150mm Closure Clamp 6848H Horizontal With Counterholder, 1600N Holding Force - AMF
Take advantage of a compact, horizontal locking solution that combines a high holding force and an adjustable clamping range for secure, repeatable fixturing; order directly through Metav Werkzeuge or request tailored advice from our consultants. AMF Closure clamp No. 6848H (horizontal) — Size 2, 1,600 N holding force The Closure clamp No. 6848H is a horizontal locking latch designed for fixtures and jigs, supplied complete with a counter holder for reliable clamping in production and assembly applications. Horizontal locking clamp, size 2 Max holding force 1,600 N Adjustable clamping range 42–76 mm Supplied with counter holder Secure, repeatable holding for production use A robust horizontal locking solution delivers consistent clamping across repetitive operations. With a holding force of 1,600 N and an adjustable clamping range of 42–76 mm, this clamp secures parts reliably without frequent readjustment. The mechanical design translates applied force into stable contact pressure, reducing the risk of part movement during machining, assembly or testing. For jigs and fixture systems where repeatability matters, the clamp’s predictable performance contributes directly to process stability and fewer rejects. Fast setup and flexible adjustment reduce cycle times The horizontal configuration and supplied counter holder simplify installation and alignment on fixture plates. The latch features an adjustable reach (L1 125–159 mm) and a stroke adjustment range (M 19.5–23.5 mm), enabling quick adaptation to different workpiece heights and tolerances. These characteristics support faster changeovers and fewer stoppages: the mechanical adjustments are intuitive and minimise downtime, helping to increase throughput on small-batch and large-scale production alike. Made for industrial workshop conditions Designed for demanding shop-floor environments, the clamp’s compact geometry and horizontal design allow close packing on fixture plates and robust engagement under load. The closure latch is suitable for use in assembly, welding fixtures and packaging jigs where secure locking is essential. The concept focuses on longevity and operational reliability: a simple, service-friendly mechanism reduces maintenance intervals while maintaining consistent clamping performance throughout repetitive cycles. Clear installation guidance and maintenance-friendly design Mounting and adjustment options are straightforward, with defined datum dimensions and a clear clamping envelope that aids in fixture planning. The latch can be integrated into modular tooling systems using the specified dimensional data for confident placement. Routine inspection is limited to fastener torque checks and visual wear assessment, keeping lifecycle maintenance simple. For additional technical data or application-specific recommendations, Metav Werkzeuge provides specialist advice to match the clamp to the required fixturing task. Contact Metav Werkzeuge for tailored application advice on the AMF horizontal closure clamp No. 6848H — ensure the right configuration for dependable fixturing; call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: 4123682200NW Model: 6848H Label: Closure clamp No. 6848H, Size 2, horizontal, AMF Execution: horizontal; including counter holder Packaging unit: 1 Facts Size: 2 Holding force max: 1,600 N B min: 42 mm B max: 76 mm C: 13 mm D: 5.2 mm D1: 4 mm E min: 38 mm E max: 72 mm F: 11 mm H: 12 mm H1: 47 mm H2: 99 mm K: 6.4 mm L1: 125–159 mm L5: 69 mm M: 19.5–23.5 mm N: 38 mm P: 26 mm Special features Horizontal locking design Supplied with counter holder AMF brand Adjustable clamping range 42–76 mm L1 adjustable 125–159 mm FAQ What is the maximum holding force of this clamp? The AMF Closure clamp No. 6848H provides a maximum holding force of 1,600 N, suitable for many light to medium duty fixturing tasks. Which clamping range does the latch cover? The locking latch covers an adjustable clamping range of 42–76 mm, with L1 reach adjustable from 125 to 159 mm to suit various part heights. Is the counter holder included with the clamp? Yes, the delivery includes a counter holder; the Closure clamp No. 6848H arrives ready for mounting with the paired counter element to ensure secure engagement. Can this clamp be used in welding fixtures and assembly jigs? The horizontal design and stable locking action of the AMF No. 6848H make it well suited for welding fixtures and assembly jigs where repeatable, secure clamping is required. What information is helpful for mounting on a fixture plate? Refer to the dimensional facts (B, C, H, L1, M etc.) for fixture planning; the SKU 4123682200NW identifies the exact configuration of this AMF horizontal closure clamp. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
150mm Closure Clamp 6848H Horizontal With Counterholder, 7000 N Holding Force - AMF
Benefit from a compact, robust solution that combines a 7,000 N holding force with a horizontal mounting and an integrated counterholder for secure, repeatable clamping. Order the clamp directly via Metav Werkzeuge or consult their advisors for application-specific guidance. AMF 6848H horizontal toggle clamp, size 4 — 7,000 N holding force The AMF 6848H horizontal toggle clamp, size 4 is a sturdy workholding device designed for jigs, fixtures and repetitive assembly tasks that demand reliable clamping and fast part changeover. Horizontal configuration with counterholder included 7,000 N maximum holding force Adjustable clamping range 66–130 mm Robust industrial design, size 4 Secure, repeatable clamping for production use The horizontal toggle clamp delivers a high clamping capacity with a maximum holding force of 7,000 N, making it suitable for demanding fixture applications where consistent pressure and retention are essential. The integrated counterholder removes the need for separate support components, simplifying fixture layout and reducing part count. In practice, this translates to fewer setup errors and a stable clamp that maintains position under cyclic loads, improving process stability on the assembly line. Easy integration thanks to defined adjustment ranges Designed for straightforward installation, the unit offers an adjustable clamping range (66–130 mm) that covers common workpiece thicknesses. Key installation dimensions such as L1: 209–273 mm and M: 35.0–46.0 mm enable precise alignment within fixtures and jigs; these measurable values support rapid CAD integration and