10.5mm Knee Lever With 4.7mm Diameter, 0.1kg - Teknik Makina
The compact combination of a 4.7 mm pivot and 10.5 mm overall length ensures precise motion control in tight assemblies, while a 0.1 kg mass keeps handling and replacement straightforward. Benefit from a small, reliable toggle component designed for fixture use; order directly via Metav Werkzeuge or consult the technical team for application advice. Knee lever (Kniehebel) — Toggle lever with 4.7 mm pivot, 10.5 mm length by Teknik Makina The knee lever (Kniehebel) serves as a compact toggle component for clamping and actuation tasks in jigs, fixtures and mechanical linkages, offering a small footprint and defined pivot geometry for repeatable movement. Compact overall length 10.5 mm Precision pivot diameter 4.7 mm Lightweight construction, 0.1 kg Suitable for clamping and fixturing assemblies Space-saving design that reduces assembly complexity The small footprint of this toggle lever supports installation where room is limited. With an overall length of 10.5 mm and a pivot diameter of 4.7 mm, the component is intended for compact mechanical linkages and small-scale fixture elements. These dimensional values enable precise placement in confined assemblies, reducing the need for additional adaptors or extended linkages and therefore simplifying the overall assembly process. Fewer interface elements typically translate into lower cumulative tolerances and a more predictable motion response. Precise pivot geometry for consistent actuation A defined pivot diameter is a decisive factor in repeatable motion. The 4.7 mm pivot provides a clearly specified bearing surface that supports consistent kinematics in toggle and clamping sequences. In practical terms, this means improved positional repeatability and reduced play at the joint compared with unspecified or loosely dimensioned pivots. The modest mass (0.1 kg) contributes to controlled inertia during rapid cycles, helping to preserve alignment and reduce dynamic disturbance in small mechanisms. Integration and traceability for workshop and production environments Marked with SKU TL4ATM and produced by Teknik Makina, the lever is suitable for systematic stock-keeping and quick replacement workflows. The compact part size supports straightforward storage and logistic handling. Clear dimensional data (pivot Ø 4.7 mm, length 10.5 mm, weight 0.1 kg) enables rapid compatibility checks during design reviews and maintenance planning. Where repeatable clamping or actuation is required, specifying components with known measurements reduces downtime and simplifies spare-part management. For robust, space-conscious clamping choose the Teknik Makina TL4ATM knee lever — contact Metav Werkzeuge in Emmerich for product availability and engineering advice: info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: TL4ATM Manufacturer: Teknik Makina Weight: 0.1 kg Diameter: 4.7 mm Overall length: 10.5 mm Facts Pivot diameter: 4.7 mm Overall length: 10.5 mm Mass: 0.1 kg SKU: TL4ATM Special features Name: Kniehebel Brand: Teknik Makina FAQ What is the pivot diameter of the knee lever? The pivot diameter is 4.7 mm for the Tekniк Makina knee lever (TL4ATM), providing a defined bearing surface for repeatable motion. Can this lever be used in compact jigs and fixtures? Yes, the overall length of 10.5 mm and low mass (0.1 kg) make the TL4ATM suitable for compact jigs and small fixture assemblies where space is constrained. How is the part identified for ordering and stock control? The component is listed under SKU TL4ATM and attributed to Teknik Makina, which helps with traceability and spare-part logistics. Does the specification include weight and dimensions for design validation? Yes, the available specifications are weight 0.1 kg, pivot diameter 4.7 mm and overall length 10.5 mm, which can be used for mechanical integration checks. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
10.6mm Screw for Shim M6x12, Allen Key 4 Compatible - Teknik Makina
Take advantage of a compact, M6-threaded fastening solution with reliable fit and straightforward assembly; the combination of precise dimensions and Allen-key compatibility supports efficient workshop processes. Order the Screw for Shim directly via Metav Werkzeuge or consult the technical team for clarification. Screw for Shim – M6 thread, 12 mm overall length, Teknik Makina A Screw for Shim engineered for secure attachment of U-plates and shims in machine assemblies and workshop fixtures. M6 metric thread for standard fastening 12 mm overall length for compact assemblies 10.6 mm diameter for a precise fit Compatible with 4 mm Allen key Reliable fastenings where space is limited The fastening element is provided with an M6 metric thread and a 12 mm overall length, making it suitable for applications that require a compact, repeatable connection. The reduced length supports installations in confined assemblies while the standard thread size ensures compatibility with commonly used threaded holes and inserts. With a nominal head diameter of 10.6 mm, the component offers a precision fit that reduces play and minimises the need for rework during assembly. The design focuses on operational efficiency and predictable mechanical behaviour under normal workshop conditions. Efficient handling and straightforward assembly Assembly is simplified by the requirement for a 4 mm Allen key, a common tool in industrial and maintenance settings. This compatibility shortens assembly time and reduces tool variance across production lines. The fastener’s configuration supports quick engagement with U-plate and shim interfaces, promoting consistent clamping force and ease of replacement when adjustments are necessary. The clear specification of drive interface and thread geometry aids inventory management and streamlines procurement for purchasing teams seeking dependable, standardised components. Suitable for workshop and fixture applications Intended for use in fixture construction and equipment maintenance, this fastening part is optimised for repeatable installation cycles and mechanical stability in smaller-scale assemblies. The compact geometry helps to maintain clearance around moving parts while providing secure retention for shims and U-plates in positional applications. Specified dimensions and drive type enable predictable interchangeability with other M6 fasteners used across the workshop, supporting a reduction in variant stock and simplifying repair procedures. The product is supplied by Teknik Makina and aligns with standardised workshop practices. For reliable M6 fastening from Teknik Makina, request availability or place an order through Metav Werkzeuge — contact the Metav technical team for product matching and delivery from Emmerich. Technical data Article number: TC039TM Manufacturer: Teknik Makina EClass: 21189290 SKU: TC039TM Dimensions & core data Thread: M6 Diameter: 10.6 mm Overall length: 12 mm Weight: 0.1 kg Special features & compatibility For shim / for U-plate Compatible with 4 mm Allen key Suitable for standard M6 threaded holes FAQ What thread specification does this fastener use? The fastener uses an M6 metric thread; the Screw for Shim (Teknik Makina, SKU TC039TM) is specified for standard M6 applications. What are the key dimensions of the part? Key dimensions are a 10.6 mm diameter and 12 mm overall length; the listed weight is 0.1 kg for the item as supplied. Which tool is required for installation? Installation requires a 4 mm Allen key, which matches the internal hex drive specified for the component. Is this component intended for U-plates and shims? Yes; the item is described for use for shim / for U-plate, offering a compact fastening solution for those applications. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
10mm Screw for End Mill M5, Inbus Key T20 - Teknik Makina
Secure, precise fastening for end mill tooling is achieved with the combination of an M5 thread and a compact 10 mm overall length, delivering dependable clamping and reduced tool movement during milling operations. Order the component directly via Metav Werkzeuge or consult our specialists for matching to specific tool holders. Screw for End Mill TC174TM — M5 thread, 10 mm overall length (Teknik Makina) The Screw for End Mill TC174TM is a compact fastening component designed to secure end mill cutters in standard tool holders for stable machining in workshop and production environments. M5 thread for standard tool holders 10 mm overall length for compact clamping 7 mm diameter for precise seating Hex key T20 drive for secure tightening Secure clamping for reliable machining This fastening component uses an M5 thread and a 10 mm overall length to provide a tight connection between cutter and holder, improving stability during milling. The hex key T20 drive ensures reproducible tightening, which helps to minimise axial play and vibration. In a cutting-tool context, consistent clamping directly supports better surface finish and longer tool life; the component is therefore a simple, effective measure to increase process reliability. The product is manufactured by Teknik Makina and designed for integration with common end mill holders. Seamless integration into cutting tool workflows Compatibility with standard holders is indicated by the M5 specification and the 7 mm seating diameter, allowing the part to work with a wide range of end mill assemblies. The compact form factor reduces interference in tight setups and facilitates rapid replacement during tool changes. Routine maintenance is straightforward: removal and reinstallation with a hex key T20 avoids specialised equipment. If confirmation of fit is required, Metav Werkzeuge can assist with technical matching to existing holders and clamping systems for a seamless workshop workflow. Practical handling and workshop guidance Weighing 0.1 kg, the component is compact and easy to handle while still offering robust mechanical engagement for small to medium-sized milling operations. Installation requires a hex key T20 and controlled tightening to avoid overloading the thread; correct tightening improves concentricity and helps to limit runout in the tool assembly. For workshops seeking dependable, repeatable clamping solutions, this screw provides a low-complexity option that supports uptime and consistent machining results. For technical matching and secure supply of Teknik Cutting Tools fastening components, contact Metav Werkzeuge in Emmerich — phone +49 2822 7131930 or email info@metav-werkzeuge.com — our consultants will advise on compatibility and delivery. Technical Data Article number: TC174TM Designation: Screw for End Mill ECLASS: 21189290 Manufacturer: Teknik Makina Facts Thread: M5 Diameter: 7 mm Overall length: 10 mm Weight: 0.1 kg Special features Drive: Hex key T20 Suitable for end mill holders SKU: TC174TM FAQ Will this screw fit standard end mill holders? The screw TC174TM is specified with an M5 thread and a 7 mm seating diameter, which fits many standard end mill holders; verification against the holder thread and seating dimensions is recommended. What tool is required to install the screw? A hex key T20 is required to tighten the Screw TC174TM; the hexagonal recess provides reproducible torque application for secure clamping. What are the key dimensions of the component? Key dimensions: M5 thread, 7 mm diameter, 10 mm overall length, weight 0.1 kg; the SKU is TC174TM for ordering and reference. Is the material of the screw specified? Material is not specified in the available product data for the Screw TC174TM; material information should be confirmed with Metav Werkzeuge if required for specific applications. How does this screw affect machining quality? By providing a secure, correctly seated connection in the tool holder, the Screw TC174TM helps to reduce axial play and vibration, supporting improved surface finish and repeatability in milling operations. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
10mm Screw for Shim M3 Thread, 5.6mm Diameter - Teknik Makina
Take advantage of the combination of M3 thread security, compact 10 mm length and precise Ø 5.6 mm seating to ensure reliable clamping for insert assemblies; order directly via Metav Werkzeuge or consult the team for specification advice. Screw for Shim (TC036TM) — M3 thread, 10 mm overall length, Teknik Makina A Screw for Shim engineered for reliable clamping of shims and small insert assemblies in compact toolholders and fixtures. Precise M3 thread for secure clamping Compact 10 mm overall length for tight fits Diameter 5.6 mm for accurate seating Compatible with T10 hex key for quick tightening Robust clamping through a precise metric thread The fastener relies on a M3 thread, a metric standard commonly used in tooling for its balance of strength and fine adjustment. This thread choice supports secure clamping and improved repeatability of seating forces in indexable insert assemblies, reducing micro‑movement during cutting operations. The metric specification simplifies component selection in mixed fleets and allows predictable torque control when using calibrated drivers. The result is a dependable connection between shim and holder that contributes to consistent machining outcomes. Space-saving form that suits compact toolholders With an overall length of 10 mm and a seating diameter of 5.6 mm, the screw is designed to fit tight envelopes without compromising clamping integrity. The short profile makes it appropriate for low‑clearance applications and specialised holders where longer fasteners would interfere with tool geometry. That compact footprint helps maintain the intended toolpath and minimises the need for design compromises when assembling small, high‑precision tooling systems. Simple installation and workshop efficiency Installation is straightforward: the connection is compatible with a T10 hex key, enabling fast assembly and repeatable torque application with commonly available hand tools. Precision machining of the component supports consistent thread engagement and long service intervals, reflecting the product's background in high-class steel machining. For procurement and routine maintenance, the compact fastener reduces inventory complexity while supporting efficient changeover procedures on the shopfloor. For specification support or to procure TekniK Cutting Tools components supplied via Metav Werkzeuge, contact our specialists in Emmerich for personalised advice and dependable dispatch from stock. Technical data Article number: TC036TM Name: Screw for Shim (Screw for U-Plate) Brand: Teknik Makina Numbers / Core technical data Diameter: 5.6 mm Thread: M3 Overall length: 10 mm Weight: 0.1 kg Special features Compatible with shims / for Shim For clamping indexable inserts Compatible with T10 hex key High-class steel machining; long service life FAQ What thread standard is used for this fastener? The fastener uses a metric M3 thread; the Screw for Shim (TC036TM) follows common metric clamping standards for small tooling components. Which driver is required to tighten the screw? A T10 hex key is specified for assembly, providing quick installation and repeatable torque application. Is this fastener suitable for securing shims in insert holders? Yes, the design is intended for use with shims and indexable insert clamping where compact, secure fastening is required. What are the key dimensions of the part? Key dimensions: diameter 5.6 mm, thread M3, overall length 10 mm, weight 0.1 kg (TC036TM). Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
10mm Screw For Shim M3.5 Thread, T15 Hex Key Compatible - Teknik Makina
The compact metric design combines precise M3.5 thread with a short 10 mm overall length for secure shim and U‑plate fastening; the standard compatibility with a hex key T15 streamlines assembly and reduces downtime. Order directly via Metav Werkzeuge or contact our consultants for compatibility advice. Screw for Shim TC040TM (M3.5, 10 mm) by Teknik Makina A screw for shim intended for secure fastening of U‑plates and shims in compact workshop and industrial fixtures. Compact M3.5 fastening element 10 mm overall length for tight assemblies Compatible with hex key T15 For U-plate and shim mounting Precise metric threading for dependable clamping The compact fastener is engineered with a M3.5 thread to ensure consistent engagement in metric fixtures. The standardised thread profile delivers predictable torque behaviour and repeatable clamping force, which supports reliable assembly processes and reduces the need for rework. As a small-format fixing element, it suits tight assemblies where controlled thread depth and clearance are essential, enabling secure retention of shims and U‑plates without overhanging components. This results in fewer stoppages and a more stable production flow. Quick installation with common workshop tools Installation is designed to be straightforward: the fixing accepts a hex key T15, allowing teams to work with familiar hand tools and torque drivers. The compatibility with common tools shortens setup time and simplifies maintenance tasks, contributing to faster changeovers in batch production or repair operations. Where repeatable tightening is required, the geometry facilitates even torque transfer, so fixtures remain stable under vibration and operational loads. This practical tool interface supports efficient workflows across workshops. Compact form for versatile fixture applications With an overall length of 10 mm and a nominal diameter of 8 mm, this fastener is tailored for confined installation spaces and low-profile clamping points. The low mass and modest dimensions make it suitable for assemblies where bulk must be avoided while maintaining secure anchorage. The component integrates easily into standard shim and U‑plate assemblies and aligns with common industrial part standards, providing interchangeability and ease of planning. For traceability and ordering, the item is listed under SKU TC040TM and originates from Teknik Makina, a recognised producer of precision fixing components. For specification checks, compatibility confirmation or to order the Teknik Makina TC040TM screw via Metav Werkzeuge, please contact Metav Werkzeuge and our technical advisors will assist promptly. Technical data Article number: TC040TM SKU: TC040TM Facts Diameter: 8 mm Thread: M3.5 Overall length: 10 mm Weight: 0.1 kg eClass: 21189290 Special features Suitable for shim / U‑plate mounting Compatible with hex key T15 Manufacturer: Teknik Cutting Tools FAQ What thread type does this fastener use? The screw uses an M3.5 thread, as specified for the Teknik Makina TC040TM fixing element, providing standard metric engagement for compatible fixtures. Is this part suitable for U‑plate and shim applications? Yes, the design is intended for shim and U‑plate mounting; the geometry and length support low‑profile clamping in such assemblies. Which tool is required for installation? Installation requires a hex key T15, allowing use of standard workshop hex keys or compatible torque drivers with the Teknik Makina TC040TM. How is the item identified for ordering? Order using SKU TC040TM; the part is supplied by Teknik Makina and stocked for straightforward procurement. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
10mm Screw for Shim M4 Thread, 7.3mm Diameter - Teknik Makina
Take advantage of robust metric compatibility and a compact format to secure shims and U-plates with minimal assembly height; order directly via Metav Werkzeuge or consult our specialists for procurement and supply from Emmerich. Screw TC038TM – M4 thread, 10 mm overall length (Teknik Makina) A Screw TC038TM engineered for fastening shims and U-plates in compact assemblies within general workshop and clamping applications. M4 metric thread standard fitting 10 mm overall length for low-profile joints 7.3 mm nominal diameter for reliable seating Compatible with T15 hex key for installation Reliable metric fastening with proven compatibility The TC038TM is specified with an M4 metric thread and a 7.3 mm nominal diameter, which delivers a consistent fit with standard threaded holes and inserts. The use of a standard metric thread simplifies parts sourcing and replacement across toolrooms and production cells; this compatibility reduces downtime and streamlines inventory management. In practical terms, the defined geometry enables predictable clamp forces and repeatable assembly behaviour, which supports efficient process planning in small-series production and maintenance tasks. Low-profile design that reduces interference in assemblies With an overall length of 10 mm, this fastening element offers a compact design ideal for situations where protrusion must be minimised. The shorter length helps prevent collisions with neighbouring components and reduces lever arms that can induce bending moments under load. Combined with the nominal diameter, the profile ensures secure seating in shims and U-plate connections without excess material above the mating surface. Where space and clearance are at a premium, this configuration supports neater, safer mechanical joints. Straightforward installation and dependable performance Assembly is designed to be efficient: the screw integrates with a T15 hex key, enabling controlled torque application with commonly available tools. The specified tool interface supports consistent tightening and helps avoid cross-head damage or slippage during installation. At a measured mass of 0.1 kg, the component is easy to handle in manual and semi-automated workflows, while the clear specification facilitates purchasing and quality checks. Supplied by Teknik Makina and distributed via established supply channels, the part is suitable for workshops and stockrooms that prioritise traceable, standardised components. Contact Metav Werkzeuge for a tailored procurement proposal for the Teknik Cutting Tools TC038TM screw, including delivery options from our Emmerich stock and advice on matching fasteners to specific shim or U-plate assemblies Technical data Article number: TC038TM Manufacturer: Teknik Makina Facts Diameter: 7.3 mm Thread: M4 Overall length: 10 mm Weight: 0.1 kg eCl@ss: 21189290 Special features Application: for shim / U-plate fastening Compatible tool: T15 hex key Product type: metric screw FAQ What thread size does this screw use? The screw uses an M4 metric thread; the TC038TM by Teknik Makina is specified for standard M4 fittings. Is the screw suitable for securing shims or U-plates? Yes, the TC038TM is designed for fastening shims and U-plates and is listed with the application “for shim / U-plate”. Which installation tool is required for this fastener? Installation requires a T15 hex key, enabling controlled torque when fitting the TC038TM screw. What is the overall length and nominal diameter of the part? The part has an overall length of 10 mm and a nominal diameter of 7.3 mm, suitable for low-profile assemblies. Can this component be sourced through Metav Werkzeuge? The TC038TM screw from Teknik Makina is available via Metav Werkzeuge; procurement can be coordinated from the Emmerich stock. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
