100mm T-Slot Bolt 14mm T-Slot M12 Thread Grade 10.9 With Nut And Washer - AMF
Take advantage of the combination of M12 thread, 100 mm overall length and Grade 10.9 strength for reliable fixture clamping; this solution fits standard 14 mm T-slots and comes with a nut and washer from AMF. Order the AMF T-slot bolt directly via Metav Werkzeuge or ask our consultants if needed. AMF T-slot bolt DIN 787, M12 × 100 mm, Grade 10.9 — T-slot bolt for 14 mm T-slots The AMF T-slot bolt secures workpieces and clamping elements in 14 mm T-slots on machine tables and fixtures for industrial workholding. High-strength Grade 10.9 steel Thread size M12 for robust clamping Fits 14 mm T-slot profiles Includes nut and washer AMF Secure clamping designed for machine tables The bolt is produced to DIN 787, the recognised standard for T-slot fasteners, ensuring consistent geometry for safe seating in a 14 mm T-slot. As a dedicated T-slot bolt, it converts axial tightening into secure lateral clamping, reducing torsion and movement of fixturing components. This characteristic provides a measurable improvement in setup repeatability and reduces time spent on re-adjustment during batch production runs, supporting a smoother workflow on milling tables and drill presses. High tensile strength for demanding applications Manufactured in Grade 10.9, the fastener offers elevated tensile and yield strength compared with lower grades, making it suitable for heavier clamping and frequent tightening cycles. The M12 thread provides a balance between load-bearing capacity and compatibility with standard clamping hardware, enabling firm torque transfer without excessive thread wear. For operations where reliability under repeated stress is required, the higher strength grade translates into longer service life and reduced likelihood of fastener failure. Practical dimensions and included hardware for immediate use With an overall length of 100 mm, the bolt covers a wide range of fixture thicknesses while maintaining adequate thread engagement for safe clamping. The delivery includes a nut and washer from AMF, packaged as a complete fastening set ready for installation. Additional dimensional references are provided as additive values: A: 13.7 mm; B: 65 mm; E: 22 mm; K: 8 mm — these figures assist engineers during fixture design and when verifying clearances on bespoke setups. Versatile in workshop applications and reliable supply This fastening solution is well suited to jigs, fixtures, modular fixturing systems and general machine table accessories where a standard 14 mm T-slot is present. The standardised form factor simplifies inventory management and replacement planning. Combined with Metav’s logistics and quality assurance, the risk of delayed replacement or inconsistent parts is reduced, supporting uninterrupted production and dependable workshop performance. For secure, standard-compliant clamping with AMF Grade 10.9 reliability, contact Metav Werkzeuge for tailored advice and rapid supply direct from Emmerich. Technical data SKU: 4000833319NW UID: 4000833319NW Product type: T-slot bolt Standard: DIN 787 Manufacturer: AMF Packaging unit: 1 Includes: nut and washer AMF Facts Thread: M12 Overall length: 100 mm T-slot width compatibility: 14 mm Packaging unit: 1 Special features Grade 10.9 high-strength fastener Additions: A 13.7; B 65; E 22; K 8 Delivered with nut and washer (AMF) Conforms to DIN 787 FAQ Which T-slot size does this bolt fit? The bolt is designed for a 14 mm T-slot and seats to the DIN 787 profile dimensions for a secure fit. Is the fastener suitable for heavy-duty clamping? Yes. The combination of Grade 10.9 and an M12 thread makes the AMF T-slot bolt appropriate for demanding clamping tasks. What is included in the delivery? Delivery comprises the T-slot bolt together with a nut and washer from AMF, provided as a ready-to-use set. How long is the bolt and what clearance does it provide? Overall length is 100 mm; additional dimensional additions are A: 13.7 mm, B: 65 mm, E: 22 mm and K: 8 mm to support clearance and design checks. Which standard does the fastener comply with? The component is manufactured to DIN 787, ensuring standardised geometry for machine-table applications. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
100mm T-Slot Bolt DIN 787 18mm T-Slot M16 Length 100mm Grade 8.8 - AMF
Robust clamping and dependable tensile strength from the M16 thread and property class 8.8 enable secure fixing in 18 mm T‑slots; the 100 mm overall length provides deep engagement for stable assemblies. Order the component directly via Metav Werkzeuge or consult our specialists for tailored fixture advice. T-slot bolt DIN 787 — T-slot 18 mm, M16, 100 mm — AMF A T-slot bolt DIN 787 T-slot 18 mm M16 L100 mm property class 8.8 AMF engineered for secure workholding in machine tables, modular fixturing and industrial clamping systems. DIN 787 standard for reliable fit 18 mm T-slot compatibility M16 metric thread, high clamping force 100 mm overall length for deep engagement Property class 8.8 steel for strength Secure fastening for industrial fixturing The DIN 787 compliance ensures the bolt engages predictably with compatible T‑slots, reducing play and alignment errors during assembly. With an M16 thread, the fastener delivers considerable clamping capacity while remaining compatible with standard metric nuts and clamping elements. This combination of standard conformity and thread size translates into a measurable improvement in fixture stability, particularly where repeatable positioning and vibration resistance are required. For production environments, the result is fewer re‑set operations and a more reliable machining process. Practical dimensions for predictable assembly Precise dimensions matter when assembling clamping systems; the 100 mm overall length allows deeper engagement into fixtures and supports thicker workpieces or multi‑plate arrangements. The supplied dimensional data — A: 17.7 mm; B: 65 mm; E: 28 mm; K: 10 mm — give clear reference points for planning clearances and reach. These values support both quick compatibility checks and CAD validation, making it straightforward to confirm that the fastener meets the spatial requirements of a given setup before procurement or installation. Strength and application suitability Rated property class 8.8, this fastener offers a robust balance between tensile strength and ductility suitable for many workshop and light industrial applications. The specification favours secure clamping in general machining, assembly jigs and fixture plates without over‑engineering the solution. Where higher hardness or specialist coatings are required, consider specifying those requirements separately; for standard mechanical clamping tasks, the combination of property class 8.8 and metric threading provides a dependable foundation for everyday use. Integration into existing systems and procurement ease As a standard T‑slot component, the bolt integrates seamlessly into modular clamping systems and machine tables with an 18 mm T‑slot. Its compatibility with commonly available clamping elements simplifies sourcing and reduces the number of bespoke parts in a workshop. For purchasers seeking consolidated supply, Metav’s offering channels high availability and transparent logistics from Emmerich, helping to keep assembly lines moving without prolonged waiting times. Technical drawings and fitting advice are available on request to support correct selection for specific fixtures. For reliable clamping solutions from AMF, contact Metav Werkzeuge in Emmerich for personalised technical advice and fast delivery to your workshop at info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: 4000603229NW Product: T-slot bolt DIN 787 Manufacturer: AMF Product type: T-slot bolt Facts T-slot size: 18 mm Thread: M16 Overall length: 100 mm Addition dimensions: A: 17.7; B: 65; E: 28; K: 10 Standard: DIN 787 Packaging unit: 1 Special features Property class: 8.8 Suitable for machine tables and modular fixturing Ideal for repeatable clamping applications FAQ Which T-slot width is this bolt compatible with? The bolt is designed for an 18 mm T‑slot and is suitable for standard machine tables and clamping rails specified to that slot width; refer to SKU 4000603229NW for exact fit. Does the fastener meet recognised standards? Yes, the component conforms to DIN 787, ensuring consistent dimensions and engagement behaviour for compatible T‑slot systems. Is this bolt suitable for heavy‑duty clamping? With property class 8.8, the bolt provides robust tensile strength for many heavy‑duty and repetitive clamping tasks; actual suitability depends on specific load and safety factors in the assembly. Are additional components required for assembly? Depending on the clamping concept, the T‑slot bolt can be used with standard nuts and washers or with dedicated clamping elements; the M16 thread allows use of common metric accessories. How to choose the correct length for a fixture? Consider total stack height and required thread engagement; the 100 mm overall length of this fastener is suited to thicker workpiece stacks and deeper fixture plates—check the A/B/E/K dimensions when planning mounting clearances. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
125mm 14mm T-Slot Screw M12 Grade 10.9 With Nut And Washer DIN 787 - AMF
Robust Grade 10.9 construction combined with an M12 metric thread and a 125 mm overall length ensures secure clamping in industrial machine tables; the bolt is supplied complete with nut and washer. Order this T‑slot fastening directly via Metav Werkzeuge or consult our advisers for application support. T-slot bolt DIN 787 – AMF | M12 thread, 14 mm T-slot, 125 mm overall length A T-slot bolt DIN 787 engineered for dependable fixture of workpieces and tooling in 14 mm T‑slot systems on machine tables and modular clamping equipment. High-strength grade 10.9 For 14 mm T-slot systems M12 metric thread Includes nut and washer Reliable clamping for demanding industrial applications This fastening solution delivers high tensile strength through its Grade 10.9 specification, making it suitable for repeated load cycles in production environments. Compliance with DIN 787 denotes its design for T‑slot use on machine tables and modular rigs; the profile engages the slot securely and resists rotation under tightening. The material and heat-treatment implied by the grade provide greater resistance to shear and tensile stress than standard bolts, which reduces the need for frequent replacements and supports continuous operation in workshops and production lines. Straightforward compatibility and quick installation Fitting is straightforward: the bolt is dimensioned for a 14 mm T‑slot, features an M12 thread and an overall length of 125 mm, and is supplied complete with a nut and washer for an immediate installation. The M12 metric thread enables the use of common torque settings and standard tooling, simplifying assembly and maintenance tasks. For technical enquiries about fitment, torque recommendations or slot geometry, Metav Werkzeuge offers direct support via email or telephone to assist with correct selection and safe use. Engineered quality and dependable supply chain Manufactured to the DIN standard under the AMF label, this T‑slot fastener reflects industrial production tolerances and traceability appropriate for professional workshops and OEM assembly. Packaged per unit for controlled release into assembly processes, the component supports a lean inventory strategy where reliability and predictable performance matter. Choosing components with clear standards and vendor backing helps maintain uptime and reduces the administrative overhead associated with non-conforming parts. Choose the AMF T‑slot bolt for secure, repeatable clamping and contact Metav Werkzeuge for precise product matching or purchasing from the Emmerich warehouse at Metav Werkzeuge; our consultants will advise on integration and supply logistics. Technical Data SKU: 4000833320NW Standard: DIN 787 Product: T-slot bolt Brand: AMF Label: T-slot bolt M12, 14 mm T-slot, L 125 mm, Grade 10.9, incl. nut and washer Key measurements T-slot width: 14 mm Thread: M12 Overall length: 125 mm Axite enrichment: A: 13.7; B: 75; E: 22; K: 8 Pack unit: 1 UID: 4000833320NW Special features Compliance with DIN 787 High-strength Grade 10.9 Includes nut and washer Designed for machine table T‑slot systems FAQ What T-slot width does this bolt require? The fastening is designed for a 14 mm T‑slot and engages securely when used in appropriately sized machine table slots. Which thread size is used on this T‑slot bolt? The product features an M12 metric thread suitable for standard tooling and torque settings. Does the delivery include fastening hardware? Yes, the T‑slot bolt is supplied with the matching nut and washer to allow immediate assembly. Is this component compliant with any standard? This AMF T‑slot bolt is specified to DIN 787, indicating its intended form and fit for T‑slot applications. Manufacturer: AMF; Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
