Take advantage of a durable HSS construction and a double‑ended design that extends service life while delivering clean holes in thin sheet metal; order the item directly via Metav Werkzeuge or consult the specialists for application advice. Double‑ended drill bit 3.1 mm HSS bodywork drill TECWERK — short‑helix, cylinder shank, profile‑ground Double‑ended drill bit 3.1 mm HSS bodywork drill TECWERK is a purpose‑built tool for efficient drilling in thin materials, especially sheet metal, using hand‑held drills or small bench machines HSS profile‑ground for precise edges Short helix suited to thin materials Double‑ended for extended tool life Cylinder shank for standard chucks Clean, reliable holes in thin sheet materials The HSS construction and profile‑ground geometry provide a reliable cutting edge that reduces burr formation when working with thin metals. With a 3.1 mm cutting diameter and a short helix, the bit controls chip evacuation and prevents the material from snagging, which is particularly important for bodywork and panel applications. The cross point ensures rapid centring without pilot drilling, delivering repeatable, clean results while maintaining drilling speed and reducing rework. Built for longer uptime and straightforward handling The double‑ended layout effectively doubles usable life per tool, allowing a quick flip to a fresh cutting end when wear occurs, which minimises changeover time on the shop floor. The cylinder shank fits standard chucks on hand drills and compact drill presses, enabling fast tool changes and steady running. As the bit is right‑hand cutting and short‑spiral, it is optimised for manual drilling in thin sheets where control and process reliability are priorities. Compatibility and application scope explained This bodywork drill is specifically designed for drilling thin materials and is primarily suited to sheet metal work with hand‑held drilling equipment. The geometry and material selection make it effective for fast, controlled penetration without excessive burr. For users less familiar with technical terms: short helix refers to a reduced spiral length that improves stability in thin parts, while profile‑ground indicates a machined cutting profile for consistent edge geometry and improved life. Confidence through quality and practical support Sourcing from established supply channels ensures consistent quality control and traceability. Metav combines a broad product range with a local quality filter in Emmerich, supporting workshops and industry with reliable delivery and technical transparency. The product’s plain finish and straightforward design emphasise practical performance and easy disposal at end of life, while the robust HSS material offers wear resistance under typical sheet‑metal drilling conditions. Contact Metav Werkzeuge for product availability and application guidance on the TECWERK double‑ended bodywork drill — call +49 2822 7131930 or email info@metav-werkzeuge.com to discuss suitability for specific sheet‑metal tasks Technical Data Article number: 2000860130NW SKU / UID: 2000860130NW Packaging unit: 10 Data Diameter: 3.1 mm Shank: cylinder Pack quantity: 10 pieces Special features HSS material Profile‑ground cutting edges Double‑ended design Right‑hand cutting Cross‑point tip for centring Short spiral / short helix Suited for thin materials and sheet metal Intended use with hand drills and small bench drills Plain finish (blank) FAQ What materials is this drill suitable for? The TECWERK double‑ended bodywork drill is designed primarily for thin sheet metal applications; its short helix and HSS construction support controlled drilling in such materials. Can the bit be used in a drill press or only hand drills? The cylinder shank and robust HSS design allow use in both hand‑held drills and small bench or press machines provided the chuck accepts the shank size. How does the double‑ended design affect maintenance? A double‑ended configuration doubles the available cutting life per tool: when one end wears, the bit can be reversed to use the second end, reducing downtime for replacements. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the double-ended design, HSS cutting edges and profile-ground geometry for reliable drilling of thin sheet metal; order the bits directly via Metav Werkzeuge or consult our specialists for batch needs. TECWERK Double-Ended HSS Bodywork Drill D 3.2 mm — profile-ground, short-spiral bit A TECWERK Double-Ended HSS Bodywork Drill D 3.2 mm designed for fast, clean holes in thin materials and sheet-metal work with hand-held drilling machines HSS, profile-ground cutting edges Short spiral for efficient chip evacuation Cylindrical shank for standard chucks Ideal for thin sheet-metal drilling Precision and consistent holes for sheet-metal work The profile-ground HSS edges and the cross point geometry deliver a stable centre and reduced walking when starting holes in thin panels. This double-ended design ensures rapid tool changes and continuous productivity on the shop floor, while the short spiral promotes reliable chip evacuation in hand-held operations. The combination of these features results in consistently round holes and less rework, supporting a smoother production flow and predictable outcomes in repair shops and small fabrication cells. Simple compatibility and secure clamping for everyday use Equipped with a cylindrical shank, the bit fits conventional chucks on standard hand drills and bench machines, permitting quick swapping between tools. The bright finish makes visual inspection straightforward and helps identify wear at a glance. Right-hand cutting geometry and the compact spiral form mean the tool performs well in manual operations, offering a practical balance between control and drilling speed for technicians working on body panels and other thin gauge materials. Robust cutting behaviour and maintenance-friendly design Made of HSS, the drill provides good wear resistance for general sheet-metal applications; the profile grind keeps cutting edges sharper for longer under typical workshop conditions. The short-spiral flute assists chip release and reduces clogging risks when penetrating thin substrates, lowering friction and improving hole quality. When refurbishment is required, regrinding can be performed by qualified tool service providers to restore geometry, extending the useful life of the bit and reducing replacement frequency. Application benefits that save time in the workshop The bit is primarily intended for thin materials and sheet metal, particularly in bodywork and repair contexts where hand-drill use is common. Its double-ended layout offers an immediate spare cutting end, reducing downtime and increasing throughput on repetitive tasks. The tool’s straightforward specification and familiar shank form make it an economical addition to any workshop toolkit, supporting frequent small repairs and production tasks without complex set-up or special holders. Contact Metav Werkzeuge for stock information and technical advice on TECWERK HSS double-ended bodywork drills, supplied reliably from Emmerich for prompt workshop replenishment Technical data Article number: 2000860131NW UID: 2000860131NW Item label: Doppelendbohrer D.3,2mm HSS Karosseriebohrer TECWERK Brand: TECWERK Core specifications Diameter: 3.2 mm Shank type: cylindrical Spiral: short Cutting direction: right-hand Packaging unit: 10 Special features Material: HSS Profile-ground cutting edges Cross point geometry Double-ended execution (bodywork drill) Bright finish Suited for thin materials and sheet-metal drilling with hand drills FAQ What materials is this drill suitable for? The Doppelendbohrer D.3,2mm HSS Karosseriebohrer TECWERK is specified for thin materials and is primarily intended for sheet-metal and bodywork applications using hand-held drilling equipment. Will the 3.2 mm bit fit a standard hand drill chuck? Yes, the cylindrical shank on the TECWERK double-ended bit is designed for standard chucks, allowing secure clamping in typical hand drills and many bench drill chucks. How does the short spiral affect drilling performance? The short spiral on the TECWERK bit improves chip evacuation in thin materials, reducing clogging and helping to maintain hole quality in manual drilling operations. Can the cutting edges be re-sharpened? Regrinding of the Doppelendbohrer D.3,2mm HSS Karosseriebohrer TECWERK is possible by qualified tool service providers to restore the original profile and extend service life. Is this drill suitable for stainless or hardened steels? The product data specifies suitability for thin materials and sheet metal; applications involving stainless or hardened steel are not listed for this bit and should be validated with technical advice. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Doppelendbohrer D.3,3mm HSS Karosseriebohrer TECWERK Der Doppelendbohrer D.3,3mm HSS Karosseriebohrer TECWERK ist ein speziell für die Blechbearbeitung entwickelter Bohrer, der sich durch seine zwei Schneidenden, die HSS-Legierung und die kurze Spirale besonders für den Einsatz mit Handbohrmaschinen eignet. Doppelendbohrer für dünne Bleche, HSS Zylinderschaft, rechtsschneidend Kreuzanschliff für exakten Ansatz Kurze Spirale für sauberen Spantransport Unbeschichtet, blanke Ausführung Effiziente Bohrleistung für dünne Materialien Der Einsatz eines Doppelendbohrers spart Zeit und Werkzeugwechsel, weil beide Enden genutzt werden können, bevor ein Austausch erforderlich wird. Die HSS-Legierung (Schnellarbeitsstahl) bietet gute Temperaturbeständigkeit beim Bohren in dünnen Blechen und reduziert so thermische Verformungen. Anwender profitieren von gleichbleibender Bohrqualität bei wiederholten Anwendungen in der Blechbearbeitung. Präziser Ansatz und saubere Spanführung Der Kreuzanschliff sorgt für einen definierten, zentrierten Ansatz und vermeidet Springen auf glatten Oberflächen. In Kombination mit der kurzen Spirale entsteht ein kontrollierter Spantransport, der insbesondere bei dünnen Materialien Ausrisse reduziert. Der Zylinderschaft garantiert eine sichere Spannaufnahme in handelsüblichen Handbohrmaschinen und erhöht die Arbeitssicherheit. Praxisgerechte Ausführung für Werkstatt und Karosserie Die blanke, unbeschichtete Ausführung macht den Bohrer robust und unkompliziert in der Nachbearbeitung; Beschichtungen würden bei dünnen Blechen kaum Vorteile bringen. Das Werkzeug richtet sich an Karosseriebetriebe, Montagewerkstätten und Heimwerker, die mit Handbohrmaschinen arbeiten und eine zuverlässige Lösung für präzise Bohrungen in dünnen Blechen suchen. Die Ausführung als Karosseriebohrer ist auf diese Anforderungen zugeschnitten. Materialkenntnis und Einsatzhinweis Als HSS-Werkzeug ist der Bohrer ideal für weiche bis mittelharte Metallbleche geeignet; für gehärtete Werkstoffe sind spezialisierte Bohrer erforderlich. Die profilgeschliffene Schneide sorgt für gleichmäßigen Schnittwinkel und reduziert Nacharbeit. Aufgrund der rechtsschneidenden Geometrie ist die Handhabung auch für weniger geübte Anwender sicher und berechenbar. Setzen Sie auf die verlässliche HSS-Qualität von TECWERK und bestellen Sie direkt über Metav Werkzeuge oder kontaktieren Sie unsere Fachberatung unter info@metav-werkzeuge.com bzw. +49 2822 7131930 für eine individuelle Einsatzempfehlung Produktmerkmale Artikelnummer: 2000860133NW Marke: TECWERK Bezeichnung: Doppelendbohrer D.3,3mm HSS Karosseriebohrer Verpackungseinheit: 10 Fakten Durchmesser: 3,3 mm Verpackungseinheit: 10 Besonderheiten Material: HSS (Schnellarbeitsstahl, hitzebeständig) Ausführung: Karosseriebohrer Schaft: Zylinderschaft Schneidrichtung: Rechtsschneidend Anschliff: Kreuzanschliff Schleifung: Profilgeschliffen Spiralform: Kurze Spirale Oberfläche: Blanke Ausführung Einsatzgebiet: Bohren dünner Materialien, Blechbearbeitung mit Handbohrmaschinen FAQ Was macht den Doppelendbohrer D.3,3mm HSS Karosseriebohrer TECWERK besonders geeignet für Karosseriearbeiten? Der Bohrer kombiniert HSS-Material mit einem Kreuzanschliff und kurzer Spirale, wodurch ein sicherer Ansatz und sauberer Spantransport bei dünnen Blechen gewährleistet sind; die Ausführung als Karosseriebohrer ist speziell auf diese Anwendungen abgestimmt. Lässt sich der Bohrer in normalen Handbohrmaschinen verwenden? Ja, der Zylinderschaft ist für handelsübliche Handbohrmaschinen ausgelegt, sodass der Doppelendbohrer D.3,3mm HSS Karosseriebohrer TECWERK unkompliziert und sicher eingespannt werden kann. Ist der Bohrer beschichtet und wie wirkt sich das aus? Die blanke Ausführung bedeutet, dass kein Beschichtungsmaterial vorhanden ist; das reduziert Kosten und vereinfacht Nachbearbeitung, bei dünnen Blechen bietet das in der Praxis klare Vorteile gegenüber beschichteten Varianten. Welche Verpackungseinheit hat der Artikel mit der SKU 2000860133NW? Der Artikel mit der SKU 2000860133NW wird in einer Verpackungseinheit von 10 geliefert. Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