10mm Screw for Shim M6, 10mm Length - Teknik Makina
Take advantage of a compact fastening solution that combines M6 compatibility, a short 10 mm overall length and a hex socket designed for a 4 mm Allen key to simplify assembly of shims and U‑plates; order directly via Metav Werkzeuge or consult our specialists for specification matching. Screw for Shim — M6 x 10, hex socket (Teknik Makina) A Screw for Shim intended for secure fastening in shim and U‑plate assemblies, offering a standard M6 thread and a short profile suited to tight fixture geometry. M6 thread for standard fastening 10 mm overall length Hex socket for 4 mm Allen key Suitable for shim and U‑plate fastening Precise fastening where space is limited and repeatability matters The compact fastener's M6 thread and 10 mm overall length make it ideal for installations where a low-profile connection is required. The short thread engagement reduces protrusion yet provides reliable clamping when used in shims and U‑plates, helping maintain alignment without adding bulk. The hex socket design ensures consistent torque application with a 4 mm Allen key, improving assembly repeatability and reducing the risk of over‑tightening that can damage thin components. These measurable attributes support inventory standardisation and simplify maintenance planning. Designed for efficient workshop workflows and quick maintenance With a lightweight specification of 0.1 kg and compatibility with a common 4 mm Allen key, the fastener integrates smoothly into existing tooling sets and service procedures. The hex drive allows quick insertion and removal in confined spaces, accelerating setup changes and on‑bench adjustments. For production environments and repair benches alike, the combination of standard thread form and simple drive interface minimises downtime and keeps fixture changes predictable and fast. Built by a recognised manufacturer for dependable sourcing Produced by Teknik Makina, this fastener benefits from consistent manufacturing tolerances that are important for repeat applications and batch replenishment. Where traceability and supplier reliability matter, selecting a component from an established provider reduces procurement risk and supports long‑term spare parts planning. The screw’s straightforward specification also aids compatibility checks when replacing damaged fasteners in assembly jigs or when consolidating parts across different workstations. Practical compatibility and inventory advantages The product is tailored to fastening shims and U‑plates and pairs with standard workshop tools, making it a practical choice for maintenance teams and production planners seeking to limit part variants. Its M6 sizing aligns with widely used metric systems, supporting easier cross‑referencing with existing drawings and BOMs. The compact profile is particularly useful where clearance above the mating surface is constrained, delivering a secure connection without unnecessary material thickness. Contact Metav Werkzeuge for procurement and technical matching of the Teknik Makina M6 x 10 screw for shim applications — call +49 2822 7131930 or email info@metav-werkzeuge.com for expert advice and rapid supply from our Emmerich warehouse Technical data Article number: TC049-1TM Manufacturer: Teknik Makina Designation: Screw for Shim Dimensions & core data Thread: M6 Overall length: 10 mm Weight: 0.1 kg Hex key: 4 mm Allen Materials & features Application: for shim and U‑plate fastening Drive type: hex socket Drive tool compatibility: 4 mm Allen key FAQ What thread and length does this screw have? The screw is specified with an M6 thread and an overall length of 10 mm, suitable for compact fastening tasks and shim assemblies. Which tool is required to install the screw? Installation uses a 4 mm Allen key engaging the screw's hex socket for consistent torque application. Is this part suitable for securing shims and U‑plates? Yes, the design is intended for shim and U‑plate fastening and provides a low‑profile connection in such assemblies. Who manufactures this screw and how is it identified? The component is produced by Teknik Makina and can be identified by SKU TC049-1TM for ordering and replenishment. Can this fastener be used with standard M6 tapped holes? The screw's M6 thread is compatible with standard metric M6 tapped holes when appropriate thread engagement is provided. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
10mm Toggle Lever Adjustable Clamping Knee Lever - Teknik Makina
Take advantage of the compact 3 mm diameter, low-profile 10 mm length and lightweight construction to improve fixture layouts and reduce moving mass; order directly via Metav Werkzeuge or consult the technical team for integration advice. Knee lever (Kniehebel) — low-profile toggle lever by Teknik Makina, 3 mm Ø · 10 mm length A Knee lever (Kniehebel) engineered for compact clamping and toggle applications in jigs and fixtures, offering a small footprint and consistent actuation for space-constrained assemblies Compact 3 mm diameter for tight spaces Total length 10 mm for low-profile mounting Lightweight 0.1 kg reduces inertia Space-saving design for denser assemblies The small 3 mm diameter and 10 mm overall length ensure a minimal footprint, allowing denser placement of clamping elements on a mounting plate. This low-profile geometry reduces lateral interference and simplifies fixture layouts, which in turn shortens set-up time and increases usable workspace. The compact form is particularly beneficial where multiple levers must be arranged in parallel; it enables a tidy, efficient arrangement without compromising accessibility or mechanical function. Consistent actuation and reliable toggle motion A compact toggle lever delivers repeatable clamping strokes and a firm mechanical lock when engaged. The design prioritises precision and consistent mechanical travel, which helps maintain part positioning across repeated cycles. For production-oriented fixtures, consistent actuation reduces rework and inspection effort. The lever’s modest mass contributes to smooth operation, lowering wear on pivots and connected hardware and supporting longer intervals between maintenance checks. Easy integration into existing tooling The lever’s dimensions and straightforward geometry make it suitable for retrofitting or new fixture builds. Its lightweight nature minimises load on pivot mounts and drives, facilitating straightforward attachment to plates or sub-assemblies. Where compact toggle action is required, this lever can be incorporated with minimal design changes, saving engineering time. Technical teams will appreciate the clear, measurable specifications when planning mounting points and clearances. For procurement and technical advice on the Teknik Cutting Tools knee lever TL3BTM, contact Metav Werkzeuge in Emmerich for tailored guidance and fast supply: info@metav-werkzeuge.com | +49 2822 7131930 Technical Data Article number: TL3BTM Manufacturer: Teknik Makina Dimensions & weight Diameter: 3 mm Total length: 10 mm Weight: 0.1 kg eClass: 21189290 Design & application Product: Knee lever (Kniehebel) Typical application: compact clamping and toggle fixtures FAQ What are the exact dimensions of the lever? The lever has a diameter of 3 mm and a total length of 10 mm; it is listed under SKU TL3BTM. Is the lever suitable for low-profile fixtures? Yes, the knee lever TL3BTM is designed for low-profile mounting and compact fixture arrangements. How much does the component weigh? The component weight is 0.1 kg, which supports reduced moving mass in assemblies. Can this lever be integrated into existing jig designs? Integration is straightforward thanks to the lever’s compact geometry and measurable dimensions, allowing easy retrofitting into jigs and fixtures. Who manufactures the lever and where does support come from? The lever is produced by Teknik Makina and supplied via Metav Werkzeuge; see the manufacturer details below for full contact information. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
10mm Torx Screw M3 5.3mm Diameter 55° Angle, T15 Hex Key Compatible - Teknik Makina
A compact fastener combining a M3 thread, a 55° countersunk head and a 5.3 mm head diameter ensures secure, flush-mounted joints in small assemblies; specified length 10 mm gives reliable clamping without excess protrusion. Order the Torx screw directly via Metav Werkzeuge or ask our consultants if needed. Torx screw — M3 × 10 mm, 55° countersunk head | Teknik Makina The Torx screw is a precision fastener for small assemblies that requires secure torque transfer and a flush, finished surface. M3 thread for compact assemblies 55° countersunk head for flush finish Compatible with Torx T15 key 10 mm overall length for tight joins Consistent torque transmission for reliable joints The Torx geometry is engineered to reduce cam‑out and to enable higher torque transfer compared with slotted or Phillips heads. With an M3 thread, this fastener is suitable for delicate mechanical assemblies and small equipment where thread engagement and repeatable clamping are essential. The internal drive geometry paired with the Torx T15 compatibility allows controlled tightening with torque drivers or hand keys, improving assembly repeatability and reducing the risk of fastener or tool wear. Flush mounting that preserves form and function A 55° countersunk head produces a discreet, level surface once installed; the specified 5.3 mm head diameter is sized to sit neatly in standard countersinks for small components. This design avoids protruding heads that catch on adjacent parts or interfere with sliding elements. For production and service technicians, the result is both a tidy aesthetic and a functional advantage: smoother assemblies and fewer clearance issues during operation. Straightforward specification and workshop compatibility The overall length of 10 mm and the M3 thread simplify part selection and stock management for repeat jobs and maintenance. The fastener is compatible with common Torx tools, streamlining assembly processes across different workstations. Clear specification reduces ordering uncertainty and shortens setup times on production lines, providing a pragmatic efficiency benefit for workshops and small series manufacturers. Proven sourcing and dependable supply for industry use Supplied by Teknik Makina, the fastener reflects industry‑grade production standards suitable for routine and precision applications. Sourcing through a trusted distributor ensures consistent availability and quality control, supporting uninterrupted workflows. Metav’s role as a quality filter for the European market further underlines dependable logistics and expert procurement support for workshop and industrial customers. For technical guidance on suitability or to secure Teknik Makina Torx screws via Metav Werkzeuge — contact the Metav sales team for expert advice and precise delivery from Emmerich Technical data SKU: TC066TM ECLASS: 21189290 Brand: Teknik Makina Article: Torx screw Facts Weight: 0.1 kg Diameter: 5.3 mm Thread: M3 Overall length: 10 mm Angle: 55° Special features Compatible with Torx T15 key 55° countersunk head Fastener type: Torx screw Intended for small assemblies FAQ What drive tool fits this screw? The screw is compatible with a Torx T15 drive; Teknik Makina specifies Torx T15 for reliable engagement and torque transfer (SKU TC066TM). Is the head suitable for countersinking? Yes. The 55° head angle provides a countersunk geometry designed for a flush finish when installed in a matched countersink. What sizes and thread form does this fastener use? This fastener is specified with an M3 thread, a 5.3 mm head diameter and an overall length of 10 mm as indicated for small‑scale assemblies. Can this screw be used in precision equipment? Its Torx drive and M3 thread make the screw appropriate for precision and small mechanical assemblies where controlled torque and repeatable clamping are required. Who manufactures this screw and who handles distribution? Teknik Makina is the manufacturer; distribution and procurement for European customers are handled via Metav Werkzeuge with reliable delivery from Emmerich. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