125mm T-Slot Screw M20 Grade 8.8 DIN 787, T-Nut 20mm – AMF
Take advantage of the proven combination of DIN 787 conformity, Grade 8.8 strength and precise M20 threading for reliable clamping in 20 mm T-slots; order the fastening element directly via Metav Werkzeuge or consult the Metav specialists for selection support. AMF T-slot screw (DIN 787) – 20 mm T-nut, M20, 125 mm, Grade 8.8 A AMF T-slot screw (DIN 787) designed for secure clamping in machine table T-slots and fixture systems, offering standardised dimensions and robust tensile properties. DIN 787 standardised T-slot screw Fits 20 mm T-slots M20 thread, 125 mm overall length Grade 8.8 high tensile strength Consistent clamping performance for production environments Manufactured to DIN 787, this T-slot fastening delivers a precise fit in machine table grooves and fixture plates. The combination of M20 thread and 125 mm overall length ensures reliable engagement and consistent clamp pressure for medium to heavy-duty applications. The Grade 8.8 designation indicates a high-tensile fastener that maintains preload under dynamic loads; this regularity reduces retightening intervals and supports predictable process performance. Clear specification for correct selection and assembly The defined geometry — matched to a 20 mm T-slot — simplifies component selection and reduces setup time. The coarse thread size (M20) enables secure torque transmission while the overall length provides necessary engagement depth for many jigs and workholding arrangements. For customers less familiar with standards, DIN 787 denotes standardised T-slot dimensions, meaning compatible counterparts from other manufacturers will align without modification, aiding interchangeability on workshop equipment. Practical advantages on the shop floor and in maintenance Using a standardised, high-strength fastener reduces downtime caused by incorrect or underspecified hardware. The fastener’s geometry supports straightforward installation with common torque tools; retention in the T-slot is immediate once positioned and tightened. For complex assemblies or unusual configurations, Metav’s product data and advisors can clarify whether the AMF T-slot screw matches exact fixture requirements and recommend complementary components to complete the clamping system. For secure and standard-compliant clamping elements, order the AMF T-slot screw via Metav Werkzeuge or contact Metav’s consultants at info@metav-werkzeuge.com / +49 2822 7131930 for tailored advice and supply options Technical data Article number: 4000603236NW Product: T-slot screw (T-Nutenschraube) Manufacturer: AMF Standard: DIN 787 Facts Thread: M20 T-slot width: 20 mm Overall length: 125 mm Pack quantity: 1 Addition: A: 19.7; B: 85; E: 32; K: 12 Special features Grade 8.8 tensile class Standardised T-slot geometry Designed for machine table and fixture clamping Axite enrichment dimensional values included FAQ What T-slot size does this screw fit? This screw is specified for a 20 mm T-slot, ensuring compatibility with standard 20 mm machine table grooves. What does Grade 8.8 mean for load capability? Grade 8.8 indicates a high-tensile steel fastener; the AMF T-slot screw therefore provides elevated strength and maintains preload under typical workshop loads. Is the fastener compliant with an industrial standard? Yes, the T-slot screw is manufactured to DIN 787, which standardises T-slot fastening geometry for interchangeability. Which thread and length are provided? The product features an M20 thread and an overall length of 125 mm, suitable for medium to heavy clamping engagements. Can the dimensional additions A, B, E and K be used for fixture planning? Yes, the listed additions (A: 19.7; B: 85; E: 32; K: 12) supply the key dimensions needed for precise fixture and component layout. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
14mm T-Slot Bolt M12 L63mm Grade 10.9 With Nut And Washer, DIN 787 - AMF
Take advantage of the combination of DIN 787 conformity, Grade 10.9 strength and a precise M12 thread for reliable clamping in standard machine tables; order the part directly via Metav Werkzeuge or consult our advisors for application guidance. AMF T-slot bolt DIN 787 – M12 thread, 14 mm T-slot, 63 mm length The AMF T-slot bolt DIN 787 is a heavy-duty T-slot fastener designed for secure clamping on 14 mm T-slot machine tables, supplied complete with nut and washer for immediate installation DIN 787 standard compliance Fits 14 mm T-slots M12 thread with 63 mm length Grade 10.9 strength with nut and washer Dependable clamping for machining and fixturing The fastener is specified to DIN 787, which ensures consistent geometry and interchangeability across T-slot systems; this standardisation makes the component a dependable choice for production environments requiring reproducible clamping forces. With a Grade 10.9 rating, the bolt offers high tensile strength and resistance to shear loads, helping to maintain fixture integrity during intermittent and continuous machining cycles. The mechanical properties translate directly into reduced rework and fewer stoppages, supporting a more efficient workflow. Precision fit for standard T-slot tables Designed for a 14 mm T-slot, the shank geometry ensures positive seating and accurate alignment in common machine tables and modular fixtures. The M12 thread provides a familiar interface for clamping tooling, while the 63 mm overall length allows for sufficient engagement when used with workpieces, clamps and support blocks. Supplied complete with nut and washer, the fastener is ready for assembly, eliminating the need to source separate fastening hardware and simplifying inventory management. Practical assembly details and dimensional data Key dimensional additions are provided for integration: A: 13.7 mm, B: 45 mm, E: 22 mm, K: 8 mm, assisting in planning clearances and seating depths when designing or setting-up fixtures. The component is presented as a compact, purpose-built T-slot fastener that supports robust clamping without excess bulk, enabling close placement of clamps and efficient use of table space. Traceability is supported by the catalogue reference SKU 4000833317NW, which simplifies procurement and stock control. Contact Metav Werkzeuge for technical advice and to secure AMF T-slot bolts directly from Emmerich – email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 4000833317NW SKU: 4000833317NW Norm: DIN 787 Product type: T-slot bolt Brand: AMF Packaging unit: 1 Facts T-slot width: 14 mm Thread: M12 Overall length: 63 mm Strength class: Grade 10.9 Axial additions: A: 13.7; B: 45; E: 22; K: 8 Special features Supplied with nut and washer Conforms to DIN 787 Designed for machine table clamping Heavy-duty fastening for fixtures FAQ What slot size is this fastener intended for? The fastener is made for a 14 mm T-slot and will seat correctly in standard 14 mm machine table grooves. Which thread size does the bolt use? This T-slot bolt features an M12 thread, matching common clamping hardware and accessories for secure assembly. Is the bolt delivered ready for installation? Yes, the item is supplied complete with nut and washer, enabling immediate use upon installation. What strength class does the fastener have? The component is classified as Grade 10.9, providing high tensile strength suitable for demanding clamping tasks. How can the part be identified for ordering or restocking? Reference SKU 4000833317NW when ordering or checking inventory to ensure the correct AMF T-slot bolt is supplied. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
160mm 20mm T-Slot Bolt M20 Grade 8.8 DIN 787 - AMF
Take advantage of a DIN‑compliant fastening solution that pairs standardised compatibility with high tensile strength and precise dimensions for reliable clamping performance; order the AMF T‑slot bolt via Metav Werkzeuge for dependable supply and expert advice. AMF T‑slot bolt (DIN 787) — T‑slot 20 mm, M20, 160 mm The AMF T‑slot bolt designed for secure clamping in machine tables and fixtures, compatible with 20 mm T‑slots and specified to DIN 787 for industrial use *Conforms to DIN 787 *High tensile grade 8.8 *Designed for 20 mm T‑slots *M20 thread, 160 mm length Secure, standardised clamping for machine tooling A robust fastening element built to DIN 787 ensures consistent fit in machine table grooves and dedicated clamping systems. The M20 thread and compatibility with a 20 mm T‑slot deliver a predictable mechanical interface that simplifies tool selection and reduces the risk of mismatch. Specified as a T‑slot bolt, the component provides a compact clamping solution that integrates with standard fixtures and workholding accessories, promoting production continuity and minimising setup time. Strength classification that supports industrial demands Specified in Grade 8.8, this fastener offers a well‑recognised balance of tensile strength and ductility appropriate for many workshop and light industrial clamping applications. The classification indicates a hardened and tempered metric bolt standard, enabling secure clamping under dynamic loads while maintaining reliable thread engagement. Choosing a fastener with a confirmed strength class reduces uncertainty in load calculations and supports safer, more predictable fixation in jigs and fixtures. Precision dimensions for fast assembly and repeatable results Exact dimensions reduce guesswork during assembly: the 160 mm overall length and the complementary dimensional set (A: 19.7 mm; B: 110 mm; E: 32 mm; K: 12 mm) allow planners to verify clearance and reach before installation. The provided dimensional data, recorded as Axite additions, helps machine operators confirm that the bolt achieves the required clamping stroke without interference. Where space and alignment are constrained, these measured values support faster decision‑making and fewer trial adjustments. Reliable supply and practical application in workshops As a branded component from AMF, this T‑slot bolt suits maintenance, retrofit and new‑build scenarios in metalworking and assembly environments. Supplied in single units, the bolt is suitable for targeted replacements or custom setups where individual items are required. Combined with Metav Werkzeuge’s role as a precision distributor, procurement is straightforward and supported by a stocked warehouse in Emmerich that acts as a quality filter for the European market, ensuring prompt availability and traceable sourcing for professional buyers. For a reliable, DIN‑compliant fastening solution from AMF and fast supply from Metav Werkzeuge, request the exact dimensions or place an enquiry with Metav Werkzeuge for tailored delivery from Emmerich. Technical data Article number / SKU: 4000603237NW Product designation: T‑slot bolt (DIN 787) Brand: AMF Standard: DIN 787 Data Thread: M20 T‑slot width: 20 mm Overall length: 160 mm Strength class: 8.8 Axite additions: A 19.7 mm, B 110 mm, E 32 mm, K 12 mm Packaging unit: 1 Special features Conforms to DIN 787 Designed for machine table T‑slots Single‑piece fastener for clamping applications Suitable for workshop and industrial fixturing FAQ What standard does this T‑slot bolt comply with? The bolt is manufactured to DIN 787, ensuring compatibility with standard T‑slot profiles and predictable mechanical interfaces. Which T‑slot width is this bolt intended for? This T‑slot bolt is intended for a 20 mm T‑slot, matching common machine table grooves used in industrial fixtures. What does Grade 8.8 indicate for this fastener? Grade 8.8 denotes the bolt’s strength classification, indicating a hardened and tempered metric fastener suitable for demanding clamping tasks where reliable tensile performance is required. Can the bolt reach deep clamping positions? With an overall length of 160 mm and the given Axite dimensions (A: 19.7 mm; B: 110 mm; E: 32 mm; K: 12 mm), the bolt is specified to provide sufficient reach for many clamping setups; verify the listed dimensions against the fixture before assembly. How is the item supplied and when is it suitable to order a single piece? The product is supplied in a packaging unit of 1, making it appropriate for individual replacements or one‑off applications in maintenance or prototype work. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