A cost-effective, precision-ground double-ended HSS twist drill combines fast, reliable holemaking with reduced tool changes for efficient sheet-metal work. Order the TECWERK double-ended 3 mm bodywork twist drill directly via Metav Werkzeuge or consult the Metav specialists for tailored advice. TECWERK double-ended 3 mm HSS bodywork twist drill — short spiral, cross-point A TECWERK double-ended 3 mm bodywork twist drill designed for clean, controlled drilling in thin materials and sheet-metal applications with hand-held drills Profile-ground HSS for precise edges Cylindrical shank for secure chucking Short spiral for thin-sheet applications Cross-point reduces walking on start Consistent, clean holes in thin metal with minimal setup The HSS construction and profile-ground cutting geometry deliver a balance of edge retention and toughness that suits frequent use on thin metals. The 3 mm diameter and double-ended design mean fewer tool swaps and economical use of each bit: when one end wears, the other end is immediately available. The cross-point tip reduces tip wander on start, improving hole position accuracy even when working with hand-held equipment. These attributes translate into steady cycle times and lower rework rates for small-batch and repair tasks. Secure holding and straightforward handling for manual drilling A cylindrical shank provides consistent clamping in standard chucks, reducing slippage and vibration during operation. The short spiral flute geometry aids chip control in thin materials, lowering the risk of burr formation and hook-up on the exit side. The bright or untreated finish offers a clear visual check for wear and simple surface cleaning. Overall, the combination of robust shank and compact flute design supports safe, repeatable holemaking when using hand-held drills in workshop or on-site repair contexts. What the technical terms mean for workshop users A profile-ground twist drill has its cutting edges shaped precisely to create uniform cutting conditions; this improves concentricity and reduces heat build-up at the cutting lips. Right-hand cutting indicates the drill cuts when rotating clockwise in the chuck as usual. The short spiral is optimised for thin-sheet work: shallower flute angle produces smaller chips that are easier to eject when material thickness is limited. These characteristics make the tool particularly suitable for bodywork and light fabrication where controlled, burr-minimised holes are required. Practical use and benefits for everyday workshop tasks The tool is intended primarily for sheet metal and other thin materials, giving a reliable option for repair, maintenance and small fabrication runs. The durability inherent in HSS, combined with the double-ended economy, reduces consumption of spare parts and keeps downtime to a minimum. For operations requiring repeatable small holes, the drill offers a pragmatic mix of precision and convenience that supports quick turnarounds without complex tooling investments. If further technical clarification is required, Metav’s product advisors can outline best-practice feed and speed ranges for specific materials. Choose Metav Werkzeuge for straightforward access to precision tools—contact Metav Werkzeuge for ordering and technical consultation at info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical Data Article number: 2000860129NW Name: Doppelendbohrer D.3mm HSS Karosseriebohrer TECWERK Manufacturer: TECWERK Numbers Diameter: 3 mm Packaging unit: 10 Special features Double-ended bodywork twist drill Material: High-speed steel (HSS) Profile-ground, cross-point tip Cylindrical shank Right-hand cutting, short spiral Suitable for thin materials and sheet metal Bright finish FAQ How suitable is this drill for sheet-metal repairs? The TECWERK double-ended 3 mm HSS bodywork twist drill is designed specifically for sheet-metal applications, offering a short spiral and cross-point for controlled chip formation and reduced wandering. Can the drill be used in a standard hand-held drill? Yes. The cylindrical shank and robust HSS construction make this bodywork twist drill compatible with standard hand-held drills and chucks for workshop and mobile repair tasks. Does the double-ended design affect precision? The double-ended format provides two cutting ends for extended service life; precision is maintained by the profile-ground geometry and cross-point tip, which support accurate centring and consistent hole quality. Is this tool suitable for thicker, harder steels? This drill is optimised for thin materials and sheet metal; for thicker or hardened steels, tools with specialised coatings or geometries are recommended. Metav Werkzeuge can advise on alternatives for high-strength applications. What is the article number for ordering or reference? Reference article number 2000860129NW when ordering the TECWERK double-ended 3 mm HSS bodywork twist drill. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a compact, high-performance drilling solution that combines HSS cutting geometry with a short-spiral profile for clean holes in thin sheet materials; ideal for fast workshop tasks with hand drills. Order directly via Metav Werkzeuge or request technical advice for tool matching and safe supply. Double-ended drill bit 4.1 mm — HSS bodywork drill, TECWERK The double-ended drill bit 4.1 mm is a compact HSS bodywork drill designed for fast, clean drilling in thin sheet materials with standard hand-held drills. HSS high-speed steel for durability Profile-ground for precise cutting Cylindrical shank for standard chucks Short spiral, ideal for thin sheet metal Precise holes in thin sheet metal for reliable assembly The double-ended design and profile-ground point geometry deliver repeatable centring and low burr formation when working on panels and thin plates. Built in HSS (high-speed steel), the bit maintains sharpness under standard workshop speeds, which translates into fewer bit changes and less rework. For light fabrication and repair, this means clearer hole tolerances and faster progression through routine tasks without sacrificing hole quality. Quick compatibility with common hand drills and chucks A cylindrical shank allows direct use in most three-jaw chucks and hand-held drills, keeping setup simple and reducing downtime. The short-spiral flute clears chips efficiently when drilling thin materials, lowering the risk of clogging and overheating at typical hand-drill speeds. This combination supports efficient workflows on the shop floor and in mobile repair situations where ease of use and dependable performance matter. Optimised cutting geometry for sheet metal and thin alloys Right-hand cutting with a cross-ground tip provides consistent cutting action and smooth entry into thin metal surfaces, minimising deformation. The uncoated, bare finish is suitable for typical sheet-metal applications where aggressive coatings are unnecessary and where clean contact with clamping fixtures is preferred. The result is a tool that focuses on predictable performance rather than decorative finishes. Practical workshop benefits and tool selection guidance Because the bit is double-ended, the user effectively carries two cutting edges in one small tool, which extends usable life per item and reduces immediate tool inventory needs. For workshops seeking a straightforward, low-maintenance drilling option for panels, trims and light-gauge fabrication, this tool offers a pragmatic balance of precision, robustness and straightforward handling. For tailored advice on feed and speed settings for specific alloys, technical consultation is available. For tailored tool selection and reliable supply from Emmerich, contact Metav Werkzeuge for expert advice and fast delivery via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 2000860141NW SKU: 2000860141NW Product: Double-ended drill bit 4.1 mm HSS (bodywork drill) Brand: TECWERK Facts Diameter: 4.1 mm Shank: cylindrical Material: HSS (high-speed steel) Pack unit: 10 Special features Profile-ground point Right-hand cutting Cross-ground tip Short spiral flute Bare/uncoated finish Best suited for drilling thin materials with hand drills Primarily for sheet metal/bodywork applications FAQ What materials is this drill bit suited for? The double-ended drill bit 4.1 mm is primarily intended for thin sheet metal and similar thin materials; its geometry and short spiral are optimised for clean performance with hand drills. Can the bit be used in standard hand-held drills and chucks? Yes. The cylindrical shank is compatible with standard three-jaw chucks and common hand-held drill chucks, enabling straightforward mounting and quick tool changes. How does the double-ended design benefit workshop use? A double-ended format provides two usable cutting ends per item, extending service life before replacement and reducing the number of spare bits required for routine jobs. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of HSS construction, a double-ended design and a short-spiral geometry to speed up sheet-metal work with fewer tool changes; order the drill directly via Metav Werkzeuge or ask the consultants for application advice. TECWERK double-ended twist drill Ø 4.2 mm – HSS bodywork drill with cylindrical shank Doppelendbohrer D.4,2mm HSS Karosseriebohrer TECWERK — a compact, high-speed steel twist drill engineered for fast, accurate holes in thin sheets and bodywork panels. Double-ended design for quick change High-speed steel for durable edges Short spiral for thin sheet work Cylindrical shank fits hand drills Faster throughput for thin-sheet production The double-ended geometry delivers a simple, practical advantage: when one cutting end dulls, the component can be rotated to present a fresh tip, reducing downtime and maintaining workflow. Built from HSS, the tool keeps cutting edges longer under the intermittent loads typical of manual drilling, while the profile-ground point improves initial bite and maintains hole quality. This configuration translates into measurable efficiency gains for routine sheet-metal tasks and small repair jobs. Clean holes with reliable centring and chip control A cross point combined with a short spiral gives stable centring and controlled chip formation when working with thin materials. The result is cleaner entry and exit surfaces and fewer burrs, which reduces follow-on finishing. The geometry is optimised for sheet metal and body panels, delivering hole integrity that supports assembly operations without additional deburring steps in many cases. Compatibility and handling for hand-held drilling Designed with a cylindrical shank, the tool fits standard chucks and is particularly suited to hand-held drilling machines. The right-hand cutting direction and compact form make it straightforward to handle during quick maintenance or site repairs. The bright, uncoated finish indicates a tool intended for general-purpose metalworking rather than specialised, coated applications. Durable specification and practical care The combination of HSS, profile-ground flutes and a robust double-ended layout offers a balance between life and cost-efficiency for high-frequency use on thin materials. Regular inspection and light sharpening at the profile will extend service life; in addition, maintaining correct cutting speeds and securing workpieces firmly will preserve hole quality and reduce wear. This drill is a practical choice where reliability and easy replacement are priorities. For stock availability or technical guidance on the TECWERK double-ended twist drill Ø 4.2 mm, contact Metav Werkzeuge for expert advice and prompt supply from Emmerich. Technical data Article number: 2000860142NW Label: Doppelendbohrer D.4,2mm HSS Karosseriebohrer TECWERK Packaging unit: 10 Facts Diameter: Ø 4.2 mm Shank type: cylindrical Pack size: 10 pieces Special features Material: HSS Profile-ground point Right-hand cutting Cross point for improved centring Short spiral for thin materials Double-ended execution Bright finish (uncoated) Optimised for sheet metal and bodywork Suitable for hand-held drilling machines FAQ Is this drill suitable for thin sheet metal? The Doppelendbohrer D.4,2mm HSS Karosseriebohrer TECWERK is specifically designed for thin materials and sheet-metal work, using a short spiral and profile-ground point to produce clean holes. Can the double-ended design reduce downtime? Yes — the double-ended format of the Doppelendbohrer D.4,2mm HSS Karosseriebohrer TECWERK allows quick rotation to a fresh cutting end, reducing tool changes and improving throughput. Will the shank fit standard hand drills? The cylindrical shank of the Doppelendbohrer D.4,2mm HSS Karosseriebohrer TECWERK is compatible with standard drill chucks, making it suitable for common hand-held drilling machines. How does the cross point affect drilling performance? The cross point on the Doppelendbohrer D.4,2mm HSS Karosseriebohrer TECWERK improves centring and reduces wandering, which helps achieve accurate holes in thin sheet materials. Is the bright finish a coated surface for corrosion protection? The bright finish of the Doppelendbohrer D.4,2mm HSS Karosseriebohrer TECWERK denotes an uncoated surface; for corrosive environments or extended life, a coated variant would be preferable. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Data conflict: the brand "TECWERK" is not present in the supplied manufacturer list, so a compliant product description cannot be generated. This issue arises when the provided manufacturer list does not include the specified brand, "TECWERK," which prevents the creation of a product description that adheres to compliance standards. To resolve this, it is essential to verify whether the brand should be added to the manufacturer list or if an alternative approach is required. Ensuring the accuracy and completeness of the manufacturer list is critical for generating compliant product descriptions and avoiding conflicts. Please review the supplied data and update it accordingly to address this discrepancy effectively.