11.2mm Locking Screw M6 14mm Overall Length, For Indexable Inserts - Teknik Makina
Compact and robust, the locking screw combines a M6 thread with a precise 11.2 mm seat to secure indexable inserts reliably; its 14 mm overall length and compatibility with a 3 mm Allen key make installation and maintenance straightforward. Order the locking screw directly via Metav Werkzeuge or consult our experts for an application-specific recommendation. Locking screw TC050TM — Locking screw for indexable inserts, M6 thread, 11.2 mm (Teknik Makina) The Locking screw TC050TM secures indexable inserts in turning and milling clamping systems, designed for compact, repeatable clamping in production environments *Locking screw for indexable inserts M6 thread *11.2 mm diameter for precise seat alignment *14 mm overall length for compact clamping *Operated with 3 mm Allen key for easy tightening Reliable clamping that reduces rework and stoppages A compact locking screw with an M6 thread and a finely controlled 11.2 mm seat diameter delivers consistent clamping force that helps prevent insert movement during machining. The stable connection improves repeatability, which in turn reduces the risk of rework and unscheduled stops. With a modest mass of 0.1 kg, the component contributes negligible inertia yet provides a positive mechanical connection; its 14 mm overall length suits tight toolholder geometries and keeps the tool assembly compact. Fast service intervals and simple workshop handling Maintenance and replacement are straightforward thanks to the standard 3 mm Allen key interface, enabling rapid intervention during tool changes or routine checks. Fewer specialised tools are required, which simplifies stockholding and shortens turnaround times in busy workshops. The straightforward geometry of the fastener reduces the likelihood of cross-threading and saves time during assembly, supporting predictable maintenance cycles and smooth production flow. Compatibility that supports standardisation and supply reliability Designed as a practical fastening solution for indexable inserts, the component aligns with common clamping concepts used across turning and milling toolholders. Sourcing through Metav Werkzeuge ensures access to a broad supply chain and a quality filter based in Emmerich, which supports timely deliveries and consistent product quality. The part is manufactured by Teknik Makina and listed under SKU TC050TM, providing clear traceability for procurement and inventory management. For procurement or application advice relating to this Teknik Makina locking screw, contact Metav Werkzeuge for tailored recommendations and reliable supply solutions Technical data Article number: TC050TM Name: Locking screw for indexable inserts Manufacturer: Teknik Makina Facts Diameter: 11.2 mm Thread: M6 Overall length: 14 mm Weight: 0.1 kg Compatibility & operation Operated with 3 mm Allen key Suitable for indexable inserts Intended for compact clamping systems FAQ What is the thread size of the locking screw? The locking screw TC050TM is specified with an M6 thread for secure clamping in standard insert holders. Which tool is required to operate the fastener? Assembly and removal are performed with a 3 mm Allen key, matching the design of the locking screw. Is the fastener suitable for compact toolholders? Yes, the 14 mm overall length and 11.2 mm seat diameter make the fastener appropriate for confined clamping geometries. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
11mm 5.2mm Torx Screw M4 45° Angle, T15 Hex Key Compatible - Teknik Makina
Compact, reliable fastening with a secure Torx head and standard M4 metric thread — the small form factor (Ø 5.2 mm, length 11 mm) makes it well suited for precise assemblies and repeatable production processes. Order via Metav Werkzeuge or consult the technical team for batch supply and specification matching. Torx Screw TC079TM — M4 thread, 5.2 mm diameter | Teknik Makina Torx Screw TC079TM — a compact fastening solution for workshop and industrial assemblies, engineered for consistent drive engagement and standardised metric threading. Secure Torx head for positive drive M4 metric thread for standard assemblies 5.2 mm diameter for tight fit tolerances 11 mm overall length for compact applications Consistent drive performance for efficient assembly The Torx head profile delivers a reliable contact surface that reduces cam‑out and allows higher torque transmission compared with conventional recessed drives. For production environments where tool changeover and assembly speed matter, this profile supports repeatable torque application and lowers the risk of damaged fastener heads. Compatibility with a Torx key T15 ensures the component integrates seamlessly into standard driver sets and assembly fixtures. Metric thread stability to maintain joint integrity With an M4 metric thread, the fastener conforms to widely accepted metric systems used across mechanical assemblies. The combination of the M4 thread and the measured shank diameter of 5.2 mm provides predictable engagement and thread pitch behaviour, which simplifies torque settings and quality control. Using standardised components like this screw reduces the need for bespoke fasteners, aiding inventory management and procurement efficiency for production and maintenance teams. Small size, big application range The compact 11 mm overall length and a head angle of 45° (where applicable) make this screw particularly useful where space is restricted or where flush or near‑flush seating is required. Although the material is not specified in the data set, the dimensional accuracy and the Torx drive render the part suitable for precision fastening tasks in general workshop assemblies and light machinery. Batch procurement via an established distributor supports consistent supply and reduces lead‑time variability. Contact Metav Werkzeuge for quantity supply, specification matching or to discuss suitable driver options for the Teknik Makina Torx Screw TC079TM — phone +49 2822 7131930 or eMail info@metav-werkzeuge.com Technical data Article number: TC079TM Brand: Teknik Makina ECLASS: 21189290 ** Dimensions & measurable data Diameter: 5.2 mm Thread: M4 Overall length: 11 mm Head angle: 45° Weight: 0.1 kg ** Design & special features Torx head profile Suitable for Torx key T15 Metric thread standard Compact length for tight assemblies ** FAQ What driver is required for this Torx screw? A Torx key T15 is specified as the compatible driver for this Torx screw; using the correct T15 driver ensures secure engagement and consistent torque transfer. Is the thread size compatible with DIN standard components? The fastener uses an M4 metric thread, which aligns with common metric component standards and simplifies integration with standard nuts and pre‑tapped holes. Can this screw be used where space is limited? Yes — the 11 mm overall length and compact diameter make it suitable for confined assemblies and applications requiring near‑flush fastening. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
11mm Locking Screw M6 27mm Total Length, Hex Key 3mm - Teknik Makina
Take advantage of a compact, mechanically reliable locking solution that combines a standard M6 thread with easy operation via a 3 mm Allen key for consistent measurement retention; order spares or discuss fitting options through Metav Werkzeuge's consultants. Locking screw TC044TM — M6 thread, Allen key operation (Teknik Makina) Locking screw TC044TM for precision calipers and measuring tools, designed to secure sliding parts and prevent unwanted movement during measurement. M6 thread for secure fastening Operated with 3 mm Allen key 11 mm diameter for compact fit 27 mm total length for standard integration Secure fixation for stable measurements A reliable locking fastener delivers measurable benefits for workshop metrology: the M6 thread ensures a firm connection that resists slippage under normal handling, while the 3 mm Allen key operation enables controlled torque application without specialised tools. By preventing unintended axial movement, the locking screw TC044TM contributes directly to improved repeatability and stable measurement results in routine inspection tasks. In production environments where incremental errors accumulate, a dependable locking fastener reduces rework and supports consistent quality control. Compact dimensions that simplify retrofitting With an external diameter of 11 mm and a total length of 27 mm, the component is engineered for straightforward integration into common caliper designs and measuring fixtures. The modest weight of 0.1 kg minimises added mass to sliding assemblies and helps maintain instrument balance. These compact dimensions mean the part occupies little storage space yet remains accessible as a routine spare, reducing machine downtime during replacement and ensuring measuring instruments return quickly to service with minimal adjustment effort. Workshop-friendly design for dependable upkeep Designed for ease of maintenance and repeatable handling, this locking fastener accepts a standard hex key and is suited for rapid exchange during scheduled checks or ad hoc repairs. The straightforward interface minimises service time and makes inventory management more predictable, which supports operational continuity on the shop floor. For compatibility checks or fitting guidance, Metav Werkzeuge's technical advisors can confirm suitability for specific caliper models and offer practical recommendations to preserve precision and uptime. For reliable measurement retention choose the Teknik Makina M6 locking screw TC044TM — contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 for ordering and technical advice Technical data Article number: TC044TM Manufacturer: Teknik Makina SKU: TC044TM Allen key size: 3 mm Facts Weight: 0.1 kg Diameter: 11 mm Thread: M6 Total length: 27 mm Special features Product: Locking screw (Verriegelungsschraube) Operation: Allen key (hex) actuation Intended application: Precision calipers and measuring tools Brand: Teknik Makina FAQ What size Allen key is required for installation? The locking screw TC044TM requires a 3 mm Allen key for tightening and removal. Is this locking screw compatible with standard calipers? Yes, the Teknik Makina locking screw TC044TM is designed for use with precision calipers and similar measuring instruments that accept an M6 locking fastener. Which thread specification does the screw use? The component features an M6 thread, providing a secure fastening interface suitable for many workshop measuring assemblies. How compact is the part for retrofitting and spares management? With an 11 mm diameter and a total length of 27 mm, the TC044TM is compact and easy to stock as a spare, supporting rapid replacement and reduced instrument downtime. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