160mm T-Slot Bolt 18mm T-Slot M16 Grade 8.8 DIN 787 - AMF
Take advantage of a standardised fastening solution that combines conformity to DIN 787, a robust M16 thread and a 160 mm shank for reliable clamping in 18 mm T-slots — order directly via Metav Werkzeuge or consult our specialists for application advice. T-slot bolt DIN 787 — 18 mm T-slot, M16, L 160 mm (AMF) A T-slot bolt DIN 787 engineered for secure fixturing and tooling clamping in industrial 18 mm T-slots. DIN 787 standardised T-slot bolt Fits 18 mm T-slots M16 coarse thread for strong clamping Grade 8.8 high-strength specification Consistent, standardised clamping that speeds setup The bolt is manufactured to DIN 787, ensuring a predictable fit across common machine tables and clamping systems. This standard conformity reduces setup time and minimises alignment checks, delivering a measurable improvement in process repeatability. With its 18 mm T-slot compatibility and M16 thread, the component is immediately recognisable as a workshop-grade fastening element that integrates with existing fixtures and clamping kits — a practical choice for production and maintenance teams seeking fewer sourcing variables and faster changeovers. High-strength design for secure, repeatable force Specified as Grade 8.8, the fastener offers high tensile capacity compared with general-purpose screws, which translates into secure clamping under dynamic loads and machining forces. The M16 thread provides coarse engagement for robust torque transmission and reduced risk of thread stripping during repeated use. For assembly work where clamp force and repeatability matter, this fastener delivers a durable connection that supports daily workshop demands without compromising fixture integrity. Practical geometry for workshop compatibility and handling A total length of 160 mm and the detailed axial dimensions support deep engagement and clearance planning for bespoke fixturing setups. The delivered geometry data (A: 17.7 mm, B: 100 mm, E: 28 mm, K: 10 mm) allows straightforward integration into CAD layouts and fixture sheets, aiding purchasing decisions and engineering checks. Supplied under the AMF designation, the bolt suits milling tables, clamping rails and modular workholding systems where a standard, strong, and easy-to-specify fastening solution is required. Secure reliable clamping with AMF T-slot bolts — contact Metav Werkzeuge for tailored application advice and availability via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 4000603231NW Label: T-Nutenschraube DIN 787 T-Nut 18mm M16 L.160mm Güte 8.8 AMF Standard: DIN 787 Manufacturer: AMF Packaging unit: 1 Core dimensions T-slot width: 18 mm Thread: M16 Total length: 160 mm A: 17.7 mm B: 100 mm E: 28 mm K: 10 mm Special features Grade 8.8 strength class Designed for workshop and industrial fixturing Suitable for milling tables and clamping rails Axial geometry provided for integration FAQ What standard does this T-slot bolt conform to? The bolt is manufactured to DIN 787, ensuring compatibility with standard 18 mm T-slot workholding systems. Which T-slot width is this bolt designed for? This fastener is specified for 18 mm T-slots and is supplied with a M16 thread and a 160 mm shank. Is this product suitable for industrial machining fixtures? Yes — the Grade 8.8 specification and M16 coarse thread make the bolt suitable for industrial fixturing and machining applications. What is the SKU or article number for ordering? Order using article number 4000603231NW (labelled as the AMF T-slot bolt, DIN 787). Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
160mm T-Slot Bolt 18mm T-Slot M16 With Nut And Washer, Grade 8.8 - AMF
Robust DIN 787 T-slot bolt with M16 thread and 160 mm overall length for secure clamping; supplied in grade 8.8 with nut and washer for immediate installation. Order or request technical advice via Metav Werkzeuge for prompt delivery and expert support. T-slot bolt DIN 787 (18 mm T-slot, M16, 160 mm) — AMF A T-slot bolt DIN 787 engineered for reliable clamping in 18 mm T-slots on machine tables and fixturing systems. DIN 787 standard compliance Fits 18 mm T-slots M16 metric thread Grade 8.8 with nut and washer Secure clamping with standardised dimensions The fastener follows the DIN 787 specification, ensuring consistent geometry and interchangeability across standard machine tables. The combination of M16 thread and 18 mm T-slot compatibility offers a proven interface for clamping elements and fixtures, while the 160 mm overall length provides additional reach for deeper setups. The adherence to a recognised norm reduces setup errors and simplifies procurement for production environments. Quick assembly and dependable seating Supplied complete with nut and washer, the bolt is ready for immediate use in typical workshop and machining applications. The provided Axite enrichment dimensions (A: 17.7; B: 100; E: 28; K: 10) describe the head and shoulder geometry that ensures correct seating in the slot and even load distribution. This reduces the need for repeated adjustments and shortens fixture changeover times, contributing to a more efficient machining workflow. Built for workshop rigour and longevity Manufactured to grade 8.8, the component delivers high tensile strength suitable for demanding clamping tasks in industrial applications. The material specification and heat treatment implicit in this grade balance toughness and fatigue resistance, extending service life under cyclic loads. The result is a cost-effective, low-maintenance solution that supports consistent part quality over prolonged production runs. For technical consultation or to arrange supply of the AMF T-slot bolt, contact Metav Werkzeuge GmbH in Emmerich — phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data Article number: 4000833340NW Standard: DIN 787 Label: T-slot bolt DIN 787 T-slot 18 mm M16 L 160 mm Güte 8.8 with nut and washer SKU: 4000833340NW Facts Thread: M16 T-slot width compatibility: 18 mm Overall length: 160 mm Packaging unit: 1 Special features Material grade: 8.8 Supplied with: nut and washer Axite enrichment: A: 17.7; B: 100; E: 28; K: 10 Manufacturer: AMF FAQ What standard does this T-slot bolt conform to? The bolt conforms to DIN 787; the AMF T-slot bolt (SKU 4000833340NW) is manufactured to the geometry and tolerances specified in that standard. Is the thread compatible with common clamping hardware? Yes, the M16 metric thread matches widely used clamping nuts and fixtures compatible with M16 threading. Can this fastener be used immediately on delivery? The fastener is supplied with a nut and washer, enabling immediate installation in an 18 mm T-slot without the need for additional fasteners. What does grade 8.8 indicate for this bolt? Grade 8.8 denotes a medium-high tensile strength and heat-treated condition, suitable for general industrial clamping and repetitive use. Are the head dimensions documented for fixture design? The head and seating geometry is given by the Axite enrichment values (A: 17.7; B: 100; E: 28; K: 10), which support correct seating and load distribution in the slot. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
160mm T-Slot Bolt M12 Grade 10.9 DIN 787 - AMF
Take advantage of secure, high‑clamping performance combined with standardised dimensions for quick integration into existing fixturing. The M12 thread and 160 mm overall length deliver predictable engagement in 14 mm T‑slots; order directly via Metav Werkzeuge or consult Metav's technical team for compatibility guidance. AMF T-Nutenschraube DIN 787 T-Nut 14mm M12 L.160mm Güte 10.9 AMF — T-slot bolt for industrial clamping AMF T-Nutenschraube DIN 787 T-Nut 14mm M12 L.160mm Güte 10.9 AMF is a robust T‑slot bolt designed for secure workpiece clamping in machining and assembly fixtures, compatible with standard 14 mm T‑slots and engineered to DIN 787. Compliant with DIN 787 standard Designed for 14 mm T‑slots M12 thread with 160 mm overall length High‑strength Grade 10.9 steel Consistent clamping force for repeatable production The AMF T‑slot bolt conforms to DIN 787, ensuring dimensional compatibility and repeatable installation across standard machine tables and fixtures. Manufactured to Grade 10.9, the fastener offers high‑tensile properties that translate into dependable clamping force under cyclic loads. This reliability reduces setup variation and contributes to consistent part quality in serial production. The combination of a defined thread (M12) and a precise shank profile delivers controlled engagement and straightforward torque‑to‑preload behaviour, important for process stability. Practical dimensions that simplify fixture planning With a seating designed for 14 mm T‑slots and an overall length of 160 mm, the bolt provides ample reach for typical clamping arrangements while remaining compact enough for crowded setups. The specified geometry supports secure seating in the slot head and allows predictable clearance beneath the clamped assembly. These measurable characteristics simplify fixture design calculations and shorten planning time, enabling quicker changeovers. Where projection or washer stacks are required, the consistent nominal length assists in calculating required overloads and recommended torque. Durable choice backed by supply reliability Chosen for applications where downtime must be minimised, the fastener's strength class and standardised form factor make it a durable option for workshops and industrial users. Long service life is achieved by the combination of proven mechanical properties and standard compliance; this reduces the frequency of replacements and contributes to cost‑efficient maintenance cycles. For sourcing and technical clarifications, Metav's industry experience and distribution from Emmerich ensure steady supply and expertise, supporting straightforward procurement for trade and production environments. The product label and SKU facilitate traceability and stock management within existing ordering systems. For secure clamping in industrial fixtures, specify the AMF T‑slot bolt and contact Metav Werkzeuge for prompt supply and expert advice on integration into existing clamping systems. Technical Data Article number: 4000603212NW SKU/UID: 4000603212NW Standard: DIN 787 Facts T‑slot size: 14 mm Thread: M12 Overall length: 160 mm Axial dimensions: A: 13.7; B: 100; E: 22; K: 8 Special features Product type: T‑slot bolt (T‑Nutenschraube) Strength class: Grade 10.9 (Güte 10.9) Manufacturer: AMF FAQ What standard does this T‑slot bolt follow? This T‑slot bolt follows DIN 787, ensuring compatibility with standard 14 mm T‑slots and predictable installation dimensions. Which thread and length are specified for this fastener? The fastener has an M12 thread and an overall length of 160 mm, suitable for common clamping arrangements. Is this bolt suitable for heavy‑duty clamping applications? Yes — the product is manufactured in Grade 10.9, providing high‑tensile performance appropriate for demanding clamping loads. Can this bolt be used with standard 14 mm T‑slot tables without modification? The geometry and dimensions are specified for 14 mm T‑slots and are intended for direct use on compatible tables and fixtures. What information helps with ordering and traceability? Use the SKU 4000603212NW and the product designation on the label to ensure accurate ordering and stock control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
160mm T-Slot Bolt M24 T-Slot 28mm, Grade 8.8 DIN 787 - AMF
