112mm Quick-Change Tool Holder Head D1 With Eccentric Clamp, Hardened 40-Tooth 9° Indexing - TECWERK
Benefit from rapid tool changes, secure eccentric clamping and a proven 0.01 mm repeatability for stable, high-throughput machining. The hardened and ground contact surfaces extend service life while 40 indexing positions allow fast retooling at 9° increments — order directly via Metav Werkzeuge or consult our specialists for application-specific advice. TECWERK Quick-change Toolholder Head Gr. D1 — 40-position indexing, 40 mm bore A TECWERK Quick-change Toolholder Head Gr. D1 designed for fast swaps of cutting tools in lathe and CNC toolpost systems, featuring eccentric clamping and industrial-grade repeatability. Eccentric clamp for secure rapid tool change Repeatability to 0.01 mm for consistent results 40-position indexing with 9° increments Hardened, ground gear and contact surfaces Reduce downtime with faster, repeatable tool changes The quick-change head uses an eccentric clamping mechanism to lock cutters reliably, enabling significantly reduced tool-change time compared with conventional fixtures. Because the system delivers a repeatability of 0.01 mm, process variation is minimised and set-up time for recurring operations is cut. Eccentric clamping converts a short lever action into strong radial force, so the head holds the cutting insert or holder firmly without complex tightening sequences — a practical advantage on busy turning centres and manual lathes where cycle time matters. Flexible indexing and precise height adjustment for versatile set-ups With 40 teeth in the indexing ring, each position corresponds to a 9° increment, allowing a wide range of tool angles without disassembly. The central bore of 40 mm accepts the mounting body, and three maximum overhang options (112 / 116 / 124 mm) permit selection according to reach and rigidity requirements. Tip height is set via a dedicated adjustment screw on the toolholder, which simplifies achieving correct centre height and avoids repeated scraping or shimming — an essential feature for shops that switch between facing, turning and profiling operations. Hardened components for durable accuracy and low maintenance The gearing and mating contact faces are hardened and ground, ensuring long-term resistance to wear and preserving datum accuracy even under repetitive indexing cycles. This construction reduces the need for frequent regrinding or replacement, supporting predictable maintenance intervals and lower lifetime cost of ownership. Built to integrate into workshop tool systems, the head is suited for demanding production environments where repeatable alignment and robust clamping determine part quality and process stability. For tailored advice on selecting the right TECWERK quick-change head for specific machines and to arrange supply from Metav Werkzeuge in Emmerich, contact info@metav-werkzeuge.com or call +49 2822 7131930 for expert support. Technical Data Article number: 2000832154NW Type: D1 Designation: Quick-change toolholder head Gr. D1 Brand: TECWERK Facts Bore diameter: 40 mm Index positions: 40 Index increment: 9° Repeatability: 0.01 mm Maximum overhang: 112 / 116 / 124 mm Packaging unit: 1 Special features Eccentric clamping for rapid tool changes Tip height adjustable via set screw at the holder Hardened and ground gear and contact surfaces 40-position indexing for multiple tool angles FAQ Is the quick-change head compatible with standard toolposts? Compatibility depends on the toolpost and mounting body interface; the TECWERK Quick-change Toolholder Head Gr. D1 is designed around a 40 mm bore and common D1-type interfaces, so matching the mounting shank or adapter is required for direct fitment. How precise is the indexing and how is it achieved? Indexing is achieved by a 40-tooth ring giving 9° increments; the mechanism provides secured positions and, together with the hardened contact faces, supports the stated 0.01 mm repeatability during re-clamping. Can the tip height be fine-tuned after installation? Yes, the tip height on the quick-change holder is adjusted by a set screw on the toolholder, enabling fine height correction without removing the head from the machine. What are the implications of the different maximum overhangs? Choosing between 112, 116 or 124 mm overhang balances reach against rigidity: shorter overhangs improve stiffness and reduce deflection, while longer overhangs permit greater access to larger workpieces. Is the head suitable for heavy-duty production use? The hardened, ground gear and main contact surfaces are specified for extended wear resistance, making the head well suited to repetitive production tasks where durable accuracy is required. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
120mm Toolholder For Steel Holder Head B With 40mm Cylindrical Bore, Quick-Change Compatible - TECWERK
Benefit from the robust quick-change design with a 40 mm cylindrical bore and a 120 mm overall length for reliable clamping and faster setup cycles; order the holder directly via Metav Werkzeuge or consult the team for application-specific advice. TECWERK Quick-change holder (for Steel Holder Head B) — 40 mm cylindrical bore, 120 mm length The TECWERK Quick-change holder (for Steel Holder Head B) is a precision clamping component designed to receive large boring bars and Morse taper sleeves directly for turning and boring operations 40 mm cylindrical bore for large shanks Direct mounting for big boring bars and MT sleeves 120 mm overall length for stable engagement Faster changeovers with proven repeatability The quick-change concept reduces machine downtime by enabling fast, repeatable swaps between tools. With a 40 mm cylindrical bore and an overall 120 mm length, the unit provides a consistent seating surface that maintains concentricity and minimises run-out during operations. In practice, this translates into shorter setup times and fewer re-measurements after tool changes, supporting lean production goals and higher machine utilisation. Designed for heavy boring bars and Morse taper sleeves Engineered for the direct acceptance of large boring bars and Morse taper sleeves, the holder offers the rigidity required for medium- to heavy-duty turning tasks. The cylindrical reception ensures an even load distribution along the shank, which improves cutting stability and surface finish. For users with mixed tooling—solid bars and MT-mounted tools—this reduces the need for additional adapters and simplifies tooling logistics. Built compatibility with Steel Holder Head B for straightforward integration The interchangeable unit is specifically suitable for Steel holder head B, allowing seamless integration into existing quick-change systems that employ this head type. The design eliminates intermediate clamping elements where possible, promoting a compact tool stack and reliable axial positioning. Clear dimensional data—40 mm bore and 120 mm length—supports accurate planning when laying out tool assemblies or verifying spindle clearance. Supply assurance and quality filter from a trusted partner Availability is backed by a structured supply chain and a dedicated distribution partner that acts as a European quality filter. Sourcing through this channel provides access to a broad portfolio of precision components and the assurance of consistent product verification. Traceability of the unit and concise technical data help procurement and production planners to align requirements without compromising on operational reliability. Contact Metav Werkzeuge for a compatibility check or to arrange immediate supply from Emmerich: call +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data Article number: 2000832172NW Label: Wechselhalter f.Stahlhalterkopf B f.gr.Zylinderschäfte Spann-D.40mm TECWERK Product type: Quick-change holder Manufacturer: TECWERK UID: 2000832172NW Facts Bore diameter: 40 mm Overall length: 120 mm Packaging unit: 1 Special features with cylindrical bore for direct reception of large boring bars and Morse taper sleeves for quick-change steel holder head B suitable for large cylindrical shanks FAQ What is the clamping or bore diameter of the holder? The holder provides a 40 mm cylindrical bore as the clamping interface for large shanks. Is the unit compatible with Morse taper sleeves? Yes, the design allows direct mounting of Morse taper sleeves for quick tool swaps. Which holder head does this unit fit? This quick-change component is intended for use with Steel holder head B and integrates into compatible quick-change systems. What is the overall length of the holder? The total length is 120 mm, providing stable engagement and axial support. Can large boring bars be mounted directly? Yes, the holder is specified for direct acceptance of large boring bars, reducing the need for additional adapters. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
120mm Toolholder For Steel Tool Holder Head B With 32mm Clamping Height - TECWERK
Benefit from the precise 32 mm clamping height and a 120 mm overall length, which together deliver dependable positioning and improved reach for turning operations; order this holder directly via Metav Werkzeuge or consult the technical team for configuration advice. Interchangeable holder for Steel Holder Head B — 32 mm clamping height (TECWERK) The Interchangeable holder for Steel Holder Head B is a compact toolholder designed for turning tools, offering a 32 mm clamping height for consistent tool geometry and reliable workshop use. 32 mm clamping height for consistent positioning 120 mm overall length for stable reach Compatible with Steel Holder Head B Designed for turning tool applications Precision and stability for turning operations The combination of a defined clamping height A: 32 mm and a 120 mm overall length ensures consistent tool geometry and reduces the need for repeated readjustment. A fixed clamping height directly influences tool centreline alignment and cutting performance; this holder keeps the tool axis predictable, which improves repeatability across serial operations and helps maintain surface quality. For shops focused on throughput, the measurable consistency of the mounting interface reduces scrap and machine downtime by simplifying set-up procedures and preserving cutting parameters between jobs. Seamless compatibility to reduce setup time Designed specifically for use with Steel Holder Head B, this interchangeable toolholder simplifies tooling logistics in mixed-machine environments. The straightforward compatibility reduces the variety of holders required on the shop floor and shortens changeover times during tool replacement or regrinding cycles. As a standardised accessory for turning applications, the component supports streamlined inventory management and faster tooling swaps, thereby increasing productive hours on the lathe and lowering indirect labour spent on set-up. Workflow advantages and practical handling in the workshop Supplied in a single