120mm Horizontal Clamp With Angle Foot M5 x 30 Pressure 800N Holding 1100N - AMF
Achieve secure fixturing with the AMF Horizontal clamp No. 6833, Size 1 with angular foot: the combination of a 1,100 N holding force, 800 N clamping force and compact construction supports reliable, repeatable setups. Order the clamp directly via Metav Werkzeuge or consult the Metav specialists for tailored fixture advice. AMF Horizontal clamp No. 6833, Size 1 with angular foot — compact fixturing with high holding power The AMF Horizontal clamp No. 6833, Size 1 with angular foot is a compact clamping unit designed for jigs and fixtures where space is limited and dependable workpiece retention is required. Compact size 1 for tight fixtures Holding force 1,100 N for secure clamping Clamping force 800 N for stable operations Pressure screw M5 x 30 for fine adjustment Reliable clamping performance for repeatable setups The horizontal clamping unit delivers a measurable holding force of 1,100 N and a clamping force of 800 N, ensuring that workpieces remain immobile under machining or assembly loads. These figures translate into fewer rejects and less rework, as the fixture holds parts consistently during cycles. The compact Size 1 format minimises interference with tooling paths while maintaining the necessary retention force for small to medium components, which helps to reduce set-up time and increase throughput on production lines. Flexible mounting thanks to the angular foot An integrated angular foot provides versatile mounting options for the clamp, enabling attachment on vertical or horizontal surfaces without additional adapters. The long base dimension L1 120 mm and the clearances indicated by H, H1, H2 allow predictable positioning in complex jig constructions. This adaptability supports efficient machine bed use and allows fixtures to be designed with shorter tooling envelopes, improving accessibility and reducing collision risks during operation. Precise pressure control for delicate adjustments Fine-tuning of clamping pressure is achieved via the M5 x 30 pressure screw, which permits gradual increase of contact force without abrupt shocks to the workpiece. This adjustability is particularly beneficial for fixtures handling delicate or thin-walled components where excessive force would cause deformation. The screw-based adjustment simplifies repeatable setups and allows maintenance of consistent clamping conditions across production batches. Built for workshop and industrial fixturing needs The clamp suits a wide range of shop-floor applications, from small-batch jigs to serial production fixtures. Its combination of compact form and robust retention supports reliable process control and reduces operator intervention. The measured parameters and standardised attachment points make integration into existing fixtures straightforward, accelerating project deployment and contributing to predictable cycle times and improved overall equipment effectiveness. Secure machining setups with AMF's compact horizontal clamp are available through Metav Werkzeuge — contact Metav Werkzeuge for availability and personalised fixture guidance at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 4000604353NW Type: 6833 Product: Horizontal clamp Label: Waagrechtspanner Nr.6833 Gr.1 Winkelfuß AMF Brand: AMF Core figures Holding force max: 1,100 N Clamping force max: 800 N Pressure screw: M5 x 30 L1: 120 mm H: 57 mm H1: 68 mm H2: 49 mm A: 5 mm B: 32 mm C: 13.5 mm D: 5.2 mm E: 18.5 mm F: 4 mm I: 10 mm K: 8 mm M: 19 mm N: 31 mm P: 28 mm Angle a: 90° Special features With angular foot Size: 1 Pressure screw M5 x 30 Packaging unit: 1 FAQ What are the holding and clamping forces of this clamp? The AMF Horizontal clamp No. 6833 (SKU 4000604353NW) provides a holding force of 1,100 N and a clamping force of 800 N. How is the clamp mounted in a fixture? Mounting is via the angular foot, allowing attachment to vertical or horizontal surfaces; the base length L1 120 mm and standardised dimensions simplify positioning. Is the clamping pressure adjustable? Yes, clamping pressure is adjusted using the M5 x 30 pressure screw for fine, controlled changes in contact force. For which applications is this clamp best suited? The clamp is suitable for jigs and fixtures in workshop and industrial settings, especially where compact retention with reliable holding is required. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
120mm Horizontal Clamp With Horizontal Base, 800 N Clamping Force, 1 Pc - AMF
Take advantage of a compact, robust clamping solution that combines a Size 1 footprint with a low-profile horizontal foot and a reliable clamping force of 800 N, delivering secure holding of up to 1,100 N for fixture and jig applications. Order the AMF horizontal clamp directly via Metav Werkzeuge or consult our specialists for application guidance. AMF Horizontal Clamp No. 6830 (Size 1) with Horizontal Foot — 800 N clamping force The AMF Horizontal Clamp No. 6830 (Size 1) is a compact horizontal clamping device designed for fixture and jig work where a low-profile horizontal foot is required, providing dependable clamping and repeatable positioning in constrained spaces Compact size 1 for space-saving fixtures Horizontal foot for low-profile mounting Max clamping force 800 N, holding 1,100 N Includes M5 x 30 pressure screw Precise, space-saving clamping for jigs and fixtures The horizontal clamp offers a compact Size 1 construction that suits tight fixture configurations while keeping machining envelopes clear. Its low-profile horizontal foot reduces interference with adjacent components and allows mounting where vertical clearance is limited. The combination of compact dimensions and lateral mounting makes the unit ideal for repetitive production setups, assembly jigs and manual fixture stations where consistent lateral clamping is required. The incorporated M5 x 30 pressure screw permits secure adjustment and fine setting of the contact point, supporting reliable part location without additional adapter elements. Reliable holding and repeatable forces for process security Engineered for industrial use, the clamp provides a clamping force of up to 800 N and a holding force of 1,100 N, ensuring firm part retention during machining or assembly steps. The device’s adjustable elements — shown in the dimensional data — allow an adaptable clamping range for varying stock thicknesses, delivering reproducible pressure across cycles. For production planners and quality engineers, this means fewer rejects from part movement and more predictable process capability. The mechanism is straightforward to integrate into existing fixtures, translating force specifications into verifiable holding behaviour on the shop floor. Practical dimensions and adjustable range for flexible use Key dimensions and adjustment windows are provided to aid fixture design and NC programming. The item includes an adjustable clamping range (C: 13–14.5 mm) and stroke/height parameters that facilitate quick integration into bespoke workholding. These measurable values support precise CAD layout and help determine clearance envelopes. Where system robustness and repeatability are priorities, the unit’s physical parameters allow engineers to calculate leverage, contact pressure and potential interference, reducing trial-and-error during fixture assembly. For assured fixture performance and integration support, order the AMF Horizontal Clamp No. 6830 via Metav Werkzeuge — for technical advice and availability contact info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: 4000833507NW Manufacturer: AMF Type: 6830 Product type: Horizontal clamp with horizontal foot Packaging unit: 1 Facts Max clamping force: 800 N Max holding force: 1,100 N A: 5 mm B: 42 mm C: 13–14.5 mm D: 5.2 mm E: 18.7 mm F: 8 mm H: 19 mm H1: 30 mm H2: 49 mm HW min.: −3 mm HW max.: 2.5 mm I: 10 mm K: 5.5 mm L1: 120 mm M: 18–21.5 mm N: 34 mm P: 34 mm Special features With horizontal foot Pressure screw M5 x 30 Size 1 Adjustable clamping range (C) Low-profile mounting for constrained spaces FAQ What clamping and holding forces does the clamp provide? The AMF Horizontal Clamp No. 6830 delivers a clamping force up to 800 N and a holding force up to 1,100 N, suitable for many light- to medium-duty fixture applications. Is the clamping range adjustable to accommodate different workpiece thicknesses? Yes, the clamp features an adjustable clamping range (C: 13–14.5 mm) and other dimensional allowances that enable adaptation to varying material thicknesses. Can the unit be mounted on horizontal surfaces with limited vertical clearance? The low-profile horizontal foot and compact Size 1 design permit mounting where vertical clearance is restricted, making the device suitable for confined fixture arrangements. Does the clamp include an adjustment screw and what is its specification? The assembly includes a pressure screw specified as M5 x 30 for contact-point adjustment and secure part seating within the fixture. Is the product identified by a specific SKU for ordering and traceability? Yes, the clamp is listed under SKU 4000833507NW for ordering and inventory control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
150mm Horizontal Clamp With Angle Base, Max Clamping Force 1200N, Max Thrust 1000N - AMF
