HSS-G DIN 1897 Twist Drills – Type N, Extra Short, Bright, 135° Split Point

Twist Drill — 4.4 mm, 135°, Type N, extra short, Bright finished, HSS‑G, DIN 1897 The Twist Drill Type N is an extra‑short, high‑performance HSS‑G drill bit designed for precise metal drilling with hand Drilling Machines and in confined working spaces. Extra-short design for enhanced stability 4.4 mm diameter for precise holemaking 135° point for hard materials like stainless steel Cylindrical shank fits standard three-jaw chucks HSS-G material for increased wear resistance Greater control where space is limited The extra‑short construction reduces overhang and gives noticeably more stability during manual drilling, which lowers the risk of walking or breakage when working in narrow or thin components. This shortened geometry is especially advantageous when drilling into sheet metal, profiles or thin‑walled parts, since the reduced overall length makes the bit easier to guide and prevents unwanted bending under load. Faster drilling with less force A ground HSS‑G cutting geometry enables significantly improved cutting performance: users can expect up to 40% faster drilling while requiring roughly 50% less feed force compared with conventional HSS bits. This means reduced operator fatigue and more efficient machining cycles when producing holes in alloyed and unalloyed steel, cast materials, sintered iron and hard plastics. Engineered for demanding metalwork The 135° point angle is optimised for harder materials and short‑run accuracy: it reduces initial axial deflection and shortens the time to penetrate hard surfaces such as stainless steel. As a Type N normal‑spiral twist drill, the bit is primarily intended for metalworking applications and offers a well‑balanced flute geometry for reliable chip evacuation under typical workshop conditions. Practical fit and recommended use With a cylindrical shank, the bit fits universally in standard three‑jaw chucks, making it suitable for hand and angle Drilling Machines where convenience and universality matter. Professionals and advanced DIY users who require robust, short‑length drilling tools for maintenance, assembly or fabrication will find the bit particularly useful. If uncertain whether this tool meets specific requirements, METAV Werkzeuge offers competent technical advice and support via email, phone or WhatsApp. We recommend the MetavCUT Twist Drill for precision metalworking tasks — for tailored guidance or further technical details contact METAV Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 (WhatsApp +49 170 2837271) Designation: Twist Drill Brand: MetavCUT SKU: 56044-FDA Diameter: 4.4 mm Point angle: 135° Type: Type N Execution: extra short Finish: bright finished Shank: cylindrical Material: HSS-G Standard: DIN 1897 Spiral length: 22 mm Total length: 55 mm For Drilling Machine: Drilling Machine Application: Drills for metal Model series: Standard Line Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill used for and which workplaces suit the MetavCUT Twist Drill Type N? The MetavCUT Twist Drill Type N is primarily used for drilling metal; it is best applied in workshops and on assembly tasks where precise, stable holes are required. The extra‑short design makes this Twist Drill well suited to thin materials and confined spaces while the HSS‑G grade supports drilling in alloyed and unalloyed steels as well as cast materials. Which three drill types are common and how does the Twist Drill compare? Common drill types are metal drills, wood drills and stone/concrete drills. The MetavCUT Twist Drill (a metal drill) is optimised for metal applications and differs from wood or masonry drills in flute geometry, point angle and material, which together ensure cleaner holes and better durability when working with metals.

Twist Drill — Type N, 4.5 mm, 135°, Extra Short, Bright Finished, HSS‑G, DIN 1897 (Cylindrical Shank) by MetavCUT The Twist Drill Type N is an extra short HSS‑G drill designed for Drilling Machines and Hand Drills, offering high stability and efficient metalworking in tight or thin‑walled components. Extra‑short design for improved stability Optimised 135° tip for harder materials HSS‑G construction for long tool life Cylindrical shank fits standard chucks Standard Line quality for professional use Compact design increases stability and reduces breakage The Twist Drill in an extra short execution combines a reduced Overall Length with a shortened Spiral Length to deliver superior Verdrehungsfestigkeit (torsional stability) compared with standard drills. Shorter geometry reduces the lever arm and thus the risk of bending and breakage, which is especially valuable when working in constrained assemblies or on thin sheet and profile parts. The result is more reliable hole quality and fewer tool changes during demanding metalworking tasks. 135° point angle and Type N spiral for tougher materials A 135° tip halves the tendency to wander on tough surfaces and shortens the initial penetration phase, which is advantageous when machining stainless steel and other hard alloys. The Type N normal spiral profile is optimised for Metal work and provides consistent chip evacuation and cutting behaviour across legierte und unlegierte Stähle, Gusswerkstoffe and non‑ferrous metals. For operators this means cleaner entry holes and predictable feed forces when using a Hand Drill or Drilling Machine. Practical handling: cylindrical shank and compatibility Equipped with a Cylindrical Shank, this Twist Drill clamps securely in standard three‑jaw chucks and is universally compatible with conventional drill chucks. While cylindrical shanks are broadly adaptable, users should ensure correct chuck tightening to avoid slippage under high torque; using a torque‑controlled drill or a drill sleeve can further improve safety. The bright finished surface assists in visual inspection of wear and facilitates cleaning after use. Target users and best applications Developed for machinists, fitters and maintenance technicians, the MetavCUT Standard Line Twist Drill is particularly well suited to workshop tasks that require robust Metal drilling in tight spaces and accurate hole positioning. Conforming to DIN 1897 and made from HSS‑G, this tool balances cost and performance for professional everyday use and for jobs where straightforward regrindability and dependable cutting speed are required. For precision metalworking choose MetavCUT’s Twist Drill Type N with Extra Short design — METAV Werkzeuge offers comprehensive technical advice and personalised support: eMail info@metav-werkzeuge.com, Phone +49 2822 7131930, WhatsApp +49 170 2837271 Technical data Designation: Twist Drill Brand / Manufacturer: MetavCUT SKU: 56045-FDA Diameter: 4.5 mm Point Angle: 135° Execution: Extra short Finish / Colour: Bright finished Material: HSS‑G Type: Type N Spiral Length: 24 mm Total Length: 58 mm Shank Execution: Cylindrical For Drilling Machine: Drilling Machine (Hand Drill) Model Series: Standard Line Application: Drills for Metal Standard: DIN 1897 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Is the Twist Drill Type N from MetavCUT suitable for hand drills? Yes. The MetavCUT Twist Drill Type N with a Cylindrical Shank is designed for use in Hand Drills and standard chucks; its Extra Short geometry improves stability in manual operations and reduces the risk of breakage when clamping and feeding correctly. What is the Twist Drill used for? The Twist Drill Type N by MetavCUT is primarily applied to the machining of high‑strength materials and larger hole diameters; its form is straightforward to regrind and withstands higher loads, making it ideal for steels, cast materials and hard plastics. Which three drill types exist? Common categories are Metal drills (such as the MetavCUT Twist Drill Type N), Wood drills, and Stone/Concrete drills. Why are Twist Drills pointed? Twist Drills are pointed to reduce the cross‑cut at the tip; this lowering of the cross‑edge decreases friction so that significantly lower feed forces are required and the drill centers more reliably in the workpiece. Can a metal drill be used in wood? A Metal drill such as the MetavCUT Twist Drill can be used in Wood, but guidance and finish may be inferior compared with dedicated Wood drills; however, metal drills are easier to regrind and tend to produce less self‑feeding. For which drilling depths is the Twist Drill most commonly used? A through‑hole in solid material is typically executed with a Twist Drill; for diameters up to 20 mm and drilling depths up to 100 mm the Twist Drill is the most commonly used tool. Is HSS or HSSE better? There is no universal answer; the belief that HSSE steels are always superior to HSS is incorrect. Assess whether your working conditions justify the higher cost of HSSE before choosing.

Twist Drill — Type N extra short, 4.6 mm, 135°, Bright Finished, HSS‑G, DIN 1897 (MetavCUT) The Twist Drill is an extra short HSS‑G metal drill (Type N) designed for precise drilling in hard and alloyed steels with handheld Drilling Machines. Extra-short design for improved stability HSS‑G ground for faster, lower-force drilling 135° point angle for harder materials Cylindrical shank fits standard three-jaw chucks Conforms to DIN 1897 for industrial robustness Short form, big gains for stability and tight spaces Thanks to its Extra Short construction, this Twist Drill reduces bending and vibration during operation, which leads to fewer breakages and cleaner holes when working in confined or thin-walled components. The shortened Overall Length and reduced Spiral/Working Length make it particularly suitable for drilling in panels, profiles and assemblies where access is limited. Users benefit from improved tool life and safer handling, especially when exchanging bits frequently in workshop or maintenance environments. Faster, lower-effort metal drilling with optimised geometry The combination of HSS‑G material and a ground flute geometry enables up to 40% quicker drilling with about 50% less axial force compared with conventional HSS bits, according to the product data. A 135° Point Angle is chosen specifically for tougher substrates such as stainless and alloy steels; this angle reduces initial skidding and helps the bit cut more efficiently into hard materials. As a Type N (normal spiral) bit, it provides reliable chip evacuation for metalworking tasks while maintaining versatility across a range of ferrous and non‑ferrous metals. Simple fitting and dependable compatibility on common drills Equipped with a Cylindrical Shank, the Twist Drill is compatible with standard three‑jaw chucks found on most Hand Drilling Machines, making it easy to clamp and use without special adaptors. The design trade‑off is well known: universal fitting versus potential slipping under very high torque; correct chuck tightening and appropriate drilling speeds avoid this. Conformance to DIN 1897 ensures consistent dimensions and performance, supporting predictable results in professional workflows. Who gets the most from this bit and why it stands out Workshops, fabricators and field technicians benefit most from the MetavCUT extra short Twist Drill when precise, repeatable metal holes are required in restricted spaces. The bit’s robust construction addresses high demands in materials like cast iron, tempered steel and hard plastics used in industrial applications. Its Standard Line model series balances durability and economy, offering a reliable option for repair, maintenance and production tasks where controlled drilling behaviour matters. MetavCUT recommends this Twist Drill Type N for demanding metalworking tasks; for tailored advice or additional technical data, contact METAV Werkzeuge — eMail: info@metav-werkzeuge.com — Tel: +49 2822 7131930 — WhatsApp: +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 56046-FDA Diameter: 4.6 mm Point angle: 135° Type: Type N Finish: Bright finished Execution: Extra short Material: HSS‑G Spiral length: 24 mm Overall length: 58 mm Shank execution: Cylindrical Suitable for: Drilling Machine (Hand Drilling Machine) Model series: Standard Line Applications: Drills for metal Norm: DIN 1897 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Can the MetavCUT Twist Drill Type N be used in a handheld drill? Yes, the MetavCUT Twist Drill Type N is intended for use with Hand Drilling Machines; its Cylindrical Shank fits standard three‑jaw chucks and allows quick mounting for on-site and workshop tasks while ensuring stable operation when the chuck is properly tightened. Is the Twist Drill suitable for stainless steel and other hard metals? The Twist Drill from MetavCUT, made of HSS‑G with a 135° Point Angle, is particularly suited to harder materials such as stainless and alloyed steels; the geometry and material reduce skidding and support efficient cutting in demanding metalworking applications. What is a Twist Drill used for? A Twist Drill is mainly applied to the machining of high‑strength materials and large drill diameters. This form is easy to resharpen and resists higher loads. The bit’s design suits drilling in alloyed and unalloyed steel, cast steel, cast iron, sintered iron, malleable iron, non‑ferrous metals and hard plastics. Which 3 drill types are there? There are three common drill types: Metal drills, Wood drills, and Stone/Concrete drills.

