HSS-E Spiralbohrer DIN 338 – Typ N, kurz, Co 5%, 135° Kreuzanschliff

Spiralbohrer — Twist Drill (Diameter 9.7 mm, 135° Tip, Type N, 5% Cobalt-Alloyed, Short, Fully Ground, DIN 338, HSS-E) — MetavCUT The Spiralbohrer Twist Drill is a short, fully ground metal-drilling tool designed for precise work in alloyed and unalloyed steels and other metals when used in a Drilling Machine Short design for increased stability and accuracy HSS-E with 5% cobalt for higher heat resistance 135° tip angle for improved centring in hard materials Fully ground flute geometry for precise, clean holes Conforms to DIN 338 for short twist drills Precision and Strength for Hard Materials The Twist Drill is made from HSS-E with 5% cobalt-alloyed composition, giving the tool improved heat resistance and edge stability when drilling metals. The 135° tip angle reduces walking on hard surfaces and supports cleaner hole entry, which is especially beneficial for stainless steel and other tough alloys. Type N (normal spiral) geometry means the flute helix and cutting angles are optimised for metalworking; this results in consistent chip evacuation and reliable cutting performance when used with appropriate Cutting Fluid. Short Length for Better Stability and Accuracy With a Diameter 9.7 mm, Spiral Length 87 mm and Overall Length 133 mm, the short execution minimises overhang from the chuck and therefore reduces deflection and vibration during drilling. Shorter projection increases rigidity, improving positional accuracy and lowering the risk of bend-induced runout. For fine or precision applications on metal components, the reduced cantilever effect helps achieve tighter tolerances and straighter bores. Fully Ground Finish and Practical Advantages The “geschliffen” or fully ground flute geometry produces sharp cutting edges and excellent concentricity. Compared with roll-formed alternatives, ground drills typically deliver finer surface finish and higher roundness in the hole, which is advantageous for assembly operations or when subsequent reaming/machining is planned. Users should note that ground drills can be more brittle than rolled variants and therefore benefit from controlled feed, correct spindle speeds and coolant during operation. Recommended Uses and Handling Tips Designed primarily for metalworking on stationary or portable machines, the Twist Drill excels in drilling alloyed and unalloyed steel, cast iron, non-ferrous metals and some plastics. For best results, clamp the work securely, select cutting speeds and feeds appropriate to HSS-E material, and apply coolant for heat-sensitive metals. The short Type N design makes this tool particularly suitable for precise maintenance, fabrication and production tasks where accuracy and durability are required. For demanding metal-drilling tasks, choose MetavCUT’s HSS-E Twist Drill for superior heat resistance and precision — METAV Werkzeuge offers expert advice and support by e‑mail at info@metav-werkzeuge.com, by phone at +49 2822 7131930 or via WhatsApp at +49 170 2837271 Twist Drill Brand: MetavCUT SKU: 47097-FDA Diameter: 9.7 mm Tip Angle: 135° Type: Type N Colour / Alloy: 5% cobalt-alloyed Execution: short Shaft Finish: fully ground Spiral Length: 87 mm Overall Length: 133 mm Material: HSS-E Standard: DIN 338 Application: Drills for metal Suitable For: Drilling Machine / Hand Drill Model Series: Standard Line Packaging Unit: 5 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill used for and where does the MetavCUT Spiralbohrer perform best? The MetavCUT Spiralbohrer Twist Drill is primarily used for machining high-strength materials and larger bore diameters; its geometry is easy to resharpen and it withstands higher loads, making it suitable for demanding metalworking tasks. Which three main drill types exist? The common drill categories are Metal Drills, Wood Drills and Masonry/Concrete Drills, and the MetavCUT Twist Drill belongs to the Metal Drill group tailored for metalworking applications.

