Improve machine uptime with precision runout testers
Runout testers ensure precise measurement of concentricity and runout on rotating parts, reducing setup and downtime by up to 80% while supporting outside, inside and face measurements for shafts, bushes, gears and bearings. Metav runout testers with tailstocks deliver fast, flexible setups that allow operators to carry out a runout check in as little as 10 seconds and determine coaxiality, runout accuracy and face runout directly at the machine. These devices are ideal for assessing components used in engines and drivetrains, such as camshafts, crankshafts and drive shafts, and help prevent scrap and rework by identifying form and alignment deviations early.
1000mm Runout Testing Device 170mm Measuring Height, 16mm Movable Tip Travel, Cast Frame, 85kg - Metav IndustryLine
Benefit from a high-capacity metrology station that combines a 1,000 mm measurement range with ±0.02 mm repeatability and a rigid cast-iron construction to keep production checks fast and reliable; order the M208.203 runout tester directly via Metav Werkzeuge or consult our specialists if further integration advice is required. M208.203 Runout tester — 1,000 mm range, 170 mm measuring height (Metav IndustryLine) M208.203 Runout tester is a heavy-duty inspection unit for concentricity and runout verification on shafts and rotors, designed for repeatable checks in workshop and small-series production environments. 1,000 mm measurement range for large components 170 mm measuring height for axial setups Cast-iron frame and centres for maximum stability 16 mm travel on movable centres Precision control for production acceptance and SPC The unit delivers consistent runout assessment thanks to a specified accuracy of ±0.02 mm, which supports reliable in-process checks and short-run quality gates. With a 1,000 mm measurement range, the station accommodates long shafts and larger assemblies that are impractical on bench instruments, reducing handling and turnaround time. The translated technical design concentrates on mechanical stability rather than electronic complexity, which simplifies routine measurements and helps maintain process capability. This rational advantage makes the station particularly suited for manufacturing operations that require traceable and reproducible concentricity results. Built for stability and low measurement uncertainty A cast-iron frame and cast centres form the structural backbone, damping vibrations and resisting thermal distortion during inspections. The 60° measuring tips and a centre height of 176 mm ensure positive contact geometry, while the movable centres provide fine positional adjustment with 16 mm travel, facilitating quick clamping of diverse workpieces. These mechanical choices reduce operator-induced variation and support tighter tolerances without elaborate fixtures, which translates into fewer reworks and more consistent parts passing final inspection. Flexible fixturing for diverse shaft and spindle geometries The arrangement of cross arm and column (Ø10 × 150 mm and Ø12 × 176 mm respectively) allows straightforward adaptation to different diameters and support points, so setup time is minimised. A 170 mm measuring height is especially useful when axial access and clearance are limited; it allows the unit to inspect parts that require off-centre supports or accessory tooling. The combination of reach and stable support means the tester can be used for individual quality checks, first-off inspections, and spot checks during production without resorting to production-line downtime. Workshop integration, traceability and practical benefits The design focuses on durable, low-maintenance operation: robust materials and simple kinematics mean fewer servicing intervals and predictable long-term performance. Identification details such as SKU and GTIN make asset tracking and procurement straightforward for procurement and calibration logs. By providing clear measurement capability and a stable fixturing platform, the device reduces the need for repeated checks elsewhere in the process, supporting a smoother workflow and greater confidence in final part quality. For tailored technical advice and supply from Metav IndustryLine, contact Metav Werkzeuge in Emmerich and quote M208.203 to discuss delivery options, spare parts and integration into existing inspection routines Technical Data Article number: M208.203 GTIN: 4054469105369 eClass: 27201190 TARIC / CN: 90173000 Facts Measurement range: 0–1,000 mm Measuring height: 170 mm Accuracy: ±0.02 mm Movable centres travel: 16 mm Centre height: 176 mm Cross arm: Ø10 × 150 mm Column: Ø12 × 176 mm Overall length: 1,420 mm Special features Frame and centres made from cast material Measuring tips: 60° geometry Designed for concentricity and runout checks Suitable for inspection of long shafts and rotors FAQ What measurement accuracy can be expected from this station? The M208.203 runout tester provides an accuracy of ±0.02 mm for runout measurements, ensuring dependable results for production control and acceptance. Which component dimensions are supported by the tester? With a