accurate positioning during fixture design. The horizontal orientation permits low-profile mounting on plates or frames, while the clearly stated dimensions facilitate reliable repeatability between setups. Built for industrial workflows and efficient operations As a dedicated workholding component, the clamp supports faster cycle times and predictable clamping behaviour, which helps to reduce rework and downtime on production lines. The size 4 designation denotes an industrial-grade variant intended for medium-duty to heavy-duty applications where repeatability and mechanical robustness matter. With a single packaging unit and a compact footprint, the device is easy to stock and replace, supporting continuity in small-batch and series production alike. For tailored advice and rapid supply of AMF horizontal toggle clamps with a 7,000 N holding force, contact Metav Werkzeuge GmbH at +49 2822 7131930 or info@metav-werkzeuge.com Technical data Article number: 4123682400NW Type: 6848H Product name: AMF horizontal toggle clamp, size 4 Configuration: horizontal, includes counterholder Packaging unit: 1 Facts Holding force: 7,000 N Size: 4 B min: 66 mm B max: 130 mm C: 32 mm D: 8.5 mm D1: 8 mm E min: 59 mm E max: 123 mm F: 19 mm H: 26 mm H1: 94.5 mm H2: 171.5 mm K: 9.5 mm L1: 209–273 mm L5: 111 mm M: 35.0–46.0 mm N: 64.3 mm P: 53.5 mm Special features Horizontal mounting Counterholder included Size 4 designation Suitable for industrial fixtures Robust holding capacity FAQ What is the maximum holding force of this clamp? The AMF 6848H horizontal toggle clamp provides a maximum holding force of 7,000 N (SKU 4123682400NW), suitable for medium-duty to heavy-duty fixturing. What clamping range does the device cover? The unit features an adjustable clamping span from 66 to 130 mm, allowing accommodation of a wide range of workpiece thicknesses. Is a counterholder included and is the clamp for horizontal mounting? Yes, the clamp is supplied in a horizontal configuration and includes a counterholder to simplify fixture assembly and ensure secure engagement. Which dimensions should be checked for integration into a jig? Relevant dimensions include L1: 209–273 mm, H1: 94.5 mm, H2: 171.5 mm and the clamping range B: 66–130 mm; these values are specified for precise positioning during fixture design. What applications suit this type of clamp? The clamp is well suited to jigs, fixtures and production tooling where repeatable, secure clamping is required, for example in assembly, welding or machining fixtures using standard clamping stations. Manufacturer: AMF / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
150mm Closure Clamp 6848V Vertical With Counterholder, 3 Size Range 34.5–64mm, 3200N - AMF
Take advantage of a high holding force of 3200 N, compact vertical design and an adjustable clamping range for secure, repeatable fixtures in production. Order directly via Metav Werkzeuge or consult our specialists for integration advice. Toggle clamp No. 6848V, Size 3 (vertical) – AMF | vertical toggle clamp, 3200 N hold The Toggle clamp No. 6848V (vertical) is a compact industrial closure clamp for fixtures and jigs, supplied with a counter-holder and designed for vertical clamping tasks in assembly and machining setups. Vertical orientation with counter-holder included Holding force up to 3200 N Adjustable clamping range B 34.5–64 mm Compact mounting length L1 125 mm Robust vertical clamping for secure production fixtures The vertical toggle clamp offers a holding force of 3200 N, making it suitable where reliable, vibration-resistant retention is required. The vertical action keeps the clamping motion aligned with the workpiece, reducing lateral forces and preventing unwanted movement during operations. This results in stable fixation for repetitive tasks and short cycle times. The mechanism is designed for quick engagement and release, providing a balance between secure retention and efficient workflow. Precise adjustability for varied workpiece dimensions With an adjustable clamping range from B min 34.5 mm to B max 64 mm, the device accommodates a wide span of component sizes without complex readjustment. The adjustable spindle range M 24.5–32.0 mm allows fine tuning of clamp height, while the compact L1 125 mm and overall dimensions keep the unit low-profile on fixtures. These measurable parameters translate directly into reduced set-up time and fewer fixture variants, supporting lean production and easier jig design. Simple integration and long-term operational reliability The vertical clamp is supplied including a counter-holder, enabling immediate installation into existing tooling plates or custom jigs. Standardised mounting dimensions and the clearly defined pin and hole diameters (for example D 6.5 mm, D1 6 mm) ease retrofit and repeatability. The design is focused on durability and predictable behaviour under load, reducing downtime. For workshops seeking dependable components, this clamp provides a straightforward way to improve process repeatability and operator confidence. For professional integration and procurement advice — contact Metav Werkzeuge today to discuss how the AMF vertical toggle clamp No. 6848V can be fitted into existing fixtures or bespoke tooling solutions. Technical data SKU: 4123683300NW Type: 6848V Manufacturer: AMF Product: Toggle clamp (vertical) Packaging unit: 1 Facts Holding force max: 3200 N B min: 34.5 mm B max: 64 mm C: 19 mm D: 6.5 mm D1: 6 mm E min: 7 mm E max: 36 mm F: 14 mm G: 25 mm H: 6 mm H1: 70 mm H2: 136 mm K: 8 mm L1: 125 mm M: 24.5–32.0 mm N: 48 mm P: 35 mm Special features Vertical orientation Includes counter-holder Size 3 Compact mounting length Quick-action toggle mechanism FAQ What is the maximum holding force of this clamp? The clamp delivers a maximum holding force of 3200 N, as stated for the AMF vertical toggle clamp No. 6848V (SKU 4123683300NW). Which clamping range does the device cover? The adjustable clamping capacity covers B 34.5–64 mm, with spindle adjustment M 24.5–32.0 mm for fine height tuning on the AMF toggle clamp. Is a counter-holder supplied with the clamp? Yes, the unit is supplied including a counter-holder, enabling immediate mounting and use in most fixture layouts. Which mounting dimensions are relevant for fixture design? Key mounting values include L1 125 mm, hole diameters D 6.5 mm / D1 6 mm and base heights H1 70 mm / H2 136 mm, useful when integrating the clamp into tooling plates. Can the clamp be used for repetitive industrial production? The AMF vertical toggle clamp No. 6848V is designed for repeated engagement and reliable retention, making it suitable for jigs and fixtures in serial production environments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