Twist Drill — Type N extra short, 4.7 mm, 135° point, HSS‑G, bright finished (DIN 1897) The Twist Drill Type N from MetavCUT is an extra‑short HSS‑G drill bit for Drilling Machines, designed for precise metalworking in confined spaces. Extra‑short HSS‑G design for tight working spaces 135° point angle for drilling hard materials Cylindrical shank fits standard three‑jaw chucks Up to 40% faster drilling, 50% less feed force Faster, stronger performance for metalworking The extra‑short geometry of this Twist Drill increases stability and reduces the risk of breakage when working in restricted areas. The ground HSS‑G cutting edges allow for up to 40% faster penetration and require 50% less feed force compared with conventional HSS bits, which translates into less operator fatigue and higher throughput in repetitive metal drilling tasks. This makes the bit particularly effective for alloyed and unalloyed steel, cast materials and hard plastics. Reliable centring and compatibility with common chucks With a 135° point angle, the bit is optimised for harder workpiece materials and short lead‑in times. The cylindrical shank provides universal compatibility with standard three‑jaw chucks on a handheld Drilling Machine, ensuring quick tool changes and secure clamping in everyday workshop environments. For applications where torque is especially high, consider the shank type when selecting the correct chuck to avoid slippage. Practical use cases and who benefits most This Twist Drill is ideal for professionals and workshops that perform frequent small‑diameter metal drilling in thin sheet, profiles and component assemblies. Its compact length is particularly useful for tight fixture setups, angle drilling and operations near edges where a standard length would be impractical. Toolrooms, maintenance teams and metal fabricators will value the improved control and reduced breakage rate. What sets this drill apart: standards and material Manufactured to DIN 1897 specifications and produced in HSS‑G material, the bit balances wear resistance and re‑sharpenability. The bright finished surface facilitates chip evacuation while the Type N spiral is the established choice for general metal drilling. For users less familiar with technical terms: HSS‑G denotes a high‑speed steel with improved cutting properties for demanding metallic materials. Strong recommendation: Choose the MetavCUT Twist Drill Type N for precision metal drilling and contact METAV Werkzeuge for personalised technical advice via info@metav-werkzeuge.com or +49 2822 7131930 (WhatsApp +49 170 2837271) Twist Drill Marke: MetavCUT SKU: 56047-FDA Durchmesser: 4.7 mm Gesamtlänge: 58 mm Spiralänge: 24 mm Ausführung: extra short Spitzenwinkel: 135° Typ: Type N Schaftausführung: Cylindrical Material: HSS‑G Norm: DIN 1897 Farbe / Finish: Bright finished Für Bohrmaschine: Drilling Machine (Hand drill) Modellserie: Standard Line Anwendung: Drills for metal Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What applications is the MetavCUT Twist Drill Type N best suited for? The MetavCUT Twist Drill Type N is primarily intended for metal drilling, including alloyed and unalloyed steel, cast iron and hard plastics; its extra‑short form makes it especially useful when working in confined spaces or on thin materials. Can the MetavCUT Twist Drill be used in a handheld drill? Yes, the Twist Drill from MetavCUT with a cylindrical shank is made to be clamped in standard three‑jaw chucks of a handheld Drilling Machine; ensure appropriate chuck grip when high torque is applied to prevent slippage. What is a Twist Drill used for? A Twist Drill is mainly used for machining high‑strength materials and larger drill diameters. Its shape allows for straightforward re‑grinding and it withstands substantial loads, making it suitable for demanding metalworking operations. Which three drill types exist? There are three common drill categories: metal drills, wood drills and stone/concrete drills. Why are Twist Drills re‑pointed? Re‑pointing reduces the minor cutting edge at the tip, lowering friction and required feed force while improving centring of the bit in the workpiece. Can a metal Twist Drill be used for wood? A metal Twist Drill can be used in wood, but guidance and finish are generally inferior compared with dedicated wood drills; metal bits are easier to re‑sharpen and show less self‑feed.

Spiralbohrer HSS‑G Ø 4,8 mm, 135° Spitzenwinkel, Typ N, blank, extra kurz, DIN 1897 Der Spiralbohrer HSS‑G in extra kurz Ausführung ist für präzise Metallbohrungen mit der Handbohrmaschine konzipiert und bietet hohe Stabilität bei engen Platzverhältnissen. Spiralbohrer HSS‑G Ø 4,8 mm extra kurz 135° Spitzenwinkel für harte Werkstoffe Zylinderschaft für gängige Bohrfutter Spirallänge 24 mm für sauberen Spanabtransport Extra kurz: höhere Stabilität, geringere Bruchneigung Mehr Stabilität bei beengten Platzverhältnissen dank kurzer Bauweise Die extra kurz Ausführung reduziert die Hebelwirkung und erhöht dadurch die Verdrehungsfestigkeit beim Bohren in dünnem Material oder an schwer zugänglichen Stellen. Durch die kompakte Gesamtlänge von 58 mm und die Spirallänge 24 mm verringert sich die Bruchneigung deutlich, was die Ausfallzeiten in der Werkstatt reduziert. Zusätzlich ermöglicht die geschliffene Schneide ein bis zu 40 % schnelleres Bohren bei gleichzeitig 50 % geringerem Anpressdruck, was Ergonomie und Effizienz verbessert. Gezielte Materialbearbeitung durch Spitzenwinkel und Typauswahl Der 135° Spitzenwinkel macht dieses Werkzeug besonders geeignet für harte und zähe Werkstoffe wie Edelstahl oder gehärtete Stähle, weil die Anbohrzeit verkürzt und das Wandern beim Ansetzen reduziert wird. Als Typ N mit Normalspirale ist der Bohrer optimal auf die Bearbeitung von legiertem und unlegiertem Stahl, Gusseisen sowie Nichteisenmetallen abgestimmt. Für Anwender ohne tiefes Fachwissen: Der Spitzenwinkel beschreibt den Winkel an der Bohrerspitze und beeinflusst das Eindringverhalten und die Spanbildung. Universelle Handhabung und Hinweise zur Einsatzsicherheit Der glatte Zylinderschaft macht das Werkzeug kompatibel mit nahezu allen Dreibackenfuttern und ermöglicht schnelles Wechseln in der Handbohrmaschine. Die Standardnorm DIN 1897 signalisiert definierte Abmessungen und eine bewährte Herstellungsqualität. Bei hohen Drehmomentanforderungen sollte auf ein kraftschlüssiges Spannsystem geachtet werden, da ein Zylinderschaft unter extremen Lasten zum Durchrutschen neigen kann. Einsatzgebiete und Zielgruppe für zuverlässige Alltagslösungen Mit einem Durchmesser Ø 4,8 mm gehört der Bohrer in den Standard‑Bereich und eignet sich ideal für Werkstatt, Montage und DIY‑Projekte; typische Anwendungsfelder sind Bleche, Profile und mittlere Flachstähle. Die kompakte Länge macht ihn zur ersten Wahl bei Bohrungen in dünnwandigen Bauteilen oder an schwer zugänglichen Ausbaukonstruktionen. Fachhandwerker und ambitionierte Heimwerker profitieren gleichermaßen von der Kombination aus Stabilität und universeller Einsetzbarkeit. Empfehlung: MetavCUT HSS‑G Spiralbohrer in extra kurz Ausführung wählen für präzise Metallbohrungen mit der Handbohrmaschine; bei Unsicherheiten oder für individuelle Beratung steht METAV Werkzeuge gern per eMail unter info@metav-werkzeuge.com oder telefonisch unter +49 2822 7131930 zur Verfügung Technische Daten Bezeichnung: Spiralbohrer Marke: MetavCUT SKU: 56048-FDA Material: HSS-G Durchmesser: 4,8 mm Spitzenwinkel: 135° Typ: Typ N Ausführung: extra kurz Norm: DIN 1897 Farbe: blank Schaftausführung: Zylinder Gesamtlänge: 58 mm Spirallänge: 24 mm Für Bohrmaschine: Handbohrmaschine Modellserie: Standard Line Verpackungseinheit: 10 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Was bedeutet die Bezeichnung extra kurz beim Spiralbohrer von MetavCUT? Die Bezeichnung extra kurz beim Spiralbohrer von MetavCUT beschreibt eine verkürzte Gesamtlänge und reduzierte Arbeitslänge, wodurch Stabilität und Widerstandsfähigkeit beim Bohren in engen Bereichen verbessert werden. Für welche Materialien eignet sich der MetavCUT Spiralbohrer HSS‑G Typ N am besten? Der MetavCUT Spiralbohrer HSS‑G Typ N eignet sich besonders für legierte und unlegierte Stähle, Gusseisen sowie Nichteisenmetalle; die Normalspirale ist speziell für Metallbearbeitung ausgelegt. Kann der Spiralbohrer MetavCUT Ø 4,8 mm in jeder Handbohrmaschine verwendet werden? Ja, der Spiralbohrer MetavCUT mit Zylinderschaft ist für gängige Dreibackenfutter konzipiert, wobei bei sehr hohem Drehmoment ein kraftschlüssiges Spannsystem empfohlen wird. Wie beeinflusst der 135° Spitzenwinkel die Bohrleistung des MetavCUT Spiralbohrers? Der 135° Spitzenwinkel beim MetavCUT Spiralbohrer reduziert das Wandern beim Ansetzen und erleichtert das Anbohren harter Werkstoffe, wodurch präzisere Bohrlöcher erzielt werden. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#56048-FDA","sku":"56048-FDA","mpn":"56048-FDA","name":"Spiralbohrer 56048-FDA","description":"Spiralbohrer HSS-G Ø 4,8 mm, 135° Spitzenwinkel, Typ N, blank, extra kurz nach DIN 1897; extra kurze Bauweise für hohe Stabilität bei handgeführten Bohrungen in dünnen und schwer zugänglichen Werkstücken; geeignet für legierte und unlegierte Stähle, Gusseisen und Nichteisenmetalle.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741b/logo-metav-1200-1200.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741e/logo-metav-1200-900.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png"],"additionalProperty":[{"@type":"PropertyValue","name":"Bezeichnung","value":"Spiralbohrer"},{"@type":"PropertyValue","name":"Marke","value":"MetavCUT"},{"@type":"PropertyValue","name":"SKU","value":"56048-FDA"},{"@type":"PropertyValue","name":"Material","value":"HSS-G"},{"@type":"PropertyValue","name":"Durchmesser","value":"4,8 mm"},{"@type":"PropertyValue","name":"Spitzenwinkel","value":"135°"},{"@type":"PropertyValue","name":"Typ","value":"Typ N"},{"@type":"PropertyValue","name":"Ausführung","value":"extra kurz"},{"@type":"PropertyValue","name":"Norm","value":"DIN 1897"},{"@type":"PropertyValue","name":"Farbe","value":"blank"},{"@type":"PropertyValue","name":"Schaftausführung","value":"Zylinder"},{"@type":"PropertyValue","name":"Gesamtlänge","value":"58 mm"},{"@type":"PropertyValue","name":"Spirallänge","value":"24 mm"},{"@type":"PropertyValue","name":"Für Bohrmaschine","value":"Handbohrmaschine"},{"@type":"PropertyValue","name":"Modellserie","value":"Standard Line"},{"@type":"PropertyValue","name":"Verpackungseinheit","value":"10"},{"@type":"PropertyValue","name":"Generelle Anwendung","value":"Bohrer für Metall"},{"@type":"PropertyValue","name":"Hersteller","value":"Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"Was bedeutet die Bezeichnung Extra kurz beim Spiralbohrer von MetavCUT?","acceptedAnswer":{"@type":"Answer","text":"Die Bezeichnung Extra kurz beim Spiralbohrer MetavCUT beschreibt eine verkürzte Gesamtlänge und reduzierte Arbeitslänge, wodurch Stabilität und Verdrehungsfestigkeit beim Bohren in engen Bereichen erhöht und die Bruchneigung reduziert werden."}},{"@type":"Question","name":"Für welche Materialien eignet sich der MetavCUT Spiralbohrer HSS-G Typ N am besten?","acceptedAnswer":{"@type":"Answer","text":"Der MetavCUT Spiralbohrer HSS-G Typ N eignet sich besonders für legierte und unlegierte Stähle, Gusseisen sowie Nichteisenmetalle und ist damit ideal für Metallbohrungen mit der Handbohrmaschine."}},{"@type":"Question","name":"Kann der Spiralbohrer MetavCUT Ø 4,8 mm in jeder Handbohrmaschine verwendet werden?","acceptedAnswer":{"@type":"Answer","text":"Ja, der Spiralbohrer MetavCUT Ø 4,8 mm verfügt über einen Zylinderschaft und ist für gängige Dreibackenfutter konzipiert; bei sehr hohem Drehmoment empfiehlt sich ein kraftschlüssiges Spannsystem, um Durchrutschen zu vermeiden."}},{"@type":"Question","name":"Wie beeinflusst der 135° Spitzenwinkel die Bohrleistung des MetavCUT Spiralbohrers?","acceptedAnswer":{"@type":"Answer","text":"Der 135° Spitzenwinkel des MetavCUT Spiralbohrers reduziert das Wandern beim Ansetzen und erleichtert das Anbohren harter Werkstoffe wie Edelstahl, was präzisere Bohrlöcher und kürzere Anbohrzeiten zur Folge hat."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/spiralbohrer-56048-FDA","dateModified":"2026-05-04T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Spiralbohrer HSS-G extra kurz"},{"@type":"Thing","name":"MetavCUT Standard Line"},{"@type":"Thing","name":"Bohrer für Metall"}],"mentions":[{"@type":"Thing","name":"Zylinderschaft für Dreibackenfutter"},{"@type":"Thing","name":"DIN 1897 normiert"},{"@type":"Thing","name":"135° Spitzenwinkel für harte Werkstoffe"},{"@type":"Thing","name":"Spirallänge 24 mm für Spanabtransport"}]}]}