The combination of a compact footprint, the angled foot and strong holding force ensures secure, repeatable clamping in constrained setups; the reliable clamping force reduces part movement and rejects downtime. Order the clamp directly via Metav Werkzeuge or consult our specialists for application-specific advice. Horizontal clamp Waagrechtspanner Nr.6833 Gr.2 with angled foot – AMF The Waagrechtspanner Nr.6833 Gr.2 is a size‑2 horizontal clamp with an angled foot, engineered for secure fixturing in assembly and machining environments. Horizontal clamp with angled foot Holding force up to 1,200 N Clamping force up to 1,000 N M6 x 35 pressure screw included Efficient, consistent clamping that reduces rework The clamp delivers a clear operational benefit by converting its rated clamping force of 1,000 N and holding force of 1,200 N into reliable part restraint. This performance level reduces micro‑movement during machining and assembly, helping to lower scrap rates and minimise rework. The measured forces indicate how much load the device applies and sustains: clamping force refers to the pressure applied to the workpiece, while holding force denotes the maximum retention under side loads. For production planning, these values provide an objective basis to compare fixtures and select the correct component for stable, measurable results. Space‑saving mounting and straightforward integration Fitted with an angled foot, the unit enables mounting on perpendicular or offset datum surfaces without complex adapters, simplifying fixture design and saving bench space. The supplied M6 x 35 pressure screw allows immediate installation into existing setups designed for metric fastenings. With a compact operational length (L1: 162 mm) and clearly defined heights (H: 73 mm, H1: 94 mm, H2: 68 mm), this clamp suits confined jigs where clearance is limited and repeatability is required. The compact geometry expedites integration into modular fixture systems and supports quick changeover between parts. Robust specification and clear numerical data for planners Design decisions benefit from explicit numerical specifications: many of the critical dimensions are recorded (for example, A: 6.2 mm, B: 52 mm, C: 20 mm, I: 13.2 mm) so engineers can model the clamp into CAD assemblies and confirm interference envelopes. The mechanical concept is intentionally straightforward, which minimises maintenance effort and simplifies spare‑part planning. Where higher‑level compatibility questions arise, the clear values allow process engineers to calculate clamping moments and verify that the device meets safety margins for specific operations. Contact Metav Werkzeuge for tailored fixture advice and secure supply of the AMF horizontal clamp — call +49 2822 7131930 or e‑mail info@metav-werkzeuge.com to discuss application requirements and delivery from Emmerich. Technical data Article number: 4123660120NW Type: 6833 Label: Waagrechtspanner Nr.6833 Gr.2 Winkelfuß AMF Product type: Horizontal clamp Execution: with angled foot Packaging unit: 1 Facts Max clamping force: 1,000 N Max holding force: 1,200 N Size: 2 A: 6.2 mm B: 52 mm C: 20 mm D: 5.6 mm E: 32 mm F: 10.5 mm H: 73 mm H1: 94 mm H2: 68 mm I: 13.2 mm K: 6 mm L1: 162 mm M: 25.5 mm N: 37 mm P: 32 mm a: 90° Special features With angled foot Pressure screw M6 x 35 Compact footprint for confined fixtures Clear dimensional data for CAD planning Brand: AMF FAQ What forces does the clamp provide and what do they mean? The clamp offers a clamping force of 1,000 N and a holding force of 1,200 N; clamping force is the applied pressure on the workpiece, while holding force is the maximum retention against lateral loads. Which mounting options are supported by the angled foot? The angled foot enables mounting on perpendicular or offset surfaces, allowing the clamp to be fixed where a straight base would not provide sufficient clearance. Is the pressure screw included and what size is it? A pressure screw M6 x 35 is included with the clamp for immediate installation into metric fixture systems. Can the clamp be modelled into existing CAD assemblies? Yes, the specification provides detailed dimensions (for example L1: 162 mm, H1: 94 mm) so engineers can place the component in CAD and verify clearances and interference. Is this clamp suitable for precision repeatability applications? The compact design and defined mechanical forces support repeatable positioning in assembly and light machining, reducing micro‑movement and improving process consistency. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
150mm Horizontal Clamp With Horizontal Base M8 x 65 Pressure Screw 3,000 N Clamping Force, 5,000 N Holding Force - AMF
Take advantage of a compact, fixture-ready design combined with reliable clamping performance: the horizontal foot execution and Size 5 configuration deliver a versatile mounting solution, while the 3,000 N pressing force and 5,000 N holding force guarantee secure workholding in repetitive operations. Order the clamp directly via Metav Werkzeuge or ask the consultancy team for application support. AMF Horizontal Clamp No. 6830, Size 5 — horizontal foot, 3 kN pressing force A horizontal clamp No. 6830 Size 5 for secure fixture clamping with a horizontal foot, intended for industrial workholding and repetitive machining setups Horizontal foot for fixed fixture mounting Max pressing force 3,000 N Holding force up to 5,000 N M8 x 65 clamping screw specification Secure clamping that improves cycle reliability The horizontal clamp delivers dependable clamping and retention for fixtures where consistent force matters. With a maximum pressing force of 3,000 N and a holding force of 5,000 N, the device is designed to maintain position under dynamic loads, which reduces part movement and rework. The compact Size 5 format and horizontal-foot execution mean it can be integrated into existing jigs and fixtures with minimal layout change, improving throughput without extensive redesign. Compact dimensions for straightforward integration Designed with precise dimensional data such as L1 321 mm, B 123 mm and an adjustable clamping height from +1.7 mm to 25 mm, the clamping range is clearly defined for planning and CAD integration. The unit is operated via an M8 x 65 clamping screw, a common thread size that simplifies replacement and maintenance. Where unfamiliar terms appear, the clamping range refers to the minimum and maximum height the clamp will secure, enabling correct part thickness planning without trial and error. Built for production environments and repetitive use The horizontal-foot configuration offers a low-profile mounting option that supports stable lateral load transfer during machining or assembly. Because the device is specified with numerical forces and dimensional references, it is suitable for fixture designers and production engineers seeking measurable, repeatable performance. The mechanical simplicity reduces setup time and the likelihood of functional faults in long production runs, supporting consistent output quality. Low-maintenance operation and predictable behaviour Operation is straightforward and is carried out with standard tools using the specified clamping screw; this keeps downtime low and maintenance simple. The clear numeric specifications allow process planners to calculate safety margins for clamping and to incorporate the clamp into automation sequences or manual fixtures. Documentation and parts lists can reference the No. 6830 identification for unambiguous ordering and replacement. For robust, measurable clamping in fixture builds, choose the AMF Horizontal Clamp No. 6830 Size 5 and contact Metav Werkzeuge for tailored mounting advice and supply from Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 4000833511NW Type: 6830 Designation: Horizontal clamp No. 6830, Size 5, horizontal foot (AMF) Execution: with horizontal foot Packaging unit: 1 Facts Max pressing force: 3,000 N Max holding force: 5,000 N Clamping height range: +1.7 mm to 25 mm L1: 321 mm A: 10 mm B: 123 mm C: 41.5 mm D: 8.5 mm E: 78 mm H: 46 mm H1: 73 mm H2: 128 mm Special features Size: 5 Clamping screw: M8 x 65 Execution detail: horizontal foot Additional dimension references included: F, I, K, L, L1, M, M1, N, P FAQ What clamping forces can be expected from this horizontal clamp? The AMF horizontal clamp No. 6830 (Size 5) provides a maximum pressing force of 3,000 N and a holding force of 5,000 N, suitable for secure fixturing in many production tasks. What is the adjustable clamping height of the clamp? The clamping height range for this model spans from +1.7 mm to 25 mm, which describes the minimum and maximum part thickness the clamp will accommodate. Which thread size is used for the clamping screw? The unit uses an M8 x 65 clamping screw specification, a common size that facilitates replacement and simplifies maintenance. Can the clamp be mounted in existing fixtures with limited space? The compact footprint, specified dimensions such as L1 321 mm and the horizontal-foot execution make the clamp suitable for integration into constrained fixture layouts. Is the product identified for unambiguous ordering? Yes, the clamp is listed as article number 4000833511NW, type 6830, which should be quoted when ordering or requesting spare parts. Manufacturer: AMF / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
150mm Horizontal Clamp With Horizontal Foot M4 x 25 Pressure Screw, 250 N Closing Force / 400 N Holding Force - AMF
Take advantage of a compact, low-profile clamping solution that combines reliable holding force and easy integration into jigs and fixtures. The clamp’s horizontal foot and measurable clamping values support consistent assembly throughput. Order the component directly via Metav Werkzeuge or consult our specialists for application advice. AMF Horizontal Toggle Clamp No. 6830, Size 0 – Horizontal Foot, 250 N Clamping Force The AMF Horizontal Toggle Clamp No. 6830 is a compact clamping device designed for fixtures and assembly applications, featuring a horizontal foot for low-profile mounting and reproducible clamping performance. Compact Size 0 for tight spaces Horizontal foot for low-profile mounting Clamping force 250 N for secure holding Holding force 400 N for reliable retention Efficient mounting for constrained fixtures The horizontal mounting design delivers a low-profile solution where vertical clearance is limited. Thanks to the horizontal foot arrangement and compact Size 0, the clamp slots into jigs and assemblies with minimal modification, reducing setup time and preserving workspace ergonomics. The incorporated M4 x 25 pressure screw permits simple pressure adjustment, enabling consistent contact pressure across repeated cycles and supporting predictable cycle times in batch production. Reproducible clamping and holding performance Measured values for clamping force (250 N) and holding force (400 N) provide a clear, quantifiable basis for fixture design decisions. These figures translate directly into predictable workpiece retention under lateral and axial process loads, lowering the risk of movement during machining or assembly. Specifying these forces early in the fixture design phase streamlines safety margins and helps avoid costly rework, while the toggle action ensures a secure mechanical lock without continuous external power. Simple integration and maintenance for long service life Integration into existing tooling is