100mm Parallel Gauge Set Precision Pair Ground, Hardened, 20 Pairs, IT5 ±0.01mm - AMF
Secure consistent assembly and fixturing with a set engineered for exact stacking and minimal variation; the hardened, pairwise plan-parallel plates offer ±0.01 mm height accuracy and enable quick, reliable shimming in 1 mm increments — order through Metav Werkzeuge or consult the advisers for specification matching. AMF Parallel shim set No. 6348P – 100 mm, pairwise precision shims the AMF Parallel shim set No. 6348P is a precision shimming solution for accurate height adjustment and toolbox-ready fixture alignment in workshop and production environments Pairwise plan-parallel, finely ground Case-hardened for long service life Height tolerance ±0.01 mm (IT5) Stackable in 1 mm increments Faster, more reliable setup through precision shimming The set provides 20 pairs of 100 mm shims that are pairwise plan-parallel and finely ground, which makes them ideal for accurate machine set-up and repeatable fixturing. Because each pair is matched and case-hardened, the risk of deformation under clamp load is reduced, preserving alignment and minimising rework. The combination of matched pairs and a clear stacking system cuts adjustment time, translating into measurable productivity improvements on assembly lines and jigs. Measurable accuracy that supports quality assurance Manufactured to tight tolerances with a pair tolerance tp in the height IT5 and nominal height tolerance ±0.01 mm, the plates enable precise compensation of misalignment where micron-level control matters. Compliance with DIN ISO 2768 m for the remaining dimensions ensures predictable integration with existing tooling. For tasks requiring reproducible gap control or calibrated reference heights, these shims offer a technical basis for traceable processes and lower scrap rates. Durable design tailored for industrial handling and storage Delivered as a comprehensive set, the shims are optimised for repeated use: hardened surfaces resist wear, while the fine grind maintains planarity under load. Sets are arranged to allow 1 mm stacking increments, simplifying the selection of the correct build-up without trial-and-error. The format supports both precision toolrooms and busy production bays where robust, easy-to-identify shimming solutions are required. For precision shimming from AMF, contact Metav Werkzeuge in Emmerich for expert advice and fast supply — Metav’s team can confirm compatibility with specific fixtures and ordering options Technical Data Article number: 4123321018NW Type: Nr. 6348P - 100 Label: Parallelunterlagensatz Nr.6348P Inh.20 PA Gr.100 Präzision L.100mm AMF Manufacturer: AMF Product type: Parallel shim set Content: 20 pairs Facts Length: 100 mm Quantity: 20 pairs Pair tolerance: tp in height IT5 Nominal height tolerance: ±0.01 mm Stacking increments: 1 mm Special features Pairwise plan-parallel, finely ground Case-hardened for wear resistance Sets provide a range with 1 mm steps Remaining dimensions to DIN ISO 2768 m FAQ What materials are these shims suitable for in fixture work? The AMF parallel shim set No. 6348P is a general-purpose shimming solution intended for steel and common fixture materials; material compatibility depends on application loading and environment, with the hardened finish providing broad suitability. How precise is the height control when stacking plates from this set? Stacking plates from the set yields step-controlled height adjustments in 1 mm increments with a nominal height tolerance of ±0.01 mm, allowing precise and repeatable build-ups. Are the shims matched within pairs for planarity? Yes, each pair is matched and plan-parallel, finely ground, ensuring consistent contact surfaces and minimised variation when used under clamping pressure. Can these shims be used in calibrated measurement setups? The set’s tight height tolerance and pairwise matching support use in setups requiring repeatable reference heights; however, final suitability depends on the specific metrology chain and requirements. What is the product reference for ordering or specification checks? Refer to SKU 4123321018NW and type Nr. 6348P - 100 when specifying the AMF parallel shim set for procurement or technical verification. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
110mm Parallel Shim Set Wavy 8 Pairs 0.3mm Hardened Spring Steel ±0.004mm Pair Tolerance IT5 - AMF
Take advantage of a precision-engineered shim set that combines precision-ground surfaces, hardened spring steel and tight height tolerances for repeatable clamping and minimal setup time. Order the AMF set directly via Metav Werkzeuge or consult the Metav advisors for workshop-specific recommendations. Parallel shim set No. 6344SP — wave-shaped, precision-ground shims by AMF A Parallel shim set No. 6344SP designed for precise stacking and clamping of thin or multiple workpieces in machining and inspection environments Precision-ground spring steel Height steps of 2 mm Pair tolerance IT5 in height Nominal height tolerance ±0.004 mm Wave-shaped top reduces swarf retention Repeatable stack heights for efficient clamping The set provides precision-ground shims manufactured from hardened and tempered spring steel, delivering consistent stack heights and reliable repeatability in fixturing. Tight