unit, the holder suits repair, replacement and small-batch production contexts where predictable handling matters. The compact design supports secure clamping and contributes to vibration damping when mounted at the correct clamping height, which helps preserve insert life and improve surface finish. For technical clarification or to verify fit with a specific machine tool, Metav Werkzeuge provides product coordination and specification guidance so the correct configuration is selected for each application. Contact Metav Werkzeuge for expert advice on TECWERK interchangeable holders and to confirm the optimal 32 mm clamping-height configuration for workshop needs Technical data Article number: 2000832158NW Product name: Wechselhalter f.Stahlhalterkopf B f.Drehstähle Spann-H.32mm TECWERK Product type: Wechselhalter Manufacturer: TECWERK Packaging unit: 1 Facts Overall length: 120 mm Clamping height A: 32 mm SKU / UID: 2000832158NW Special features For turning tools Compatible with Steel Holder Head B Interchangeable holder design FAQ What applications is this holder intended for? This Interchangeable holder for Steel Holder Head B (TECWERK Wechselhalter, SKU 2000832158NW) is intended for turning tool applications and workshop lathe use. What is the clamping height of the holder and why does it matter? The holder specifies a clamping height A of 32 mm; the 32 mm clamping height in the TECWERK Wechselhalter 2000832158NW ensures consistent tool centreline alignment for repeatable cutting conditions. Which head is this holder compatible with? Compatibility is specified for Steel Holder Head B; the TECWERK interchangeable holder is designed to mount directly to a Steel Holder Head B interface. What is the overall length and how does that affect performance? The overall length is 120 mm; a 120 mm reach balances accessibility and rigidity for turning tasks with the TECWERK holder 2000832158NW. How is the product supplied? The product is supplied as a single unit (packaging unit 1) for the TECWERK Wechselhalter 2000832158NW. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
120mm Toolholder For Steel Toolholder Head B 25mm Mounting Height - TECWERK
Take advantage of the interchangeable design, precise clamping height (25 mm) and a compact overall length of 120 mm to secure consistent tool set-up and short changeover times on turning centres; order via Metav Werkzeuge or consult our specialists for application advice. TECWERK interchangeable holder for steel holder head B — clamping height 25 mm The TECWERK interchangeable holder for steel holder head B is designed for secure mounting of turning bars and fast changeovers in workshop and production environments. Interchangeable holder design Clamping height 25 mm Overall length 120 mm Compatible with steel head B Precision fit that stabilises turning performance A purpose-built interchangeable holder delivers repeatable seating and consistent tool geometry, which reduces rework and setup time. The defined clamping height ensures the cutting edge sits at the expected centreline; a stable centreline improves finish quality and tool life. This precision seating is particularly valuable where tolerances are tight and batch-to-batch uniformity is required. Faster changeovers for improved throughput The compact overall length 120 mm combines rigidity with space efficiency on the turret, supporting quicker tool indexing and less interference in multi-tool stations. The modular design enables swift replacement of worn holders without requalifying the entire tool assembly, helping to keep machine uptime high and production flow steady. Simple concept, clear technical benefits The solution mates with a steel holder head B, providing a standardised interface for many turning bar families. The declared 25 mm clamping height refers to the tool seating plane relative to the holder datum; keeping this datum consistent avoids repetitive height adjustments and streamlines tool presetting. The result is improved repeatability and fewer stoppages for manual corrections. Application and handling made straightforward Intended for use with turning bars, the holder is supplied as a single unit and is ready for installation in standard tool heads where the B-type steel head is fitted. The straightforward geometry facilitates cleaning and inspection during routine maintenance. For any queries about fitment or compatibility, Metav Werkzeuge offers technical information and assistance by email or phone. For personalised application advice or to secure a supply of the TECWERK interchangeable holder with 25 mm clamping height, contact Metav Werkzeuge for a reliable recommendation and seamless delivery from Emmerich. Technical data SKU: 2000832157NW Product type: Interchangeable holder Manufacturer: TECWERK Overall length: 120 mm Clamping height: 25 mm Core dimensions Overall length: 120 mm Clamping height (A): 25 mm Packaging unit: 1 Special features For turning bars Compatible with steel holder head B Interchangeable holder design Suitable for standard turret mounting FAQ Is this holder compatible with a steel holder head B? Yes. The TECWERK interchangeable holder is designed specifically for use with a steel holder head B and offers the matching interface for secure mounting. What does the clamping height of 25 mm mean in practice? The 25 mm value denotes the seating height (datum A) that determines the tool centreline; consistent clamping height simplifies presetting and maintains cutting geometry. How long is the holder and how does that affect stability? The holder has an overall length of 120 mm, which balances rigidity and reach to support stable turning operations while minimising interference in multi-tool setups. How is the product supplied and what is the packaging unit? The item is supplied as a single unit; packaging unit: 1, ready for immediate installation. What is the product SKU for ordering or enquiry? The SKU for ordering and reference is 2000832157NW and the product is listed under the TECWERK interchangeable holder category. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
150mm Toolholder Adapter For C Steel Toolholder Head, 32mm Shank Height - TECWERK
Benefit from robust compatibility with C-type steel holder heads and a precise 32 mm clamping height for dependable turning setups; order the quick-change holder directly via Metav Werkzeuge or consult the specialists if technical clarification is required. TECWERK quick-change toolholder for steel holder head C — 32 mm clamping height The TECWERK quick-change toolholder is a compact solution for workshop turning applications, designed to accept C-type steel holder heads and to support turning bars with a reliable clamping height of 32 mm. Quick-change toolholder for steel head C Clamping height 32 mm for standard set-up Overall length 150 mm for stable reach Robust construction for workshop turning Consistent set-ups that reduce machine downtime The quick-change design combines straightforward handling with repeatable positioning, enabling faster tool swaps and fewer re-alignments. Compatibility with the steel holder head C and a defined 32 mm clamping height simplifies fixture planning and minimises setup variation between operations. For production environments where cycle time and reproducibility matter, this holder supports a smoother workflow and fewer interruptions. Stability and reach for reliable turning performance With an overall length of 150 mm, the holder offers sufficient reach for common lathe configurations while maintaining rigidity at the cutting point. The elongated construction balances accessibility and stiffness, which helps to reduce chatter and improve surface finish in turning tasks. The combination of reach and stable clamping contributes directly to process reliability and consistent part quality. Designed for turning bars with clear mounting parameters Intended specifically for use with turning bars, the toolholder accepts the established C-type steel head interface and provides a known clamping datum at 32 mm. Explaining the clamping height: it denotes the vertical distance from the mounting datum to the cutting edge plane, a decisive dimension for turret and toolpost alignment. Specifying this parameter up front simplifies machine setup and avoids trial-and-error adjustments during production changeovers. Practical considerations and workshop integration The unit arrives as a single packing item and integrates into standard turning setups that use steel holder head C connections. Given the defined interface and measured dimensions, the holder is suited to systematic tool management and can be incorporated into visual tool lists or machine set-up sheets. For specialised applications or unusual tool geometries, technical clarification can be obtained to ensure correct fitment and optimal performance. Contact Metav Werkzeuge for tailored technical advice or to order the TECWERK quick-change toolholder with 32 mm clamping height — email info@metav-werkzeuge.com or call +49 2822 7131930 for prompt assistance Technical Data Article number: 2000832159NW Manufacturer: TECWERK Product type: Quick-change holder Facts Overall length: 150 mm Clamping height: 32 mm Packing unit: 1 Applications / Features For turning tools Compatible with steel holder head C Suitable for workshop turning operations FAQ Is this holder compatible with a C-type steel holder head? Yes. The quick-change toolholder is designed to accept a steel holder head C, providing a defined interface for straightforward mounting. What is the clamping height and why does it matter? The clamping height is 32 mm, indicating the vertical datum to the cutting edge plane; this dimension ensures correct tool alignment in the turret or toolpost. What is the overall length and how does that affect operation? The overall length is 150 mm, which gives adequate reach while maintaining rigidity to support stable turning and improved surface finish. Is the holder suitable for turning bars or indexable insert systems? The holder is intended for use with turning bars and the C-type steel head interface; specific indexable systems should be checked for compatibility against these mounting parameters. Which SKU identifies this product for ordering? This component is listed under SKU 2000832159NW and is supplied as a single packing unit for workshop use. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
150mm Toolholder For Steel Holder Head C With 40mm Clamping Height - TECWERK