straightforward: the clamp’s footprint and key dimensions support standardised mounting and straightforward replacement if required. The horizontal foot facilitates a flush installation that keeps tooling envelopes compact, while the pressure screw enables on-site fine adjustments without special tools. Routine maintenance consists of quick visual checks and occasional lubrication of the joint areas to retain smooth operation and dependable clamping cycles. For ordering, technical matching or application support, contact Metav Werkzeuge GmbH—our consultants provide hands-on advice from the Emmerich site and can help select the right clamping configuration for the task at hand; eMail: info@metav-werkzeuge.com · Tel: +49 2822 7131930 Technical data Article number: 4000833506NW Type: 6830 Product: Horizontal clamp Execution: horizontal foot Brand: AMF Packaging unit: 1 Performance data Maximum clamping force: 250 N Maximum holding force: 400 N Pressure screw: M4 x 25 HW min.: -5.5 mm, HW max.: 0 mm Design & dimensions Size: 0 Key dimensions (mm): A 4 · B 28 · C 11.5–15.5 · D 4.6 · E 9 · F 5.5 Height values (mm): H 14.5 · H1 23 · H2 34 Length values (mm): L1 79 · M 16 · N 25 · P 25.5 FAQ What clamping and holding forces does this clamp provide? The clamp delivers a clamping force of 250 N and a holding force of 400 N, values indicated for reliable retention in fixture applications with moderate process loads. Is the clamp suitable for low-clearance installations? Yes, the horizontal foot and Size 0 format make it suitable for installations where vertical space is restricted and a low-profile mount is required. How is the clamping pressure adjusted? Clamping pressure is set using the supplied M4 x 25 pressure screw; fine adjustment allows reproducible contact pressure without specialised tools. Which dimensions are relevant for fixture layout? Key dimensions include A 4 mm, B 28 mm, C 11.5–15.5 mm and L1 79 mm; these values support precise positioning and repeatable mounting in jigs and fixtures. What material is the clamp made of and is surface coating specified? Material and coating are not specified in the provided data; for material confirmation and surface treatment options, Metav Werkzeuge can supply detailed information on request. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
150mm Horizontal Clamp With Horizontal Foot M6 x 35 Pressure Screw, 1,000 N Clamping Force - AMF
Take advantage of the combination of reliable clamping performance and a compact low-profile design for stable workholding in confined setups; order the unit via Metav Werkzeuge or contact our consultants for technical clarification. AMF Horizontal Clamp No. 6830, size 2 — horizontal foot, low-profile clamping The AMF Horizontal Clamp No. 6830 is a compact horizontal hold-down device designed for secure clamping in tight fixtures and machine setups, offering robust clamping and repeatable positioning for series production and toolroom use. Horizontal foot for low-profile clamping Clamping force up to 1,000 N Holding force max 1,200 N Robust clamping performance for repeatable production The clamp delivers a clamping force of 1,000 N and a holding force of 1,200 N, providing a reliable grip for short-cycle machining and assembly tasks. These figures translate into consistent part stabilisation during cutting, drilling or light milling operations, reducing positional variance and helping to maintain process tolerances. The force values are particularly relevant where repeatability is essential, because the device converts applied torque into a predictable axial hold that aids downstream quality control. Space-saving design that fits tight fixtures Equipped with a horizontal foot and configured as size 2, the clamp is built for low-profile placements where vertical space is limited. The compact footprint means the device integrates into dense fixture layouts without obstructing tool paths, enabling closer nestings of workpieces and more efficient use of clamping stations. The lower profile also minimises interference with tool holders and cutting trajectories, which helps to shorten setup times and increase machine utilisation. Straightforward adjustment and secure fixation Adjustment is achieved via the supplied pressure screw (M6 x 35), offering a simple mechanical interface for setting contact pressure and accommodating small height deviations within the specified range. The clamp’s adjustable stroke range supports fine tuning of clamping height so fixtures remain adaptable across different part geometries. This straightforward mechanism ensures quick repeat setups and reduces the need for extensive rework between batches. Practical benefits for workshop and small-series production The unit is engineered for ease of integration into jigs and fixtures, promoting fast assembly and long-term stability on the workbench or in CNC fixtures. Its measured specifications support reliable short-run production while maintaining flexibility for bespoke tasks. By choosing a compact horizontal solution, process planners gain a balance of accessibility and strength that supports efficient workflows and fewer handling delays. Secure the AMF Horizontal Clamp No. 6830 through Metav Werkzeuge; call +49 2822 7131930 or email info@metav-werkzeuge.com for tailored advice and prompt delivery from Emmerich. Technical data Article number: 4000833508NW Type: 6830 Product: Horizontal clamp Label: Waagrechtspanner Nr.6830 Gr.2 horizontal foot AMF Execution: with horizontal foot Packaging unit: 1 Core figures Clamping force max: 1,000 N Holding force max: 1,200 N Size: 2 Andrückschraube: M6 x 35 A [mm]: 6 B [mm]: 64 C [mm]: 26 D [mm]: 5.6 E [mm]: 32 F [mm]: 16 H [mm]: 24 H1 [mm]: 45 H2 [mm]: 68 HW min. [mm]: -1.5 HW max. [mm]: 5 I [mm]: 13.2 K [mm]: 6 L1 [mm]: 162 M [mm]: 19.5-29.5 N [mm]: 42 P [mm]: 38 Special features Horizontal foot for low-profile mounting Pressure screw M6 x 35 Size 2 configuration Manufacturer: AMF SKU: 4000833508NW FAQ What maximum clamping and holding forces are available? The AMF Horizontal Clamp No. 6830 provides a clamping force of up to 1,000 N and a holding force of up to 1,200 N, suitable for secure fixation in light to moderate machining tasks. How is the clamp adjusted for different part heights? Adjustment is made using the M6 x 35 pressure screw; the unit accommodates a height range with HW min. -1.5 mm and HW max. 5 mm and an M stroke range of 19.5–29.5 mm. Is the clamp suitable for tight fixture arrangements? Yes — the horizontal foot and size 2 configuration create a low-profile footprint designed to fit compact fixtures and dense nesting layouts. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
150mm Horizontal Clamp With Horizontal Foot M8×45 Pressure 1800N, Retention 2500N - AMF
Take advantage of a robust combination of holding force 2,500 N, clamping force 1,800 N and a compact Size 3 footprint to secure repeatable workholding in assembly and fixture applications; order the AMF horizontal clamp directly via Metav Werkzeuge or consult our team for application advice AMF Horizontal Clamp No. 6830 (Size 3) — horizontal foot, M8 x 45 pressure screw The AMF Horizontal Clamp No. 6830 (Size 3) is a compact horizontal-foot clamp designed for secure and repeatable workpiece holding in production fixtures and assembly stations. Horizontal foot for stable mounting Holding force up to 2,500 N Clamping force up to 1,800 N Size 3 with M8 x 45 pressure screw Secure clamping that speeds up production The horizontal clamp delivers a reliable holding force of 2,500 N and a clamping force of 1,800 N, values that translate directly into safer, more stable setups on jigs and fixtures. In practical terms, higher holding and clamping forces reduce micro‑movement during machining or assembly, so processes run with less scrap and fewer reworks. The labelled forces relate to peak capacities for fixture design and should be considered alongside the overall fixture rigidity and the chosen pressure screw. Compact design for straightforward integration Built with a horizontal foot, the device is tailored for easy mounting onto plates and tooling boards where space is limited. The clamp features an M8 x 45 pressure screw and an adjustable clamping range M 22–31.8 mm, enabling fine adjustment of the workpiece position without additional components. Such dimensions make the clamp suitable for short-stroke clamping tasks and tight pallet layouts; the compact profile supports efficient use of bench and fixture real estate while maintaining consistent performance. Stable repeatability for production and assembly For repetitive operations, repeatability and simple adjustment are essential. This clamp offers a predictable mechanical behaviour that assists in achieving consistent cycle-to-cycle results, especially in small-batch production and repair work. The combination of Size 3 geometry and the specified mechanical data ensures the device is appropriate for fixture builders seeking dependable clamping with straightforward set-up. Where process reliability is a priority, the clamp helps reduce downtime associated with repositioning and retightening. Contact Metav Werkzeuge today to discuss the AMF Horizontal Clamp No. 6830 and how its holding and clamping characteristics can be integrated into existing fixtures; technical advice and tailored recommendations are available from our Emmerich team Technical data SKU: 4000833509NW Type: 6830 Product: Horizontal clamp Brand: AMF Version: with horizontal foot Key measurements Size: 3 Max clamping force: 1,800 N Max holding force: 2,500 N Pressure screw: M8 x 45 Clamping range M: 22–31.8 mm L1: 206 mm H1: 48.5 mm H2: 86 mm HW min.: -2 mm HW max.: 9 mm Special features Horizontal foot for fixture mounting Packaging unit: 1 Compact footprint suitable for tight layouts Adjustable pressure screw for fine alignment FAQ What is the maximum holding force of this clamp? The AMF Horizontal Clamp No. 6830 provides a maximum holding force of 2,500 N, suitable for stable fixturing in many assembly and production contexts. How is the clamp mounted to a fixture plate? The clamp features a horizontal foot intended for mounting to fixture plates; the compact design of the AMF horizontal clamp simplifies plate integration and alignment. What adjustment options are available for different workpiece heights? Adjustment is achieved via the M8 x 45 pressure screw and the specified clamping range M 22–31.8 mm, allowing fine tuning of the workpiece position in the AMF clamp. Is the clamp suitable for use in small-batch production and repetitive assembly? Yes — the Size 3 geometry and specified force figures make the clamp a practical choice where repeatability and compact fixture design are required. Which SKU should be ordered for this model? Order SKU 4000833509NW for the AMF Horizontal Clamp No. 6830, Size 3 with horizontal foot. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