Twist Drill — Short Type N, Ø 9.8 mm, 135°, HSS‑E, 5% cobalt‑alloyed, Fully Ground, DIN 338 The Twist Drill short Type N is a precision metal drilling bit for Drilling Machines, optimised for hard and alloyed metals with high heat resistance. Short design for increased stability and precision HSS‑E with 5% cobalt for higher heat resistance 135° point angle for hard metals and stainless steel Fully ground shank for sharp cutting and precise holes Conforms to DIN 338 for reliable industrial quality Durable Material for High‑Heat Metalworking and Longer Tool Life Thanks to its HSS‑E composition with 5% cobalt, this short Twist Drill delivers improved hardness and thermal stability compared with standard HSS. The cobalt‑alloyed steel retains cutting edge at elevated temperatures, reducing wear when drilling alloyed and unalloyed Steel, Cast Iron, Non‑Ferrous Metals and certain Plastics. This results in fewer tool changes and more consistent hole quality under demanding conditions. Short Geometry for Precision and Reduced Deflection The Short Design reduces the unsupported length outside the chuck, which significantly improves stability and minimises bending during cutting. Combined with the Fully Ground spiral geometry, the bit produces clean, accurate holes with excellent concentricity. The 135° Point Angle shortens the initial penetration time in harder materials and improves centring when machining stainless and other tough alloys. Built for Workshop and Industrial Metal Drilling Tasks Engineered according to DIN 338 and classified as Type N, this bit is intended for professional metalworking on Drilling Machines and stationary equipment. Typical applications include precision component fabrication and repair work where repeatable hole quality is required. For many workshop tasks the short configuration is preferred up to common diameter and depth ranges, offering dependable performance for production and maintenance environments. Practical Use Recommendations to Maximise Performance For best results, use appropriate cutting speeds and steady coolant to extend life and prevent overheating. The distinction between Ground and Rolled manufacturing matters: ground bits give sharper cutting edges and superior hole finish but can be less tolerant to shock; rolled bits are tougher but may sacrifice final surface quality. Secure clamping, correct speeds and feed rates, and lubrication ensure the best balance of lifetime and hole accuracy. Strongly recommend MetavCUT short Twist Drill for precision metalworking — for expert advice and to confirm suitability contact METAV Werkzeuge: 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp +49 170 2837271 Technical Data Twist Drill Brand: MetavCUT SKU: 47098-FDA Type: Type N Diameter: 9.8 mm Spiral length: 87 mm Overall length: 133 mm Point angle: 135° Material: HSS‑E Colour / Alloy: 5% cobalt-alloyed Shank finish: Fully ground Execution: Short Norm: DIN 338 Application: Drills for metal Model series: Standard Line Suitable for: Drilling Machine Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill Type N used for? The MetavCUT Twist Drill Type N is primarily used for machining high‑strength and harder metals where precision holes are required; its short design and HSS‑E material make it suitable for demanding metalwork and larger drilling diameters under controlled conditions. Which three drill types exist? The three main drill categories are Metal Drills, Wood Drills and Stone/Concrete Drills, each optimised in geometry and cutting angle for their respective materials. How does the MetavCUT Twist Drill Type N perform in high‑strength materials? The MetavCUT Twist Drill Type N is designed for high‑strength materials; its geometry and alloy content allow efficient cutting of tougher metals, and the form is easy to regrind while withstanding higher loads. Can metal Twist Drills be used for wood? A Metal Drill such as the MetavCUT Twist Drill can be used in Wood, but guidance and finish are typically inferior compared with dedicated Wood Drills; Metal Drills are easier to resharpen and have lower self‑feeding tendency.