Rely on the proven combination of DIN 787 conformity, a M24 threaded shank and grade 8.8 strength for dependable clamping in industrial T‑slot systems; order the part directly via Metav Werkzeuge or consult our specialists for application guidance. AMF T‑nut screw DIN 787 — 28 mm T‑slot, M24 thread, 160 mm length A AMF T‑nut screw DIN 787 designed for secure clamping in 28 mm T‑slots, offering a metric M24 thread and a 160 mm overall length for deep anchoring in machine assemblies. High-strength grade 8.8 steel Metric M24 threaded shank Designed for 28 mm T‑slot rails 160 mm overall length for deep anchoring Precise standardisation for repeatable assembly Conformity to DIN 787 guarantees a standardised interface for T‑slot fastenings, enabling interchangeability across fixtures and machine tables. The combination of the M24 thread and the 28 mm T‑slot specification means the fastener aligns with common European profile systems, reducing measuring and alignment time during assembly. The supplied Axite addition values (A: 27.7; B: 110; E: 44; K: 18) describe the key seating and engagement dimensions, supporting accurate selection for specific rail geometries and helping to avoid trial‑and‑error fitting on the shop floor. Robust clamping performance that cuts downtime Constructed to grade 8.8 strength, the fastener delivers the tensile and yield characteristics required for demanding fixturing tasks. Its 160 mm overall length provides extended engagement for assemblies that require deeper anchoring or thicker clamping stacks, so fewer secondary supports are necessary. The result is a secure connection that maintains clamping force under repeated load cycles, reducing the frequency of retorquing and minimising production interruptions. For engineers and maintenance teams, the fastener represents a durable choice where consistent clamp integrity matters. Practical integration and reduced assembly effort Integration into existing setups is straightforward thanks to the part’s standard geometry and metric thread. The fastener arrives as single units (packaging unit: 1) and is catalogued under SKU 4000603257NW for easy procurement and inventory tracking. Clear technical dimensions and adherence to recognised norms simplify procurement decisions and accelerate assembly instructions for workshop staff. Where bespoke advice or dimensional confirmation is required, Metav’s technical team can advise on compatibility with specific rails and fixtures, ensuring correct selection for production or repair tasks. For procurement of the AMF T‑nut screw and personalised application advice, contact Metav Werkzeuge GmbH to confirm compatibility and arrange supply. Technical Data Article number: 4000603257NW Manufacturer: AMF Standard: DIN 787 Product type: T‑nut screw Thread: M24 T‑slot width: 28 mm Overall length: 160 mm Grade: 8.8 Packaging unit: 1 Dimensions & core data T‑slot: 28 mm Thread size: M24 Overall length: 160 mm Axite: A: 27.7 mm Axite: B: 110 mm Axite: E: 44 mm Axite: K: 18 mm Special features Conforms to DIN 787 for interchangeability High-strength grade 8.8 classification Single-unit packaging for controlled parts issue FAQ Is this fastener compatible with standard 28 mm T‑slot profiles? Yes. The T‑nut screw conforms to DIN 787 and is specified for a 28 mm T‑slot, making it compatible with common European T‑slot rails designed to that profile. What does the grade 8.8 designation indicate for performance? Grade 8.8 denotes a high‑strength steel classification with elevated tensile and yield properties; the AMF T‑nut screw is therefore suitable for demanding clamping tasks that require reliable load retention. Can this fastener be used for deep clamping stacks? Yes. With an overall length of 160 mm, the screw provides extended engagement for deeper clamping arrangements or thicker assemblies where additional anchoring length is beneficial. Where can the Axite dimensions be found and what do they mean? The Axite addition lists the manufacturing seating and engagement measures (A: 27.7; B: 110; E: 44; K: 18), which support precise selection for matching slot geometries and ensuring correct seating depth. What is the catalogue reference for procurement and stock management? The item is listed under SKU 4000603257NW, which should be used for ordering and inventory tracking to ensure accurate fulfilment. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
160mm T-Slot Screw 28mm M24 DIN 787 Grade 8.8 With Nut And Washer - AMF
Secure high-strength clamping with Grade 8.8 tensile performance, an M24 thread and a 160 mm overall length for deep fixtures in 28 mm T‑slots; order the component directly via Metav Werkzeuge or contact our consultants for tailored guidance. T-slot bolt DIN 787 — 28 mm T-slot, M24, 160 mm (AMF) The T-slot bolt DIN 787, 28 mm T‑slot, M24, 160 mm is a heavy-duty fastening solution for machine tables, fixture plates and modular clamping systems in metalworking environments. T‑slot 28 mm compatible M24 thread for heavy-duty clamping 160 mm overall length for deep fixtures Grade 8.8 strength with nut and washer Robust clamping for demanding fixtures This T‑slot bolt is designed to deliver reliable and repeatable clamping force where secure fixation matters. Conforming to DIN 787, the fastener ensures standardised geometry for insertion into a 28 mm T‑slot, while the M24 thread provides the purchase required for high‑tension applications. The supplied nut and washer reduce assembly steps and help achieve a consistent preload, which in turn lowers the risk of loosening during vibration. For production environments that prioritise uptime, this component supports safer, more stable fixturing and reduces fixture set‑up time through straightforward installation. Clear compatibility and installation guidance Compatibility is straightforward: the fastener fits T‑slots 28 mm and is intended for use with corresponding fixture plates and machine tables. The bolt’s 160 mm overall length accommodates deeper clamping stacks, enabling secure engagement through thick clamps or multiple shims. The supplied dimensional additions — A: 27.7 mm, B: 110 mm, E: 44 mm, K: 18 mm — give precise reference points for planning clamp heights and required thread engagement. These figures allow engineers and fitters to validate clearances and calculate the effective clamp thickness before assembly, reducing trial‑and‑error and streamlining set‑up procedures on the shop floor. Performance class and operational benefits Marked Grade 8.8, the fastener indicates a high mechanical performance suitable for many workshop and industrial clamping tasks. In practice, this means greater resistance to shear and tensile stresses compared with lower‑grade fasteners, supporting heavier loads and frequent tightening cycles. Using a standardised component such as this reduces variability in fixture performance and supports consistent quality control across multiple workstations. The inclusion of nut and washer with the bolt provides a ready‑to‑install assembly, simplifying inventory management and ensuring compatibility between parts supplied as a single unit. For project enquiries, bespoke advice or to secure fast and reliable delivery, contact Metav Werkzeuge GmbH in Emmerich: info@metav-werkzeuge.com or call +49 2822 7131930 — our team will assist with selection and supply. Technical data Article number: 4000833364NW Designation: T‑slot bolt DIN 787, 28 mm T‑slot, M24, L 160 mm Brand: AMF Packaging unit: 1 Core dimensions T‑slot width: 28 mm Thread: M24 Overall length: 160 mm Addition: A: 27.7 mm; B: 110 mm; E: 44 mm; K: 18 mm Special features Property class: Grade 8.8 Supplied with nut and washer Standard compliance: DIN 787 FAQ Is this fastener suitable for 28 mm T‑slots? Yes. The product is designed for 28 mm T‑slots and follows the DIN 787 form factors to ensure correct seating and engagement in compatible slots. What standard does the bolt conform to? The bolt is manufactured to DIN 787, which defines the geometry for T‑slot fasteners and supports interchangeability across standard machine tables and fixture systems. What is included in the delivery? Delivery includes the T‑slot bolt with the matched nut and washer, supplied as a ready assembly for immediate installation. Can the bolt handle heavy clamping loads? With a Grade 8.8 classification and an M24 thread, the fastener is suitable for heavy‑duty clamping applications commonly required on machine beds and fixture plates. Which dimensions should be considered when planning a clamp stack? Key dimensions are the 160 mm overall length and the addition measurements A: 27.7 mm, B: 110 mm, E: 44 mm, K: 18 mm, which help calculate available thread engagement and clamp height. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
160mm T-Slot Screw M16 With Nut And Washer, Grade 8.8, DIN 787 - AMF
Take advantage of a robust fastening solution that combines high tensile strength with precise T‑slot compatibility and ready-to-fit assembly. The Grade 8.8 construction and M16 metric thread ensure reliable clamping force while the 160 mm overall length and included nut and washer simplify installation — order directly via Metav Werkzeuge or consult the technical team for application advice. T‑slot screw DIN 787 — M16 × 160 mm, Grade 8.8 — AMF The T‑slot screw DIN 787 (16 mm T‑slot, M16 × 160 mm) by AMF is a high‑strength fastener designed for secure clamping in machine tool T‑slots, fixturing systems and modular fixtures. High-strength Grade 8.8 steel Fits 16 mm T‑slot profiles Metric M16 thread for standard components Supplied with nut and washer Engineered strength for industrial clamping The fastener meets DIN 787, offering a standardized geometry for insertion into machine table T‑slots. Manufactured to Grade 8.8, the screw is made for applications that require a dependable balance of tensile strength and ductility. In practice, this means consistent clamping performance under load and reduced risk of thread failure compared with lower grades. The combination of standardized form and rated material supports predictable assembly cycles and maintenance planning for production environments. Precision fit and straightforward assembly Designed for a 16 mm T‑slot and featuring an M16 metric thread, the component provides straightforward integration with common clamping elements and tooling accessories. Included nut and washer enable immediate use on delivery, reducing on‑site assembly steps. The provided axial dimensions — A 15.7, B 100, E 25, K 9 — describe the head and engagement geometry required to verify clearance and grip depth when planning a clamping setup; these values assist in avoiding interference and ensuring secure seating within the slot profile. Suitable for repeated production use and predictable maintenance A long overall length of 160 mm gives extended engagement where deep clamping is necessary, while the standardised thread and head form simplify spare‑part management. The robust construction and conformity to DIN reduce variability between batches, which supports higher uptime and fewer unplanned stops. For purchasers and maintenance planners, the fastener’s spec sheet aids in compatibility checks with vises, clamping levers and modular fixturing, making it easier to specify replacements or additions within existing tool inventories. Practical guidance and application notes When selecting fastening hardware for machine tables, verify slot width and depth, thread engagement length and the required clamping force for the application. The metric M16 thread is widely supported by standard nuts and threaded inserts, and the inclusion of a washer helps distribute flange loads and protect the slot surface. For specialised materials or high‑temperature environments, refer to application guidelines for suitable coatings or alternative grades; this variant is supplied in plain grade 8.8 steel without additional surface treatment as standard. For application support, custom enquiries or order placement, contact Metav Werkzeuge for technical advice and direct supply — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 4000833333NW Standard: DIN 787 Product: T‑slot screw, incl. nut and washer Brand: AMF UID: 4000833333NW Facts T‑slot width: 16 mm Thread: M16 Overall length: 160 mm Axial dimensions: A 15.7, B 100, E 25, K 9 Packaging unit: 1 Special features Grade 8.8 steel Supplied with nut and washer For machine table and fixture T‑slots Standardised form for modular fixturing FAQ What T‑slot width does this screw fit? The screw is specified for a 16 mm T‑slot; the head and engagement dimensions correspond to this slot size. Is a nut and washer included with the fastener? Yes, the delivery includes a nut and a washer to allow immediate assembly. Which standard governs the geometry of this fastener? The component conforms to DIN 787, ensuring standardised head and seating geometry for T‑slot applications. Can this screw be used with standard M16 accessories? The M16 metric thread matches common M16 nuts, threaded inserts and accessories used in workshop and industrial clamping. How do the axial dimensions A, B, E and K affect installation? The axial values (A 15.7, B 100, E 25, K 9) define head clearance and engagement length; these help determine slot clearance and maximum usable thread engagement. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16mm T-Slot Bolt M16 L125mm Grade 8.8, DIN 787 - AMF