11mm Torx Screw M3.5, 60° Angle, 5.3mm Diameter - Teknik Makina
Take advantage of the combination of precise drive engagement and predictable seating provided by the Torx screw TC068TM; its Torx T15 drive and M3.5 thread ensure secure fastening and consistent assembly results. Order the fastener directly via Metav Werkzeuge or consult the Metav advisors for technical clarification. Torx screw TC068TM — M3.5 × 11 mm Torx fastener by Teknik Makina The Torx screw TC068TM is a compact fastener for fine mechanical assemblies and light engineering work, designed for reliable torque transfer where controlled clamping and repeatable seating are essential. Torx T15 drive for secure engagement M3.5 thread for fine assemblies 11 mm length with 5.3 mm diameter 60° head angle for reliable seating Reliable torque transfer for precise assemblies The Torx T15 star profile delivers controlled torque transmission and minimises cam‑out risk, which helps maintain screw integrity and reduces the need for rework. Combined with the M3.5 thread and a nominal 11 mm length, this fastener provides predictable clamp force in small assemblies. The specified 5.3 mm diameter and 60° head angle support consistent seating in pre‑prepared holes or countersunk features, making the component suitable for repeatable production tasks where accuracy matters. Compatibility that keeps production moving Designed to operate with standard Torx tooling, the fastener supports efficient manual or semi‑automated fitting processes. The standardised drive and metric thread simplify tool selection and inventory management, reducing downtime between operations. With a listed unit weight of 0.1 kg, handling and storage planning can be integrated into workshop logistics. The dimensional clarity of this component aids quality assurance checks and helps maintain throughput in small‑part assembly lines. Procurement clarity and documentation for workshop use Clear identification by SKU and measurable specifications streamlines procurement and traceability: the item can be referenced directly in bills of materials and maintenance records. The compact geometry and defined head angle make it easy to specify for engineers and buyers when updating assembly drawings or ordering replacement parts. For organisations seeking reliable repeatability from a recognised supplier, this fastener fits standard workshop and light industrial requirements and is accompanied by the technical data needed for process documentation. Secure consistent assembly results with Teknik Makina fasteners — order TC068TM through Metav Werkzeuge for dependable supply and further specification support from Metav Werkzeuge in Emmerich (info@metav-werkzeuge.com, +49 2822 7131930) Technical Data SKU: TC068TM Product name: Torx screw TC068TM Manufacturer: Teknik Makina eClass: 21189290 Facts Thread: M3.5 Overall length: 11 mm Diameter: 5.3 mm Head angle: 60° Weight: 0.1 kg Special features Torx T15 drive compatibility Fine thread for small assemblies Compact 11 mm length Suitable for precision workshop use FAQ What torque tools are compatible with this fastener? The Torx screw TC068TM is compatible with standard Torx T15 drivers and bits designed for small assembly operations. Is the thread size standard metric? Yes, the fastener features an M3.5 metric thread suitable for fine threaded applications. Which applications are typical for this type of screw? This type of fastener is commonly used in light engineering, instrument assemblies and other small‑part mechanical joins where controlled clamping is required. How is the component identified when ordering? Order by SKU TC068TM and specify the Torx screw TC068TM with M3.5 × 11 mm dimensions for unambiguous procurement. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
11mm Torx Screw T15 Drive M4 Thread 7mm Diameter - Teknik Makina
Secure assemblies benefit from the combination of a Torx T15 drive and an M4 thread, together with a compact 11 mm overall length for space-conscious installations. For seamless procurement or specification advice, order via Metav Werkzeuge or consult our product specialists. Torx screw — M4 thread, Torx T15 drive (Teknik Makina) Torx screw engineered for reliable fastening in workshop and industrial applications, featuring an M4 metric thread and a Torx T15 drive for consistent torque transfer M4 metric thread for standard fittings 11 mm overall length for compact assemblies Torx T15 drive for secure torque transfer 7 mm head diameter for firm seating Consistent torque and reduced cam‑out for reliable joints The fastener is built around a Torx T15 drive to ensure controlled torque application and to reduce cam‑out compared with slotted or Phillips heads. This geometry transfers force more efficiently to the screw shank, lowering the risk of driver slippage and damage to mating components. The M4 thread offers compatibility with common metric inserts and tapped holes, enabling repeatable clamping forces in production or maintenance tasks while preserving thread integrity over multiple service cycles. Compact dimensions for tight assemblies and neat finishes With an 11 mm overall length and a 7 mm head diameter, this screw suits confined spaces where a secure connection must not intrude on surrounding components. The specified 60° angle contributes to predictable seating behaviour and consistent contact with mating surfaces, which helps maintain alignment in assemblies with shallow countersinks. The compact form factor supports neat, professional finishes in panels, enclosures and small assemblies without sacrificing holding strength. Workshop compatibility and supply stability for production use Designed for efficient workshop workflows, the screw accepts a Torx key T15 as the drive tool and integrates easily into assembly processes that favour Torx interfaces. The part is produced by Teknik Makina and listed under SKU TC075TM, making it straightforward to specify on procurement documents. Sourcing via an established distributor avoids supply interruptions: pairing robust component design with dependable logistics supports uninterrupted production and reduces rework risk. For tailored advice on integrating the Teknik Makina Torx screw TC075TM into production or maintenance routines, contact Metav Werkzeuge in Emmerich—technical specialists are available by email or phone to support specification and delivery. Technical data Article number: TC075TM Manufacturer: Teknik Makina EClass: 21189290 Drive type: Torx T15 Facts Weight: 0.1 kg Diameter: 7 mm Thread: M4 Length: 11 mm Head angle: 60° Special features Drive tool: Torx key T15 Compact head for tight spaces Metric thread for standard fittings Manufacturer SKU: TC075TM FAQ What drive tool is required for this screw? The Torx screw uses a Torx T15 drive; the supplied specification for TC075TM calls for a T15 Torx key for torque application. What are the thread and length specifications? This fastener is supplied with an M4 metric thread and an overall length of 11 mm; head diameter is 7 mm with a 60° head angle. Is this component suitable for compact assemblies? Yes, the combination of an 11 mm overall length and a 7 mm head diameter makes this screw suitable for confined spaces and shallow countersinks. Who manufactures this screw and how is it identified? The screw is manufactured by Teknik Makina and is identified as TC075TM in technical documentation. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
12mm Locking Screw M5, Allen Key Compatible - Teknik Makina
Take advantage of the M5 thread and 12 mm overall length for secure, space‑saving fastening — order the locking screw directly via Metav Werkzeuge or ask our consultants for matching parts and supply. Locking screw TH512TM — M5 thread, 12 mm overall length by Teknik Cutting Tools A compact locking screw for secure fixation in tight assemblies, compatible with measuring instruments and adjustable with a 2 mm Allen key Compact M5 thread for tight assemblies 12 mm overall length for space-saving fixation Compatible with 2 mm Allen key for simple adjustment Lightweight 0.1 kg for easy handling Secure, compact fastening where space matters The M5 thread combined with a 12 mm overall length gives a compact yet secure solution for applications where clearance is limited. As a small locking fastener, it provides consistent clamping without protruding components, helping to maintain neat assembly geometry and minimise interference with moving parts. The restrained form factor makes this component suitable for instrument housings, small fixtures and measurement devices where precision and repeatability are required. Effortless installation and precise adjustment Designed for quick adjustment using an Allen key 2 mm, the fastener permits reliable tightening and re‑adjustment without specialised tools. The simple interface reduces assembly time and helps maintain consistent torque application across multiple units, which supports efficient production workflows and straightforward in‑service maintenance. For workshop environments that prioritise speed and accuracy, this locking element streamlines small‑part handling and reduces the risk of improper fastening. Integration, handling and supply reliability With a nominal weight of 0.1 kg, the component is easy to handle during assembly and stocking. Supplied by a recognised manufacturer, the item fits into established parts management systems and supports predictable stock rotation. Choosing a compact, standard‑thread locking screw like this helps to keep spare‑part lists short and procurement transparent, contributing to lower downtime and dependable workshop operation when replacements are required. Choose the Teknik Cutting Tools M5 locking screw TH512TM for compact, reliable fastening — contact Metav Werkzeuge in Emmerich for tailored advice and dependable supply. Technical Data SKU: TH512TM Product: Locking screw Manufacturer: Teknik Makina Facts Thread: M5 Overall length: 12 mm Weight: 0.1 kg Special features Compatible with measuring calipers and small fixtures Space‑saving, compact design Adjustable with 2 mm Allen key FAQ Which Allen key size is required for adjustment? The locking screw TH512TM is adjusted with a 2 mm Allen key for installation and re‑tensioning. What are the thread and length specifications? The fastener features an M5 thread and a 12 mm overall length as standard for compact applications. Is this component suitable for measuring calipers and similar instruments? Yes, the TH512TM locking screw is compatible with measuring calipers and small measurement fixtures where compact locking elements are needed. How is the screw installed and re‑adjusted? Installation and adjustment are performed with a 2 mm Allen key; the design supports quick tightening and straightforward re‑setting of the clamp position. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