Take advantage of the holder’s quick-change interface, precise 40 mm clamping height and 150 mm overall length for stable, repeatable turning operations; order the part directly via Metav Werkzeuge or request advice from our consultants. Interchangeable holder for steel holder head C — clamping height 40 mm (TECWERK) The Interchangeable holder for steel holder head C (clamping height 40 mm) is a quick-change tool holder designed for use with turning tool bits in precision turning applications, offering consistent seating and reliable alignment for production and workshop environments. Quick-change interface for tool posts Compatible with steel holder head C Clamping height 40 mm Overall length 150 mm Faster changeovers for uninterrupted production The quick-change design reduces non-productive time by enabling rapid replacement of tool carriers while maintaining positional accuracy. By combining a quick-change interface with a defined clamping height 40 mm, the holder supports predictable set-up routines and shorter cycle interruptions, which contributes directly to higher throughput and leaner workflows in jobbing and serial turning. Stable clamping for consistent surface finishes Engineered for use with turning tool bits, the holder gives a defined contact plane to the steel holder head C, improving repeatability and limiting micro-movement under load. This results in more consistent surface quality and reduced rework. The combination of precise seating and a measured 150 mm overall length helps preserve cutting geometry, so finishing passes remain uniform across batches. Seamless integration with existing posts and tool systems Compatibility with the steel holder head C minimises spare-part variety and eases integration into established quick-change tool posts. The standardised clamping height simplifies tool-setting procedures on lathes and reduces the need for individual shimming. Workshops benefit from reduced stocking complexity and quicker exchange routines, which in turn supports shorter lead times and predictable delivery performance. Built for workshop resilience and dependable results The holder is intended for everyday use in trade and industrial workshops, where robustness and reliable seating matter more than unnecessary complexity. Its straightforward function for turning tool bits focuses on delivering stable cutting conditions and reliable alignment, supporting both single-item precision work and repetitive production runs without elaborate maintenance procedures. For dependable quick-change performance from TECWERK, request this interchangeable holder via Metav Werkzeuge for tailored advice and fast supply; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 2000832160NW Product type: Interchangeable holder Manufacturer: TECWERK Dimensions / Core data Overall length: 150 mm Clamping height: 40 mm Packaging unit: 1 Compatibility / Special features Execution: for turning tool bits Suitable for: steel holder head C SKU: 2000832160NW FAQ What does the clamping height indicate for this holder? The clamping height of 40 mm indicates the defined seating level for the tool carrier and is essential for consistent tool geometry and repeatable set-up when using the interchangeable holder. Is the holder compatible with existing quick-change systems? Yes, the holder is designed for integration with the steel holder head C and standard quick-change tool posts to reduce set-up time and simplify spare-part management. Which applications is this holder intended for? This holder is intended for turning operations with turning tool bits, suitable for both workshop and small-series industrial turning tasks where rapid changeovers and repeatability are required. How does the overall length affect tool setup? The 150 mm overall length helps determine tool overhang and rigidity; it supports stable cutting conditions and predictable tool projection for consistent turning results. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
160mm Quick-Change Tool Holder With Cylindrical Bore 50mm, For Heavy Boring Bars - TECWERK
Efficient production with secure clamping and fast changeovers thanks to the 50 mm clamping diameter and 160 mm overall length; ideal for direct mounting of large boring bars and Morse taper sleeves. Order the quick-change holder directly via Metav Werkzeuge or consult the technical advisors for application-specific guidance. Quick-change holder for steel holder head C — 50 mm clamping diameter, 160 mm length (TECWERK) A Quick-change holder for steel holder head C designed for direct acceptance of large boring bars and Morse taper sleeves, providing a compact 160 mm reach with a cylindrical bore. Cylindrical bore for direct mounting Accepts large boring bars and Morse tapers Designed for quick-change steel holder head C 160 mm overall length 50 mm clamping diameter Precise clamping that stabilises heavy tooling The cylindrical bore and 50 mm clamping diameter enable secure, concentric seating of oversized boring bars, which reduces vibration and improves surface finish. Direct mounting avoids intermediate adapters and thus preserves axial alignment; this results in consistent concentricity and predictable machining results. For workshops that demand repeatable accuracy, the combination of bore size and seating geometry translates directly into fewer rejects and less rework. Faster tool changes for uninterrupted productivity The quick-change design is built to reduce non-productive time during setups. By integrating with a steel holder head C, the holder permits rapid release and replacement of tooling, shortening machine downtime between operations. This efficiency gain supports higher throughput without compromising process stability, making it suitable for job shops and production lines where cycle times and changeover speed are crucial. Compatibility with Morse taper sleeves and large boring bars Prepared for the direct reception of Morse taper sleeves, the holder accepts standard taper-mounted accessories, simplifying tool inventory and enabling flexible tooling strategies. A Morse taper sleeve is a tapered fitting that seats by wedging action to transmit torque and axial loads; using it here provides secure engagement while remaining easy to dismantle for maintenance. The 160 mm length balances working reach with rigidity, offering a practical compromise between access and stability. Workshop-grade reliability and low-maintenance integration Configured for robust day-to-day use, the holder focuses on mechanical simplicity: a cylindrical seating surface and proven clamping geometry minimise wear points and permit straightforward inspection. Regular visual checks and routine cleaning keep the clamping interface performing reliably; when maintained, the holder supports long service intervals and dependable repeatability. The practical layout eases inspection and replacement of wear components where needed. For secure, fast and precise machining applications, order the TECWERK quick-change holder via Metav Werkzeuge for reliable supply from Emmerich — contact: info@metav-werkzeuge.com, +49 2822 7131930 Technical data Article number: 2000832174NW Brand: TECWERK Product type: Quick-change holder Dimensions & core data Overall length: 160 mm Bore diameter: 50 mm Packaging unit: 1 Special features Cylindrical bore for direct mounting For direct acceptance of large boring bars and Morse taper sleeves For quick-change steel holder head C FAQ What materials and tool types are compatible with the quick-change holder? The Quick-change holder for steel holder head C (SKU 2000832174NW) is specified for direct use with large boring bars and Morse taper sleeves; compatibility depends on the tool shank and taper standards in use. How does the 50 mm clamping diameter affect machining stability? A 50 mm clamping diameter gives a larger contact area and, in the Quick-change holder for steel holder head C, supports improved rigidity and reduced vibration for heavy-duty boring and finishing tasks. Can the holder be used with Morse taper sleeves from different suppliers? Morse taper sleeves that conform to standard taper dimensions are suitable for use in this holder; the quick-change configuration accepts standard sleeves for straightforward interchange. What is the functional benefit of the 160 mm overall length? The 160 mm length provides sufficient reach for many internal and external boring operations while maintaining rigidity; it represents a compromise between accessibility and tool stiffness in workshop environments. Is the holder compatible with a standard steel holder head C quick-change system? Yes, the Quick-change holder for steel holder head C is designed specifically for integration with a steel holder head C quick-change system (TECWERK), enabling fast tool swaps and reliable seating. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
160mm Tool Holder For Steel Head C With 40mm Cylindrical Bore, Quick-Change Compatible - TECWERK
Benefit from the 40 mm clamping diameter and 160 mm overall length for dependable tool support and reduced setup time; the cylindrical bore enables direct mounting of large boring bars and Morse taper sleeves, improving concentricity and surface finish. Order the interchangeable holder directly via Metav Werkzeuge or ask our consultants if needed. TECWERK Interchangeable Holder — clamping Ø40 mm, 160 mm length The TECWERK interchangeable holder for a quick-change steel holder head C provides direct reception of large cylindrical shanks and Morse taper sleeves, optimised for turning and heavy-duty boring operations Cylindrical bore for direct mounting Accepts large boring bars and Morse taper sleeves For quick-change steel holder head C Clamping diameter 40 mm Efficient, stable clamping for productive machining The holder is designed to deliver secure clamping and repeatable concentricity, key for high-quality turning and boring. A 40 mm clamping diameter paired with a 160 mm overall length provides a substantial contact area that reduces vibration and improves surface finish when machining larger tools. The cylindrical bore means large-diameter boring bars or Morse taper adaptors can be fitted directly, eliminating intermediate adapters and shortening setup time. This reduction in interfaces often results in improved dimensional accuracy and fewer tool-change interruptions, supporting smoother production workflows. Seamless integration with quick-change tool heads Compatibility with the quick-change steel holder head C simplifies tool management on multi-tool turrets and lathe quick-change systems. The interchangeable design allows rapid swaps of cutting assemblies, which reduces machine downtime and increases uptime for serial production. The construction supports robust seating of Morse taper sleeves, ensuring axial and radial stability under load. By streamlining the tool-change process, the holder contributes to measurable efficiency gains and a lower total cost of operation for workshops and production environments. Practical handling and workshop advantages The execution with a cylindrical bore and direct-receive capability reduces the number of components needed during set-up and maintenance, making inventory and handling easier. The design emphasises straightforward installation into the steel holder head C system, allowing technicians to maintain focus on machining parameters rather than adapter compatibility. Durable mechanical interface characteristics