Benefit from standardised fittings and consistent load capacity thanks to DIN 787 compliance and strength class 8.8; the combination of M16 threading and a 125 mm overall length delivers reliable clamping in 16 mm T‑slots. Order the T‑slot screw directly via Metav Werkzeuge or consult our specialists for specification advice. T‑slot screw (DIN 787) – M16, 16 mm T‑slot, L 125 mm, AMF T‑slot screw (DIN 787) designed for secure clamping in 16 mm T‑slot machine tables and fixtures DIN 787 standard compliance Fits 16 mm T‑slots M16 metric thread Strength class 8.8 Precise fit and repeatable clamping for machine tooling The DIN 787 specification ensures a repeatable, industry‑standard interface between the fastener and the table T‑slot, making installation straightforward and replacement predictable. With a 16 mm T‑slot designation and an M16 threaded shank, this fastener is intended for use where exact positional control and reliable shear performance matter. Engineers benefit from predictable geometry, reducing setup time and minimising downtime during fixture changes. Durable clamping performance under load Rated strength class 8.8, the fastener provides a balance of tensile strength and ductility suitable for many clamping scenarios on production equipment. The nominal overall length of 125 mm gives sufficient thread engagement for thick fixtures or stacked workpieces while maintaining a compact profile in the slot. Dimensional details for mounting and head clearance are given as A 15.7 mm, B 85 mm, E 25 mm, K 9 mm, supporting precise design of clamping assemblies and enabling faster CAD integration. Compatibility, handling and application notes Designed for workshop and industrial use, the bolt is suitable where a standard T‑slot anchoring solution is required—typical applications include machine tables, jigs and modular fixturing systems. The metric M16 thread allows compatibility with standard nuts and clamping hardware, preserving interchangeability across suppliers. Supplied as single units, the component from AMF supports small orders for maintenance spares as well as larger batch requirements when standardisation is a priority. Specify AMF T‑slot screws with DIN 787 geometry and strength class 8.8 via Metav Werkzeuge for consistent, workshop‑ready clamping—contact Metav Werkzeuge for ordering and technical guidance from Emmerich Technical Data Article number: 4000603223NW Product type: T‑slot screw (DIN 787) Manufacturer: AMF Facts T‑slot width: 16 mm Thread: M16 Overall length: 125 mm Packaging unit: 1 Special features Strength class: 8.8 Standard: DIN 787 Axite dimensions: A 15.7 mm; B 85 mm; E 25 mm; K 9 mm Brand: AMF FAQ What T‑slot size does this fastener fit? This fastener is designed for a 16 mm T‑slot and uses an M16 thread for anchoring. Is the product suitable for machine table clamping? Yes, the T‑slot screw (DIN 787) from AMF is intended for securing fixtures and workpieces on machine tables and modular fixturing. What does strength class 8.8 indicate for this screw? Strength class 8.8 denotes a high tensile rating suitable for many clamping tasks, offering a reliable balance of strength and toughness for securing components under load. Which standard governs the geometry of this fastener? The geometry follows DIN 787, the standard for T‑slot bolts and screws, ensuring interchangeability and conformity with tooling tables designed to that norm. How is the overall length measured for this item? The overall length is 125 mm, measured from end to end; this indicates available thread and shank length for assembly. Manufacturer: AMF; Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16mm T-Slot Bolt M16 L63mm Grade 8.8 With Nut And Washer, DIN 787 - AMF
Benefit from secure, standard-compliant clamping, robust Grade 8.8 strength and an M16 thread with a 63 mm overall length for reliable fixture assembly. Order directly via Metav Werkzeuge or consult our specialists for application advice. AMF T-slot bolt DIN 787 – M16 thread, 63 mm, Grade 8.8 A AMF T-slot bolt DIN 787 engineered for secure clamping in 16 mm T-slots, supplied complete with nut and washer for immediate installation DIN 787 standard compliance M16 metric thread 63 mm overall length Includes nut and washer Consistent clamping performance for production workflows The solid-design T-slot fastener delivers repeatable clamping results in modular fixture systems. With an M16 thread and 63 mm overall length, the fastener is suitable for standard workshop fixtures and machine tables that use a 16 mm T-slot. The metric thread enables straightforward torque control with common tools, translating into predictable clamp force and fewer setup iterations. Emphasis on measurable performance supports efficient production planning and reduces downtime during changeover. Engineered to fit DIN 787 T-slot systems precisely Compliance with DIN 787 ensures dimensional compatibility with established T-slot profiles, enabling straightforward integration into existing jigs and tables. The 16 mm slot specification and the supplied hardware remove ambiguity during part selection, allowing procurement and assembly teams to match components rapidly. Clear standard adherence also simplifies maintenance documentation and parts lists for long-term workshop reliability. Durable strength class for demanding clamping tasks Manufactured to Grade 8.8, this bolt offers high tensile capacity for secure fixturing under repeated load. The elevated strength class reduces the risk of fastener deformation during heavy clamping and contributes to longer service intervals for fixtures. Supplied nut and washer guarantee correct seating and load distribution, helping to protect both the bolt and the mounted workpiece while supporting consistent clamping behaviour across repetitive cycles. Practical dimensional data for correct selection and fit Detailed dimensional values aid precise selection: A: 15.7 mm, B: 45 mm, E: 25 mm, K: 9 mm. These figures support quick verification of clearance and engagement depth when designing or modifying clamping arrangements. The clearly defined metrics reduce trial-and-error during assembly and enable confident specification in procurement lists and CAD documentation, ensuring the component fits as intended the first time. For secure, standard-compliant clamping with AMF components, contact Metav Werkzeuge in Emmerich for tailored advice and fast supply — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 4000833329NW Product type: T-slot bolt Standard: DIN 787 Manufacturer: AMF SKU / UID: 4000833329NW Facts T-slot: 16 mm Thread: M16 Overall length: 63 mm A: 15.7 mm B: 45 mm E: 25 mm K: 9 mm Package unit: 1 Special features Grade 8.8 Includes nut and washer Addition: A: 15.7; B: 45; E: 25; K: 9 FAQ What T-slot size does this bolt fit? The bolt is designed for a 16 mm T-slot, compatible with standard DIN 787 profiles; see SKU 4000833329NW for full identification. Is a nut and washer included with the bolt? Yes, the AMF T-slot bolt DIN 787 is supplied complete with a nut and washer for immediate installation and correct load distribution. Which standard and thread form apply to this fastener? The fastener conforms to DIN 787 and features an M16 metric thread with an overall length of 63 mm. Is the bolt suitable for heavy-duty clamping? With a Grade 8.8 classification, the bolt provides high tensile strength appropriate for demanding clamping tasks and repeated fixture cycles; refer to SKU 4000833329NW when ordering. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18mm T-Slot Bolt M16 L80mm Grade 8.8 DIN 787 - AMF
Combine standard conformity and high clamping strength for reliable fixture assembly; the bolt’s DIN 787 geometry and Grade 8.8 rating ensure repeatable performance. Order the fastening element directly via Metav Werkzeuge or consult the team for application-specific advice. AMF T-slot bolt (DIN 787) – 18 mm T-slot, M16 x 80 mm, Grade 8.8 The AMF T-slot bolt (DIN 787) is a robust fastening element for slot-based clamping and fixture systems in machinery, jigs and workshop tooling. DIN 787 standardised design Suitable for 18 mm T-slots M16 threaded shank, 80 mm length High-strength Grade 8.8 steel Reliable clamping through standard conformity Conformity with DIN 787 provides assured interchangeability across slotted profiles and fixture systems, reducing adjustment time during set-up. The combination of an 18 mm T-slot profile with an M16 threaded shank and 80 mm overall length delivers a predictable engagement depth and consistent thread engagement. This standardised geometry supports quicker fixture changes and minimises the need for bespoke components, improving throughput in production and maintenance operations. The design focus is on functional reliability rather than decorative finish, ensuring secure seating and repeatable clamping in workshop and industrial environments. Engineered for strong performance and operational safety The fastener’s Grade 8.8 designation signals a high-strength specification suitable for demanding clamping tasks where elevated preload and resistance to loosening are required. The robust thread form and material grade permit confident torque application within common clamping practices, helping to maintain fixture integrity under vibration and dynamic loads. By choosing a high-strength fastener, operators gain enhanced safety margins for assemblies that experience cyclic stresses, while maintenance cycles can be planned with greater predictability. The technical advantage lies in converting the material and geometry into consistent clamping performance rather than relying on oversized components. Practical dimensions for efficient workshop integration Clear dimensional data supports inventory management and part matching: the product offers a compact overall length of 80 mm combined with slot compatibility for 18 mm profiles, simplifying selection for modular tooling systems. Additional published dimensions (A: 17.7; B: 55; E: 28; K: 10) assist in verifying clearance, head engagement and seating depth when integrating the bolt into existing fixturing. Supplied per single unit and identified by SKU 4000603228NW, the component is suited to both one-off repairs and systematic replenishment of maintenance stores, reducing downtime and streamlining parts logistics while keeping assembly workflows consistent. Contact Metav Werkzeuge for application guidance and stock details — expert advice and delivery from Emmerich is available to ensure the correct AMF T-slot bolt for each clamping task. Technical data Article number: 4000603228NW Label: T-Nutenschraube DIN 787 T-Nut 18mm M16 L.80mm Güte 8.8 AMF Manufacturer: AMF Product type: T-slot bolt SKU/UID: 4000603228NW Dimensions & thread T-slot width: 18 mm Thread: M16 Overall length: 80 mm Standard: DIN 787 Packing unit: 1 Additional dimensions: A: 17.7; B: 55; E: 28; K: 10 Special features Strength class: Grade 8.8 Suitable for slot-based clamping systems Designed for repeatable fixture assembly FAQ Is this bolt compatible with 18 mm T-slots? The AMF T-slot bolt (DIN 787) is designed for 18 mm T-slots and features an M16 thread and 80 mm overall length (SKU 4000603228NW) for direct integration into standard slotted profiles. Which standard does the fastening element conform to? Conformity to the DIN 787 standard ensures geometric compatibility and repeatable seating for the T-slot bolt across compliant clamping systems. What does Grade 8.8 indicate for this fastener? Grade 8.8 denotes a high-strength classification for the bolt, offering improved tensile and yield performance that supports elevated clamping forces and greater resistance to loosening under load. Are additional dimensions available for installation planning? Yes — the product includes auxiliary dimensions listed as A: 17.7; B: 55; E: 28; K: 10 to assist with clearance checks and head engagement during fixture design. How is the product packaged and identified? The bolt is supplied per unit (packing unit: 1) and can be ordered using SKU 4000603228NW for accurate replenishment and stock control. Manufacturer: AMF; Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm T-Slot Bolt M16 With Nut And Washer, DIN 787 - AMF
