Precision built-in calipers for accurate linear positioning
Built-in calipers provide permanent, high-precision measurement of travel and position along linear axes, enabling direct conversion of mechanical motion into reliable digital values that boost productivity and reduce scrap. Designed for robust use in machine tools, fixtures and special machines, these systems allow horizontal or vertical mounting and resist dust, oil and splash water while offering flexible display placement via a separate LCD unit. With features such as zero setting at any position, inch-metric switching and modern data interfaces, these built-in calipers, digital linear measuring systems and linear encoder strips deliver dependable position control for industrial metalworking.
1000mm Built-In Digital Caliper With 10x Magnifier, IP67 - Microtech Metrology
Take advantage of the combination of precision over long distances, robust IP67 protection, and a high‑resolution 0.001 mm readout to keep inline measurement reliable across production runs; order the instrument directly via Metav Werkzeuge or contact our consultants for specification support. Built-in digital caliper — large-range, IP67, Swiss Electronics display by Microtech Metrology The built-in digital caliper provides inline measurement capability for large components and assemblies up to 0–1000 mm, designed for production metrology and fixture integration. IP67 protection for harsh environments Measuring range 0–1000 mm Resolution 0.001 mm for fine increments Swiss Electronics digital display Consistent accuracy where length matters For long-span checks, the instrument combines a maximum measuring range of 0–1000 mm with an accuracy of ±0.03 mm, delivering reproducible results across larger components. Classified in the large caliper category (500–1,000 mm), this design balances reach and stiffness so that measurements remain stable even when gauging long rails, housings or fixture assemblies. The specified accuracy is presented as a clear technical parameter to support routine quality checks and in‑process sampling without overpromising laboratory precision. Built to withstand the shopfloor Sealing to IP67 protects the mechanism from dust and short-term immersion, which is especially relevant where coolant, chips or washdown procedures are common. The sealed electronics combined with a robust mechanical structure reduce the risk of contamination-related drift and downtime. With a Swiss Electronics digital readout and solid construction, the instrument is suited to continuous use in demanding production environments, helping to reduce rework caused by environmental influences. High-resolution readout and practical magnification A fine resolution of 0.001 mm provides clearly legible increments for fine alignment and inspection tasks, while the integrated 10× magnification assists visual verification at the scale of small graduations. The clear digital display simplifies data interpretation for operators and PLC interfaces alike. Because the caliper is designed for built‑in mounting, panel or fixture integration is straightforward, enabling inline measurement stations that feed reliable, repeatable values into quality processes. Streamlined integration and workflow benefits Designed as a built‑in solution, the instrument reduces installation complexity and shortens cycle time for inline measurements. The digital readout and robust enclosure make it compatible with workshop environments where space is structured around production lines or dedicated inspection fixtures. By adopting a calibrated, production‑grade measuring device from a trusted supplier, inspection routines become simpler and non‑value‑adding handling is reduced — an efficiency gain for manufacturing and maintenance teams. Supply reliability and partner assurance Metav’s approach to precision makes high‑quality metrology accessible to workshops and production facilities. Stocked and distributed from Emmerich, the product benefits from a European quality filter and dependable logistics, backed by a long history of service to industry and trade. Choosing a built‑in measuring solution from an established metrology supplier ensures consistent parts inspection and continuity of supply for recurring production needs. Contact Metav Werkzeuge for technical advice on integrating Microtech Metrology built‑in digital calipers into existing fixtures or to request a tailored delivery from our Emmerich warehouse Technical data Article number: 142510151 GTIN: 4061905457500 ECLASS: 21170344 Manufacturer: Microtech Metrology Facts Measuring range: 0–1000 mm Maximum range: 1000 mm Resolution: 0.001 mm Accuracy: ±0.03 mm Magnification: 10× Special features IP 67 protection Swiss Electronics digital display Digital readout (built‑in) Built‑in mounting configuration FAQ What measuring range does this caliper cover? The built‑in digital caliper covers a range of 0–1000 mm, suitable for large components and inline inspection tasks. How precise is the instrument for production checks? Accuracy is specified as ±0.03 mm with a display resolution of 0.001 mm, providing dependable repeatability for workshop and production measurements. Is the device suitable for wet or dusty environments? Yes — the caliper is sealed to IP67, offering protection against dust ingress and temporary immersion, which suits many shopfloor conditions. Which display electronics are fitted? The instrument uses a Swiss Electronics digital display for clear readout and operator convenience. What is the article number for ordering or reference? The SKU for this built‑in digital caliper is 142510151, GTIN 4061905457500. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
1000mm Digital Built-In Caliper Horizontal Stainless, Capacitive System, DIN 862 - Metav IndustryLine
Take advantage of a robust combination of long-range capacity, a capacitive measuring system, and a large protective housing for steady, reproducible workshop measurements; order directly via Metav Werkzeuge or consult our specialists for application matching. Digital built-in caliper M218.161 — 1,000 mm capacitive digital caliper (Metav IndustryLine) The Digital built-in caliper M218.161 is a 1,000 mm capacitive digital caliper for horizontal installation, engineered for long-range industrial measurements in accordance with DIN 862. 1,000 mm measuring range Capacitive measuring system Large, robust housing DIN 862 compliant Precision over long spans for large components The caliper is classified in the large-range (500–1,000 mm) category and therefore combines extended reach with structural stiffness to reduce measurement variability over long distances. With a 1,000 mm measuring length and a solid construction weighing 3.4 kg, the instrument is intended for tasks where repeatability matters across extended surfaces, such as heavy fixtures, housings and large workpieces. The design reduces deflection and supports reproducible results without frequent re-centring of the setup, which speeds up workflow and reduces rework. Fast digital readout and secure data capture A capacitive measuring system paired with a digital display provides easy-to-read values and practical switching between units. The readout supports ON/OFF, mm/inch, ABS/INC and ZERO/PRESET functions and offers a display resolution of 0.01 mm (0.0005 in) for standard workshop accuracy. The caliper includes an RB 2 data interface for secure transfer of measured values into quality logs or SPC systems, enabling faster documentation and fewer transcription errors. These attributes translate into measurable time savings for routine inspections and production checks. Industrial-grade construction and standards conformity Constructed in stainless material with a horizontal mounting orientation and a large housing, the instrument protects the electronics and mechanical parts in demanding environments. Conformity with DIN 862 ensures the caliper follows recognised measuring practice for verifiability and interchangeability. The combination of robust protection and standard compliance makes the tool suitable for production floors, incoming inspection and assembly stations where consistent performance is required. The instrument’s measured accuracy specification supports confident pass/fail decisions at line speed. For tailored specification advice on the Metav IndustryLine 1,000 mm digital built-in caliper or to discuss integration into existing measuring setups, contact Metav Werkzeuge in Emmerich by phone +49 2822 7131930 or e-mail info@metav-werkzeuge.com Technical data Article number: M218.161 GTIN: 4054469111827 Manufacturer: Metav IndustryLine Facts Measuring range: 0–1000 mm Resolution (display): 0.01 mm / 0.0005 in Accuracy: 0.07 mm Weight: 3.4 kg Special features Capacitive measuring system Stainless horizontal design DIN 862 Digital display with ON/OFF, mm/inch, ABS/INC and ZERO/PRESET RB 2 data output Large housing for enhanced protection FAQ What measuring range does this caliper cover? The caliper covers a measuring range of 0–1000 mm; the M218.161 from Metav IndustryLine is designed specifically for long-range workshop and production measurements. Is the display suitable for inch and millimetre readings? Yes, the digital display supports switching between mm and inch and includes ABS/INC and ZERO/PRESET functions for convenient on-the-fly adjustments. How are measured values exported from the instrument? Measured values can be transmitted via the RB 2 data output, enabling direct recording into documentation systems or statistical packages. Does the instrument meet recognized standards? The caliper is manufactured in compliance with DIN 862, providing a recognised basis for industrial measurement practice. For which applications is the large housing particularly beneficial? The large housing protects electronics and sliding mechanics in demanding environments, making the instrument suitable for production, incoming inspection and heavy-component measurement tasks. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1000mm Digital Installation Caliper With Separate Display 0.01mm Resolution, Capacitive System - Metav IndustryLine
Take advantage of a long 1000 mm measuring range, a 0.01 mm resolution and a separately mountable display to combine flexible installation with dependable readings in production environments. Order the caliper directly via Metav Werkzeuge or contact our consultants for integration advice. Digital Built‑in Caliper ALU 1000 mm — Separate display, 0.01 mm resolution (Metav IndustryLine) A Digital Built‑in Caliper ALU 1000 mm designed for workshop and machine‑mounted measurement tasks, offering a long measuring range and a separate display for flexible panel or fixture installation. Separate digital display for flexible mounting 0.01 mm resolution for fine readings 1000 mm measuring range for large parts Aluminium profile beam for low weight Built for long‑range workshop measurement Classified in the large‑format caliper category (500–1,000 mm), this instrument covers measurements up to 1000 mm while keeping handling effort reasonable. The long aluminium profile beam provides a favourable stiffness‑to‑weight ratio, making the device suitable for measuring large housings, fixtures and assembly components without excessive operator fatigue. The built‑in format with a separate display allows mounting the readout where it best fits the production line, reducing the need to reposition parts and increasing throughput. Precise, repeatable readings with an industrial sensor concept The caliper offers a 0.01 mm display resolution and a stated accuracy of 0.1 mm, supported by a capacitive measuring system that delivers stable, low‑wear sensing across the full travel. The separate display integrates ON/OFF, ZERO, mm/inch, ABS and SET functions for straightforward operation and quick toggling between metric and imperial units. The Digital Built‑in Caliper ALU 1000 mm is therefore well suited for inspection tasks where clear readout and straightforward unit selection reduce measurement time and data transcription errors. Installation flexibility and robust construction for everyday use A measuring rod made from an aluminium profile keeps the overall mass low (approx. 1 kg) without sacrificing dimensional stability over the metre length. The built‑in design combined with an external readout supports installation in machines, test benches or stationary fixtures, enabling measurements where access to the beam is possible but space for an integrated display is not. The capacitive system and minimalist mechanical guidance minimise maintenance while providing a durable solution for repetitive workshop use. Efficient quality control and workflow integration Using a long‑range digital caliper with a remote display simplifies quality flows by keeping the readout visible to the inspector or machine operator and by enabling easier integration into existing inspection stations. The combination of a clear, high‑resolution display and a low‑weight beam reduces handling time and the probability of rework caused by uncertain readings. Sourcing this instrument from a specialist supplier in Emmerich helps ensure consistent supply and a pragmatic route to bulk procurement for workshops and small production lines. Discuss integration of Metav IndustryLine’s Digital Built‑in Caliper with Metav Werkzeuge for tailored installation and production advice Technical Data Article number: M218.268 SKU: M218.268 GTIN: 4054469163888 Manufacturer: Metav IndustryLine Category: Calipers Facts Measuring range: 0–1000 mm Resolution: 0.01 mm Accuracy: 0.1 mm Weight: 1 kg Customs tariff number: 90173000 Special features Capacitive measuring system Separate digital display with ON/OFF, ZERO, mm/inch, ABS and SET Aluminium profile measuring rod Built‑in design for panel or fixture mounting Digital operation, metric and imperial units FAQ What measuring range does this caliper cover? The instrument measures from 0 to 1000 mm; the Digital Built‑in Caliper ALU 1000 mm (SKU M218.268) is intended for large workpieces up to one metre. What resolution and accuracy are provided? This caliper provides a 0.01 mm resolution and a stated accuracy of 0.1 mm, using a capacitive measuring system to maintain stable readings across the full travel. Can the display be mounted away from the beam? Yes, the separate digital display is designed for remote mounting, allowing the readout to be positioned independently of the aluminium measuring rod to suit fixtures and machine panels. What is the measuring rod made from and how heavy is the unit? The measuring rod is an aluminium profile, which keeps the total weight around 1 kg while preserving stiffness needed for reproducible measurements. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1000mm Digitaler Einbaumessschieber, 0,001mm Auflösung, IP 67, Swiss Electronics Display - Microtech Metrology
