mm"},{"@type":"PropertyValue","name":"Spirallänge","value":"69 mm"},{"@type":"PropertyValue","name":"Für Bohrmaschine","value":"Handbohrmaschine"},{"@type":"PropertyValue","name":"Modellserie","value":"Standard Line"},{"@type":"PropertyValue","name":"Verpackungseinheit","value":"10"},{"@type":"PropertyValue","name":"Hersteller","value":"Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"Ist der Spiralbohrer von MetavCUT für Edelstahl geeignet?","acceptedAnswer":{"@type":"Answer","text":"Der MetavCUT Spiralbohrer HSS‑E 7,2 mm mit 135° Spitzenwinkel eignet sich für härtere Werkstoffe; bei rostfreiem Edelstahl sollten reduzierte Schnittgeschwindigkeiten und Kühlschmierstoffe eingesetzt werden."}},{"@type":"Question","name":"Kann der geschliffene Spiralbohrer mit einer Handbohrmaschine verwendet werden?","acceptedAnswer":{"@type":"Answer","text":"Ja, der Spiralbohrer Typ N nach DIN 338 wurde für den Einsatz an Handbohrmaschinen und stationären Geräten entwickelt; die kurze Ausführung erhöht dabei die Stabilität bei manueller Führung."}},{"@type":"Question","name":"Warum ist die geschliffene Ausführung vorteilhaft gegenüber rollgewalzten Bohrern?","acceptedAnswer":{"@type":"Answer","text":"Die geschliffene Geometrie des MetavCUT Spiralbohrers liefert schärfere Schneiden und höhere Rundlaufgenauigkeit, was präzisere Bohrlöcher in Metall ermöglicht; sie kann jedoch empfindlicher gegen Bruch sein und profitiert von stationärem Einsatz und Kühlung."}},{"@type":"Question","name":"Welche Vorteile bietet die 5% Kobaltlegierung bei diesem Bohrer?","acceptedAnswer":{"@type":"Answer","text":"Die 5% Kobaltlegierung des HSS‑E Werkzeugs erhöht die Hitze‑ und Verschleißbeständigkeit, sodass der MetavCUT Spiralbohrer bei höheren Temperaturen stabiler arbeitet und längere Standzeiten in Stahl erreicht."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/spiralbohrer-47072-FDA","dateModified":"2026-05-04T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Bohrer für Metall"},{"@type":"Thing","name":"Kurzbauweise für präzise Bohrungen"},{"@type":"Thing","name":"Geschliffener Zylinderschaft"}],"mentions":[{"@type":"Thing","name":"DIN 338"},{"@type":"Thing","name":"HSS‑E mit 5% Kobalt"},{"@type":"Thing","name":"Typ N - Normalspirale"}]}]}