End gauges for precise length calibration
End gauges provide exact reference lengths for calibrating measurement instruments and ensuring consistent dimensional accuracy in metalworking and inspection processes. Used in production and laboratory settings, these end gauges—made from steel, ceramic or carbide—allow technicians to compensate for wear and thermal effects and maintain measurement traceability, especially when employed alongside parallel end gauges, cylinder gauges and calibration masters. Classes 0, 1 and 2 define practical tolerance levels for workshop, inspection-room and production use respectively, delivering the repeatable precision required for machining and quality control.
0.5 mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
Take advantage of ceramic material and Grade 1 (DIN 861/1) accuracy to secure reproducible reference points in inspection and calibration tasks; the compact 0.5 mm nominal size and minimal mass make this gauge block simple to handle and integrate into inspection routines. Order direct via Metav Werkzeuge or consult our specialists for application advice. Ceramic gauge block 0.5 mm — Grade 1 precision for calibration (Metav IndustryLine) Ceramic gauge block 0.5 mm, Grade 1 DIN 861/1 is a compact reference element for precision measurement and calibration in metrology environments, suited for setting and checking small-length standards. Ceramic body for excellent thermal stability Grade 1 accuracy according to DIN 861/1 Nominal size 0.5 mm for calibration checks Lightweight 1 g for easy handling Reliable reference for routine calibration and micro-measurements The compact 0.5 mm reference block provides a stable datum for short-range calibration tasks and verification of micrometrology instruments. Made from ceramic, the block exhibits low thermal expansion compared with many metals, which reduces measurement drift when ambient temperature varies; this stability directly improves repeatability in day‑to‑day checks. As a Grade 1 standard under DIN 861/1, the part is intended for professional inspection use where tolerances are tight but routine handling and interchangeability remain priorities. The small form factor and negligible mass make it straightforward to position in fixtures and gauge sets without introducing significant handling artefacts. Designed to support traceable workflows and efficient inspection routines Integrating a compact ceramic reference aids lean metrology processes: the small nominal size and consistent surface finish speed up comparison checks and minimise setup time. The physical properties of the material contribute to long service life and reduced wear, which lowers the frequency of replacements and preserves calibration intervals. Where quick verification of precision tools or bench instruments is required, this reference element serves as a dependable short-length standard that complements broader gauge block sets, easing routine quality control without overcomplicating procedures. Clear specification and shop-floor applicability The product is supplied with manufacturer identification and clear numerical data that simplify documentation and inventory control. Its Grade 1 designation and conformity to DIN 861/1 provide a recognised benchmark for procurement and quality records; this helps maintain consistency across inspection activities and supports compliance with internal quality systems. Because the piece is lightweight and compact, it is particularly useful in metrology labs, toolrooms and production inspection stations where small standards are needed frequently and must be stored and retrieved without disrupting workflows. Contact Metav Werkzeuge GmbH for tailored advice on integrating this ceramic gauge block into measurement systems and to arrange procurement via Metav Werkzeuge; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M324.000.5 GTIN: 4054469142265 Label: Keramik-Endmaß 0,5 mm, Güte 1 DIN 861/1 Facts Nominal size: 0.5 mm Weight: 0.001 kg Customs tariff number: 90173000 Grade: 1 Special features Material: Ceramic Standard: DIN 861/1 eClass: 21170108 Category path: Messgeräte › Endmasse FAQ What level of accuracy does this gauge block provide? The ceramic gauge block is specified as Grade 1 under DIN 861/1, making it suitable for professional inspection tasks that require tight tolerances and consistent repeatability. Is the material appropriate for temperature‑sensitive measurements? Ceramic construction gives the block low thermal expansion compared with many metals, so the gauge block maintains dimensional stability when ambient temperature varies during short-range checks. Can this reference be used daily on the shop floor? Yes, the compact 0.5 mm size and light mass make the ceramic reference well suited for frequent handling and routine verification in toolrooms and inspection benches. How is the product identified for inventory and traceability? Identification is provided via the article number M324.000.5 and GTIN 4054469142265, which should be recorded in calibration and quality documentation for traceability. Which applications are typical for such a small gauge block? Typical uses include calibration checks of micrometrology instruments, setting up small-length standards and verifying short comparators where a stable short reference is needed. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
0.5 mm Gauge Block, Grade 0, DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine
Take advantage of Grade 0 accuracy, the DIN EN ISO 3650 conformity and a hardened special-steel finish for a stable, repeatable reference in precision measurement—order the gauge block directly via Metav Werkzeuge or consult the Metav team for application advice. Gauge block 0.5 mm (DIN EN ISO 3650) — Grade 0, hardened special steel Gauge block 0.5 mm serving as a compact, high-precision reference standard for workshop and laboratory measurement tasks Grade 0 tolerance for laboratory precision Conforms to DIN EN ISO 3650 standard Hardened special steel for long-term stability Guaranteed reference accuracy for calibration points The gauge block 0.5 mm is manufactured to DIN EN ISO 3650, delivering a Grade 0 tolerance that suits calibration tasks and high-precision inspection. As a reference element, it provides a defined nominal length with minimal deviation, ensuring reliable comparative measurements when used in gauge stacks or as a single standard. The compact nominal size makes it particularly useful where very small, traceable references are required; its specification aligns with established metrology practice so measurement uncertainty can be quantified and documented. Robust material and geometry for consistent results Constructed from hardened special steel, this block resists wear and preserves the finished length across repeated uses. The cross-section for sizes up to 10 mm is 30 x 9 mm, providing a stable contact area while keeping mass and thermal inertia low. The combination of a hardened surface and a compact geometry reduces the risk of plastic deformation and maintains flatness and parallelism under normal workshop handling. These material choices translate into fewer rework cycles and a dependable standard for daily quality control routines. Clear conformity and practical traceability Compliance with DIN EN ISO 3650 makes this product suitable for integration into a documented measurement system and for inclusion in calibration routines. The nominal dimension and the Grade 0 classification make the block a suitable master for lab-grade checks and intercomparisons. Where formal traceability is required, the defined standard and marking enable straightforward recording in quality documentation and support audit processes, helping to keep measurement chains transparent and defensible. Compact format for precision tasks and workshop economy The small nominal length minimises thermal drift and simplifies handling when assembling gauge stacks for fine adjustments. With a mass of approximately 0.003 kg and a reduced profile, the block is easy to position and pair with other standards or instruments. For workshops aiming to balance precision and efficiency, the block serves as an accessible reference that complements broader calibration sets while reducing the need for oversized masters in routine checks. Contact Metav Werkzeuge GmbH in Emmerich for tailored guidance on using Metav IndustryLine gauge blocks and for support in selecting the right reference standards for specific metrology tasks Technical data Article number: M319.005.0 GTIN: 4054469129921 Tariff number: 90173000 Nominal size: 0.5 mm Standard: DIN EN ISO 3650 Grade: 0 Facts Weight: 0.003 kg Cross-section: up to 10 mm — 30 x 9 mm Special features Material: hardened special steel Category: gauge block / end gauge Intended use: reference standard for precision measurement FAQ What tolerance class does this gauge block meet? The gauge block meets Grade 0 tolerance as specified in DIN EN ISO 3650, offering laboratory-level accuracy suitable for calibration and precision inspection. Is the material suitable for long-term use in a workshop environment? Yes. The block is made from hardened special steel, which provides wear resistance and dimensional stability for repeated use in workshop and inspection settings. Can this block be used as a stand-alone reference for fine adjustments? Yes. With a nominal size of 0.5 mm and a compact cross-section, this gauge block is well suited for fine adjustments and integration into gauge stacks for precise setting tasks. What is the article number for ordering and documentation? The article number is M319.005.0, which should be quoted for orders, inventory, and calibration records relating to this gauge block. Does the product conform to an internationally recognised standard? It conforms to DIN EN ISO 3650, making it appropriate for systems that require standard-compliant reference measures. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
0.5 mm Gauge Block, Grade 1, DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine
Take advantage of a Grade 1 reference gauge made from hardened special steel and manufactured to DIN EN ISO 3650 for repeatable dimensional checks; the compact cross‑section ensures stable handling in inspection routines. Order the End gauge 0.5 mm directly via Metav Werkzeuge or ask the consultants for further technical information. End gauge 0.5 mm — Grade 1 reference to DIN EN ISO 3650 (Metav IndustryLine) The End gauge 0.5 mm is a precision reference used for dimensional verification in laboratory and workshop inspection, suitable where a traceable, repeatable small nominal measure is required DIN EN ISO 3650 grade 1 accuracy Hardened special steel for long life Nominal size 0.5 mm precision reference Cross-section 30 x 9 mm for stable handling Reliable reference for routine inspection The gauge serves as a compact, traceable reference for verification tasks where a stable nominal length is essential. Manufactured to DIN EN ISO 3650 and specified as Grade 1, this reference provides defined tolerances that support consistent quality control and inspection routines. The nominal measure of 0.5 mm is suitable for setting up comparative checks, validating measuring fixtures and confirming the performance of comparators. Where reproducible results are required, the defined standard and grade ensure measurable conformity rather than subjective judgement. Durable construction that maintains accuracy Constructed from special steel, hardened, the gauge is designed for long service life under normal workshop conditions. The compact cross‑section (up to 10 mm → 30 x 9 mm) gives a stable profile that resists twisting during handling, which reduces the risk of incidental deformation. As a result, calibration intervals can be planned with confidence and the reference remains a dependable element in an inspection set. The robust material choice and heat treatment contribute directly to dimensional stability and wear resistance. How it integrates into inspection workflows As a small nominal reference, the gauge fits naturally into bench and go/no‑go comparisons, tool setting and verification stages. Its slim format allows integration into gauge blocks, fixtures and set-ups where space is limited; handling is simplified by the stable cross‑section. Documentation practices benefit from the Grade 1 classification because inspection records can reference an established standard. For users seeking to align shop‑floor checks with laboratory traceability, this reference complements existing metrology equipment and supports transparent quality processes. For reliable small‑measure references and advice on integrating this Grade 1 gauge into inspection procedures, contact Metav Werkzeuge for availability and technical guidance: info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: M319.005.1 GTIN: 4054469129938 SKU: M319.005.1 Label: End gauge 0.5 mm, DIN ISO 3650, Grade 1 Facts Nominal size: 0.5 mm Quality grade: 1 Weight: 0.003 kg Tariff number: 90173000 Cross-section: up to 10 mm → 30 x 9 mm; from 10.1 mm → 35 x 9 mm Special features Material: special steel, hardened Standard: DIN EN ISO 3650 Category: End gauges FAQ What is the primary use of this end gauge? The end gauge 0.5 mm is intended as a precision reference for dimensional verification, serving comparative checks, tool setting and routine inspection tasks where a small, stable nominal length is required. Which standard and grade apply to this reference? Manufactured to DIN EN ISO 3650, the item is specified as Grade 1, providing an established tolerance class for routine metrology documentation and traceable inspection procedures. What material and design features ensure durability? The gauge is made from special steel, hardened, with a compact cross‑section (30 x 9 mm for sizes up to 10 mm) that improves resistance to handling stresses and helps maintain dimensional stability. Can this gauge be used in laboratory and shop environments? Yes; the Grade 1 classification and hardened construction make the gauge suitable for both laboratory calibrations and shop‑floor verification routines where reproducibility is required. How is the product identified for ordering and inventory? The product is listed as SKU M319.005.1 (GTIN 4054469129938) under the Metav IndustryLine range and appears in the End gauges category for measuring instruments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.0 mm Gauge Block Grade 0, DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine
The combination of DIN EN ISO 3650 precision, Grade 0 tolerance and a hardened special steel construction ensures a stable, traceable reference for calibration tasks; benefit from consistent contact surfaces and minimal thermal drift. Order the end gauge directly via Metav Werkzeuge or consult our technical advisors for integration into inspection routines. End Gauge 1.0 mm (DIN EN ISO 3650, Grade 0) — Single gauge block with hardened steel The End Gauge 1.0 mm (DIN EN ISO 3650, Grade 0) is a compact single gauge block designed as a precision reference for dimensional inspection and calibration in laboratories and workshop metrology. Gauge block, DIN EN ISO 3650 Grade 0 Hardened special steel construction Nominal size 1.0 mm reference standard Compact cross-section for stable handling Reference accuracy for reliable calibration As a DIN EN ISO 3650 Grade 0 reference, this single end gauge delivers the reproducible dimensional baseline expected in calibration chains and quality checks. The 1.0 mm nominal size functions as a primary transfer standard for setting instruments, verifying indicators and assembling gauge stacks. Its classification as Grade 0 implies tight manufacturing tolerances suitable for laboratory use and high-standard workshop inspections, supporting traceable measurement processes and repeatable results. Material stability and handling that support repeatability Manufactured from hardened special steel, the gauge block resists wear and maintains flatness over time, reducing the need for frequent reconditioning. The compact cross‑section (30 × 9 mm for sizes up to 10 mm) provides a stable contact area that is easy to position and read, while the low mass aids careful manual handling. These material and design choices minimise contact deformation and thermal effects, which in turn improves the reproducibility of comparative measurements and setting procedures. Practical integration into quality workflows This single gauge block is supplied as a discrete reference part with a clear article identity (SKU M319.010.0), making it straightforward to catalogue and include in inspection routines. As a precision reference standard, it complements calipers, micrometers and indicator setups, serving both as a check artefact and as a building block for gauge stacks. Specifying a recognised norm such as DIN EN ISO 3650 simplifies conformity documentation and supports consistent quality assurance across departments and suppliers. Choose the Metav IndustryLine End Gauge 1.0 mm via Metav Werkzeuge for dependable dimensional references; contact our experts at info@metav-werkzeuge.com or call +49 2822 7131930 for tailored technical guidance Technical Data Article number: M319.010.0 GTIN: 4054469129945 Label: Einzel-Endmaß 1,0 mm, DIN ISO 3650, Güte 0 DIN ISO 3650 Standard: DIN EN ISO 3650 Facts Nominal size: 1.0 mm Weight: 0.003 kg Cross-section: 30 x 9 mm (for sizes ≤ 10 mm) Tolerance grade: 0 Customs tariff number: 90173000 Special features Material: Special steel, hardened Category: End gauge (single gauge block) Application: Reference standard for dimensional inspection and calibration SKU: M319.010.0 FAQ What level of accuracy does this gauge deliver? The End Gauge 1.0 mm conforms to DIN EN ISO 3650 in Grade 0, providing the narrow tolerances expected of a laboratory-grade reference for calibration and inspection. Is the material specified for long-term use? Yes. The unit is made from hardened special steel, selected to preserve flatness and resist wear during repeated contact and stacking. How is the gauge identified for inventory and traceability? The gauge is supplied with SKU M319.010.0 and GTIN 4054469129945, facilitating catalogue management and traceability within quality systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.0 mm Gauge Block Grade 1 DIN EN ISO 3650 Hardened Special Steel - Metav IndustryLine
Take advantage of DIN EN ISO 3650 conformity and Grade 1 accuracy together with a hardened special‑steel design for a compact, reproducible reference. Order the gauge block directly via Metav Werkzeuge or request advice from our consultants for integration into inspection routines. Gauge block 1.0 mm — Grade 1 reference (DIN EN ISO 3650) | Metav IndustryLine The gauge block 1.0 mm is a precision reference intended for calibration, dimensional verification and comparison work in metrology laboratories and quality‑control benches DIN EN ISO 3650 certified accuracy Hardened special steel construction Compact 1.0 mm reference gauge Engineered precision for traceable measurement As a Grade 1 reference produced to DIN EN ISO 3650, this block delivers the level of precision expected for routine calibration and comparative inspection. The nominal 1.0 mm dimension serves as a stable master for setting micrometres, vernier callipers and comparator fixtures, enabling consistent repeatability across multiple checks. Compliance with the recognised standard supports quality documentation and inspection planning in regulated production environments. Robust construction for repeatable results Manufactured from hardened special steel, the block resists wear from repeated wringing and handling, which maintains dimensional integrity over time. The compact cross‑section for sizes up to 10 mm is 30 x 9 mm, giving a practical balance between handability and stiffness; this geometry reduces the likelihood of distortion during use and simplifies positioning in gauge nests or comparator clamps. Practical format for workshop and laboratory use With a mass of 0.003 kg and a small footprint, the reference is convenient for bench work and rapid set‑ups while remaining stable when wrung or clamped. Identification and traceability are supported by the supplied identifiers such as GTIN 4054469129952 and SKU M319.010.1, which aid inventory control and record keeping. The block’s design suits daily comparison tasks and calibration routines where a compact, repeatable master is required. Integration into a dependable metrology workflow Choosing a standardized Grade 1 reference reduces uncertainty in routine measurements and shortens inspection cycles through faster set‑up and fewer rechecks. Combined with Metav’s role as a precision partner, this reference contributes to reliable measurement processes and predictable production quality, backed by a broad product range and logistical support from Emmerich. For supply, technical advice or to discuss suitable reference sets from Metav IndustryLine, contact Metav Werkzeuge for personalised support: info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: M319.010.1 Designation: End gauge 1.0 mm, DIN EN ISO 3650, Grade 1 GTIN: 4054469129952 SKU: M319.010.1 Standard: DIN EN ISO 3650 Material: Special steel, hardened Facts Nominal dimension: 1 mm Weight: 0.003 kg Cross section (≤10 mm): 30 x 9 mm Customs tariff number: 90173000 Special features Grade 1 accuracy for routine calibration Compact master for comparators and calliper setting Category: End gauges / gauge blocks Manufacturer brand: Metav IndustryLine FAQ What tolerance class does this reference meet? The gauge block meets Grade 1 tolerance requirements according to DIN EN ISO 3650, providing a dependable standard for everyday calibration tasks. Is the material suitable for long‑term use in a workshop environment? Yes, the block is made from hardened special steel, which offers wear resistance suited to regular wringing and handling typical in workshop and laboratory settings. Which dimensions and identifiers are provided for traceability? The reference carries the nominal 1.0 mm designation, SKU M319.010.1 and GTIN 4054469129952 to support inventory and documentation workflows. Can this block be combined with other gauges for comparative checks? The compact geometry and standard form factor make this block suitable for combination with other gauge blocks or comparator setups as a stable reference element. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.0005 mm Gauge Block Grade 0, Hardened Special Steel, DIN EN ISO 3650 - Metav IndustryLine
Take advantage of Grade 0 accuracy, a nominal size of 1.0005 mm and a hardened special steel construction for reliable reference measurements; order the gauge block directly via Metav Werkzeuge or consult our specialists for precision tooling advice. Single-end gauge block 1.0005 mm — Grade 0, DIN EN ISO 3650 (Metav IndustryLine) The single-end gauge block 1.0005 mm is a precision reference standard for calibration and inspection tasks in workshops and metrology labs, complying with DIN EN ISO 3650 for dimensional traceability. Grade 0 accuracy to DIN EN ISO 3650 Nominal size 1.0005 mm Hardened special steel construction Compact cross-section for fine handling Trusted reference for calibration and quality control A reference standard with Grade 0 tolerance provides the base for repeatable calibration routines and batch inspections. The block’s nominal size of 1.0005 mm is manufactured to the tight geometrical and surface requirements of DIN EN ISO 3650, ensuring compatibility with industry calibration procedures. For quality managers and inspection technicians, this translates into a verifiable reference that minimises drift between measuring instruments and supports documented conformity during audits. Robust material and stable geometry for consistent results Made from hardened special steel, the block resists wear and maintains stable dimensions under normal handling and environmental conditions. The specified cross-section (up to 10 mm: 30 x 9 mm; from 10.1 mm: 35 x 9 mm) balances rigidity with ease of manipulation, enabling precise positioning on comparators, micrometres or gauge tables. The small mass and compact shape reduce the risk of handling-induced measurement error, supporting reproducible reference readings in routine workflows. Clear numerical data for metrology planning Key numerical properties of this reference element facilitate immediate integration into inspection plans and certificates. The documented nominal size 1.0005 mm, combined with the DIN EN ISO 3650 conformity and the low unit weight, allows straightforward specification in measurement procedures, tolerance chains and calibration schedules. Purchasing and inventory decisions benefit from unambiguous data that fit standardised quality-management documentation. Practical use and care in the workshop environment The design supports careful handling and short-term storage in protective holders: the compact geometry eases placement between anvils or on flat reference surfaces. Routine care—gentle cleaning with approved solvents and storage in a dry case—preserves the block’s reference condition. When included in a set of reference standards, the single-end block serves as a stable primary element for verifying small gaps, setting gauges and cross-checking digital or mechanical measuring equipment. Choose Metav IndustryLine gauge blocks for dependable Grade 0 references; contact Metav Werkzeuge for ordering and technical guidance on integrating this gauge block into existing calibration procedures. Technical data Article number: M319.010005.0 GTIN: 4054469129969 Weight: 0.003 kg Category: Endmasse Facts Nominal size: 1.0005 mm Standard: DIN EN ISO 3650 Grade: 0 Tariff number: 90173000 Materials & special features Material: Hardened special steel Cross-section: up to 10 mm: 30 x 9 mm; from 10.1 mm: 35 x 9 mm Product type: Single-end gauge block FAQ What is the intended use of this single-end gauge block? The single-end gauge block 1.0005 mm is intended as a precision reference for calibration, inspection and the verification of length-measuring instruments in metrology and workshop environments. Does the block comply with international standards? Yes, the block is manufactured to DIN EN ISO 3650 and supplied in Grade 0, making it suitable for standardised calibration procedures and traceable measurement routines. Which materials can affect the block during use or storage? The block is made of hardened special steel; avoid aggressive chemicals and humid storage. Gentle cleaning and dry, cushioned storage preserve dimensional stability. Can this gauge block be used to calibrate comparators and micrometres? Yes. Its nominal size of 1.0005 mm and Grade 0 tolerance make it suitable as a reference for comparators, micrometres and other small-gap measuring devices. Is the cross-section suitable for precision handling? The compact cross-section (30 x 9 mm up to 10 mm nominal size) supports fine handling and stable seating on reference surfaces, aiding repeatable measurements. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.0005 mm Gauge Block Grade 1, Hardened Special Steel, DIN EN ISO 3650 - Metav IndustryLine