promote consistent repeatability over multiple cycles, which is particularly valuable where tight tolerances and surface integrity are required. For bespoke machine interfaces or further technical specification clarification, technical advice is available to ensure correct integration. Contact Metav Werkzeuge today to discuss compatibility, request additional technical details for TECWERK interchangeable holders, or arrange expert advice on integrating the holder into existing quick-change systems Technical data Article number: 2000832173NW Product type: Interchangeable holder Manufacturer: TECWERK Label: Wechselhalter f.Stahlhalterkopf C f.gr.Zylinderschäfte Spann-D.40mm TECWERK Facts Overall length: 160 mm Bore diameter: 40 mm Packaging unit: 1 Special features Execution: with cylindrical bore Direct mounting of large boring bars and Morse taper sleeves For quick-change steel holder head C Suitable for steel holder head C FAQ What clamping diameter does the holder provide? The TECWERK interchangeable holder (Interchangeable holder, SKU 2000832173NW) provides a clamping diameter of 40 mm. Can large boring bars and Morse taper sleeves be used directly? Yes, the holder features a cylindrical bore for the direct reception of large boring bars and Morse taper sleeves without additional adaptors. Which quick-change system is this holder designed for? This unit is designed for use with a quick-change steel holder head C and integrates seamlessly into compatible quick-change tool systems. What is the overall length and how does it affect stability? The overall length is 160 mm; the extended contact length improves axial stability and helps reduce vibration during heavy-duty machining. Is this product suitable for serial production environments? The design of the interchangeable holder supports rapid tool changes and repeatable clamping, making it suitable for workshops and production settings that require consistent performance Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
180mm Tool Holder For Steel Holder Head D1 For Turning Bars 40mm Clamping Height - TECWERK
Taking advantage of the holder’s 40 mm clamping height and 180 mm overall length ensures stable tool positioning and reduced setup times in turning operations; for procurement or detailed fit checks, order via Metav Werkzeuge or consult the technical team for compatibility guidance. TECWERK Interchangeable Holder for steel holder head D1 — 40 mm clamping height, 180 mm overall length The TECWERK Interchangeable Holder for steel holder head D1 secures turning tools in quick‑change tool posts, providing consistent tool height and reliable repeatability for workshop and production environments. Quick-change holder for turning tools 40 mm clamping height for consistent tool position 180 mm overall length for stable overhang Compatible with steel holder head D1 Precise, repeatable clamping reduces setup time and scrap A defined 40 mm clamping height guarantees a reproducible tool centre relative to the workpiece, which simplifies alignment after tool changes and minimises rework. The holder’s geometry is designed to deliver repeatable clamping for turning operations, so cycle time is reduced through faster setups. For production runs where consistency matters, the controlled tool height translates into fewer adjustments and improved first‑pass yield, supporting lean workflows and predictable part quality. Stable overhang and robust feel for vibration control With a 180 mm overall length, the component balances accessibility to the cutting zone with sufficient rigidity to keep chatter under control. The extended length provides a beneficial reach while the construction supports axial and radial stability during cuts. By reducing vibration at the tool tip, the holder helps maintain surface finish and tool life, which in turn lowers operating costs and preserves downstream processes that rely on accurate contours. Seamless integration with D1 steel holder heads Designed explicitly for the steel holder head D1, this interchangeable unit fits established quick‑change systems without the need for additional adapters. Compatibility with the D1 standard saves time during retrofits and prevents unnecessary retooling expenses. The result is a compact clamping solution that suits both single‑machine shops and high‑mix production, allowing machines to be reconfigured swiftly while keeping datum points consistent. Practical advantages for workshops and production lines The quick‑change concept supports flexible tool management: fewer dedicated tool posts are required, and reconfiguration becomes a matter of minutes rather than hours. This holder is aimed at machinists and maintenance planners who prioritise uptime and predictable performance; its simple interface with D1 heads streamlines inventory and reduces the variety of spare parts needed on the shelf. Combined with Metav’s distribution and advice, the product is positioned to support both occasional users and continuous manufacturing environments. For technical verification or to check suitability for a specific turning setup, contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 for prompt consultation and ordering assistance. Technical data SKU: 2000832161NW Article: Interchangeable holder for steel holder head D1 Manufacturer: TECWERK Facts Overall length: 180 mm Clamping height (A): 40 mm Packaging unit: 1 UID: 2000832161NW Special features For turning tools Compatible with steel holder head D1 Quick‑change/interchangeable holder Application: lathe/turning operations FAQ What does the 40 mm clamping height mean for setup? The 40 mm clamping height defines the tool centre relative to the spindle axis; with the TECWERK interchangeable holder this height delivers reproducible positioning, reducing alignment time after tool changes. Is the holder compatible with other quick‑change systems? The unit is engineered for the steel holder head D1; compatibility with other systems depends on their interface—adaptation may be required for non‑D1 standards. How does the 180 mm overall length affect machining? A 180 mm overall length provides increased reach while maintaining sufficient rigidity to reduce vibration, improving surface finish and tool life during turning. Are material specifications available for the holder? Material information is not specified in the provided data; for detailed composition and heat‑treatment data, please request the technical datasheet from the supplier. Can this holder improve tool change times on small batches? Yes, the quick‑change design shortens tool swaps and helps maintain consistent tool height, which is especially beneficial for high‑mix or small‑batch production where frequent changes are required. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
180mm Toolholder for Steel Holder Head D1 With 50mm Mounting Height - TECWERK
Take advantage of a compact combination of precise clamping, standardised dimensions and straightforward compatibility to reduce setup time and maintain consistent turning results; order the interchangeable holder directly via Metav Werkzeuge or ask our consultants if technical advice is required. Interchangeable holder for steel holder head D1 – for turning bars, 50 mm clamping height (TECWERK) The Interchangeable holder for steel holder head D1 is a precision toolholder designed for workshop and industrial turning operations, offering a 50 mm clamping height and a standardised total length for reliable tool set-up. For steel holder head D1 Clamping height 50 mm Total length 180 mm Designed for turning bars Faster set-up through standardised clamping geometry The holder provides a consistent, repeatable clamping height of 50 mm, which simplifies tool changeover and reduces machine downtime. Because the unit matches the common D1 steel holder head interface, it eliminates ambiguity in tool selection and supports predictable machining set-ups. This direct compatibility shortens preparation time, improves process stability and helps maintain consistent cutting conditions across shifts. Predictable machining with defined overall dimensions With a total length of 180 mm and a clearly defined interface, the component supports precise positioning and reliable tool projection. The defined geometry assists in calculating cutting forces and clearances, and the standardised dimensions allow straightforward integration into existing tool systems. Clear numeric values enable planning of tool offsets and collision checks, which contributes to safer and more efficient lathe operation. Robust design for industrial turning applications Manufactured for use with turning bars, the holder focuses on mechanical stability and repeatable clamping to withstand routine workshop stresses. The solid construction reduces vibration at the cutting edge and supports consistent surface finish and tool life. For operations that demand steady performance, the component’s engineered fit and secure interface with the steel holder head ensure dependable machining results. Suitable applications and practical advantages Intended for lathe and turning-tool workflows, the holder is appropriate where a fixed clamping height and reliable mechanical interface are required. The straightforward design means fewer variables during set-up, making it suitable for series production and mixed-batch work. The practical benefit is a reduction in set-up errors and a more efficient changeover routine, which together improve overall shop-floor productivity. Contact Metav Werkzeuge for detailed advice on integrating this TECWERK interchangeable holder into existing tool systems and to arrange supply from our Emmerich warehouse via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 2000832162NW SKU: 2000832162NW Facts Total length: 180 mm Clamping height: 50 mm Packaging unit: 1 Special features Suitable for steel holder head D1 Execution: for turning bars Product type: Interchangeable holder Brand: TECWERK UID: 2000832162NW FAQ Is this holder compatible with standard D1 steel holder heads? Yes. The interchangeable holder is made to fit the D1 steel holder head interface and is specified for use with that type of holder in turning applications. What is the clamping height and why does it matter? The device features a clamping height of 50 mm, which ensures consistent tool tip height and simplifies set-up of tool offsets and cutting parameters in lathe operations. Can the holder be used for different turning bars? The holder is executed specifically for turning bars and provides a fixed mechanical interface; variation in bar geometry should be checked against the holder’s dimensions before use. Does the total length affect machine clearance? Yes. The total length of 180 mm should be considered when calculating overhang and clearance to avoid collisions and to ensure correct tool projection. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
30mm Quick-Change Tool Holder Head AA With 12.5mm Bore, 40-Position Indexing - TECWERK