150mm Closure Clamp 6848V Vertical With Counterholder, Max Hold 1600 N - AMF
Take advantage of the vertical action and 1,600 N holding force combined with a compact, adjustable clamping range for secure, repeatable fixturing; order directly via Metav Werkzeuge or consult our advisers for technical fitment. AMF 6848V Vertical Toggle Latch (Size 2) – 1,600 N holding force, counterholder included An AMF 6848V vertical toggle latch engineered for secure vertical clamping in fixtures and jigs, supplied complete with a counterholder for precise engagement. Vertical action with counterholder included 1,600 N maximum holding force Adjustable clamping range 24–49 mm Compact footprint for fixtures and jigs Reliable clamping performance for production fixtures The vertical toggle latch provides a consistent holding force of 1,600 N, ensuring parts remain stable during assembly and machining operations. Vertical action clamps are designed to apply force through a controlled vertical motion, which reduces lateral movement and improves repeatability on fixtures. The included counterholder secures the mating surface and simplifies alignment, so clamping cycles stay uniform even under repetitive loads. This makes the latch suitable for medium-duty applications where reliable retention and repeatable positioning are required. Clear adjustability for varied workpieces Adjustment features allow a broad clamping range of 24–49 mm (B min–B max), enabling the latch to accommodate different stock thicknesses without additional parts. Spindle adjustment is provided in the range 19.5–23.5 mm, permitting fine tuning of clamping height during setup. These measurable settings reduce setup time and eliminate guesswork: once the correct position is set, the mechanism locks at the chosen engagement without further modification. The compact dimensions support integration into space-constrained jigs while maintaining straightforward mechanical adjustment. Easy integration and dependable operation Designed for straightforward mounting in production jigs, the latch combines compact external dimensions with clearly defined mounting geometry to simplify assembly layouts. Key dimensions (for example L1 = 91 mm and H2 = 99 mm) provide a stable footprint for bolting or welding into frames. The mechanism performs a positive mechanical lock when engaged, so corrective actions are minimised during cycle changes. Documentation of the principal dimensions and the 1,600 N rating supports planning for multiple fixtures and aids in choosing compatible fastening hardware for a robust installation. Contact Metav Werkzeuge today for specialist advice and assured supply of the AMF 6848V vertical toggle latch — call +49 2822 7131930 or email info@metav-werkzeuge.com to confirm suitability and availability Technical data Article number: 4123683200NW Type: 6848V Product: Vertical toggle latch (locking clamp) Manufacturer: AMF Packaging unit: 1 Core data Size: 2 Maximum holding force: 1,600 N Clamping range B min–B max: 24–49 mm C: 13 mm D: 5.2 mm D1: 4 mm E min–E max: 5–30 mm F: 11 mm G: 19 mm H: 4.5 mm H1: 47 mm H2: 99 mm K: 6.4 mm L1: 91 mm M: 19.5–23.5 mm N: 38 mm P: 26 mm Special features Vertical action Counterholder included Adjustable clamping range 24–49 mm Compact footprint, suitable for fixtures and jigs Positive mechanical locking at 1,600 N holding force FAQ What is the maximum holding force of the latch? The AMF 6848V vertical toggle latch offers a maximum holding force of 1,600 N. Which clamping range does the device cover? The clamping range is 24–49 mm (B min–B max), allowing adaptation to different workpiece thicknesses. Is a counterholder supplied with the product? Yes, the item is delivered vertical with counterholder included, enabling precise engagement without separate components. For which applications is this clamp suitable? The latch is intended for fixtures, jigs and medium-duty production applications where secure vertical clamping and repeatability are required. How is the clamping height adjusted? Adjustment is achieved via the spindle settings, with the M dimension offering 19.5–23.5 mm for fine tuning during setup. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
150mm Closure Clamp Heavy Duty Incl. Counterholder, 15kN Holding Force - AMF
Take advantage of the combination of heavy‑duty horizontal clamping, a 15,000 N holding force and an adjustable stroke to secure workpieces reliably and speed up cycle times; order the clamp via Metav Werkzeuge or ask their advisers for layout support and delivery options. AMF toggle clamp 6849PH — heavy‑duty horizontal, Size 4 The AMF toggle clamp 6849PH is a heavy‑duty horizontal closure clamp designed for demanding jigs and fixtures in production environments. Heavy‑duty horizontal design 15,000 N maximum holding force Adjustable stroke 66 mm Includes counter‑holder Size 4 for robust fixtures Secure heavy‑duty workholding that increases uptime The heavy‑duty horizontal design delivers a consistent clamping force tailored to industrial production. With a maximum holding force of 15,000 N, the clamp reduces slippage and maintains workpiece position under cutting, welding or assembly loads, enhancing process stability and lowering rework rates. The mechanical toggle action provides instant locking, so fixture cycle times are shorter and operator handling is simplified. Emphasis on repeatability and secure contact points translates into fewer setup adjustments and steadier throughput on the shop floor. Quick adjustment and reliable repeatability for diverse parts Built for fast integration, the closure offers an adjustable stroke of 66 mm, enabling alignment with varying workpiece heights and fixture geometries. The included counter‑holder secures the mating surface and improves reproducibility across repeated clamping cycles, which is especially valuable for batch production. Adjustment ranges such as 42–107 mm for the main clamping span mean fewer spare parts and less downtime when switching jobs. The result is a more efficient workflow and a tangible reduction in setup time per operation. Adaptability across fixture designs and applications Sizing and geometry values make the clamp versatile for a broad range of fixtures: the main span adjusts to 42–107 mm, the effective contact travel covers 24–90 mm, and the mounting