dimensional control — including a pair tolerance to IT5 and a nominal height tolerance of ±0.004 mm — reduces the need for repeated adjustments and speeds up changeovers. The wave-shaped top face assists in avoiding trapped chips on the support surface, which contributes to maintaining the intended clamping plane and protects the parallelism of the clamped component. Material choice and tolerances that save setup time The combination of spring steel and precision finishing ensures longevity under repeated clamping cycles while remaining thin enough for fine height adjustments. A material thickness of 0.3 mm and clearly defined height gradation of 2 mm allow for controlled buildup of shim stacks rather than improvisational packing. This reduces operator effort during setup and minimises the risk of stacked instability. Compliance of remaining dimensions with DIN ISO 2768 provides compatibility with standard tooling and fixturing practices in professional workshops. Practical design for cleaner, safer workshop use The wave-shaped surface geometry keeps the load zone clear of swarf, so the parallelism of the clamped workpiece is not impaired and no additional cleaning steps are required between adjustments. Precision grinding of each element preserves flatness on the bearing faces, which is beneficial when clamping several flat or individual thin components together. The set is intended for straightforward integration into existing clamping routines and is suited to industrial and trade environments where repeatability and cleanliness are priorities. For reliable, precision clamping with AMF quality, contact Metav Werkzeuge to discuss the Parallel shim set No. 6344SP and its suitability for specific workshop applications; Metav Werkzeuge can provide technical advice and swift supply from Emmerich Technical Data SKU: 4000603656NW Type: Nr. 6344SP - 25-39 Product type: Parallel shim set Manufacturer: AMF Content: 8 pairs Overall length: 110 mm UID: 4000603656NW Facts Material thickness: 0.3 mm Height gradation: 2 mm Pair tolerance: IT5 (height) Nominal height tolerance: ±0.004 mm Remaining dimensions: per DIN ISO 2768 Special features Wave-shaped top surface Precision-ground bearing faces Spring steel, hardened and tempered No swarf retention on support surface Maintains parallelism of clamped workpiece Suitable for multiple flat or single thin workpieces FAQ What material are the shims made from and how does that affect durability? The AMF Parallel shim set No. 6344SP is made from hardened and tempered spring steel, which offers high fatigue resistance and maintains flatness under repeated clamping cycles. What tolerances can be expected for stack heights? Stack-building with the Parallel shim set No. 6344SP is supported by a pair tolerance to IT5 and a nominal height tolerance of ±0.004 mm, ensuring reproducible results in jigs and fixtures. Is the surface finish suitable for precision inspection fixtures? Yes, the precision-ground faces of the Parallel shim set No. 6344SP provide flat bearing surfaces that support accurate clamping and do not interfere with inspection tolerances. Will chips or swarf affect clamping accuracy with these shims? The wave-shaped top profile reduces swarf retention on the support face, so the parallelism of the clamped component is preserved and additional cleaning between adjustments is often unnecessary when using this set. Can the shims be combined to clamp very thin workpieces? The design allows easy stacking of several shims to achieve fine height adjustments, making the set suitable for clamping multiple thin or flat workpieces in a controlled manner. Manufacturer: AMF; Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
110mm Parallel Shim Set Wavy 8 Pairs 0.3mm Material Thickness, Precision Ground - AMF
Take advantage of precision-ground, hardened spring steel shims with 0.3 mm thickness and a clear 2 mm height stepping to maintain workpiece parallelism and reduce setup time; order directly via Metav Werkzeuge or contact our advisers for configuration assistance. AMF Parallel shim set Nr. 6344SP - 9-23 (wavy profile, 110 mm) The AMF Parallel shim set Nr. 6344SP - 9-23 is a specialised collection of precision shims designed for accurate clamping and alignment in metalworking and general workshop fixturing. Wavy profile prevents chips on support surface Precision-ground shims, thickness 0.3 mm Hardened and tempered spring steel Height increments 2 mm, pair tolerance IT5 Maintain true parallelism with fast, repeatable setups Precision shims deliver measurable gains in setup reliability. The precision-ground surfaces and pair tolerance IT5 ensure nominal height deviations are held to ±0.004 mm, which reduces rework and inspection time. Using stepped shims streamlines the process of shimming between jaws or supports, so maintaining true parallelism of the clamped workpiece becomes a routine task rather than a daily challenge. This directly improves throughput and machining consistency. Durable material and profile for clean contact surfaces Built from hardened and tempered spring steel, the shims tolerate repeated clamping without deformation, extending service life and lowering replacement frequency. The wavy profile minimises contact of loose chips with the underside of the workpiece, so