Benefit from Grade 1 accuracy and a 1.0005 mm nominal size in a hardened special steel reference that supports reproducible calibration and reliable inspection results; order the gauge block directly via Metav Werkzeuge or consult our specialists for application advice. Gauge block 1.0005 mm — DIN EN ISO 3650, Grade 1 by Metav IndustryLine Gauge block 1.0005 mm (DIN EN ISO 3650) is a compact dimensional reference intended for calibration and high-precision inspection tasks in metrology and quality control. Grade 1 accuracy (DIN EN ISO 3650) Hardened special steel construction Nominal size 1.0005 mm for high precision Compact 30 x 9 mm cross-section for stable contact Precision that underpins repeatable measurements The Gauge block 1.0005 mm is manufactured to DIN EN ISO 3650 tolerances and Grade 1 quality, providing a reliable reference for comparative and verification measurements. Its nominal dimension of 1.0005 mm positions it as a micro reference in calibration sets and bench standards, where small deviations can affect machine set‑up and final part acceptance. The adherence to the ISO standard ensures manufacturers and labs can rely on defined tolerance classes when documenting measurement capability and uncertainty. Stable geometry and material for consistent contact Constructed from hardened special steel, the block combines surface hardness with a compact profile of 30 x 9 mm, delivering a stable contact face and low susceptibility to bending. With a lightweight form factor (approx. 0.003 kg) and a cross-section optimised for secure holding, the component offers consistent seating during stacking and comparison. These qualities reduce variability in reference chains and make the block suitable for precision benches and calibration sets where consistent geometry directly improves process efficiency. Practical integration into calibration and inspection workflows As a physical reference, this end measure supports quick checks and set‑ups in incoming inspection, tool calibration and laboratory routines, shortening adjustment times and improving first‑pass yields. The block’s traceable specification to DIN EN ISO 3650 simplifies documentation for audits and quality records. Combined with Metav IndustryLine’s focus on accessible precision, the element is a pragmatic choice for workshops and metrology labs aiming to raise measurement reliability without complex integration efforts. Choose Metav IndustryLine’s Grade 1 gauge block for dependable dimensional references — contact Metav Werkzeuge for procurement details and expert guidance from Emmerich to ensure seamless integration into existing calibration routines Technical data Article number: M319.010005.1 GTIN: 4054469129976 SKU: M319.010005.1 Facts Nominal size: 1.0005 mm Weight: 0.003 kg Cross-section: 30 x 9 mm Grade: 1 Special features Material: hardened special steel Standard: DIN EN ISO 3650 Tariff number: 90173000 FAQ What accuracy class does this gauge block have? The gauge block is manufactured to Grade 1 in accordance with DIN EN ISO 3650, ensuring tight tolerances suitable for precision calibration. What is the nominal size and cross-section of the block? The nominal dimension is 1.0005 mm and the cross-section for this size is 30 x 9 mm, providing a compact and stable contact surface. Which material is used for the reference block? This reference is made from hardened special steel, chosen for its dimensional stability and wear resistance in routine calibration use. How is the block best used in a calibration set? The block serves as a small reference element for stacking and comparison within a set of gauge blocks or for direct verification of measuring instruments and fixtures. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.0005mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
The combination of ceramic construction, grade 1 accuracy to DIN 861/1 and the nominal length of 1.0005 mm ensures a thermally stable reference for high-precision length comparisons; order the gauge block via Metav Werkzeuge or consult our specialists for application advice. Ceramic gauge block 1.0005 mm, grade 1 DIN 861/1 — Metav IndustryLine reference Ceramic gauge block 1.0005 mm, grade 1 DIN 861/1 is a high-stability reference element for dimensional inspection and calibration in precision workshops and inspection labs. Ceramic material for thermal stability Grade 1 accuracy to DIN 861/1 Nominal length 1.0005 mm for reference measurements Reliable reference for precision checks This ceramic gauge block serves as a stable length standard for comparative measurements and setup tasks. With a nominal length of 1.0005 mm and grade 1 tolerance per DIN 861/1, the block is intended for tasks that demand reproducible dimensional references rather than routine rough checks. The low thermal expansion of the ceramic base minimises length changes with ambient temperature, so the block maintains its stated value during short handling and measuring cycles. For workshops that require consistent reference points for calipers, micrometers and gauges, a ceramic reference reduces drift and supports repeatable setup routines. Material advantages explained for everyday use The choice of ceramic provides intrinsic benefits over metallic references: superior thermal stability, good wear resistance in light-contact applications, and electrical insulation where needed. These properties translate into longer intervals between reconditioning and fewer length deviations during normal use. As a grade 1 element, the block balances precision and robustness, making it suitable for quality-control benches and toolroom checks where traceable, repeatable standards are required. The compact design and small mass also reduce the risk of inadvertent thermal loading when handled. Practical role in a metrology workflow A gauge block of this specification is most useful as a calibrated reference for comparative measurement, master-setting of micrometers and verification of measuring instruments. Used properly with wringing techniques and clean contact faces, the block helps to establish reliable master lengths on which other tools can be referenced. In addition, its format allows it to be combined with other blocks when establishing stacks or stepped references, offering flexibility without compromising the base accuracy. For laboratories and precision workshops seeking to standardise measurement routines, this element is a useful, stable building block in measurement chains. For assistance choosing the right Metav IndustryLine ceramic gauge block for a specific application, or to arrange technical consultation, please contact Metav Werkzeuge directly at info@metav-werkzeuge.com or by phone on +49 2822 7131930 — our specialists in Emmerich will advise on fit and handling Technical data Article number: M324.001.00A GTIN: 4054469142371 eCl@ss: 21170108 Core measurements Nominal length: 1.0005 mm Accuracy class: Grade 1 (DIN 861/1) Weight: 0.001 kg Tariff number: 90173000 Materials & features Material: Ceramic Category: Gauge block / end measure Intended use: Dimensional reference and inspection FAQ What accuracy class does this gauge block meet? The Ceramic gauge block 1.0005 mm, grade 1 DIN 861/1 meets grade 1 accuracy as defined in DIN 861/1, making it suitable for demanding reference and inspection tasks. Can this ceramic gauge block be used for setting micrometers and calipers? Yes, the gauge block is intended as a stable reference for setting micrometers and calipers; its 1.0005 mm nominal length and ceramic construction provide a reliable master for comparative adjustments. Is the material suitable for environments with temperature variations? The ceramic material offers low thermal expansion compared with many metals, improving dimensional stability during short-term exposure to normal workshop temperature fluctuations. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.001 mm Gauge Block Grade 0, DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine
Take advantage of Grade 0 accuracy and the DIN EN ISO 3650 compliance together with a hardened special-steel construction for a stable, repeatable reference standard; order directly via Metav Werkzeuge or consult our specialists for procurement advice. Gauge block 1.001 mm — Grade 0 reference, DIN EN ISO 3650 A gauge block 1.001 mm designed as a laboratory-grade length standard for calibration benches and precision workshops Grade 0 accuracy to DIN EN ISO 3650 Precision nominal size 1.001 mm Hardened special steel for stability Compact cross-section 30 × 9 mm Laboratory-grade accuracy for reliable reference measurements The Grade 0 classification, certified to DIN EN ISO 3650, ensures a high level of dimensional fidelity that serves as a dependable reference in both calibration and quality control workflows. With a nominal size of 1.001 mm, this single gauge block is intended for use where sub-millimetre traceability is required. The conformity to an international standard provides a verifiable basis for measurement chains, making the block suitable as a master standard on a calibration bench or as a reference artefact for setting up inspection equipment. The clear standard reference reduces uncertainty in comparative measurements and supports consistent quality documentation. Robust construction that limits wear and thermal influence Manufactured from hardened special steel, the block combines surface hardness with dimensional stability across routine handling. The compact 30 × 9 mm cross-section used for sizes up to 10 mm offers a favourable stiffness-to-size ratio, which helps to keep mechanical deformation and surface wear low during stacking and wringing operations. Its low mass also minimises thermal drift during short exchanges on the bench. These material and geometric choices translate into longer service life for the reference element and fewer reconditioning cycles, supporting uninterrupted measurement routines in the workshop or laboratory. Practical role in calibration routines and precision assembly As a single reference element, this block is suitable for direct comparison tasks, length-setting operations and stack-based gauge chains. The modest size and nominal value make it an efficient building block for creating composite lengths or verifying small-gap dimensions in precision assemblies. Because the entry specifies DIN EN ISO 3650 compliance and Grade 0, the element can be integrated into a traceable calibration workflow or used as part of a set for routine checks on handheld instruments and bench-mounted comparators. The compact footprint eases storage and handling while preserving the functional benefits of a high-quality reference standard. For laboratory-grade reference standards from Metav IndustryLine, contact Metav Werkzeuge to discuss delivery options and technical details — Metav Werkzeuge is available at info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical data Article number: M319.01001.0 GTIN: 4054469129983 Category: Measuring instruments / Gauge blocks Core technical data Nominal size: 1.001 mm Cross-section: 30 × 9 mm Weight: 0.003 kg Customs tariff number: 90173000 Special features Material: Hardened special steel Standard: DIN EN ISO 3650, Grade 0 Single gauge block FAQ What accuracy class does this block meet? The gauge block meets Grade 0 requirements according to DIN EN ISO 3650, offering high-precision performance suitable for reference measurements. What material is used for the block? The block is made from hardened special steel, chosen for dimensional stability and wear resistance during wringing and stacking. Which cross-section applies to this size? For nominal sizes up to 10 mm the cross-section is 30 × 9 mm, which applies to this 1.001 mm element. Is this block suitable as a laboratory reference? Given the Grade 0 classification and DIN EN ISO 3650 conformity, this block is suitable for use as a laboratory-level reference within calibration chains. Does the product entry indicate a supplied calibration certificate? The provided product data does not specify a calibration certificate for this gauge block Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.001 mm Gauge Block Grade 1, Hardened Special Steel, DIN EN ISO 3650 - Metav IndustryLine