footprint supports compact or extended layouts. The AMF toggle clamp 6849PH accommodates variations in workpiece form and fixturing strategy while maintaining a secure hold. For operations where repeatability and flexibility matter—such as machining centres, welding stations and assembly jigs—this clamp reduces the need for bespoke fixture redesigns when part families change. Durable construction for low maintenance and long service life Engineered for continuous industrial use, the mechanism is optimised for robustness and straightforward maintenance. The horizontal, heavy‑duty layout resists vibration and lateral forces typical in machining and welding environments, preserving clamp geometry and prolonging service intervals. Integration into existing fixtures is straightforward thanks to its standard dimensioning and the supplied counter‑holder; this simplicity supports predictable procurement and stocking. For customers seeking a dependable mechanical solution rather than frequent replacements, this clamp offers long‑term operational value. Contact Metav Werkzeuge today for bespoke advice on integrating the AMF toggle clamp 6849PH into existing fixtures; Metav’s specialists will advise on fixture layout, compatibility and delivery from Emmerich. Technical data Article number: 4000604389NW Model: 6849PH Product type: Toggle clamp Manufacturer: AMF Facts Maximum holding force: 15,000 N Adjustable stroke: 66 mm Clamping range (B): 42–107 mm E range: 24–90 mm H1: 122 mm L1: 130 mm S: 44 mm Special features Heavy‑duty horizontal toggle clamp Includes counter‑holder Size 4 Packaging unit: 1 FAQ What maximum holding force does the clamp provide? The AMF toggle clamp 6849PH delivers a maximum holding force of 15,000 N (SKU 4000604389NW), suitable for heavy‑duty fixturing and machining loads. Can the clamping height be adjusted for different part sizes? Yes; the clamp features an adjustable stroke of 66 mm and a clamping span that can be set within a 42–107 mm range to accommodate varying workpiece heights. Is this clamp suitable for horizontal mounting in a fixture? Yes. The device is a heavy‑duty horizontal toggle clamp intended for horizontal mounting in jigs, fixtures and production tooling. Does the delivery include a counter‑holder? Yes. The product is supplied including a counter‑holder, which improves repeatability and secures the mating surface. Which applications are typical for this toggle clamp? Common uses include machining fixtures, welding jigs and assembly stations where repeatable, strong clamping is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
150mm Closure Clamp Nr.6848H Horizontal With Counter Holder, Clamping Force 3200 N - AMF
Combining a maximum holding force of 3,200 N with a wide clamping range (B: 53.5–101 mm) and a horizontal layout with an integral counterholder, this locking clamp delivers secure, repeatable workholding for fixtures and jigs. Order the locking clamp directly via Metav Werkzeuge or consult the technical advisors if required. AMF 6848H Horizontal Locking Clamp, Size 3 The AMF 6848H is a horizontal locking clamp with an integrated counterholder, designed for secure fixture clamping and repeatable positioning in industrial production. Horizontal design with integral counterholder Wide clamping range B: 53.5–101 mm Max holding force 3,200 N Adjustable spindle M: 24.5–32.0 mm Secure, repeatable clamping for efficient production The horizontal locking device offers a high holding force of 3,200 N, ensuring components remain firmly fixed during machining or assembly. The combination of substantial clamping power and a wide clamping range (B from 53.5 mm to 101 mm) reduces the need for multiple clamp sizes and cuts changeover time. In practical terms, the listed values indicate the usable span for workpiece thickness and the clamp’s capability to resist displacement under process loads, delivering predictable and repeatable results on the shop floor. Fast setup and precise adjustment to reduce downtime Adjustment features such as the adjustable spindle (M: 24.5–32.0 mm) and the variable jaw positions allow quick fine-tuning during fixture setup. The clamp’s design supports straightforward alignment: L1 (169–216 mm) provides reach flexibility while H1 (70 mm) and H2 (135.5 mm) help integrate the unit into multi-clamp assemblies. These dimensional options promote efficient assembly of jigs, minimise rework and speed return to production following fixture changes. Robust horizontal layout that integrates into fixtures The horizontal layout with an integrated counterholder simplifies installation and ensures the clamping force is transmitted efficiently to the workpiece without unnecessary stress on surrounding components. Built to be incorporated into industrial fixtures, the unit’s compact profile and defined contact points support ergonomic tooling design and stable clamping cycles. The product is supplied as a complete item (packaging unit 1), enabling immediate integration into your tooling setup without additional components. For secure fixture clamping tailored to production workflows, request the AMF 6848H through Metav Werkzeuge’s specialist team in Emmerich; technical advisors are available at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 4123682300NW Type: 6848H Product: Locking clamp Execution: horizontal; including counterholder Label: Locking clamp No. 6848H Size 3 horizontal AMF Packaging unit: 1 Facts Holding force, max: 3,200 N Clamping range B: 53.5–101 mm E range: 48.6–96 mm L1: 169–216 mm L5: 93 mm M (adjustment): 24.5–32.0 mm H: 19 mm H1: 70 mm H2: 135.5 mm C: 19 mm D: 6.5 mm D1: 6 mm F: 14 mm K: 8.0 mm N: 48 mm P: 35 mm Special features Horizontal design Includes counterholder Size: 3 Wide adjustable range for versatile use Suitable for fixture and jig integration FAQ What clamping range does the clamp cover? The AMF 6848H offers a clamping range B from 53.5–101 mm, with an E range of 48.6–96 mm and an adjustable spindle M of 24.5–32.0 mm for fine tuning. How much holding force is available? Maximum holding force is 3,200 N for the AMF 6848H, providing strong and reliable fixation for typical fixture duties. Is the counterholder supplied with the clamp? Yes — the horizontal version is supplied including the counterholder as stated in the execution data. Which dimensions are most important for fixture integration? Key dimensions for integration include L1 (169–216 mm) for reach, H1 (70 mm) and H2 (135.5 mm) for clearance, and the clamping range B for workpiece thickness compatibility; these values support layout planning for the AMF 6848H. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