Twist Drill (Type N) — Extra Short, 4.9 mm, 135° Point, HSS‑G, Bright Finished, DIN 1897 — MetavCUT A Twist Drill (Type N) for metalworking, engineered as an extra short HSS‑G bit for use in hand and drilling machines. Extra short HSS‑G design for greater stability 135° tip for harder materials and fast entry Cylindrical shank for universal chuck compatibility 4.9 mm diameter with 24 mm spiral length for metalwork Complies with DIN 1897 for robust hand‑drill applications Greater efficiency and durability for metal drilling The extra short design delivers improved rigidity and reduced breakage risk when working with metal. Manufactured from HSS‑G, this bit allows up to 40% faster drilling while requiring 50% less feed force compared with conventional HSS variants, making it particularly efficient for alloyed and unalloyed steel, cast steel, gray cast iron, sintered iron, malleable cast iron, non‑ferrous metals and hard plastics. The compact geometry is especially advantageous when drilling thin sections or in confined spaces where conventional lengths are impractical. Reliable performance in tight spaces and portable setups Designed to DIN 1897 as an extra short Twist Drill, the shortened Overall Length and reduced Working Length increase torsional resistance and decrease vibration. The cylindrical shank fits standard three‑jaw chucks, offering universal compatibility with hand and angle drills while improving concentricity. This construction supports steady drilling under manual guidance and reduces the chance of chatter when accessing narrow profiles or sheet metal. Precision entry and material suitability explained Equipped with a 135° Point Angle, the Type N spiral geometry is tuned for harder workpiece materials, shortening the initial cutting time and improving centering on tougher alloys. With a nominal Diameter of 4.9 mm, a Spiral Length of 24 mm and an Overall Length of 58 mm, the bit provides a balanced ratio between cutting depth and structural stiffness. The Normal Spiral (Type N) is the classic metal‑drilling profile and is not optimized for very soft materials. Handling, maintenance and practical tips for long life Periodic resharpening restores cutting geometry and maintains the reduced thrust advantage of the pointed tip; the ground HSS‑G material is regrindable and holds its edge under demanding loads. Appropriate cutting fluids extend tool life when machining steels and cast materials. To avoid slippage in a cylindrical shank, ensure secure clamping in the chuck and apply controlled feed; for high torque applications a three‑flat or hex shank could be preferred, but the cylindrical shaft here offers broad flexibility for general metalworking tasks. Strong recommendation: For reliable metal drilling in constrained or manual setups, choose the MetavCUT Twist Drill Type N in extra short HSS‑G; for further technical guidance or project advice contact METAV Werkzeuge by eMail info@metav-werkzeuge.com, by phone +49 2822 7131930 or via WhatsApp +49 170 2837271 Twist Drill Brand: MetavCUT SKU: 56049-FDA Diameter: 4.9 mm Point Angle: 135° Type: Type N Finish: Bright finished Execution: Extra short Material: HSS-G Standard: DIN 1897 Shank Execution: Cylindrical Spiral Length: 24 mm Overall Length: 58 mm For Drilling Machine: Hand/Drilling Machine Model Series: Standard Line Application: Drills for Metal Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Can the MetavCUT Twist Drill Type N be used in a cordless hand drill? The MetavCUT Twist Drill Type N is suitable for use in hand drills and portable drilling machines when clamped securely in a proper chuck. The extra short length enhances stability under manual operation, but correct chuck tightening and appropriate feed are essential to prevent slippage of the cylindrical shank. Is the MetavCUT Twist Drill Type N suitable for stainless and hardened steels? The MetavCUT Twist Drill Type N with a 135° tip is designed for harder workpiece materials and offers improved entry and centering on tougher steels; use suitable cutting fluid and moderate speeds for optimal life and hole quality. For what are Twist Drills used? Twist Drills are mainly applied to the machining of high‑strength materials and larger hole diameters. Their form is easy to regrind and withstands higher loads, making them the standard choice for metal drilling tasks where robustness and serviceability are required. Which 3 drill types are there? The three common drill categories are metal drills, wood drills and stone/concrete drills. The MetavCUT Twist Drill Type N belongs to the metal drill group and is optimized for ferrous and many non‑ferrous materials.

MetavCUT Twist Drill — 4 mm, 135° Tip, Type N, Bright Finished, Extra Short, DIN 1897, HSS‑G The MetavCUT Twist Drill is an extra short Type N drill bit designed for precise metalworking with Drilling Machines and Hand Drills, offering stable performance in confined spaces. Extra short design for greater stability 135° tip angle for harder materials Cylindrical shank for universal chuck fitting Made from HSS‑G for durable, fast drilling Conforms to DIN 1897 for consistent dimensions High Stability and Faster Penetration for Metalworking The extra short geometry of this Twist Drill reduces overall length and cutting length, which increases stability and reduces the risk of breakage when working in tight or thin components. The ground HSS‑G cutting edges enable up to 40% faster drilling with approximately 50% less axial force compared with conventional HSS drills, so operators can achieve cleaner holes with less exertion. This makes the bit particularly suitable for repetitive metalworking tasks where tool life and operator comfort matter. Secure Cutting in Tough Materials Thanks to 135° Tip A 135° tip angle tailors the MetavCUT Twist Drill to harder workpiece materials such as alloyed and unalloyed steels, cast steels and other dense metals. The blunter tip reduces initial cutting forces and shortens the time to penetrate the surface, improving centering and reducing walking on stainless steel or tempered iron. For customers less familiar with geometry: a larger tip angle spreads the contact area and delays dulling, which keeps hole quality consistent over longer runs. Universal Compatibility with Cylindrical Shank and Standard Norms Equipped with a cylindrical (round) shank, the Twist Drill clamps easily in standard three‑jaw chucks of Hand Drills and Drilling Machines, delivering a simple and universal fit. Conformity to DIN 1897 ensures predictable overall and flute lengths for tool planning and replacement. Note that while the round shank is widely compatible, under very high torque conditions a chuck may allow slight slippage compared with polygonal shanks. Practical Use Cases and Who Benefits Most This Twist Drill is aimed at professionals and well‑equipped hobbyists who work with metal, such as fabricators, maintenance technicians and toolroom operators. It excels in drilling into sheet metal, profiles, castings and harder grades of steel where short overhang and robust performance are required. For thin‑walled components or cramped setups the extra short format improves control and reduces chatter, producing cleaner bores with less rework. Handling Tips and Best Practices When using the MetavCUT Twist Drill, apply moderate cutting speeds suited to HSS‑G in metals and use cutting fluid where applicable to extend tool life and improve finish. A light pilot or centre punch helps to prevent walking on smooth surfaces. Because the bit is extra short, avoid excessive overhang from the chuck—keep the working length as short as practical to retain the stability advantages. For demanding professional metalwork choose the MetavCUT Twist Drill for reliable, high‑performance results — METAV Werkzeuge offers expert advice and technical support at info@metav-werkzeuge.com, by telephone on +49 2822 7131930 or via WhatsApp at +49 170 2837271 Twist Drill Marke: MetavCUT SKU: 56040-FDA Diameter: 4 mm Tip angle: 135° Type: Type N Colour: Bright finished Execution: Extra short Material: HSS‑G Shaft execution: Cylindrical Spiral length: 22 mm Overall length: 55 mm Suitable for: Drilling Machine / Hand Drill Model series: Standard Line Application: Drills for metal Norm: DIN 1897 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials is the MetavCUT Twist Drill suitable for? The MetavCUT Twist Drill is designed primarily for metalworking and performs well in alloyed and unalloyed steel, cast steel, cast iron, sintered iron, non‑ferrous metals and hard plastics; its HSS‑G composition and Type N spiral make it a reliable choice for tougher materials. How should the MetavCUT Twist Drill be used to avoid breakage? Use the MetavCUT Twist Drill with minimal overhang, appropriate cutting speeds for HSS‑G, and cutting fluid where recommended; a centre punch for starting and moderate feed rates help maintain hole quality and reduce the risk of breakage. What is a Twist Drill used for? A Twist Drill, such as the MetavCUT Twist Drill, is primarily applied to machining high‑strength materials and larger hole diameters; its form is easy to regrind and it withstands high loads, making it suitable for demanding metal drilling tasks. Which 3 drill types are there? The three principal drill categories are metal drills (like the MetavCUT Twist Drill), wood drills, and stone/concrete drills.

Twist Drill — HSS‑G Extra Short, Ø 5.1 mm, 135° Point Angle, Type N (Bright Finished, Cylindrical Shank, DIN 1897) by MetavCUT The Twist Drill is an extra short Type N metal drill designed for Hand Drilling Machines, offering high stability and precise performance for drilling into hard metals. Extra-short design for greater stability HSS‑G construction for improved wear resistance 135° Point Angle for hard steels Cylindrical shank fits standard chucks Conforms to DIN 1897 for reliable dimensions Precision and Durability for Professional Metalworking Designed for demanding metal applications, this HSS‑G Twist Drill combines a ground geometry that reduces required feed force with a robust material composition. The Type N spiral is optimised for machining ferrous and allied metals, providing reliable chip evacuation and consistent hole quality. The 135° Point Angle shortens the initial penetration time on harder alloys and helps maintain a centred start, which is particularly important when drilling stainless steel or other high‑strength materials. Stable, Space-Saving Design for Tight Setups The extra short overall length delivers improved torsional rigidity and reduced breakage risk when working in confined spaces or on thin sheets. A cylindrical shank ensures universal compatibility with three‑jaw chucks commonly used in Hand Drilling Machines, enabling quick tool changes and secure clamping. Because the shortened form reduces lever‑action forces, operators benefit from steadier guidance and a lower probability of walk‑off during the first cut. Clear Application Guidance and Suitability This Twist Drill is primarily intended for metalworking: alloyed and unalloyed steel, cast steel, grey cast iron, sintered iron, malleable cast iron, non‑ferrous metals and hard plastics. As a Type N HSS tool, it is not optimally matched to very soft materials where specialised geometries perform better. The drill follows DIN 1897 dimensions, making it a dependable choice for workshops that require standardised tools. For tailored recommendations on cutting speeds, coolant strategy or machine settings, MetavCUT quality and METAV Werkzeuge’s advisory service can assist with technical details. For precise metal drilling choose the MetavCUT Twist Drill and contact METAV Werkzeuge for personalised technical advice — eMail: info@metav-werkzeuge.com | Phone: +49 2822 7131930 | WhatsApp: +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 56051-FDA Diameter: 5.1 mm Overall length: 62 mm Spiral length: 26 mm Point angle: 135° Type: Type N Material: HSS‑G Finish / Colour: Bright finished Execution: Extra short Shank execution: Cylindrical For drilling machine: Drilling Machine (Hand Drilling Machine) Model series: Standard Line Application: Drills for metal Norm: DIN 1897 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What are Twist Drills used for? Twist Drills from MetavCUT are primarily used for machining high‑strength materials and larger drill diameters; their classic spiral form is simple to regrind and endures higher loads, making them suitable for sustained metalworking tasks. Which 3 drill types are there? The three main drill categories are metal drills, wood drills and stone/concrete drills, with the MetavCUT Twist Drill belonging to the metal drill group (Type N) optimised for steel and similar materials.