150mm Horizontal Clamp With Horizontal Foot, Clamping Screw M8×65, Max Thrust 2000 N, Max Holding 3000 N - AMF
Take advantage of the combination of reliable clamping forces and a compact footprint for efficient, repeatable workholding. The horizontal clamp Nr. 6830 (size 4) delivers consistent 2,000 N clamping force and up to 3,000 N holding force, enabling secure fixture in series production or workshop tasks — order via Metav Werkzeuge or consult our specialists for application support. Horizontal clamp Nr. 6830 (size 4) — horizontal foot, adjustable pressure screw (AMF) Horizontal clamp Nr. 6830 (size 4) is a robust horizontal clamp designed for low-profile mounting and secure workholding in industrial and workshop environments Horizontal foot for low-profile mounting 2,000 N clamping force, 3,000 N holding force Adjustable pressure screw M8 x 65 Size 4 with compact 287 mm length Secure, repeatable clamping for production The horizontal clamp provides defined mechanical clamping with a maximum clamping force of 2,000 N and a holding force of 3,000 N, offering consistent results in repetitive operations. The device uses an adjustable pressure screw M8 x 65, which enables fine setting of contact pressure; this is particularly useful when dealing with small tolerances or delicate components. Because the mechanism is a horizontal toggle-style fixture, it converts operator input into stable, locked clamping, reducing the risk of part movement during machining, inspection or assembly tasks. The clear numerical values for clamping and holding forces support process planning and risk assessment in production. Space-saving layout and straightforward integration With a compact L1 length of 287 mm and a dedicated horizontal foot, the clamp occupies minimal bench area while keeping the workpiece accessible. The adjustable clamping range M = 29–43 mm and the vertical working height window (HW min. −4 mm to HW max. 24 mm) permit flexible positioning across varied setups, reducing the need for additional adapters. Such a compact footprint simplifies fixture layouts on milling tables and assembly rigs, enabling denser workholding configurations without compromising accessibility. The concise dimensions facilitate CAD planning and quick verification against fixture templates. Practical handling and quick adjustment for workshop use The device is delivered with an integrated pressure screw and an uncomplicated mounting concept, enabling rapid installation and adjustment. The clamp’s geometry — including reference dimensions A = 10 mm, B = 113 mm and H1 = 75 mm — supports predictable clearance and alignment when combining with other fixtures. Because the mechanism locks positively, bench personnel benefit from a dependable tactile feedback during engagement and disengagement, which contributes to smoother cycle times and fewer reworks. The combination of robust mechanical locking and simple adjustment makes this clamp a pragmatic choice for repetitive production, jigs and manual assembly. For tailored advice on integrating the AMF horizontal clamp Nr. 6830 into specific fixtures or production cells, contact Metav Werkzeuge — call +49 2822 7131930 or email info@metav-werkzeuge.com to discuss compatibility and ordering options Technical data Article number: 4000833510NW Type: 6830 Brand: AMF Product: Horizontal clamp Execution: with horizontal foot Packaging unit: 1 Facts Maximum clamping force: 2,000 N Maximum holding force: 3,000 N Size: 4 Pressure screw: M8 x 65 Overall reference length L1: 287 mm Adjustable range M: 29–43 mm Special features Horizontal foot for low-profile mounting Adjustable pressure screw M8 x 65 Working height range HW min. −4 mm / HW max. 24 mm Reference dimensions for integration: A 10 mm, B 113 mm, H1 75 mm FAQ What is the maximum clamping force of this horizontal clamp? The AMF horizontal clamp Nr. 6830 has a maximum clamping force of 2,000 N and a maximum holding force of 3,000 N, suitable for many light to medium-duty workshop applications. Which adjustment range does the clamp offer for different workpieces? Adjustment is provided by the pressure screw M8 x 65 and the range M 29–43 mm; the working height window is HW min. −4 mm to HW max. 24 mm to accommodate varying part heights. Is the clamp suitable for low-profile mounting on fixture plates? Yes — the clamp features a horizontal foot and compact dimensions (L1 = 287 mm), specifically designed for low-profile bench or fixture-plate mounting. Can the clamp be combined with other fixtures in a modular system? The clamp’s defined reference dimensions (for example A = 10 mm, B = 113 mm) make layout planning straightforward and allow integration with common fixture elements and modular tooling. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
150mm Horizontal Clamp With Vertical Foot M5 x 30 Pressure Screw 800 N Holding 1100 N - AMF
Take advantage of the combination of compact design, reliable holding performance and straightforward integration into jigs and fixtures for uninterrupted production. The clamp’s vertical foot and clear adjustment range permit flexible mounting and exact workpiece positioning; contact Metav Werkzeuge for tailored advice or to place an order. AMF Horizontal clamp No. 6832 (Size 1) with vertical foot A AMF Horizontal clamp No. 6832 (Size 1) engineered for secure lateral clamping in fixtures and workholding, supplied with a vertical foot for flexible mounting in confined machine or bench setups Compact size 1 for tight fixtures Vertical foot for versatile mounting Max holding force 1,100 N Max clamping force 800 N Consistent clamping power for reliable machining The main benefit of this horizontal clamp is its consistent clamping force, specified at 800 N, combined with a holding force of 1,100 N. These values translate into stable fixation during milling, drilling or light turning operations, reducing the need for rework and improving cycle predictability. The difference between clamping and holding force is important: clamping force is the active pressure applied by the clamp, while holding force indicates the resistance against displacement once the workpiece is engaged. This distinction clarifies why the clamp maintains position under dynamic loads, delivering measurable efficiency gains and fewer interruptions in production. Space-saving mounting with the vertical foot Fitted with a vertical foot, the unit allows mounting where horizontal base access is restricted, making it suitable for tight jigs and modular fixture plates. The compact profile (notably L1 120 mm and H 31.5 mm) keeps the clamp's footprint small while offering an effective clamping width range (HW min. 8 mm to HW max. 15 mm). The integrated M5 x 30 pressure screw ensures fine adjustment of contact pressure without specialised tools, so set-up times are reduced. For workshops that prioritise floor space and quick reconfigurations, this design supports denser fixture layouts and faster changeovers. Simple integration and predictable handling Installation and maintenance are straightforward thanks to the clear mechanical features and standardised fastening. The clamp’s adjustment ranges (for example C 13–14.5 mm, M 23.5–25.5 mm) provide tangible reference points for fixture design and CAD planning, enabling immediate incorporation into existing tooling arrays. The robust mechanical concept offers repeatability across cycles, which supports quality assurance processes and reduces inspection workload. For procurement and engineering teams, the unit’s documented dimensions and forces simplify selection decisions and risk assessments in production planning. For reliable workholding choose the AMF Horizontal clamp No. 6832 from Metav Werkzeuge — contact Metav Werkzeuge for product advice and delivery from Emmerich via eMail info@metav-werkzeuge.com or phone +49 2822 7131930 Technical data Article number: 4123572110NW Type: 6832 Product: Horizontal clamp No. 6832, size 1, vertical foot Product type: Waagrechtspanner (Horizontal clamp) Execution: with vertical foot Manufacturer: AMF Packaging unit: 1 Core figures Max clamping force: 800 N Max holding force: 1,100 N A: 5 mm B: 42 mm C: 13–14.5 mm D: 5.2 mm E: 18.5 mm F: 8 mm H: 31.5 mm H1: 43 mm H2: 49 mm HW min.: 8 mm HW max.: 15 mm I: 10 mm K: 5.5 mm L1: 120 mm M: 23.5–25.5 mm M1: 24.5 mm N: 18 mm O: 5 mm Pressure screw: M5 x 30 Features and versions Size: 1 Vertical foot for alternative mounting orientation Standard pressure screw for simple adjustment Compact footprint for dense fixture layouts Supplied as single unit FAQ What clamping and holding forces does the AMF Horizontal clamp No. 6832 provide? The AMF Horizontal clamp No. 6832 offers a maximum clamping force of 800 N and a maximum holding force of 1,100 N, values that support stable workpiece fixation in many light- to medium-duty machining operations. How is the clamp mounted when it has a vertical foot? The vertical foot allows the clamp to be fastened on a vertical surface or fixture plate, so the clamp body operates horizontally while the mounting surface is vertical; this suits compact jigs and fixtures where base access is limited. Which adjustment range should be considered when planning a fixture? Use the effective clamping width range (HW min. 8 mm to HW max. 15 mm) and dimensions such as L1 120 mm and H 31.5 mm to ensure correct positioning and clearance in the fixture design. Is the pressure screw a standard size for easy replacement or adjustment? Yes; the unit uses an M5 x 30 pressure screw, a standard size that simplifies maintenance, replacements and procurement of spare parts. Can this clamp be used in automated fixtures or only for hand-set jigs? The mechanical characteristics and compact size of the clamp make it suitable for both manual jigs and semi-automated fixtures where mechanical actuation or external actuation systems interface with compact clamping elements. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