Höchste Präzision, robuster Schutz und großer Messbereich verbinden sich hier zu einem zuverlässigen Messsystem. Nutzen Sie die Genauigkeit von 0,03 mm, die Auflösung von 0,001 mm und den IP67‑Schutz für reproduzierbare Messungen auch unter rauen Produktionsbedingungen. Bestellen Sie das Gerät direkt über Metav Werkzeuge oder kontaktieren Sie unsere Beratung für technische Rückfragen. Einbaumessschieber von Microtech Metrology Der Einbaumessschieber ist ein digitaler Messschieber für Langmessungen bis 1.000 mm und eignet sich für präzise Qualitätskontrolle in Industrie und Fertigung. Einbaumessschieber »142510146« von Microtech Metrology IP67 Schutz gegen Wasser und Staub Auflösung 0,001 mm für hochpräzise Messungen Messbereich bis 1.000 mm für große Bauteile Digitale Anzeige Swiss Electronics für klare Ablesung Präzision für reproduzierbare Messprozesse Die Genauigkeit von 0,03 mm kombiniert mit einer Auflösung von 0,001 mm sorgt für Messwerte, die Nacharbeit reduzieren und Toleranzüberschreitungen frühzeitig erkennbar machen. Durch die feine Auflösung eignen sich Messungen für Serienprüfungen und Werkzeugabgleiche, bei denen kleinste Abweichungen zu Funktionsstörungen führen können. Die digitale Anzeige ermöglicht schnelle Erfassung und minimiert Ablesefehler, was die Effizienz in der Qualitätskontrolle erhöht. Robuste Ausführung für den harten Werkstattalltag Mit dem IP67‑Schutz bietet das Gerät Schutz gegen eindringendes Wasser und Staub und ist damit für feuchte oder verschmutzte Fertigungsbereiche geeignet. Die Konstruktion als Einbaumessschieber ist auf feste Montage ausgelegt und garantiert stabile Führung auch bei langen Messstrecken. Dieses Modell gehört zur Klasse Mit Gross (Messbereich bis 1.000 mm) und ist damit prädestiniert für großformatige Bauteile, ohne die Steifigkeit zu opfern. Einsatzbereiche und Zielgruppe mit klarem Nutzen Das Messgerät richtet sich an Fertigungsbetriebe, Vorrichtungsbauer und Qualitätslabore, die auf zuverlässige Langmessungen angewiesen sind. Für Anwender in der Rohr‑ und Behälterfertigung sowie in der Schwerzerspanung bietet der große Messbereich klare Vorteile, weil größere Bauteile ohne Umspannen gemessen werden können. Die digitale Anzeige erleichtert die Einbindung in Prüfprozesse und reduziert Einarbeitungszeiten bei wechselnden Bedienkräften. Einfache Integration und klare Bedienbarkeit Die digitale Anzeige von Swiss Electronics sorgt für schnelle, eindeutige Ablesungen direkt an der Maschine oder im Messraum. Das kompakte Einbauformat erlaubt eine dauerhafte Integration in Prüfvorrichtungen, sodass Messzyklen automatisiert und stabil ablaufen können. Durch die Kombination aus robuster Bauweise und feiner Auflösung lässt sich die Messkette insgesamt optimieren und die Prozesssicherheit erhöhen. Für zuverlässige Langmessungen empfiehlt sich der Einbaumessschieber von Microtech Metrology; technische Beratung und Bestellung erhalten Sie direkt über Metav Werkzeuge per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930. Produktmerkmale Artikelnummer: 142510146 Marke: Microtech Metrology Bezeichnung: Einbaumessschieber GTIN: 4061905459955 Digitale Anzeige: Swiss Electronics IP Schutz: IP 67 Fakten Genauigkeit: 0,03 mm Messbereich: 0–1.000 mm Ablesung: 0,001 mm Besonderheiten Digitale Ausführung IP67 Schutz gegen Eindringen von Wasser und Staub Einordnung: Klasse Mit Gross (Messbereich bis 1.000 mm) ECLASS: 21170344 FAQ Wie genau ist die Messung mit dem Einbaumessschieber von Microtech Metrology? Der Einbaumessschieber von Microtech Metrology bietet eine Genauigkeit von 0,03 mm bei einer Auflösung von 0,001 mm, sodass er für feine Toleranzen in Fertigung und Qualitätssicherung geeignet ist. Ist das Gerät für den Einsatz in feuchten Produktionsumgebungen geeignet? Ja, der Einbaumessschieber verfügt über IP67‑Schutz, wodurch er gegen Staub und zeitweiliges Untertauchen geschützt ist und sich für feuchte oder verschmutzte Arbeitsbereiche eignet. Für welche Bauteilgrößen eignet sich dieser Messschieber besonders? Mit einem Messbereich bis 1.000 mm gehört das Gerät zur Klasse Mit Gross und ist speziell für großformatige Bauteile und Vorrichtungen konzipiert, die ohne Umspannen gemessen werden sollen. Welche Anzeige verwendet der Messschieber und wie erleichtert sie die Arbeit? Die digitale Anzeige von Swiss Electronics liefert klare Ablesungen und reduziert Fehler bei der Datenerfassung, was Prüfabläufe beschleunigt und die Prozesssicherheit erhöht. Welche Identifikationsnummern sind für das Produkt relevant? Das Produkt ist als Einbaumessschieber mit der Artikelnummer 142510146 und der GTIN 4061905459955 geführt. Hersteller: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
1000mm Digitaler Einbaumessschieber, 0,01mm, IP 67 - Microtech Metrology
Profitieren Sie von hoher Genauigkeit, robustem IP 67 Schutz und einem großen Messbereich 0–1000 mm für reproduzierbare Messungen in der Produktion. Bestellen Sie den Einbaumessschieber direkt über Metav Werkzeuge oder nutzen Sie unsere Beratung bei technischen Fragen. Einbaumessschieber Digitaler Messschieber von Microtech Metrology Einbaumessschieber mit großem Messbereich und robuster Elektronik für den Einsatz in rauer Umgebung IP 67 Schutz für feuchte und staubige Umgebungen Messbereich 0–1000 mm, geeignet für Großkomponenten Ablesung 0,01 mm für präzise Ergebnisse Big Screen Swiss Electronics für klare Anzeige Digitale Messung, ideal für Fertigung und Qualitätssicherung Robuste Präzision für die Fertigung Der Einbaumessschieber bietet präzise Ablesung und eine Messgenauigkeit von 0,05 mm, wodurch er sich für Standardmessungen im Maschinenbau eignet. Durch die fein aufgelöste Anzeige von 0,01 mm lassen sich Toleranzen sicher kontrollieren. Die Kombination aus stabiler Mechanik und sensibler Elektronik sorgt für konstante Messergebnisse, die Prüfzyklen verkürzen und Ausschuss reduzieren. Großes Einsatzspektrum dank erweitertem Messbereich Mit einem Messbereich bis 1000 mm fällt dieses Messgerät in die Kategorie Mit Gross und deckt damit großformatige Bauteile und Vorrichtungen ab. Anwender profitieren von der Balance aus Reichweite und handhabbarer Führung, wodurch Messungen an Gehäusen, Aufnahmen oder Spannmitteln effizient möglich sind. Die Bauform wurde auf reproduzierbare Messungen über lange Distanzen ausgelegt. Schutz und Bedienkomfort in rauer Umgebung Der Schutzgrad IP 67 garantiert dauerhafte Funktion auch bei Staubbelastung und zeitweiligem Untertauchen, was die Einsatzmöglichkeiten in Fertigungshallen erweitert. Die Big Screen Swiss Electronics Anzeige liefert klare Lesbarkeit bei schwierigen Lichtverhältnissen und reduziert Ablesefehler, sodass Messungen schneller dokumentiert werden können. Integration und Werkstattnutzen Als digitale Ausführung eignet sich dieses Messgerät für die Einbindung in Prüfabläufe, wobei die einfache Handhabung die Ein-Mann-Bedienung unterstützt. Die robuste Konstruktion minimiert Nacharbeit, und die präzise Anzeige vereinfacht die Übergabe der Messergebnisse an nachgelagerte Prozesse. Das Gerät ist speziell für Anwender konzipiert, die hohe Wiederholgenauigkeit und Praxistauglichkeit erwarten. Empfehlen wir, den Microtech Einbaumessschieber mit IP 67 Schutz bei Metav Werkzeuge anzufordern — persönliche Beratung und Verfügbarkeit telefonisch oder per eMail unter info@metav-werkzeuge.com, Telefon +49 2822 7131930 Produktmerkmale Artikelnummer: 142510147 Marke: Microtech Metrology Bezeichnung: Einbaumessschieber GTIN: 4061905459702 Fakten Ablesung: 0,01 mm Genauigkeit: 0,05 mm Messbereich: 0-1000 mm Messbereich Max: 1000 mm Besonderheiten IP Schutz: IP 67 Digitale Anzeige: Big Screen Swiss Electronics Digitale Ausführung Kategorie: Mit Gross (Messbereich bis 1000 mm) FAQ Wie genau ist die Messung mit diesem Einbaumessschieber? Der Einbaumessschieber von Microtech Metrology liefert eine Ablesung von 0,01 mm und eine Genauigkeit von 0,05 mm, sodass er für Standardprüfungen in Fertigung und Qualitätskontrolle verlässliche Ergebnisse bietet. Artikelnummer 142510147 dient bei Rückfragen zur schnellen Identifikation. Für welche Anwendungen eignet sich der Messbereich bis 1000 mm? Der Messbereich bis 1000 mm macht den Einbaumessschieber geeignet für größere Bauteile wie Gehäuse, Aufnahmen und Vorrichtungen in der Schwerzerspanung oder im Formenbau; die Kategorie Mit Gross bietet hier das optimale Verhältnis aus Reichweite und Steifigkeit. Ist das Gerät für den Einsatz in feuchter Umgebung geeignet? Ja, der Einbaumessschieber verfügt über IP 67 Schutz, wodurch er gegen Staub und zeitweiliges Untertauchen geschützt ist und sich somit auch in anspruchsvollen Produktionsumgebungen einsetzen lässt. Hersteller: Microtech Metrology; Microtech, Nizhneyurkovska str., 45a; 04080 Kyiv; Ukraine; tool@microtech.tools
1000mm Inline Digital Caliper Color 2.4" Touchscreen, Wireless USB, IP54 – Microtech Metrology
Combine dependable 0.04 mm accuracy, a 0.01 mm resolution and Wireless+USB data transfer for faster quality control and fewer manual entries; order the instrument directly via Metav Werkzeuge or ask our consultants for integration advice. Built-in digital caliper — 0–1000 mm range, Colour 2.4" touchscreen (Microtech Metrology) The built-in digital caliper is a long-range, stainless steel measuring solution for workshop and production environments, designed to capture reliable dimensional data up to 1000 mm. 0–1000 mm measuring range 0.01 mm resolution on digital display Wireless and USB data transfer IP54 protection for workshop use Faster measurement with traceable precision This measuring instrument delivers a stated accuracy of 0.04 mm combined with a resolution of 0.01 mm, which reduces uncertainty in routine checks and helps maintain production tolerances. The numeric specifications translate directly into fewer rejected parts and more predictable process control; by reducing the need for repeat measurements, throughput is improved. The calibration to ISO 17025 (certificate supplied) provides documented traceability for audits and quality management systems. Robust design and practical data handling Constructed from stainless steel, the unit resists workshop wear while the IP54 rating shields electronics from dust and splash exposure. The 2.4" colour touchscreen provides a clear readout and simple menu navigation, while dual data interfaces (wireless and USB) enable fast transfer into inspection software or measurement logs. These features cut manual entry time and minimise transcription errors, supporting leaner inspection routines on the shop floor. Built for larger components and fixture work With a measuring span up to 1000 mm, this caliper belongs to the large-range class used for sizeable components, jigs and housings where profile stiffness and repeatability matter. The extended range makes the instrument suitable for toolrooms, fixture assembly and heavy‑duty machining inspection, offering a practical balance between reach and handling. The built-in format is particularly useful where the measuring system needs to be integrated into fixed stations or custom test rigs. Ready for quality assurance and Industry 4.0 workflows Delivered fully calibrated under ISO 17025, the device arrives with a calibration certificate, enabling immediate use in accredited inspection processes. The combination of digital output and robust metrological documentation simplifies linking measurement results to statistical process control and traceability records. This reduces administrative overhead and supports compliance with internal and external quality requirements. Contact Metav Werkzeuge in Emmerich by e-mail at info@metav-werkzeuge.com or by telephone on +49 2822 7131930 to discuss how Microtech Metrology's built-in digital caliper can be integrated into existing measurement routines and production control systems Technical data Article number: 142510140 GTIN: 4061905037528 Product: Built-in digital caliper Manufacturer: Microtech Metrology Facts Measuring range: 0–1000 mm Resolution: 0.01 mm Accuracy: 0.04 mm Display: Colour 2.4" touchscreen Protection class: IP54 Special features Material: Stainless steel Data output: Wireless and USB Digital caliper Supplied calibrated to ISO 17025 with certificate FAQ What measuring range does the instrument cover? The built-in digital caliper covers a measuring span of 0–1000 mm, suitable for larger components and fixture inspection. Is the caliper supplied with a calibration certificate? Yes — the instrument is delivered fully calibrated to ISO 17025 and includes the calibration certificate for immediate use in quality-assured processes. How can measurement data be transferred from the device? Measurement data can be exported via the integrated wireless interface or by USB connection, enabling straightforward logging into inspection software or SPC systems. What protection does the housing offer in workshop conditions? The caliper is rated IP54, providing protection against dust ingress and splashing water, making it appropriate for typical workshop environments. Which material is the measuring device made from and why is that important? The device is made from stainless steel, which offers corrosion resistance and mechanical robustness for frequent use in production settings. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
1000mm Precision Digital Installation Caliper With Remote Display 0.01mm Resolution, Steel Beam, Magnet Back, 2xCR2032 - Metav IndustryLine