12mm M5 Screw for End Mill, Hex Key T20 Compatible - Teknik Makina
Take advantage of a secure M5 thread, compact 12 mm overall length and a hex key T20 drive for reliable end‑mill clamping; order the part directly via Metav Werkzeuge or contact our consultants for application advice. Screw TC176TM – Screw for End Mill with M5 thread and T20 drive (Teknik Makina) The Screw TC176TM is a precision clamping screw for end‑mill holders, designed for reliable fixation in compact tool assemblies and suited to workshop and light industrial applications. M5 thread for secure clamping 7.3 mm core diameter for stability 12 mm overall length for compact setups Hex key T20 drive for standard toolholders Consistent clamping from accurate thread geometry The compact clamping element delivers dependable axial force through a precisely cut M5 thread, ensuring stable retention in end‑mill assemblies. The thread form has been selected for repeatable torque transmission, reducing the risk of loosening under lateral loads. Thanks to the 7.3 mm core diameter, the component balances shear strength with minimal bulk, making it suitable for confined toolholder spaces where maintaining rigidity without excess mass matters. This technical specification supports uninterrupted machining cycles and predictable tool life. Fits tight toolholder layouts without compromise With an overall length of 12 mm, this fastening solution is engineered for constrained applications where every millimetre of length counts. The low profile reduces interference with adjacent tooling and simplifies retrofit into existing holders. The hex key T20 drive provides a conventional interface for workshop torque tools and enables controlled tightening with standard torque wrenches or drivers. For operators working across varied fixtures, the combination of compact size and a standard drive type supports fast, repeatable assembly and efficient changeover. Simple integration and inspection for safe operation Assembly and inspection are straightforward: the clamping screw accepts a standard hex key and requires no special tooling, making routine checks part of normal maintenance rounds. Because the geometry is conventional and documented, torque recommendations can be applied consistently across toolrooms, supporting quality assurance protocols. The modest weight (0.10 kg) and uncomplicated design minimise handling time while helping to maintain inventory parity across similar fastenings in the workshop. For secure end‑mill clamping choose the Teknik Makina TC176TM screw and order via Metav Werkzeuge — contact Metav Werkzeuge in Emmerich for product guidance at +49 2822 7131930 or info@metav-werkzeuge.com Technical Data Article number: TC176TM Manufacturer: Teknik Makina ECLASS: 21189290 Facts Diameter: 7.3 mm Thread: M5 Overall length: 12 mm Weight: 0.10 kg Special features For end mill clamping Hex key T20 fitting FAQ What is the thread size of the screw? The thread is M5, specified for the TC176TM screw from Teknik Makina to provide reliable clamping force. Which drive tool is required for installation? Installation requires a hex key T20, matching the drive recess on the Teknik Makina TC176TM clamping screw. Is the component suitable for compact toolholders? Yes, the 12 mm overall length and 7.3 mm core diameter make the TC176TM suitable for compact end‑mill holders where space is limited. How much does the screw weigh? The screw has a listed weight of 0.10 kg, which supports easy handling and stock management. Can the screw be used across different end‑mill brands? The screw is intended for standard end‑mill clamping arrangements and, provided the toolholder accepts an M5‑threaded clamping element with a T20 drive, the Teknik Makina TC176TM is compatible Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
12mm Torx Screw M5 Thread 7mm Diameter 60° Angle - Teknik Makina
Take advantage of precise M5 threading and a compact 12 mm length for secure, space-saving fastening; the Torx drive reduces cam‑out and speeds assembly. Order directly via Metav Werkzeuge or consult our product specialists for application advice. Torx screw TC083TM — M5 x 12 mm, Torx drive (Teknik Makina) Torx screw TC083TM for mechanical assemblies where compact form and reliable torque transfer are required M5 thread for standard metric assemblies Head diameter 7 mm for defined seatings Compact 12 mm overall length for confined spaces Torx drive compatible with T20 bits Consistent M5 thread for secure connections The fastener is engineered with a defined M5 thread that provides consistent engagement and predictable clamping behaviour. Where repeatability matters, the metric thread profile reduces the risk of loosening under light vibration and simplifies torque setting during assembly. The specification supports common production and maintenance environments, enabling standardised tooling and fewer inventory variants. Space-saving dimensions that simplify assembly With an overall length of 12 mm and a head diameter of 7 mm, this component is designed for installations where clearance is limited. The compact geometry allows secure fastening without protruding components, which benefits stacked or nested assemblies. Small form factor screws like this shorten installation time in cluttered assemblies and often remove the need for additional countermeasures such as washers or spacers. Torx drive for efficient torque transfer and less wear A Torx drive provides improved engagement between tool and fastener, allowing higher torque transmission with reduced cam‑out compared with slotted or Phillips drives. The drive compatibility with T20 bits enables rapid screwdriving with cordless or pneumatic drivers while protecting both the bit and the screw head from premature damage. The result is faster cycle times and lower tool‑replacement costs in production and workshop settings. Designed for straightforward procurement and workshop use Supplied under the Teknik Makina designation, the TC083TM is a practical choice for procurement managers seeking an economical, repeatable fastening solution. The concise specification and common drive type simplify stockkeeping and tool selection. For workshops, the screw’s straightforward geometry and compatibility with standard Torx tooling support quick decisions on repair and retrofit operations. For reliable fastening from Teknik Makina, contact Metav Werkzeuge to discuss compatibility, availability or to place an order for the TC083TM fastener — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: TC083TM EClass: 21189290 Manufacturer: Teknik Makina Key measurements Diameter: 7 mm Thread: M5 Overall length: 12 mm Angle: 60° Weight: 0.1 kg Features and compatibility Drive type: Torx Compatible driver: T20 Torx key Fastener type: screw FAQ What driver is required for this screw? The screw is designed for a Torx drive and is compatible with a T20 Torx key or bit; this ensures efficient torque transfer for the TC083TM. Is the TC083TM suitable for tight assemblies? Yes, the overall length of 12 mm and a head diameter of 7 mm make the TC083TM appropriate for compact or recessed fastening applications. Which thread does this fastener use? The fastener uses a metric M5 thread, suitable for common metric assemblies and compatible with standard M5 threaded holes and inserts. Can this screw be used with power drivers? The Torx drive and T20 compatibility allow use with cordless and pneumatic drivers; correct torque settings should be observed to avoid over‑tightening. Who manufactures this screw? The screw is supplied under Teknik Makina and listed with article number TC083TM for procurement and stock purposes. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
12mm Torx Screw M5, 75° Angle, Fits T20 Key - Teknik Makina
Take advantage of the combination of standardised metric specification, compact dimensions and straightforward drive compatibility for efficient assembly and tidy stock management; order via Metav Werkzeuge or consult the team for specification advice. Torx screw TC085TM — M5 thread, 12 mm length, Teknik Makina A Torx screw TC085TM designed for secure metric assemblies where a compact length and a Torx drive ensure repeatable fastening in workshop and industrial environments M5 metric thread 6.6 mm head diameter 12 mm overall length Compatible with T20 Torx key Reliable fastening for routine assembly work The compact fastener offers a M5 thread combined with an overall length of 12 mm, delivering a standardised connection suitable for a wide range of metric assemblies. The measured 6.6 mm head diameter provides a clear reference for clearance and countersink planning, while the listed 75° head angle clarifies seating geometry for through‑holes or tapered seats. As a standard Torx fastener, the component supports consistent torque transfer and reduced cam‑out compared with slotted or Phillips drives, which helps maintain assembly quality and reduces rework in serial production. Practical compatibility and workshop use Specified for use with a T20 Torx key, the part fits common workshop tool sets and maintenance kits, enabling quick interventions without special tooling. The screw’s classification under the provided eClass identifier supports procurement and inventory systems that rely on standard taxonomy for ordering and SKU management. The compact mass of 0.1 kg per listed unit makes it easy to calculate shipping and storage requirements for small batches, and the metric thread ensures interchangeability with typical M5 threaded components used in fixtures, panels and light mechanical assemblies. Procurement advantages and inventory simplification Selecting metric fasteners with clear dimensional data reduces ordering errors and simplifies stockkeeping; the standard M5 specification and Torx drive reduce the number of different items required. For purchasing departments and maintenance planners, the combination of a defined head diameter, length and drive type supports accurate BOM entries and faster supply‑chain turnaround. The product’s SKU (TC085TM) and manufacturer details are provided for traceability and to support quality assurance processes within production and service environments. For reliable supply of Teknik Makina fasteners such as the Torx screw TC085TM, contact Metav Werkzeuge in Emmerich for product availability and procurement support — eMail: info@metav-werkzeuge.com • Phone: +49 2822 7131930 Technical data Article number: TC085TM Manufacturer: Teknik Makina ECLASS: 21189290 Facts Thread: M5 Diameter: 6.6 mm Overall length: 12 mm Angle: 75° Weight: 0.1 kg Special features Drive type: Torx Suitable for key: T20 Fastener type: Screw FAQ What are the main dimensions of this fastener? The Torx screw TC085TM has an M5 thread, a head diameter of 6.6 mm and an overall length of 12 mm as specified by the manufacturer Teknik Makina. Which tool is required for installation? Installation uses a T20 Torx key; the Torx drive on the TC085TM ensures secure torque transmission during assembly. Is this screw suitable for general workshop assemblies? Yes, the metric M5 thread and compact 12 mm length make this fastener suitable for standard workshop and maintenance applications where a Torx drive is preferred. How is the product identified for ordering and stock control? Order and inventory references use the SKU TC085TM and the eClass code 21189290 to ensure correct procurement and traceability. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