measurement range of 0–1,000 mm and a measuring height of 170 mm, the device handles long shafts and larger assemblies that require a stable inspection platform. What materials make up the inspection unit? The station is constructed with a cast frame and cast centres to deliver high rigidity and reduced vibration, which improves repeatability during measurements. How are different shaft diameters accommodated? Adjustable centres with 16 mm travel and 60° measuring tip geometry enable secure contact and quick reconfiguration for differing diameters and fixture setups. Is the instrument suitable for routine production use? Yes; the combination of a wide measurement range, low measurement uncertainty and robust construction makes it well suited for routine shop‑floor inspection and short‑run quality assurance using Metav IndustryLine components. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
20-102mm Runout Tester Two-Point Measurement 0.002mm Resolution, Max Workpiece Length 203mm - Metav IndustryLine
Take advantage of 0.002 mm measurement accuracy and a 20–102 mm measuring range combined with a grooved roll and manual handwheel for reliable series inspection; order the run‑out tester directly via Metav Werkzeuge or consult our specialists for integration advice. M208.211 Run‑out tester — 0.002 mm accuracy, 20–102 mm range (Metav IndustryLine) The M208.211 is a precision run‑out tester designed for fast assessment of radial and axial run‑out on shafts and cylindrical components during series inspection in workshop and production environments 0.002 mm accuracy for fine run‑out checks Measurement range 20–102 mm Grooved roll with two cuts for reliable seating Suitable for series measurements up to 203 mm Precise run‑out control that supports production quality The instrument delivers an accuracy of 0.002 mm, making it suitable where tight run‑out tolerances are critical. By converting radial deviations into repeatable indicator deflection, the device enables objective verification of concentricity and roundness on rotating parts. The 20–102 mm measurement range covers common shaft diameters while the 0.002 mm resolution reduces the need for secondary checks, supporting faster decision‑making in quality control. Emphasis on measurable accuracy helps to reduce scrap rates and rework, which in turn improves production throughput. Built for efficient series inspection and repeatability Designed for series applications, the tester is optimised for reproducible checks across batches. The grooved roll with two cuts secures components consistently and prevents slip during rotation, while the mechanical design keeps setup time low. Where repeatability matters, the combination of solid seating and accessible adjustment reduces operator influence on results, thereby increasing the reliability of comparative runs. This focus on consistent handling supports streamlined inspection routines and integrates well into existing in‑line or off‑line metrology stations. Practical handling and workshop compatibility A compact footprint and a manual handwheel enable controlled rotation and fine positioning without complex drive systems. The unit supports workpieces up to 203 mm in length and remains portable at approximately 5 kg, allowing transfer between benches or cells. Note that the device is supplied without a dial gauge or fine measuring device, so the indicator can be chosen to match the required resolution and display format. The tester is intended for series measurements and so prioritises robust, serviceable components that perform under regular use. Contact Metav Werkzeuge for tailored advice on integrating the M208.211 run‑out tester with 0.002 mm accuracy into production and to discuss suitable indicator options Technical data SKU: M208.211 GTIN: 4054469183732 Label: Run‑out tester 20–100 mm, 0.002 mm, grooved roll Note: Delivered without dial gauge or fine measuring device Core specifications Accuracy: 0.002 mm Measurement range: 20–102 mm Max workpiece length: 203 mm Weight: 5 kg Aufnahme: 8 Special features Grooved roll with two cuts Manual handwheel Measurements at two positions simultaneously possible Suitable for series measurements FAQ What run‑out accuracy can be expected from this tester? The M208.211 provides an accuracy of 0.002 mm, suitable for fine run‑out inspections and stringent quality control tasks. Which diameters can be measured with this device? The tester covers a measurement range of 20–102 mm, accommodating a wide span of common shaft and cylindrical part diameters. Is the device supplied ready for measurement or are additional parts required? The unit is delivered without a dial gauge or fine measuring device; the M208.211 accepts industry‑standard indicators so the display and resolution can be selected to suit the application. Can this instrument be used for series inspections on a production line? Yes, the M208.211 is intended for series measurements and its grooved roll and robust mechanics support repeated, reliable checks. What seating or fixation features support repeatability? A grooved roll with two cuts provides consistent seating of the workpiece, helping to reduce slippage and improve repeatability during rotational checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