Spiralbohrer (5,2 mm, 135°, Typ N, blank, extra kurz, DIN 1897, HSS-G) von MetavCUT Der Spiralbohrer ist ein extra kurzer HSS-G Bohrer nach DIN 1897 für Metallbohrungen mit Zylinderschaft und wurde für den Einsatz in Handbohrmaschine konzipiert. Extra kurze Bauform für höhere Stabilität HSS-G-Material für erhöhte Standzeit Spitzenwinkel 135° für harte Werkstoffe Zylinderschaft passt in Standard-Bohrfutter Spiralänge 26 mm bei Gesamtlänge 62 mm Mehr Stabilität bei beengten Arbeitsverhältnissen Der Spiralbohrer im extra kurzen Format bietet deutlich mehr Stabilität als lange Ausführungen und reduziert so das Risiko von Bruch und Auslenkung. Durch die verkürzte Gesamt- und Arbeitslänge wird die Verdrehungsfestigkeit erhöht, was besonders beim Bohren in dünnwandigen Blechen und Profilen von Vorteil ist. Anwender profitieren von sicherer Führung und präziseren Bohrungen auch in schwer zugänglichen Bereichen. Materialwahl und Leistungsgewinn für effizientes Arbeiten Der Einsatz des HSS-G Materials sorgt für gute Zähigkeit bei gleichzeitig hoher Schnittfestigkeit. Die geschliffene Ausführung ermöglicht ein bis zu 40 % schnelleres Bohren und erfordert dabei 50 % weniger Anpresskraft gegenüber herkömmlichen HSS-Bohrern, was die Arbeitsleistung steigert und Ermüdung verringert. Der Spitzenwinkel 135° unterstützt das sichere Anbohren in legierten Stählen und zähen Werkstoffen. Geeignete Anwendungen und Maschineneinsatz klar definiert Mit einem Durchmesser von 5,2 mm fällt dieser Bohrer in den Standard-Bereich für den Alltagsgebrauch und ist optimal für Handgeführte Akkubohrschrauber und stationäre Bohrmaschinen geeignet. Typische Werkstoffe sind Baustahl, Aluminium, Gusseisen, Nichteisenmetalle und Hartkunststoffe. Für höchste Präzision empfiehlt es sich, vor dem Bohren anzuzeichnen oder mit einem Zentrierbohrer anzupunken, um ein Wandern des Bohrers zu vermeiden. Für wen dieses Werkzeug entwickelt wurde und praktische Hinweise Der Bohrer richtet sich an Profi-Handwerker sowie anspruchsvolle Heimwerker, die präzise Metallbohrungen erwarten. Der Zylinderschaft passt universell in gängige Dreibackenfutter und vereinfacht den Werkzeugwechsel. Bei sehr hohem Drehmoment kann der Zylinderschaft jedoch zum Durchrutschen neigen; in solchen Fällen empfiehlt sich die Verwendung geeigneter Spannfutter oder alternativer Schaftformen. Für präzise Metallbohrungen empfiehlt MetavCUT den extra kurzen HSS-G Spiralbohrer mit 135° Spitzenwinkel – kontaktieren Sie METAV Werkzeuge per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 für persönliche Beratung und Bestellhilfe. Bezeichnung: Spiralbohrer Marke/Hersteller: MetavCUT SKU: 56052-FDA Durchmesser: 5,2 mm Spitzenwinkel: 135° Typ: Typ N Ausführung: extra kurz Farbe: blank Material: HSS-G Norm: DIN 1897 Gesamtlänge: 62 mm Spiralänge: 26 mm Schaftausführung: Zylinder Für Bohrmaschine: Handbohrmaschine Modellserie: Standard Line Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Wie gut eignet sich der Spiralbohrer von MetavCUT für Edelstahl? Der Spiralbohrer von MetavCUT (Typ N) mit 135° Spitzenwinkel ist speziell für härtere Werkstoffe konzipiert und ermöglicht saubere Anbohrungen in legierten Stählen; bei hochlegiertem Edelstahl sind angepasste Schnittparameter und Kühlung empfehlenswert. Kann der Spiralbohrer von MetavCUT in einer Handbohrmaschine eingesetzt werden? Ja, der Spiralbohrer von MetavCUT ist für den Einsatz in Handbohrmaschine vorgesehen; der Zylinderschaft erlaubt das Einspannen in Standard-Dreibackenfutter, wobei auf ausreichende Spannkraft zu achten ist. Wie wirkt sich die extra kurze Ausführung auf die Standzeit aus? Die extra kurze Bauform des Spiralbohrers von MetavCUT erhöht die Stabilität während des Bohrens und reduziert Bruchrisiken, was zusammen mit dem HSS-G Material zu einer verbesserten Standzeit beiträgt. Warum wurde der Spitzenwinkel 135° gewählt? Der 135° Spitzenwinkel des Spiralbohrers von MetavCUT erleichtert das Anbohren in harten Werkstoffen und verringert das Auslaufen beim Einsetzen, wodurch das Werkstück sauberer und präziser bearbeitet werden kann. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#56052-FDA","sku":"56052-FDA","mpn":"56052-FDA","name":"Spiralbohrer 56052-FDA","description":"Extra kurzer HSS-G Spiralbohrer nach DIN 1897, Durchmesser 5,2 mm, Spitzenwinkel 135°, Typ N, Ausführung extra kurz, Farbe blank, Schaftausführung Zylinder, Gesamtlänge 62 mm, Spiralänge 26 mm; Konzipiert für Metallbohrungen mit Handbohrmaschine; hohe Stabilität und längere Standzeit durch geschliffene Ausführung.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741b/logo-metav-1200-1200.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741e/logo-metav-1200-900.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png"],"additionalProperty":[{"@type":"PropertyValue","name":"Bezeichnung","value":"Spiralbohrer"},{"@type":"PropertyValue","name":"Marke/Hersteller","value":"MetavCUT"},{"@type":"PropertyValue","name":"Durchmesser","value":"5,2 mm"},{"@type":"PropertyValue","name":"Spitzenwinkel","value":"135°"},{"@type":"PropertyValue","name":"Typ","value":"Typ N"},{"@type":"PropertyValue","name":"Ausführung","value":"extra kurz"},{"@type":"PropertyValue","name":"Farbe","value":"blank"},{"@type":"PropertyValue","name":"Material","value":"HSS-G"},{"@type":"PropertyValue","name":"Norm","value":"DIN 1897"},{"@type":"PropertyValue","name":"Gesamtlänge","value":"62 mm"},{"@type":"PropertyValue","name":"Spiralänge","value":"26 mm"},{"@type":"PropertyValue","name":"Schaftausführung","value":"Zylinder"},{"@type":"PropertyValue","name":"Für Bohrmaschine","value":"Handbohrmaschine"},{"@type":"PropertyValue","name":"Modellserie","value":"Standard Line"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"Wie gut eignet sich der Spiralbohrer von MetavCUT für Edelstahl?","acceptedAnswer":{"@type":"Answer","text":"Der Spiralbohrer von MetavCUT (Typ N) mit 135° Spitzenwinkel ist für härtere Werkstoffe ausgelegt und ermöglicht saubere Anbohrungen in legierten Stählen; bei hochlegiertem Edelstahl sind angepasste Schnittparameter und Kühlung empfehlenswert."}},{"@type":"Question","name":"Kann der Spiralbohrer von MetavCUT in einer Handbohrmaschine eingesetzt werden?","acceptedAnswer":{"@type":"Answer","text":"Ja, der Spiralbohrer von MetavCUT ist für den Einsatz in Handbohrmaschine vorgesehen; der Zylinderschaft erlaubt das Einspannen in Standard-Dreibackenfutter, wobei auf ausreichende Spannkraft zu achten ist."}},{"@type":"Question","name":"Wie wirkt sich die extra kurze Ausführung auf die Standzeit aus?","acceptedAnswer":{"@type":"Answer","text":"Die extra kurze Bauform des Spiralbohrers von MetavCUT erhöht die Stabilität während des Bohrens und reduziert Bruchrisiken, was zusammen mit dem HSS-G Material zu einer verbesserten Standzeit beiträgt."}},{"@type":"Question","name":"Warum wurde der Spitzenwinkel 135° gewählt?","acceptedAnswer":{"@type":"Answer","text":"Der 135° Spitzenwinkel des Spiralbohrers von MetavCUT erleichtert das Anbohren in harten Werkstoffen und verringert das Auslaufen beim Einsetzen, wodurch das Werkstück sauberer und präziser bearbeitet werden kann."}}]},{"@type":"ItemPage","url":"https://metav-shop.de","dateModified":"2026-05-04T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Spiralbohrer"},{"@type":"Thing","name":"HSS-G Bohrer"},{"@type":"Thing","name":"DIN 1897 Standard"}],"mentions":[{"@type":"Thing","name":"Zylinderschaft"},{"@type":"Thing","name":"Extra kurze Bauform"},{"@type":"Thing","name":"Spitzenwinkel 135°"}]}]}

Twist Drill — Extra Short, 5.3 mm, 135° tip, Type N, Bright Finished, HSS‑G, DIN 1897 by MetavCUT The Twist Drill Type N is designed for precise metal drilling with an extra‑short geometry that improves stability and performance in hand and angle drilling applications. Extra short design for improved stability HSS‑G cutting for faster metal drilling 135° tip optimized for hard materials Cylindrical shank for standard chuck compatibility Conforms to DIN 1897 for robust reliability Greater stability in confined workplaces and thin materials The extra‑short configuration reduces overhang and increases resistance to breakage, making this drill ideal when working in confined spaces or with thin sheets and profiles. The shortened overall length improves torque transmission and reduces vibration, which enhances hole quality and extends tool life. This compact design is particularly suited to handheld and angle drilling tasks where access and control matter most. Faster cutting with lower feed force thanks to HSS‑G A ground HSS‑G cutting edge accelerates metalworking tasks: up to 40% faster drilling and roughly 50% less required feed force compared with conventional HSS variants in comparable conditions. This performance advantage reduces operator effort and can shorten cycle times in manual and light industrial operations. HSS‑G is engineered for durability when machining alloyed and unalloyed steels as well as cast materials. Precise centring and suitability for hard materials The 135° tip geometry offers a reduced chisel edge and better centring on difficult surfaces, which lowers friction during entry and helps when drilling stainless steel and other hard alloys. The Type N normal spiral is the classic metalworking flute form, combining efficient chip removal with reliable cutting action. When a clear explanation is helpful: a larger tip angle distributes cutting forces over a broader area, improving life and reducing tip wear on tough materials. Universal fit and targeted applications With a cylindrical shank the drill fits most three‑jaw chucks, allowing quick preparation for standard drilling rigs and hand drills. Designed under DIN 1897 as part of the Standard Line, this tool by MetavCUT is aimed at technicians, maintenance professionals and workshop users who require dependable performance drilling metals such as steel, cast iron, sintered iron, non‑ferrous metals and hard plastics. The extra‑short format also simplifies work in assembly and repair where space is limited. For demanding metalwork choose the MetavCUT Twist Drill for its extra‑short, robust design — METAV Werkzeuge offers expert advice and technical support via info@metav-werkzeuge.com or call +49 2822 7131930, WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 56053-FDA Diameter: 5.3 mm Tip angle: 135° Type: Type N Finish: Bright finished Execution: Extra short Material: HSS‑G Overall length: 62 mm Spiral length: 26 mm Shank execution: Cylindrical Model series: Standard Line For drilling machine: Drilling Machine Application: Drills for metal Norm: DIN 1897 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill best used for? The MetavCUT Twist Drill Type N is primarily intended for metalworking and excels when drilling alloyed and unalloyed steels, cast materials and hard plastics; its extra‑short form improves stability in thin materials and confined working spaces. Can the MetavCUT Twist Drill be used in hand drills? Yes, the MetavCUT Twist Drill with a cylindrical shank is suitable for Hand and Angle Drills and fits standard three‑jaw chucks, offering universal compatibility for workshop and on‑site applications. For what is a Twist Drill used? A Twist Drill is mainly applied to the machining of high‑strength workpieces and larger drill diameters; its form is easy to grind and withstands greater stresses. Which three drill types exist? The main categories are metal drills, wood drills and stone/concrete drills. Why are twist drills pointed? Pointing reduces the chisel edge at the tip, significantly lowering friction and required feed force while improving centring in the workpiece. Can a metal drill be used to drill wood? A metal drill can be used in wood but generally offers poorer guidance and less clean results; however, it is easier to resharpen and has lower self‑feed tendency. For which drilling depths is the twist drill most commonly used? Solid drilling is typically performed with a twist drill; it is most common for diameters up to 20 mm and drilling depths up to 100 mm. Which is better, HSS or HSSE? The common belief that HSSE is categorically superior to HSS is incorrect; selection should consider specific working conditions to justify any higher purchase cost.