150mm Horizontal Clamp With Vertical Foot M6 x 35 Pressure Screw, 1,000 N Clamping Force - AMF
Take advantage of the combination of compact mounting, reliable hold and straightforward integration into fixtures to keep production stable; order the clamp directly via Metav Werkzeuge or consult our specialists for application advice. Horizontal clamp No. 6832, size 2 — horizontal clamp with vertical foot (AMF) The Horizontal clamp No. 6832, size 2 provides secure workholding with a vertical mounting foot for versatile fixture and jig applications in metalworking and general workshop environments. Vertical foot for secure mounting Clamping force 1,000 N Holding force 1,200 N Pressure screw M6 x 35 Compact size for tight fixtures Reliable hold for consistent machining results The clamp delivers a measurable clamping force of 1,000 N and a holding force rated to 1,200 N, values that ensure stable fixation during milling, drilling or light assembly tasks. These force ratings translate into fewer workpiece shifts and reduced rework; the result is higher throughput and predictable quality. The compact dimensions and defined stroke range allow integration into standard jigs and bespoke fixtures without compromising accessibility or tool paths. Flexible mounting and simple adjustment for workshop adaptability Equipped with a vertical foot, the device is designed for direct mounting on fixture plates or tooling blocks where a low-profile horizontal action is required. The built-in pressure screw M6 x 35 permits fine adjustment of the contact point, while the adjustable clamping range (M 29.5–34 mm) supports slightly varying workpiece heights. This combination of features reduces set-up time and simplifies repeatable positioning in series production or single-item jobs. Precise dimensions for predictable integration in assemblies A clear set of measured values supports design decisions when planning fixtures: key dimensions include L1 164 mm, B 64 mm and H1 61 mm, which help ensure predictable clearance and strike zones when multiple clamps are used in close proximity. The adjustable workpiece height span (HW min. 15 mm to HW max. 22 mm) provides the necessary tolerance for different setups while maintaining consistent clamping behaviour. Where reliable repeatability matters, these verifiable specifications make the component straightforward to specify in CAD and on the workshop floor. Contact Metav Werkzeuge today for tailored mounting guidance on the AMF horizontal clamp No. 6832 with vertical foot and secure the right configuration for the production task by emailing info@metav-werkzeuge.com or calling +49 2822 7131930 Technical data Article number: 4123572120NW Manufacturer: AMF Product type: Horizontal clamp (Waagrechtspanner) No. 6832 Execution: with vertical foot Packaging unit: 1 Facts Clamping force max: 1,000 N Holding force max: 1,200 N Size: 2 Pressure screw: M6 x 35 L1: 164 mm B: 64 mm H: 40 mm H1: 61 mm HW min: 15 mm HW max: 22 mm M: 29.5–34 mm A: 6 mm C: 26 mm E: 32 mm I: 13.2 mm Special features Vertical foot for direct plate mounting Compact footprint for tight setups Defined adjustment range for repeatability Suited for fixtures and jigs in metalworking Brand: AMF Type designation: 6832 SKU/UID: 4123572120NW FAQ What clamping and holding forces does the clamp provide? The clamp offers a clamping force of 1,000 N and a holding force of 1,200 N, providing a stable grip suitable for many fixture-based machining operations with the AMF horizontal clamp No. 6832. How is the clamp mounted in a fixture? Mounting is via the vertical foot, allowing direct attachment to fixture plates or tooling blocks; the compact design supports close spacing and multi-clamp arrangements. Which adjustment range is available for workpiece height? The unit accommodates an adjustable workpiece height from 15 mm to 22 mm, with a threaded adjustment range M 29.5–34 mm for precise setting. Is a special pressure screw required for operation? No special screw is required; the clamp uses a pressure screw M6 x 35 as standard for contact-point adjustment and secure pressure application. Can the clamp be specified directly by its dimensions for CAD integration? Yes, the clear dimensional data such as L1 164 mm, B 64 mm and H1 61 mm enable predictable CAD placement and collision checking when planning fixtures with the AMF horizontal clamp No. 6832. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
150mm Horizontal Clamp With Vertical Foot M8 x 45 Pressure Screw 1800N Holding Force 2500N - AMF
The combination of a vertical foot for lateral stability, an M8 x 45 clamping screw and a 2,500 N holding force delivers reliable locating and repeatable clamping in fixtures and jigs; ideal for short production runs and precise assembly tasks. Order the horizontal clamp directly via Metav Werkzeuge or request technical advice from the consultants if needed. Horizontal clamp No. 6832, Size 3 by AMF — vertical foot, M8 x 45 clamping screw The Horizontal clamp No. 6832, Size 3 is a compact workshop clamp with a vertical foot designed for firm lateral support and reliable holding in modular fixturing and bench fixtures. Robust vertical foot for secure clamping M8 x 45 clamping screw included Max holding force 2,500 N Size 3 with compact footprint Secure, repeatable clamping for reliable production The horizontal clamp offers consistent fixture performance thanks to a defined pressing characteristic and high holding capacity. With a 2,500 N holding force and a 1,800 N pressing force, the device is suited to tasks where parts must remain stationary under machining, assembly or inspection loads. The vertical foot increases lateral stability, reducing the risk of lateral movement during operations and therefore supporting reproducible results across multiple setups. For the production engineer, this means fewer rejects and reduced rework. Easy integration into jigs and modular fixtures Critical mounting and functional dimensions are provided to aid straightforward design integration. The clamp includes an M8 x 45 clamping screw, a clear overall length and adjustable range for the clamping jaw, enabling planners to calculate clearances and stroke without guesswork. The functional values specify the contact and travel ranges required for fixture layout, so the clamp can be incorporated into hydraulic-free, mechanically simple systems. For those less familiar with fixture design, holding force specifies the sustained retention under load, while pressing force refers to the initial clamp actuation capability. Practical use cases and workflow advantages Designed for fixture builders and maintenance technicians, the clamp performs well in assembly benches, small-batch machining fixtures and quality-control jigs. The compact footprint and defined height options allow denser station layouts and straightforward interchangeability, which shortens setup times and increases machine utilisation. Selected for robustness and straightforward mechanics, this clamp supports a pragmatic workshop approach: reliable clamping combined with low maintenance demand. For a tailored specification check or to secure reliable supply from Emmerich, request the AMF horizontal clamp No. 6832 through Metav Werkzeuge — technical consultants are available to confirm fit and fixture compatibility. Technical data Article number: 4123572130NW Type: 6832 Product: Horizontal clamp Version: with vertical foot Packaging unit: 1 Manufacturer: AMF Facts Max pressing force: 1,800 N Max holding force: 2,500 N Size: 3 Andrückschraube: M8 x 45 A: 8 mm B: 73 mm C: 25.7 mm D: 6.5 mm D1: 5.1 mm E: 38.5 mm F: 14 mm H: 49 mm H1: 65 mm H2: 86 mm HW min.: 14.5 mm HW max.: 26 mm I: 15 mm K: 7 mm L: 13 mm L1: 206 mm M: 37.5–42.5 mm M1: 42 mm N: 27 mm O: 6 mm Special features Vertical foot for lateral support M8 x 45 clamping screw included Compact design suitable for dense fixtures Label: Waagrechtspanner Nr.6832 Gr.3 senkrechter Fuß AMF Functional for jigs, fixtures and assembly benches FAQ What is the maximum holding force of the clamp? The clamp provides a maximum holding force of 2,500 N for the Horizontal clamp No. 6832, Size 3, ensuring secure retention during machining and assembly. Is the clamping screw supplied with the unit? Yes, the device is supplied with an M8 x 45 clamping screw as specified for the AMF horizontal clamp No. 6832. For which applications is this clamp most suitable? The clamp is intended for modular fixtures, jigs and assembly benches where a compact, mechanically reliable clamping solution is required; it suits short runs and repetitive positioning tasks. How does pressing force differ from holding force? Pressing force (1,800 N for this clamp) refers to the actuation or clamping action applied, while holding force (2,500 N) indicates the sustained retention under load once the workpiece is clamped. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
150mm Horizontal Clamp With Vertical Foot, Max Clamping Force 3,000 N, Max Actuation Force 2,000 N - AMF