150mm Closure Clamp Size 1 Horizontal Adjustable 8mm Travel Zinc Plated Passivated, 2000N Holding Force - AMF
Benefit from a combination of robust clamping, a zinc-plated, passivated finish and a compact horizontal form factor that secures fixtures reliably in confined assemblies — order the item directly via Metav Werkzeuge or consult our advisors for application support. AMF Locking Clamp No. 6847 (Size 1) — Horizontal, Zinc-Plated AMF Locking Clamp No. 6847 is a horizontal locking clamp intended for fixture and jig applications where secure, repeatable holding and corrosion resistance are required Compact horizontal design for tight fixtures Max. holding force 2,000 N Zinc-plated, passivated finish for corrosion protection Adjustable travel 8 mm for precise clamping Consistent holding for repeatable production The horizontal locking clamp delivers reliable clamping through a rated holding force of 2,000 N, which defines the maximum static pull the device resists before release. That measurable value provides a clear basis for fixture design and risk assessment in machining or assembly operations. The clamp’s mechanism converts manual actuation into steady, repeatable clamping that reduces part movement during processing, improving quality and reducing rework. Engineers benefit from knowing the exact performance parameter when integrating the component into repeatable production lines. Space-saving horizontal layout and fine adjustment Designed as a compact horizontal design, this clamp suits confined jigs and bespoke fixtures where vertical clearance is limited. The device features an adjustable travel 8 mm, enabling small positional corrections without altering the base plate. Key dimensional ranges such as B1 16–23 mm and B2 35–42 mm allow straightforward planning of mounting points and mating parts. Clear numeric specifications support CAD integration and ensure that the clamp fits existing tooling with minimal modification, helping to speed up setup and reduce fixture redesign time. Corrosion-resistant finish with straightforward installation Surface treatment is zinc-plated and passivated, offering enhanced resistance to rust in workshop environments and contributing to longer service life with low maintenance. The construction and finish reduce surface degradation from coolant and workshop humidity, preserving clamping accuracy over time. As a size-rated component (size 1), it integrates into standard modular fixture systems and pairs well with common fasteners and locating elements. The combination of finish and mechanical design results in a durable, low-maintenance clamping solution for metalworking and assembly tasks. For a tailored quotation or technical clarification on the AMF horizontal locking clamp — including drawing compatibility and delivery from Metav Werkzeuge in Emmerich — contact Metav Werkzeuge by e‑mail at info@metav-werkzeuge.com or by telephone at +49 2822 7131930; our consultants will advise on integration and supply. Technical data Article number: 4000833520NW Type: 6847 Product: Locking clamp No. 6847, size 1, horizontal Manufacturer: AMF Packaging unit: 1 Dimensions / Performance Max. holding force: 2,000 N Adjustable travel: 8 mm B1: 16–23 mm B2: 35–42 mm C: 19 mm D: 5.3 mm E1: 17–24 mm E2: 35–42 mm G: 4.5 mm H: 22.7 mm H1: 34.5 mm H2: 111 mm K: 6 mm L: 31 mm L1: 62.6 mm M: 26–30 mm N: 40 mm R: 4.5 mm S: 45 mm Finish / Special features Finish: zinc-plated, passivated Orientation: horizontal Size classification: 1 Suitable for fixture and jig integration FAQ What holding capacity does the clamp provide? The clamp offers a maximum holding force of 2,000 N, a figure used to assess static retention in fixture designs for machining and assembly. Is the clamp adjustable for different workpiece thicknesses? Yes, the device features an adjustable travel of 8 mm, allowing fine positional adjustment to accommodate small differences in part geometry. What surface protection is applied to the clamp? The component is zinc-plated and passivated, providing corrosion resistance suitable for workshop environments. Can this clamp be mounted in tight or low-clearance setups? The horizontal design and compact dimensions such as L1 62.6 mm and B1 16–23 mm support installation in confined fixtures and modular jig assemblies. Which SKU identifies this specific model? This unit is listed under SKU 4000833520NW and is supplied as Locking clamp No. 6847, size 1, horizontal by AMF. Manufacturer: AMF; Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
150mm Closure Clamp Type 6848V Vertical With Counterholder, Max Hold 7000 N - AMF
Take advantage of the combination of a 7,000 N holding force, an adjustable clamping range (43–81 mm) and vertical installation for reliable, repeatable fixture results; order the unit via Metav Werkzeuge or consult our advisors for integration support. AMF Vertical locking clamp No. 6848V, Size 4 — vertical execution with keeper, 7,000 N holding force The AMF Vertical locking clamp No. 6848V, Size 4 is a vertically mounted closure clamp designed for secure, repeatable holding in jigs and fixtures and is supplied complete with its keeper. Vertical mounting with included keeper High holding force 7,000 N Adjustable clamping range 43–81 mm Robust design for industrial fixtures Reliable holding for repeatable clamping operations The vertical closure unit delivers consistent clamping performance where repeatability matters. With a maximum holding force of 7,000 N, the device secures components during assembly and testing to reduce slippage and rework. The mechanism is optimised for stable contact pressure, translating the mechanical properties of the clamp into predictable, measurable results for production processes. This makes it particularly suitable for fixture-heavy assembly lines and machining jigs that demand reliable part retention. Flexible adjustment and clear specification for easy integration A clearly defined adjustable clamping range (B 43–81 mm) and a set of precise dimensional reference points (for example H1 94.5 mm and H2 168 mm) simplify integration into existing tooling. The clamp’s dimensional data, including E 9–47 mm and M 35.0–46.0 mm, supports straightforward planning of stroke, clearance and contact geometry, so engineers can calculate compatible guides, stops and mating plates. These specifications reduce adaptation time and facilitate predictable