Take advantage of a DIN EN ISO 3650 Grade 1 reference gauge with a nominal size of 1.001 mm, crafted from hardened special steel for reproducible Go/No‑Go checks; order the gauge directly via Metav Werkzeuge or contact our consultants for specification advice. End gauge 1.001 mm (M319.01001.1) — DIN EN ISO 3650, Grade 1 The End gauge 1.001 mm is a hardened special‑steel reference gauge designed for precise dimensional checks in inspection and quality‑control applications. DIN EN ISO 3650, Grade 1 Nominal size 1.001 mm precision Hardened special steel design Compact cross-section 30 x 9 mm Accurate reference for routine inspection benches A stable reference is essential for fast, reliable quality control. This grade‑1 end gauge provides a nominal size of 1.001 mm with the material stability needed for frequent use; the combination of a hardened alloy and compact geometry reduces thermal and mechanical drift during short‑term checks. As a result, technicians obtain repeatable Go/No‑Go decisions without prolonged setup, increasing throughput in production and final inspection. Compact construction with durable materials The gauge is manufactured from hardened special steel, offering corrosion‑resistant surface properties and long service life under regular handling. For nominal sizes up to 10 mm the specified cross‑section is 30 x 9 mm, which keeps the gauge rigid while remaining easy to position in fixtures or between measuring faces. Minimal mass and a refined finish reduce the risk of damage to mating parts and support stable contact conditions during dimensional verification. Straightforward integration into quality workflows Designed as a workshop reference, this gauge simplifies acceptance testing and daily checks. Traceability is supported by the clear marking and the supplied article code M319.01001.1, facilitating inventory and measurement records. The robust design makes it suitable for handheld checks, fixture mounting and use alongside optical or mechanical comparators. Where speed of decision and conformity to standards matter, this reference tool reduces ambiguity and helps maintain production tolerances. For traceable precision from Metav IndustryLine, contact Metav Werkzeuge GmbH in Emmerich for technical advice and reliable supply of the M319.01001.1 end gauge Technical Data Article number: M319.01001.1 GTIN: 4054469129990 Nominal size: 1.001 mm Standard: DIN EN ISO 3650 Grade: 1 Facts Nominal size: 1.001 mm Weight: 0.003 kg Cross-section: 30 x 9 mm Tariff code: 90173000 Special features Material: special steel, hardened Category: End gauges Intended use: reference gauge for dimensional inspection Manufacturer: Metav IndustryLine FAQ What is the exact nominal size and tolerance of this gauge? The nominal size is 1.001 mm and the gauge conforms to DIN EN ISO 3650, Grade 1, providing a precision reference for routine checks. Which material is used for the gauge and how does it affect durability? The tool is made from hardened special steel, which ensures wear resistance and dimensional stability during regular inspection tasks. How should the gauge be used in a production environment? Use the end gauge for quick Go/No‑Go verifications, fixture checks and routine dimensional controls; the compact cross‑section and hardened finish support rapid, repeatable comparisons. Is the item identified for traceability and stock management? Yes — the article is listed as M319.01001.1 and carries GTIN 4054469129990 for inventory and traceability purposes. What cross‑section applies to this nominal size? For sizes up to 10 mm the applicable cross‑section is 30 x 9 mm, providing a balance of rigidity and accessibility. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.002 mm Gauge Block Grade 0, Hardened Special Steel, DIN EN ISO 3650 - Metav IndustryLine
Take advantage of the combination of DIN EN ISO 3650 conformity, Grade 0 tolerance and a hardened special steel construction to secure repeatable length standards in precision workflows; order this single gauge block directly via Metav Werkzeuge or consult the sales team for integration advice. Single gauge block 1.002 mm — precision end measure, Metav IndustryLine, DIN EN ISO 3650 Grade 0 Single gauge block 1.002 mm is a compact, certified length standard designed for high-accuracy measurements in workshops and calibration contexts, suitable as a reference or as part of a precision block set. DIN EN ISO 3650, Grade 0 Nominal length 1.002 mm Hardened special steel construction Compact cross-section 30×9 mm Consistent accuracy for traceable length standards The 1.002 mm single gauge block is manufactured to DIN EN ISO 3650 and specified as Grade 0, making it appropriate where tight geometric tolerances and reproducible length references are needed. The defined tolerance class ensures that the block can serve as a reliable length standard in comparative checks, machine set‑ups and quality control routines. By using a standardised reference produced to this norm, measurement uncertainty is reduced through conformity to an internationally recognised specification, supporting process consistency and documentation. Durable material and handling advantages Constructed from hardened special steel, the block offers a stable surface hardness that minimises wear during repeated use and reduces the risk of dimensional change over time. The compact 30×9 mm cross-section for sizes up to 10 mm provides good accessibility when assembling or separating stacks, while still offering sufficient contact area for secure seating. This material choice combines long-term durability with predictable thermal behaviour, helping to keep calibration drift low in normal workshop conditions and ensuring a long service life for the reference. Practical integration into calibration and inspection The end measure functions well as an individual standard or as part of a matched set for stack measurements and comparative verification. Its format supports precise seating and repeatable contact conditions, which simplifies routine checks and minimises operator-induced variation. Wherever reproducible reference lengths are required — from incoming goods inspection to in‑process verification — the block supplies a compact, standard-compliant solution that integrates into existing calibration procedures with minimal adaptation. Documentation of the standard and its specification facilitates traceability in quality records. For precision measurement tasks that demand standard-compliant references, choose the Metav IndustryLine single gauge block and contact Metav Werkzeuge in Emmerich for supply and configuration assistance Technical data Article number: M319.01002.0 GTIN: 4054469130002 Nominal length: 1.002 mm Standard: DIN EN ISO 3650 Tolerance grade: 0 Specifications Weight: 0.003 kg Cross-section: 30×9 mm Tariff number: 90173000 eClass: 21170108 Materials and features Material: Hardened special steel Application: End measure for length standards Category: End mass / gauge block FAQ What accuracy can be expected from this gauge block? The single gauge block 1.002 mm is manufactured to DIN EN ISO 3650 Grade 0, providing a tolerance level appropriate for high‑precision comparative work and routine quality checks. Is a calibration certificate supplied with the block? The product description does not indicate a supplied calibration certificate by default; calibration services can be arranged separately to meet traceability requirements for the single gauge block 1.002 mm. How should the block be handled to maintain its accuracy? Handle the block with clean, dry gloves and avoid contact with unprotected surfaces; ensure consistent contact conditions when seating the block to reduce operator-induced variation and preserve the hardened measuring faces. Can this block be used in a stacked set for intermediate lengths? Yes, the compact cross‑section and precise nominal length make the block suitable for stacking with other blocks to obtain intermediate reference lengths while maintaining repeatability. What environments are suitable for use of this gauge block? Use in controlled workshop or calibration-laboratory conditions is recommended; avoid prolonged exposure to aggressive chemicals or extreme temperatures to preserve dimensional stability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.002 mm Gauge Block Grade 1 DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine
Combine DIN EN ISO 3650 Grade 1 accuracy with hardened special steel for a compact, reliable reference gauge; order the gauge directly via Metav Werkzeuge or ask our consultants for application advice. Gauge block 1.002 mm (DIN EN ISO 3650, Grade 1) — hardened special steel The Gauge block 1.002 mm is a precision end standard designed for calibration, stack building and reference measurements in metrology laboratories and workshop inspection stations. DIN EN ISO 3650, Grade 1 accuracy Nominal size 1.002 mm for precision stacks Hardened special steel construction Compact 30 x 9 mm cross-section Dependable reference for calibration and inspection Built to the DIN EN ISO 3650 specification and manufactured to Grade 1, this precision end standard delivers a stable single-length reference of 1.002 mm suitable for stack building, verification of micrometers and calibration routines. The defined nominal size provides a deterministic element for dimensional check routines and helps to reduce cumulative uncertainty when combined into gauge stacks. The compliance with an established standard supports traceable documentation and routine quality checks. Durable construction that keeps accuracy over time The body is made from hardened special steel, giving high surface hardness and wear resistance while preserving flatness and parallelism. The compact cross-section of 30 x 9 mm (applicable for sizes up to 10 mm) aids handling and positioning in tight assemblies and makes the block convenient for use in small fixtures. The material choice limits abrasion during repeated use and contributes to long service life under normal laboratory and workshop conditions. Designed for practical integration into metrology workflows This precision end standard is optimised for rapid incorporation into existing inspection procedures: its nominal size and robust finish make it suitable for building traceable stacks and for verifying measuring instruments. Identifiers such as the GTIN and SKU support inventory control and traceability within quality systems, while the low mass simplifies handling in manual procedures. For specialised stacks or automated measuring cells, the block serves as a compact, stable datum element that complements broader calibration schemes. Choose the Metav IndustryLine gauge block for reliable reference measurements and contact Metav Werkzeuge in Emmerich for tailored advice at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: M319.01002.1 GTIN: 4054469130019 SKU: M319.01002.1 Tariff number: 90173000 Facts Nominal size: 1.002 mm Weight: 0.003 kg Cross-section: 30 x 9 mm Grade: 1 Special features Material: special steel, hardened Standard: DIN EN ISO 3650 Intended use: end measure / gauge block for calibration and stack building FAQ What level of accuracy does this gauge block offer? The gauge block 1.002 mm is manufactured to Grade 1 under DIN EN ISO 3650, providing the dimensional stability and repeatability expected for reference and inspection tasks. Can this block be used in gauge stacks for length setting? Yes. The nominal 1.002 mm length and compact cross-section make this end standard suitable for building precise gauge stacks and for fine adjustments in calibration routines. What material is the block made from and why does that matter? The block is made from hardened special steel, which offers wear resistance and dimensional stability, ensuring the reference length remains reliable over many cycles of use. Is the product traceable within a quality management system? Traceability is supported via identifiers such as the GTIN and SKU; the block is listed as M319.01002.1 (Metav IndustryLine) for inventory and documentation purposes. For which environments is this gauge block intended? This end standard is intended for controlled metrology and workshop inspection environments where a compact, stable reference of 1.002 mm is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.002mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
Benefit from the Grade 1 accuracy of this ceramic reference and the dimensional stability of a 1.002 mm nominal length to secure repeatable calibration results; order the gauge block directly via Metav Werkzeuge or consult our specialists for application advice. Ceramic Gauge Block 1.002 mm, Grade 1 (DIN 861/1) — Metav IndustryLine The ceramic gauge block 1.002 mm serves as a compact, high‑stability reference for precision length measurement and calibration tasks in laboratory and inspection environments. Grade 1 accuracy according to DIN 861/1 Ceramic material for thermal stability Reference length: 1.002 mm, traceable GTIN Precision where it matters The Grade 1 designation under DIN 861/1 identifies this element as a fine reference standard suitable for calibration benches and laboratory comparisons. With a nominal length of 1.002 mm, the block functions as a stable length standard for comparative measurements, plug‑gauging and assembly verification. The classification indicates industrial‑grade manufacturing and strict quality control, giving engineers and technicians a clear basis for metrological decisions and traceable documentation. Stability for reproducible measurements Constructed from ceramic, this gauge block offers low thermal expansion and strong wear resistance compared with common metal standards, which reduces drift under changing ambient conditions. The material choice supports reproducible results during short transfer intervals between measuring instruments and inspection stations. The compact format and lightweight design make it convenient to integrate into routine checks and calibration sets without introducing unnecessary handling error. Built for calibration and quality workflows Designed as a reference element in quality control, the block complements dimensional control routines and standard sets. Its compact dimensions are beneficial for precise stacking and combination with other blocks to achieve target lengths. Identification via GTIN and the SKU M324.001.002 simplifies inventory and traceability in documented calibration cycles, while the concise specification supports procurement and technical planning across workshops and metrology departments. For procurement guidance or tailored measurement advice contact Metav Werkzeuge in Emmerich to discuss the Metav IndustryLine ceramic gauge block M324.001.002 and its fit for existing calibration programmes Technical Data Article number: M324.001.002 GTIN: 4054469142296 Material: Ceramic Nominal length: 1.002 mm Grade: 1 (DIN 861/1) Weight: 0.001 kg Tariff number: 90173000 Facts Category: Measuring instruments — Gauge blocks Label: Keramik-Endmaß 1,002mm, Güte 1 DIN 861/1 Manufacturer: Metav IndustryLine Special features Ceramic construction for low thermal expansion Compact reference element for calibration Traceable identification via GTIN and SKU FAQ What tolerance class does this gauge block meet? The gauge block meets Grade 1 tolerance as specified by DIN 861/1, making it suitable for precision reference tasks in inspection and calibration. Is the material suitable for temperature‑sensitive measurements? Yes, the ceramic construction provides low thermal expansion and good dimensional stability for use in environments where temperature control is important. How is the block identified for inventory and traceability? Identification is provided by the SKU M324.001.002 and the GTIN 4054469142296, which support cataloguing and traceable calibration records. Can this element be combined with other gauge blocks? The block is designed for use within gauge‑block stacks to achieve target lengths for calibration and measurement setups. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.002mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