Benefit from the combination of a 1000 mm measuring range, 0.01 mm resolution and a separate remote display for flexible installation in production environments; order directly via Metav Werkzeuge or consult our specialists for integration options. Digital built-in caliper ABS M218.278 — 1000 mm, separate display, 0.01 mm (Metav IndustryLine) The Digital built-in caliper ABS M218.278 is a large-range digital caliper with a separate display, designed for accurate length checks and shop-floor measurement of long components. Large 1000 mm measuring range High resolution 0.01 mm display Separate remote display for flexible readout Rear magnet for secure mounting Reliable measurement across long spans This instrument is designed as a large-range caliper (500–1,000 mm class) suitable for measurements where beam stiffness and repeatability matter. The robust steel beam and balanced mass (approx. 3.4 kg) reduce bend and vibration during handling, which helps to maintain measurement consistency over long runs. In environments where every millimetre counts across larger components, the combination of beam rigidity and a calibrated digital system provides a dependable baseline for process control and reduces the need for repeat checks. Precision data output for production workflows Equipped with an absolute measuring system, the caliper offers a display resolution of 0.01 mm and a specified accuracy of ±0.06 mm, which supports routine quality checks and dimensional verification on larger parts. The separate display decouples the readout from the beam for ergonomic viewing, while the integrated data outputs RB6 and Micro‑B and the supplied connection cable (approx. 2 m) allow direct connection to controllers or statistical process control systems. The display supports readouts in mm, inch and fraction, enabling straightforward documentation and downstream data capture. Practical operation and secure mounting on the shop floor Everyday usability is improved by features such as pre-set and hold measurement and a magnetic rear face for temporary attachment to metal fixtures. These functions allow operators to capture and retain a measured value while performing subsequent tasks, reducing handling errors. The separate display improves visibility in confined or awkward setups, and the device is powered by 2×CR2032 cells, keeping replacement simple and standardised. Together, these features streamline repetitive measurement tasks and contribute to a steadier production rhythm. Metav IndustryLine: precision made accessible Metav IndustryLine positions high-precision equipment within reach of workshops and production lines. With a quality filter based in Emmerich and a broad product range, Metav combines technical competence with reliable supply. Choosing this caliper means opting for a measured approach to quality control backed by a supplier experienced in metrology and workshop equipment, helping to keep inspection throughput predictable and traceable. For bespoke installation advice, data‑integration options or to discuss the separate-display setup contact Metav Werkzeuge in Emmerich by phone +49 2822 7131930 or by e‑mail at info@metav-werkzeuge.com — our consultants advise on adapting the device to specific workflows. Technical data Article number: M218.278 GTIN: 4054469163925 Manufacturer: Metav IndustryLine Material: Steel Range: 0–1000 mm Numbers / Core technical data Resolution: 0.01 mm (display) Resolution (inch): 0.0005 inch Accuracy: ±0.06 mm Weight: 3.4 kg Power: 2×CR2032 Connection cable: approx. 2 m Special features Separate display included Absolute measuring system Data outputs: RB6 and Micro‑B Pre‑set and hold measurement Rear magnet for mounting Digital readout in mm / inch / fraction Tariff number: 90173000 FAQ What resolution and accuracy can be expected from this caliper? The Digital built-in caliper ABS M218.278 offers a display resolution of 0.01 mm and a stated accuracy of ±0.06 mm, making it suitable for large-format dimensional checks where that tolerance matches the process requirements. Can the separate display be positioned away from the beam and integrated into a system? Yes. The caliper includes a separate remote display and a connection cable of approx. 2 m; it provides RB6 and Micro‑B outputs for straightforward integration with data loggers or SPC equipment. Is an accredited calibration included with the standard delivery? The product data do not specify an ISO‑accredited calibration by default. For an accredited ISO 17025 calibration certificate or special calibration services, Metav Werkzeuge can provide options on request. Which applications are suitable for this 1000 mm caliper? The instrument is optimised for shop‑floor measurement of large components such as fixtures, housings and long assemblies where a stiff beam and remote readout improve repeatability and operator ergonomics. What is included in the delivery and what powers the unit? Included: connection cable (approx. 2 m) and a separate display. The unit is powered by 2×CR2032 cells (battery type specified). Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
100mm Digital Flush-Mount Caliper Bidirectional Measurement, Capacitive System, DIN 862 - Metav IndustryLine
Take advantage of the combination of precise capacitive measurement, a compact 100 mm range and DIN‑compliant construction for reliable, repeatable checks at the production line. Order directly via Metav Werkzeuge or consult the team for integration advice. Digital built-in caliper M218.252 (100 mm, stainless, DIN 862) — Metav IndustryLine The Digital built-in caliper M218.252 is a vertical, stainless steel, 100 mm caliper intended for flush mounting where compact, DIN‑862‑compliant digital measuring is required in workshop and production environments. 100 mm measuring range, DIN 862 compliant Capacitive measuring system with 0.01 mm reading Bidirectional measurement capability Stainless vertical design for flush mounting Accuracy and performance that reduces rework The built‑in design combines a capacitive measuring system with a standard digital readout to deliver a 0.01 mm reading and an industry‑grade ±0.02 mm accuracy (specified for this measuring range). This means fewer ambiguous measurements and a lower risk of rework: the capacitive system records position changes without mechanical wear, improving long‑term repeatability. In practice, the compact 100 mm format is ideal for routine quality control and inline checks where space is limited but precision remains essential. Integration and data handling for efficient production Designed for flush mounting, the instrument provides a reliable electrical interface (RB 5) and a multifunction display with ON/OFF, mm/inch, zero/ABS, TOL and HOLD functions for straightforward setup and tolerance control. The built‑in configuration simplifies installation into jigs or fixtures, enabling direct measurement transfer to data acquisition systems and reducing manual logging. The combination of digital output and straightforward controls speeds up inspection cycles and supports traceable production workflows. Practical benefits for workshop and small‑series manufacturing At a weight of just 0.35 kg and a compact construction, this caliper is easy to mount and keeps the measuring station uncluttered. The vertical, stainless design resists shop contaminants and suits both machine tool enclosures and assembly stations. Compliance with DIN 862 provides a common reference for calibration and process documentation; together with the device’s bidirectional measurement capability, it supports a wide range of contact‑based checks from simple outside measurements to dedicated fixture applications. Why this instrument suits quality‑minded teams The caliper’s technical balance—compact range, capacitive sensing and dependable digital output—addresses the principal need of production teams: fast, reproducible checks with minimal setup time. Metav’s curated range and warehouse in Emmerich act as a quality filter for the European market, giving purchasing teams confidence that the instrument meets workshop demands and will be supported across the supply chain. The result is a measurable reduction in inspection time and better alignment with process control targets. For specification matching, integration details or to place an order for the Metav IndustryLine M218.252 built‑in caliper, contact Metav Werkzeuge GmbH in Emmerich at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss your application and delivery options. Technical Data Article number: M218.252 GTIN: 4054469111841 Manufacturer: Metav IndustryLine Facts Measuring range: 0–100 mm Reading resolution: 0.01 mm Accuracy: ±0.02 mm Weight: 0.35 kg Tariff number: 90173000 Measurement system: capacitive Standard: DIN 862 Special features Vertical, stainless design for flush mounting Digital display with ON/OFF, mm/inch, zero/ABS, TOL, DIR, HOLD functions Data output: RB 5 Bidirectional measurement capability FAQ Is this caliper suitable for use on the shop floor for routine checks? Yes. The M218.252 from Metav IndustryLine combines a stainless vertical housing with digital readout and a capacitive sensing system, making it robust enough for routine shop‑floor checks while retaining factory‑level accuracy. What level of accuracy and resolution can be expected? The instrument offers a 0.01 mm reading resolution with an accuracy specification of ±0.02 mm within the 0–100 mm range, appropriate for standard machine‑shop quality control tasks. Can the caliper transmit measurements to a data logger or PLC? Yes. The device includes an RB 5 data output suitable for connection to data collection systems, enabling digital transfer of measurement values for traceability and statistical process control. Does the caliper come ready for mounting in fixtures? The M218.252 is designed as a built‑in (flush) caliper, which simplifies integration into fixtures and jigs for inline measurement applications; electrical and mechanical mounting points are arranged for compact installation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
100mm Digital Precision Caliper Horizontal Small Body Stainless Steel DIN 862, 0.01mm Readout - Metav IndustryLine
Benefit from a compact, installation-ready instrument that combines a hardened stainless steel construction with a 0.01 mm digital display for dependable shop-floor checking; order the digital built-in caliper directly via Metav Werkzeuge or ask our consultants if needed. Digital built-in caliper M218.153.N — 100 mm compact, hardened stainless steel, DIN 862 (Metav IndustryLine) The Digital built-in caliper M218.153.N is a compact, DIN‑862‑compliant 100 mm caliper designed for precise, space-saving measurements in production and assembly settings. Compact 100 mm built-in digital caliper 0.01 mm display resolution Hardened stainless steel construction DIN 862 compliant small housing Precise integration for tight installation spaces The compact, built-in format of this instrument makes it suitable for recessed installation or use where external calipers would be too bulky. Classified in the micro range (measurement range up to 100 mm), the device is optimised for fine mechanical tasks and component checks where limited jaw length and low torsion are an advantage. The small housing and horizontal orientation reduce interference in confined fixtures while retaining a robust measuring head, so inline inspection becomes practical without sacrificing handling or throughput. Measurable accuracy that supports production decisions A 0.01 mm display resolution combined with a declared accuracy of ±0.02 mm delivers results that meet standard workshop and quality‑control requirements. The digital readout features ON/OFF, ZERO, UNIT and HOLD functions for efficient process work and clear readouts at the point of measurement. This balance of resolution and accuracy supports rational decision-making on the shop floor: faster pass/fail checks, reduced rework and consistent assembly quality thanks to reproducible readings. Durable materials and standards for long service life Constructed from hardened stainless steel, the caliper resists corrosion and mechanical wear common in industrial environments. Compliance with DIN 862 gives a recognised baseline for caliper geometry and performance, simplifying integration into existing inspection routines. The instrument runs from a 3 V supply and includes a compact, maintenance‑friendly design that lowers downtime and maintains measurement confidence under frequent use. Data output and practical handling for efficient workflows A dedicated RB 5 data output enables straightforward integration with inspection logs or data acquisition systems when required, supporting traceability and digital documentation. At a weight of just 0.2 kg, the unit is light enough for easy handling during assembly checks yet rigid enough for reliable contact measurement. The combination of built‑in mounting, digital convenience and standardised output reduces time spent on manual transcription and improves overall process efficiency. Choose Metav IndustryLine’s compact built‑in caliper for reliable, space‑saving precision; contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 for specification matching and fast supply Technical data Article number: M218.153.N GTIN: 4054469160733 Category: Calipers Data Measuring range: 0–100 mm Resolution: 0.01 mm / 0.0005 in Accuracy: ±0.02 mm Weight: 0.2 kg Power supply: 3 V Special features Material: hardened stainless steel Standard: DIN 862 Display: digital with ON/OFF, ZERO, UNIT, HOLD Data output: RB 5 Housing: small, horizontal orientation Built-in caliper for integration eClass: 21170344 FAQ What is the measuring range and resolution of this caliper? The caliper measures from 0 to 100 mm with a display resolution of 0.01 mm. How accurate are the readings under workshop conditions? The instrument provides an accuracy of ±0.02 mm, suitable for standard machine‑shop inspection and quality control tasks. Which materials is the caliper made from and why does that matter? The body is made from hardened stainless steel, which improves corrosion resistance and longevity in industrial environments. Does the caliper provide data output for documentation? Yes, the unit includes an RB 5 data output for connection to data-logging or SPC systems. Is the caliper compatible with DIN standards? The caliper complies with DIN 862, ensuring standardised geometry and interchangeability for caliper‑based checks. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1130mm Digital Einbaumessschieber waagerecht, 0,01mm, DIN 862 - Metav IndustryLine
Die besonders positiven Bewertungen von Metav Werkzeuge stehen für 42.000 überzeugte Kunden. Mache Deine eigenen Erfahrungen und shoppe bei metav-shop.de.! Das wichtigste auf einen Blick waagerecht Messbereich: bis 999mm Ablesung: 0,01mm Material: Messschiene aus Aluminium (30x7,9mm) Ausführung: digital Datenausgang: RB 5 Lang messen, klar entscheiden – bis 999mm Bis 0–999mm deckst du kleine und große Aufgaben ab. Du bleibst flexibel, auch wenn das Teil länger wird. Das spart Zeit und Nerven. Gut für Holz, Metall und Kunststoff. Schauen Sie hier, wie wir die Messbereiche klassifiziert haben. Klassifizierung Messbereiche beim Messschieber. DIN 862 Unser Messwerkzeug basiert vollständig auf den Richtlinien der DIN 862. Dies betrifft sämtliche Produktionsschritte und Kalibrierverfahren ebenso wie die eingesetzten Materialien. Die so gewährleistete Maßhaltigkeit und Wiederholgenauigkeit sorgt für einheitliche Qualitätsstandards und internationale Vergleichbarkeit – ein entscheidender Vorteil bei Audits und Kundenfreigaben. Die Premium Messwerkzeuge von Metav IndustryLine werden von unseren Experten für Messwerkzeuge empfohlen. Metav IndustryLine steht für hervorragende Messwerkzeuge zu einem erstklassigen Preis. Alle Messwerkzeuge werden nach der Produktion gestestet. Sind Sie sich nicht sicher, ob dieses Werkzeug Ihre Anforderungen erfüllt? Oder benötigen Sie ergänzende technische Daten? Kein Problem – wir stehen Ihnen gerne zur Verfügung. ✔️ WhatsApp: +49 170 2837271 📧 eMail: info@metav-werkzeuge.com ☎️ Telefon: +49 2822 7131930 Produktmerkmale: Marke: Metav IndustryLine Bezeichnung: Einbaumessschieber Bestellnummer: M218.361 Zahlen & Daten: Messbereich: 0-999mm Gewicht: 0,7kg Norm: DIN 862 Ablesung: 0,01mm Datenausgang: RB 5 Ablesung in Inch/Zoll: 0,0005 Genauigkeit: 0,07mm Länge: 1130mm Besonderheiten Ausführung: digital Material: Messschiene aus Aluminium (30x7,9mm) Digitalanzeige: mit EIN/AUS-, mm/inch- und NULL-Taste Messsystem: kapazitiv waagerecht Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; www.metav-shop.de; info@metav-werkzeuge.com Worauf man achten sollte, wenn man einen Messschieber kaufen möchte: Neben der Präzision und dem Betriebsbereich sind erweiterte Eigenschaften wie die Funktionalität zum Datenoutput oder die Messkraftverwaltung von großer Signifikanz. Im Umfeld der Qualitätssicherung und in Laboreinrichtungen ist ein Messschieber mit kontrollierter Anwendungskraft besonders hilfreich. Ebenso sollte man überlegen, ob die Kalibrierung des Messschiebers erforderlich ist. Die Möglichkeit zur Kalibrierung besteht unmittelbar bei Entgegennahme; zur Sicherstellung der Prozessstabilität sollte regelmäßig jährlich neu kalibriert werden.