Take advantage of a combination of rapid tool changes, 0.01 mm repeatability, and hardened, ground contact surfaces for reliable set-ups and reduced downtime; order the component directly via Metav Werkzeuge or consult our specialists for integration advice. TECWERK Quick-change tool holder head Gr. AA — eccentric clamping, 40 indexing positions The TECWERK quick-change tool holder head Gr. AA is a compact clamping interface for rapid exchange of cutting tools while preserving high positioning accuracy in turning and live tooling applications. *Eccentric clamping for fast exchanges *Repeatability of 0.01 mm for consistent set-ups *40 indexing positions at 9° increments *Hardened and ground gearing and contact faces Faster changeovers with industrial repeatability The design centres on eccentric clamping, enabling quick replacement of cutting inserts and holders without lengthy re‑alignment procedures. Thanks to a declared repeatability of 0.01 mm, setups remain consistent across tool swaps, which reduces scrap and shortens machine idle time. For production environments where cycle time and reliable tolerances matter, this component provides a measurable productivity gain without extra calibration effort. Precise angular positioning for indexed tooling A hardened tooth ring with 40 indexing positions allows positional adjustments in 9° steps, offering flexibility when arranging tool angles or using multiple insert types. The hardened and ground gear and support surfaces deliver repeatable seating and low backlash; this ensures that each indexed position returns to its nominal orientation and maintains cutting geometry, which is especially beneficial for multi‑operation tool turrets and modular tool systems. Compact reach and secure central bore With a 12.5 mm centre bore and a 30 mm maximum reach, the tool holder head suits compact toolholders and short overhang configurations where rigidity is critical. The centre bore facilitates secure mounting to the central body, while a simple set screw allows fine adjustment of tip height, removing guesswork during final set-up. The combination of a short projection and precise adjustment reduces deflection and improves surface finish on turned components. Robust construction to lower maintenance needs Critical contact areas are hardened and ground, improving wear resistance and ensuring a long service life under repetitive indexing and clamping cycles. The eccentric clamping mechanism is engineered for reliable retention and quick action, which lessens the likelihood of unplanned stops for rework. When paired with proper maintenance intervals, this tool holder head supports sustained machine availability and predictable process capability. Contact Metav Werkzeuge for technical clarification or to discuss system compatibility for the TECWERK quick-change tool holder head Gr. AA — our Emmerich team will advise on integration and delivery from stock Technical data Article number: 2000832150NW Product type: AA Product name: Schnellwechselstahlhalterkopf Gr.AA TECWERK Manufacturer: TECWERK Packaging unit: 1 Facts Centre bore: 12.5 mm Max reach: 30 mm Indexing positions: 40 Index angle step: 9° Repeatability: 0.01 mm Special features Eccentric clamping for rapid tool changes Hardened and ground gearing and plan contact face Tip height adjustable via set screw Designed for repeatable exchanges of cutting tools FAQ What degree of repeatability can be expected from this tool holder head? The TECWERK quick-change tool holder head Gr. AA delivers a repeatability of 0.01 mm, ensuring consistent return to the preset position after each exchange. How many angular positions does the index allow and what is the step size? The tool holder head provides 40 indexing positions, each corresponding to a 9° increment for precise angular adjustment. Which bore diameter and maximum reach are provided? The central bore measures 12.5 mm and the maximum reach from bore centre to end edge is 30 mm, facilitating compact and rigid mounting. Is the contact surface wear-resistant for high-frequency use? Yes, the contact faces and the tooth ring are hardened and ground, improving wear resistance and maintaining seating accuracy over many cycles. Can the cutting tip height be adjusted after mounting? Tip height is settable via a set screw at the toolholder, allowing fine correction without removing the assembly. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
32mm Quick-Change Holder With Prism For Round Drill Bars, 130mm Length - TECWERK
Take advantage of a precise prism clamp and a 32 mm clamping diameter for consistent tool alignment and fast, reliable tool changes; order the interchangeable holder directly or consult Metav Werkzeuge for system integration and compatibility advice. Interchangeable holder for Steel Holder Head B — prism clamp, 32 mm | TECWERK The Interchangeable holder for Steel Holder Head B is a precision clamping component designed to centre round drill shanks in quick-change steel holder heads for stable, repeatable tool holding. Prism clamp for round drill shanks 32 mm clamping diameter Compatible with Steel Holder Head B 1 Length 130 mm for stable engagement Repeatable centring and reduced runout for improved process stability A prism-based clamping interface delivers reliable alignment of round shanks: the integrated prism centres the tool shaft and, as a result, helps to reduce radial runout during operation. This mechanical centring is particularly valuable in setups where precision and repeatability directly affect cycle times and surface quality. The holder’s 32 mm clamping diameter provides a clear specification for tool selection and spare-part management, while the robust engagement profile ensures consistent contact in repetitive machining cycles. For production environments that prioritise measurable accuracy, the prism clamp is a simple mechanical solution that supports predictable performance. Efficient integration into quick-change tool systems Designed for use with a quick-change steel holder head, the component supports rapid tool swaps without compromising positional accuracy. Compatibility with Steel Holder Head B 1 simplifies inventory planning and reduces tooling complexity across toolrooms and maintenance benches. The specified length 130 mm and a working height of 32 mm combine to create a stable interface that resists lateral play when the system is mounted and torqued. In rational terms, less adjustment and fewer regrips translate into shorter set-up times and higher effective machine availability — a direct operational benefit for production-focused teams. Practical handling, maintenance and workshop fit Mounting and routine inspection are straightforward: the prism seat requires only visual verification and periodic cleaning to maintain optimal contact between shank and holder. The design minimises wearing surfaces and does not rely on complex moving parts, which keeps maintenance effort low and spare-part needs predictable. As a modular clamping solution, the interchangeable holder supports standardisation across multiple stations, aiding procurement and reducing the number of unique items stocked. For workshop managers aiming to consolidate tooling while keeping quality consistent, this clamping insert offers an effective balance between durability and serviceability. For tailored advice on integrating the TECWERK interchangeable holder into existing quick-change systems, or for supply options from Metav Werkzeuge, contact Metav Werkzeuge for precise recommendations and reliable logistics support from Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 2000832166NW Manufacturer: TECWERK Product type: Interchangeable holder Label: Wechselhalter for Steel Holder Head B for round drill shanks clamping D.32mm TECWERK Facts Clamping diameter: 32 mm Height: 32 mm Length: 130 mm Packaging unit: 1 Special features Prism for round drill shanks For quick-change steel holder head Suitable for Steel Holder Head B 1 Stable engagement for repeatable centring FAQ What clamping diameter does this holder support? The TECWERK interchangeable holder supports a 32 mm clamping diameter, specified for accurate selection of matching round shanks. Is the holder compatible with quick-change systems? Yes — the component is designed for use with quick-change steel holder heads and is expressly compatible with Steel Holder Head B 1. How does the prism improve machining accuracy? The integrated prism centres round tool shanks in the seat, reducing radial runout and improving repeatability during machining operations with the interchangeable holder. What are the key dimensions to note before installation? Key figures: length 130 mm, height 32 mm, clamping diameter 32 mm; these dimensions define mounting depth and engagement for the interchangeable holder. Which workshop applications benefit most from this holder? Toolrooms, drilling stations and production cells that require frequent tool changes and consistent alignment will find the TECWERK interchangeable holder valuable for standardisation and uptime optimisation. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
40mm Quick-Change Holder for Round Drill Rods with Prism, 160mm Length - TECWERK
Benefit from precise clamping with an integral prism and a secure 40 mm clamping diameter for reliable repeatability; compatible with quick-change steel holder heads, this holder streamlines tool changes and keeps production moving. Order the interchangeable holder directly via Metav Werkzeuge or consult Metav’s specialists for system integration. Interchangeable holder for Steel holder head C — with prism, 40 mm clamping diameter (TECWERK) The Interchangeable holder for Steel holder head C is engineered to secure round drill rods in quick-change tool systems, providing stable seating and repeatable positioning for workshop and production environments. *Prism securing round drill rods *40 mm clamping diameter *Compatible with steel holder head C *Solid construction for workshop use Precise seating that reduces runout and rework The integrated prism locates round drill rods reliably, turning a cylindrical workpiece into a positively referenced element for machining. Combined with the 40 mm clamping diameter, the arrangement reduces lateral play and helps to maintain concentricity during turning or drilling operations. As a result, setup tolerances are tightened and the need for secondary alignment checks is lowered, which supports consistent part quality and fewer rejects. Designed for fast changeovers and consistent repeatability Compatibility with the quick-change steel holder head C means the mount is optimised for rapid insertion and removal in modular toolholding systems. The geometry of the interface is matched to maintain axial and radial position after each change, which leads to improved repeatability across tool swaps. Shorter changeover times translate into higher effective machine utilisation and more predictable