debris is less likely to compromise the contact surface. This leads to more consistent clamping forces and a lower risk of surface marking on delicate parts, preserving component quality during handling and machining. Precise increments that simplify multi‑part clamping With a 0.3 mm material thickness and 2 mm height steps, the set offers fine, graduated adjustment for stacking or combining shims to reach the required clearance. The small thickness and clear stepping make it straightforward to clamp several flat or thin components together without loss of alignment. These features reduce setup iterations and support efficient jigs and fixtures where repeatable, small adjustments are essential. Engineered tolerances for measurement confidence Tolerance design follows recognised standards to support predictable results: nominal height tolerance of ±0.004 mm and remaining dimensions in accordance with DIN ISO 2768m. Such specifications provide a verifiable basis for procurement decisions and quality audits, allowing the set to be integrated into measurement-controlled workflows and documented procedures with minimal additional calibration. Contact Metav Werkzeuge for tailored advice on integrating the AMF shims into existing fixtures and order support directly from Emmerich Technical Data Article number: 4000603655NW Type: Nr. 6344SP - 9-23 Product: Parallel shim set Brand: AMF Content: 8 pairs Length: 110 mm Facts Material thickness: 0.3 mm Height step: 2 mm Pair tolerance: tp in height IT 5 Nominal height tolerance: ±0.004 mm Length: 110 mm Set content: 8 pairs Special features Wavy profile to reduce chip retention Precision-ground surfaces Hardened and tempered spring steel Remaining dimensions per DIN ISO 2768m Advantage: no chips remain on support surface Preserves parallelism of clamped workpiece Enables clamping of several thin or flat workpieces FAQ What material are the shims made of? The shims are manufactured from hardened and tempered spring steel, which gives the AMF shim set good wear resistance and spring characteristics suited to repeated clamping. How fine are the height increments? Height increments are 2 mm per step; combined with the 0.3 mm thickness of each shim, this allows precise stacking and fine adjustment when setting up fixtures. What tolerances can be expected for height? Nominal height tolerance is ±0.004 mm and pair tolerance is specified as IT5, ensuring consistent, repeatable height control for precision applications. Can these shims prevent chips from affecting the clamping surface? Yes, the wavy profile reduces chip retention on the support surface, helping to maintain clean contact and consistent clamping pressure. Is this set suitable for clamping multiple thin workpieces? The design and fine thickness make the set suitable for clamping several flat or thin components without compromising parallelism. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
125mm Parallel Gauge Set Pair-Set Precision Ground 24 Pairs ±0.01 mm - AMF
Benefit from hardened, case‑stored precision and pairwise plan‑parallel finishing for reliable stackable shimming; order the AMF Parallel shim set directly via Metav Werkzeuge or consult the technical team for specification support. Parallel shim set No. 6348P - 125 by AMF — 24 pairs, 125 mm, case‑hardened The Parallel shim set No. 6348P - 125 is a precision shimming kit for exact height setting and gap compensation in jigs, fixtures and machine set‑up. Precision, pairwise ground and parallel Case‑hardened for lasting wear resistance 1 mm step coverage across the set Height tolerance IT5 ±0.01 mm Precision shimming for reproducible set‑up The AMF set delivers measured, repeatable results because each shim is pairwise ground and finished to be plan‑parallel. This manufacturing approach guarantees consistent contact surfaces when shims are stacked, so nominal build‑ups increase in exact increments. With a height tolerance of IT5 and a declared accuracy of ±0.01 mm, the kit supports fine adjustment tasks where micrometric control matters. The 1 mm step arrangement across the set simplifies calculation of cumulative heights, reducing trial‑and‑error and shortening set‑up time in series production or toolmaking. Durable construction and tidy storage for workshop use Components are case‑hardened, providing improved surface hardness and resistance to wear under repeated handling and clamping forces. The set is supplied in a protective wooden case, which keeps elements organised and prevents accidental mixing of pairs — a practical advantage for busy benches. Each shim measures 125 mm in length and the complete delivery contains 24 pairs, making the assortment suitable for a wide range of machine‑side and assembly tasks where stable, long‑term accuracy is required. Conformity, compatibility and operational benefits Manufactured with reference to DIN ISO 2768m, the shims offer standardised dimensional integrity and are suitable for integration into existing fixture systems and measurement routines. The clearly defined increments and traceable tolerance class help maintenance teams and quality departments to document adjustments and reproduce settings reliably. As a precision accessory for production and maintenance, the set reduces waste caused by incorrect shimming and