1150mm Built-In Digital Caliper Color Touchscreen, Wireless/USB, ISO 17025 Calibrated - Microtech Metrology
The combination of a 1,150 mm measuring range, 1 µm resolution and ISO 17025 calibration ensures reliable long‑range precision with traceable results; order the instrument via Metav Werkzeuge or contact the consultants for tailored advice. Built-in Caliper — Long-range digital caliper with Wireless + USB connectivity (Microtech Metrology) The built-in caliper is a digital measuring instrument designed for integration into production fixtures and measurement stations, providing long‑range length measurement for large components up to 1,150 mm. Wireless + USB data output 1,150 mm measuring range Colour 2.4" touchscreen display Supplied calibrated to ISO 17025 Precise long-range measurement that retains laboratory accuracy With a resolution of 0.001 mm (1 µm) and delivery calibrated to ISO 17025, this digital instrument brings lab-grade accuracy to shop‑floor measurements. The fine reading capability reduces uncertainty when measuring extended components, while the factory calibration and accompanying calibration certificate document traceability for quality systems. By combining a large measuring span with sub‑micrometre steps, the device supports repeatable inspection of assemblies and machined parts where both reach and exactness are required. Streamlined data capture for modern workflows The integrated Wireless + USB data output and the colour 2.4" touchscreen simplify documentation and data transfer. Digital readings can be streamed or exported directly to inspection software or a production database, reducing transcription errors and accelerating reporting. The tactile display speeds up configuration and on‑device checks, while the dual connectivity ensures compatibility with legacy USB setups and wireless factory networks, enhancing measurement throughput without complicating existing IT infrastructure. Designed for long components and practical workshop use Classified in the long caliper category for ranges above 1,000 mm, the instrument balances reach and handling: a lightweight aluminium profile limits sagging while preserving manoeuvrability for larger workpieces. This design choice supports stable measuring geometry across the full 1,150 mm span, so larger housings, fixtures and assemblies can be measured with confidence. An included HD microscope with 7" LED display aids visual inspection and alignment during setting-up, improving the reliability of repeat measurements on complex parts. Robust digital platform and low-maintenance operation The digital readout and touchscreen control reduce moving‑part complexity, lowering maintenance needs and shortening downtime. The aluminium construction offers corrosion resistance and a favourable stiffness‑to‑weight ratio, keeping routine handling comfortable without compromising profile integrity. Supplied as a calibrated system, the instrument arrives ready for use in quality assurance processes, with documentation that supports audit trails and helps integrate the device into standard operating procedures. For integration and procurement of the Microtech Metrology built-in caliper with ISO 17025 calibration, contact Metav Werkzeuge in Emmerich to discuss specifications, compatibility and ordering at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 142510158 GTIN: 4061905036903 Manufacturer: Microtech Metrology Material: Aluminium Included accessory: HD-microscope with 7" LED display Facts Measuring range: 0–1150 mm Resolution: 0.001 mm Display: Colour 2.4" touchscreen Data output: Wireless + USB SKU: 142510158 Special features Supplied calibrated to ISO 17025, calibration certificate included Digital readout and touchscreen control Lightweight long-scale design for large components Integrated data output for direct logging and inspection workflows FAQ What accuracy can be expected across the full measuring range? The instrument offers a resolution of 0.001 mm and is supplied calibrated to ISO 17025; the Microtech Metrology built-in caliper therefore delivers traceable accuracy suitable for high‑precision inspections across the full 1,150 mm span. Is the device ready for immediate use in quality control after delivery? Yes — the caliper is delivered fully calibrated under ISO 17025 and includes the calibration certificate, so it is ready for immediate integration into inspection routines and audit documentation. How are measurement results exported to a PC or database? Measurement data can be transferred via Wireless + USB connectivity; the colour touchscreen enables configuration and on‑device checks before export to standard inspection software or data logging systems. Which applications and materials are suitable for this caliper? The long measuring range and aluminium design make it suitable for inspecting large housings, fixtures, machined assemblies and components encountered in machine building, toolmaking and fixture production. Does the delivery include accessories to aid alignment and visual inspection? An HD microscope with 7" LED display is included, assisting alignment and visual checks during set‑up and measurement of fine features. How is the instrument classified in terms of caliper size categories? With a maximum measuring range of 1,150 mm, the product falls into the "Long" category, intended for extended measurements where lightweight construction and controlled stiffness are important. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
1500mm Built-In Digital Caliper Color 2.4" Touchscreen, Wireless USB, IP54, ISO 17025 Calibrated - Microtech Metrology
Robust stainless‑steel construction, a long 0–1500 mm measuring range and both Wireless + USB data output ensure reliable production measurements with traceable results; the instrument is supplied fully calibrated to ISO 17025 with a calibration certificate. Benefit from the integrated colour touchscreen for fast readback and order the caliper directly via Metav Werkzeuge or consult our specialists for system integration. Built‑in digital caliper — 2.4" colour touchscreen, Wireless + USB (Microtech Metrology) The Built‑in digital caliper is an embedded long‑range measurement solution for machine integration and shop‑floor inspection, offering a 0–1500 mm range and industrial‑grade connectivity. Colour 2.4" touchscreen readout Wireless + USB data output ISO 17025 calibrated with certificate 1,500 mm measuring range IP54 stainless steel construction Precise, traceable measurements for large components This long‑range instrument delivers dependable results for sizeable workpieces thanks to its 0–1500 mm measuring range, which places it in the Long class (1,000–2,000 mm). The calibrated electronics provide a standard resolution of 0.01 mm and an accuracy of ±0.05 mm, enabling routine quality checks that meet industrial tolerances. Supplied fully calibrated to ISO 17025, the device includes a traceable calibration certificate, reducing setup time for quality documentation and simplifying integration into ISO‑compliant inspection routines. Faster data capture and seamless integration with production systems Equipped with a 2.4" touchscreen and both Wireless + USB data outputs, the unit accelerates measurement workflows by removing manual transcription. The colour display makes readings and menus intuitive on the shop floor, while wireless transmission supports mobile data collection and remote logging; USB provides a direct wired option for PLCs or PCs. As a built‑in model it is designed for panel or machine mounting, allowing direct installation into automated setups or gauging stations without the need for additional adapters. Durable design and practical workshop benefits Constructed from stainless steel and rated IP54, the device resists dust and water spray typical of industrial environments and is easy to maintain. The long beam requires attention to straightness and support during handling; when used on larger parts the increased stiffness of the profile preserves reproducibility over the full stroke. Delivered ready for use with a calibration certificate, this instrument reduces downtime and provides a reliable basis for process control and incoming inspection across medium to heavy‑duty applications. For specification advice or procurement of Microtech Metrology built‑in calipers, contact Metav Werkzeuge in Emmerich for tailored guidance and ordering: info@metav-werkzeuge.com, +49 2822 7131930 Technical data Article number: 142515140 GTIN: 4061905036576 Manufacturer: Microtech Metrology ECLASS: 21170344 Product type: Built‑in digital caliper Facts Measuring range: 0–1500 mm Resolution: 0.01 mm Accuracy: ±0.05 mm Display size: 2.4" colour touchscreen Protection class: IP54 Special features Wireless + USB data output Stainless steel construction ISO 17025 calibration and certificate included Long‑range design for large components Built‑in version for machine or panel integration FAQ Is the caliper supplied with a calibration certificate? Yes. The built‑in digital caliper from Microtech Metrology is delivered fully calibrated to ISO 17025 and includes the calibration certificate with the instrument. What measuring range and accuracy can be expected? The instrument covers 0–1500 mm with a resolution of 0.01 mm and an accuracy of ±0.05 mm, suitable for long‑range shop‑floor inspections and fixture measurements (SKU 142515140). Can the device be connected to a PC or data logger? Yes. The unit supports Wireless + USB data output for direct connection to PCs, data loggers or PLCs, and the colour touchscreen simplifies configuration for each interface. Is the caliper suitable for industrial environments? Built from stainless steel and rated IP54, the caliper withstands typical shop‑floor conditions such as dust and splashes; its robust design suits production and inspection areas. Does the built‑in design require special mounting? The built‑in format is intended for panel or machine integration; appropriate support along the beam is recommended for long‑range measurements to preserve stiffness and reproducibility. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
1500mm Built-In Digital Caliper Colour 2.4" Touchscreen, USB/Wireless, ISO 17025 Calibrated - Microtech Metrology
The combination of a 1,500 mm measuring range, ISO 17025 calibration and wireless data transfer ensures reliable, traceable results for large-scale inspection tasks; the aluminium construction keeps the instrument lightweight for installation and handling. Order the built-in caliper directly via Metav Werkzeuge or ask our consultants if needed. Built-in caliper — Digital caliper with 1,500 mm range and colour touchscreen (Microtech Metrology) A built-in caliper designed for long-range workshop and production measurements, offering wireless and USB data transfer plus an ISO 17025 calibration certificate for traceable results 1,500 mm measuring range Colour 2.4" touchscreen display Wireless and USB data output ISO 17025 calibration certificate included Reliable long-range measurement for large components The instrument addresses the demands of larger assemblies by providing a 1,500 mm measuring span that is classified in the Long category (1,000–2,000 mm), where profile stiffness and repeatability become decisive. The design balances reach and rigidity so that measurements across longer jaws remain reproducible; this is particularly relevant for fixture construction, housings and machine components that require consistent dimensional control over an extended length. The aluminium construction contributes to manageable weight without sacrificing stability. High-resolution digital readout and seamless data capture Equipped with a 2.4" colour touchscreen and a display resolution of 0.001 mm, the device delivers fine graduated readouts suitable for precise workshop checks and production spot checks. The dual data interfaces (wireless and USB) permit straightforward connection to logging systems or inspection software, reducing transcription errors and speeding up quality-control cycles. The touchscreen simplifies mode selection and unit changes, while the high display clarity supports fast, unambiguous readings on the shop floor. Traceable calibration and practical inspection accessories The instrument is supplied fully calibrated under ISO 17025, and a calibration certificate is included to document traceability for internal audits and supplier acceptance. This formal proof of calibration supports quality management processes and reduces the need for immediate external verification. An HD microscope with 7" LED display is provided as part of the scope, enabling magnified visual inspection of fine features next to dimensional checks and easing correlation between optical inspection and metrological results. Robust design adapted to industrial workflows Constructed from aluminium for a favourable strength-to-weight ratio, the caliper is suitable for integration where a built-in measuring solution is required. The combination of solid mechanical guidance and a digital transducer offers a dependable measuring chain for production environments. The instrument’s data outputs and calibration pedigree make it suitable for shop-floor traceability and integration into existing quality-control procedures, while the included inspection accessory supports multi-faceted assessment of parts. Discuss project requirements with Metav Werkzeuge — technical consultation and ISO 17025 documentation are available via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 142515158 GTIN: 4061905036910 Manufacturer: Microtech Metrology ISO 17025 calibration: included Facts Measuring range: 0–1500 mm Resolution / display increment: 0.001 mm Display: Colour 2.4" touchscreen Data output: Wireless + USB Special features Digital built-in caliper for long-range measurement HD microscope with 7" LED display included Aluminium construction ISO 17025 calibration certificate supplied FAQ What is the maximum measuring range of the caliper and how is it classified? The built-in caliper offers a measuring range of 0–1500 mm and is classified in the Long category (1,000–2,000 mm), making it suitable for larger fixtures, housings and assembly components. What accuracy and resolution can be expected from this instrument? The caliper provides a display resolution of 0.001 mm; the supplied ISO 17025 calibration confirms traceable performance for documented quality-control use. How can measurement data be exported from the device? Measurement data can be transferred via wireless connection or USB, enabling integration with inspection software and data-collection systems for streamlined logging and analysis. Is any additional equipment included for inspection tasks? An HD microscope with 7" LED display is included, allowing visual inspection alongside dimensional checks to support comprehensive part evaluation. Who manufactures this instrument and what documentation is provided? The instrument is supplied by Microtech Metrology and comes with an ISO 17025 calibration certificate and traceability documentation; the SKU is 142515158 for order and reference. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