fitment in modular fixture systems. Installation advantages and maintenance-friendly design The vertical orientation and included keeper support a compact footprint and simple mechanical interface. The execution “vertical; includes keeper” lowers installation complexity and shortens set-up time on production benches. Supplied as a single unit, the clamp avoids the need for additional matching parts during initial assembly. Routine maintenance is limited to visual inspections and ensuring the keeper and clamping surfaces remain free of heavy contamination to preserve repeatable clamping performance over long service intervals. Practical applications and where this clamp adds value This closure clamp is tailored for industrial clamping technology where secure retention and fast actuation are priorities — for example assembly jigs, transfer lines and testing fixtures. The combination of vertical mounting, adjustability and robust construction allows flexible use across small-batch production and series manufacturing. If any specification details require verification for a specific application, Metav’s technical advisors are available to discuss compatibility and installation strategies so the clamp integrates seamlessly into the existing process flow. Contact Metav Werkzeuge in Emmerich for technical advice or to arrange procurement of the AMF vertical locking clamp — eMail: info@metav-werkzeuge.com • Tel: +49 2822 7131930 Technical data Article number: 4123683400NW Type: 6848V Product: Vertical locking clamp (Verschlussspanner) Brand: AMF Execution: vertical, includes keeper Facts Holding force max: 7,000 N Size: 4 Clamping range B: 43–81 mm E range: 9–47 mm C: 32 mm D: 8.5 mm H1: 94.5 mm H2: 168 mm M: 35.0–46.0 mm L1: 151 mm N: 64.5 mm P: 53.5 mm Packaging unit: 1 Special features Vertical orientation; includes keeper Size 4 Supplied as a single unit Label: Verschlussspanner Nr.6848V Gr.4 vertikal AMF FAQ What is the maximum holding force of the clamp? The AMF Vertical locking clamp No. 6848V (Size 4) provides a maximum holding force of 7,000 N. What clamping range does the device cover? The closure clamp covers a clamping range B 43–81 mm, with E adjustable from 9–47 mm, enabling adaptation to a variety of workpiece thicknesses. Is a keeper included with the clamp? Yes — the unit is supplied vertically mounted and includes the keeper required for secure engagement. How is the clamp supplied and what is the packaging unit? The product is supplied as a single unit; packaging unit: 1. Which applications are suitable for this locking clamp? The clamp is intended for jigs, fixtures and assembly or test stations where repeatable clamping and high holding force are required. Manufacturer: AMF; Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
3 Size 3 Horizontal Toggle Clamp 12mm Travel Zinc Plated Passivated, 3000 N Holding Force - AMF
The compact design and 3,000 N holding force make this clamp a dependable choice for repeatable fixtures; the 12 mm adjustment travel ensures fast fine-tuning on the assembly line. Order the AMF locking clamp directly via Metav Werkzeuge or request consultation from our technical advisers for specification checks. AMF Locking Clamp No. 6847 (Size 3) – Horizontal, 3,000 N holding force The AMF Locking Clamp No. 6847 is a horizontal locking clamp for jigs, fixtures and assembly applications, designed to provide secure, repeatable clamping where space and adjustment precision matter. Zinc-plated, passivated corrosion protection Size 3 with 12 mm adjustment travel Max holding force 3,000 N Consistent, measurable clamping that keeps production moving The horizontal locking clamp delivers a repeatable clamping action with a certified holding force of 3,000 N, so workpieces remain fixed during machining and assembly operations. A defined holding force means process planners can rely on predictable clamping behaviour; this reduces scrap rates and decreases rework. The clamp’s mechanism is geared for short cycle times, with a 12 mm adjustment travel allowing quick compensation for part tolerances and enabling effective use in modular fixtures. Finish and durability to lower maintenance cycles The component is zinc-plated and passivated, a surface treatment that reduces corrosion and eases long-term maintenance in workshop environments. Passivation forms a controlled oxide layer that slows chemical attack, which is particularly useful in mildly humid or mixed-metal workshops. This finish minimises the need for frequent replacements or protective coatings, supporting uninterrupted production and lower lifecycle handling costs. Simple setup and precise alignment for fixture use Adjustment ranges and compact dimensions facilitate precise positioning. The clamp provides adjustable contact points and defined offsets that are compatible with common jig layouts, enabling fast installation and alignment on fixture plates. Fine adjustment capability means less reliance on shims and fewer trial-and-error cycles during initial setup, improving first-time-right rates for small- to medium-series manufacturing. Versatile application for industrial assembly and jigs As a horizontal locking clamp in size 3, the device is suited to repetitive assembly tasks, welding fixtures and test rigs where lateral securing is required. Its robust construction supports frequent actuation while maintaining positional stability. Delivered as a single unit, the clamp can be integrated into existing modular systems or used to upgrade bespoke tooling with minimal adaptation, supporting flexible production strategies. Contact Metav Werkzeuge for tailored advice and quick supply of the AMF locking clamp No. 6847 from our Emmerich warehouse Technical data Article number: 4000833521NW Type: 6847 Product: Locking clamp Label: Locking clamp No. 6847, size 3, horizontal, AMF Manufacturer: AMF Packaging unit: 1 UID: 4000833521NW Dimensions & core data Max holding force: 3,000 N Adjustment travel: 12 mm B1: 32–44 mm B2: 65–77 mm C: 19 mm D: 7.1 mm E1: 39–51 mm E2: 72–84 mm G: 5.5 mm H: 22.7 mm H1: 36 mm H2: 181 mm K: 13 mm L: 40 mm L1: 123.5 mm M: 31.5–35.5 mm N: 45 mm R: 5.5 mm S: 98 mm Design & special features Finish: zinc-plated; passivated Horizontal design for lateral clamping Size: 3 Compact form for fixture integration Single-piece delivery FAQ What is the maximum clamping force of the AMF locking clamp No. 6847? The AMF locking clamp No. 6847 provides a maximum holding force of 3,000 N, specified for stable fixturing in repetitive assembly and machining tasks. How much adjustment travel does the clamp allow? The clamp offers an adjustment travel of 12 mm to compensate for component tolerances and to simplify alignment during setup. Is the finish suitable for industrial workshop environments? Yes, the zinc-plated, passivated finish on the AMF locking clamp resists corrosion and reduces maintenance in typical workshop atmospheres. Can the clamp be mounted in compact fixture systems? The horizontal layout and compact dimensions (notably B1, B2 and L1 ranges) allow integration into modular plates and bespoke jigs without major redesign. What is included in the delivery? The item is supplied as a single unit (packaging unit 1) and is intended for immediate installation in fixture applications. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