Take advantage of the ceramic construction and the Grade 1 manufacturing standard (DIN 861/1) to secure a stable, wear-resistant length artefact for laboratory and inspection work; order the Ceramic gauge block directly via Metav Werkzeuge or consult our product specialists for application advice. Ceramic gauge block 1.002 mm — Grade 1 DIN 861/1 (Metav IndustryLine) A ceramic gauge block 1.002 mm designed as a compact, thermally stable length standard for precision calibration and inspection tasks Ceramic material for thermal stability Grade 1 tolerance according to DIN 861/1 Nominal length 1.002 mm for precision standards GTIN registered; tariff no. 90173000 Stable material for repeatable measurements This length artefact combines the inherent thermal stability of ceramic with a Grade 1 finish to reduce variation caused by temperature swings and surface wear. The combination results in a gauge block that maintains dimensional integrity during repeated use and stacking, helping to lower measurement uncertainty in routine checks. The ceramic body is naturally resistant to corrosion and abrasion, making it a reliable choice for production and metrology environments where repeatability is essential. Supports reliable calibration and workflow efficiency As a compact length standard, the block is designed to integrate into calibration routines and reference stacks without adding handling complexity. Its geometry and finish simplify mating with other standards, which shortens setup time and improves throughput in quality-control processes. By using a Grade 1 block that conforms to DIN 861/1, laboratories and inspection stations can rely on a consistent reference point that supports faster decisions and fewer rechecks. Easy storage and lasting performance The minimal mass and robust ceramic surface contribute to comfortable handling and long service life. Small, precise artefacts like this are easy to store safely and clean without specialised consumables. The wear resistance of the material reduces the need for frequent replacement, supporting predictable maintenance cycles and lower lifecycle costs for calibration sets. Ideal for calibration labs and precision workshops This block serves calibration laboratories, toolrooms and precision-engineering workshops that require compact, high-quality length standards for verification and instrument checks. Where sub-millimetre references are needed to validate fine measurements or to build accurate gauge stacks, the block offers a practical combination of precision, stability and durability that suits routine lab use and periodic audits. Contact Metav Werkzeuge today to discuss the Grade 1 Ceramic gauge block — delivery and technical advice are available from our Emmerich location to ensure fit-for-purpose selection and supply. Technical data Article number: M324.001.001 GTIN: 4054469142289 Material: Ceramic Nominal length: 1.002 mm Grade: 1 (DIN 861/1) Manufacturer: Metav IndustryLine Weight: 0.001 kg Facts ECLASS: 21170108 Tariff number: 90173000 SKU: M324.001.001 Special features Label: Keramik-Endmaß 1,002mm, Güte 1 DIN 861/1 Category: Measuring instruments > Gauge blocks Corrosion resistant ceramic surface Compact length artefact for stacking FAQ What accuracy standard does this block meet? The Ceramic gauge block 1.002 mm is manufactured to Grade 1 in accordance with DIN 861/1, providing a high-quality reference surface for calibration and inspection. Is the ceramic material suitable for regular laboratory use? Yes, the ceramic composition used in the gauge block offers low thermal expansion and good abrasion resistance, making it well suited for repeated use in calibration labs and inspection routines. Can this block be used in gauge block stacks? The block's nominal length and Grade 1 finish make it appropriate for inclusion in stacked references and transfer standards where compact, precise increments are required. What identifiers are provided for traceability? Traceability is supported by the GTIN 4054469142289 and tariff number 90173000, recorded for inventory and customs purposes. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.003 mm Gauge Block Grade 1, DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine
Benefit from consistent, laboratory-grade measurement and durable construction: the nominal 1.003 mm size combined with DIN EN ISO 3650 Grade 1 accuracy supports repeatable calibration routines and reliable reference chains. Order the gauge directly via Metav Werkzeuge or contact our advisors for specification checks and delivery options. End gauge 1.003 mm (DIN EN ISO 3650), Grade 1 — Metav IndustryLine A precision End gauge 1.003 mm designed as a calibration standard for dimensional verification and reference measurement in metrology labs and quality control environments. Hardened special steel for wear resistance Conforms to DIN EN ISO 3650, Grade 1 accuracy Nominal dimension 1.003 mm for precise calibration Reliability for calibration programmes and production control The block serves as a compact calibration standard with a nominal dimension of 1.003 mm, enabling straightforward verification of micrometre and calliper performance. Supplied in a single nominal size, this reference piece reduces setup time during routine checks and supports traceable measurement chains. The adherence to DIN EN ISO 3650 and classification as Grade 1 ensures the block provides the dimensional stability required in laboratory and workshop calibration intervals, helping to maintain measurement integrity across repeated use. Durable design for frequent handling and long service life Manufactured from hardened special steel, the gauge block is engineered to resist surface wear and mechanical abrasion during regular use. The compact cross-section for small nominal sizes (30 x 9 mm for dimensions up to 10 mm) gives a robust feel without unnecessary bulk, easing manual handling and storage. This robustness translates into lower replacement rates and predictable lifetime performance, which supports efficiency and cost control in quality management systems. Clear benefits for quality assurance workflows Using a standardised reference block simplifies compliance with internal inspection plans and external audits by providing an immediate, verifiable standard for dimensional checks. The block’s physical properties make it suitable for direct comparison measurements and for establishing reference points in gauge sets. Because the piece is a Grade 1 block, it is appropriate for precision tasks where a compact, stable master standard is required rather than the ultra-fine resolutions reserved for specialised laboratory artefacts. Practical integration with existing metrology equipment The small form factor of this reference piece allows straightforward integration into existing calibration benches and toolboxes. It can be used alongside comparators, dial indicators and optical measurement devices for quick verification sequences. The modest mass and compact footprint make handling simple and reduce the likelihood of user-induced error during exchange; repeatability of results is thereby enhanced in everyday inspection work. Documentation and identification for inventory control The gauge is provided with a unique article number (SKU) and GTIN for unambiguous identification within stores and calibration records, facilitating inventory management and traceability. Clear labelling supports record-keeping for calibration cycles and audit trails, which is essential for regulated production environments and for businesses that rely on documented metrology practices to prove conformity. Secure this Grade 1 reference from Metav IndustryLine — contact Metav Werkzeuge for tailored advice and assured supply from Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M319.01003.1 GTIN: 4054469130033 Manufacturer: Metav IndustryLine Facts Nominal dimension: 1.003 mm Mass: 0.003 kg Tariff number: 90173000 Special features Material: Special steel, hardened Standard: DIN EN ISO 3650 Grade: 1 Cross-section (≤ 10 mm): 30 x 9 mm Category: End gauges FAQ What applications are suitable for this end gauge? This end gauge is suitable for calibration tasks, dimension verification and reference measurements in metrology labs and production quality control; the Grade 1 block provides a compact, stable standard for these uses. Is the dimension traceable to a recognised standard? The block is manufactured to DIN EN ISO 3650 and supplied with identifiers (SKU and GTIN) to support traceability and record-keeping for calibration programmes. What material is the gauge made from and why does that matter? The gauge is made of hardened special steel, which provides surface durability and resistance to wear, helping to maintain dimensional stability during frequent handling. Can this block be used for routine workshop checks on calipers and micrometres? Yes. The nominal 1.003 mm reference is ideal for routine verification of small-range instruments, offering a quick and reliable reference for everyday calibration tasks. How is the product identified for inventory and quality records? Identification is via the article number M319.01003.1 and GTIN 4054469130033, which supports systematic documentation in inspection logs and calibration certificates. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.003 mm Gauge Block, Accuracy Grade 0, Hardened Special Steel, DIN EN ISO 3650 - Metav IndustryLine
Combine Grade 0 accuracy with DIN EN ISO 3650 conformity and a hardened special steel construction for a dependable laboratory reference; order this single gauge block directly via Metav Werkzeuge or consult our specialists for application advice. Single gauge block 1.003 mm — Grade 0, DIN EN ISO 3650 (Metav IndustryLine) The Single gauge block 1.003 mm serves as a precision reference standard for dimensional calibration and inspection in metrology laboratories and quality-control departments. Grade 0 accuracy to DIN EN ISO 3650 Hardened special steel for wear resistance Nominal length 1.003 mm, high repeatability Consistent, standard-compliant accuracy for traceable checks The block delivers Grade 0 accuracy in accordance with DIN EN ISO 3650, providing a reliable reference for calibration tasks and comparative measurements. With a nominal length of 1.003 mm, this precision element is suitable for establishing short-length standards and verifying high-resolution instruments. The adherence to the DIN EN ISO 3650 standard means measurement results are comparable across laboratories and tooling setups, supporting process control and quality assurance workflows. Durable material and compact geometry for everyday use Manufactured from hardened special steel, the gauge block resists wear and maintains dimensional stability under regular handling. The compact cross-section of 30 × 9 mm (applicable for nominals up to 10 mm) offers a convenient balance between gripability and thermal mass, reducing the effect of rapid temperature changes during short checks. These construction choices extend service life and support reproducible contact conditions when used with flat reference surfaces or in stack assemblies. Practical handling and integration into calibration routines Designed as a reference element for short-range verification, the block integrates easily into measuring setups, master sets or comparator checks. Gentle use of wringing techniques and clean contact surfaces enhances repeatability; the block functions well within laboratory sequences where consistent reference lengths are required. For procurement, technical queries or bespoke set composition, contact options are available through Metav Werkzeuge, who combine broad supply capacity with expert advice for workshop and laboratory integration. For laboratory-grade references choose Metav IndustryLine’s single gauge block 1.003 mm — contact Metav Werkzeuge in Emmerich for technical guidance and fast supply. Technical data Article number: M319.01003.0 GTIN: 4054469130026 Standard: DIN EN ISO 3650 Grade: 0 Category: Endmasse Facts Nominal size: 1.003 mm Weight: 0.003 kg Cross-section: 30 × 9 mm Customs tariff number: 90173000 Special features Material: Special steel, hardened Intended use: Precision reference / dimensional calibration Manufacturer: Metav IndustryLine SKU: M319.01003.0 FAQ What level of accuracy does Grade 0 offer? Grade 0 denotes a high-precision tolerance band defined by DIN EN ISO 3650; the single gauge block 1.003 mm meets that grade and is suitable as a short-length reference in calibration tasks. Is the block supplied with a calibration certificate? Calibration is not specified in the product data for the single gauge block 1.003 mm; customers may request calibration services and certificates through Metav Werkzeuge to match their traceability requirements. How should the gauge block be handled to ensure longevity? Handle the block with clean, dry hands or gloves, keep contact faces free of debris and use proper wringing or storage techniques; the hardened special steel construction helps maintain dimensional stability under careful use. Can this gauge block be used in set assemblies or comparators? Yes, the single gauge block 1.003 mm is designed as a precision reference element and can be combined into master sets or employed in comparator and inspection routines. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.003mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