Twist Drill — Type N · 5.4 mm · 135° · Extra short · Bright finished · HSS‑G · DIN 1897 · MetavCUT The Twist Drill by MetavCUT is an extra‑short Type N metal drill designed for precise, stable drilling in hand and angle drilling machines. Extra‑short design for higher stability 135° tip for hard materials HSS‑G ground for faster drilling Cylindrical shank fits standard chucks Greater Stability and Faster Penetration for Metalwork The extra‑short design gives this drill improved stability and reduced breakage risk compared with standard lengths. For workshop tasks where space is limited or walls are thin, the shorter overall length provides greater torsional rigidity and easier handling in a Hand Drilling Machine. The ground HSS‑G cutting geometry reduces required axial force and allows up to 40% faster drilling in many steels, which translates to more efficient working cycles and less operator fatigue. Better Entry and Longevity on Tough Materials Equipped with a 135° tip, the drill reduces chipping and improves centring when working with harder metals such as stainless and alloyed steels. A larger tip angle shortens the initial entry time and lowers the tendency to wander on the surface. The Type N spiral is the classic metal geometry, optimised for cutting performance in ferrous materials while maintaining durability under higher loads. Universal Fit and Practical Use Cases A smooth cylindrical shank ensures compatibility with standard three‑jaw chucks found on handheld and bench drilling machines. While universally fitting, users should be aware that cylindrical shanks can slip under very high torque; for such applications, alternative shank forms may be preferable. This tool is particularly suitable for drilling alloyed and unalloyed steel, cast and sintered irons, non‑ferrous metals and hard technical plastics where clean, reliable holes are required. Handling, Sharpening and Application Advice The extra‑short twist drill is straightforward to resharpen and maintain, which keeps lifecycle costs down. By slightly regrinding the point (reducing the web thickness), cutting forces fall and centring improves, meaning less feed force is needed and the drill stays steadier in the hole. For best results, use appropriate cutting speeds and coolant for the workpiece material and ensure the chuck is properly tightened to avoid slippage. MetavCUT’s Twist Drill combines compact robustness with high metal‑cutting performance — for personalised tool advice or application support please contact METAV Werkzeuge: info@metav-werkzeuge.com · Tel. +49 2822 7131930 · WhatsApp +49 170 2837271 Technical information Designation: Twist Drill Brand: MetavCUT SKU: 56054-FDA Diameter: 5.4 mm Tip angle: 135° Type: Type N Finish: Bright finished Execution: Extra short Material: HSS-G Shank execution: Cylindrical Overall length: 62 mm Spiral length: 26 mm Norm: DIN 1897 Application: Drills for metal Model series: Standard Line Intended machine: Drilling Machine (Hand Drill) Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Is the MetavCUT Twist Drill suitable for stainless steel and hardened metals? The MetavCUT Twist Drill (Type N) with its 135° tip is especially suited to harder workpiece materials; the larger tip angle improves centring and reduces chipping, making it a good choice for many stainless and alloyed steels when used with correct cutting speeds and coolant. Which machines work best with this Twist Drill from MetavCUT? This Twist Drill is intended for use in a Hand Drilling Machine or similar drilling equipment; the cylindrical shank fits standard three‑jaw chucks, making it convenient for portable and bench drilling tasks. For what is a Twist Drill used? A Twist Drill is mainly employed for machining high‑strength materials and larger hole diameters. Its form is easy to resharpen and it withstands substantial loads, which makes it suitable for demanding metalworking operations. Which 3 drill types are there? There are three primary drill types to consider: Metal drills, Wood drills, and Stone/Concrete drills. Why are Twist Drills sharpened at the point? Point sharpening reduces the web thickness at the tip, which lowers friction and cutting forces; this means less feed force is necessary and the drill centres better in the workpiece, improving hole quality. Can a metal drill be used for wood? A metal drill can be used in wood, but guidance and finish are usually inferior to a dedicated wood drill. Metal drills are easier to resharpen and have less self‑feeding action, so results may vary. At what drilling depths is the Twist Drill most commonly used? Twist Drills are the standard tool for through‑hole drilling and are most commonly applied for diameters up to about 20 mm and hole depths up to roughly 100 mm, covering most routine metal drilling tasks. Is HSS or HSSE better for my application? The blanket assumption that HSSE steels are always superior to HSS is incorrect. Choice should be based on specific working conditions and whether the performance justifies the higher cost; evaluate cutting speeds, material and required tool life before deciding.

Twist Drill (Type N) — 5.5 mm, 135° tip, Extra Short, Bright Finished, HSS-G, DIN 1897 — by MetavCUT The Twist Drill Type N is an extra-short HSS-G metal drill designed for Hand and Angle Drilling Machines to deliver stable, high-performance holes in confined or thin-walled workpieces. Extra-short design for higher stability 135° tip for hard and alloyed steels HSS‑G material for prolonged tool life Cylindrical shank fits standard chucks Suited to hand and angle drilling in metal Greater Stability and Safer Drilling in Tight Spaces The Extra-short geometry reduces overall length while keeping the Flute and cutting geometry effective; this increases Stability and lowers the risk of breakage when working in confined areas or with thin sheets. For tasks like drilling profiles, plates or assemblies where space is restricted, the compact design translates into more controlled handling and clearer alignment, which reduces rework. The designation DIN 1897 signals conformity with the short-length variant of the standard, aiding in reliable tool selection. Faster Cutting and Lower Feed Force on Tough Materials A 135° tip and the Type N normal spiral combine to make chip formation and penetration more gradual on harder materials. The HSS‑G construction ensures toughness with good wear resistance; tests with similar ground HSS drills show up to 40% faster drilling with about 50% less feed force compared with conventional HSS blanks. This means less operator fatigue and smoother results when machining Alloyed and Unalloyed Steel, Cast Steel, Cast Iron, Sintered Iron, Non‑Ferrous Metals and Hard Plastics. Reliable Fit and Practical Use in Workshops The Cylindrical Shank is compatible with standard Three‑Jaw Chucks, so the twist drill is easy to mount in common handheld and benchtop drilling machines. With an Overall Length of 66 mm and a Flute Length of 28 mm, the geometry is optimised for typical metalworking tasks while keeping bending forces low. The bright finish simplifies chip evacuation and inspection. Note that a smooth cylindrical shank can slip under very high torque; using a well‑clamped chuck and appropriate speeds avoids this. Who Benefits from This Choice Maintenance technicians, sheet‑metal workers and general workshops will value the combination of compactness and material capability. The tool is particularly beneficial when drilling in assemblies, thin wall components or areas where a full‑length drill cannot be used. For those who need a universal, robust solution for metal drilling with easy mounting in standard chucks, this model from the Standard Line offers dependable performance. How the Technology Works — Simple Explanation for Everyday Use Type N describes the classic normal spiral suited for metalwork; the larger 135° tip angle reduces the aggressiveness of the cut, which helps with centring and decreases tool wander in tough materials. HSS‑G is a high‑speed steel grade with improved grinding quality and heat resistance compared with basic HSS, making it a pragmatic choice for general metal drilling. If centring is critical, a pilot or spot drill can be used before final hole drilling to ensure maximum accuracy. Strong recommendation: For stable, efficient metal drilling in constrained spaces choose the MetavCUT Twist Drill Type N with Extra Short execution — for personalised technical advice or to confirm fit for a specific application contact METAV Werkzeuge; comprehensive consultation is available by email at info@metav-werkzeuge.com, by phone at +49 2822 7131930 or via WhatsApp at +49 170 2837271 Technical Details for Exact Matching Designation: Twist Drill Brand: MetavCUT SKU: 56055-FDA Diameter: 5.5 mm Tip Angle: 135° Type: Type N Execution / Length: Extra Short Material: HSS‑G Standard: DIN 1897 Finish / Colour: Bright Finished Shank Design: Cylindrical Overall Length: 66 mm Flute Length: 28 mm Intended Machine: Drilling Machine (Hand / Angle Drills suitable) Application: Drills for Metal Model Series: Standard Line Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill used for? The MetavCUT Twist Drill Type N is primarily used for drilling through high‑strength materials and for larger hole diameters in metalworking; its form allows straightforward resharpening and it endures higher loads, making it suitable for alloys, cast materials and hard plastics in workshop and maintenance environments. Which three drill types exist? Commonly differentiated drill types are Metal Drills, Wood Drills and Stone/Concrete Drills, and the MetavCUT Twist Drill falls into the metal drill category designed specifically for metalworking applications.

Twist Drill — Type N, 5.6 mm, 135° tip, extra short, Bright finished, HSS‑G, DIN 1897 (MetavCUT) The Twist Drill Type N extra short by MetavCUT is a compact HSS‑G metalworking bit optimised for hand and drilling machines, designed for precise, high‑stability drilling in tougher materials. Extra‑short design for greater stability HSS‑G material for faster metal drilling 135° tip for harder materials like stainless steel Cylindrical shank fits standard three‑jaw chucks Increased performance through HSS‑G construction The HSS‑G material offers improved cutting performance compared with conventional HSS, enabling up to 40% faster drilling while requiring significantly less feed force. This results in reduced operator fatigue and more consistent hole quality when working with alloyed and unalloyed steels, cast materials and non‑ferrous metals. For users who value speed and durability, the hardened high‑speed steel composition is a decisive advantage. Stability and safety from the extra‑short geometry Because the bit is extra short relative to DIN 1897 standards, the reduced overall length and shorter flute length increase rigidity and lower the risk of breakage. This geometry is particularly beneficial when drilling in thin sheets or confined spaces, where a long overhang would cause vibration or chatter. The compact form factor therefore improves centring and repeatability for precision tasks. Tip geometry and shank: better entry and universal clamping A 135° tip angle reduces the tendency to wander on hard surfaces and shortens pilot time when penetrating tougher materials like stainless steel. The cylindrical shank ensures universal compatibility with standard three‑jaw chucks, allowing quick changes in common hand and bench drilling setups. For high‑torque applications, users should verify chuck grip to avoid slippage. Practical applications and user guidance This extra‑short Twist Drill (Type N) is aimed at mechanics, maintenance technicians and metalworkers who need reliable, compact drills for production or repair work. It is particularly suited to drilling in steel, cast iron, sintered iron and hard plastics. For best results, use appropriate cutting fluid on harder alloys and moderate speeds to prolong tool life and ensure cleaner holes. We recommend the MetavCUT extra short HSS‑G Twist Drill for precision metalworking and confined‑space drilling; for personalised technical guidance or application support contact METAV Werkzeuge — 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp +49 170 2837271 Designation: Twist Drill (Spiralbohrer) Brand: MetavCUT SKU: 56056-FDA Diameter: 5.6 mm Total length: 66 mm Spiral length: 28 mm Tip angle: 135° Type: Type N Execution: extra short Colour / Finish: Bright finished Material: HSS‑G Shank design: Cylindrical Standard: DIN 1897 Intended use: Drills for metal / Drilling Machine compatibility (Hand Drilling Machine) Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Is the MetavCUT Twist Drill Type N extra short suitable for stainless steel? The MetavCUT Twist Drill Type N extra short is designed with a 135° tip specifically to improve entry into harder materials such as stainless steel; combined with HSS‑G material this makes it well suited for such applications when used with appropriate cutting fluid and speeds. Can the MetavCUT Twist Drill be used in a standard hand drill? Yes, the MetavCUT Twist Drill Type N extra short features a cylindrical shank that fits standard three‑jaw chucks, making it compatible with most hand and bench drilling machines; ensure firm chuck clamping to prevent slippage under higher torque. What are twist drills used for? Twist Drills are primarily used for machining high‑strength materials and larger hole diameters. They are relatively easy to re‑grind and withstand higher loads, which makes them suitable for demanding metalworking tasks. Which three drill types exist? The three main drill types are metal drills, wood drills and stone/concrete drills. Why are twist drills sharpened (pointed)? Sharpening reduces the cross‑edge at the tip of the Twist Drill, significantly lowering friction and required feed force while improving centring accuracy in the workpiece. Can a metal twist drill be used for wood? A metal twist drill can be used in wood, but it generally provides poorer guidance and a less clean hole than a dedicated wood bit; however, it is easier to re‑grind and exhibits less self‑feeding. For which drilling depths is the twist drill most commonly used? A full‑bore hole is commonly made with a Twist Drill. For diameters up to 20 mm and drilling depths up to 100 mm the Twist Drill is the most frequently used tool. Is HSS or HSSE better? The common belief that HSSE steels are inherently superior to HSS is incorrect. When choosing, consider whether the specific working conditions justify the higher purchase price of HSSE.