300mm Runout Tester For Diameters Up To 130mm, 16mm Travel Of Movable Tips, Cast Construction - Metav IndustryLine
Ensure consistent rotational accuracy with the combination of 0.01 mm measurement resolution, a cast-iron frame for vibration damping and a 16 mm travel of the movable centres; order the device directly via Metav Werkzeuge or consult our specialists for application advice. Runout tester M208.200 — 300 mm runout gauge for diameters up to 130 mm (Metav IndustryLine) A Runout tester M208.200 designed for precise rotational runout inspection of shafts and cylindrical components, ideal for workshop and small-series quality control. 0.01 mm resolution for precise runout checks Cast-iron frame and centres for stable measurements Movable centres travel 16 mm Suitable for diameters up to 130 mm Consistent, verifiable accuracy for quality control The core advantage is the 0.01 mm resolution, which makes the device suitable for standard workshop inspections and finer control tasks. Classified within the standard measuring range (up to 300 mm), this gauge offers a balance of reach and stiffness that fits routine machine‑shop use. In practical terms, the shown resolution allows operators to detect minute eccentricities that would otherwise pass unnoticed during manual assembly or balancing operations, supporting process decisions and reducing rework. Stable construction reduces measurement scatter Built with a cast-iron frame and centres, the apparatus delivers high intrinsic damping and resistance to thermal and mechanical influences. The substantial mass (weight 50 kg) and the defined structural geometry help to absorb vibration and keep the datum alignment stable during rotation. The result is improved reproducibility: repeated checks give consistent values, which simplifies statistical control and traceability in inspection logs and reduces uncertainty in final acceptance testing. Flexible centring and straightforward handling The device features measuring centres with a conical 60° tip and a movable-centre travel of 16 mm, enabling secure contact with a wide range of workpiece geometries without the need for complex fixtures. The cross arm (Ø10 x 150 mm) and column (Ø12 x 176 mm) dimensions provide a rigid support for the rotating part while allowing quick adjustments. For routine runout checks, the set-up time is minimised: once the component is supported between the centres, rotation and measurement can proceed immediately, which improves throughput in repetitive inspection tasks. Designed for workshop integration and reliability Engineered for daily industrial use, the gauge is optimised for rotational inspection of components up to 130 mm diameter within a 300 mm measuring envelope. The robust design and simple mechanical principle make maintenance straightforward and long-term operation economical. As part of the Metav IndustryLine range, the device benefits from a distribution and quality filter based in Emmerich, ensuring reliable availability and documentation for purchasers in Europe. Contact Metav Werkzeuge for bespoke advice on application and ordering of the Metav IndustryLine runout tester M208.200; technical consultants are available at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data Article number: M208.200 GTIN: 4054469183541 Manufacturer: Metav IndustryLine Facts Measuring range: 0–300 mm Maximum measurable diameter: up to 130 mm Accuracy / resolution: 0.01 mm Movable-centre travel: 16 mm Weight: 50 kg Overall length: 720 mm Cross arm: Ø10 x 150 mm Column: Ø12 x 176 mm Special features Cast-iron frame and centres Measuring centres 60° (height 176 mm) Suitable for rotational runout inspection Designed for workshop and small-series inspection FAQ How accurate is the runout measurement on this tester? The runout gauge offers a resolution of 0.01 mm, enabling detection of small eccentricities suitable for standard workshop quality control. What size of components can be inspected? Components with diameters up to 130 mm can be supported and checked within the device’s 300 mm measuring envelope. What advantages does the cast-iron construction provide? The cast-iron frame and centres increase damping and structural stability, improving reproducibility and reducing the influence of vibration on measurements. Does the device allow adjustment for different part geometries? Yes, the movable centres with 16 mm travel and the conical 60° measuring centres permit secure centring of a variety of cylindrical parts. Is the runout tester part of a defined product line? The device is supplied under Metav IndustryLine and is intended for reliable workshop integration and routine inspection tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
35mm Runout Tester For Shafts, 0.005mm Accuracy, 100mm Max Workpiece Length, Grooved Roller - Metav IndustryLine