Spiralbohrer kurz HSS-E 9,9 mm · 135° Spitzenwinkel · Typ N · 5% kobaltlegiert · geschliffen · DIN 338 · MetavCUT Der Spiralbohrer ist ein kurzer, geschliffener HSS-E Bohrer zur präzisen Bearbeitung von Metall und bietet hohe Stabilität bei stationären und handgeführten Anwendungen. Kurze Ausführung für verbesserte Stabilität Geschliffen für hohe Rundlaufgenauigkeit 5% kobaltlegiert für bessere Warmfestigkeit 135° Spitzenwinkel für harte Werkstoffe Spirallänge 87 mm bei Gesamtlänge 133 mm Hohe Stabilität und saubere Bohrbilder dank kurzer Bauform Die kurze Ausführung dieses Kurzbohrers reduziert die Auskraglänge und verringert dadurch das Risiko von Verbiegen und Ausschlagen. Durch die erhöhte Steifigkeit entsteht ein gleichmäßigeres Schnittbild und sauberere Bohrlöcher, was besonders bei Stahl und legierten Werkstoffen von Vorteil ist. Anwender profitieren von geringerer Nacharbeit und präziseren Passungen bei Serien- und Einzelteilen. Materialqualität und Schneidcharakteristik für anspruchsvolle Metallbearbeitung Der Bohrer besteht aus HSS-E mit 5% kobaltlegiertem Werkstoff, wodurch sich die Warmfestigkeit und Verschleißbeständigkeit gegenüber normalem Schnellarbeitsstahl verbessert. Die geschliffene Schaft- und Schneidgeometrie sorgt für scharfe Kanten und hohe Rundlaufgenauigkeit, eignet sich daher besonders für präzise Metallbohrungen. Der 135° Spitzenwinkel erleichtert den Anbohrvorgang in harten Stählen und reduziert das Abkippen beim Einschneiden. Vielseitige Einsatzbereiche im Werkstattalltag und bei Montagearbeiten Mit einem Durchmesser von 9,9 mm liegt der Bohrer im Standard-Bereich und ist ideal für Werkstatt, Montage und DIY-Projekte geeignet. Er bearbeitet legierten und unlegierten Stahl, Gusseisen, Nichteisenmetalle und Kunststoffe zuverlässig. Durch die Kombination aus DIN 338 Norm und Typ N Geometrie eignet sich der Bohrer für Handbohrmaschine ebenso wie für stationäre Säulenbohrmaschinen, solange auf passende Kühlschmierstoffe und korrekte Drehzahlen geachtet wird. Anwendungstipps zur Lebensdauer und Prozesssicherheit Vor dem Bohren empfiehlt sich das Anpunkten mit einem Zentrierbohrer zur Verbesserung der Positioniergenauigkeit; bei geschliffenen Bohrern sollte Kühlung eingesetzt werden, um Überhitzung zu vermeiden. Die Spirallänge 87 mm und die Gesamtlänge 133 mm geben Auskunft über Einspanntiefe und Handhabung; der Zylinderschaft erlaubt sicheren Halt im Bohrfutter. Regelmäßiges Entfernen von Spänen und moderate Vorschubgeschwindigkeiten verlängern die Standzeit. MetavCUT empfiehlt den Einsatz dieses geschliffenen HSS-E Kurzbohrers für präzise Metallbohrungen; bei Fragen zur Auswahl oder Anwendung steht METAV Werkzeuge mit technischer Beratung zur Seite – eMail: info@metav-werkzeuge.com, Telefon: +49 2822 7131930, WhatsApp: +49 170 2837271 Bezeichnung: Spiralbohrer kurz HSS-E 9,9 mm, Typ N, geschliffen Marke: MetavCUT SKU: 47099-FDA Durchmesser: 9,9 mm Spitzenwinkel: 135° Material: HSS-E Ausführung: kurz Schaft Ausführung: geschliffen Spirallänge: 87 mm Gesamtlänge: 133 mm Typ: Typ N Norm: DIN 338 Farbe: 5% kobaltlegiert Für Bohrmaschine: Handbohrmaschine Modellserie: Standard Line Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Welche Werkstoffe bearbeitet der Spiralbohrer von MetavCUT am besten? Der Spiralbohrer von MetavCUT mit HSS-E und 5% kobaltlegiert ist besonders geeignet für legierten und unlegierten Stahl, Gusseisen sowie Nichteisenmetalle und Kunststoffe; bei härteren Werkstoffen sorgt der 135° Spitzenwinkel für stabiles Anbohren. Eignet sich der Spiralbohrer von MetavCUT für die Handbohrmaschine? Ja, der Spiralbohrer von MetavCUT fällt in den Standard-Bereich und kann mit einer Handbohrmaschine verwendet werden; für beste Ergebnisse wird Anpunkten, kontrollierte Drehzahl und Kühlung empfohlen. Warum ist der Spiralbohrer geschliffen und was bedeutet das für den Anwender? Die geschliffene Ausführung des Spiralbohrers von MetavCUT liefert sehr scharfe Schneiden und hohe Rundlaufgenauigkeit, was präzise Bohrlöcher ermöglicht; gleichzeitig sollte auf passende Kühlung und stationäre Spannbedingungen geachtet werden, da geschliffene Bohrer empfindlicher gegenüber Verschleiß und Bruch sein können. Welche Vorteile bietet die 5% Kobaltlegierung beim Spiralbohrer von MetavCUT? Die 5% kobaltlegierte Zusammensetzung des Spiralbohrers von MetavCUT erhöht die Warmfestigkeit und Standzeit bei höheren Schnitttemperaturen, wodurch der Bohrer robuster bei der Bearbeitung von zähen oder legierten Stählen ist. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#47099-FDA","sku":"47099-FDA","mpn":"47099-FDA","name":"Spiralbohrer 47099-FDA","description":"Kurzer Spiralbohrer HSS-E 9,9 mm, 135° Spitzenwinkel, Typ N, 5% kobaltlegiert, geschliffen, DIN 338; Kurzbohrerausführung für präzise Metallbearbeitung mit hoher Stabilität und Rundlaufgenauigkeit.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741b/logo-metav-1200-1200.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741e/logo-metav-1200-900.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png"],"additionalProperty":[{"@type":"PropertyValue","name":"Bezeichnung","value":"Spiralbohrer kurz HSS-E 9,9 mm, Typ N, geschliffen"},{"@type":"PropertyValue","name":"Durchmesser","value":"9,9 mm"},{"@type":"PropertyValue","name":"Spitzenwinkel","value":"135°"},{"@type":"PropertyValue","name":"Typ","value":"Typ N"},{"@type":"PropertyValue","name":"Farbe","value":"5% kobaltlegiert"},{"@type":"PropertyValue","name":"Ausführung","value":"kurz"},{"@type":"PropertyValue","name":"Norm","value":"DIN 338"},{"@type":"PropertyValue","name":"Material","value":"HSS-E"},{"@type":"PropertyValue","name":"Schaft Ausführung","value":"geschliffen"},{"@type":"PropertyValue","name":"Spirallänge","value":"87 mm"},{"@type":"PropertyValue","name":"Gesamtlänge","value":"133 mm"},{"@type":"PropertyValue","name":"Für Bohrmaschine","value":"Handbohrmaschine"},{"@type":"PropertyValue","name":"Modellserie","value":"Standard Line"},{"@type":"PropertyValue","name":"Hersteller","value":"MetavCUT"}],"brand":null},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"Welche Werkstoffe bearbeitet der Spiralbohrer am besten?","acceptedAnswer":{"@type":"Answer","text":"Der Spiralbohrer kurz HSS-E 9,9 mm von MetavCUT mit 5% kobaltlegiert eignet sich besonders für legierten und unlegierten Stahl, Gusseisen, Nichteisenmetalle und Kunststoffe; der 135° Spitzenwinkel erleichtert das Anbohren härterer Werkstoffe."}},{"@type":"Question","name":"Eignet sich der Spiralbohrer für die Handbohrmaschine?","acceptedAnswer":{"@type":"Answer","text":"Ja, der Spiralbohrer kurz HSS-E 9,9 mm von MetavCUT ist für Handbohrmaschine geeignet; für beste Ergebnisse empfiehlt sich Anpunkten, kontrollierte Drehzahl und Kühlung."}},{"@type":"Question","name":"Was bedeutet geschliffen beim Spiralbohrer und welche Folgen hat das?","acceptedAnswer":{"@type":"Answer","text":"Geschliffen bedeutet, dass Spannuten und Geometrie per CNC geschliffen sind; das liefert sehr scharfe Schneiden und hohe Rundlaufgenauigkeit, erfordert aber Kühlung und schonende Handhabung, da geschliffene Bohrer spröder sein können."}},{"@type":"Question","name":"Welche Vorteile bringt die 5% Kobaltlegierung beim Spiralbohrer?","acceptedAnswer":{"@type":"Answer","text":"Die 5% kobaltlegiert Zusammensetzung erhöht die Warmfestigkeit und Standzeit bei höheren Schnitttemperaturen, wodurch der Spiralbohrer von MetavCUT robuster bei der Bearbeitung zäher oder legierter Stähle ist."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/47099-FDA","dateModified":"2026-05-04T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Spiralbohrer kurz HSS-E"},{"@type":"Thing","name":"DIN 338 Norm"},{"@type":"Thing","name":"MetavCUT Standard Line"}],"mentions":[{"@type":"Thing","name":"Geschliffene Schaftgeometrie"},{"@type":"Thing","name":"5% Kobaltlegierung"},{"@type":"Thing","name":"135° Spitzenwinkel für harte Werkstoffe"},{"@type":"Thing","name":"Zylinderschaft"}]}]}