Benefit from Grade 1 DIN 861/1 accuracy combined with a wear‑resistant ceramic construction for a stable, repeatable reference standard; these properties support consistent dimensional checks and long service life. Order the gauge block through Metav Werkzeuge or consult the Metav specialists if further selection guidance is required. Ceramic gauge block 1.003 mm — Grade 1 reference gauge (Metav IndustryLine) The Ceramic gauge block 1.003 mm is a compact reference standard designed for temperature‑stable dimensional checks and comparator set‑ups in calibration workshops and metrology labs. Grade 1 accuracy per DIN 861/1 Ceramic material for thermal stability Precision nominal size 1.003 mm Compact, low mass reference gauge Dependable reference for routine and comparative checks The grade 1 classification according to DIN 861/1 signifies a workplace‑grade reference suitable for precise comparative tasks in quality control. As a single‑dimension reference with a 1.003 mm nominal size, the block serves reliably in comparator chains, slip‑gauge stacks and for quick verification of micrometre or caliper calibration. The clear standardisation under DIN provides a familiar benchmark for engineers and technicians, helping to shorten inspection cycles while retaining measurability and traceability within shop‑floor procedures. Ceramic construction that stabilises measurements Made from ceramic, this reference exhibits low thermal expansion and high wear resistance, properties that reduce dimensional drift during handling and measurement. Ceramic gauge blocks are non‑magnetic and resist corrosion, which preserves the reference surface and minimises the need for frequent resurfacing or replacement. Together, these features help to maintain reproducible contact conditions when wringing or when used with optical comparators, so that repeat measurements remain within expected scatter for workshop standards. Practical handling and integration into inspection routines The low mass and compact size of this gauge block make it convenient for rapid checks and for inclusion in portable inspection kits. Careful handling is required: surfaces must be clean and free from oil or particulates before wringing to ensure proper contact and accurate stacking. When used as part of a reference set, the block supports straightforward verification of gauges, micrometres and other dimensional instruments, serving as a stable baseline for daily quality control. Its compact form also facilitates secure storage and reduces thermal gradients during short measurement sequences. Long‑term value through stability and repeatability Investing in a ceramic reference block reduces the frequency of replacement due to surface wear and helps preserve calibration intervals. The combination of 1.003 mm nominal accuracy and ceramic robustness supports consistent measurement results across repeated cycles, which in turn contributes to predictable inspection throughput and reduced rework. For operations seeking a compact, durable standard that integrates easily with existing measurement chains, this reference offers a cost‑efficient way to raise routine precision without complex handling procedures. For precise selection advice or to order the Ceramic gauge block 1.003 mm from Metav IndustryLine, contact Metav Werkzeuge in Emmerich for specialist guidance and reliable supply by phone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com. Technical data SKU: M324.001.003 GTIN: 4054469142302 Material: Ceramic Nominal size: 1.003 mm Grade: 1 (DIN 861/1) Weight: 0.001 kg Customs tariff number: 90173000 Facts Nominal dimension: 1.003 mm Grade designation: 1 Mass: 0.001 kg GTIN: 4054469142302 Tariff code: 90173000 Special features Material properties: ceramic (low thermal expansion, corrosion resistant) Category: Gauge block / End measure Intended use: reference standard for comparative measurements Manufacturer: Metav IndustryLine FAQ What tolerance class does this gauge block conform to? The Ceramic gauge block 1.003 mm is specified as Grade 1 under DIN 861/1, providing the reference classification commonly used for workshop and inspection‑level comparative measurements. Is the material suitable for use in temperature‑controlled laboratories? Yes, the ceramic construction of the gauge block reduces thermal expansion compared with many metals, improving dimensional stability during short‑term measurement sequences typical in labs and calibration benches. Can this block be wrung to other gauge blocks or standards? The reference is suitable for conventional wringing practices common to gauge‑block handling; ensuring clean, oil‑free surfaces will achieve the best contact and stack stability for comparative measurements. Is the gauge block appropriate for use with optical comparators and micrometres? The 1.003 mm nominal size and stable ceramic surface make this block a practical reference for comparator set‑ups and for verifying micrometre readings, providing a compact baseline for routine checks. What is the product identification for ordering and traceability? Product identification: Ceramic gauge block 1.003 mm (Metav IndustryLine), SKU M324.001.003, GTIN 4054469142302. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.004 mm Gauge Block Grade 1 DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine
Take advantage of the combination of certified standard compliance, Grade 1 accuracy and a hardened special steel construction for reliable reference measurements in production and inspection. Order directly via Metav Werkzeuge or consult Metav’s technical team for application advice and supply from Emmerich. End Gauge 1.004 mm — Grade 1 precision reference, DIN EN ISO 3650 End Gauge 1.004 mm is a precision reference gauge intended for high-accuracy dimensional checks and calibration tasks in inspection and quality control environments. DIN EN ISO 3650 standard Grade 1 accuracy Special steel, hardened Compact cross-section 30 x 9 mm Traceable accuracy for consistent inspection results The gauge is manufactured to DIN EN ISO 3650, delivered as a Grade 1 reference with a nominal size of 1.004 mm, providing a reproducible length standard for routine verification tasks. As a compact reference gauge, it supports repeatable comparisons against micrometres, callipers and comparator systems, helping to reduce measurement scatter in the production chain. The documented conformity to the relevant standard simplifies inclusion in internal quality procedures and audit trails. Durable construction for long-term stability Constructed from special steel that has been hardened, the gauge offers wear resistance and dimensional stability under normal inspection use. The material choice and heat treatment preserve the measuring faces and maintain the reference length across many cycles of handling and stacking. This durability translates into fewer replacements and a lower risk of drift, supporting uninterrupted quality control routines. Small format with practical handling characteristics With a compact cross-section of 30 x 9 mm (applicable for sizes up to 10 mm) and a mass of 0.003 kg, the reference block is easy to handle, position and stack in gauge sets. Its slim profile suits fine-adjustment work on small components and fixtures, while the modest weight reduces operator fatigue during repetitive checks. The geometry also allows secure seating in inspection fixtures and storage systems designed for precision blocks. Designed to integrate with inspection workflows The reference is supplied with clear identification (SKU M319.01004.1; GTIN 4054469130057) and falls into the end gauge category for laboratory and workshop use. Its conformity to DIN standards ensures compatibility with established metrological procedures, enabling straightforward integration into calibration schedules and quality documentation. For bespoke sets or larger portfolios of reference lengths, this gauge forms a reliable building block for an organised measurement system. Contact Metav Werkzeuge for tailored advice on integrating Metav IndustryLine reference gauges into inspection routines and for secure, prompt supply from Emmerich. Technical data Article number: M319.01004.1 GTIN: 4054469130057 Label: End gauge 1.004 mm, DIN EN ISO 3650, Grade 1 Nominal size: 1.004 mm Material: Special steel, hardened Grade: 1 Weight: 0.003 kg Facts Cross-section (≤10 mm): 30 x 9 mm TARIC / customs code: 90173000 eClass: 21170108 Special features Standard: DIN EN ISO 3650 Category: End gauges / reference blocks Intended use: Reference length for inspection and calibration FAQ What is the principal use of this end gauge? The end gauge provides a stable reference length for dimensional checks and calibration; the End Gauge 1.004 mm is suitable for verification of callipers, micrometres and comparator setups. Is the nominal length guaranteed by an international standard? Yes — the reference complies with DIN EN ISO 3650 and is classified as Grade 1 for tight, reproducible length reference. What material is the gauge made from and why does that matter? The gauge is made from hardened special steel, which preserves the measuring faces and ensures long-term dimensional stability during regular inspection use. Can this gauge be used in a gauge block set or stacked with other references? The compact geometry and precise faces permit stacking and use within organised reference sets; the cross-section 30 x 9 mm supports secure handling for sizes up to 10 mm. Which identification codes help with traceability in a quality system? Traceability is supported by SKU M319.01004.1 and GTIN 4054469130057, which can be recorded in calibration logs and inventory systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.004 mm Gauge Block Single Piece Grade 0, DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine
Combine Grade 0 accuracy, hardened special steel construction and conformity to DIN EN ISO 3650 for reliable, repeatable reference measurements; order directly via Metav Werkzeuge or consult our specialists for application support. Gauge Block 1.004 mm (Grade 0) — DIN EN ISO 3650, Hardened Special Steel The Gauge Block 1.004 mm (Grade 0) is a compact, high-precision reference standard intended for calibration tasks and dimensional control in inspection laboratories and production metrology. DIN EN ISO 3650 Grade 0 accuracy Hardened special steel construction Compact reference for precise dimensional control Precise reference for traceable measurements Made to DIN EN ISO 3650 and specified as Grade 0, this slip gauge offers a measured nominal size of 1.004 mm and serves as a reference element in the measurement chain. The Grade 0 specification ensures that the component meets stringent tolerances required for calibration and verification tasks, so the block can be used as a stable baseline for comparing micrometers, callipers and other length-measuring instruments. The combination of standard conformity and fine nominal size supports consistent dimensional control across inspection routines. Durable construction with consistent performance Manufactured from hardened special steel, the block provides the rigidity and wear resistance expected of gauge block standards. The material choice reduces dimensional drift under normal use and contributes to long service life when handled correctly. The cross-section dimensions follow the standard production variants (up to 10 mm: 30 × 9 mm), offering a compact form that is easy to integrate into existing gauge sets while still providing a reliable contact surface for comparators and measurement fixtures. Practical use in calibration and quality assurance As a single gauge block, the unit is suitable for stack building, establishing length standards and performing reference checks in both laboratory and shop-floor environments. It is intended for precision tasks where small increments matter and where a compact, traceable standard simplifies workflow. Using this block supports repeatable setups and reduces measurement uncertainty when incorporated into a calibrated set of master gauges or gauge block stacks used for instrument validation and routine quality assurance. For traceable Grade 0 standards, contact Metav Werkzeuge in Emmerich for expert advice and secure supply via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: M319.01004.0 GTIN: 4054469130040 Label: Single gauge block 1.004 mm, DIN EN ISO 3650, Grade 0 Core technical data Nominal size: 1.004 mm Weight: 0.003 kg Customs tariff number: 90173000 Cross-section: up to 10 mm — 30 × 9 mm; from 10.1 mm — 35 × 9 mm Special features Material: Special steel, hardened Standard: DIN EN ISO 3650 Grade: 0 Category: Gauge blocks (Measuring instruments) FAQ What is the primary application of this gauge block? The Gauge Block 1.004 mm (Grade 0) is intended as a reference standard for calibration, length comparison and dimensional checks in inspection laboratories and production metrology. Does the item meet an international standard for gauge blocks? Yes, the gauge block conforms to DIN EN ISO 3650 and is supplied as Grade 0, which denotes a high level of dimensional accuracy for reference use. What material is used and how should the block be handled? The block is made of hardened special steel; handle with clean gloves or finger cots to avoid oils and abrasives, store in a dry, protected environment to maintain surface condition and accuracy. Can this block be used in stacking and precision assemblies? Yes, the single gauge block can be combined in stacks to build longer reference lengths and is suitable for use with comparators, gauge tables and precision fixtures. Is a calibration certificate included with the product? The product data does not specify a supplied calibration certificate; calibration status is therefore not stated for the Gauge Block 1.004 mm (Grade 0). Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.004mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