13.4mm Locking Screw M6, Allen Key 2.5 Compatible - Teknik Makina
Take advantage of secure, repeatable clamping with a compact M6 thread and a short total length for minimal interference; order the component directly via Metav Werkzeuge or consult our specialists for compatibility advice. Locking screw TH613TM — M6 thread, 13.4 mm total length (Teknik Makina) A locking screw engineered for precision calipers and other measuring instruments, designed for reliable clamping and simple adjustment with a 2.5 mm Allen key M6 threaded connection Compact 13.4 mm total length Compatible with 2.5 mm Allen key Secure clamping for repeatable measurements The compact design centres on a M6 thread that delivers consistent axial force without adding bulk to the measuring setup. By fixing the sliding scale reliably, the component improves repeatability and reduces position drift during routine checks. This contributes to fewer re-measurements and clearer traceability in quality control protocols, turning a small mechanical part into a measurable benefit for production reliability. Straightforward adjustment and low-maintenance handling Adjustment is simplified by the 2.5 mm Allen key compatibility: installation and removal are quick, safe and require only standard workshop tooling. The 13.4 mm total length limits overhang and avoids interference with jaws or depth rods, while the lightweight construction keeps added mass to a minimum. Together, these features shorten maintenance intervals and make replacements faster, supporting efficient machine uptime and operator convenience. Suited to precision calipers and compact instruments Designed for use on precision calipers, the component integrates neatly into measuring assemblies where space and accuracy matter. The small footprint and locking capability help secure settings during transport or frequent handling, which is particularly useful in busy inspection bays and mobile measurement tasks. The part’s compatibility with common Allen keys ensures broad applicability across various dial and digital caliper models. Practical impact on workflow and measurement quality As a simple upgrade to an existing measuring instrument, the locking screw contributes directly to process stability: fewer slips, fewer resets and clearer pass/fail decisions. The result is an operational uplift that is both pragmatic and measurable — less downtime, quicker inspections and a lower risk of accidental zero shifts. For workshops aiming to streamline inspection steps, this component is a compact but effective choice. For secure and compatible components, contact Metav Werkzeuge to request the Teknik Cutting Tools locking screw (TH613TM) and receive tailored advice and supply from our Emmerich centre — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data Article number: TH613TM Name: Locking screw (Verriegelungsschraube) Manufacturer: Teknik Makina Core data Thread: M6 Total length: 13.4 mm Weight: 0.1 kg Special features Compatible with 2.5 mm Allen key for adjustment Intended for use on precision calipers Simple locking function for secure measurements FAQ What thread size does the locking screw use? The locking screw uses an M6 thread for secure fastening and standard compatibility. Which tool is required for adjustment? Adjustment requires a 2.5 mm Allen key, as stated for the component. Is this component suitable for calipers? Yes. The TH613TM locking screw is intended for precision calipers and similar measuring instruments. What are the dimensions and weight of the part? Total length is 13.4 mm and the weight is 0.1 kg for the TH613TM locking screw. Can the screw be used on other measuring tools with M6 fittings? It can be used wherever an M6 locking screw with a compact profile and 2.5 mm Allen adjustment is appropriate, though it was designed with calipers in mind. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
13.6mm Locking Screw M8 x 29mm, Allen Key 5 Compatible - Teknik Makina
Take advantage of a compact fastening solution with a metric M8 thread, a 13.6 mm head diameter and a 29 mm overall length that ensure stable clamping on measuring instruments; order the locking screw directly via Metav Werkzeuge or ask our consultants if needed Locking screw — M8 thread, compatible with precision calipers A compact locking screw designed for secure clamping in measuring and workshop applications, offering reliable engagement with a 5 mm hex key Metric M8 thread for secure fastening 29 mm overall length for compact fit 13.6 mm head diameter for reliable grip Compatible with 5 mm Allen key Precise clamping that protects measurement integrity The M8 thread and compact profile deliver consistent clamping force where repeatability matters. Fitted to precision calipers and similar instruments, this fastener reduces axial play and helps maintain measurement accuracy over repeated use. The combination of a defined thread size and a measured 13.6 mm head diameter gives a controlled contact area, which prevents slippage while avoiding damage to delicate surfaces. Engineers and technicians benefit from a straightforward mechanical solution that supports quality control processes and reduces rework. Fast, uncomplicated installation for workshop efficiency Assembly requires only a 5 mm Allen key, making the fitting process quick and tool‑neutral in most workshop settings. The 29 mm overall length is optimised for compact instrument housings and avoids protrusion that could snag or impede handling. Because the design focuses on compatibility rather than complexity, downtime for replacement is kept to a minimum and routine adjustments become more efficient. The straightforward geometry also facilitates inspection and ensures that maintenance tasks remain predictable and fast. Built for dependable service in production and repair Supplied as SKU TC047TM, this locking element supports consistent performance in serial assembly and repair scenarios. When uniform fastening is a prerequisite for repeatable measurements, this component delivers the mechanical stability required in industrial metrology and workshop environments. The robust specification of the thread and head dimensions simplifies parts management and helps standardise spare-part inventories across toolrooms, inspection benches and service departments. To secure stable clamping for measurement tools, request supply or technical advice for the Teknik Cutting Tools locking screw TC047TM from Metav Werkzeuge — contact info@metav-werkzeuge.com or call +49 2822 7131930 to discuss compatibility and immediate availability Technical data Article number: TC047TM Manufacturer SKU: TC047TM Facts Diameter (head): 13.6 mm Thread: M8 Overall length: 29 mm Weight: 0.1 kg eClass: 21189290 Special features Compatible with 5 mm Allen key Suitable for precision calipers and measuring instruments Compact design for limited‑space applications FAQ What is the standard thread size of this locking screw? The locking screw features a metric M8 thread, making it suitable for standard M8 threaded fittings in measuring devices. Which tool is required for installation? Installation and removal are performed with a 5 mm Allen key, designed for quick and secure fastening. Will the head size affect access on small calipers? The 13.6 mm head diameter balances grip and compactness to reduce interference in tight instrument housings. How is the product identified for ordering or replacement? Order or reference the part by SKU TC047TM when requesting supply or technical details. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
13mm Screw for End Mill M8, 25mm Length - Teknik Makina
Take advantage of the combination of precise dimensions and secure clamping to maintain consistent milling results; the M8 thread and 13 mm nominal diameter deliver predictable seating and reliable torque transfer. Order the part directly via Metav Werkzeuge or consult the technical team for fitment details and supply options. Screw TC184TM — M8 thread, 13 mm diameter (Teknik Makina) A robust Screw TC184TM designed for fastening end mills in cutter holders, providing repeatable seating and compatibility with a 4 mm Allen key. M8 thread for secure clamping 13 mm nominal diameter Compatible with 4 mm Allen key Consistent clamping for stable machining The screw’s M8 thread is engineered to provide even clamping force across the tool holder, which supports stable cutting performance and reduces the risk of tool movement under load. In production environments where repeatability matters, a secure threaded connection minimises micro-movement that can lead to premature wear or inconsistent surface finish. The design concentrates on mechanical reliability rather than decorative elements, delivering a straightforward, functional connection that integrates with standard milling setups. Predictable dimensions for accurate setup Defined measurements such as the 13 mm nominal diameter and 25 mm total length enable predictable assembly and straightforward machine setup. These dimensions support precise alignment of the cutting tool within the holder, so runout can be kept to a minimum and concentricity maintained. Compatibility with standard clamping tools is confirmed by the requirement for a 4 mm Allen key, which simplifies tightening procedures and reduces setup time. The clear specification of size assists process engineers and workshop planners in standardising tool stacks and spare-part inventories. Practical workshop benefits and application scope Specified as suitable for use with end mills, this fastening component supports routine tool changes and maintenance cycles within milling operations. The compact form factor and defined thread size make it appropriate for both small-batch workshops and larger production lines that require dependable fastenings. When incorporated into a tool management system, the screw contributes to predictable maintenance intervals and fewer unexpected stoppages, supporting overall equipment effectiveness and continuity of machining processes. Contact Metav Werkzeuge for technical clarification or to request delivery options for the Teknik Makina M8 fastening screw; call +49 2822 7131930 or email info@metav-werkzeuge.com for personalised assistance. Technical data Article number: TC184TM Manufacturer: Teknik Makina Facts Diameter: 13 mm Thread: M8 Total length: 25 mm Weight: 0.1 kg Special features Application: for End Mill Drive: compatible with 4 mm Allen key SKU: TC184TM FAQ What is the thread size of the screw? The screw TC184TM is supplied with an M8 threaded connection for secure clamping in cutter holders. Which drive tool is required for installation? Assembly requires a 4 mm Allen key, which is compatible with the internal drive of the Teknik Makina screw. What dimensions should be expected for planning? Key dimensions are a 13 mm nominal diameter and a total length of 25 mm, as stated for the TC184TM. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
13mm Toggle Clamp 4.5mm Diameter, Zinc Plated - Teknik Makina
