10mm Magnetic Rod Gripper D6 Smooth 2N Holding Force, Up to 450 °C - TECWERK
Compact and thermally stable magnetic holding with a 6 mm diameter and 2 N holding force enables secure retention in confined assemblies and high-temperature processes; order or request specification advice directly via Metav Werkzeuge. Magnetic rod gripper D6×H10 smooth — AlNiCo 500, 2 N holding force (TECWERK) A Magnetic rod gripper D6×H10 smooth designed for compact, high-temperature holding and precise fitting in fixtures and jigs Compact 6 mm diameter for tight spaces Stable AlNiCo 500 magnet material High-temperature capability up to 450 °C Precise h6 tolerance, dimension h: 2 mm Space‑saving hold with reliable thermal stability The compact design of the Magnetic rod gripper D6×H10 smooth offers a small footprint while delivering a 2 N holding force suitable for light retention tasks in assembly and fixturing. A 6 mm diameter and 10 mm height allow integration into tight pockets and multi-point clamps where minimal added mass is essential. Because the core material is AlNiCo 500, magnetic performance is retained under elevated temperatures, making the component applicable to processes that expose parts to heat without frequent demagnetisation. Consistent positioning through defined fit and finish Repeatable seating is provided by a defined dimension h: 2 mm together with a h6 tolerance, which ensures consistent axial location in mating bores or locating holes. This tolerance-driven fit reduces alignment variation and decreases setup time in serial production. The smooth finish minimises surface abrasion against mating parts and supports predictable contact behaviour; handling is eased and dressing or additional surface treatment is generally unnecessary. Metav’s specification team can be consulted for integration guidance. Robust material choice for long service in demanding processes Material selection emphasises endurance: AlNiCo 500 maintains useful magnetic properties to up to 450 °C, enabling use in brazing fixtures, heat-treatment stations and other high-temperature environments. The smooth execution limits particulate accumulation and is straightforward to clean during routine maintenance. Supplied as a single unit for trial fitting, the component is intended for applications that require modest magnetic retention combined with thermal resilience and compact geometry. For TECWERK magnetic gripper requirements and fast processing from Metav Werkzeuge, contact Metav Werkzeuge at +49 2822 7131930 or info@metav-werkzeuge.com for precise ordering and technical advice Technical data Article number: 4000832250NW Label: Magnetstabgreifer D6xH10mm glatt Haftkraft 2N Manufacturer: TECWERK Product type: Magnetic rod gripper Packaging unit: 1 Facts Diameter: 6 mm Height: 10 mm Holding force max: 2 N Temperature range: up to 450 °C Fit: h6; dimension h: 2 mm Special features Material: AlNiCo 500 Smooth finish Execution: smooth SKU: 4000832250NW FAQ What holding force does this magnetic rod provide? The magnetic rod gripper provides a maximum holding force of 2 N, specified for light retention tasks where modest magnetic clamping is required. Is the gripper suitable for high-temperature operations? Yes, the TECWERK magnetic rod gripper (SKU 4000832250NW) uses AlNiCo 500 and is rated for use up to 450 °C, making it suitable for elevated-temperature fixtures. How is repeatable positioning ensured? Repeatable positioning is achieved by the defined dimension h of 2 mm combined with an h6 tolerance, which ensures consistent seating in mating bores. What are the typical applications for this component? Typical uses include compact fixturing, locating aids in assemblies, brazing fixtures and heat-resistant clamping where small size and thermal stability are needed. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
10mm Magnetic Rod Gripper Smooth H16mm Holding Force 8.5N, AlNiCo 500 - TECWERK
Robust magnetic performance combined with a compact footprint and high temperature resilience ensure dependable small-part holding in demanding production environments; the combination of AlNiCo 500 construction, 8.5 N holding force and a D10 x H16 mm profile supports precise fixture integration. Order directly via Metav Werkzeuge or request specialist advice for application-specific selection. Magnetic rod gripper D10 x H16 mm smooth, holding force 8.5 N — TECWERK magnetic gripper The Magnetic rod gripper D10 x H16 mm smooth, holding force 8.5 N is a compact magnetic holding element designed for precise positioning and secure retention of small components in assembly and fixturing tasks. AlNiCo 500 magnetic alloy Compact D10 x H16 mm smooth design Holding force 8.5 N Suitable up to 450 °C, h6 fit Secure holding with temperature resilience The small magnetic element delivers a consistent holding force of 8.5 N, making it suitable for retention and light clamping tasks in assembly and handling equipment. Constructed from AlNiCo 500, the magnet retains magnetic performance at elevated temperatures — specified up to 450 °C — which reduces the need for temperature-sensitive substitutions in processes that involve heat. The compact D10 x H16 mm footprint enables installation in tight fixture pockets and minimises interference with adjacent components, supporting efficient production flow and reduced cycle times. Repeatable seating and exact positioning A defined fit dimension h = 6 mm with h6 tolerance ensures reproducible seating in housings or dowel holes, which is essential for repeatable