Benefit from the combination of ceramic construction, Grade 1 accuracy and the exact 1.004 mm nominal size to secure a durable reference standard that supports reproducible length measurements; order directly via Metav Werkzeuge or ask our consultants for application advice. Ceramic Gauge Block 1.004 mm (Grade 1, DIN 861/1) — Metav IndustryLine The Ceramic Gauge Block 1.004 mm (Grade 1) is a compact reference standard for high‑precision length checks and calibration tasks in metrology laboratories and inspection benches. High‑stability ceramic material Grade 1 accuracy according to DIN 861/1 Nominal size 1.004 mm for fine calibration work Lightweight reference, suitable for controlled environments Reliable precision for reference measurements The block delivers consistent dimensional reference thanks to its Grade 1 classification under DIN 861/1, making it suitable for routine verification and comparison tasks in inspection and calibration workflows. The nominal size of 1.004 mm is produced to tight manufacturing standards, offering a stable benchmark for micrometrology applications. Emphasis is placed on traceable, repeatable measurements rather than speculative performance figures. Material benefits that reduce measurement uncertainty Constructed from ceramic, the gauge block offers low thermal expansion and excellent wear resistance compared with many metallic alternatives. These material properties contribute to thermal stability during short handling periods and reduce the risk of surface degradation in non‑corrosive environments. The ceramic body is also non‑magnetic, which is advantageous in precision settings where magnetic interaction could influence small probes or sensitive instruments. Integration into calibration and inspection routines As a compact reference standard, the block is straightforward to incorporate into calibration sequences and comparative checks. Its small mass and precise nominal dimension simplify handling on small gauges and comparator set‑ups, while the clear nominal value supports unambiguous documentation in quality records. For traceability, the article is supplied with clear identification (SKU M324.001.004), aiding inventory and audit processes in laboratories and production quality stations. Proven supply and quality assurance The product is offered under the Metav IndustryLine range and benefits from Metav’s established position as a precision partner for workshops and industry. Metav’s approach emphasises a reliable supply chain and a pragmatic quality filter based in Emmerich, supported by a broad product range and decades of expertise. This backing provides practical reassurance for procurement teams seeking dependable measurement standards without unnecessary complexity. Choose Metav IndustryLine's ceramic gauge block for reproducible measurements and contact Metav Werkzeuge in Emmerich for technical advice and secure supply. Technical data Article number: M324.001.004 GTIN: 4054469142319 Tariff number: 90173000 Facts Nominal size: 1.004 mm Weight: 0.001 kg Quality: Grade 1 (DIN 861/1) Special features Material: Ceramic Category: Endmasse (gauge block) eClass: 21170108 FAQ What level of accuracy does Grade 1 indicate? Grade 1 under DIN 861/1 denotes a high level of manufacturing precision for gauge blocks; the Ceramic Gauge Block 1.004 mm (Metav IndustryLine, SKU M324.001.004) is produced to that standard and intended for reliable reference measurements in inspection routines. Can the ceramic block be used in a standard calibration routine? Yes, the gauge block is suitable as a reference in calibration and comparative checks; its 1.004 mm nominal dimension and ceramic composition make it appropriate for controlled laboratory and inspection bench environments. How should the ceramic gauge block be handled and stored? Handle the block with clean, dry gloves or tweezers and store it in a protective case or drawer to avoid contamination and mechanical damage; the ceramic surface benefits from careful handling to preserve measurement integrity. Is the Ceramic Gauge Block 1.004 mm magnetic or corrosion‑prone? The block is non‑magnetic and ceramic, which offers good resistance to corrosion compared with many metal blocks; nonetheless, it should be kept away from harsh chemical exposure and handled in appropriate ambient conditions. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.005 mm Gauge Block Grade 0, DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine
Take advantage of precise conformity to international standards and the long-term stability of a hardened special-steel finish to secure a reliable length reference. Order the single gauge block 1.005 mm directly via Metav Werkzeuge or ask our consultants if needed. Single gauge block 1.005 mm (DIN EN ISO 3650) — Grade 0 by Metav IndustryLine A single gauge block 1.005 mm designed as a high-precision length standard for calibration, inspection and laboratory settings DIN EN ISO 3650, Grade 0 Nominal length 1.005 mm Hardened special steel construction Compact cross-section 30 x 9 mm Proven metrological accuracy for traceable measurement standards The 1.005 mm nominal length conforms to DIN EN ISO 3650, ensuring that the block meets established international tolerances for gauge blocks in Grade 0. This classification signals a very tight manufacturing tolerance and repeatable performance when used as a length reference in calibration benches or quality-control routines. The standardisation reduces uncertainty in measurement chains, which supports faster decision-making in production and inspection processes. Because the block is manufactured to these norms, it integrates seamlessly with established calibration procedures and stacking systems. Durable construction that supports long-term stability Manufactured from hardened special steel, the block resists wear and maintains dimensional stability under routine handling. The material choice promotes longevity and consistent contact surfaces for wringing and stacking, while the compact 30 x 9 mm cross-section (applicable for sizes up to 10 mm) provides a good balance between stiffness and ease of handling. Hardened steel also helps to maintain surface integrity over many cycles, reducing the need for frequent replacement and supporting reliable results across repeated measurements. Practical benefits for workshops and calibration labs As a compact length standard, this gauge block simplifies setup and alignment tasks where sub-millimetre accuracy is required. The small footprint and standardised face geometry enable efficient stacking with other blocks to create composite lengths, while the low mass (approximately 0.003 kg) makes manual handling straightforward during calibration work. The clear standard compliance and material properties reduce downtime spent confirming compatibility, enabling faster throughput in inspection workflows and easing integration into existing sets of reference standards. Quality assurance and supply confidence Supplied under the Metav IndustryLine label, the block reflects a distribution philosophy that emphasises accessibility to precision tools and dependable logistics from Emmerich. The adherence to recognised norms and the robust material specification provide a defensible basis for traceable measurements and quality records. For operations seeking compact, standard-compliant reference tools, the combination of DIN EN ISO 3650 conformity and hardened special steel construction delivers both technical reliability and practical durability. For secure, standard-compliant reference standards please contact Metav Werkzeuge to obtain the Grade 0 single gauge block 1.005 mm and discuss compatibility with existing sets or calibration needs. Technical Data Article number: M319.01005.0 GTIN: 4054469130064 Tariff number: 90173000 EClass: 21170108 Facts Nominal length: 1.005 mm Weight: 0.003 kg Cross-section: 30 x 9 mm Grade: 0 Special features Standard: DIN EN ISO 3650 Material: hardened special steel Category: Gauge blocks (End measures) Intended use: calibration and inspection length standards FAQ What tolerance class does this gauge block meet? The single gauge block 1.005 mm is manufactured to Grade 0 in accordance with DIN EN ISO 3650, providing tight dimensional tolerances for calibration tasks. Which material is used and why is it beneficial? The block is made from hardened special steel, chosen for wear resistance and dimensional stability, which supports reliable wringing and long-term performance. Can this block be stacked with other gauge blocks? Yes, the block’s standardised faces and compact cross-section allow stacking with compatible gauge blocks to form composite reference lengths. Is this gauge block suitable for laboratory calibration use? Compliance with DIN EN ISO 3650 and the Grade 0 specification make the block appropriate as a laboratory reference within a calibrated measurement chain. What is the article number for ordering and traceability? Ordering and traceability use article number M319.01005.0; the GTIN is 4054469130064 for catalogue identification. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.005 mm Gauge Block Grade 1, Hardened Special Steel, DIN EN ISO 3650 - Metav IndustryLine
The precise DIN EN ISO 3650 conformity, hardened special steel construction and compact cross-section combine to deliver a stable, low‑wear reference for dimensional control. Use this Grade 1 end gauge for repeatable checks and reference stacking; Order the end gauge directly via Metav Werkzeuge or ask our consultants if needed. End gauge 1.005 mm — Grade 1 gauge block, DIN EN ISO 3650 (Metav IndustryLine) The End gauge 1.005 mm is a precision gauge block intended as a reference standard for calibration labs, toolrooms and quality control tasks where sub‑millimetre accuracy is required DIN EN ISO 3650 compliant Grade 1 tolerance Hardened special steel construction Nominal size 1.005 mm precision Compact cross-section 30x9 mm for small sizes A reliable reference for dimensional control This Grade 1 gauge block provides a consistent reference for routine inspections and comparative measurements. Manufactured to DIN EN ISO 3650, the block’s 1.005 mm nominal size is produced with tight manufacturing control so that it functions as a stable benchmark in stack sets and master comparisons. The adherence to a recognised standard ensures compatibility with existing metrology procedures and simplifies traceability in quality documentation. Built for durability and handling in the workshop The body is machined from hardened special steel, offering high wear resistance and long service life even with frequent use. The compact cross‑section for small sizes (approx. 30x9 mm) delivers good rigidity with minimal mass—helpful when assembling gauge stacks or handling many masters during a shift. The small weight and slim profile make positioning and polishing straightforward while the hardened surface reduces the risk of rapid dimensional change under normal workshop conditions. How it integrates into quality workflows As a master reference, the block supports quick comparative checks and stack building to reach required nominal lengths without complex setups. The Grade 1 tolerance provides a balance between high precision and everyday usability, making it suitable for calibration benches, incoming inspection and production spot checks. When combined with calibrated comparator equipment, the block helps maintain measurement consistency across shifts and operators, contributing to reproducible production results. For purchase enquiries or detailed technical clarification about Metav IndustryLine gauge blocks, contact Metav Werkzeuge in Emmerich; consultants are available by phone or email to advise on selection and integration into existing measurement routines. Technical data Article number: M319.01005.1 GTIN: 4054469130071 Label: Endmaß 1,005 mm, DIN ISO 3650, Güte 1 DIN ISO 3650 Facts Nominal size: 1.005 mm Weight: 0.003 kg Cross-section: up to 10 mm — 30x9 mm; above 10.1 mm — 35x9 mm Standard: DIN EN ISO 3650 Grade: 1 Special features Material: hardened special steel Category: End gauges (gauge blocks) Tariff number: 90173000 SKU: M319.01005.1 FAQ What level of accuracy does this gauge block provide? The Grade 1 end gauge conforms to DIN EN ISO 3650, offering the accuracy expected for Grade 1 masters; the 1.005 mm nominal size is manufactured to that standard for reliable reference use. Is the material suitable for everyday workshop use? Yes — the block is made from hardened special steel, giving good wear resistance and long service life under normal inspection and stacking routines. Can this block be used in gauge stacks? The block’s compact cross‑section and precise nominal size make it suitable for building gauge stacks to obtain combined lengths for calibration and comparative measurements. Does the product include a certificate? The product specification does not state an included calibration certificate; any certification or specific calibration service should be confirmed with Metav Werkzeuge prior to purchase. What applications are typical for this end gauge? Typical uses include calibration benches, incoming inspection, toolroom checks and production spot checks where a stable Grade 1 reference is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.005mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