Benefit from 0.005 mm runout resolution, a compact 1–35 mm measuring range and simultaneous dual-point inspection that speeds up series checks. Secure consistent radial and face runout control with a grooved support roller and fine handwheel adjustment. Order the unit directly via Metav Werkzeuge or consult our specialists for application advice. Runout testing device M208.213 — precise runout control, 1–35 mm range The Runout testing device M208.213 is a bench instrument for verifying radial and axial runout on shafts and small cylindrical components, optimised for repeatable shop‑floor inspection. 0.005 mm measurement resolution Measuring range 1–35 mm Simultaneous dual-point measurement Suitable for series measurements Precise measurement where it matters The instrument delivers an exacting 0.005 mm accuracy, making it suitable for quality checks where tight concentricity and face runout are critical. The fine resolution supports detection of minute deviations that can cause vibration, premature bearing wear or assembly misfit. As a result, production tolerances are easier to maintain and rework rates can be reduced, which contributes directly to consistent throughput and predictable part quality. The device is presented as a metrology tool for repeat inspections rather than a one-off check. Compact range with practical benefits With a 1–35 mm measuring range and a maximum workpiece length capacity of 100 mm, the tester covers small to medium shafts commonly encountered in precision assemblies. The roller with grooves secures cylindrical parts and prevents slippage while the robust construction keeps the measuring geometry stable. The comparatively light weight of 3 kg and bench footprint enable positioning on workshop measuring tables or integration with a stand for repeatable setups, combining reach and rigidity in a compact package. Faster series inspection through dual‑point measurement The design permits simultaneous dual-point readings, which halves the number of repositioning steps for many workpieces and speeds up throughput in serial testing. A manual fine‑adjustment handwheel allows controlled, tactile alignment and minimises operator-induced variability during setup. These features together create a workflow advantage: fewer handling steps, shorter cycle times and more reproducible results for batch inspection without sacrificing accuracy. Designed for workshop reliability Built for routine use, the instrument supports continuous series inspection and is adapted to the demands of a production environment. The construction emphasises repeatability and user ergonomics, reducing the chance of setup errors and enabling technicians to perform consistent runout assessments throughout a shift. Where calibration and traceability are required, regular calibration routines should be scheduled to maintain measurement certainty in line with internal quality plans. Contact Metav Werkzeuge today to discuss how the M208.213 can be integrated into existing inspection processes or to request tailored advice for specific shaft inspections Technical data Article number: M208.213 Label: Rundlaufprüfgerät 1 - 35 mm, 0,005 mm max. Werkstücklänge 100 mm, Rolle mit Nuten Manufacturer: Metav IndustryLine Key figures Measuring range: 1.0–35 mm Maximum workpiece length: 100 mm Accuracy: 0.005 mm Weight: 3 kg Aufnahme: 8 Special features Roller with two grooves (mit 2x Einschnitte) Simultaneous measurement at two positions Hand-operated fine adjustment (handwheel) Suitable for series measurements Compatible with bench mounting / use with stand FAQ What kinds of parts can be inspected with this runout tester? The runout tester is designed for shafts and small cylindrical components; the M208.213 handles parts up to 100 mm in length within the 1–35 mm diameter range. How does the dual‑point measurement help in production? Measuring at two positions at once reduces repositioning and shortens cycle time, which improves throughput during batch or series inspection. Is the instrument portable between workstations? At 3 kg and with a compact bench footprint, the unit is readily moved between measuring tables and can be mounted on appropriate stands for fixed setups. How is slippage prevented during measurement? The roller support features two grooves that stabilise cylindrical parts, ensuring repeatable seating and lower measurement scatter. Can the device be used for both radial and face runout checks? Yes; the tester is configured for radial and axial runout verification on cylindrical workpieces within its geometric limits. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
35mm Runout Tester With 0.002mm Resolution, Two-Point Measurement, Grooved Rollers, 100mm Max Workpiece Length - Metav IndustryLine