Benefit from secure fixture and measurable clamping performance thanks to a 2,000 N pressing force and 3,000 N holding force, combined with a compact vertical foot and an adjustable M8 x 65 pressure screw for precise set-up — order the AMF horizontal clamp directly via Metav Werkzeuge or contact their consultants for procurement and technical advice. Horizontal clamp No. 6832, size 4, vertical foot (AMF) — robust clamping with defined forces The Horizontal clamp No. 6832 size 4 is a machine-fixture clamp with a vertical foot, designed for secure holding in machining and assembly jigs Vertical foot for compact mounting 2,000 N max pressing force 3,000 N max holding force M8 x 65 pressure screw included Precise clamping power for repeatable machining results The clamp delivers clearly specified forces: 2,000 N pressing force for actuation and 3,000 N holding force for static retention. These measurable values make process planning straightforward and reduce variability in setups. For production environments that require consistent cycle times and low scrap rates, a defined pressing value helps calculate required actuator sizes and cycle forces. The robust specification supports predictable fixture behaviour and contributes to improved machining accuracy and reduced rework. Space-saving mounting with a vertical foot for tight fixtures Thanks to its vertical foot, the clamp can be mounted in confined setups or on vertical plates without compromising accessibility. The compact layout and Size 4 designation mean the device fits medium-duty tooling stations and modular fixturing systems. Where bench space is limited or multiple clamps must sit closely together, the vertical-foot design minimises interference and enables denser, more efficient tooling arrangements while maintaining the same clamping performance. Simple adjustment and reliable actuation with standard components Adjustment is straightforward via the supplied M8 x 65 pressure screw, which allows fine setting of contact position and pressure. The clamp’s mechanical arrangement, including the documented adjustment range, supports quick calibration and reduces downtime during job changes. Standardised components such as an M8 pressure screw simplify maintenance and replacement, and make integration with existing fixturing hardware cost-effective and uncomplicated. Practical applications across machining and assembly tasks The clamp is suited to workshop and industrial jigs where secure, repeatable holding is required — for example on milling fixtures, drilling stations or light assembly lines. The clamping range 17.5–46 mm accommodates common workpiece heights and enables flexible use across a range of components. Its combination of robust holding capacity and compact mounting makes it a practical choice for toolrooms, subcontractors and production shops seeking dependable clamping without complex installation. Contact Metav Werkzeuge for procurement and personalised advice on the AMF horizontal clamp No. 6832 — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: 4123572140NW Type: 6832 Product: Horizontal clamp Execution: with vertical foot Manufacturer: AMF SKU: 4123572140NW Packaging unit: 1 Max pressing force: 2,000 N Max holding force: 3,000 N Facts A: 10 mm B: 113 mm C: 41 mm D / D1: 8.5 mm E: 63 mm F: 27 mm H: 66.5 mm H1: 97 mm H2: 115 mm HW min.: 17.5 mm HW max.: 46 mm I: 20 mm K: 8 mm L: 20.5 mm L1: 287 mm M: 52–59 mm M1: 59 mm N: 34 mm O: 8 mm Pressure screw: M8 x 65 Special features Vertical foot for compact installation Clamping range 17.5–46 mm Standard M8 pressure screw Size 4 designation for medium-duty fixtures Clear force specification for planning FAQ What is the maximum pressing force of the clamp? The clamp provides a maximum pressing force of 2,000 N, which is documented for process planning and actuator selection. What holding capacity can be expected once clamped? The device offers a 3,000 N holding force, ensuring secure retention during machining and light assembly operations. Is a pressure screw included and what is its specification? Yes, the unit includes a M8 x 65 pressure screw for adjustment of contact position and clamping pressure. What clamping range does the device cover? The clamp covers a clamping range of 17.5–46 mm, suitable for a wide range of workpiece heights in typical jig applications. Can the clamp be mounted on vertical plates or tight fixtures? The vertical foot design permits compact mounting on vertical plates and in densely populated fixturing setups. Which SKU should be referenced when ordering or enquiring? Reference SKU 4123572140NW and the horizontal clamp No. 6832 when requesting availability or technical details. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
20mm Horizontal Clamp Automatic Clamp Height Adjustment, 1,100 N - BESSEY
A compact solution combining automatic clamping height adjustment with a 1,100 N clamping force ensures fast, repeatable horizontal fixation and reduced setup time; order the BESSEY STC-HH20 directly via Metav Werkzeuge or consult the technical team for application support. BESSEY STC-HH20 Horizontal Clamp (Size 20) — Automatic Height Adjustment, 1,100 N The BESSEY STC-HH20 Horizontal Clamp offers robust horizontal clamping on a dedicated base plate, optimised for repeatability and short cycle times in workshop and production environments Automatic clamping height adjustment Max. clamping force 1,100 N Size 20 with 167 mm jaw length Adjustable spindle range 26–31.75 mm Consistent clamping that cuts cycle time The combination of automatic clamping height adjustment and a rated 1,100 N clamping force delivers dependable holding power with minimal operator intervention. Automatic height compensation reduces the need for manual readjustment when part thickness varies, so set-up errors and rework are lowered and fixture throughput is improved. Efficiency gains arise from fewer handling steps and from the clamp's ability to maintain consistent pressure across repetitive cycles, which is especially beneficial in medium-volume production and jigs where repeatability matters. Compact dimensions for flexible fixture design Designed as a horizontal base-plate clamp, the unit features a jaw length of 167 mm (L1) and an adjustable spindle range of 26–31.75 mm (M), enabling secure positioning across a variety of workpiece profiles. Additional measured points — A 10 mm, B 45 mm, C 13 mm, E 20 mm, H1 25 mm, I 10 mm, N 42 mm, P 45 mm — support precise planning when integrating the clamp into existing tooling. The modest footprint and clearly defined dimensions make the device straightforward to implement on modular tooling boards and bespoke fixtures, allowing engineers to predict spatial requirements and ensure reliable clearance for adjacent operations. Built for workshop reliability and straightforward integration Manufactured by BESSEY, this horizontal clamp is intended for frequent use in both trade workshops and light industrial settings where dependable clamping and rapid turnaround are required. The mechanism is engineered for low maintenance and long service life; routine checks and lubrication prolong operational performance. Its horizontal base-plate format facilitates mounting in standard fixture layouts and supports modular assembly processes. As a component in an optimised workholding strategy, the clamp contributes to reduced cycle variation and improved downstream quality outcomes. Contact Metav Werkzeuge to discuss deployment of the BESSEY STC-HH20 for specific fixtures, request a quotation or obtain detailed technical drawings — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 4000831133NW Type: STC-HH Product: Horizontal clamp Brand: BESSEY Execution: automatic clamping height adjustment Packaging unit: 1 Facts Max. clamping force: 1,100 N L1 (jaw length): 167 mm M (adjustable spindle range): 26–31.75 mm A: 10 mm B: 45 mm C: 13 mm E: 20 mm H1: 25 mm I: 10 mm N: 42 mm P: 45 mm Special features Automatic clamping height adjustment Horizontal base plate version Size: 20 FAQ What is the maximum clamping force of the clamp? The clamp provides a maximum clamping force of 1,100 N, as specified for the BESSEY STC-HH20. Which dimensions are relevant for fixture design? Key dimensions for fixture planning include the jaw length L1 = 167 mm and the adjustable spindle range M = 26–31.75 mm; further dimensional data (A, B, C, E, H1, I, N, P) are available in the technical data. Is the height adjustment automatic or manual? The STC-HH20 features automatic clamping height adjustment, enabling compensation for varying part heights without manual re-setting. Can the clamp be mounted on a modular fixture plate? Yes, the horizontal base-plate design of the STC-HH20 is compatible with standard modular fixture arrangements and can be integrated into existing workholding systems. Which brand manufactures this horizontal clamp and what is the article number? This horizontal clamp is manufactured by BESSEY and is listed under article number 4000831133NW. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
20mm Horizontal Clamp Variable Open Holding Arm Angle Base M6 x 40 Pressure Screw, Max 2000 N - AMF
Reliable clamping with a variable open holding arm and angled base enables secure, repeatable workholding and rapid set-up; combined with automatic height compensation and a 2,000 N maximum clamping force this results in stable machining and less rework — order the horizontal clamp directly via Metav Werkzeuge or ask our consultants if needed. AMF Horizontal Clamp No. 6871, Size 20 — Angle Base, Variable Open Holding Arm The AMF Horizontal Clamp No. 6871, Size 20, Angle Base is a compact horizontal clamp for secure workholding in machining and assembly applications, featuring a variable open holding arm and an angled base for flexible mounting. Variable open holding arm for versatile use Angle base for flexible mounting options Automatic height compensation 20–35 mm Max. clamping force 2,000 N Secure and consistent workholding for production use This horizontal clamping solution offers repeatable clamping thanks to its robust kinematics and a specified maximum clamping force of 2,000 N, which ensures components remain stationary during machining or assembly. The design includes a variable open holding arm, enabling quick positioning of irregular or bulky parts without complex adjustment. Built-in adjustability reduces set-up time and helps maintain consistent cycle times on the shop floor. Rapid height adjustment reduces set-up complexity Featuring automatic height compensation (S = 20 mm) and a maximum compensating range of 35 mm, the device adapts to slight differences in workpiece height without manual shimming. This automatic compensation minimises the need for re-clamping and supports continuous operation across batches with variable stock thickness. The integrated pressure screw (M6 x 40) provides controlled actuation and reliable pressure application for repeatable results. Compact angle base for flexible fixture construction The angled base provides multiple mounting orientations, making it straightforward to integrate into custom fixtures or modular tooling plates. With a total length (L1) of 173 mm and defined interface dimensions such as B = 56 mm and E = 22 mm, the clamp fits tight assemblies while offering sufficient reach and clearance. The open holding arm configuration supports quick loading and unloading, improving throughput in assembly and inspection stations. Practical adjustment range and workshop durability Key adjustment values such as the clamping jaw range (C = 20–26 mm) and work height limits (HW min. -3 mm / HW max. 24 mm) make it simple to determine suitability for specific parts. The unit’s compact form and clearly defined interface dimensions facilitate predictable integration into existing tooling. With a packaging unit of 1, the product is delivered ready for installation in single-piece applications or as a spare part for maintenance. Contact Metav Werkzeuge today to discuss integration options for this AMF horizontal clamp and secure reliable, precision workholding for your production line Technical Data Article number: 4123572011NW Type: 6871 Product label: Waagrechtspanner Nr.6871 Gr.20 Winkelfuß AMF Facts Clamping force, max: 2,000 N Automatic height compensation S: 20 mm Max. height compensation: 35 mm C (clamping range): 20–26 mm B: 56 mm L1: 173 mm H: 68 mm H1: 94 mm H2: 113 mm D / D1: 5.6 mm A: 6 mm E: 22 mm F: 24 mm I: 10 mm K: 7.1 mm M: 25.4 mm N: 45 mm P: 38 mm HW min.: -3 mm HW max.: 24 mm Pressure screw: M6 x 40 Packaging unit: 1 Special features Variable execution; open holding arm; angled base Automatic height compensation Compact dimensions for tight fixtures Designed for machining and assembly workholding FAQ What is the maximum clamping force of this clamp? The clamp delivers a maximum clamping force of 2,000 N, which ensures secure fixation for typical machining and assembly tasks with the AMF Horizontal Clamp No. 6871, Size 20. How much height compensation is available? Automatic height compensation is 20 mm, with a maximum compensating range of 35 mm, allowing the clamp to accommodate small variations in workpiece height without manual shimming. Which clamping range does the device support? The clamping jaw range is 20–26 mm (C), suitable for many small to medium-sized components used in fixtures. Is the angled base suitable for modular fixture plates? Yes, the angle base permits flexible mounting orientations and straightforward integration into modular tooling plates or custom fixtures. What mounting and interface dimensions are specified for integration? Key interface dimensions include L1 = 173 mm, B = 56 mm, E = 22 mm, and hole diameters D / D1 = 5.6 mm, enabling predictable installation in existing setups. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
50mm Horizontal Clamp With Angle Base Variable Open Holding Arm, M8×55 Pressure Screw, 3000N - AMF
Take advantage of the combination of high clamping force, flexible mounting and automatic height compensation for reliable fixture performance; order the unit via Metav Werkzeuge or contact our consultants for specification support. Horizontal clamp No. 6871 (Size 50) – angled foot, 3,000 N clamping force | AMF A Horizontal clamp No. 6871 for secure hold-down in fixture and jig applications, offering a variable open holding arm and an angled foot for versatile mounting in machining setups. 3000 N maximum clamping force Variable open holding arm Automatic height compensation 35–40 mm Angled foot for flexible mounting Accurate clamping that maintains process stability The clamp delivers a maximum clamping force of 3,000 N, ensuring steady workpiece fixation under typical machining loads. The benefit is a measurable reduction in micro-movement during milling and drilling, which translates into repeatable tolerances and fewer rejects. The design focuses on functional reliability: the core mechanism provides consistent pressure while the compact footprint preserves access to the workpiece. This makes the clamp suitable for production jigs and small-batch fixtures where stability and throughput are priorities. Flexible mounting and straightforward height compensation Installation is simplified by the angled foot and the automatic height compensation of 35–40 mm, allowing the clamp to adapt to slight variations in workpiece height without manual shimming. The unit includes an M8 x 55 clamping screw and a range of dimensional references (for example A = 8.4 mm, B = 85 mm, C = 22–32 mm) that enable precise positioning in fixture plates. This flexibility reduces set-up time and supports quicker changeovers between components, improving overall machine utilisation and workflow efficiency. Open holding arm design for accessible workpiece loading The variable open holding arm facilitates easy loading and unloading of parts while maintaining a secure hold during machining. By combining accessibility with a robust hold-down function, the clamp reduces handling time and minimises the risk of collision with tooling. The adjustable clamping range (HW min. 1 mm to HW max. 31 mm) covers a wide span of part geometries, making the device a practical choice for mixed-production environments where adaptability matters. Durable construction for dependable everyday use Built for routine shop-floor conditions, the clamp is engineered for longevity and low maintenance. Key functional elements such as the automatic compensating mechanism and the solid clamping interface are designed to withstand repeated cycles without loss of performance. The clear numerical specifications and simple mechanical concept support predictable maintenance planning, which contributes to uninterrupted production and reliable throughput over time. For secure procurement and fast, reliable delivery, order the AMF Horizontal clamp No. 6871 via Metav Werkzeuge — technical consultants are available at info@metav-werkzeuge.com or by phone on +49 2822 7131930 to confirm suitability for the intended application Technical data Article number: 4123572012NW Type: 6871 Name: Horizontal clamp No. 6871 Size 50, angled foot (AMF) Product type: Horizontal clamp Manufacturer: AMF Packaging unit: 1 Facts Maximum clamping force: 3000 N A: 8.4 mm B: 85 mm C: 22–32 mm D / D1: 6.5 mm E: 35 mm F: 37 mm H: 88 mm H1: 124 mm H2: 158 mm HW min.: 1 mm HW max.: 31 mm I: 13 mm K: 10.6 mm L1: 244 mm M: 38.1 mm N: 57 mm P: 51 mm Automatic height compensation S: 35 mm Maximum height compensation: 40 mm Clamping screw: M8 x 55 Special features Variable execution; open holding arm; angled foot Size: 50 Designed for fixture and jig clamping applications Compact footprint with high clamping capability Clear dimensional references for accurate integration FAQ What clamping force does this device provide? The clamp provides a maximum clamping force of 3,000 N, making the AMF Horizontal clamp No. 6871 suitable for standard machining fixture duties. How much height variation can the clamp compensate for? The unit features automatic height compensation with an effective S of 35 mm and a maximum compensation of 40 mm, enabling adaptation to small workpiece height differences. Which clamping range is supported by the holding arm? The adjustable clamping range is from HW min. 1 mm to HW max. 31 mm, allowing the clamp to secure a variety of part thicknesses in production jigs. Which mounting and fixing elements are included in the specification? Dimensional details include an M8 x 55 clamping screw and multiple reference measurements (for example L1 = 244 mm, H = 88 mm) to assist correct fixture integration for the Horizontal clamp No. 6871 (AMF), SKU 4123572012NW. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
50mm Horizontal Clamp With Automatic Height Adjustment, 2.5 kN Clamping Force, Group 50 - BESSEY
Combining automatic height compensation with a reliable 2,500 N clamping force ensures repeatable, secure holds and a smooth workflow in batch and one-off machining. Benefit from robust horizontal support and straightforward integration in existing jigs; order directly via Metav Werkzeuge or consult our specialists for application advice. STC-HH50 horizontal clamp (size 50) — BESSEY STC-HH50 is a horizontal clamp designed for workshop and industrial fixturing, offering automatic clamping height adjustment and a compact horizontal base plate for secure workholding. Automatic clamping height adjustment 2,500 N maximum clamping force Horizontal base plate design Compact size 50 for flexible fixturing Consistent performance through controlled clamping force The unit delivers a 2,500 N clamping force, which provides a clear, measurable parameter for process planning and fixture design. This defined force reduces variability between cycles and supports predictable machining results. The automatic height adjustment mechanism converts uneven workpiece heights into consistent clamp pressure, reducing set-up time and lowering the risk of over‑ or under‑clamping. Such repeatability benefits production lines and manual workshops seeking efficient, reliable workholding. Space-saving design with precise dimensional data The compact construction and horizontal base plate optimise bench and fixture space. Key dimensions — L1 217 mm, M 33–48 mm and A 13 mm — permit easy integration into existing clamping systems and bespoke jigs. These metrics allow planners to calculate clearances and stroke requirements without guesswork. The practical size classification (size 50) indicates the clamp’s intended duty range, making specification straightforward when comparing alternatives for a given application. Practical advantages for workshop and industrial use Built for routine use, the clamp suits repetitive assembly, light machining and general fixturing tasks where a dependable horizontal hold is required. The automatic height compensation shortens set-up for varied stock thicknesses, while the horizontal orientation stabilises flat and prismatic parts during operations. Supplied as a single unit, the device supports modular fixture concepts and rapid changeovers, improving throughput and reducing fixture complexity. Contact Metav Werkzeuge for detailed application support and fast procurement of BESSEY horizontal clamps; our specialists at Metav Werkzeuge can advise on best practices and supply from stock. Technical data Article number: 4000831134NW Type: STC-HH Label: Waagrechtspanner STC-HH50 Gr.50 waagrechte Grundpl. BESSEY Manufacturer: BESSEY Packaging unit: 1 Core specifications Max clamping force: 2,500 N Size: 50 L1: 217 mm M: 33–48 mm A: 13 mm B: 77 mm C: 25.4 mm E: 40 mm H1: 27 mm I: 14 mm N: 60 mm P: 53 mm Features and applications Automatic clamping height adjustment Horizontal base plate design Suitable for workshop and industrial fixturing Supplied as single unit FAQ What is the maximum clamping force of this horizontal clamp? The BESSEY STC-HH50 horizontal clamp provides a maximum clamping force of 2,500 N, suitable for secure holding in many workshop and light industrial applications. How does the automatic height adjustment benefit set-up times? The automatic clamping height adjustment on the STC-HH50 compensates for variations in stock thickness, reducing manual shimming and accelerating fixture set-up for repeatable cycles. Which dimensions are most relevant for integrating the clamp into a jig? Key dimensions to consider are L1 217 mm and M 33–48 mm, together with A, B and C (shown in the technical data), which define mounting space and effective stroke for the clamp. Is the clamp delivered ready for immediate installation? The STC-HH50 is supplied as a single unit; mounting and installation depend on the chosen fixture design and any additional fasteners or adaptors required for the specific setup. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