3 Size 6847SU Closure Clamp With Safety Lock And Counterholder - AMF
Combining a holding force of 3,000 N with an integrated safety lock and an included counter-holder, this clamp delivers reliable horizontal fastening for jigs and fixtures. Order directly via Metav Werkzeuge or consult our advisors for application support and specification advice. AMF 6847SU locking latch clamp (horizontal) with safety lock A AMF 6847SU locking latch clamp for horizontal fastening tasks, featuring an integrated safety lock and supplied with a counter-holder for secure fixture closure Horizontal configuration with safety lock High holding force: 3,000 N Includes counter-holder for secure fastening Safer production through positive locking and high clamping force The horizontal configuration provides a compact solution where secure, repeatable fastening is required. With a holding force of 3,000 N, the clamp ensures components remain immobile during machining or assembly, reducing rejects and rework. The built-in safety lock prevents unintended release, which improves process safety and lowers the risk of workpiece displacement. For workplaces that prioritise stability and operator protection, this clamp adds a measurable layer of control to standard fixtures. Faster setup and consistent results with the included counter-holder Supplied complete with a counter-holder, the clamp simplifies jig integration and shortens set-up time. The counter-holder ensures correct alignment of the latch and distributes contact pressure for a secure closure, which benefits repeatable production runs and automated sequences. Using a single-purpose clamping unit of this type reduces the need for bespoke fixturing and speeds up changeovers, enabling more consistent cycle times and improved overall equipment effectiveness. Practical integration and expert support from Metav Werkzeuge Designed for quick incorporation into workshop tooling, the clamp supports horizontal fastening tasks in a wide range of fixtures. The robust functional concept keeps maintenance straightforward and helps to avoid downtime. Metav combines technical competence with a broad product range, offering tailored advice if specification clarification is required. If uncertain whether this clamp meets specific application demands, Metav’s team is available to advise on suitability and installation. Contact Metav Werkzeuge today for tailored advice on integrating the AMF 6847SU locking latch clamp into production; technical support and product guidance are available from our Emmerich team at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 4000604386NW Type: 6847SU Brand: AMF Product: locking latch clamp Core data Holding force: 3,000 N Size: 3 Packaging unit: 1 Features Horizontal configuration with safety lock Includes counter-holder Secure fastening for jigs and fixtures FAQ How strong is the clamping force of this latch clamp? The clamping force is 3,000 N for the AMF 6847SU locking latch clamp (SKU 4000604386NW), suitable for robust fixture retention. Does the delivery include a counter-holder? Yes, the AMF 6847SU is supplied inclusive of a counter-holder to ensure correct engagement and even pressure distribution. Is the clamp equipped with a safety mechanism to prevent accidental release? The AMF 6847SU features an integrated safety lock that secures the latch in position and prevents unintended opening during operation. Which orientation is this clamp intended for? This model is configured for horizontal use, optimised for fixtures and jigs that require lateral locking and compact mounting. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5 Size Closure Clamp Horizontal Zinc Plated Passivated, 5000 N Holding Force - AMF
Combines a galvanised, passivated finish with a 5,000 N maximum holding force and a 14 mm adjustable travel to deliver secure, repeatable clamping in jigs and fixtures — order directly via Metav Werkzeuge or contact our consultants for application advice. AMF 6847 Horizontal Latch Clamp, Size 5 — galvanised/passivated, 5,000 N The AMF 6847 horizontal latch clamp (size 5) is a robust locking clamp intended for fixture and jig applications where secure, repeatable clamping and corrosion protection are required. Galvanised, passivated corrosion-resistant finish Adjustable 14 mm clamping travel for precise positioning Maximum holding force 5,000 N for secure workholding Horizontal design for fixture and jig integration Long-term protection for workshop environments The galvanised and passivated surface treatment gives the latch clamp reliable corrosion resistance, reducing the need for frequent surface rework and extending service life in routine workshop conditions. For users working in production halls or maintenance bays, the protective finish minimises visible wear and helps maintain consistent contact geometry over time. This translates into fewer interruptions for part handling and a more predictable process flow. Measurable clamping power for stable processes With a maximum holding force of 5,000 N, this clamp provides a clearly defined performance level for securing components during machining, assembly or testing. The figure indicates the peak static retention capability under ideal engagement; in practice, this means improved resistance to slippage and better dimensional consistency for repeat operations. Performance-minded teams can rely on the documented holding force when designing fixtures or specifying safety margins. Fine adjustment for accurate positioning The built-in adjustable travel of 14 mm allows precise setting of the clamping point to suit varying workpiece heights or fixture tolerances. Adjustability ensures consistent contact pressure without over-stressing the