1500mm Built-In Digital Caliper With 10x Magnifier, IP67 - Microtech Metrology
Take advantage of the combination of long-range capability, industrial ingress protection and fine display resolution for predictable, integration-ready measuring in production environments. Order the device directly via Metav Werkzeuge or consult our specialists for system integration and mounting advice. Built-in digital caliper — flush-mount design, 0–1500 mm, IP67 (Microtech Metrology) Built-in digital caliper for machine integration and long-range dimensional control within production and assembly systems. Digital display with Swiss Electronics module IP67 protection for dust and water resistance 0–1500 mm measuring range 10x magnification lens for clear reading Long-range precision engineered for large components The unit is designed for reliable measurement across an extended span, classified as a long-range caliper suitable for applications up to 0–1500 mm. The geometry and installation-ready form factor reduce handling time during in-line inspections and minimise deflection effects commonly encountered with longer measuring axes. With a resolution of 0.001 mm and a stated accuracy of ±0.04 mm, the instrument offers a useful combination of fine reading capability and practical repeatability for machine shops, fixture set-ups and component assembly tasks. Where absolute micrometre-level traceability is not required, this balance improves throughput without sacrificing verifiable dimensional control. Industrial-ready mounting and readable output for automated processes The flush-mount construction simplifies integration into fixtures and machines, while the Swiss Electronics display module provides a clear digital readout intended for both manual checks and signal interfacing. Rated IP67, the device withstands coolant spray and workshop dust, reducing downtime related to environmental exposure. The integrated 10x magnifier enhances visual verification of the scale and readout during setup and maintenance, which aids fast decision-making at the production line. These design choices support automation-friendly workflows by combining robustness with easily interpreted measurement data. Practical benefits for quality control and process stability Engineered for repeated use in production, the caliper supports consistent measurement routines that feed into quality assurance steps. The long span capability reduces the need for multiple gauge changes on larger parts, saving set-up time and lowering cumulative measurement uncertainty across an inspection sequence. The device’s combination of high resolution and durable construction helps maintain process stability: fewer interruptions for cleaning or repairs and clearer results for documentable inspections. For integrators and quality engineers, this translates into measurable gains in efficiency and fewer rejected batches due to measurement variability. Contact Metav Werkzeuge today for integration guidance and secure the Microtech Metrology built-in digital caliper (SKU 142515151) for robust, long-range measurement in production environments Technical data Article number: 142515151 GTIN: 4061905457906 Brand: Microtech Metrology Category: Digital caliper (built-in) Display: Swiss Electronics Core data Measuring range: 0–1500 mm Resolution: 0.001 mm Accuracy: ±0.04 mm Magnification: 10× Protection class: IP67 Special features Flush-mount construction for machine integration Digital output, integration-capable display Robust design for workshop and industrial environments Suitable for long-span component measurement FAQ How is the caliper suited to measuring large components? The built-in digital caliper provides a measuring range of 0–1500 mm, offering extended reach for large fixtures and assemblies while its design reduces deflection over long spans. What reading precision and overall accuracy can be expected? Resolution is 0.001 mm for fine readout increments; the declared system accuracy is ±0.04 mm, which defines the practical tolerance for production checks. Is the device protected against coolant and dust in workshop environments? Yes, the instrument is rated IP67, making it resistant to dust ingress and temporary immersion, suitable for many industrial conditions. Can the display be read easily during machine integration? The unit uses a Swiss Electronics display and includes a 10× magnifying lens for clear visual checks; the display is also suitable for electrical interfacing where required. Is the product suitable for automated inspection systems? The flush-mount design and digital output make the caliper well suited to integration into automated inspection or in-line control systems. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
1500mm Digitaler Einbauschieber, 0,01mm Auflösung, IP 67 - Microtech Metrology
Die robuste Kombination aus Einbaumessschieber, grossem Messbereich und digitaler Anzeige sorgt für reproduzierbare Messwerte auch bei langen Bauteilen. Nutzen Sie die hohe Schutzart und die praxistaugliche Ablesung für effiziente Prüfabläufe. Bestellen Sie den Einbaumessschieber direkt über Metav Werkzeuge oder fragen Sie unsere Beratung bei Bedarf an. Einbaumessschieber von Microtech Metrology Der Einbaumessschieber ist ein digitales Messgerät für präzise Längenmessungen an grossen Bauteilen und eignet sich besonders für die Integration in Prüfplätze und Fertigungsstationen. Digitale Big‑Screen‑Anzeige für schnelle Ablesung IP 67 Schutzklasse für raue Fertigungsumgebung Messbereich 0–1500 mm für lange Werkstücke Auflösung 0,01 mm für klar definierte Ergebnisse Geeignet für Labor und Produktionslinie Hohe Reichweite für große Bauteile und Vorrichtungen Der Messschieber bietet einen Messbereich von 0–1500 mm, was ihn in die Kategorie Lang einordnet und ideal für die Kontrolle grösserer Spannmittel, Aufnahmen und Gehäuse macht. Diese Reichweite ermöglicht es, lange Werkstücke mit einem Gerät zu überprüfen, wodurch Umlenkungen und Transportwege reduziert werden. Anwender profitieren von weniger Rüstzeit und höheren Durchsatzraten bei der Serienprüfung. Schutz und Robustheit für den Einsatz in der Produktion Dank der Schutzart IP 67 bleibt die Elektronik geschützt gegen Staub und zeitweiliges Untertauchen, sodass der Messschieber direkt an Fertigungsplätzen und in feuchten Umgebungen eingesetzt werden kann. Die robuste Bauweise erhöht die Lebensdauer des Geräts und reduziert Stillstandszeiten, was die Gesamtbetriebskosten senkt. Ein einfaches Handling sorgt dafür, dass Prüfzyklen zuverlässig abgeschlossen werden. Präzision und Ablesbarkeit für reproduzierbare Ergebnisse Die Anzeige liefert eine Ablesung von 0,01 mm, ergänzt durch eine Genauigkeit von 0,07 mm, und ermöglicht so verlässliche Messungen im Produktionsalltag. Die grosse digitale Anzeige "Big Screen Swiss Electronics" vereinfacht das Erfassen der Werte, reduziert Ablesefehler und beschleunigt die Prüfprotokollierung. Diese Kombination unterstützt die Einhaltung von Fertigungstoleranzen ohne aufwändige Zusatzmessmittel. Integration in Prüfabläufe und Prozesssicherheit Das digitale Design erlaubt die einfache Einbindung in laufende Prüfprozesse; die direkte Ablesung fördert schnelle Entscheidungen bei der Qualitätskontrolle. Durch die kompakte Bauform lässt sich das Messgerät in Prüfstände einbauen, was Wiederholbarkeit und Messstabilität erhöht. Anwender in Fertigung und Qualitätssicherung erhalten so eine Lösung, die den Prüfablauf vereinfacht und messbare Effizienzgewinne bringt. Setzen Sie auf den Einbaumessschieber von Microtech Metrology und sichern Sie sich reproduzierbare Langmessungen für Ihre Fertigung — bestellen Sie dieses Messinstrument bequem über Metav Werkzeuge; bei Fragen steht das Metav‑Team per E‑Mail und Telefon zur Verfügung. Technische Daten Artikelnummer: 142515147 Marke: Microtech Metrology Bezeichnung: Einbaumessschieber GTIN: 4061905459740 Fakten Messbereich: 0–1500 mm Ablesung: 0,01 mm Genauigkeit: 0,07 mm Besonderheiten IP 67 Schutz Digitale Anzeige: Big Screen Swiss Electronics Digital ECLASS: 21170344 FAQ Wie gross ist der Messbereich dieses Messschiebers? Der Messschieber von Microtech Metrology deckt einen Messbereich von 0–1500 mm ab und eignet sich damit für Messaufgaben im Langbereich. Welche Auflösung und Genauigkeit bietet das Gerät? Das Gerät liefert eine Ablesung von 0,01 mm; die angegebene Genauigkeit beträgt 0,07 mm, was eine zuverlässige Messung im Fertigungsumfeld ermöglicht. Ist das Gerät für nasse oder staubige Umgebungen geeignet? Ja, der Einbaumessschieber verfügt über die Schutzklasse IP 67, sodass er gegen Staub und zeitweiliges Untertauchen geschützt ist und sich für raue Umgebungen eignet. Eignet sich der Messschieber für die Integration in Prüfstände? Der Einbaumessschieber von Microtech Metrology wurde für die Einbaumontage konzipiert und lässt sich in Prüfplätze und Fertigungsstationen integrieren, um wiederholbare Messungen zu gewährleisten. Welche Anzeige kommt zum Einsatz? Verwendet wird die digitale Anzeige "Big Screen Swiss Electronics", die eine gute Lesbarkeit und schnelle Erfassung der Messwerte erlaubt. Hersteller: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine; tool@microtech.tools
1500mm Einbaumessschieber, 0,001mm Ablesung, IP 67, Swiss Electronics - Microtech Metrology
Die Kombination aus großem Messbereich und feiner Ablesung sorgt für reproduzierbare Messergebnisse, während die IP 67 Schutzart den Einbau auch in rauen Produktionsumgebungen erlaubt. Nutzen Sie die hohe Reichweite und die robuste Bauweise für seriennahe Messprozesse und bestellen Sie den Einbaumessschieber direkt über Metav Werkzeuge oder fordern Sie technische Beratung an. Einbaumessschieber von Microtech Metrology Der Einbaumessschieber von Microtech Metrology eignet sich für präzise Längenmessungen im Einbau bis 1500 mm und für anspruchsvolle industrielle Anwendungen. Einbaumessschieber von Microtech Metrology Messbereich bis 1500 mm für Langmessungen Ablesung 0,001 mm für feine Details IP 67 Schutzart für rauen Einsatz Swiss Electronics Display mit digitaler Anzeige Robuste Konstruktion für industrielle Einbaulösungen Die mechanische Ausführung des Einbaumessschiebers wurde für den Dauerbetrieb konzipiert und bietet eine belastbare Bauart, die Vibrationen und wiederholte Belastungen standhält. Durch die geschützte Elektronik und die IP 67 Klassifizierung bleibt die Funktionalität auch bei Staubbelastung und kurzzeitigem Untertauchen erhalten, was Einbauorten mit Spritzwasser oder Emulsionen entgegenkommt. Das stabile Profil minimiert Durchbiegung über lange Messlängen und erhöht die Messreproduzierbarkeit. Präzision und Ablesegenauigkeit für verlässliche Messwerte Dank einer feinen Ablesung von 0,001 mm lassen sich auch kleine Maßabweichungen sicher erkennen; die deklarierte Genauigkeit von 0,04 mm gibt die erwartbare Messunsicherheit über den gesamten Messbereich an. Diese Kombination macht den Schieber geeignet für Fertigungsprüfungen, Qualitätskontrolle und Vorabmessungen bei Montagearbeiten. Die digitale Anzeige erleichtert die schnelle Dokumentation und reduziert Ablesefehler gegenüber rein mechanischen Lösungen. Einbau, Integration und Bedienkomfort Beim Einbau bietet die kompakte Messkopfgeometrie einfache Montagemöglichkeiten in Vorrichtungen und Messstationen. Die digitale Swiss Electronics Anzeige ist auf schnelle Lesbarkeit ausgelegt und ermöglicht eine zügige Anbindung an Auswerteeinheiten, sofern Schnittstellen vorhanden sind. Für Anwender bedeutet das weniger Ausfallzeiten und eine höhere Taktung bei wiederkehrenden Prüfzyklen, da Messvorgänge schneller und sicherer ablaufen. Zielgruppe und typische Einsatzfelder Konstruktionsbüros, Werkstätten und Fertigungsstraßen profitieren von der großen Messlänge und der robusten Schutzart, die den Einbaumessschieber zu einem Werkzeug für Serienmessungen und langlebige Prüfplätze macht. Besonders geeignet ist das Gerät dort, wo längere Bauteile direkt in der Maschine oder Vorrichtung vermessen werden müssen. Anwender mit Ansprüchen an Reichweite und praktikable Handhabung finden hier eine ausbalancierte Lösung. Empfehlung: Für präzise Langmessungen im Einbau wählen Sie den Einbaumessschieber von Microtech Metrology und nutzen Sie die Verfügbarkeit und Beratung von Metav Werkzeuge per E‑Mail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 Produktmerkmale Artikelnummer: 142515146 GTIN: 4061905459962 Marke: Microtech Metrology Bezeichnung: Einbaumessschieber Digitalanzeige: Swiss Electronics Fakten Genauigkeit: 0,04 mm Ablesung: 0,001 mm Messbereich: 0–1500 mm IP-Schutz: IP 67 Besonderheiten Digitales Messgerät Swiss Electronics Display IP 67: staubdicht, kurzzeitiges Untertauchen Messschieber-Kategorie: Lang (Messbereich 1000–2000 mm) FAQ Wie groß ist der Messbereich dieses Messschiebers? Der Messschieber von Microtech Metrology bietet einen Messbereich von 0–1500 mm und eignet sich damit für Langmessungen in Fertigungs- und Einbausituationen. Welche Auflösung und Genauigkeit liefert das Gerät? Die Ablesung beträgt 0,001 mm bei einer angegebenen Genauigkeit von 0,04 mm, wodurch feine Maßabweichungen erkennbar und reproduzierbar werden. Ist das Messgerät für den Einsatz in feuchten Umgebungen geeignet? Durch die Schutzart IP 67 ist der Einbaumessschieber gegen Eindringen von Staub geschützt und hält kurzzeitiges Untertauchen stand, somit ist ein Einsatz in feuchteren Fertigungsbereichen möglich. Eignet sich der Schieber für die Qualitätskontrolle in der Serienfertigung? Ja, der große Messbereich kombiniert mit der feinen Ablesung macht den Einbaumessschieber von Microtech Metrology zum geeigneten Messmittel für wiederkehrende Prüfungen in der Serienfertigung. Welche Anzeige-Technik wird verwendet? Der Schieber ist mit einer digitalen Anzeige von Swiss Electronics ausgestattet, die eine klare Darstellung der Messwerte ermöglicht und die Erfassung beschleunigt. Hersteller: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine; tool@microtech.tools