fixturing and automated pick-and-place sequences. The smooth finish reduces abrasion against mating parts and simplifies cleaning, while the precisely machined diameter promotes reliable alignment during assembly. These characteristics translate into fewer rejects from misalignment and lower setup time when integrating the element into jigs or custom fixtures. Reliable choice for compact fixture design The compact magnetic element is engineered for low-maintenance service life thanks to stable magnetic properties of AlNiCo 500 and a robust mechanical design. The smooth version is particularly suited to applications where contact surfaces must remain unmarred and where frequent part handling occurs. For engineers and workshop managers seeking a space-efficient magnetic holding solution, this gripper offers a predictable performance profile that eases specification decisions and supports consistent production quality. For detailed application advice on the TECWERK magnetic rod gripper or to arrange rapid supply via Metav Werkzeuge, please contact Metav Werkzeuge at +49 2822 7131930 or info@metav-werkzeuge.com for personalised assistance Technical Data Article number: 4000832252NW Product type: Magnetic rod gripper Manufacturer brand: TECWERK Material: AlNiCo 500 Finish: smooth Packaging unit: 1 Facts Diameter: 10 mm Height: 16 mm Holding force (max): 8.5 N Fit dimension h: 6 mm Fit tolerance: h6 Operating temperature: up to 450 °C Special features Compact D10 x H16 mm design Smooth execution for reduced wear High-temperature-capable magnetic alloy Precise fit for fixture integration FAQ What is the maximum operating temperature for this magnetic gripper? The magnetic gripper uses AlNiCo 500 and is specified for operation up to 450 °C, allowing use in elevated-temperature environments. Which size and fit tolerance should be prepared for installation? Prepare a seating for h = 6 mm with an h6 tolerance to ensure repeatable installation and correct alignment of the gripper. How strong is the magnetic holding force? The component provides a maximum holding force of 8.5 N, suitable for light retention and positioning of small parts in fixtures. Is this product suitable for integration into compact fixtures? Yes, the compact D10 x H16 mm profile and smooth finish make the element well suited for tight fixture pockets and applications requiring minimal interference. How can Metav Werkzeuge assist with selecting the right variant? Metav Werkzeuge can advise on suitability and supply; the TECWERK magnetic rod gripper (SKU 4000832252NW) can be specified for particular assembly needs and integrated into bespoke fixtures. TECWERK: Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
13mm Magnetic Stub Gripper Smooth 12N Holding Force AlNiCo 500 - TECWERK
Compact, heat-resistant magnetic gripping for small parts: the combination of an AlNiCo 500 core, a compact 13 mm diameter and a 12 N holding force ensures secure positioning with minimal footprint — ideal for assembly jigs and inspection fixtures. Order the magnetic rod gripper directly via Metav Werkzeuge or consult the specialists for application advice. Magnetstabgreifer D13xH18mm glatt — magnetic rod gripper with AlNiCo 500 and 12 N holding force (TECWERK) A Magnetstabgreifer D13xH18mm glatt designed as a compact magnetic gripper for locating and holding small ferromagnetic components in elevated-temperature environments. AlNiCo 500 magnetic alloy core 12 N maximum holding force Smooth finish for gentle contact Rated for use up to 450 °C Precise holding with a compact footprint for production use The compact magnetic pin is built around an AlNiCo 500 magnet, which provides a stable magnetic field in a small volume and is especially suitable where consistent attraction is required over time. With a 13 mm diameter and a 18 mm overall height, the component is sized for tight assemblies and fixtures; the 12 N holding rating indicates the order of force available for locating or holding small components. The h6 fit tolerance and the additional dimension h: 7 mm are specified for accurate shaft fits and predictable positioning when integrated into jigs or carriers. This concise combination of dimensions and material makes the unit effective where space is limited but repeatability is essential. Reliability under heat and consistent performance in batches The magnetic gripper is specified for an operating temperature up to 450 °C, a parameter that allows the device to be deployed in processes with elevated thermal exposure without rapid demagnetisation typical of softer magnet grades. The smooth finish reduces mark risk on delicate parts and enables controlled contact, while the chosen magnet alloy maintains useful force at higher temperatures. For production planners and quality engineers, this translates into fewer process interruptions and consistent locating behaviour across repeated cycles, supporting process stability and predictable fixture performance. Integration and mounting advantages for workshop and industrial setups Sized for direct incorporation into fixtures, the gripper’s standardised h6 tolerance supports interchangeability and precise axial positioning when used in shafts or bores. The compact form factor and clearly defined 7 mm auxiliary dimension simplify CAD placement and mechanical design, reducing integration time. The robust construction and defined mechanical data mean the component can be specified in assembly instructions and procurement lists with confidence, enabling a