component or the clamp mechanics, supporting repeatability in batch production. The horizontal orientation of the mechanism facilitates low-profile mounting and straightforward integration into existing jigs and tooling setups. Designed for quick integration and straightforward upkeep Constructed for workshop use, the latch clamp's geometry and size designation make it suitable for standard fixture layouts where a compact horizontal clamp is required. Maintenance needs are limited to routine inspection and light lubrication of pivot points; the protective finish reduces surface corrosion and helps preserve moving parts. Supply and ordering are simplified through Metav Werkzeuge, a long-standing partner for precision workshop equipment. For reliable fixture clamping, choose the AMF 6847 horizontal latch clamp and consult Metav Werkzeuge for tailored advice and ordering at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 4000833522NW Type: 6847 Product: Latch clamp Brand: AMF Finish: galvanised, passivated Packaging unit: 1 Facts Adjustment travel: 14 mm Maximum holding force: 5,000 N B1: 26–40 mm B2: 57–71 mm C: 29 mm D: 10.75 mm E1: 27–42 mm E2: 58–73 mm G: 11.2 mm H: 49 mm H1: 69 mm H2: 282 mm K: 13 mm L: 55 mm L1: 189.5 mm M: 55.5–63 mm N: 85 mm R: 8 mm S: 147 mm Special features Size: 5 Horizontal orientation Galvanised Passivated Product type: Latch clamp SKU: 4000833522NW FAQ What is the maximum holding force of this clamp? The AMF 6847 horizontal latch clamp (SKU 4000833522NW) provides a maximum holding force of 5,000 N. Does the finish protect against corrosion? The galvanised and passivated surface improves corrosion resistance for workshop use and helps maintain functional surfaces over time. Can the clamping stroke be adjusted to suit different workpieces? Yes, the clamping travel is adjustable and offers 14 mm of stroke to accommodate different part heights and tolerances. Is the clamp suitable for fixture mounting in a horizontal orientation? The design of this latch clamp is specifically for horizontal mounting in jigs and fixtures; the dimensional data (B1, B2, L1 etc.) should be used for precise layout and mounting decisions. What maintenance is recommended for long service life? Routine inspection of moving parts and light lubrication of pivots are recommended; the galvanised/passivated finish reduces the need for intensive surface maintenance. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
65mm Clamping Stroke Heavy-Duty Closure Clamp With Counterholder, 27 kN Holding Force - AMF
Take advantage of the heavy-duty horizontal design and 27,000 N maximum holding force to secure demanding workpieces reliably; the integrated counter-holder and generous 65 mm adjustment travel support efficient fixture setups — order directly via Metav Werkzeuge or consult our specialists for application advice. AMF 6849PH horizontal locking clamp (size 5) — heavy-duty, incl. counter-holder, 27 kN AMF 6849PH horizontal locking clamp (size 5) for heavy fixture clamping in assembly jigs and machining setups, offering a long adjustment range and robust holding capacity for industrial use Heavy-duty horizontal design Maximum holding force 27,000 N Adjustable travel 65 mm Includes counter-holder Reliable clamping power for heavy production tasks The AMF 6849PH horizontal locking clamp is engineered to deliver consistent clamping force under repeated cycles, making it suitable for demanding assembly and machining processes. With a maximum holding force of 27,000 N, the device secures larger or high-load components without additional bracing, which minimises rework and boosts process reliability. The robust horizontal configuration reduces interference with tooling and supports compact fixture layouts, enabling faster part loading and safer secured conditions during operations. Precise adjustment and quicker setup times The clamp provides an adjustable travel of 65 mm and a variable clamping range (B: 49–114 mm), which allows fine-tuning to a wide range of workpiece heights. This adjustability reduces the need for shims or repeated realignment and therefore shortens set-up time at the workbench. The included counter-holder ensures a secure counterpart for the latch mechanism, so clamping is immediate and repeatable — a practical advantage for batch work and series production where throughput matters. Built for durability and flexible workshop use Constructed as a heavy-duty unit and delivered with the counter-holder, this horizontal latch clamp resists the wear typical in industrial environments. The long lever and defined dimensions (e.g. H1: 146 mm, L1: 164 mm) support ergonomic handling and predictable kinematics in fixtures. The compact footprint and horizontally aligned actuator help maintain tool access and visibility, while the size 5 format balances force and installation space for a broad range of jigs and modular clamping systems. Choose the AMF locking clamp for reliable heavy-duty clamping and contact Metav Werkzeuge for tailored advice and prompt dispatch from Emmerich: info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 4000604390NW Type: 6849PH Product: Locking clamp Brand: AMF Execution: heavy; includes counter-holder Packaging unit: 1 Facts Size: 5 Adjustment travel: 65 mm B: 49–114 mm C: 57 mm D: 12 mm E: 28–93 mm F: 35 mm G: 10.5 mm H: 32 mm H1: 146 mm K: 12.5 mm L: 86 mm L1: 164 mm M: 57 mm N: 82 mm S: 47 mm Maximum holding force: 27,000 N Special features Heavy-duty horizontal design Includes counter-holder Robust construction for series use Compact horizontal actuator Size 5 format for versatile fixtures FAQ What is the maximum clamping force of this latch clamp? The maximum holding force of the AMF 6849PH horizontal locking clamp is 27,000 N, suitable for securing heavy workpieces in fixtures. Which adjustment range is available for height compensation? Height adjustment (travel) is 65 mm; the clamping range B covers 49–114 mm for flexible setup. Is a counter-holder supplied with the clamp? Yes, the unit is supplied including the counter-holder, which provides a secure mating surface for reliable latching. Can this clamp be used in confined fixture spaces? The horizontal actuator and compact dimensions (for example H1: 146 mm, L1: 164 mm) make the AMF 6849PH suitable for fixtures where tool access and space are constrained. Which product code identifies this clamp? The clamp is listed under SKU 4000604390NW and type 6849PH from AMF. Manufacturer: AMF / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com