The combination of ceramic construction, Grade 1 accuracy and a nominal length of 1.005 mm ensures a stable reference standard for fine calibration tasks; order the gauge block directly via Metav Werkzeuge or consult our specialists for application advice. Ceramic gauge block 1.005 mm, Grade 1 DIN 861/1 — Ceramic end measure with high dimensional stability (Metav IndustryLine) A Ceramic gauge block 1.005 mm, Grade 1 designed as a compact reference standard for precision length measurements and calibration work in metrology and inspection. Grade 1 accuracy according to DIN 861/1 Made from thermally stable ceramic Nominal length 1.005 mm for fine gauges Compact and lightweight for easy handling Reliable reference for fine calibration A compact reference unit manufactured from ceramic offers excellent dimensional stability and resistance to wear compared with many metallic gauges. The Grade 1 specification (DIN 861/1) denotes a tight tolerance band, making this block suitable as a reference in calibration benches and quality control routines where small incremental differences matter. The nominal length 1.005 mm is ideal for setting or checking micrometre standards and fine-gap fixtures; the combination of material and tolerance reduces routine rework by providing a stable baseline for measurements. Material advantages that lower measurement uncertainty Ceramic as the base material contributes to reduced variation from temperature shifts and surface wear, delivering consistent contact behaviour over repeated use. The low coefficient of expansion inherent to high-quality ceramic supports repeatable length standards under normal workshop conditions, while the hard surface resists deformation. These properties translate into fewer adjustments during inspection runs and a lower risk of introducing systematic error, supporting faster, more reliable decisions on part conformity. Practical use and storage in the workshop or lab The compact design and lightweight construction make handling and temporary placement straightforward during setup and verification tasks. Integration into a calibration workflow is simple: the block functions as a master for comparative checks, gauge setting and fine alignment tasks. Identification and ordering are straightforward with the SKU M324.001.005; traceability is supported by the GTIN and product labelling, facilitating stock control and record-keeping in quality systems. Careful storage on a non-abrasive surface will preserve the polished measuring faces and prolong service life. Choose the Metav IndustryLine ceramic gauge block for dependable, thermally stable reference measurements — order via Metav Werkzeuge in Emmerich or contact our consultants at info@metav-werkzeuge.com or +49 2822 7131930 for technical guidance. Technical data Article number: M324.001.005 GTIN: 4054469142326 Eclass: 21170108 Tariff number: 90173000 Numbers / Core technical data Nominal length: 1.005 mm Weight: 0.001 kg Grade: 1 (DIN 861/1) Special features / Versions Material: ceramic Category: gauge blocks / end measures Label: Ceramic gauge block 1.005mm, Grade 1 FAQ What tolerance class does this gauge block meet? The Ceramic gauge block 1.005 mm meets Grade 1 tolerance as specified in DIN 861/1, providing a precise reference for fine calibration tasks. Is the material suitable for repeat contact measurements? Yes. The ceramic construction of this gauge block offers high dimensional stability and wear resistance, making it suitable for repeated comparative and setting measurements. How should the gauge block be stored to maintain accuracy? Store the block on a clean, non-abrasive surface and protect it from contaminants and mechanical shocks; regular visual inspection preserves the measuring faces and prolongs service life. Which identifier helps with procurement and traceability? Order and stock using SKU M324.001.005 and GTIN 4054469142326 for consistent traceability and inventory management. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.006 mm Gauge Block Grade 0, DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine
Benefit from Grade 0 conformity and a compact, hardened construction that delivers repeatable reference lengths with minimal handling error; combine DIN EN ISO 3650 compliance and a stable nominal length for trustworthy set-ups. Order the single gauge block 1.006 mm directly via Metav Werkzeuge or ask our consultants if needed. Single gauge block 1.006 mm — Grade 0 reference length, DIN EN ISO 3650, Metav IndustryLine The Single gauge block 1.006 mm provides a precision reference for calibration, comparative measuring and setting lengths in metrology laboratories and workshop quality control. Grade 0 accuracy to DIN EN ISO 3650 Hardened special steel construction Nominal length 1.006 mm traceable standard Compact cross-section 30 x 9 mm for up to 10 mm sizes Reliable reference for accurate measurements A straight measurement standard with Grade 0 accuracy according to DIN EN ISO 3650 establishes a clear, reproducible baseline for length measurement. The nominal length of 1.006 mm is produced to tight tolerances so that it serves as a dependable reference in stacks or as a single master gauge. This consistency reduces uncertainty in comparative checks and helps to maintain process capability in machining and inspection tasks. Durable build for routine workshop use Constructed from hardened special steel, the block resists wear and retains flatness under normal handling, which extends service life and lowers replacement frequency. The compact cross-section (30 x 9 mm for sizes up to 10 mm) supports stable clamping in gauge holders and easy manual handling while keeping thermal mass low for faster thermal equilibrium. These attributes make the standard suitable for frequent shop-floor use without sacrificing the stability required for reference measurements. Practical benefits for metrology and production As a precise length standard, this gauge block simplifies set-up of comparators, fixture checking and gage calibration routines. The small footprint and low weight make it straightforward to integrate into existing stacks and measuring routines, while compliance with international standardisation fosters compatibility with established calibration procedures. For operations that require documented traceability, the block’s conformity to recognised norms aids in record-keeping and audit readiness. For exact specification matching and delivery from Metav Werkzeuge, request the single gauge block from Metav IndustryLine or consult our technical advisers to verify suitability for the specific measurement chain Technical data Article number: M319.01006.0 GTIN: 4054469130088 Category: Gauge blocks Label: Einzel-Endmaß 1,006 mm, DIN ISO 3650, Güte 0 DIN ISO 3650 Facts Nominal length: 1.006 mm Weight: 0.003 kg Cross-section: up to 10 mm → 30 x 9 mm; from 10.1 mm → 35 x 9 mm Tariff code: 90173000 Grade: 0 Special features Material: special steel, hardened Standard: DIN EN ISO 3650 Brand: Metav IndustryLine FAQ What accuracy class does this gauge block have? The block is specified as Grade 0 according to DIN EN ISO 3650, which denotes a high-precision reference suited to laboratory and workshop calibration tasks. Is the gauge block supplied calibrated with an ISO 17025 certificate? The single gauge block 1.006 mm is delivered as a standard Grade 0 reference; an ISO 17025 calibration certificate is not automatically included unless explicitly ordered as a calibrated item. What applications are typical for this type of block? This type of gauge block is used for calibration masters, comparator set-ups, stack building for length setting and routine verification tasks in production and inspection environments. How should the block be stored to maintain accuracy? The block should be kept clean, dry and stored in a protective case or rack to avoid surface contamination and mechanical damage; stable storage temperature helps preserve dimensional stability. Which material is used and how does that affect use? Made from hardened special steel, the block offers wear resistance and good surface stability under normal handling, making it suitable for regular measurement cycles. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
ensure traceable length calibration with gauge blocks
gauge blocks, also called slip gauges or end gauges, are precision length standards designed to transfer exact measures during calibration and setup. Manufactured and graded for metrological use, they provide the reference dimensions needed to verify and adjust measuring instruments in industrial workshops and calibration labs.
how gauge blocks work and where they are essential
gauge blocks are used to create known lengths by wringing individual blocks together or by using a single block as a reference. length calibration in industry commonly relies on parallel gauge blocks, while angle, cylinder and sphere end gauges serve specialised tasks. these blocks are produced in steel, ceramic or carbide, and their material choice balances wear resistance with thermal behaviour. regular calibration—typically performed annually—by DAkkS-accredited laboratories ensures traceability. the highest-precision reference work, class K, is certified by the PTB using laser techniques; classes 0, 1 and 2 are tested under progressively less controlled conditions (class 0 in a climate-controlled lab, class 1 in a standard measurement room, class 2 in production).
measurable benefits that cut downtime and uncertainty
- consistent, traceable length standards reduce rework and measurement disputes by enabling reliable instrument calibration.
- choosing the correct material (steel, ceramic, carbide) extends service life and limits wear in high-use environments.
- selecting the right accuracy class (K, 0, 1 or 2) matches calibration effort to application needs and avoids over‑specification.
- annual calibration by accredited labs maintains documented compliance and supports quality systems such as ISO.
why Metav is a smart partner for precision standards
Metav combines specialist knowledge with a broad range of measurement technology, making the procurement of gauge blocks straightforward and dependable. with over 48,000 customers and more than 250,000 products stocked from Emmerich, Metav acts as a pragmatic quality filter for European workshops, reducing supplier complexity and ensuring consistent supply.
In short, gauge blocks deliver traceable, material‑appropriate and class‑matched references that keep calibration workflows efficient and auditable.
faq
what materials are gauge blocks available in and why does it matter?
gauge blocks are typically supplied in steel, ceramic or carbide. material choice affects wear resistance, stability and thermal expansion; selecting the right material for your environment optimises longevity and measurement stability.
how often should gauge blocks be calibrated?
industry practice is an annual calibration cycle, carried out by DAkkS-accredited laboratories, though frequency can be increased depending on usage and required uncertainty.
what do the accuracy classes k, 0, 1 and 2 indicate?
the classes denote graded tolerances and test conditions: K is the highest precision (certified by PTB with laser measurement), class 0 is checked under climate-controlled lab conditions, class 1 in a normal measurement room and class 2 in production environments.
are parallel gauge blocks always used for length calibration?
yes; for length calibration the parallel gauge blocks are the primary standard because they provide exact planar faces for wringing and stacking to create precise lengths.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com