150mm Built-In Digital Caliper Colour Touchscreen, IP54, ISO 17025 Calibrated - Microtech Metrology
Take advantage of precise 0.01 mm measurement, rugged stainless-steel construction and integrated Wireless + USB data transfer for reliable inline measurement and traceable results; order the built-in digital caliper directly via Metav Werkzeuge or consult our advisors for integration support. Built-in digital caliper — Microtech Metrology, Colour 1.54" Touchscreen, Wireless + USB Built-in digital caliper designed for panel integration and inline quality checks in production and R&D environments Integrated colour 1.54" touchscreen display Wireless and USB data output Robust stainless-steel construction ISO 17025 calibrated with certificate Precision that supports production decisions The integrated caliper delivers a 0.01 mm accuracy level suited to standard workshop and machine‑tool quality control. Calibrated to ISO 17025, the tool is supplied with a calibration certificate, enabling immediate use in documented inspection processes and assuring traceability. The standard measuring range (0–150 mm) strikes a balance between reach and rigidity, making the instrument suitable for component inspection, setting tasks and comparative part checks. Where routine measurement must be reproducible, the embedded microcomputer and clear touchscreen reduce operator ambiguity and contribute directly to faster, comparable results on the shop floor. Seamless data flow for faster inspection cycles Equipped with both Wireless and USB outputs and a Colour 1.54" touchscreen, the device simplifies data capture and transfer to inspection software or SPC systems. The panel‑mount design allows direct installation into test fixtures or machine-control panels, removing the need for temporary fixturing and lowering cycle times. With IP54 protection, the electronics tolerate dust and splashing typical of many workshops, helping keep inspection running even in less-than-ideal conditions. The combination of embedded control, intuitive display and reliable interfaces reduces manual transcription errors and accelerates decision-making in production control. Durable construction tailored to everyday use Constructed from stainless steel, the caliper tolerates regular handling and resists corrosion in mixed workshop environments. Its form factor—designed for built‑in mounting—keeps moving parts protected and ensures stable alignment during repeated measurements. Classified in the standard range category, it benefits from a compromise of stiffness and reach that aids single‑handed operation and mounting stability. The instrument’s robust build and factory calibration mean fewer rechecks, lower measurement uncertainty and improved uptime, supporting both small repair shops and larger production lines that require dependable metrology tools. For reliable integration and certified calibration of the Microtech Metrology built-in digital caliper, contact Metav Werkzeuge to discuss application requirements and mounting options — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: 142501140 GTIN: 4061905036989 Brand: Microtech Metrology Measuring range: 0–150 mm Display: Colour 1.54" touchscreen Data output: Wireless + USB Protection class: IP 54 Material: stainless steel Digital: yes Calibration: ISO 17025 certificate included Facts Measuring range: 0–150 mm Resolution / display: 0.01 mm Accuracy: 0.01 mm Special features Integrated microcomputer for embedded use Colour 1.54" touchscreen Wireless communication and USB interface ISO 17025 calibrated with certificate Robust stainless-steel construction IP54 splash and dust protection FAQ Is the calibration traceable and included with delivery? Yes. The built-in digital caliper from Microtech Metrology is supplied fully calibrated with an ISO 17025 calibration certificate included. Can measurement data be recorded automatically? Measurement values can be exported via Wireless or USB interfaces for automatic logging into inspection software or SPC systems. What is the usable measuring range and typical applications? The caliper covers 0–150 mm, a standard workshop range suitable for component inspection, set‑up tasks and general quality control. Is the device suitable for the production environment? With stainless-steel construction and IP54 protection, the instrument is designed to withstand typical workshop conditions and frequent handling. Can the unit be mounted into a control panel or fixture? The built-in design includes an integrated microcomputer intended for panel or fixture installation, enabling direct integration into measurement stations. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
150mm Digital Built-In Caliper, Vertical Stainless Steel, Bidirectional Measurement, DIN 862 - Metav IndustryLine
Take advantage of high-resolution capacitive measurement and DIN 862 conformity to streamline in-line QC; the compact built-in design and bidirectional reading reduce cycle time and handling errors. Order the device directly via Metav Werkzeuge or consult the specialists for mounting and data-integration advice. Digital built-in caliper M218.254 — 150 mm, capacitive measuring system, 0.01 mm resolution Digital built-in caliper M218.254 is a DIN 862-compliant measuring module for workshop panels and machine interfaces, designed for vertical installation where robust, repeatable linear measurement is required Capacitive measuring system, 0.01 mm resolution 150 mm measuring range, DIN 862 compliant Bidirectional measurement capability Integrated mm/inch, zero and hold functions Reliable precision for workshop quality control The built-in caliper uses a capacitive measuring system with an electronic display resolution of 0.01 mm, delivering fast, numerical results suitable for statistical process control. The declared measuring uncertainty of ±0.03 mm defines its suitability for standard workshop inspection tasks where consistent repeatability is required. Compliance with DIN 862 provides a familiar reference for machinists and inspection personnel, ensuring the module integrates into established calibration and QA routines while reducing interpretation errors from analogue readouts. Space-saving mounting and practical operation features Designed as a vertical, built-in unit in a stainless steel housing, the device fits into machine doors, test fixtures or bespoke control panels without occupying bench space. The digital display offers a clear button set (ON/OFF/PRE-, mm/inch, 0/ABS-, TOL, DIR and HOLD) to simplify measurements and setup. The RB 5 data output enables connection to data loggers or readout systems, facilitating automated capture of measurement results and eliminating manual transcription steps that introduce errors into production logs. Application scope and handling benefits Classified in the Standard (100–300 mm) range, the caliper combines reach and rigidity for everyday applications in metalworking, toolmaking and component assembly. The bidirectional measurement function allows readings when the slide is moved in either direction, reducing handling time for repetitive checks. At approximately 0.45 kg, the unit is compact yet robust, making it suitable for permanent installation in jigs or as a fixed reference in production cells where quick, repeatable checks are required to maintain throughput and reduce scrap rates. For precision mounting and integration assistance with the Metav IndustryLine digital built-in caliper, contact Metav Werkzeuge for tailored advice on panel cut-outs, data cabling and calibration options — Metav Werkzeuge provides local stocking and technical support from Emmerich to streamline deployment. Technical Data Article number: M218.254 GTIN: 4054469111858 Manufacturer: Metav IndustryLine Norm: DIN 862 Facts Measuring range: 0–150 mm Display resolution: 0.01 mm Readout (inch): 0.0005 in Declared accuracy: ±0.03 mm Weight: 0.45 kg Tariff number: 90173000 Special features Capacitive measuring system Built-in vertical mounting, stainless steel housing Digital display with ON/OFF/PRE-, mm/inch-, 0/ABS-, TOL-, DIR-, HOLD buttons Bidirectional measurement capability Data output: RB 5 Digital implementation for panel or fixture integration FAQ Is this caliper suitable for panel mounting in a production machine? The caliper M218.254 is designed for built-in, vertical mounting and is suitable for installation in machine panels or jigs where a compact, repeatable measuring station is required. What level of accuracy can be expected in routine checks? The device provides a display resolution of 0.01 mm with a declared measuring uncertainty of ±0.03 mm, which is appropriate for standard workshop quality control tasks. Can the output be recorded automatically? Yes, the unit offers an RB 5 data output that allows integration with data loggers or PLCs to support automated result capture and process documentation. Which measurement modes are available on the display? The display includes mm/inch selection, absolute/relative zero setting (0/ABS), tolerance (TOL) indication, directional (DIR) and hold (HOLD) functions for flexible measurement workflows. Is the caliper corrosion-resistant for industrial environments? The built-in module is specified as stainless, which provides improved resistance to workplace atmospheres; final environmental suitability depends on the specific exposure conditions and enclosure installation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
150mm Digital Einbaumessschieber waagerecht, 0,01mm, DIN 862 - Metav IndustryLine
Der 1989 gegründete Traditionsvertrieb von Messwerkzeugen steht mit seiner Eigenmarke Metav IndustryLine für Premium-Messwerkzeuge zu einem überzeugenden Preis. Das wichtigste auf einen Blick waagerecht Messbereich: bis 150mm Ablesung: 0,01mm Material: Messschiene aus Aluminium (30x7,9mm) Ausführung: digital Datenausgang: RB 5 MESSBEREICH} mm – von der Vorbereitung bis zur Freigabe Der Messbereich 0 – 150mm bringt die nötige Reichweite für typische Bauteile auf den Punkt. Prüfungen gelingen direkt am Werkstück, auch wenn Formen variieren. Im allgemeinen Maschinen- und Metallbau sorgt dieser Bereich für eine sichere Orientierung über den gesamten Prozess. Die Ergebnisse bleiben nachvollziehbar und konsistent. Das reduziert Nacharbeit und unterstützt saubere Übergaben zwischen Arbeitsschritten. Unsere Definition der EInteilung der Messbereiche. Klassifizierung Messbereiche beim Messschieber.. Gefertigt nach DIN 862 Unser Messwerkzeug wird streng nach DIN 862 gefertigt. Alle Materialien, Herstellungs- und Kalibrierverfahren entsprechen dieser Norm. So stellen wir Maßhaltigkeit, Wiederholgenauigkeit und internationale Vergleichbarkeit sicher. DIN-konforme Prüfzertifikate erleichtern Audits, beschleunigen Freigaben und gewährleisten eine konstante Qualität weltweit. Die Premium Messwerkzeuge von Metav IndustryLine werden von unseren Profis für Messwerkzeuge empfohlen. Metav IndustryLine steht für Premium Messwerkzeuge zu einem unschlagbaren Preis. Alle Messwerkzeuge werden nach der Produktion gestestet. Sie wissen nicht genau, ob dieses Werkzeug zu Ihrer Anwendung passt? Oder Ihnen fehlen noch wichtige technische Details? Kein Problem! Kontaktieren Sie uns – wir beraten Sie gerne. 📧 eMail: info@metav-werkzeuge.com ✔️ WhatsApp: +49 170 2837271 ☎️ Telefon: +49 2822 7131930 Technische Daten: Marke: Metav IndustryLine Bezeichnung: Einbaumessschieber Bestellnummer: M218.354 Zahlen / Fakten: Messbereich: 0-150mm Gewicht: 0,25kg Norm: DIN 862 Ablesung: 0,01mm Datenausgang: RB 5 Ablesung in Inch/Zoll: 0,0005 Genauigkeit: 0,03mm Länge: 280mm Besonderheiten Ausführung: digital Material: Messschiene aus Aluminium (30x7,9mm) Anzeige: mit EIN/AUS-, mm/inch- und NULL-Taste Messsystem: kapazitiv waagerecht Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; www.metav-shop.de; info@metav-werkzeuge.com Zu beachtende Faktoren beim Erwerb eines Messschiebers: Die zusätzliche Ausstattung, darunter Datenausgänge und Messkraftkontrollen, erlangt neben der Genauigkeit und dem Messbereich erhebliche Bedeutung. Der Einsatz eines Messschiebers mit kontrollierter Messkraft ist besonders in der Qualitätssicherung und in Laborumgebungen vorteilhaft. Außerdem sollte man untersuchen, ob ein kalibrierter Messschieber sinnvoll ist. Man kann die Kalibrierung bei Lieferung vornehmen und aus Gründen der Prozesskontinuität alle 12 Monate erneuern. Pflegehinweis - damit Sie lange etwas von Ihrem Einbaumessschieber von Metav IndustryLine haben: Einbaumessschieber leben viele Jahrzehnte, wenn du sie sauber, leicht eingeölt, korrekt gelagert und regelmäßig geprüft hälst. Vermeide aggressive Lösungsmittel oder dicke Ölschichten, wische nach jedem Einsatz mit einem fusselfreien Tuch nach, schütze die Führungen mit einem Mikrofilm aus Instrumentenöl (z. B. Starrett M-1), lagere das Werkzeug trocken in seinem Etui mit leicht geöffneten Messflächen – am besten mit einem Silicagel-Beutel – und überprüfe Nullpunkt, Messflächen und Gleitspiel nach ISO-Temperaturnorm (20 °C).