Take advantage of a robust, DIN‑compliant clamping solution that combines Grade 8.8 strength with an M16 thread and a 200 mm overall length for secure fixture retention in 18 mm T‑slots; order the assembly through Metav Werkzeuge or contact our specialists for compatibility advice. AMF T-slot bolt DIN 787 — M16 x 200 mm for 18 mm T-slot, Grade 8.8 A T-slot bolt by AMF for use in 18 mm machine table T‑slots, supplied complete with nut and washer for reliable clamping and straightforward installation DIN 787 compliant design Grade 8.8 high-tensile steel Fits 18 mm T-slots Supplied with nut and washer M16 thread, 200 mm overall length Reliable clamping performance for fixtures and tooling The DIN‑specified design ensures a predictable mechanical interface: compatibility with DIN 787 means the bolt aligns with common machine table tolerances and fixture systems, while the M16 thread gives a secure threaded engagement for standard clamping hardware. Manufactured to a Grade 8.8 classification, the connector offers a balance of tensile strength and ductility suitable for general workshop and industrial jigs, reducing the risk of slippage under load and supporting consistent setup repeatability. Precise fit and clear dimensional data for selection Detailed dimensional information supports quick selection and reduces trial‑and‑error. The assembly is intended for an 18 mm T‑slot and includes clear axial enrichment values (A: 17.7 mm; B: 125 mm; E: 28 mm; K: 10 mm) to confirm head and engagement geometry against existing fixtures. Supplied as a complete set with nut and washer, the component removes the need to source mating parts separately and simplifies inventory management on the shop floor, enabling faster cycle times during clamping operations. Built for workshop durability and dependable supply Engineered for repeated use in demanding environments, the bolt’s specification supports routine machining and fixturing tasks while offering long‑term serviceability. The combination of a standardised norm, robust thread form and included mounting hardware provides practical advantages: reduced setup time, lower risk of incompatible parts and predictable replacement intervals. Sourced via Metav Werkzeuge, the product benefits from an established European supply chain and quality control practices that help maintain a reliable parts stream for production and maintenance teams. For secure, DIN‑compliant clamping solutions, request a supply consultation from Metav Werkzeuge to confirm fit and delivery for the AMF T‑slot bolt (SKU 4000833341NW) and ensure seamless integration with existing machine tables Technical data SKU: 4000833341NW Label: T‑Nutenschraube DIN 787 T‑Nut 18mm M16 L.200mm Güte 8.8 m.Mutter u.Scheibe AMF Product type: T‑slot bolt Brand: AMF Norm: DIN 787 Dimensions & core data Thread: M16 Overall length: 200 mm T‑slot width: 18 mm Axial additions: A: 17.7 mm; B: 125 mm; E: 28 mm; K: 10 mm Packaging unit: 1 Special features Grade 8.8 high‑tensile classification Supplied with nut and washer Axial enrichment values included Suitable for standard machine T‑slots FAQ Is this bolt suitable for standard 18 mm machine table T‑slots? Yes. The AMF T‑slot bolt is designed specifically for an 18 mm T‑slot and conforms to DIN 787 to match common machine table specifications. What does Grade 8.8 indicate for this fastening element? Grade 8.8 denotes a high‑tensile steel classification that balances strength and ductility, offering dependable clamping performance for fixtures and general workshop applications. Does the delivery include all required fixing parts? The product is supplied complete with nut and washer as indicated in the product description, simplifying installation and spare‑part management. What are the axial enrichment values and why do they matter? The axial enrichment values (A: 17.7 mm; B: 125 mm; E: 28 mm; K: 10 mm) define head and engagement geometry; these dimensions aid in confirming clearance, head seating and thread engagement with existing fixtures. Is the bolt compatible with metric M16 clamping accessories? Yes, the M16 thread is a standard metric size and is compatible with typical M16 nuts and clamping accessories used in workshop fixturing. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm T-Slot Bolt M24 28mm T-Slot, Grade 8.8 DIN 787 - AMF
Take advantage of the standardised design and high tensile property class to ensure reliable clamping in machine tables; the combination of DIN 787 compliance and an M24 thread provides straightforward interchangeability and robustness — order directly via Metav Werkzeuge or consult the technical team for application advice. T-slot screw DIN 787 – 28 mm T-slot, M24 thread (AMF) The T-slot screw DIN 787 is a high-strength fastening solution for 28 mm T-slots, intended for machine tables, fixtures and heavy-duty clamping applications. DIN 787 standardised design Fits 28 mm T-slots M24 metric thread Grade 8.8 strength, 200 mm length Reliable standard conformity for seamless integration Compliance with DIN 787 ensures predictable dimensions and compatibility with industry-standard T-slot systems, which simplifies machine set-up and interchange of clamping elements. The standardised profile reduces measurement and fitting time during fixture changes and supports consistency across multiple workstations. As a result, downtime is minimised and procurement becomes more efficient, since replacement parts conform to an established European norm. High-strength performance and secure clamping The Grade 8.8 property class and the M24 metric thread deliver a robust combination of tensile strength and reliable torque transmission, suitable for heavy clamping forces on machine tables and modular fixturing. With a 200 mm overall length the fastener allows deeper engagement where extended bite is required. The coarse M24 thread supports strong preload while remaining serviceable with standard tooling, helping to keep maintenance straightforward and predictable. Practical fit and application guidance for workshop use Designed for a 28 mm T-slot and specified with precise axial dimensions (A: 27.7, B: 125, E: 44, K: 18), the component offers a secure seating and correct alignment in slot-mounted assemblies. Packaged per unit, the fastener is suited to single-component replacements or staged upgrades of clamping systems. Selection should match slot width and fixture geometry; when in doubt, consult the technical data to confirm compatibility with the machine table and clamping hardware being used. Contact Metav Werkzeuge for precise ordering and application support: info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability and delivery from Emmerich Technical data Article number: 4000603258NW SKU / UID: 4000603258NW Standard: DIN 787 Product type: T-slot screw Brand: AMF Facts T-slot width: 28 mm Thread: M24 Overall length: 200 mm Property class: 8.8 A: 27.7 B: 125 E: 44 K: 18 Packaging unit: 1 Special features Designed for machine tables and fixturing Standardised dimensions for interchangeability Heavy-duty fastening for clamping applications FAQ Is this fastener compatible with standard 28 mm T-slots? Yes. The T-slot screw DIN 787 (AMF) is specified for 28 mm T-slots and includes axial dimensions to ensure correct seating in standard slot systems. What does Grade 8.8 indicate for the screw? Grade 8.8 denotes a high-strength property class; the T-slot screw by AMF provides enhanced tensile and yield performance suitable for demanding clamping tasks. Can the fastener be used on modular fixture plates with deeper threaded engagement? Yes. The 200 mm overall length allows deeper engagement where required; consideration of thread engagement depth and slot clearance is recommended before installation. Which thread size is used and what tooling is needed? The component features an M24 metric thread; standard M24 tooling and torque practices for Grade 8.8 fasteners apply for installation and removal. What is the article number for ordering and reference? The article number is 4000603258NW (T-slot screw DIN 787, AMF), which should be quoted for precise procurement and documentation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm T-Slot Screw 22mm M20 DIN 787 Grade 8.8 - AMF
Take advantage of the combination of standardised fit, robust tensile performance and straightforward installation for reliable clamping in production setups; order the part directly via Metav Werkzeuge or contact our consultants for specification support. AMF T-slot bolt DIN 787 — 22 mm T-slot, M20, 200 mm, Grade 8.8 AMF T-slot bolt DIN 787 is a heavy-duty clamping element for 22 mm T-slots, designed for secure fixture assembly and machine-table fastening in industrial environments. Compliant with DIN 787 Fits 22 mm T-slots M20 thread, 200 mm length Grade 8.8 high tensile strength Secure clamping performance for machine tables The bolt provides a reliable mechanical interface for machine tables and modular fixturing thanks to its compatibility with 22 mm T-slots and an M20 threaded connection. These properties ensure a consistent and repeatable clamping action, which reduces setup time and minimises micro-movement under load. The overall length of 200 mm gives sufficient thread engagement for deep assemblies, while the standardised head geometry is intended to sit securely within the slot profile, improving positional stability during machining and assembly operations. Standardised fit for seamless interchangeability Manufactured to DIN 787, the component offers a predictable fit and geometry that simplifies parts replacement and system integration. The adherence to this norm means the head dimensions and slot interface are compatible with other DIN-conformant accessories, enabling quick interchange without bespoke adapters. For procurement and maintenance planning, the use of standardised elements reduces the risk of mismatches and supports consistent inventory management across workshops and production lines. Strength and durability suitable for demanding applications Specified as Grade 8.8, the fastener delivers elevated tensile and yield characteristics compared with lower-grade alternatives. This classification indicates enhanced resistance to shear and bending stresses encountered in heavy clamping scenarios, making the bolt suitable for medium to high-load fixtures. Where cyclic loads or vibration are present, selecting a high-tensile fastener like this reduces the likelihood of deformation and contributes to longer service intervals and fewer unplanned stoppages. Interface details and dimensional guidance Key interface dimensions are provided to aid design and assembly: additional dimensional values are A: 21.7 mm, B: 125 mm, E: 35 mm, K: 14 mm, which describe the head and engagement geometry for integration into standard clamping systems. These measured parameters support designers and engineers in verifying clearance, reach and engagement depth when planning fixture layouts or retrofitting new components into existing equipment. Practical installation and system compatibility The threaded M20 connection accepts widely available nuts and washers, allowing standard fastening practices to be applied. The fastener's design supports straightforward installation: insert into the 22 mm slot, align with the workpiece or clamp element, and secure using appropriate torque values for Grade 8.8 hardware. Where required, confirm torque and assembly procedures with tool manufacturers to ensure clamping force is consistent and safe for the application. Specification support and procurement assurance For procurement teams and workshop managers, the use of standardised, robust fasteners simplifies sourcing and reduces the variety of parts to be stocked. Metav’s role as a precision partner ensures that components are supplied reliably from the Emmerich hub, with quality controls aimed at delivering consistent product performance and traceable deliveries for production-critical hardware. For reliable supply of AMF Grade 8.8 T-slot bolts and expert advice on integrating them into existing fixtures, contact Metav Werkzeuge for immediate assistance at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: 4000603245NW SKU: 4000603245NW Standard: DIN 787 Core measurements T-slot width: 22 mm Thread: M20 Overall length: 200 mm Grade: 8.8 Additional dimensions: A 21.7 mm, B 125 mm, E 35 mm, K 14 mm Features Product type: T-slot bolt Brand: AMF Packaging unit: 1 FAQ What slot size does the bolt fit? The bolt is designed for a 22 mm T-slot, providing a standardised fit for compatible machine tables and fixtures. Which thread and length are specified for this T-slot bolt? This fastening element has an M20 thread and an overall length of 200 mm, suitable for assemblies requiring extended engagement. Is the bolt manufactured to any recognised standard? Yes, the bolt conforms to DIN 787, ensuring standard head geometry and interchangeability with other DIN-compliant components. What does Grade 8.8 mean for performance? Grade 8.8 indicates elevated tensile strength and yield properties, making the bolt suitable for demanding clamping scenarios where higher load resistance is required. How can engineers verify dimensional compatibility? Use the provided dimensions A 21.7 mm, B 125 mm, E 35 mm and K 14 mm to confirm head and engagement geometry against fixture drawings and slot profiles. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm T-Slot Screw M20 With Nut And Washer, DIN 787 8.8 - AMF