Take advantage of the combination of 0.002 mm accuracy, a compact 1–35 mm measuring range and grooved rollers for repeatable support to streamline runout inspection in production. Order the runout tester directly via Metav Werkzeuge or ask our consultants if needed. M208.210 Runout Tester — compact runout testing device with 0.002 mm accuracy by Metav IndustryLine M208.210 is a precision runout testing device designed for evaluating radial and axial runout on shafts and small cylindrical components in production and inspection environments. High resolution 0.002 mm accuracy Measuring range 1–35 mm Grooved rollers for secure support Simultaneous two-point measurement Precision and repeatability for production control The unit delivers 0.002 mm repeatability within a compact 1–35 mm measuring window, making it suitable for fine runout verification where tight tolerances matter. With this level of resolution, the device supports statistical process control and in-line quality checks by providing a stable, quantifiable measurement base; variances that would otherwise pass unnoticed can be identified quickly. The calibrated mechanical guidance and firm roller support reduce measurement scatter, so each check contributes reliable data for production decisions and corrective actions. Secure support and faster throughput in series inspections Designed to hold workpieces up to 100 mm length on grooved rollers with two slots, the instrument minimises slippage and centring errors during rotation. The roller arrangement enables simultaneous two-point measurement, which halves setup time when identifying eccentricity across multiple surfaces. A tactile hand wheel offers fine adjustment for alignment without complex fixtures, improving handling speed and keeping cycle times low for batch testing. These features together increase throughput while maintaining consistent measurement conditions for repeated inspections. Practical workshop integration and clear operational benefits The compact construction and roughly 3 kg mass make the device easy to position on a bench or a metrology table while retaining the stiffness needed for reproducible results. It suits routine checks in machine shops, quality departments and small-series manufacturing where reliable runout data is required without a large footprint. Note that the unit is supplied without a dial gauge, allowing users to pair their preferred indicator or sensor depending on the measurement chain and traceability requirements. For workshop adoption this flexibility supports existing calibration strategies and measuring equipment inventories. For precise runout verification choose the Metav IndustryLine M208.210 — contact Metav Werkzeuge for a tailored supply and technical advice. Technical data SKU: M208.210 GTIN: 4054469183725 eClass: 27201190 Numerical data Measuring range: 1.0–35 mm Maximum workpiece length: 100 mm Accuracy: 0.002 mm Weight: 3 kg Mounting positions: 8 Special features Grooved rollers with two cuts Simultaneous two-point measurement Hand-operated fine-adjustment wheel Supplied without dial gauge / fine measuring instrument Suitable for series measurements FAQ What accuracy can be expected from this runout tester? The runout tester delivers an accuracy of 0.002 mm, enabling sub-micron-sensitive evaluation for demanding runout inspections. What is the measuring range and maximum workpiece length? Measuring range is 1.0–35 mm with a maximum recommended workpiece length of 100 mm for reliable support and repeatable results. Are the rollers suited for cylindrical shafts and small components? Yes, the grooved rollers with two cuts provide secure support for shafts and small cylindrical parts, improving centring and stability during measurement. Is a dial gauge included with delivery? No, the device is supplied without a dial gauge so that the preferred indicator or electronic sensor can be fitted according to the user’s measurement chain. Can this device be used for series inspections? The design and adjustment features make it particularly suitable for series measurements, allowing efficient repetitive checks in a production environment. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
35mm Runout Tester With 0.005mm Resolution, Max 100mm Workpiece Length, Plain Roll, Two-Point Measurement - Metav IndustryLine
Take advantage of precise runout control combined with compact handling: the device delivers 0.005 mm repeatability across a 3–35 mm diameter range and accepts workpieces up to 100 mm long, enabling efficient serial inspection with reliable results — order the runout tester directly via Metav Werkzeuge or ask our consultants if needed. Runout Tester M208.212 — 0.005 mm accuracy, 3–35 mm diameter The Runout Tester M208.212 is a compact measuring instrument for assessing radial and axial runout on shafts and short components in workshop and production environments. High precision 0.005 mm runout resolution Diameter range 3–35 mm for small shafts Simultaneous two-point measurement capability Compact for workpieces up to 100 mm long High-precision control for production quality The tester provides a 0.005 mm accuracy class that supports tight quality tolerances in machining and assembly. Such resolution reduces the need for repeated rework by detecting radial deviations at an early stage, improving process yield. The numerical specification is directly relevant for production control and incoming inspection, since the instrument translates small geometric deviations into actionable information for machine settings and corrective grinding. The emphasis on measurable precision strengthens traceability and shortens decision cycles during batch release. Built for efficient measurements