150mm Digital Precision Caliper Horizontal Mount Small Housing Stainless Steel DIN 862 - Metav IndustryLine
Take advantage of a compact 150 mm digital inset caliper that combines hardened stainless-steel construction with a 0.01 mm display resolution and DIN 862 conformity for dependable workshop measurement; order the instrument directly via Metav Werkzeuge or consult our technical advisors for integration support. M218.154.N Digital inset caliper — 150 mm, stainless hardened (Metav IndustryLine) The M218.154.N is a compact 150 mm digital inset caliper for horizontal installation, designed for standard workshop and production measurement tasks under the DIN 862 norm. Compact 150 mm measuring range Digital display 0.01 mm resolution Hardened stainless-steel construction DIN 862 conformity, small housing Precise measurement where repeatability matters The inset caliper delivers a clear 0.01 mm readout with an indicated accuracy of ±0.03 mm, which supports routine quality controls and machining checks with measurable reproducibility. The electronic display is equipped with ON/OFF, ZERO, UNIT and HOLD functions to speed up tasks and reduce transcription errors; the unit also provides inch readings at 0.0005 in resolution for mixed-measurement workflows. These characteristics make the instrument a practical choice for environments that prioritise reliable numeric data and traceable measurement steps. Space-saving design that keeps installation simple Built with a small housing and intended for horizontal mounting, this caliper fits into constrained mounting positions without sacrificing measuring face stiffness. With a 150 mm measuring range the tool sits in the Standard category of calipers (max. range 100–300 mm), which is the workshop default for a balance of reach, rigidity and one-handed handling. The compact format is particularly suitable for machine-tool fixtures, jigs and small-batch inspection stations where space and repeatability are equally important. Robust materials and straightforward operation Constructed from hardened stainless steel, the device resists wear and corrosion in demanding shop-floor conditions while maintaining jaw geometry for consistent readings. Power is supplied by a 3 V cell for long service life and simple replacement. For data capture and process documentation the unit includes a RB 5 data output interface, allowing digital transfer of measured values into external systems or data loggers. The solid material choice and electronic readout reduce the need for repeated manual rechecks, improving throughput in serial inspection tasks. How this caliper supports production workflows As a digital inset caliper engineered to DIN 862, it bridges bench measurement and inline control: faster readings, less interpretation, and direct digital logging where required. The combination of a hardened slide, compact housing and clear display translates into fewer measurement-related stoppages and smoother quality routines. For buyers seeking a pragmatic instrument that integrates into standard metrology procedures, this format reduces the friction between workshop reality and formal inspection criteria. For precise workshop measurement and easy integration, contact Metav Werkzeuge for technical advice or purchasing information — Metav IndustryLine instruments are distributed from Emmerich; email info@metav-werkzeuge.com or call +49 2822 7131930 for further assistance. Technical data Article number: M218.154.N GTIN: 4054469160740 ECLASS: 21170344 Type: Digital inset caliper Weight: 0.3 kg Measuring range: 0–150 mm Resolution: 0.01 mm / 0.0005 in Accuracy: ±0.03 mm Material: hardened stainless steel Norm: DIN 862 Power: 3 V measuring system Display: ON/OFF, ZERO, UNIT, HOLD Data output: RB 5 Digital: yes FAQ What resolution does the caliper provide? The caliper shows 0.01 mm resolution on the digital display (0.0005 in) for detailed dimensional checks. What accuracy can be expected during measurement? The device specifies an accuracy of ±0.03 mm, suitable for standard workshop quality control and machining tolerances. Is the instrument suitable for machine-shop use? Yes — with its 150 mm range and hardened stainless-steel construction the caliper is in the Standard class, designed for everyday use in machine and metalworking environments. Which data interface is available for digital logging? The caliper features an RB 5 data output to facilitate transfer of readings to external recording devices. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
150mm Precision Digital Caliper Colour Touchscreen, IP54, ISO 17025 Calibrated - Microtech Metrology
Benefit from traceable, workshop-ready measurement: ISO 17025 calibration with certificate, ±0.008 mm accuracy and wireless data transfer for faster logging; order the instrument directly via Metav Werkzeuge or consult our specialists for integration advice. Built‑in digital caliper – Microcomputer control, IP54 protection and 1.54" colour touchscreen (Microtech Metrology) The Built‑in digital caliper is a compact, workshop‑grade measuring instrument designed for standard machinist and quality‑control tasks with a measuring range of 0–150 mm. Colour 1.54" touchscreen display Wireless and USB data output High accuracy ±0.008 mm Stainless steel construction, IP54 Precise, certified measurements that fit everyday inspection The instrument delivers a high level of measurement certainty thanks to a resolution 0.001 mm and accuracy ±0.008 mm, making it suitable for demanding production checks. Classified as Standard range (measuring range 0–150 mm), this caliper offers the balance between reach and rigidity that most workshop routines require. Delivered fully calibrated, the device includes an ISO 17025 calibration certificate, extending traceability and simplifying quality documentation for audit‑ready production. Faster data flow and fewer transcription errors Equipped with Wireless and USB data outputs and a colour 1.54" touchscreen, the caliper supports direct digital capture and quick inspection reporting. Integration into digital logs or SPC workflows reduces manual entry and speeds up routine checks—an efficiency gain that lowers cycle times and improves traceability. The touchscreen interface simplifies configuration and readout, while the combined data ports ensure compatibility with a wide range of measurement systems. Robust build for the workshop environment Constructed from stainless steel and rated IP54, the unit resists dust and splashes common in production areas and is built for repeated handling. The built‑in design is suitable for integration into measurement fixtures or compact stations where a flush or embedded installation is preferred. This durability, together with the practical protection rating, reduces downtime and preserves calibration intervals, helping maintain consistent measurement results over time. Contact Metav Werkzeuge for technical integration support and to request the full technical datasheet for the Microtech Metrology built‑in digital caliper (Article No. 142501141) with ISO 17025 calibration Technical Data Article number: 142501141 GTIN: 4061905036996 Brand: Microtech Metrology Display: Colour 1.54" touchscreen Data output: Wireless + USB Measuring range: 0–150 mm Material: stainless steel Calibration: ISO 17025 certificate included Protection: IP54 Facts Accuracy: ±0.008 mm Resolution: 0.001 mm Measuring range: 0–150 mm Display size: 1.54" Protection class: IP54 Special features Built‑in design for integration Colour touchscreen interface Wireless and USB data output Stainless steel construction Delivered calibrated to ISO 17025 FAQ Is the caliper supplied with a calibration certificate? Yes. The Microtech Metrology built‑in digital caliper (Article No. 142501141) is delivered fully calibrated and includes an ISO 17025 calibration certificate. What measuring range and accuracy does the instrument offer? The instrument covers 0–150 mm and provides an accuracy of ±0.008 mm with a resolution of 0.001 mm. How can measurement data be exported from the caliper? Measurement data can be transferred via Wireless or USB output, enabling direct logging into inspection software or data collection systems. Is the caliper suitable for everyday shop use? Yes. Its stainless steel construction and IP54 rating make the caliper robust against dust and splashes typically encountered in workshop environments. Can the unit be integrated into a measurement station or fixture? The built‑in design is intended for integration into fixtures and compact stations, allowing installation where a flush or embedded caliper is required. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
200 mm Digital Precision Caliper With Remote Display 0.01 mm Resolution, Steel Measuring Jaw, Magnetic Back - Metav IndustryLine
Take advantage of a precise absolute measuring system, a separate external display and a robust steel measuring rod to secure reliable workshop measurements and smoother integration into machine setups. Order the product directly via Metav Werkzeuge or ask our consultants if needed. Digital built-in caliper ABS 200 mm (separate display) — Metav IndustryLine A Digital built-in caliper ABS 200 mm for machine-embedded measurement tasks, offering a remote display and workshop-grade durability for everyday quality control. Separate external display for ergonomic reading Absolute measuring system with fast zero-set Resolution 0.01 mm and inch readout options Rear magnetic plate for secure mounting Precise, installation-ready measurement for standard workshop use The built-in caliper features an absolute measuring system that retains its zero position without homing after power cycles, delivering dependable repeatability in assembly and inspection tasks. With a resolution of 0.01 mm, the instrument supports typical workshop tolerances while the steel measuring rod ensures long-term dimensional stability under mechanical load. Classified in the Standard range (measurement range up to 100–300 mm), this model balances reach and stiffness for general machine‑shop applications such as part checking, fixture set‑up and incoming inspection. The remote display separates the readout from the measuring head, reducing handling and improving ergonomic access when the caliper is integrated into jigs or enclosures. Robust data handling and integration for efficient workflows Data transfer is provided via RB6 and Micro‑B outputs, enabling wired connection to data loggers, measuring stations or PLCs for traceable recording and statistical process control. The caliper’s display supports readings in mm, inch and fractions, simplifying cross‑unit documentation without manual conversion. Supplied with an approx. 2 m connection cable, the instrument can be installed close to control points while the display remains accessible. The combination of a fixed external indicator and standard interfaces reduces measurement steps and potential transcription errors, improving throughput in repetitive quality routines. Practical functions and mounting that reduce setup time Key practical functions such as presetting and hold for measurement values allow measurements to be stored and referenced during assembly or inspection tasks; the rear magnetic plate provides a reliable temporary attachment to ferrous fixtures during adjustment or calibration checks. Battery power is provided by two CR2032 cells, so the display retains local operation where bus power is not available. Compact handling, a clear digital readout and straightforward electrical outputs mean this caliper is suited to retrofit installations as well as new machine builds, giving workshop teams confidence in consistent, auditable measurement results. Contact Metav Werkzeuge to discuss application-specific integration or to place an order—call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: M218.275 GTIN: 4054469163895 Brand: Metav IndustryLine Facts Measurement range: 0–200 mm Resolution: 0.01 mm / 0.0005 in Accuracy: ±0.03 mm Weight: 0.45 kg Power supply: 2x CR2032 Cable length (included): approx. 2 m Special features Absolute measuring system Separate external display Preset and hold function Rear magnetic plate for mounting Steel measuring rod Readout in mm, inch and fractions Data output: RB6 and Micro‑B Supplied with connection cable FAQ What measurement range does this caliper cover? The caliper covers a measurement range of 0–200 mm, placing it in the Standard category suitable for general machine‑shop and metalworking tasks. Can the instrument output measurement data to a PC or PLC? Yes, the unit provides RB6 and Micro‑B interfaces for wired data transfer, enabling connection to data collection systems and process control equipment. Is the display able to show inches as well as millimetres? The separate indicator supports readings in mm, inch and fraction formats for flexible documentation and cross‑unit checks. Which power source does the remote display use? The display is powered by two CR2032 batteries; the package includes the connection cable for installing the display near the measuring head. What practical functions assist in workshop use? Features include presetting of measurement values and a hold function to stabilise readings; the caliper also has a rear magnetic plate for convenient temporary mounting. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2000mm Built-In Digital Caliper Color 2.4" Touchscreen, Wireless/USB, IP54, ISO 17025 Calibration - Microtech Metrology