cycle times on batch runs. Robust build for daily workshop demands Constructed for industrial use, the holder’s dimensions—including a height of 40 mm and a working length of 160 mm—provide a stable footprint in the tool chain. The component is intended to withstand the mechanical loads typical of metalcutting operations while keeping clamping forces steady. This robustness minimises vibration transmission to the tool and workpiece, supporting longer tool life and a superior surface finish. Transparent integration and measurable production benefits The device is supplied as a single unit and is suited for direct installation into compatible quick-change systems; this simplicity makes retrofitting straightforward where the interface standard matches. By reducing setup iterations and tool misalignment, the holder contributes to improved throughput and lower rework costs. For projects requiring batch standardisation, the component can be specified as part of a modular tooling concept to ensure uniform performance across multiple machines. Contact Metav Werkzeuge to discuss integration with existing quick-change systems and to arrange supply from our Emmerich warehouse Technical data Article number: 2000832167NW Label: Wechselhalter for Steel holder head C for round drill rods, clamping D.40mm TECWERK Manufacturer: TECWERK Facts Clamping diameter: 40 mm Height: 40 mm Length: 160 mm Packaging unit: 1 Special features With prism for round drill rods For quick-change steel holder head C Designed for round drill rod clamping Suitable for workshop and production toolholding FAQ What clamping diameter does the holder provide? The holder provides a 40 mm clamping diameter as specified for secure fixation of round drill rods. Is this holder compatible with quick-change steel holder heads? Yes, the interchangeable holder is designed for use with the quick-change steel holder head C, ensuring repeatable seating within such systems. What are the main dimensions of the holder? Key dimensions include a height of 40 mm and a working length of 160 mm as listed in the product details. Which types of drill rods does the mount accept? The mount is intended for round drill rods and uses an internal prism to locate and secure cylindrical shanks. Is the material of the holder specified? Material information is not provided in the available product data for SKU 2000832167NW; material details should be requested if required for specific applications. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
48mm Quick-Change Toolholder Head With Eccentric Clamp, 20mm Bore, Hardened Gear - TECWERK
Take advantage of the combination of rapid tool changes, industrial-grade repeatability and hardened contact surfaces to keep set-up times low and process accuracy high. Order the TECWERK quick-change head directly via Metav Werkzeuge or consult Metav’s specialists for application advice and fast supply. Quick-change tool holder head Gr. A — 48 mm overhang, 20 mm bore (TECWERK) The Quick-change tool holder head Gr. A is a compact clamping solution for rapid interchange of turning tools in metalworking and precision turning applications. Eccentric clamping for secure fixation Repeatability 0.01 mm 40 indexable angles at 9° increments Hardened, ground serration and seating Reduce set-up time with precise, repeatable tool changes The head is engineered for fast tool swaps and consistent repositioning. Thanks to eccentric clamping and a specified repeatability of 0.01 mm, repositioning after tool changes is reliably precise, which reduces inspection cycles and downtime. For small-batch production and tool rooms where changeover speed and dimensional consistency matter, this head delivers measurable efficiency gains through fewer adjustments and less scrap. Flexible angular positioning for versatile machining A 40-tooth indexing system provides 40 distinct angular positions, each separated by 9°, enabling flexible orientation of the cutting edge without additional fixtures. The combination of indexed positions and compact design supports complex turning and profiling tasks while maintaining repeatable geometry. This indexed arrangement simplifies tool set-up, so multiple tool types can be arranged quickly and returned to a defined orientation. Durable contact surfaces and secure seating for process reliability Contact interfaces — the serration and the flat seating face — are hardened and ground to resist wear and maintain clamping fidelity under repeated cycles. The hardened surfaces help preserve the original fit and repeatability over prolonged use, supporting long-term process stability. Where repeatable accuracy is required across many change cycles, this durability reduces maintenance interventions and contributes to consistent part quality. Compact dimensions and straightforward height adjustment Designed with a 20 mm bore diameter for the central body and a maximum overhang of 48 mm, the head suits compact tool posts and restricted spaces without compromising reach. The tip height is set via a dedicated adjustment screw on the turning-tool holder, allowing precise alignment of the cutting point with minimal tools required. These compact mechanical features support tidy tool layouts and rapid alignment on the lathe. For tailored advice on integrating the TECWERK quick-change tool holder head into production workflows and for reliable supply from Emmerich, contact Metav Werkzeuge GmbH; their specialists will provide application support and fast delivery. Technical data Article number: 2000832151NW Manufacturer: TECWERK Product type: Quick-change tool holder head Packaging unit: 1 Core specifications Bore diameter: 20 mm Max overhang: 48 mm Repeatability: 0.01 mm Index positions: 40 Angle step: 9° Special features Eccentric clamping Adjustable tip height via set screw on toolholder Hardened and ground serration and seating 40-tooth steel holder head enabling 9° angle settings Rapid tool change capability FAQ How precise is the positioning after a tool change? The TECWERK quick-change tool holder head provides a repeatability of 0.01 mm, ensuring reliable repositioning after each swap. What bore size is required for mounting this head? A 20 mm central bore diameter is specified for the body, which matches standard compact tool posts and adaptors. How far can the tool project from the mounting centre? The maximum overhang is 48 mm, measured from the bore centre to the end edge of the interchangeable holder. How are angular adjustments made and how fine are the steps? Angular indexing is achieved via a 40-tooth system, giving 9° increments for defined orientation of the cutting tool. Are the contact surfaces durable for high-cycle use? Yes — the serration and the flat seating face are hardened and ground to resist wear and preserve clamping accuracy over repeated cycles. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
50mm Tool Holder Adapter For AA Steel Tool Head, 12mm Clamping Height - TECWERK
Take advantage of precise mounting and a compact footprint: compatibility with AA steel holder heads plus a 12 mm mounting height and 50 mm overall length ensure reliable positioning for turning tools; order directly via Metav Werkzeuge or consult the technical advisers for integration support. Quick-change tool holder for AA steel head (TECWERK) – 12 mm mounting height, 50 mm overall length A quick-change tool holder for AA steel heads designed for secure clamping of turning tools in compact tool posts Compatible with AA steel holder head 12 mm mounting height for standard set-ups 50 mm overall length for compact installation Designed for turning tools Accurate positioning reduces setup time The quick-change holder is engineered for repeatable positioning, delivering consistent tool alignment through its defined 12 mm mounting height and compatibility with AA steel heads. This precision shortens set-up and recalibration cycles, which in turn improves throughput in series production. The clear specification of the mounting datum supports predictable machining results and simplifies quality checks, making the holder suitable for workshops striving for measurable process stability. Compact design improves access in confined spaces With a 50 mm overall length, the holder offers a compact solution where toolpost space is limited. The reduced overhang enhances rigidity at the cutting point, lowering vibration and supporting improved surface finish on turned components. For operations requiring close tool-to-workpiece clearances or multiple-tool stations, the compact footprint enables denser tooling layouts without compromising secure clamping or operator clearance. Fast changeovers and dependable retention The quick-change concept minimises downtime: exchange of turning tools is straightforward while retaining the reference position for subsequent operations. The defined mounting height and precise interface to the AA-type head ensure reproducible clamping and consistent cutting geometry after each change. For workflows where short tool-change intervals matter, this holder reduces non-productive time and maintains process accuracy across shifts. Simple integration and low-maintenance use Specified as a dedicated holder for turning tools, the component is ready for direct integration into compatible tool heads and existing fixtures. The standardised mounting height A: 12 mm simplifies planning and spare-part management, while the compact dimensions ease storage and replacement logistics. Supplied as a single unit per packaging, the design favours straightforward inventory control and predictable assembly in both production and maintenance routines. Contact Metav Werkzeuge in Emmerich for application guidance and to procure the TECWERK quick-change tool holder 2000832155NW; call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: 2000832155NW Manufacturer: TECWERK Product type: Quick-change tool holder Execution: for turning tools Compatible with: AA steel holder head Mounting height A: 12 mm Overall length: 50 mm Packaging unit: 1 Facts Overall length: 50 mm Mounting height A: 12 mm Packaging unit: 1 Special features For turning tools Compatible with AA steel holder head Quick-change design FAQ How does the holder align with AA-type heads? The quick-change tool holder is machined to interface precisely with AA steel holder heads, using the defined 12 mm mounting height as the reference for repeatable alignment. Is the 12 mm mounting height suitable for standard tool posts? Yes, the 12 mm mounting height is a standard datum designed for compatibility with common AA head configurations and predictable clamping geometry. Can the holder be used in multi-tool turret arrangements? The compact 50 mm overall length and quick-change design make the holder suitable for dense turret layouts where secure, repeatable positioning is required. What makes changeovers faster with this holder? The quick-change concept and defined mounting datum reduce adjustment time after tool swaps, delivering consistent cutting positions without lengthy realignment. Which SKU identifies this product for ordering? This product is listed as TECWERK quick-change tool holder, SKU 2000832155NW, for straightforward procurement and stock management. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