Twist Drill — Type N, Ø 5.7 mm, 135°, HSS‑G, extra short, bright finished, DIN 1897 The Twist Drill Type N is an extra short HSS‑G metal drill for Drilling Machines, designed for stable, fast and precise holes in a wide range of ferrous and non‑ferrous materials. Extra short design for improved stability HSS‑G material for demanding metal work 135° tip angle for harder workpieces Cylindrical shank for standard chucks Conforms to DIN 1897 for consistent geometry High performance for metalworking tasks With a HSS‑G cutting body and a 135° tip angle, this extra short drill bit delivers reliable penetration into harder materials such as alloyed and unalloyed steel, cast steel and non‑ferrous metals. The ground geometry reduces required feed force by up to 50% and can enable up to 40% faster drilling compared with conventional HSS bits, which translates into measurable productivity gains in workshop and maintenance environments. This makes the bit particularly suitable where robust, reproducible results are required under manual or machine operation. Compact geometry reduces breakage and improves control Designed to the DIN 1897 extra short specification, the reduced overall length provides greater torsional stiffness and lower bending, reducing the risk of fracture during handheld or confined‑space work. The shortened flute and working length improve guidance when drilling thin sheets, profiles or close‑to‑edge holes, allowing cleaner starts and fewer chattering issues. For technicians facing limited access or when a stable, controllable cut is critical, the compact form significantly enhances handling and safety. Universal mounting and consistent centring Equipped with a cylindrical shank, the drill seats securely in standard three‑jaw chucks, offering universal compatibility with common Drilling Machines and hand drills. The Type N normal spiral ensures efficient chip evacuation and a balanced cut for metal applications, while the grind and tip geometry aid centring without aggressive self‑feeding. This combination supports consistent hole quality across repeated operations and simplifies tool selection for general metal fabrication and repair tasks. Intended users and practical advantages Metalworkers, maintenance technicians and engineering workshops will value the durability and serviceability of this extra short bit. It is engineered for frequent resharpening and lower consumable turnover, which contributes to less tool waste and longer operational life. The robust design suits both professional industrial use and demanding hobbyist projects, combining precise holemaking with the convenience of a universally fitting shank and well defined cutting angles. Strong recommendation: For demanding metal drilling, choose the MetavCUT Twist Drill Type N with extra short geometry for improved stability and controlled cutting — METAV Werkzeuge offers expert technical advice and support via eMail: info@metav-werkzeuge.com, Phone: +49 2822 7131930, WhatsApp: +49 170 2837271 Technical Specifications for reliable selection Designation: Twist Drill Marke: MetavCUT SKU: 56057-FDA Diameter: 5.7 mm Tip angle: 135° Type: Type N Execution: extra short Colour: bright finished Material: HSS‑G Standard: DIN 1897 Overall length: 66 mm Spiral length: 28 mm Shank: Cylindrical Model series: Standard Line Application: Drills for metal For drilling machine: Drilling Machine Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials is the MetavCUT Twist Drill Type N suitable for? The MetavCUT Twist Drill Type N is designed primarily for metalwork and is suitable for alloyed and unalloyed steel, cast steel, cast iron, sintered iron, malleable cast iron, non‑ferrous metals and hard plastics; its HSS‑G composition and 135° tip assist in penetrating tougher workpieces with less feed force. How does the extra short design of the Twist Drill benefit workshop tasks? An extra short Twist Drill from MetavCUT reduces bending and torsional strain compared with standard lengths, improving stability and lowering the chance of breakage; this geometry is particularly advantageous when drilling thin materials or working in confined spaces where control and guidance are essential. For what is a Twist Drill mainly used? It is mainly applied when machining high‑strength materials and larger drill diameters; the shape is easy to regrind and withstands greater loads. Which three drill types exist? The three main drill categories are metal drills, wood drills and stone/concrete drills. Why are Twist Drills point‑sharpened? Point‑sharpening reduces the web thickness at the tip, markedly lowering friction and thus required feed forces while improving centring of the drill in the workpiece. Can a metal drill be used for wood? A metal drill can be used in wood but typically provides poorer guidance and a less clean hole; however, it is easier to resharpen and exhibits reduced self‑feeding compared with specialised wood drills.

Spiralbohrer 5,8 mm, HSS-G, extra kurz (Typ N) – DIN 1897, 135° Spitzenwinkel, Zylinderschaft, blank – MetavCUT Standard Line Der Spiralbohrer von MetavCUT ist ein extra kurzer HSS-G Bohrer für präzise Metallbohrungen mit Handbohrmaschine, ideal für Bleche, Profile und mittlere Stahlstärken. Extra kurze Bauform für mehr Stabilität Bis zu 40 % schnelleres Bohren bei geringerem Kraftaufwand 135° Spitzenwinkel für Anbohrverhalten in harten Werkstoffen Zylinderschaft für universelle Aufnahme im Dreibackenfutter Geeignet für legierte und unlegierte Stähle sowie Nichteisenmetalle Kompakte Länge erhöht Standfestigkeit und reduziert Bruchrisiko Die extra kurze Ausführung reduziert Hebelwirkung und Vibration, was die Stabilität beim Bohren deutlich erhöht. Bei beengten Platzverhältnissen sorgt die geringere Gesamtlänge von 66 mm für bessere Handhabung in Winkelaufnahmen oder an Kanten. Durch die kürzere Spirallänge (28 mm) werden Späne schneller transportiert, wodurch die Bruchneigung bei dünnen Werkstücken sinkt. Der Einsatz eines HSS-G Materials bietet höhere Verschleißfestigkeit gegenüber einfachem Schnellarbeitsstahl und verlängert die Standzeit bei Serienbelastung. Präzise Anwendungen in Werkstatt und Montage sicher ausführen Als Bohrer im Standard-Bereich eignet sich dieses Werkzeug besonders für den Alltagsgebrauch in Werkstatt, Montage und Heimwerken. Der Spitzenwinkel 135° ermöglicht ein kontrolliertes Eindringen in härtere Materialien und reduziert Aufspitzen und Ausrisse. Bei der Bearbeitung von Baustahl, Guss oder Temperguss liefert der Bohrer gleichmäßige Bohrbilder; für hochpräzise Passungen empfiehlt sich vorheriges Anpunkten mit einem Zentrierbohrer, um das Wandern des Bohrers zu vermeiden. Universelle Schaftform und praktische Einsatzhinweise Der Zylinderschaft erlaubt das Einspannen in gängige Dreibackenfutter und macht den Bohrer kompatibel mit handelsüblichen Handbohrmaschinen. Vorteil ist die einfache Montage und der universelle Einsatz; Nachteil kann unter sehr hohem Drehmoment ein leichtes Durchrutschen sein. Für erhöhte Rundlaufgenauigkeit und sichere Kraftübertragung empfiehlt sich eine sorgfältige Spannprüfung und gegebenenfalls Einsatz eines Spannzylinders oder einer Winkelschraubzwinge. Anwendungstipps für saubere Bohrbilder und lange Lebensdauer Vor dem Bohren sollte die Werkstückoberfläche entgratet und bei Bedarf gekühlt werden, insbesondere bei dichten oder legierten Werkstoffen. Bei Durchmessern im Standardbereich reicht in vielen Fällen direktes Bohren, bei hohen Genauigkeitsanforderungen ist Anpunkten sinnvoll. Reinigung der Bohrung und gelegentliches Nachschärfen erhalten die Schneidleistung; die robuste Standard Line Ausführung von MetavCUT bietet hier eine ausgewogene Kombination aus Standzeit und Wirtschaftlichkeit. Empfehlung: Den HSS-G Bohrer von MetavCUT als zuverlässige Wahl für präzise Metallbohrungen wählen und bei Fragen unsere technische Beratung per E‑Mail unter info@metav-werkzeuge.com oder telefonisch +49 2822 7131930 nutzen Bezeichnung: Spiralbohrer Marke: MetavCUT SKU: 56058-FDA Durchmesser: 5,8 mm Material: HSS-G Ausführung: extra kurz Typ: Typ N Norm: DIN 1897 Spitzenwinkel: 135° Schaftausführung: Zylinder Farbe: blank Gesamtlänge: 66 mm Spirallänge: 28 mm Für Bohrmaschine: Handbohrmaschine Modellserie: Standard Line Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Ist der Spiralbohrer von MetavCUT für Handbohrmaschinen geeignet? Der Spiralbohrer von MetavCUT wurde speziell für den Einsatz in Handbohrmaschinen konzipiert und bietet durch die extra kurze Bauform bessere Stabilität bei Arbeiten an Blechen und Profilen. Für welche Materialien ist der MetavCUT Spiralbohrer ausgelegt? Der MetavCUT Spiralbohrer eignet sich für legierten und unlegierten Stahl, Gussstahl, Gusseisen, Sintereisen, Temperguss, Nichteisenmetalle und Hartkunststoff; bei sehr zähen Werkstoffen empfiehlt sich der Einsatz von Kühlung. Warum ist der 135° Spitzenwinkel beim MetavCUT Spiralbohrer vorteilhaft? Der 135° Spitzenwinkel des MetavCUT Spiralbohrers reduziert das Aufreißen beim Anbohren in härtere Werkstoffe und verkürzt die Anbohrzeit, wodurch kontrolliertere Bohrvorgänge möglich sind. Wie vermeide ich ein Durchrutschen im Bohrfutter mit dem MetavCUT Spiralbohrer? Um ein Durchrutschen des Zylinderschafts beim MetavCUT Spiralbohrer zu verhindern, sollte das Dreibackenfutter sauber und fest gespannt sowie bei hohen Drehmomenten ein Spannzylinder oder ein anderes Schrumpfspannsystem verwendet werden. Bietet MetavCUT Beratung, wenn unspezifische Fragen zur Anwendung bestehen? Bei Unsicherheit, ob der Spiralbohrer von MetavCUT die Anforderungen erfüllt, steht der Händler mit fachkundiger Beratung zur Verfügung; kontaktieren Sie info@metav-werkzeuge.com, rufen Sie +49 2822 7131930 an oder nutzen Sie WhatsApp unter +49 170 2837271. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#56058-FDA","sku":"56058-FDA","mpn":"56058-FDA","name":"Spiralbohrer 5,8 mm, HSS-G, extra kurz (Typ N)","description":"Extra kurzer Spiralbohrer 5,8 mm aus HSS-G mit 135° Spitzenwinkel, Zylinderschaft und DIN 1897 Norm; konzipiert für präzise Metallbohrungen mit Handbohrmaschine in Blechen, Profilen und mittleren Stahlstärken.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741b/logo-metav-1200-1200.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741e/logo-metav-1200-900.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png"],"additionalProperty":[{"@type":"PropertyValue","name":"Bezeichnung","value":"Spiralbohrer"},{"@type":"PropertyValue","name":"Marke","value":"MetavCUT"},{"@type":"PropertyValue","name":"Durchmesser","value":"5,8 mm"},{"@type":"PropertyValue","name":"Material","value":"HSS-G"},{"@type":"PropertyValue","name":"Ausführung","value":"extra kurz"},{"@type":"PropertyValue","name":"Typ","value":"Typ N"},{"@type":"PropertyValue","name":"Norm","value":"DIN 1897"},{"@type":"PropertyValue","name":"Spitzenwinkel","value":"135°"},{"@type":"PropertyValue","name":"Schaftausführung","value":"Zylinder"},{"@type":"PropertyValue","name":"Farbe","value":"blank"},{"@type":"PropertyValue","name":"Gesamtlänge","value":"66 mm"},{"@type":"PropertyValue","name":"Spirallänge","value":"28 mm"},{"@type":"PropertyValue","name":"Für Bohrmaschine","value":"Handbohrmaschine"},{"@type":"PropertyValue","name":"Modellserie","value":"Standard Line"},{"@type":"PropertyValue","name":"Eignung","value":"Legierte und unlegierte Stähle, Guss, Temperguss, Nichteisenmetalle, Hartkunststoff"},{"@type":"PropertyValue","name":"Vorteile","value":"Mehr Stabilität, geringere Bruchneigung, schnelleres Bohren"},{"@type":"PropertyValue","name":"Hersteller","value":"Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"Ist der Spiralbohrer 5,8 mm von MetavCUT für Handbohrmaschinen geeignet?","acceptedAnswer":{"@type":"Answer","text":"Der Spiralbohrer 5,8 mm von MetavCUT wurde für den Einsatz in Handbohrmaschinen entwickelt und bietet durch die extra kurze Ausführung erhöhte Stabilität bei Blechen und Profilen."}},{"@type":"Question","name":"Für welche Materialien eignet sich der MetavCUT Spiralbohrer 5,8 mm?","acceptedAnswer":{"@type":"Answer","text":"Der MetavCUT Spiralbohrer 5,8 mm aus HSS-G ist geeignet für legierte und unlegierte Stähle, Gussstahl, Gusseisen, Sintereisen, Temperguss, Nichteisenmetalle und Hartkunststoff; bei sehr zähen Werkstoffen wird Kühlung empfohlen."}},{"@type":"Question","name":"Warum ist der 135° Spitzenwinkel beim Spiralbohrer 5,8 mm vorteilhaft?","acceptedAnswer":{"@type":"Answer","text":"Der 135° Spitzenwinkel des Spiralbohrers 5,8 mm reduziert Aufspitzen beim Anbohren in härtere Werkstoffe und ermöglicht kontrolliertere Bohrvorgänge mit schnellerem Eindringen."}},{"@type":"Question","name":"Wie vermeide ich ein Durchrutschen im Bohrfutter mit dem MetavCUT Spiralbohrer 5,8 mm?","acceptedAnswer":{"@type":"Answer","text":"Um ein Durchrutschen des Zylinderschafts des MetavCUT Spiralbohrers 5,8 mm zu verhindern, sollte das Dreibackenfutter sauber und fest gespannt werden; bei hohen Drehmomenten empfiehlt sich ein Spannzylinder oder ein alternatives Schrumpfspannsystem."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/spiralbohrer-5-8mm-hss-g-extra-kurz-typ-n-din-1897","dateModified":"2026-03-31T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Spiralbohrer Standard Line"},{"@type":"Thing","name":"Extra kurze Bauform für mehr Stabilität"},{"@type":"Thing","name":"HSS-G Material für längere Standzeit"}],"mentions":[{"@type":"Thing","name":"Zylinderschaft für Dreibackenfutter"},{"@type":"Thing","name":"DIN 1897 Norm"},{"@type":"Thing","name":"135° Spitzenwinkel für harte Werkstoffe"}]}]}