Take advantage of the robust HSS construction, double-ended design and profile-ground cutting geometry for dependable sheet‑metal drilling with hand drills; order directly via Metav Werkzeuge or consult the Metav team for application advice. Double-ended bodywork drill D 5.2 mm HSS — TECWERK, cylinder shank, short spiral Double-ended bodywork drill D 5.2 mm from TECWERK, designed for accurate drilling of thin materials and sheet metal with handheld machines Double-ended HSS for extended use Profile-ground for precise cutting Cylinder shank for secure clamping Short spiral ideal for thin sheet metal Consistent hole quality through profile-ground geometry The profile-ground cutting edges ensure a precise centre and concentricity, reducing runout when working with thin materials. This geometric finish stabilises the cutting action, producing cleaner holes and fewer burrs than standard ground bits. Because the bit is made of HSS, the cutting edges retain sharpness under typical workshop loads; the cross-ground tip reduces walking at the start of the cut, which is especially valuable when using portable drilling machines. The technical result is less rework and a more predictable production flow. Designed for safe clamping and trouble-free use with hand drills A cylinder shank provides reliable seating in standard chucks, improving axial stability and reducing slippage during manual drilling operations. The double-ended layout offers immediate backup when one tip dulls, shortening downtime on the shop floor and maintaining throughput. The short spiral flute geometry is tuned for thin materials: it prevents aggressive chip packing and works hand-in-hand with handheld operation, supporting controlled penetration without excessive feed force. Efficient chip control and reduced workpiece damage The flute form and short helix angle support fast chip evacuation from narrow holes in sheet material, lowering the chance of clogging and heat buildup. In practice this means fewer scorched finishes and reduced need for secondary deburring. The bright finish limits unwanted friction on coated or painted surfaces, helping to preserve the integrity of the workpiece while delivering a clean result — an important consideration for bodywork and light fabrication tasks. Workshop benefits: durable, economical and easy to integrate The combination of HSS wear resistance, a profile-ground point and a right‑hand cutting geometry offers a balance between tool life and cutting performance that suits general workshop use. Packaged in multiples, the item supports predictable stock management and quick replenishment. For production environments that value reliability over novelty, this drill bit family offers a straightforward, low-complexity solution that keeps machines running and reduces interruptions caused by frequent tool changes. Contact Metav Werkzeuge for tailored advice and to source TECWERK double-ended HSS bodywork drills — email info@metav-werkzeuge.com or call +49 2822 7131930 for specification support and ordering from Emmerich. Technical data Article number: 2000860152NW Label: Doppelendbohrer D.5,2mm HSS Karosseriebohrer TECWERK Manufacturer: TECWERK Packaging unit: 10 Facts Diameter: 5.2 mm Packaging unit: 10 Design & special features HSS material Profile‑ground cutting edges Cylinder shank Right‑hand cutting Cross‑ground tip Short spiral flute Bright finish Best suited for drilling thin materials with hand drills, primarily for sheet metal work Execution: bodywork drill FAQ What materials is this drill recommended for? The TECWERK double-ended bodywork drill is primarily intended for thin materials and sheet metal, offering clean cuts when used with hand drills. Can the bit be used in standard hand-held drills? Yes — the cylinder shank and short spiral design make this drill suitable for handheld drilling applications without specialised tooling. How does the cross-ground tip help performance? The cross-ground tip reduces walking at drill start and improves centring, so holes produced by this bit are more accurate and require less rework. What is the advantage of the double-ended design? A double-ended configuration provides a spare cutting tip immediately available on the same tool, extending time between tool changes and supporting continuous workshop operations. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of precise sheet‑metal drilling with a compact, high‑speed steel design and a double‑ended configuration for extended run‑time; order directly via Metav Werkzeuge or ask the consultants for application advice. TECWERK double‑ended HSS sheet‑metal drill bit, Ø 5 mm The TECWERK double‑ended sheet‑metal drill bit is a purpose‑built high‑speed steel cutter for clean holes in thin materials, designed for hand‑held drilling and light workshop production HSS profile‑ground cutting edges Double‑ended design for longer service life Cylindrical shank for secure clamping Short spiral ideal for hand‑drill use Consistent hole quality through material and geometry The bit is manufactured from high‑speed steel (HSS) and profile‑ground to a precise geometry, which reduces heat build‑up and prevents premature wear under normal workshop use. The short spiral flute limits vibration when used with hand drills, producing cleaner holes in thin sheet and panel material and reducing the risk of burr formation. The combination of a cross grind with a right‑hand cutting profile improves centring on the workpiece, so the cutter starts reliably without the need for a pilot pre‑drill. These features translate into lower rework rates and predictable cycle times in small‑batch production. Practical handling and compatibility with common drills A cylindrical shank ensures the bit fits standard chucks securely, enabling quick tool changes and compatibility with a wide range of hand‑held and benchtop drills. The double‑ended layout offers an immediate spare cutting end, cutting downtime in half compared with single‑ended counterparts and extending the effective life of each item. For workshops aiming to keep inventories efficient, this design reduces the frequency of tool replacements and supports steady throughput during repetitive sheet‑metal operations. Application scope and durability for everyday workshop tasks Engineered as a sheet‑metal or bodywork drill, the plain finish and robust HSS composition suit light to medium use on thin materials; the bit is intended primarily for thin‑gauge metals commonly encountered in panel work. The short flute reduces clogging when penetrating coated or painted surfaces and simplifies chip evacuation in thin sections. The geometry and material choice deliver a balance of durability and economical performance, making this cutter an apt choice for maintenance engineers, metalworkers and small fabrication shops that require dependable results without specialist machinery. For reliable results in sheet‑metal drilling with the TECWERK double‑ended HSS bit, contact Metav Werkzeuge for purchasing or technical guidance — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: 2000860150NW Label: Doppelendbohrer D.5mm HSS Karosseriebohrer TECWERK Manufacturer: TECWERK UID: 2000860150NW Packaging unit: 10 Numbers / Core technical data Diameter: 5 mm Packaging unit: 10 pieces Designs / Special features High‑speed steel (HSS) Profile‑ground cutting edges Double‑ended drill bit Cylindrical shank Right‑hand cutting Cross‑grind tip Short spiral / short flute Suited for thin materials and sheet‑metal work Plain (bare) finish Type: sheet‑metal / bodywork drill FAQ What materials can this drill bit cut? The TECWERK double‑ended HSS sheet‑metal drill bit is designed primarily for thin metals and panel work; it performs best on thin sheet and similar materials. Is the shank compatible with standard chucks? Yes, the cylindrical shank is suitable for common hand‑drill and bench‑drill chucks, providing secure clamping during operation. How does the double‑ended design benefit workshop workflow? The two cutting ends halve downtime caused by tool changes, extending service life and improving continuity in small‑batch production with the TECWERK bit. Does the short spiral affect chip evacuation? The short flute reduces vibration and is optimised for thin materials; chip evacuation is efficient in sheet‑metal applications but may differ for thicker workpieces. Is this bit suited to production or only maintenance tasks? Its geometry and HSS construction make it suitable for repetitive workshop tasks and small production runs where reliable, clean holes in thin materials are required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com