supports efficient changeovers in both single‑piece flow and repetitive operations. Technical enquiries regarding suitability for specific applications are welcome. For hardened, high‑precision height setting, order the AMF Parallel shim set No. 6348P - 125 via Metav Werkzeuge or contact Metav Werkzeuge for tailored technical advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 4123321021NW Type: Nr. 6348P - 125 Brand: AMF Product: Parallel shim set Content: 24 pairs Facts Length: 125 mm Step increments: 1 mm Height tolerance: IT5 ±0.01 mm Standard: DIN ISO 2768m Special features Case‑hardened Pairwise plan‑parallel fine ground Wooden storage case Sets cover step range with 1 mm increments FAQ What is the stated height tolerance of the set? The AMF Parallel shim set No. 6348P - 125 is specified with a height tolerance of IT5 and a nominal tolerance of ±0.01 mm. How many shims are included and what are their dimensions? The delivery contains 24 pairs of parallel shims; each element is 125 mm long and arranged to cover heights in 1 mm increments across the set. Are the shims suitable for repeated clamping and fixture use? Yes — the shims are case‑hardened to improve surface durability, making the set appropriate for frequent handling and clamping operations in workshop environments. Is the finish suitable for stacking without introducing tilt? Pairwise plan‑parallel finishing ensures flat contact faces; this pairwise ground quality limits cumulative error when shims are stacked for height build‑up. Which standard governs the remaining dimensions of the set? Remaining dimensions and general tolerances are produced in accordance with DIN ISO 2768m for consistent integration into tooling and fixtures. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
150mm Parallel Gauge Set Pairwise Ground, Hardened, Size Marked, 0.01mm Pair Tolerance - AMF
Take advantage of a durable, case‑hardened construction and pairwise plan‑parallel grinding for consistent setups; combined with clear size markings and a compact wooden box, the set streamlines fixture preparation and repeatable adjustments. Order the AMF Parallel shim set Nr. 6347S directly via Metav Werkzeuge or ask our consultants if needed. AMF Parallel shim set Nr. 6347S — 150 mm standard length, 14 pairs Parallel shim set Nr. 6347S for precise height compensation and fine adjustment tasks in metalworking, toolmaking and precision setup applications. Standard wooden case with removable lid Case-hardened for durable wear resistance Pairwise ground and plan‑parallel accuracy Size markings and 0.01 mm pair tolerance Consistent, measurable accuracy for precise setups The set delivers reliable precision through pairwise fine grinding that ensures plan‑parallel contact faces and a documented pair tolerance of 0.01 mm, making it suitable where repeatability matters. Such tight control of thickness minimises cumulative error when stacking shims during fixturing or measurement tasks, so setups remain within predictable limits and rework is reduced. The result is faster alignment and fewer inspection iterations on the production floor. Robust treatment for long service life and stable reference A case‑hardened finish provides wear resistance and maintains contact surfaces under repeated use, preserving the original thickness and surface integrity over time. This hardening reduces the need for frequent replacement and helps maintain stable reference heights in jigs and fixtures. The mechanical resilience therefore contributes directly to lower downtime and a steady quality output in everyday workshop operations. Organised handling and straightforward identification Each shim carries size markings to speed selection and limit handling errors, while the wooden box with a removable flap lid keeps the components protected and readily accessible at the bench. Clear labelling and neat storage reduce search times during set‑up changes, improving workflow efficiency in busy environments. The compact storage solution supports tidy tool stations and faster job changeovers. Conformity and traceable tolerances for quality assurance Nominal tolerances are applied in accordance with DIN ISO 2768m, ensuring dimensional consistency across the set and compatibility with standardised tooling workflows. Where a tight pair tolerance is required, this conformity simplifies inspection and documentation processes, supporting quality control regimes and audit trails. The combination of standardised tolerances and precise manufacturing aids verification and integration into certified production processes. For workshop‑grade precision and dependable durability, contact Metav Werkzeuge to secure the AMF Parallel shim set Nr. 6347S and receive expert advice from our Emmerich team. Technical Data Article number: 4123321010NW Type: Nr. 6347S Product: Parallel shim set Brand: AMF Core data Length: 150 mm Content: 14 pairs Pair tolerance: 0.01 mm Packaging unit: 1 Special features Case-hardened Pairwise ground and plan‑parallel Size markings on each shim Wooden box with removable flap lid Nominal tolerances according to DIN ISO 2768m FAQ What accuracy can be expected from these shims? The AMF Parallel shim set Nr. 6347S provides a documented pair tolerance of 0.01 mm, ensuring high repeatability for stacking and fine