Compact dimensions and a precise Ø 4.5 mm interface support reliable mechanical linkage in confined assemblies; with an overall length of 13 mm and a lightweight construction of 0.1 kg, the part is optimised for responsive actuation — order the component via Metav Werkzeuge or consult their specialists for integration advice. Knee lever TL4TM – compact actuation lever, Ø 4.5 mm, 13 mm length by Teknik Makina A compact knee lever engineered for precise actuation and small-scale mechanical linkages in workshop and industrial fixtures. Compact design, 13 mm overall length Precise Ø 4.5 mm shaft interface Lightweight, approx. 0.1 kg Precise function where space is limited The knee lever delivers a compact solution for applications that demand a small footprint without sacrificing control. Its Ø 4.5 mm interface provides a defined connection point for shafts or pins, enabling consistent mechanical engagement in clamping or indexing linkages. The short overall length of 13 mm reduces lever arm overhang, which is beneficial in confined fixtures and where multiple components are mounted in close proximity. This section concentrates on measurable advantages so that planning and CAD integration can proceed from verified dimensions. Reduced inertia and straightforward integration With a mass of 0.1 kg, the lever contributes minimal inertia to moving assemblies, improving response time in frequently actuated mechanisms. The compact geometry eases incorporation into jigs, fixtures and small machines where dynamic balance matters. The functional benefit is a quieter, more efficient actuation cycle and lower wear on connected pivots. Technical teams will appreciate that the core measurable characteristics directly inform cycle-speed calculations and bearing selection for long-term reliability. Sourcing confidence and practical application advice Supplied by Teknik Cutting Tools (Teknik Makina), the component is suitable for workshop and light industrial use where small actuating elements are required. The product’s straightforward specification makes selection transparent and reduces uncertainty in procurement. Metav Werkzeuge acts as a quality filter for the European market, offering stocked supply from Emmerich and the logistical reliability expected by production planners and maintenance teams. For precise system matching, refer to the dimensional data and planning drawings before final assembly. For specification checks or to confirm suitability for a particular fixture, request the TL4TM knee lever from Metav Werkzeuge or speak to their technical advisors for part availability and delivery from Emmerich. Technical data Article number: TL4TM ECLASS: 21189290 Manufacturer: Teknik Makina Core data Diameter: 4.5 mm Overall length: 13 mm Weight: 0.1 kg Special features Product type: Knee lever Compact form factor SKU: TL4TM FAQ What are the exact external dimensions of this lever? The knee lever TL4TM has a diameter of 4.5 mm and an overall length of 13 mm as stated in the technical data. Is the lever suitable for fast actuation cycles? The lever’s lightweight construction (0.1 kg) and compact geometry make it appropriate for applications with frequent actuation, subject to system-level dynamic calculations. Can this lever be used in tight assemblies with limited overhang? Yes, the short overall length and small interface diameter are intended for installations where space is restricted. Which manufacturer supplies this component? This part is supplied by Teknik Cutting Tools (Teknik Makina), referenced under article number TL4TM. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.6mm Knee Lever, Diameter 5mm, 0.1kg - Teknik Makina
Compact, precise and lightweight: the knee lever features a Ø 5 mm pivot and an overall length of 15.6 mm, delivering secure actuation in confined assemblies while weighing just 0.1 kg. Benefit from dependable component supply and technical advice — order the part directly via Metav Werkzeuge or consult our specialists for application guidance. Knee Lever (Kniehebel) — compact actuation lever, Teknik Makina Kniehebel is a compact mechanical lever for precise actuation and clamping in tight industrial assemblies Compact knee lever design Ø 5 mm pivot for standard mounting Overall length 15.6 mm for confined spaces Lightweight construction at 0.1 kg Precision where space is limited The compact lever is engineered to deliver repeatable actuation in tight assemblies. With a Ø 5 mm pivot and an overall length of 15.6 mm, the unit is suited to installations where clearance is restricted and reliable mechanical movement is essential. The small mass — 0.1 kg — reduces inertia during operation, which helps improve cycle times in repetitive tasks. These measurable characteristics simplify planning for retrofit work and small-machine builds. Designed for efficient assembly and dependable operation A simple, robust mechanical design reduces complexity at the point of use and supports straightforward installation. The compact actuation lever provides consistent mechanical advantage without electrical components, meaning fewer failure modes and predictable behaviour under normal operating conditions. This focus on functional reliability supports uninterrupted workflows in production and maintenance contexts, offering a clear efficiency gain for workshop and industrial environments. Integration and mounting explained The lever’s defining dimensions — a Ø 5 mm pivot and a 15.6 mm overall length — make mounting and alignment predictable when integrating into existing mechanisms. In mechanical terms, a knee lever converts small input movement into controlled clamping or release; the compact geometry here is beneficial where a short throw and compact footprint are required. For planners and fitters, the clear dimensional data allows accurate hole and shaft preparation, reducing trial fitting and saving assembly time. For supply, compatibility advice or batch enquiries for the Teknik Makina knee lever, contact Metav Werkzeuge in Emmerich — call +49 2822 7131930 or email info@metav-werkzeuge.com for tailored recommendations and reliable delivery. Technical data SKU: TL4BTM Manufacturer: Teknik Makina ECLASS: 21189290 Weight: 0.1 kg Diameter: 5 mm Overall length: 15.6 mm Article name: Kniehebel (knee lever) UID: TL4BTM FAQ What are the key dimensions of this knee lever? The knee lever from Teknik Makina (SKU TL4BTM) is listed with a diameter of 5 mm and an overall length of 15.6 mm, with a weight of 0.1 kg. What material is the component made from? Material information for the Teknik Makina knee lever TL4BTM is not specified in the provided technical data. Is load capacity or duty rating stated for the part? No rated load or duty class is provided in the available data for the TL4BTM knee lever. How is the lever mounted? The component indicates a 5 mm pivot diameter, which corresponds to a 5 mm mounting pin or shaft for mechanical attachment. Can this lever be used as a direct replacement in machines? Compatibility depends on the machine’s mounting geometry and functional requirements; check the listed dimensions (Ø 5 mm, 15.6 mm length) against the original part Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Clamp Prong Adjustable For WNMG 06 - Teknik Makina
Take advantage of a compact, purpose-built clamping wedge that secures WNMG 06 turning inserts with reliable repeatability and low added mass; combine precision, simple integration and trusted supply from Metav Werkzeuge for uninterrupted workshop operation — order directly via Metav Werkzeuge or consult the team for application advice. Spannpratze — clamping wedge for WNMG 06 inserts by Teknik Makina A Spannpratze engineered as a compact clamping wedge to secure WNMG 06 turning inserts in compatible turning toolholders for workshop and light industrial use Clamping wedge for WNMG 06 inserts Lightweight: approx. 0.1 kg Designed for turning toolholders Consistent clamping for reliable turning performance The clamping wedge provides a straightforward mechanical solution for securing indexable inserts, delivering secure clamping and repeatable positioning that support consistent cutting performance. By focusing on a simple wedge principle, the component offers a predictable clamping force that helps maintain insert alignment during turning operations. The design reduces variables in the tool assembly and supports process stability, which is particularly valuable in production runs where reproducible results matter. Compatibility with WNMG 06 geometry ensures the device interfaces with a widely used insert form, easing part selection and spare‑part management. Compact design that simplifies workshop workflows A compact component with a lightweight profile, the wedge is intended for easy handling and rapid replacement at the bench. Reduced mass contributes to simpler tool balancing and minimises the impact on the holder assembly, while the compact footprint aids installation in confined toolholder envelopes. For workshop teams, this translates into quicker change‑overs and fewer interruptions. Clear physical form and standard mounting dimensions make inventory and storage straightforward, supporting efficient stock rotation and rapid availability of spares for routine maintenance. Robust integration and practical benefits for procurement Specified by a recognised manufacturer, the component is suited to standard turning setups requiring WNMG 06 inserts and fosters interoperability across common toolholder systems. Selecting such a dedicated clamping element helps streamline procurement and reduces the need for custom solutions, thereby shortening lead times and simplifying supplier lists. The practical nature of the part lends itself to predictable service life when used within normal operating parameters, contributing to dependable workshop throughput and lower administrative effort in parts management. Contact Metav Werkzeuge to check compatibility with existing holders and secure Teknik Makina clamping wedges for WNMG 06 applications — assistance and order processing available from Metav Werkzeuge in Emmerich by phone or email. Technical Information Article number: BK019TM Manufacturer: Teknik Makina Core data Weight: 0.1 kg eClass: 21189290 Design & compatibility Suitable for WNMG 06 inserts Product name: Spannpratze UID: BK019TM FAQ What is this component used for? The Spannpratze by Teknik Makina is used as a clamping wedge to secure WNMG 06 turning inserts in compatible toolholders, ensuring repeatable positioning during turning operations. Is the clamping wedge suitable for all WNMG 06 toolholders? Compatibility depends on the toolholder design; the Spannpratze is designed for standard WNMG 06 insert geometries, but verification against the specific holder dimensions is recommended before installation. How much does the component weigh and why does that matter? The clamping wedge weighs approximately 0.1 kg; the lightweight design reduces added mass to the tool assembly, which aids handling and minimises changes to holder balance. Are any special maintenance steps required? Routine inspection for wear, cleanliness of the clamping surfaces and correct torqueing of fastening elements will help maintain clamping reliability; replace the wedge if deformation or surface damage is detected. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com