on short shafts With a measuring range from 3–35 mm and a permitted workpiece length up to 100 mm, the device is tailored to inspections of small-diameter shafts, pins and short couplings. The capability for simultaneous two-point measurement halves the inspection time for concentricity checks and reduces handling steps in serial workflows. A manual handwheel provides fine positioning without the need for complex fixtures, which simplifies repetitive measurements in production and quality laboratories where throughput and reproducibility are essential. Practical mechanics that protect parts and simplify handling The roller is supplied without grooves, avoiding contact marks on finished surfaces while still providing stable support for rotating parts. Built as a compact unit and weighing approximately 3 kg, the instrument is easy to position on a bench or measuring table and integrates well with existing inspection jigs. Robust mechanical design and a clear focusing on repeatable clamping and rotation ensure that measurement scatter is minimised and inspection results remain consistent from piece to piece. Contact Metav Werkzeuge today for technical advice or to arrange a specification review for the Runout Tester M208.212 Technical Data Article number: M208.212 GTIN: 4054469183756 Label: Runout tester 3–35 mm, 0.005 mm, max. workpiece length 100 mm Facts Measuring range: 3–35 mm Max. workpiece length: 100 mm Resolution / accuracy: 0.005 mm Weight: 3 kg Mounting: 8 Special features Two-point simultaneous measurement Roller without grooves Handwheel for fine adjustment Suitable for serial measurements Compact design for bench use FAQ How accurately can runout be measured with this tester? The runout tester achieves an accuracy of 0.005 mm, allowing reliable detection of small radial deviations on shafts within the specified range. What shaft diameters and lengths are supported? The instrument covers diameters from 3–35 mm and is designed for workpieces up to 100 mm long, making it suitable for short shafts and small rotating parts. Can two measurements be taken at the same time? Yes — the device supports simultaneous two-point measurement, which speeds up concentricity and runout checks during serial inspections. Will the roller damage finished surfaces? The roller is supplied without grooves, which minimises marking on the component surface while still providing secure support during rotation. Which SKU identifies this product for ordering? Order references: M208.212 (GTIN 4054469183756) for procurement and inventory management. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
3–25mm Runout Testing Device With Spring-Loaded Adjustable Contact Wheel, Aluminium - Filetta
Take advantage of high repeatability (0.002 mm) and a compact 3–25 mm measuring range combined with a spring-loaded, height-adjustable pressure roller for consistent contact during runout checks; order the device directly via Metav Werkzeuge or consult our specialists for tailored application advice. Runout tester MS910.491 — compact runout measuring device, 0.002 mm accuracy (Filetta) Runout tester MS910.491 is a compact measuring device for quickly checking radial runout on small shafts and precision components in machining and quality control environments. Compact 3–25 mm measuring range for small diameters High repeatability with 0.002 mm resolution Spring-loaded height-adjustable pressure roller for consistent contact Aluminium-alloy body for low weight and stable alignment Precision that speaks for itself The instrument delivers 0.002 mm accuracy, making it suitable where tight radial tolerances are required. The measuring range 3–25 mm targets small-diameter parts such as pin shafts, small bearings and precision spindles; this positions the unit in the micro class of runout testers, where space efficiency and stiffness are crucial. Stated accuracy is a decisive factor for quality assurance workflows: repeatable readings reduce rework and support faster go/no-go decisions on the production line. Designed for repeatable contact and straightforward setup Mechanical features are chosen for reproducibility and ease of use. The body is machined from aluminium alloy, keeping the total mass to 3.5 kg while maintaining alignment. A spring-loaded, height-adjustable pressure roller ensures uniform contact force across measurements, while the integrated handwheel aids fine positioning. The device accepts mounting or reception at Ø6 mm and Ø8 mm, and is provided with a fixing pin Ø7.56 mm for secure fixturing. Two threaded mounts (2x M8) are available for attachment to stands or fixtures, supporting stable tests and quick alignment to a reference axis. Note: delivery excludes a dial indicator and the additional accessories shown in product images. Where it fits in the workshop and what it enables This compact runout tester is suited to toolrooms, precision assembly benches and inspection departments that need a fast, reliable check of concentricity and radial deviation on small components. The device helps to identify out-of-tolerance shafts before final assembly, lowering scrap rates and speeding process