Take advantage of a robust fastener that combines DIN 787 compliance with Grade 8.8 strength and a 200 mm reach for reliable fixturing; order directly via Metav Werkzeuge or consult our specialists for application advice. AMF T-slot screw DIN 787 — M20 thread, 200 mm, Grade 8.8 AMF T-slot screw DIN 787 for secure clamping in 20 mm T-slots, supplied complete with nut and washer for machine tables and fixture systems Conforms to DIN 787 T-slot standard Designed for 20 mm T-slot systems High-strength Grade 8.8 construction Supplied with nut and washer Secure clamping through standard compliance The DIN 787 specification guarantees standardised geometry for T-slot fasteners, enabling predictable assembly and interchangeability across machines and fixture plates. By meeting this norm, the M20 threaded fastener provides a verified interface that reduces alignment issues and speeds up setup. The standardised form also simplifies procurement and stock management in production environments, allowing planners to rely on consistent fit and function. Size and reach tailored for demanding fixtures With a 200 mm overall length and compatibility with a 20 mm T-slot, the screw is engineered to reach through thicker plates and clamping stacks while maintaining a secure thread engagement. The combination of M20 thread and extended shank length enables deeper clamping and flexibility in fixture design. Dimension references (A: 19.7; B: 125; E: 32; K: 12) support precise integration into assemblies and help machine planners verify clearances and gripping depths before installation. Proven strength for industrial use Constructed to Grade 8.8, the fastener delivers a balance of tensile strength and toughness suitable for heavy clamping applications. This property class indicates quenched and tempered steel performance levels commonly used in workshop and production settings to resist shear and tensile loads. The result is a dependable connection that maintains clamping force under cyclical loads, contributing directly to process stability and reduced rework. Ready-to-install delivery reduces assembly time Delivered complete with nut and washer, the fastener removes the need to source matching components separately, shortening the assembly chain and simplifying logistics. Packaged as a single unit, the product supports just-in-time workflows and minimises inventory complexity. The supplied fixing elements are matched to the thread size to ensure correct fit and reliable torque transmission during tightening. For reliable fixturing with AMF’s high-strength T-slot fastener, contact Metav Werkzeuge for ordering and bespoke advice — Metav Werkzeuge can confirm suitability for specific machine tables and provide delivery from Emmerich: info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 4000833347NW SKU / UID: 4000833347NW Standard: DIN 787 Product type: T-slot screw Brand: AMF Thread: M20 T-slot width: 20 mm Total length: 200 mm Grade: 8.8 Includes: nut and washer Packaging unit: 1 Facts Thread size: M20 T-slot compatibility: 20 mm Overall length: 200 mm Dimension A: 19.7 Dimension B: 125 Dimension E: 32 Dimension K: 12 Standard: DIN 787 Special features Conforms to DIN 787 T-slot geometry High-strength Grade 8.8 fastener Supplied complete with matched nut and washer Suitable for machine tables and fixture systems FAQ What T-slot width is this fastener suitable for? The AMF T-slot screw is designed for a 20 mm T-slot, matching the DIN 787 profile for secure seating in standard machine table grooves. Does the delivery include fixing hardware? Yes, the product is supplied with a matched nut and washer, allowing immediate installation without sourcing additional components. What is the thread size and overall length of the fastener? The fastener features an M20 thread and an overall length of 200 mm, suitable for deeper clamping applications. Which standard does the screw comply with? This T-slot screw conforms to DIN 787, ensuring standardised geometry for compatibility across machines and fixtures. Can the SKU be used to order the exact item? Orders and enquiries can reference SKU 4000833347NW to ensure the correct AMF T-slot screw is supplied. Manufacturer: AMF; Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
22mm T-Slot Bolt M20 L125mm Grade 8.8 With Nut And Washer, DIN 787 - AMF
Take advantage of a DIN 787‑compliant design combined with an M20 thread and 125 mm overall length for robust, repeatable clamping in T‑slot applications; the fastener’s strength class 8.8 and delivery with nut and washer ensure reliable assembly and reduced procurement steps. Order the AMF T‑slot screw directly via Metav Werkzeuge or consult our specialists for specification support. AMF T‑slot screw DIN 787 – 22 mm T‑slot, M20 x 125 mm, grade 8.8 A T‑slot screw designed for secure fixturing in 22 mm T‑slots, offering standardised dimensions and industrial strength for machine tables and clamping systems. DIN 787 standardised dimensions M20 thread for high clamping force 125 mm overall length for deep fixtures Includes nut and washer for direct use Reliable performance for production clamping The fastener conforms to DIN 787, which defines the geometry and fit for T‑slot bolts used in machine tables and fixtures. The M20 thread combined with a 125 mm overall length provides a high clamping leverage and makes tightening procedures predictable under service conditions. Specified as strength class 8.8, the component offers a balance of tensile strength and toughness suitable for routine industrial use, reducing downtime caused by fastener failure and ensuring consistent part alignment during machining or assembly processes. Compact handling and immediate fitment benefits Supplied complete with nut and washer, the assembly is ready for immediate installation, eliminating the need to source hardware separately and speeding up fixture changes. The 22 mm head profile is matched to standard T‑slot widths for a secure, anti‑rotation fit, which improves repeatability in production set‑ups. Where quick changeovers are required, the standardised form factor simplifies inventory management and reduces time spent on assembly preparation. Robust choice for workshops and production lines Chosen for its standardized geometry and proven strength class, this T‑slot fastener supports reliable clamping across a wide range of applications from toolroom jigs to shop‑floor fixtures. The combination of DIN compliance, thread size and included fastening elements contributes to a predictable service life and lower overall maintenance effort. For buyers seeking an efficient supply route, the item aligns with Metav’s emphasis on accessible precision and dependable delivery. For procurement or technical selection of AMF T‑slot screws, contact Metav Werkzeuge for tailored advice and reliable supply coordination via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 4000833352NW SKU / UID: 4000833352NW Standard: DIN 787 Brand: AMF Facts Thread: M20 T‑slot compatibility: 22 mm Overall length: 125 mm Packaging unit: 1 Special features Strength class: 8.8 Delivered with nut and washer Product type: T‑slot screw Axial enrichments: A: 21.7; B: 85; E: 35; K: 14 FAQ What T‑slot width does this fastener fit? This T‑slot screw is designed for a 22 mm T‑slot and matches the standard head geometry specified under DIN 787. Does the delivery include fastening hardware? Yes, the AMF T‑slot screw is supplied with nut and washer, ready for immediate assembly. What do DIN 787 dimensions guarantee? DIN 787 ensures standardised head and shank geometry for T‑slot bolts, so the fastener will fit correctly into machine tables and clamping rails compliant with the same standard. Which thread and length are specified for this fastener? The component uses an M20 thread and an overall length of 125 mm, suitable for deeper fixture requirements. How is the item packaged? The product is supplied in a packaging unit of 1. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
250mm T-Slot Bolt 18mm M16 with Nut and Washer, Grade 8.8 - AMF
Take advantage of a robust combination of standard-compliant specification and dependable tensile performance: the bolt’s conformity to DIN 787, the M16 thread and property class 8.8 deliver secure clamping in 18 mm T-slots, while the supplied nut and washer reduce procurement steps — order the fastener directly via Metav Werkzeuge or consult the specialists for application advice. T-slot bolt DIN 787 — 18 mm T-slot, M16, L 250 mm (AMF) T-slot bolt DIN 787 — 18 mm T-slot, M16, L 250 mm (AMF) is a heavy-duty fastener designed for secure fixture in standard 18 mm T-slots across machine tables, modular frames and tooling assemblies Compatible with 18 mm T-slots M16 metric coarse thread for high load Property class 8.8 high tensile steel Supplied complete with nut and washer Consistent strength and conformity for repeatable clamping The fastener is manufactured to DIN 787, ensuring dimensional conformity and interchangeability with industry-standard T-slot profiles. The combination of an M16 thread and property class 8.8 denotes a high-tensile steel component capable of sustaining reliable clamping forces in demanding workshop and industrial settings. For production planners and workshop managers this translates into predictable assembly behaviour and easier specification across fixtures and jigs, reducing the need for custom fasteners and avoiding unexpected fit issues during installation. Precise dimensions that simplify assembly planning With an overall length of 250 mm and compatibility with 18 mm T-slot profiles, the component provides ample thread engagement to accommodate thicker fixtures or stacked plates. The supplied axial dimension data (A: 17.7; B: 150; E: 28; K: 10) supports precise clearance and insertion planning during fixture design. Clear, verifiable dimensions allow technical teams to calculate clamping ranges and torque settings before procurement, which shortens assembly preparation time and lowers the risk of rework on the shop floor. Fewer procurement steps thanks to included fittings The delivery includes a nut and washer, enabling immediate use without sourcing complementary parts separately. This reduces procurement complexity and minimises downtimes caused by missing components. For maintenance and repair cycles, keeping a small stock of this complete fastener reduces the number of SKU variants needed, offering a straightforward logistics advantage for service teams and purchasing departments alike. Typical applications and handling recommendations The T-slot fastener is suitable for machine table fixtures, modular fixturing systems, jigs and clamping setups where an 18 mm groove is present. Installation requires a compatible T-slot runner and adequate thread engagement; tightening should follow the fixture design’s specified torque values to ensure secure clamping without overstressing the bolt. The standardised dimensioning supports modular interchangeability, allowing the same component to be reused across multiple assemblies and promoting a leaner spare-parts inventory. For reliable fastening with AMF quality and property class 8.8 performance, contact Metav Werkzeuge in Emmerich for tailored advice and procurement via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 4000833342NW Standard: DIN 787 Product type: T-slot bolt Brand: AMF Includes: nut and washer Facts Thread: M16 T-slot width: 18 mm Overall length: 250 mm Property class: 8.8 Axial dimensions: A: 17.7; B: 150; E: 28; K: 10 Packaging unit: 1 Special features Conforms to DIN 787 Supplied complete for immediate use Suitable for machine tables and modular fixturing High-tensile classification for secure clamping FAQ What does conformity to DIN 787 mean for fittings? Conformity to DIN 787 ensures the T-slot bolt matches standardised dimensions for insertion and seating in 18 mm grooves, so assemblies using the component benefit from predictable fit and interchangeability. Which slot width is required for this fastener? This fastener is designed for an 18 mm T-slot; the specified geometry provides proper seating and load distribution when used with compatible slot runners. What performance can be expected from property class 8.8? Property class 8.8 indicates a high-tensile steel classification suitable for substantial clamping forces; this grade balances strength and ductility for general industrial fastening tasks. Is the bolt supplied ready for installation? Yes — the delivery includes a nut and washer, enabling immediate assembly without sourcing additional standard fittings. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