71mm Quick-Change Tool Holder Head Gr. B With Eccentric Clamp, 32mm Bore, 0.01mm Repeatability - TECWERK
Take advantage of the combination of fast, repeatable tool changes and hardened, precision-ground contact surfaces for consistent turning results; the eccentric clamping and 40 angular positions ensure flexible machining while the 71 mm overhang accommodates extended setups — order directly via Metav Werkzeuge or consult our specialists for compatibility advice. Quick-change toolholder head Gr. B TECWERK — eccentric clamping, 40 index positions Quick-change toolholder head Gr. B TECWERK is designed for rapid tool changes in lathe and turning applications, offering high repeatability and robust, hardened contact surfaces Eccentric clamping for quick tool changes Repeatable positioning to 0.01 mm Hardened, ground gearing and seating 40 index positions in 9° steps 32 mm central bore and 71 mm overhang Precision and process reliability for turning operations The quick-change toolholder head delivers a measurable improvement in set-up speed and process stability thanks to its eccentric clamping system and confirmed 0.01 mm repeatability. The eccentric clamp secures cutting tools quickly while maintaining the repeatable position required for serial production, which reduces downtime between operations and minimises rework. For workshops and job shops that value consistent results, the unit’s measured indexing and firm seating reduce setup variability and support predictable cycle times. Flexible positioning for multi-angle tooling With 40 index positions at approximately 9° increments, this holder head enables a wide range of tool orientations without the need for separate fixtures, allowing machining strategies to be adapted on the fly. The ability to set different tool angles within a single holder supports complex facing, profiling and finishing tasks while keeping the toolcentre height adjustment straightforward via the integrated set screw. This flexibility translates into fewer tool changes on the machine and a leaner tool inventory. Robust construction for demanding shop use Critical contact areas are hardened and ground, providing a durable seating surface that resists wear and preserves alignment over time. The central 32 mm bore and the structural design accommodate stable mounting, while the maximum 71 mm overhang suits operations requiring extended reach. These characteristics combine to deliver a component that withstands the mechanical stresses of heavy turning and repeated index cycles, prolonging service life and reducing maintenance frequency. Practical handling and compatibility in production The head’s design focuses on fast handling: tool swaps are completed with the eccentric locking action, and the tip height of the turning tool is adjusted securely using the set screw on the tool post. Because the clamping and locating faces are precision-ground, repeatability is largely independent of operator skill, which supports consistent quality across different shifts and operators. For integration into existing setups, the component’s dimensions and index resolution make it suitable for a wide range of conventional and CNC lathes, provided the spindle and turret interfaces match the 32 mm centre bore. Contact Metav Werkzeuge for tailored advice on fitment and delivery from Emmerich — email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss specification details and stock availability Technical data Article number: 2000832152NW Manufacturer: TECWERK Type/Grade: Gr. B Product type: Quick-change toolholder head Core data Overhang (max.): 71 mm Central bore diameter: 32 mm Repeatability: 0.01 mm Index positions: 40 Index step: 9° Special features Eccentric clamping for rapid tool changes Tip height adjustable via set screw Hardened and ground gearing and seating Designed for consistent repetitive positioning FAQ What level of repeatability can be expected from this holder head? The Quick-change toolholder head Gr. B TECWERK provides repeatable positioning to 0.01 mm, ensuring reliable tool location across repeated changes. How many angular settings are available and what is the step size? The unit offers 40 index positions, each at approximately 9°, enabling a broad range of tool orientations without additional fixtures. What bore size is required for mounting this head? The component uses a 32 mm central bore, which must match the turret or adapter interface for correct mounting. Is the tip height adjustable and how is it set? Tip height is adjusted on the turning tool using the built-in set screw on the toolholder, allowing precise height correction after indexing. Are the contact surfaces durable for serial production? Yes. The gearing and planing contact surfaces are hardened and ground, providing wear resistance and stable seating for repetitive production runs. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
75mm Tool Holder For Steel Turning Inserts 20mm Clamping Height - TECWERK
Take advantage of a compact quick-change system that combines reliable compatibility with Steel holder head A, a defined 20 mm clamping height and a short overall length for space-critical lathe setups; order the holder via Metav Werkzeuge or consult the Metav team for application advice. TECW ERK Quick-change holder for steel holder head A — 20 mm clamp height The TECW ERK Quick-change holder for steel holder head A is a compact toolholder designed to accept turning bars and to provide a stable clamping interface in confined lathe environments. Quick-change system for turning bars Compatible with steel holder head A 20 mm clamp height for consistent seating Compact overall length 75 mm for tight setups Minimise set-up variance with defined clamp geometry The holder’s 20 mm clamping height creates a consistent datum for tool seating, which is essential for repeatable turning operations and reduced set-up adjustments. With a defined seating plane, the risk of axial runout is lowered and tool repeatability is improved; this supports predictable machining tolerances and fewer trial cuts. The modular clamping interface is intended to be integrated into established tool stations, where reliable positioning shortens calibration time and helps maintain process stability. Fit into restricted toolpost spaces without compromise A short overall length of 75 mm enables installation in tight toolpost arrangements and minimises interference with workpiece fixtures. The compact form factor allows closer tool-to-tailstock setups and better access for coolant or chip evacuation, which can improve surface finish and extend insert life. Where machine envelopes are constrained, such a small footprint helps maintain flexibility in tool layout and reduces the need for workarounds that can slow production. Interchangeability for faster changeovers and workflow continuity Designed for turning bars and matched to Steel holder head A, the quick-change concept supports rapid tool swaps and straightforward reconfiguration of the tool carousel. Changeover times are reduced because the holder is compatible with a standard head interface, enabling consistent clamping behaviour across similar toolholders. This interchangeability is conducive to lean workflows, as fewer bespoke fixtures are required and tool inventory can be standardised for easier storage and replacement. Practical scope and workshop integration The toolholder is intended for use in conventional lathe toolposts where a fixed clamping height and compact length deliver repeatable results. Routine maintenance is straightforward since the mechanical interface is deliberately simple and robust; components that determine clamping behaviour are easily inspected and cleaned. Specifications such as the defined clamp height and overall length make the holder suitable for applications where predictable tool setting and minimal setup time are priorities. Contact Metav Werkzeuge for tailored advice on integrating this TECWERK quick-change holder into workshop setups or request application-specific specifications via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: 2000832156NW SKU: 2000832156NW Product type: Quick-change holder Facts Overall length: 75 mm Clamp height: 20 mm Packaging unit: 1 Special features For turning bars Compatible with Steel holder head A Manufacturer: TECWERK FAQ How does the 20 mm clamp height affect repeatability? A defined 20 mm clamp height creates a consistent reference plane that improves repeatability by reducing variations in tool seating and minimizing axial runout for the TECW ERK quick-change holder. Is this holder suitable for compact lathe toolposts? Yes. The 75 mm overall length is designed for tight setups and allows installation in compact toolpost arrangements while maintaining secure clamping behaviour. Can the holder be used with other head types? The holder is specified for compatibility with Steel holder head A; use with other head types should only be considered if mechanical compatibility is confirmed. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
80mm Adapter Sleeve With 30mm Bore For Large Boring Bars, Quick-Change Steel Holder Head Compatibility - TECWERK