control routines. The combination of low mass, compact footprint and consistent contact control makes it straightforward to integrate into bench setups or paired with a stand for repeat measurements. For procurement decisions, the Filetta MS910.491 delivers a balance of precision, handling and quick fixturing that supports efficient quality gates. For reliable runout measurement with the Filetta MS910.491, contact Metav Werkzeuge in Emmerich to arrange supply or discuss suitability for specific parts and fixtures Technical data Article number: MS910.491 Brand: Filetta Category: Messgeräte / Schaubstock | Prismen Material: Aluminium alloy Included accessory: Fixing pin Ø7.56 mm Note: Delivery without dial indicator and additional accessories shown in image Facts Measuring range: 3.0–25.0 mm Maximum accuracy: 0.002 mm Weight: 3.5 kg Mounting threads: 2x M8 Accepts Ø6 mm and Ø8 mm reception Special features Spring-loaded, height-adjustable pressure roller Handwheel for fine adjustment Compact design for micro-range components Stable aluminium-alloy construction FAQ How small a shaft can be checked with this runout tester? The runout tester MS910.491 covers a measuring range from 3.0 to 25.0 mm, so it is intended for small-diameter shafts and similar precision components. What level of precision can be expected during repetitive measurements? Repeatability is expressed as 0.002 mm, enabling consistent runout checks suitable for tight-tolerance quality control tasks with the Filetta runout tester MS910.491. Can the device be mounted to a stand for repeated checks? Yes. The unit has 2x M8 mounting threads and accepts Ø6 mm and Ø8 mm receptions, allowing secure mounting to stands or fixtures for reproducible setups. Is a dial gauge included for measurement readout? No. The delivery explicitly excludes a dial indicator and the other accessories pictured; the tester is supplied with the fixing pin Ø7.56 mm only. What benefits does the spring-loaded pressure roller provide? The spring-loaded, height-adjustable pressure roller ensures consistent contact force across the measured surface, reducing variation caused by manual pressure and improving measurement repeatability. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
500mm Runout Tester With 170mm Measuring Height, 16mm Travel Of Movable Tips, Cast Frame - Metav IndustryLine
Take advantage of the combination of high repeatability, a 0.02 mm accuracy class and a rigid cast construction for reliable runout inspection across small to medium components; order the runout tester directly via Metav Werkzeuge or ask our consultants for specification matching. Runout tester M208.201 – 500 mm measuring range, 0.02 mm accuracy (Metav IndustryLine) The Runout tester M208.201 is a bench-mounted runout inspection device for radial and rotational accuracy checks on components up to 500 mm, designed for precision workshops and metrology tables. 500 mm measuring range Accuracy 0.02 mm for precise control Cast frame and centres for dimensional stability Movable centres with 16 mm travel Consistent measurement performance for quality control The instrument delivers a defined measurement environment that reduces variation in production testing. With a guaranteed accuracy of 0.02 mm, the bench enables traceable runout checks and consistent pass/fail decisions during incoming inspection or in-process control. The 500 mm measuring range covers typical shaft and rotor lengths encountered in toolrooms and small-component manufacturing, while the measuring height of 170 mm allows clearance for standard fixtures. Operationally, the device supports repeatable radial checks by securing the component between centres and rotating it under observation, which reduces rework and speeds throughput. Stable cast construction reduces setup uncertainty A heavy, rigid chassis improves reproducibility by lowering natural vibration and thermal sensitivity. The frame and tailstock components are cast for rigidity, providing a stable reference surface that maintains alignment under load; the unit’s mass (approx. 80 kg) further dampens external disturbances. The twin centres are machined to a 60° tip angle and 176 mm tip height to suit common shaft profiles, and the movable centre travel of 16 mm allows fine axial positioning without additional fixtures. Together, these features mean fewer adjustments before measurement and a lower risk of operator-induced deviation. Practical dimensions and integration into the workshop Designed for placement on a metrology table or dedicated measuring bench, the tester’s overall length of 920 mm and compact cross‑section (cross arm Ø10×150 mm, column Ø12×176 mm) make it straightforward to integrate into existing inspection stations. The unit supports standard rotational checks and can be combined with external measuring instruments for amplitude analysis or dial indicators for visual readout. The instrument is supplied as a robust bench device suited to production and maintenance environments where repeatability and mechanical stability are priorities; documentation and traceable identifiers assist in process control and inventory