adjustments. How is the set supplied and stored? The set is supplied in a wooden box with a removable flap lid; each shim is marked for easy identification and organised storage. Are the dimensional tolerances standardised? Yes, nominal tolerances for the set comply with DIN ISO 2768m, providing traceable conformity for quality assurance and integration into standard workflows. Is the construction suitable for frequent workshop use? The case‑hardened treatment and ground surfaces of the AMF set offer wear resistance and stable reference dimensions under repeated handling. Can the shims be used for precise fixture adjustments and measurement setups? Designed for height compensation and setup tasks in metalworking and toolmaking, this parallel shim set serves as a reliable element for precise fixture and measurement preparations. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
150mm Precision Parallel Shim Set Pair-Matched Ground 24 Pairs, Hardened, 0.01mm Height Tolerance IT5 - AMF
Benefit from precise, wear-resistant shims with fine pair-matching and tight height tolerances for reliable set-up and inspection. Combine case-hardened durability, pairwise fine-ground accuracy and a practical 1 mm increment range for efficient workshop operation. Order the set directly via Metav Werkzeuge or consult the technical team for application advice. Parallel shim set Nr. 6348P - 150 — Precision pair-matched shims, 150 mm length (AMF) A Parallel shim set Nr. 6348P - 150 designed for precision shimming and spacing in clamping, inspection and jigging applications across metalworking workshops Precision ground in matching pairs Case-hardened for long-term wear resistance Set provides 1 mm increments Nominal height tolerance ±0.01 mm Precise pairing for repeatable, measurable set-ups The set is manufactured to deliver consistent thickness across mating pairs, with a declared pair tolerance (IT 5) and a nominal height tolerance of ±0.01 mm. These specifications ensure that each paired shim behaves predictably under load, reducing adjustment time during fixture assembly and inspection. IT grades and micron-level tolerances are standard ways to quantify manufacturing precision; in practice this means the shims support reproducible component positioning and reliable measurement transfer between setups. Hardening and surface finish that extend service life The shims are case-hardened, giving a hardened surface layer that improves resistance to wear and indentation while retaining a tough core. Surface treatment combined with fine-ground, flat-parallel finishing minimises local deformation when used between clamping faces. Case-hardening (surface carburising) creates a durable contact surface without making the entire part brittle, which is particularly advantageous for frequent re-use in workshop and inspection environments where small deviations affect final tolerances. Practical range and workflow benefits for workshops Contained as a matched set of 24 pairs with a nominal length of 150 mm, the kit covers a sensible stepping range in 1 mm increments, allowing rapid selection of the required build-up without time-consuming custom shimming. The modular range reduces the number of components needed in inventories and speeds up vice, fixture and gauge set-ups. For toolmakers and inspection technicians, the clear increments and matched pairs translate directly into fewer iterative adjustments and shorter machine downtime. Compliance, handling and storage that support precision Manufactured and ground to meet common engineering drawing conventions and dimensional control (remaining dimensions per DIN ISO 2768m where applicable), the set is supplied prepared for immediate workshop use. The fine-ground surfaces and defined tolerances simplify calibration routines and reduce the need for extra surface preparation. Packaged for workshop handling, the set maintains organisation and protects the ground faces during transport and storage, helping to preserve the declared specifications over time. For application-specific advice or to arrange supply of the AMF Nr. 6348P - 150 parallel shim set, contact Metav Werkzeuge in Emmerich; technical consultants can advise on selection and availability via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data SKU: 4123321022NW Type: Nr. 6348P - 150 Product: Parallel shim set Brand: AMF Content: 24 pairs Length: 150 mm Facts Pair tolerance: IT 5 Height tolerance: ±0.01 mm Increment: 1 mm Special features Case-hardened surface Pairwise fine-ground, flat-parallel Sets cover range with 1 mm steps Supplied for workshop use FAQ What tolerance can be expected from these shims? The parallel shim set Nr. 6348P - 150 is specified with a pair tolerance of IT 5 and a nominal height tolerance of ±0.01 mm, providing stable, measurable accuracy for precision set-ups. How many shims are included and what increments do they cover? The AMF parallel shim set contains 24 pairs and is arranged to provide 1 mm incremental build-up across its useful range. Are these shims suitable for frequent clamping use? Yes; the case-hardened surface and fine-ground finish make the shims resistant to wear and suitable for repeated clamping and inspection tasks without rapid degradation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com