Twist Drill — MetavCUT Type N, 5.9 mm, 135° Point, HSS‑G, Extra Short, Bright Finish, DIN 1897 An Twist Drill (Type N) for Drilling Machines providing extra‑short stability and precise metal drilling in confined spaces. MetavCUT Type N for metal drilling Extra Short design for greater stability 135° point angle for harder materials Cylindrical shank fits standard three‑jaw chucks HSS‑G ground for faster, lower‑force drilling High-performance drilling for hardened and alloyed metals The extra‑short HSS‑G Twist Drill delivers improved stability and reduced breakage risk when working with steels and other hard materials. The 135° point angle optimises penetration in tougher alloys and shortens the pilot phase, resulting in more efficient cutting when compared with standard‑length drills. Thanks to the ground geometry, the Tool requires less axial force and allows for controlled cutting even under demanding conditions. Reliable results in tight or thin‑walled assemblies Short overall length and reduced flute length make this Twist Drill especially suitable for work in confined spaces or thin materials such as sheet metal and profiles. The Extra Short format increases torsional stiffness and reduces chatter, which improves hole quality and concentricity. This construction is a practical choice for Hand Drilling Machines and situations where workspace is limited. Simple mounting and universal compatibility Equipped with a Cylindrical shank, this Twist Drill is compatible with standard three‑jaw chucks and thus integrates easily into existing workshop setups. The classic Type N spiral geometry is optimised for metalworking and offers straightforward re‑sharpening when required. For operations demanding high repeatability, the combination of HSS‑G material and precise grinding ensures consistent performance across batches. Target users and recommended applications Designed for machinists, maintenance technicians and industrial workshops, the MetavCUT Twist Drill is targeted at drilling tasks in legated and unlegated steel, cast steel, cast iron, sintered iron, non‑ferrous metals and hard plastics. The tool is particularly advantageous where quick, accurate holes are needed in challenging materials or restricted environments, providing a balance of durability and ease of use. Strong recommendation: Choose the MetavCUT Twist Drill (Type N) with Extra Short HSS‑G geometry for precision metalworking in confined spaces — METAV Werkzeuge offers expert technical advice and selection support at info@metav-werkzeuge.com or by phone +49 2822 7131930, WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 56059-FDA Diameter: 5.9 mm Total Length: 66 mm Spiral Length: 28 mm Point Angle: 135° Type: Type N Execution: Extra Short Colour/Finish: Bright Finished Shank Execution: Cylindrical (Round Shank) Material: HSS‑G Standard: DIN 1897 For Machine: Drilling Machine (Handbohrmaschine) Model Series: Standard Line Application: Drills for Metal Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the main use of a Twist Drill? A MetavCUT Twist Drill (Type N) is primarily used for machining high‑strength materials and larger drill diameters; its form is easy to re‑grind and resists higher loads, making it suitable for demanding metalworking tasks. Which three drill types are commonly distinguished? Common categories are Metal Drills (such as the MetavCUT Twist Drill Type N), Wood Drills, and Stone/Concrete Drills. Why are Twist Drills sharpened at the tip? Sharpening reduces the cross‑cut at the tip of a Twist Drill, significantly lowering friction and required feed forces while improving centring and hole start accuracy for MetavCUT drills. Can a metal Twist Drill be used in wood? A metal drill like the MetavCUT Twist Drill can be used in wood but will guide less well and produce a less clean finish; however, it is easier to re‑grind and exhibits lower self‑feeding tendencies. For which drilling depths is the Twist Drill most commonly used? A through hole in solid material is typically executed with a Twist Drill. For diameters up to 20 mm and depths up to 100 mm, the Twist Drill remains the most frequently used tool.

MetavCUT Twist Drill — 5 mm, 135° Tip, Type N, Bright Finished, Extra Short, DIN 1897, HSS-G The MetavCUT Twist Drill is a precision Type N metal drill designed for handheld and drilling-machine use, offering an extra short design and a 135° tip for reliable performance in harder materials. Extra-short geometry for greater stability HSS‑G construction for high wear resistance 135° tip suited to harder metals Cylindrical shank for universal chuck fit Complies with DIN 1897 for consistent dimensions Increased Cutting Stability and Faster Drilling Thanks to its Extra Short design, this twist drill delivers noticeably higher stability during operation. The reduced overall length lowers the lever arm and diminishes the risk of breakage, which is especially helpful when working in confined spaces or with thin-walled components. The HSS‑G material and optimized flute geometry contribute to a cutting action that requires less axial pressure, enabling faster penetration and improved control with handheld Drilling Machines. Material Suitability and Tip Geometry Benefits The 135° tip angle is engineered for drilling into harder workpieces such as alloyed and unalloyed steels, cast steel and cast iron. A larger tip angle shortens the initial centering phase and reduces walking when starting the hole, so fewer pilot operations are needed. As a Type N drill with a Normal Spiral, it is tailored for metalworking tasks while maintaining acceptable regrinding properties for workshop sharpening. Shank Design and Practical Handling Equipped with a Cylindrical Shank, this twist drill fits conventional three-jaw chucks and allows quick tool changes without specialized adapters. The robust shank form provides universal compatibility, making the drill a practical choice for repair shops and assembly lines using standard chucks. Users should note that for extremely high torque demands, alternate shank types may reduce the risk of slippage. Applications, Efficiency and Target Users This drill excels for technicians, maintenance professionals and craftsmen who require reliable, repeatable metal drilling, including sheet metal, profiles and harder plastics. The DIN 1897 conformity ensures predictable dimensions for production contexts. For those who value speed and reduced operator fatigue, the combination of HSS‑G metallurgy and short geometry achieves up to 40% faster drilling with notably less feed force compared to conventional HSS drills. Highly recommended: the MetavCUT Twist Drill (Type N) for precise metalworking — for tailored advice or technical clarification contact METAV Werkzeuge at info@metav-werkzeuge.com, call +49 2822 7131930 or WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 56050-FDA Diameter: 5 mm Tip angle: 135° Execution: Extra short Colour: Bright finished Material: HSS-G Standard: DIN 1897 Shank: Cylindrical Total length: 62 mm Spiral length: 26 mm Type: Type N Application: Drills for metal Model series: Standard Line Intended machine: Drilling Machine (Hand Drill) Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill (Type N) best used for? The MetavCUT Twist Drill (Type N) is primarily intended for metalworking applications; it is used for drilling alloyed and unalloyed steel, cast steel, cast iron and hard plastics, offering robust performance in demanding machining tasks. For what is a Twist Drill used? A Twist Drill is mainly used for machining high‑strength materials and larger drill diameters; its form is easy to resharpen and endures higher loads, making it suitable for professional metalwork. Which three drill types exist? Typical drill categories are metal drills, wood drills and stone/concrete drills, each optimised for material‑specific cutting geometry and flute design. Why are twist drills sharpened at the tip? The sharpening reduces the cross‑edge at the drill tip, lowering friction so that less feed force is required and the tip centres more accurately in the workpiece. Can a metal twist drill be used to drill wood? A metal (HSS) drill can be used in wood but will have reduced guidance and a less clean finish compared with a dedicated wood drill; however, they are easier to resharpen and have a lower tendency to self‑feed. For which drilling depths is the twist drill the most used tool? A twist drill is the typical choice for drilling through solid stock; it is most commonly used for diameters up to 20 mm and depths up to 100 mm.

Spiralbohrer HSS-G 6,5 mm, 135°, Typ N, extra kurz, blank, DIN 1897 Der Spiralbohrer ist ein extra kurzer HSS-G-Bohrer für präzise Metallbohrungen mit hoher Stabilität in Handbohrmaschinen. Extra kurze Ausführung für beengte Einbausituationen HSS-G-Material für langlebige Schnittkante 135° Spitzenwinkel für härtere Werkstoffe Zylinderschaft: universell einspannbar im Dreibackenfutter DIN 1897 Norm für verlässliche Standardlänge und Qualität Robuste Schneidkante für effizientes Bohren in Stahl und Guss Der geschliffene HSS-G-Werkstoff sorgt für eine hohe Verschleißfestigkeit und eine langlebige Schneidkante, sodass der Bohrer auch bei wiederholten Einsätzen seine Leistung behält. Durch den 135° Spitzenwinkel dringt die Schneide leichter in härtere Werkstoffe ein, was die Anbohrzeit reduziert und Ausschuss minimiert. Dieser Vorteil macht den Bohrer zur wirtschaftlichen Wahl für Arbeiten in legiertem Stahl, Gussstahl und Temperguss, ohne aufwendige Nachbearbeitung. Kurze Bauform erhöht Stabilität und reduziert Bruchrisiko Die extra kurz ausgeführte Bauform verringert die Hebelwirkung und erhöht die Verdrehungsfestigkeit gegenüber längeren Ausführungen, was besonders bei Handgeführten Maschinen wichtig ist. In Kombination mit der kompakten Spirallänge wird die Späneförderung bei flachen Bohrungen optimiert, wodurch weniger Verkantungen auftreten. Anwender profitieren von höherer Präzision und einer deutlich geringeren Bruchneigung, speziell bei dünnen Blechen und Profilen. Passgenau für den Alltag: Handbohrmaschine, Profile und Bleche Dieser Bohrer richtet sich an Handwerker, Monteure und Hobbyanwender, die regelmäßig Metall bearbeiten und dabei auf unkomplizierte, universelle Lösungen setzen. Die Zylinderschaft ermöglicht das Einspannen in normale Dreibackenfutter und vereinfacht den Wechsel zwischen Maschinen. Für Anwendungen in Nichteisenmetallen und Hartkunststoff bietet der Bohrer saubere Ausfräsungen; bei Edelstahl und sehr harten Werkstoffen empfiehlt sich angepasste Schnittgeschwindigkeit und Kühlung. Hinweise zur Anwendung und Vorteile der Normausführung Die Fertigung nach DIN 1897 garantiert reproduzierbare Maße und erleichtert die Planung in Werkstatt und Produktion. Die kompakte Standard Line Ausführung ist besonders geeignet für Vorbohrungen und Reparaturarbeiten, bei denen Raum begrenzt ist. Durch die Kombination aus Materialwahl, Spitzengeometrie und Kurzlänge wird ein bis zu 40 % schnelleres Bohren sowie eine geringere Anpresskraft erreicht, wodurch Ermüdung beim Arbeiten reduziert und die Effizienz gesteigert wird. Empfehlung: Für präzise Metallbohrungen die MetavCUT Standard Line nutzen und bei technischen Fragen die kompetente Beratung von METAV Werkzeuge in Anspruch nehmen – per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930, auch per WhatsApp +49 170 2837271 erreichbar Technische Daten Bezeichnung: Spiralbohrer Marke: MetavCUT SKU: 56065-FDA Durchmesser: 6,5 mm Spitzenwinkel: 135° Typ: Typ N Material: HSS-G Ausführung: extra kurz Farbe: blank Schaftausführung: Zylinder Gesamtlänge: 70 mm Spirallänge: 31 mm Norm: DIN 1897 Für Bohrmaschine: Handbohrmaschine Modellserie: Standard Line Verpackungseinheit: 10 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Ist der Spiralbohrer von MetavCUT für Edelstahl geeignet? Der Spiralbohrer von MetavCUT (Typ N) mit 135° Spitzenwinkel ist für härtere Werkstoffe wie Edelstahl geeignet, sofern die Schnittgeschwindigkeit reduziert und Kühlung eingesetzt wird, um Überhitzung und vorzeitigen Verschleiß zu vermeiden. Kann der extra kurze Bohrer in einer Handbohrmaschine verwendet werden? Ja, der extra kurz ausgeführte Spiralbohrer ist speziell für den Einsatz in Handbohrmaschinen vorgesehen und bietet durch die reduzierte Länge erhöhte Stabilität bei Handanwendung. Welchen Vorteil bietet die Zylinderschaft beim Spiralbohrer MetavCUT? Die Zylinderschaft des Spiralbohrers erlaubt das einfache Einspannen in gängige Dreibackenfutter, was den schnellen Werkzeugwechsel und die universelle Einsetzbarkeit im Alltag erleichtert. Warum ist die Norm DIN 1897 wichtig für diesen Bohrer? Die Herstellungsweise nach DIN 1897 gewährleistet definierte Maßhaltigkeit und Kompatibilität mit Einspannungen und Bohrprozessen, wodurch Planbarkeit und Ersatzteilmanagement in Werkstätten verbessert werden. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#56065-FDA","sku":"56065-FDA","mpn":"56065-FDA","name":"Spiralbohrer 6,5 mm Typ N extra kurz","description":"Spiralbohrer HSS-G 6,5 mm, 135°, Typ N, extra kurz, blank, DIN 1897. Extra kurze Ausführung für beengte Einbausituationen; HSS-G-Material für langlebige Schneidkante; 135° Spitzenwinkel für härtere Werkstoffe; Zylinderschaft universell einspannbar im Dreibackenfutter; geeignet für Handbohrmaschine und Arbeiten in Stahl, Guss und Nichteisenmetallen.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741b/logo-metav-1200-1200.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741e/logo-metav-1200-900.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png"],"additionalProperty":[{"@type":"PropertyValue","name":"Bezeichnung","value":"Spiralbohrer"},{"@type":"PropertyValue","name":"Durchmesser","value":"6,5 mm"},{"@type":"PropertyValue","name":"Spitzenwinkel","value":"135°"},{"@type":"PropertyValue","name":"Typ","value":"Typ N"},{"@type":"PropertyValue","name":"Farbe","value":"blank"},{"@type":"PropertyValue","name":"Ausführung","value":"extra kurz"},{"@type":"PropertyValue","name":"Norm","value":"DIN 1897"},{"@type":"PropertyValue","name":"Material","value":"HSS-G"},{"@type":"PropertyValue","name":"Schaftausführung","value":"Zylinder"},{"@type":"PropertyValue","name":"Gesamtlänge","value":"70 mm"},{"@type":"PropertyValue","name":"Spirallänge","value":"31 mm"},{"@type":"PropertyValue","name":"Für Bohrmaschine","value":"Handbohrmaschine"},{"@type":"PropertyValue","name":"Modellserie","value":"Standard Line"},{"@type":"PropertyValue","name":"Verpackungseinheit","value":"10"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"Ist der Spiralbohrer von MetavCUT für Edelstahl geeignet?","acceptedAnswer":{"@type":"Answer","text":"Der Spiralbohrer MetavCUT 6,5 mm Typ N ist für härtere Werkstoffe wie Edelstahl geeignet, wenn die Schnittgeschwindigkeit reduziert und Kühlung eingesetzt wird, um Überhitzung und vorzeitigen Verschleiß zu vermeiden."}},{"@type":"Question","name":"Kann der extra kurze Spiralbohrer in einer Handbohrmaschine verwendet werden?","acceptedAnswer":{"@type":"Answer","text":"Ja, der extra kurz ausgeführte Spiralbohrer MetavCUT ist speziell für den Einsatz in Handbohrmaschinen konzipiert und bietet durch die reduzierte Länge erhöhte Stabilität bei Handanwendung."}},{"@type":"Question","name":"Welchen Vorteil bietet die Zylinderschaft beim Spiralbohrer MetavCUT?","acceptedAnswer":{"@type":"Answer","text":"Die Zylinderschaft des Spiralbohrers MetavCUT erlaubt das einfache Einspannen in gängige Dreibackenfutter, was schnellen Werkzeugwechsel und universelle Einsetzbarkeit erleichtert; bei sehr hohem Drehmoment kann er allerdings eher durchrutschen als 3‑Kant‑Schaftvarianten."}},{"@type":"Question","name":"Warum ist die Norm DIN 1897 wichtig für diesen Bohrer?","acceptedAnswer":{"@type":"Answer","text":"Die Fertigung nach DIN 1897 gewährleistet definierte Maßhaltigkeit und Kompatibilität mit Einspannungen und Bohrprozessen, was Planbarkeit und Ersatzteilmanagement in Werkstätten verbessert."}}]},{"@type":"ItemPage","url":"https://metav-shop.de","dateModified":"2026-05-04T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Spiralbohrer HSS-G"},{"@type":"Thing","name":"Standard Line"},{"@type":"Thing","name":"Bohrer für Metall"}],"mentions":[{"@type":"Thing","name":"Zylinderschaft"},{"@type":"Thing","name":"DIN 1897 Norm"},{"@type":"Thing","name":"135° Spitzenwinkel"},{"@type":"Thing","name":"Extra kurz Bauform"}]}]}