Twist Drill – Short HSS‑E Type N, Ø 9 mm, 135°, 5% Cobalt‑Alloyed, DIN 338 (MetavCUT) The Twist Drill from MetavCUT is a short Type N drill for precise metalworking, especially suited to drilling hard and alloyed steels with a 135° tip angle. Short design for high stability 135° tip for hard materials Fully ground flutes for precise holes HSS‑E with 5% cobalt for heat resistance Conforms to DIN 338 for short drills Greater Precision through Short Design and Material Choice The short Execution reduces overhang and increases Stability, which is particularly beneficial when machining hard metals. Manufactured in HSS‑E with 5% Cobalt‑Alloyed composition, the tool offers improved heat resistance and wear behaviour compared with standard HSS. As a result, operators achieve cleaner holes and longer tool life when performing demanding Metalworking tasks on stationary or portable Drilling Machines. Clean Holes and High Runout Accuracy with Ground Geometry A Fully ground flute geometry produces very sharp cutting edges and excellent Runout Accuracy, ideal for precision applications. The Type N spiral geometry is the classic choice for Metal Drilling and generates reliable chip evacuation in many alloys. Note that ground drills can be more brittle than rolled variants, therefore using appropriate cooling and careful feed rates on tougher Materials is recommended to avoid breakage. Designed for Metalworking: Recommended Applications and Users This MetavCUT Twist Drill is intended for drilling Alloyed and Unalloyed Steel, Cast Iron, Non‑Ferrous Metals and certain Plastics; it is well suited to workshop technicians, maintenance teams and precision machinists. The short overall length and stable shank make it especially useful for operations requiring minimal deflection, such as jig and fixture work or when using a Hand Drill for controlled site repairs. 135° Point Angle: Faster Penetration and Better Centering in Hard Materials A 135° Point Angle helps reduce the tendency to wander on the surface of hard materials and shortens the initial penetration time compared with steeper points. This geometry lowers the cutting forces on the central tip and improves centring on Stainless Steel and other tough alloys, enabling more dependable starts and reducing the need for pilot operations in many cases. Standard Compliance and Practical Handling Notes Conforming to DIN 338 ensures consistent dimensions and interchangeability for short Twist Drills with cylindrical shank. The Standard Line manufacturing and the Fully Ground Shaft Execution ensure predictable performance across batches. For best results, pair the drill with appropriate coolant and moderate spindle speeds when working in high‑tensile steels; this preserves edge integrity and reduces the risk of chipping. Strong recommendation: choose the MetavCUT Twist Drill (Short Type N, HSS‑E) for demanding metal drilling tasks — for tailored advice or supplementary technical data contact METAV Werkzeuge by eMail: info@metav-werkzeuge.com, Tel: +49 2822 7131930, WhatsApp: +49 170 2837271 Technical Information Designation: Twist Drill Brand: MetavCUT SKU: 47090-FDA Diameter: 9 mm Point angle: 135° Type: Type N Execution: Short Colour: 5% cobalt-alloyed Material: HSS‑E Shaft execution: Fully ground Overall length: 125 mm Spiral length: 81 mm Model series: Standard Line Norm: DIN 338 For drilling machine: Drilling Machine (Hand Drill) Application: Drills for metal Packaging unit: 5 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What are Twist Drills used for? The MetavCUT Twist Drill (Type N) is primarily used for machining high‑strength materials and larger drill diameters; its geometry allows straightforward regrinding and it withstands greater mechanical loads, making it a standard choice for robust Metalworking tasks. Which three drill types exist? Common categories are Metal drills, Wood drills and Stone/Concrete drills, and the MetavCUT Twist Drill belongs to the Metal drill group suited for ferrous and non‑ferrous Materials. Can the MetavCUT Twist Drill be used for wood? The MetavCUT Twist Drill can be used in Wood, but as a Metal drill it offers less guidance and a rougher finish than dedicated Wood drills; it is easier to resharpen and shows lower self‑feeding tendency compared with specialised wood brad point drills.