handling. Choose Metav IndustryLine for stable metrology hardware—contact Metav Werkzeuge in Emmerich for technical matching and fast supply of the M208.201 runout tester Technical data SKU: M208.201 GTIN: 4054469105352 ECLASS: 27201190 Label: Runout tester 500 mm measuring height 170 mm, 80 kg Facts Measuring range: 0–500 mm Measuring height: 170 mm Nominal accuracy: 0.02 mm Weight: 80 kg Overall length: 920 mm Movable centres travel: 16 mm Cross arm: Ø10×150 mm Column: Ø12×176 mm Special features Frame and centres made from cast for stiffness Measuring centres with 60° tip angle, height 176 mm Designed for bench-mounted runout inspection Category: Messtisch / metrology table application Manufacturer brand: Metav IndustryLine FAQ What measuring range does the tester cover? The runout tester covers a measuring range of 0–500 mm and a measuring height of 170 mm, suitable for small to medium shafts and rotors. What level of accuracy can be expected? The device provides a nominal accuracy of 0.02 mm, enabling repeatable radial measurements for quality control tasks. Which features ensure measurement stability? Stability is achieved through a cast frame and centres, substantial unit mass (~80 kg) and machined centre geometry, which together reduce vibration and setup drift. Is the tester suitable for a production environment? Yes—the construction and dimensional data (920 mm length, solid mounts) make it appropriate for workshop and production metrology stations. How is the product identified for ordering and inventory? Order and identify the unit by SKU M208.201 or GTIN 4054469105352; the unit is listed under the Metav IndustryLine range. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Get reliable runout results in just 10 seconds
Metav runout measuring devices, also referred to as runout testers or runout gauges, enable fast on-machine runout measurement and runout testing. The range includes units that work with centres, so measurements can be performed directly at the machine spindle or on a lathe tailstock without additional fixturing.
Why these devices matter in the workshop
Runout testing verifies the precision of rotating components such as shafts, spindles and workholding fixtures. During a check, the component is clamped and rotated while a dial gauge on a dial gauge holder records deviations. This process identifies form and alignment errors that would otherwise lead to scrap, rework or premature bearing and gear failures. The method is particularly relevant for external, internal and face surfaces of rotational parts used in gearboxes, engine assemblies and driveshaft production.
Measurable advantages that improve throughput
- Fast verification: measurement can be completed in 10 seconds and requires no prior specialist training.
- Significant downtime reduction: setup and machine stoppages can be cut by up to 80% with quick, on-machine checks.
- Versatile inspection: suitable for external, internal and face surfaces, and capable of assessing coaxiality of two or more diameters.
- High accuracy for critical parts: ideal for shafts, bushings, gears and bearings where runout determines service life.
- Flexible geometry handling: adapted for different diameters and profiles, reducing the need for multiple instruments.
Why choose Metav as your precision partner
Metav combines decades of metrology know-how with a broad, pragmatic range of workshop solutions. As a quality filter based in Emmerich, Metav supplies a comprehensive offering from precision tools to complete workshop equipment. More than 48,000 customers trust Metav, and the portfolio exceeds 250,000 products, making Metav a reliable single source for runout measuring devices and complementary metrology instruments. For challenging production requirements, Metav runout testers are positioned as the practical, professional choice.
Quick wrap-up
Runout measuring devices from Metav provide rapid, on-machine runout testing with tailstock centres, enabling fast decision-making, reduced machine downtime and reliable coaxiality and face runout assessment.
FAQ
What can I inspect with a runout measuring device?
A runout measuring device is designed for external, internal and face surfaces of rotational parts. It is commonly used to check shafts, bores, gears and bearing seats for form and alignment deviations.
How long does a standard runout test take?
A runout test with a calibrated dial gauge setup can be completed in as little as 10 seconds, making runout testers suitable for inline checks and short-series production.
Can these devices measure coaxiality between multiple diameters?
Yes. Metav runout measuring devices are capable of determining the coaxiality of two or more diameters and can be used for face runout measurements where concentricity is critical.
Do I need special training to use a runout tester?
No specialist training is required for basic runout checks; the procedure is straightforward and can be carried out without prior knowledge. For process integration and tolerance analysis, Metav’s technical team can provide guidance and application support.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com