Benefit from reduced changeover times and a robust clamping interface: the holder’s 30 mm cylindrical bore and 80 mm length enable direct mounting of large boring bars and Morse taper sleeves for efficient shop-floor operation. Order the holder directly via Metav Werkzeuge or consult the specialists for integration advice. TECWERK quick-change holder for steel holder head A — 30 mm bore, 80 mm length A TECWERK quick-change holder designed for direct mounting of large boring bars and Morse taper sleeves, intended for use with steel holder head A in lathe and boring-bar applications Quick-change design for fast tool swaps 30 mm cylindrical bore for large boring bars Direct mount for Morse taper sleeves Compatible with steel holder head A Faster changeovers and steadier production flow The quick-change concept reduces non-productive time by allowing rapid swapping of tooling components, which improves throughput on batch and single-piece production runs. The combination of a 30 mm bore and an 80 mm length creates a compact, repeatable interface that supports stable clamping of large-diameter boring bars; this leads to fewer alignments and shorter setup cycles. Where uptime and predictable cycle times matter, the design contributes directly to smoother manufacturing processes. Secure reception for large boring bars and Morse tapers A cylindrical inner diameter accepts substantial tool shanks and facilitates direct mounting of Morse taper sleeves, eliminating intermediate adapters in many setups. The cylindrical reception helps to centre the shank and transfer clamping force evenly, which reduces vibration and deflection during cutting. For users less familiar with Morse tapers: these sleeves enable secure, taper-based seating of cutting tools and are routinely used where axial stability and concentricity are required. Straightforward compatibility with standard quick-change systems Engineered specifically for the steel holder head A, the adapter integrates into established quick-change tool-holder assemblies without the need for customised fixtures. This compatibility simplifies inventory management and reduces the number of variant parts held in the toolroom. The compact design also supports consistent repeatability when replacing inserts or switching bar tooling, improving part-to-part uniformity on precision operations. Practical workshop use and handling The holder is supplied as a single unit and is convenient to store as a standard spare in maintenance kits. Its simple geometry makes surface inspection and routine checks quick, and the lack of complex moving parts reduces service intervals. In practice, adopting standardised quick-change holders contributes to a tidier workflow and fewer tooling errors, supporting both small engineering shops and larger production departments that prioritise reliability. Contact Metav Werkzeuge for tailored integration advice and to secure the TECWERK quick-change holder for improved lathe and boring-bar operations; Metav Werkzeuge supports delivery and technical consultation from Emmerich Technical data Article number: 2000832171NW Label: Quick-change holder for steel holder head A, 30 mm bore Manufacturer: TECWERK Product type: Quick-change holder Numbers Overall length: 80 mm Bore diameter: 30 mm Length (l): 80 mm Packaging unit: 1 Special features with cylindrical bore direct reception of large boring bars for Morse taper sleeves for quick-change steel holder head suitable for steel holder head A FAQ What is the primary function of this holder? The TECWERK quick-change holder is designed to provide a stable, repeatable interface for large boring bars and Morse taper sleeves, streamlining tool changes in lathe and boring applications. Which tool-holding systems is it compatible with? Compatibility is intended for the quick-change steel holder head A and standard Morse taper sleeves; the 30 mm cylindrical bore accommodates larger shank diameters used in heavy-duty boring. What are the key dimensions to check before ordering? Verify the bore diameter (30 mm) and overall length (80 mm); these dimensions determine fit with the existing steel holder head and the required reach for the machining operation. Can Morse taper sleeves be mounted directly? Yes, the design allows direct mounting of Morse taper sleeves, enabling a secure taper-based seating without additional adapters in many cases. What is the SKU or article number for ordering? The article number is 2000832171NW; this identifies the TECWERK quick-change holder for procurement and stock control. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
85mm Tool Holder For Round Shank Drill Rods With Prism, 20mm Clamping Diameter - TECWERK
Reliable clamping is provided by the integrated prism and the defined clamping Ø 20 mm, while the quick‑change design ensures fast swaps and reproducible positioning in compact tool racks. Compact dimensions (length 85 mm, height 20 mm) permit integration into dense machining setups. Order the interchangeable holder directly via Metav Werkzeuge or consult the Metav team for application advice. Interchangeable holder for steel holder head A — prism seating, clamping Ø 20 mm (TECWERK) Interchangeable holder for steel holder head A is a quick‑change clamping component with prism seating designed for secure mounting of round drill rods in metalworking fixtures. Prism seating for round drill rods Clamping diameter 20 mm Quick‑change for steel holder head A Accurate alignment for repeatable machining results The built‑in prism offers defined seating for round drill rods, reducing radial play and supporting precision in serial operations. With a clamping Ø 20 mm, the holder provides a consistent contact geometry that helps to lower runout and improves tool life through stable support. This configuration is particularly suited to applications where reproducible tool position and minimal re‑setup time are required. Fast tool changes that reduce downtime The quick‑change interface, designed for the steel holder head A, enables rapid replacement of tooling while maintaining repeatable clamping accuracy. The compact length 85 mm contributes to short tool overhangs, which helps to preserve stiffness in the holder assembly and supports higher process reliability. The result is a measurable efficiency gain in operations where frequent tool swaps are necessary. Compact format for flexible workshop integration With an overall length of 85 mm and height of 20 mm, the holder is engineered for integration into tight tool magazines and multi‑spindle fixtures. The simple prism seating concept keeps the design straightforward and robust, allowing the component to be used as a dependable clamping element for round drill rods across a variety of machining set‑ups. The combination of small footprint and precise seating supports straightforward retrofitting into existing quick‑change systems. For reliable clamping and rapid tool swaps, request the TECWERK interchangeable holder from Metav Werkzeuge for direct supply from Emmerich or ask Metav's consultants for application guidance via info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: 2000832165NW Product type: Interchangeable holder Brand: TECWERK Suitable for: Steel holder head A Execution: with prism for round drill rods Packaging unit: 1 Dimensions & numerical data Overall length: 85 mm Length l: 85 mm Height: 20 mm Clamping diameter: 20 mm Special features Prism seating for round drill rods For quick‑change steel holder head Compatible with round drill rods FAQ What clamping diameter does the holder support? The interchangeable holder for steel holder head A provides a clamping diameter of 20 mm, suited for standard round drill rods. Is this holder compatible with quick‑change systems? Yes, the TECWERK interchangeable holder is designed for a quick‑change steel holder head and permits fast tool swaps while maintaining repeatable positioning. What are the overall dimensions of the holder? The holder has an overall length of 85 mm and a height of 20 mm, offering a compact footprint for dense tool arrangements. Which seating principle secures the round rods? A prism seating secures round drill rods, ensuring defined contact and reduced radial play for improved machining stability. Can the holder be retrofitted into existing head systems? The holder is intended for use with steel holder head A and can be integrated into compatible quick‑change setups where that interface is present. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
92/102mm Quick-Change Tool Holder Head Gr. C With Eccentric Clamp, 40° Indexing 40mm Bore - TECWERK
Take advantage of rapid tool changes with eccentric clamping and repeatability of 0.01 mm for consistent production quality; order the component directly via Metav Werkzeuge or consult our specialists for application-specific advice. Quick-change toolholder head Gr. C (TECWERK) — eccentric clamping with 40-position indexing The Quick-change toolholder head Gr. C is designed for rapid swapping of turning tools while preserving precise alignment and repeatability in metalworking setups. Eccentric clamping for fast tool swaps Repeatability of 0.01 mm for consistent parts 40-position indexing in 9° increments Hardened and ground gearing and seating surfaces Reduce setup time with precise quick changes The combination of eccentric clamping and a secure seating design enables significantly faster changeovers compared with conventional clamping methods, reducing machine downtime and increasing throughput. The mechanism maintains a repeatability of 0.01 mm, which translates into fewer adjustments after each swap and less scrap. The tip height is adjustable via a set screw, allowing correct tool alignment without shims; this feature simplifies setup routines for both single-piece flow and batch production. Greater flexibility through indexed positioning and reach control With 40-position indexing offering 9° steps, the head allows fine angular adjustment of cutting tools to suit a variety of operations and geometries. The central bore of Ø 40 mm and a maximum reach of 92 / 102 mm (centre of bore to end/edge) provide clear information for planning tool envelopes and collision checks. These measurable parameters help integrators and workshop planners to layout fixtures and determine clearance quickly, supporting efficient cell design and predictable cycle times. Robust construction for long service life and consistent accuracy The drive teeth and contact faces are hardened and ground, reducing wear and preserving the locating accuracy over extended use. The hardened planar seating and precision-cut teeth ensure that the indexed positions remain stable under cutting loads, which reduces recalibration frequency and life-cycle costs. The design therefore supports a higher degree of process reliability and contributes to dependable part conformity in demanding turning applications. For tailored advice or to obtain a quote for the TECWERK quick-change toolholder head Gr. C, contact Metav Werkzeuge — our specialists in precision solutions can assist with compatibility checks and order processing. Technical Data Article number: 2000832153NW Manufacturer: TECWERK Product type: Quick-change toolholder head Gr. C SKU: 2000832153NW Facts Bore diameter: 40 mm Max reach: 92 / 102 mm Repeatability: 0.01 mm Indexing positions: 40 (9° steps) Special features Eccentric clamping for rapid tool changes Tip height adjustable by set screw Hardened and ground gearing Hardened and ground seating/planar contact 40 teeth enabling 40 angle settings FAQ How accurate is the positioning after a tool change? The head provides a repeatability of 0.01 mm, ensuring consistent repositioning after each change. What angular resolution is available for tool orientation? Indexing is available in 40 positions with 9° increments, allowing fine adjustment of the cutting edge orientation. What is the bore diameter and how does it affect mounting? The central bore is 40 mm; it is the diameter of the main body bore used for mounting and alignment in the turret or toolpost. Can the tip height be corrected without shims? Yes — the tip height is set using a set screw on the toolholder, permitting straightforward height adjustment during setup. What ensures long-term durability of the indexing mechanism? The teeth and seating faces are hardened and ground, which minimises wear and keeps indexed positions stable under load. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com