Spiralbohrer 6 mm · 135° · Typ N · blank · extra kurz · DIN 1897 · HSS-G · MetavCUT Der Spiralbohrer ist ein extra kurzer HSS-G Metallbohrer für Handbohrmaschinen, optimiert für stabile, platzbegrenzte Bohrarbeiten in Stahl, Guss und Nichteisenmetallen. Extra kurze Bauform für mehr Stabilität HSS-G für erhöhte Verschleißfestigkeit 135° Spitze reduziert Anbohrzeit in harten Werkstoffen Zylinderschaft für universelle Aufnahme im Bohrfutter Normgerechte Ausführung nach DIN 1897 Mehr Stabilität bei beengten Platzverhältnissen Die extra kurze Bauform reduziert Hebelwirkung und Verdrehung, wodurch die Bruchneigung deutlich sinkt. Das macht den Bohrer ideal für Arbeiten in engen Bereichen oder bei kurzen Spannwegen. Anwender profitieren von einer höheren Standzeit und weniger Nacharbeit, weil die Bohrung zentrierter erfolgt und das Werkzeug ruhiger in der Aufnahme läuft. Diese Konstruktion eignet sich besonders für dünnwandige Bleche und Profile, wo Präzision und Stabilität entscheidend sind. Effizientes Bohren in harten Werkstoffen Dank HSS-G und dem 135° Spitzenwinkel dringt der Bohrer kontrollierter in legierte und unlegierte Stähle ein. Der Typ N mit Normalspirale bietet gute Spanabfuhr bei Metallbearbeitung und ist auf den rauen Einsatz abgestimmt. Für Anwender bedeutet das weniger Kraftaufwand beim Anbohren und eine zuverlässige Spanbildung, wodurch die Bohrgeschwindigkeit erhöht und Werkzeugverschleiß reduziert wird. Die Kombination liefert konstante Ergebnisse bei Standard-Metallanwendungen. Universelle Aufnahme und praktische Abmessungen Der Zylinderschaft ermöglicht schnelles Einspannen in gängige Dreibackenfutter von Handbohrmaschinen. Mit einer Gesamtlänge von 66 mm und einer Spirallänge von 28 mm bleibt der Bohrer handlich und kompakt, ohne Komfort beim Bohren zu verlieren. Die Norm DIN 1897 garantiert Austauschbarkeit und Maßhaltigkeit. Anwender in Werkstatt und Montage schätzen die einfache Handhabung und die Kompatibilität mit gängigen Maschinen. Für wen dieser Bohrer entwickelt wurde Entwickelt für Profi-Handwerker und anspruchsvolle Heimwerker, die stabile, zuverlässige Bohrungen in Metall erwarten. Das Werkzeug eignet sich für Montage, Maschinenbau-Reparaturen und allgemeine Werkstattarbeiten, bei denen kurze, präzise Bohrungen gefragt sind. Durch die robuste Materialwahl und die kurze Bauform liefert der Bohrer beständige Leistung, ohne spezielle Maschinen vorauszusetzen. Empfehlung: Setzen Sie auf die bewährte Robustheit und Präzision des HSS-G Spiralbohrers von MetavCUT; bei Fragen oder für persönliche Beratung erreichen Sie METAV Werkzeuge per eMail unter info@metav-werkzeuge.com oder telefonisch unter +49 2822 7131930 Bezeichnung: Spiralbohrer Marke: MetavCUT SKU: 56060-FDA Durchmesser: 6 mm Spitzenwinkel: 135° Typ: Typ N Material: HSS-G Ausführung: extra kurz Farbe: blank Norm: DIN 1897 Gesamtlänge: 66 mm Spirallänge: 28 mm Schaftausführung: Zylinder Anwendung: Bohrer für Metall Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Ist der Spiralbohrer von MetavCUT für Edelstahl geeignet? Der MetavCUT Spiralbohrer Typ N mit 135° Spitzenwinkel ist für härtere Werkstoffe wie Edelstahl besser geeignet als Bohrer mit flacherer Spitze; er bietet kontrolliertes Eindringen und stabile Spanbildung bei Edelstahlbearbeitung. Kann der Spiralbohrer in einer Handbohrmaschine verwendet werden? Ja, der Spiralbohrer von MetavCUT ist für den Einsatz in Handbohrmaschinen vorgesehen; durch seine extra kurze Bauform wird die Stabilität erhöht, wobei auf rutschfestes Einspannen im Zylinderschaft zu achten ist. Welche Vorteile bringt das HSS-G Material beim Spiralbohrer? Das HSS-G Material des MetavCUT Spiralbohrers gewährleistet erhöhte Verschleißfestigkeit und Wärmebeständigkeit, was zu längeren Standzeiten und konstanter Bohrleistung in legierten und unlegierten Stählen führt. Wofür eignet sich die extra kurze Ausführung besonders? Die extra kurze Ausführung des MetavCUT Spiralbohrers ist ideal für Bohrungen in dünnwandigen Bauteilen und beengten Arbeitsbereichen, da sie Verdrehung reduziert und die Bruchgefahr verringert. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#56060-FDA","sku":"56060-FDA","mpn":"56060-FDA","name":"Spiralbohrer 56060-FDA","description":"Spiralbohrer 6 mm, 135°, Typ N, blank, extra kurz, DIN 1897, HSS-G; extra kurze Bauform für hohe Stabilität bei beengten Platzverhältnissen; geeignet für Handbohrmaschinen und Metallbearbeitung.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741b/logo-metav-1200-1200.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741e/logo-metav-1200-900.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png"],"additionalProperty":[{"@type":"PropertyValue","name":"Bezeichnung","value":"Spiralbohrer"},{"@type":"PropertyValue","name":"Durchmesser","value":"6 mm"},{"@type":"PropertyValue","name":"Spitzenwinkel","value":"135°"},{"@type":"PropertyValue","name":"Typ","value":"Typ N"},{"@type":"PropertyValue","name":"Farbe","value":"blank"},{"@type":"PropertyValue","name":"Ausführung","value":"extra kurz"},{"@type":"PropertyValue","name":"Norm","value":"DIN 1897"},{"@type":"PropertyValue","name":"Material","value":"HSS-G"},{"@type":"PropertyValue","name":"Schaftausführung","value":"Zylinder"},{"@type":"PropertyValue","name":"Gesamtlänge","value":"66 mm"},{"@type":"PropertyValue","name":"Spirallänge","value":"28 mm"},{"@type":"PropertyValue","name":"Anwendung","value":"Bohrer für Metall"},{"@type":"PropertyValue","name":"Hersteller","value":"MetavCUT"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"Ist der Spiralbohrer von MetavCUT für Edelstahl geeignet?","acceptedAnswer":{"@type":"Answer","text":"Der Spiralbohrer 6 mm von MetavCUT (Typ N, HSS-G, 135°) ist für härtere Werkstoffe wie Edelstahl besser geeignet als Bohrer mit flacherem Spitzenwinkel; er bietet kontrolliertes Eindringen und stabile Spanbildung."}},{"@type":"Question","name":"Kann der Spiralbohrer in einer Handbohrmaschine verwendet werden?","acceptedAnswer":{"@type":"Answer","text":"Ja, der Spiralbohrer 6 mm von MetavCUT ist für Handbohrmaschinen vorgesehen; die extra kurze Bauform erhöht die Stabilität, das Einspannen im Zylinderschaft sollte rutschfest erfolgen."}},{"@type":"Question","name":"Welche Vorteile bringt das HSS-G Material beim Spiralbohrer?","acceptedAnswer":{"@type":"Answer","text":"Das HSS-G Material des Spiralbohrers 6 mm von MetavCUT gewährleistet erhöhte Verschleißfestigkeit und Wärmebeständigkeit, was zu längeren Standzeiten und konstanter Bohrleistung in legierten und unlegierten Stählen führt."}},{"@type":"Question","name":"Wofür eignet sich die extra kurze Ausführung besonders?","acceptedAnswer":{"@type":"Answer","text":"Die extra kurze Ausführung des Spiralbohrers 6 mm von MetavCUT ist ideal für Bohrungen in dünnwandigen Bauteilen und beengten Arbeitsbereichen, da sie Verdrehung reduziert und die Bruchgefahr verringert."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/spiralbohrer-56060-FDA","dateModified":"2026-05-04T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Spiralbohrer Standard Line"},{"@type":"Thing","name":"Extra kurze Bauform für beengte Platzverhältnisse"},{"@type":"Thing","name":"HSS-G Bohrer nach DIN 1897"}],"mentions":[{"@type":"Thing","name":"Zylinderschaft für universelle Aufnahme"},{"@type":"Thing","name":"135° Spitzenwinkel für härtere Werkstoffe"},{"@type":"Thing","name":"Anwendung in Handbohrmaschinen"}]}]}