70mm Horizontal Clamp With Angle Base Size 3 M8x45 Pressure 1800N Holding 2500N - AMF
Take advantage of a compact, flexible clamping solution that combines a right-angled mounting foot with a size 3 form factor and clear force ratings; the combination of 1,800 N max clamping force and 2,500 N holding force ensures secure workholding for light to medium machining tasks. Order the horizontal clamp directly via Metav Werkzeuge or ask our consultants if needed. Horizontal clamp No. 6833, size 3, angled foot (AMF) — robust clamping with 1,800 N clamping force The Horizontal clamp No. 6833, size 3, angled foot (AMF) is a compact horizontal workholder designed for fixture plates and machine tables where angled mounting improves accessibility and setup flexibility Size 3 with angled foot Max clamping force 1,800 N Holding force up to 2,500 N Secure, measurable clamping for repeatable production The clamp delivers clearly defined performance: a maximum clamping force of 1,800 N for active clamping operations and a holding force of 2,500 N for static retention. These figures provide a reliable basis for process planning and tool-path strategy, allowing production engineers to calculate fixture loads and select suitable cutting data. The rated forces are particularly important in jigs for milling and drilling where consistent contact pressure reduces part movement and improves dimensional repeatability. The specified values help avoid guesswork and support predictable cycle times. Flexible mounting and practical dimensions for compact fixtures Fitted with an angled foot, the clamp adapts to tight layouts and angled fixturing without additional brackets. The integrated pressing screw M8 x 45 and a clear overall length L1 206 mm enable straightforward installation on T-slots and fixture plates. The right-angled base reduces horizontal space while providing a stable bearing surface, which simplifies set-up for small-batch production and repair work. The clamp’s geometry supports quick positioning and alignment, reducing non-productive time during changeovers. Practical robustness for workshop and small-series applications Designed as a purpose-built horizontal workholder, the component balances compactness with stable retention. The sturdy construction that yields high holding capacity is suitable for assembly stations and machining centres handling light to medium workpieces. Maintenance is minimal: the simple mechanical design limits wear parts to the pressing screw and contact surfaces, allowing long service intervals and uncomplicated replacement procedures. This makes the clamp a practical choice for workshops seeking dependable, low-maintenance fixturing. Contact Metav Werkzeuge for tailored advice on integrating the AMF horizontal clamp No. 6833 into existing fixtures, with fast supply from Emmerich — phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data Article number: 4123660130NW Type: 6833 Label: Waagrechtspanner Nr.6833 Gr.3 Winkelfuß AMF Manufacturer: AMF Packaging unit: 1 Facts Max clamping force: 1,800 N Max holding force: 2,500 N Size: 3 Pressing screw: M8 x 45 Overall length L1: 206 mm H: 70 mm; H1: 86.5 mm; H2: 86 mm Special features Angled foot for right-angled mounting Angle a: 90° A: 8 mm; B: 59 mm; C: 24 mm; D: 6.8 mm; E: 37 mm; F: 6.5 mm I: 15 mm; K: 7 mm; M: 28.5 mm; N: 42.5 mm; P: 38 mm FAQ What clamping and holding forces can be expected from this clamp? The AMF horizontal clamp No. 6833 (SKU 4123660130NW) provides a maximum clamping force of 1,800 N and a holding force of up to 2,500 N for secure retention during machining. Is the clamp suitable for mounting on fixture plates with T-slots? Yes, the angled foot and the overall length of 206 mm make the clamp compatible with common fixture plates and T-slot arrangements when combined with the M8 x 45 pressing screw. Which applications suit this horizontal clamp best? The clamp is well suited to small-series machining, assembly stations and jigs where compact, repeatable clamping and easy access are required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
70mm Horizontal Clamp With Automatic Height Adjustment, 2.5kN Clamping Force, 217mm Reach - BESSEY
Combining automatic clamping-height adjustment with a stable horizontal base plate and a max. clamping force of 2,500 N, this clamp secures varying workpiece thicknesses quickly and reliably; ideal for jigs and fixture use in production and workshops. Order the clamp directly via Metav Werkzeuge or consult the technical team for application support. BESSEY STC-HH70 Horizontal clamp – Automatic height adjustment, horizontal base plate The STC-HH70 is a horizontal hold-down clamp designed for jigs, fixtures and general workshop use, offering automatic clamping-height adjustment to accommodate variable material thickness. Automatic clamping-height adjustment Horizontal base plate for stable mounting Max. clamping force 2,500 N Compact size 70 with 217 mm reach Faster, more reliable clamping for mixed production The combination of automatic clamping-height adjustment and a max. clamping force of 2,500 N delivers consistent results across mixed batches and single-part operations. The height compensation prevents overtravel and reduces setup time by absorbing variations in workpiece thickness without manual intervention. For production planners, this means fewer stoppages for re‑adjustment and a measurable improvement in cycle reliability. The clamp is particularly suited to repetitive holding tasks where repeatability and steady clamping pressure matter. Simple integration and stable mounting reduce downtime Fitted with a horizontal base plate, the unit provides a firm mounting interface for fixture plates and assembly jigs. The 217 mm reach (L1) and compact footprint allow positioning close to the work area while maintaining clearance for tooling. Clear dimensional data (A, B, C, E, H1, I, M, N, P) support precise layout planning and ensure compatibility with existing fixtures. The clamp’s design reduces the need for custom adaptors and speeds up commissioning in both small workshops and production lines. Practical benefits for workshop and industrial use Constructed for everyday workshop conditions, this horizontal hold-down solution suits metalworking, assembly and fixture building where predictable clamping is required. The automatic adjustment protects delicate components from excessive force while still enabling high holding power when needed, improving handling safety and part integrity. With its compact size and stable mounting, the clamp aids ergonomic workbench design and contributes to a tidier, more efficient workflow. Contact Metav Werkzeuge for tailored application advice or to request a technical quote for the BESSEY STC-HH70; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 4000831135NW Model: STC-HH Label: Waagrechtspanner STC-HH70 Gr.70 waagrechte Grundpl.BESSEY Product type: Horizontal clamp Execution: automatic clamping-height adjustment Packaging unit: 1 Manufacturer: BESSEY UID: 4000831135NW Facts Max. clamping force: 2,500 N Size: 70 A: 13 mm B: 77 mm C: 25.4 mm E: 40 mm H1: 44 mm I: 14 mm L1: 217 mm M: 33–48 mm N: 60 mm P: 53 mm Special features Automatic clamping-height adjustment Horizontal base plate Compact design for tight layouts Suitable for jigs and fixtures Stable, repeatable holding force FAQ What is the maximum clamping force of this clamp? The BESSEY STC-HH70 horizontal clamp provides a maximum clamping force of 2,500 N, suitable for secure holding in many workshop and light industrial applications. How does the automatic clamping-height adjustment work? The clamp’s automatic height adjustment compensates for variations in workpiece thickness, allowing controlled travel and consistent clamping pressure without manual re‑setting, which speeds up setup and reduces errors. Which dimensions are most relevant for planning a fixture? Key dimensions include the 217 mm reach (L1) and the adjustment range M: 33–48 mm; the full set of measurements (A, B, C, E, H1, I, N, P) supports precise fixture layout and alignment. Is the clamp suitable for use in production jigs and assembly lines? Yes. The horizontal hold-down design and stable base plate make it well suited for jigs, fixtures and repetitive assembly tasks where fast, repeatable clamping is required. Does the clamp require special mounting hardware? The base plate provides a standard mounting surface for direct attachment to fixture plates; any additional adapters depend on the individual jig design rather than on the clamp itself. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Waagrechtniederzugspanner MFT f.Bohr-D.20mm BESSEY
zum Einsatz auf Multifunktionstischen mit Lochdurchmesser 20 mm und Plattenstärke von min. 19 mm · patentierter Niederzugmechanismus verhindert, dass sich das Werkstück beim Spannen von der Tischfläche abhebt – auch ohne Befestigungsschraube · schnelle Fixierung dank seitlich platziertem Spannhebel · ermöglicht vollflächige Bearbeitung des Werkstücks – auch runder und flacher Teile
Waagrechtspanner 1xSTC-HH50+1xSTC-SET-T20 BESSEY
zum Einsatz von BESSEY Schnellspannern auf Multifunktionstischen wie z.B. Festool MFT und Sortimo WorkMo mit Lochdurchmesser 20 mm und Plattenstärke von min. 19 mm bis max. 25 mm
Waagrechtspanner 1xSTC-HH70+1xSTC-SET-T20 BESSEY
zum Einsatz von BESSEY Schnellspannern auf Multifunktionstischen wie z.B. Festool MFT und Sortimo WorkMo mit Lochdurchmesser 20 mm und Plattenstärke von min. 19 mm bis max. 25 mm
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com