M27x1 Limit Thread Go/No-Go Gauge Metric ISO Fine Pitch Right-Hand, Hardened Gauge Steel, DIN 13 6H - Metav IndustryLine

Take advantage of a hardened gauge steel construction and strict DIN 13, 6H conformity for reliable thread verification in production. The combination of compact handling, repeatable go/no-go control and compatibility with metric ISO fine threads keeps throughput steady and rejects minimal. Order the Limit thread plug gauge M27 x 1 mm directly via Metav Werkzeuge or ask our consultants if needed.

Limit thread plug gauge M27 x 1 mm — metric ISO fine thread, right-hand (Metav IndustryLine)

The Limit thread plug gauge M27 x 1 mm is designed for fast, repeatable inspection of metric ISO fine threads in workshop and production environments, serving as a go/no-go reference for right-hand threads.

• Hardened gauge steel construction
• Conforms to DIN 13, tolerance 6H
• For M27 x 1 mm metric ISO fine threads
• Right-hand limit plug gauge, go/no-go fit

Reliable verification according to international thread standards

The gauge is manufactured to match DIN 13 with a 6H tolerance class, providing an objective pass/fail criterion for internal threads. As a limit plug gauge, it embodies the established go/no-go principle: the "go" end verifies acceptance within tolerance while the "no-go" end confirms that oversize conditions are detected. This clear mechanical check reduces interpretation errors and supports consistent quality decisions on the shop floor.

Durable materials for repeatable inspections

Made from hardened gauge steel, the tool resists wear during routine checks and retains dimensional integrity over many cycles. The robust construction, paired with a compact mass (approx. 0.31 kg), delivers a balance of stiffness and ergonomic handling for handheld verification. Frequent use in production is therefore less likely to introduce measurement drift, which preserves part conformity and reduces rework.

Streamlined process control and productivity gains

Integrating a simple limit gauge into inspection routines shortens cycle times compared with measurement-heavy methods. The clear go/no-go result enables rapid sorting and immediate decisions at the point of production, helping to avoid downstream rejects. This pragmatic approach to quality control supports higher throughput while maintaining reliable acceptance criteria for metric ISO fine threads.

Typical applications and handling recommendations

The plug gauge is intended for inspection of internal metric ISO fine threads in components, assemblies and fixtures where an M27 x 1 mm thread is specified. The right-hand design matches standard fastener orientation. For consistent performance, keep the gauge clean, protect it from shocks, and store it in a dry environment. Periodic inspection against a master or accredited calibration service is recommended to maintain confidence in the inspection result.

For tailored advice on integrating the Metav IndustryLine limit plug gauge into production, contact Metav Werkzeuge to request the M315.027.4 SKU or to arrange technical clarification at info@metav-werkzeuge.com or +49 2822 7131930

Technical data

• Article number: M315.027.4
• GTIN: 4054469122816
• SKU: M315.027.4

Facts

• Thread size: M27 x 1 mm
• Weight: 0.31 kg
• Tariff code: 90173000
• eClass: 21170235

Special features

• Material: hardened gauge steel
• Standard: DIN 13, tolerance 6H
• Right-hand metric ISO fine thread plug gauge
• Function: limit / go-no-go inspection
• Category: Gauges / Plug gauges

FAQ

What thread form and size does this gauge inspect?
The Limit thread plug gauge M27 x 1 mm inspects internal metric ISO fine threads of size M27 x 1 mm and is intended for right-hand threads.

What standard and tolerance class does the gauge comply with?
The plug gauge conforms to DIN 13 with a 6H tolerance, providing a standardised acceptance criterion for internal threads.

What material is the gauge made from and why does it matter?
This limit plug gauge is made from hardened gauge steel, which ensures wear resistance and dimensional stability for repeatable inspection results.

How is the gauge used during production checks?
Use the gauge as a go/no-go reference: the "go" end must enter freely; the "no-go" end must not. The Limit thread plug gauge M27 x 1 mm simplifies pass/fail decisions at the machine or assembly station.

Is the gauge suitable for routine quality control on the shop floor?
Yes, the Metav IndustryLine limit plug gauge (SKU M315.027.4) is designed for shop-floor verification of metric ISO fine threads, offering fast, objective checks to support process control.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com