Take advantage of the combination of long-range measurement capability, robust stainless steel construction and full ISO 17025 calibration for reliable, traceable results in demanding workshop and production environments. Order the instrument directly via Metav Werkzeuge or consult our technical team for application-specific advice. Built-in digital caliper — Microtech Metrology, 0–2000 mm, Colour 2.4" touchscreen The Built-in digital caliper is a panel-mountable, long-range measuring instrument designed for industrial metrology tasks where traceable calibration and straightforward data capture are required ISO 17025 calibrated with certificate included Colour 2.4" touchscreen display Wireless and USB data output Stainless steel body with IP54 protection Consistent accuracy for repeatable large-scale measurements The instrument offers a measurement range of 0–2000 mm combined with a display resolution of 0.01 mm and an indicated accuracy of ±0.06 mm, delivering a practical balance between reach and precision for large components. Because the unit is delivered fully ISO 17025 calibrated, a formal calibration certificate accompanies each device, which streamlines quality documentation and supports audit requirements. For production lines and workshop QC where repeatability over metres matters, this specification reduces rework and accelerates assembly checks. Streamlined data handling and integration into production systems Equipped with Wireless and USB data outputs plus a colour 2.4" touchscreen, the caliper simplifies transfer of measurement data to SPC systems or inspection software and removes error-prone manual transcription. The touchscreen provides fast on-device checks and configuration, while wireless connectivity enables remote logging and batch collection. The result is a measurable efficiency gain in inspection cycles and a lower administrative overhead for traceable measurement records. Robust design aimed at industrial use and long-range handling Constructed from stainless steel and rated IP54, the unit tolerates typical workshop contaminants while maintaining structural stiffness across its long slide. With a maximum range of 2000 mm, this device fits the "Long" caliper class (1,000–2,000 mm), which is optimised for larger assemblies where handling and profile stiffness are decisive for reproducible readings. The housing and slide geometry minimise deflection, so single-operator checks on medium-to-large fixtures remain practical and reliable. Practical applications and benefits in daily operations This measurement solution is suitable for large fixture checks, dimensional control of housings and assemblies, and in-process inspections where direct digital capture shortens the feedback loop. The included ISO 17025 calibration supports subcontracting and acceptance testing, while the rugged build and data interfaces encourage seamless integration into existing quality workflows. For workshops seeking to democratise precision without added supplier complexity, the combination of traceability and connectivity provides clear operational value. Choose Microtech Metrology's long-range built-in digital caliper with ISO 17025 calibration for dependable, traceable measurements — contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 for purchase support and technical advice Technical data SKU: 142520140 GTIN: 4061905036668 Manufacturer: Microtech Metrology Category: Digital caliper Display: Colour 2.4" touchscreen Data output: Wireless, USB Material: Stainless steel Protection rating: IP54 Delivered with ISO 17025 calibration certificate Facts Measurement range: 0–2000 mm Resolution (display): 0.01 mm Stated accuracy: ±0.06 mm Protection class: IP54 Special features Long-range caliper class (1,000–2,000 mm) Colour touchscreen interface Wireless and USB connectivity Delivered fully ISO 17025 calibrated Robust stainless steel construction FAQ Is the caliper supplied with an official calibration certificate? Yes. The caliper is supplied fully calibrated under ISO 17025 and includes the calibration certificate for traceability and quality records. What interfaces are available for data transfer? Data transfer is handled via Wireless and USB outputs, allowing straightforward connection to inspection software and SPC systems. What is the effective measurement range and which application class does it fit? The unit covers 0–2000 mm and is classified in the long-range caliper class (1,000–2,000 mm), suitable for larger assemblies and fixtures. How durable is the device in workshop conditions? With a stainless steel body and IP54 protection rating, the instrument resists dust ingress and splashes found in typical workshop environments. What resolution and accuracy can be expected from readings? The display resolution is 0.01 mm, with a stated accuracy of ±0.06 mm, which supports reliable dimensional checks across the full measuring range. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
2000mm Built-In Digital Caliper Colour 2.4" Touchscreen, Wireless/USB, ISO 17025 Calibrated HD Microscope Included - Microtech Metrology
Take advantage of the combination of long-range capability, sub-micron reading resolution and ISO 17025 traceable calibration for reproducible measurements on large components; order the instrument directly via Metav Werkzeuge or consult the technical team for integration advice. Built-in digital caliper — long-range 0–2000 mm with colour touchscreen (Microtech Metrology) The Built-in digital caliper is a long-range measurement solution for workshop and fixture applications, designed to deliver high-resolution readings and straightforward data transfer for production and quality‑control environments. Long-range measuring up to 2,000 mm Colour 2.4-inch touchscreen Wireless and USB data output Delivered calibrated to ISO 17025 Precision across long spans for larger components For applications that require reliable measurements over long distances, this instrument is classified as a long-range caliper with a measuring span of 0–2000 mm, providing the reach needed for sizeable fixtures, housings and assemblies. Constructed from aluminium, the design balances stiffness and manageable weight to reduce sag and handling errors during two‑person measurements. The extended range eases inspection workflows by eliminating repeated repositioning, while maintaining consistency across the measurement length. High-resolution digital readout and robust data transfer Equipped with a colour 2.4-inch touchscreen and a reading resolution of 0.001 mm, the instrument supports precise digital measurement and an intuitive operator interface. Data export is available via Wireless+USB, enabling direct connection to data-logging systems or quality software without manual transcription. Delivered fully calibrated to ISO 17025, the device includes a traceable calibration certificate, which streamlines quality documentation and reduces uncertainty in acceptance tests. Practical integration and inspection assistance for production lines The package includes an HD microscope with a 7-inch LED display that assists visual inspection during measurement tasks, ideal for checking fine details or alignment alongside dimensional checks. With digital outputs and a compact control surface, the instrument integrates into existing metrology stations and automated logging processes, improving throughput and reducing operator influence on results. This combination of traceable calibration, fine resolution and practical accessories supports reproducible measurement routines and contributes to efficient quality control. Request a consultation from Metav Werkzeuge to integrate Microtech Metrology ISO 17025‑calibrated long‑range calipers into existing measurement systems and production workflows Technical data Article number: 142520158 GTIN: 4061905036927 Manufacturer: Microtech Metrology Core specifications Measuring range: 0–2000 mm Resolution / reading: 0.001 mm Display size: 2.4 inches Data output: Wireless + USB Special features Material: Aluminium Delivered calibrated to ISO 17025 with certificate Accessory included: HD microscope with 7-inch LED display Digital instrument with colour touchscreen FAQ Is the instrument delivered calibrated to a traceable standard? The Built-in digital caliper is supplied fully calibrated to ISO 17025 and includes a calibration certificate for quality documentation. What data interfaces are supported for integration? This model offers Wireless and USB data output to transfer measurements directly from the instrument to logging systems or inspection software. What measuring range and resolution does the instrument provide? The instrument covers 0–2000 mm and provides a reading resolution of 0.001 mm; reference SKU 142520158 for this configuration. What material is the caliper made from and how does this affect use? Constructed from aluminium, the caliper delivers a balance of stiffness and reduced weight, aiding handling and repeatability across long spans. Are any inspection accessories included with the caliper? Yes, the delivery includes an HD microscope with a 7-inch LED display to support visual inspection alongside dimensional measurement. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
Increase process reliability with built-in calipers
Built-in calipers, also known as digital mounting systems or linear measuring strips, provide a cost-effective route to digitise existing machine tools, test rigs, fixtures and special-purpose machines. They permanently capture travel and positions along linear axes and convert mechanical movement into precise digital readings, improving throughput, reducing scrap and cutting manual set-up times.
How built-in calipers fit into your production flow
Engineered for direct machine integration, these systems are mounted to the moving or stationary parts of an axis so that motion is translated immediately into measurable data. The design allows horizontal and vertical mounting, while construction from high-resistance materials keeps the units dust, oil and splash-water resistant. Where access to the measuring strip is restricted, a separate, cable-connected LCD display may be positioned in the operator’s line of sight. Practical functions such as zero point setting at any position, inch-metric conversion and modern data interfaces enable straightforward transfer of positional data to higher-level control systems and process-logging equipment.
Clear production benefits you can measure
- Faster set-up: built-in calipers reduce manual adjustment time and ease repeatable setups.
- Lower scrap rates: continuous, precise position feedback minimises dimensional errors.
- Better integration: digital mounting systems provide live positional data for machine controls and quality systems.
- Increased uptime: robust linear measuring strips tolerate shop-floor contaminants and extend service intervals.
- Improved ergonomics: remote display placement keeps readings accessible without compromising machine access.
Metav as your precision partner in every workshop
Metav stands for democratisation of precision. From its base in Emmerich, Metav combines decades of application know-how with a comprehensive range that makes high-accuracy measurement attainable for industry, craft and trade. With over 48,000 customers and more than 250,000 products, Metav acts as a quality filter for the European market, supplying built-in calipers and digital mounting systems with dependable logistics and product expertise.
In brief
Built-in calipers and their synonyms — digital mounting systems and linear measuring strips — translate machine movement into accurate digital values, boosting productivity and reducing waste in industrial environments.
FAQ
How are built-in calipers mounted and oriented on a machine?
Built-in calipers can be mounted horizontally or vertically depending on the axis orientation; mounting method is chosen to ensure the measuring strip follows the machine motion precisely and remains protected from contaminants.
Can the display be placed away from the measuring strip?
Yes. Many digital mounting systems include a separate, cable-connected LCD display that can be positioned in the operator’s line of sight even when the linear measuring strip is hard to access.
Do built-in calipers support both imperial and metric units?
Built-in calipers typically offer inch-metric conversion, allowing measurements to be displayed in imperial or metric units as required for the process.
How are positional values transferred to a control system?
Linear measuring strips provide modern data interfaces for the transfer of positional data to higher-level control systems or process-logging equipment, enabling closed-loop control and data collection.
Are built-in calipers suitable for harsh workshop conditions?
Yes. The construction of these digital mounting systems from high-resistance materials renders them dust, oil and splash-water resistant, making them well suited to demanding shop-floor environments.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com