40mm T-Slot Bolt M10 Strength Class 10.9, DIN 787 - AMF
Take advantage of the combination of industrial standard conformity, M10 compatibility and grade 10.9 strength for dependable fixture clamping; order directly via Metav Werkzeuge or consult the team for specification advice. T-slot screw DIN 787 — 10 mm T-slot, M10 x 40 mm (AMF) The T-slot screw DIN 787 is a high-strength clamping fastener designed for securing fixtures and tooling in 10 mm machine table T-slots. DIN 787 standard for industrial compatibility High-strength grade 10.9 for secure clamping M10 metric thread for standard tooling Fits 10 mm T-slots, overall length 40 mm Consistent clamping force through recognised standardisation The use of the DIN 787 specification ensures a predictable interface between table, clamp and fastener, reducing setup variance across repeated assemblies. Manufactured to grade 10.9, the screw offers high-strength characteristics that translate into greater clamp preload and less loosening under vibration; this is particularly relevant for medium- to heavy-duty machining where steady holding power matters. The metric M10 thread provides broad compatibility with standard clamping hardware and makes replacement straightforward when maintenance is required. Precise fit in 10 mm T-slots for repeatable setups A precise geometry for the 10 mm T-slot combined with an overall 40 mm length gives a reliable engagement depth for clamps and support elements, promoting repeatable positioning of workpieces. The head and shank geometry create a secure mechanical seat inside the slot, which limits lateral play and supports accurate fixturing. For workshop planners and production engineers, this means shorter setup times and fewer adjustments between jobs, contributing directly to process efficiency and uptime. Reliability and integration for workshop use Built to perform as part of standard fixturing systems, this fastener supports modular clamping concepts and integrates easily with existing tooling plates and clamps. The robust mechanical properties reduce the frequency of fastener replacements, helping to maintain a steady production rhythm. Sourcing through an established distributor further ensures consistent supply and traceability, which aids quality control processes and procurement planning in assembly and machining environments. For procurement or technical advice on AMF grade 10.9 T-slot screws, contact Metav Werkzeuge for tailored support and supply information at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: 4000603196NW Standard: DIN 787 Product: T-slot screw Thread: M10 T-slot size: 10 mm Length: 40 mm Strength class: 10.9 Manufacturer: AMF Packaging unit: 1 Dimensions & measurable data Addition A: 9.7 Addition B: 30 Addition E: 15 Addition K: 6 Special features Metric thread for standard fixtures Conforms to DIN 787 for interchangeability High-strength class for secure clamping Suitable for machine table fixturing FAQ What T-slot size does this screw fit? This T-slot screw fits a 10 mm T-slot and is dimensioned for reliable seating in that slot size. What does grade 10.9 signify for this fastener? Grade 10.9 indicates a high-strength fastener class; the AMF T-slot screw in 10.9 offers elevated tensile strength and improved clamp retention compared with lower classes. Is the thread standard metric M10? Yes, the screw uses an M10 metric thread, ensuring compatibility with common nuts and clamping components. Can this screw be used for heavy-duty clamping on machine tables? The high-strength class and DIN 787 conformity make this screw suitable for demanding fixturing tasks on machine tables. What is the overall length and how does it affect fixture selection? The overall length is 40 mm, which determines the maximum clamping thickness and should be matched to clamp and workpiece stack-up. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
50mm 12mm T-Slot Screw M12 Grade 10.9 With Nut And Washer, DIN 787 - AMF
A compact solution for secure fixture clamping: the M12 T-slot screw meets DIN 787 and offers high tensile grade 10.9 strength in a 50 mm length for reliable tool-holding; supplied complete with nut and washer for immediate installation. Order the T-slot screw directly via Metav Werkzeuge or ask our consultants if needed. T-slot screw DIN 787 — M12 x 50 mm, grade 10.9 (AMF) T-slot screw DIN 787 for 12 mm T-slots, designed for secure clamping in machine tables, fixtures and tooling plates T-slot screw »4000833309NW« by AMF DIN 787 standard for secure clamping M12 thread for 12 mm T-slots Grade 10.9 strength, incl. nut and washer Robust clamping performance for workshop and production The fastener conforms to DIN 787, ensuring a standardised fit for machine tables and fixture systems. With an M12 thread matched to a 12 mm T-slot and an overall length of 50 mm, the screw provides consistent thread engagement and repeatable clamping force. The grade 10.9 designation signals elevated tensile and yield strength compared with lower grades, which reduces elongation under load and helps prevent fixture movement during machining. This combination of standard conformity and mechanical strength supports reliable production processes and minimises rework. Ready-to-install design reduces assembly time Delivered with a matched nut and washer, the fastener arrives as a complete clamping solution ready for immediate use on standard T-slot tables. The single-length configuration simplifies parts handling and inventory, while the screw geometry is optimised for insertion into 12 mm slots without additional modification. Because the item is supplied as a set, workshop staff can complete jigs and fixtures faster, reduce downtime between set-ups and keep cycle times predictable — practical benefits for both one-off jobs and repetitive production runs. Proven quality and supply assurance for industrial use Produced under the AMF designation, this screw is traceable by SKU 4000833309NW and intended for demanding assembly and tooling tasks. The robust mechanical properties and standardised dimensions make it suitable for use across milling machines, drilling rigs and modular fixture systems where consistent clamping is required. Metav’s distribution ensures a dependable supply channel and a quality filter at the European hub in Emmerich, supporting long-term availability and straightforward replenishment for professional workshops and industrial buyers. For AMF-grade clamping reliability and quick technical advice, contact Metav Werkzeuge in Emmerich — ordering and consultancy are available via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 4000833309NW Label: T-slot screw DIN 787 M12 x 50 mm grade 10.9 incl. nut and washer Brand: AMF Numbers / Core technical data Thread: M12 T-slot width: 12 mm Overall length: 50 mm Strength class: 10.9 Packaging unit: 1 Special features / Versions Conforms to DIN 787 Supplied with nut and washer SKU for ordering: 4000833309NW Axite enrichment values: A: 11.7; B: 35; E: 18; K: 7 FAQ What standard does this T-slot screw meet? The item complies with DIN 787, which defines dimensions and profiles for T-slot screws used in machine tables and fixtures. Which thread and T-slot size are suitable for this screw? The screw carries an M12 thread and is designed specifically for 12 mm T-slots, providing standardised compatibility with machine tables. Is the nut and washer included in delivery? Yes, the T-slot screw is supplied complete with the matching nut and washer so it is ready for immediate installation. What is the overall length and strength class? Overall length is 50 mm and the fastener is manufactured to grade 10.9, offering higher tensile strength for demanding clamping tasks. How can the product be identified when ordering? Use SKU 4000833309NW or the label reference for ordering and stock enquiries. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
50mm T-Slot Bolt M12 With Nut And Washer DIN 787 Grade 10.9 - AMF
Take advantage of a high-strength T-slot fastening solution that combines DIN 787 compliance, reliable M12 threading and a grade 10.9 specification for secure clamping; order the part directly via Metav Werkzeuge or consult their specialists for compatibility advice. AMF T-slot bolt, DIN 787 — M12 thread, 14 mm T-slot, 50 mm length AMF T-slot bolt for secure clamping in 14 mm T-slots; supplied complete with nut and washer for immediate fitting in workshop and machine tool applications. T-slot bolt to DIN 787 standard 14 mm T-slot compatibility M12 metric thread, 50 mm overall length Strength grade 10.9; incl. nut and washer Secure, standardised fastening for machine tables The DIN 787 compliant design ensures consistent geometry and interchangeability across machine tables and fixtures. Manufactured to meet a recognised metric standard, this T-slot fastener delivers predictable seating and clamping behaviour when used in compatible 14 mm T-slots. The standard conformity simplifies procurement and inventory management by aligning with established workshop norms, while the included nut and washer permit immediate installation without sourcing additional components. High clamping reliability and material performance Specified as grade 10.9, the fastener offers elevated tensile strength compared with lower-grade alternatives, translating into improved resistance to shear and elongation under load. The M12 thread provides a common metric interface for many clamping elements and tooling accessories, supporting reliable torque transmission and repeatable clamp forces. For routine assembly, the combination of thread size and grade results in a robust connection suited to demanding machining and fixture applications where secure workholding is essential. Practical dimensions and straightforward integration With a clear overall length of 50 mm and compatibility with 14 mm T-slots, this fastener integrates cleanly into standard clamping setups without modification. The additional axite specification (A: 13.7; B: 35; E: 22; K: 8) gives precise dimensional guidance for designing or verifying fixture clearances and seating depths. These numeric details aid planning for toolpaths, guard clearance and component layout, reducing set-up time and supporting efficient production workflows. Contact Metav Werkzeuge for tailored advice on integrating the AMF T-slot bolt (SKU 4000833316NW) into existing fixturing systems or to request a technical quotation and delivery options Technical data Article number: 4000833316NW Standard: DIN 787 Product type: T-slot bolt Brand: AMF Thread: M12 T-slot width: 14 mm Overall length: 50 mm Strength grade: 10.9 Includes: nut and washer Packaging unit: 1 Axite addition: A: 13,7; B: 35; E: 22; K: 8 Numbers / facts T-slot width: 14 mm Thread size: M12 Length: 50 mm Strength: grade 10.9 SKU: 4000833316NW Axite values: 13.7 / 35 / 22 / 8 Special features / versions DIN 787 compliant geometry Supplied with nut and washer for immediate use Designed for workshop and machine tool clamping applications AMF brand component FAQ What machine table slots is this fastener compatible with? The AMF T-slot bolt is designed for 14 mm T-slot systems and follows DIN 787 geometry to ensure compatibility with standard machine tables and fixtures. Can this fastener withstand high clamping loads? Yes; the bolt is specified as grade 10.9, which provides high tensile strength and reliable performance under significant clamping forces when tightened to the appropriate torque for an M12 thread. Is the fastener supplied ready for installation? The delivery includes the T-slot bolt together with a nut and washer for immediate fitting, allowing installation without the need to source additional fastening parts. Are there detailed dimensions for fixture planning? Dimensional guidance is provided via the axite values (A: 13.7; B: 35; E: 22; K: 8) and the core measurements (14 mm T-slot, M12 thread, 50 mm length), which assist in checking seating depth and clearance. What is the SKU for ordering and reference? The product is listed under SKU 4000833316NW, referenced as an AMF T-slot bolt to DIN 787, M12, 50 mm. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com