transparent supply chain and smoother implementation on the shop floor. Contact Metav Werkzeuge for tailored advice on integrating the TECWERK magnetic rod gripper into fixtures and jigs, or request support for specifying tolerances and thermal requirements — Metav Werkzeuge is ready to assist. Technical data Article number: 4000832253NW Item: Magnet rod gripper D13×H18 mm, smooth, holding force 12 N Numbers / core technical data Diameter: 13 mm Height: 18 mm Holding force (max): 12 N Additional dimension h: 7 mm Fit tolerance: h6 Operating temperature: up to 450 °C Packaging unit: 1 Special features / materials Material: AlNiCo 500 Smooth version (glatte Ausführung) Manufacturer brand: TECWERK SKU: 4000832253NW FAQ Is the magnetic rod gripper suitable for elevated-temperature operations? The Magnetstabgreifer D13xH18mm glatt is specified for use up to 450 °C, which supports applications with higher thermal exposure while retaining functional magnetic performance. What is the maximum holding force and what does it imply? The device offers a 12 N maximum holding force; this value describes the peak attractive force under defined conditions and is intended for locating and holding small ferromagnetic parts rather than heavy load-bearing tasks. Which material is used for the magnet and what are its benefits? The rod contains AlNiCo 500, a high-temperature-capable magnetic alloy that provides stable magnetic performance at elevated temperatures and good long-term stability in repeated thermal cycles. How does the fit tolerance affect integration into fixtures? The h6 fit tolerance ensures a precise shaft fit and repeatable axial positioning when the gripper is installed in bores or holders, simplifying fixture design and interchangeability. Can the smooth finish be used on delicate surfaces? The smooth finish is intended to minimise marking and enable gentler contact with components; it suits applications where surface protection is a consideration. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
25mm Magnetic Rod Gripper Smooth, Holding Force 40N, AlNiCo 500 - TECWERK
Reliable compact holding that copes with high temperatures and confined spaces: a compact Ø 20 mm body combined with a 40 N maximum holding force and AlNiCo 500 magnet material supports secure short-term fixation in assembly and tooling. Order directly via Metav Werkzeuge or consult our specialists for application-specific advice. Magnetic rod gripper D20×H25 mm — smooth, 40 N holding force (TECWERK) The Magnetic rod gripper D20×H25 mm smooth is a compact magnetic clamp designed for precise positioning and temporary holding of small ferrous components in production, assembly and inspection tasks. Smooth AlNiCo 500 surface Compact Ø 20 mm design Holding force 40 N Temperature resistance up to 450 °C Secure small-part holding with measurable performance The compact format provides a predictable holding characteristic: a cylindrical body with Ø 20 mm and a total height of 25 mm gives a stable contact area for small fixtures while keeping the footprint minimal. The specified 40 N holding force describes the peak pull capability under standard test conditions and translates into reliable short-term fixation for light assemblies, jigs or pick-and-place operations. This measured value supports process planning and reduces trial-and-error during fixture design. Material selection for thermal stability and magnetic consistency Built from AlNiCo 500, the magnet core offers stable magnetic properties at elevated temperatures and good demagnetisation resistance compared with standard ferrite magnets. AlNiCo 500 retains useful magnetic strength where heat is present, allowing operation up to 450 °C without rapid loss of performance. For production environments that include heat cycles or near-heat processes, this material choice reduces the need for frequent replacement and maintains holding performance over time. Precision fit and installation advantages Additional geometric data includes a dedicated dimension h: 5 mm with a h6 tolerance class; this defines a close-fitting datum for press or slip fits and ensures repeatable positioning in housings or tool plates. The h6 tolerance indicates a tight shaft fit commonly used in precision assemblies, reducing play and improving repeatability in repetitive operations. Clear dimensional control lowers setup time and contributes to consistent assembly quality. Gentle contact and versatile application range The smooth finish prevents unnecessary marking on mating parts and is therefore suitable for short-term contact with prepared surfaces. The combination of compact geometry and thermal resistance makes the component well suited to fixture points, temporary tacking in welding pre-assembly and sorting tasks where gentle magnetic support is required. The TECWERK magnetic rod gripper balances low profile design with practical holding capacity for everyday workshop and small-scale industrial tasks. For robust high-temperature magnetic holding choose the TECWERK magnetic rod gripper and contact Metav Werkzeuge for procurement and technical advice from Emmerich: info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: 4000832255NW Product: Magnetic rod gripper Manufacturer: TECWERK Material: AlNiCo 500 Finish: smooth Packaging unit: 1 Facts Diameter: 20 mm Height: 25 mm Holding force: 40 N Operating temperature: up to 450 °C Dimension h: 5 mm; tolerance: h6 Special features Smooth execution AlNiCo 500 magnet material Compact design Packaging unit 1 FAQ What types of parts are suitable for magnetic holding? The magnetic rod gripper is designed primarily for ferrous components and supports temporary fixation of steel parts and similar magnetic materials. What is the maximum operating temperature? TECWERK specifies an operating temperature up to 450 °C for this magnetic rod gripper, reflecting the thermal resilience of the AlNiCo 500 material. What does the h6 tolerance mean for installation? A h6 tolerance indicates a close shaft fit; it ensures a snug installation with minimal play when the 5 mm h dimension is used as a locating feature. How strong is the grip in practical terms? The device provides a maximum holding force of 40 N, suitable for short-term holding and light fixture duties rather than heavy lifting. Will the finish mark delicate surfaces? The smooth execution reduces point marking and is intended for short-term contact where minimal surface impact is required. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
8mm Magnet Rod Gripper Smooth, 4N Holding Force, AlNiCo 500 - TECWERK
Compact magnetic handling and high-temperature resilience combine in this compact unit: reliable 4 N holding force, AlNiCo 500 construction and a smooth finish enable secure part handling in demanding production settings; order directly via Metav Werkzeuge or consult our specialists for integration advice. Magnet rod gripper D8×H12 mm — smooth finish, 4 N holding force (TECWERK) A Magnet rod gripper D8×H12 mm designed for precise part pick-up and positioning in assembly, inspection and light automation tasks. AlNiCo 500 magnetic alloy construction High holding force: 4 N Compact D8×H12 mm smooth design Operates up to 450 °C with h6 tolerance Secure grip for delicate handling and repeatable pick-up The compact magnetic gripper delivers a 4 N holding force while preserving component surfaces thanks to its smooth finish. Constructed from AlNiCo 500, the alloy combines stable magnetic properties with resistance to demagnetisation at elevated temperatures, which translates into predictable performance across production cycles. The moderate holding capacity is ideal for small fixtures, rotating inspection stations and sensitive parts where over‑clamping would risk deformation. By converting raw magnetic parameters into practical outcomes, the unit supports consistent pick-and-place tasks with minimal setup time and reduced part damage. Built for heat and tolerance-critical processes Designed to tolerate temperatures up to 450 °C, the gripper is suitable for heat-treatment, brazing or processes near ovens where standard magnets would lose effectiveness. The supplied specification includes a h6 tolerance and a secondary dimension 3 mm for the interface, ensuring reproducible fits into housings or dedicated mounting sleeves. Explaining the terms: h6 denotes a tight shaft-to-bore fit class that helps preserve concentricity, and the declared operating temperature indicates retained magnetic performance rather than mere thermal resistance. These attributes make the device a reliable choice when thermal cycles and dimensional precision are combined requirements. Space-saving design for straightforward integration With outside dimensions D8×H12 mm and a smooth execution, the component is optimised for compact assemblies and retrofit into existing grippers or end‑of‑arm toolings. The minimal footprint reduces interference in dense layouts and simplifies collision avoidance in automated cells. The polished surface minimises friction and particulation, aiding maintenance in cleaner environments, while the magnetic alloy construction reduces the need for mechanical clamps on small parts. As a small, ready-to-install magnetic element, it supports faster machine cycles and lower tooling complexity without compromising positional repeatability. Contact Metav Werkzeuge for tailored supply and technical advice on TECWERK magnetic rod grippers; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 4000832251NW Product: Magnet rod gripper Brand: TECWERK Material: AlNiCo 500 Finish: smooth Core data Diameter: 8 mm Height: 12 mm Holding force (max): 4 N Operating temperature: up to 450 °C Tolerance class: h6 Dimension h: 3 mm Packaging unit: 1 Special features Compact D8×H12 mm design Smooth execution for minimal marking Suitable for high-temperature applications up to 450 °C Repeatable magnetic performance due to AlNiCo 500 FAQ What is the maximum holding capacity of this magnetic element? The maximum holding capacity is 4 N for the Magnet rod gripper D8×H12 mm, suitable for light part handling and positioning tasks. Can the gripper be used in high-temperature environments? Yes, the TECWERK magnetic rod gripper maintains performance up to 450 °C, making it appropriate for processes with elevated temperatures. What does the h6 tolerance mean for installation? A h6 tolerance indicates a close fit for the interface dimension; the gripper’s specified 3 mm dimension h and h6 class enable precise, reproducible mounting in housings or sleeves. Is the surface finish suitable for fragile components? The smooth execution reduces surface abrasion and particulation, so the device is well suited for handling delicate parts where marking must be minimised. Which alloy is used and why is it relevant? The gripper is made from AlNiCo 500, an alloy known for stable magnetic properties at higher temperatures and resistance to demagnetisation, which supports consistent handling performance. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com