13mm Flat Magnetic Gripper With Threaded Bush 10N Holding Force, Up To 200 °C - TECWERK
Compact, space-saving holding with a 13 mm diameter, M3 threaded bush and a 10 N holding force ensures dependable positioning in small fixtures; the low-profile 11.5 mm height supports tight assemblies while recommended temperatures up to 100 °C (max 200 °C) expand use cases. Order directly via Metav Werkzeuge or consult their specialists for integration advice. TECWERK Magnetic Flat Gripper D.13×H11.5mm — M3 Thread, 10 N Holding Force The magnetic flat gripper D.13×H11.5mm is a compact flat magnetic holder engineered for light-duty holding and precise positioning in assembly, fixture and small-part handling applications Compact 13 mm diameter Secure M3 threaded bush mounting Max holding force 10 N Temperature resistant up to 200 °C Space-saving holding that simplifies fixtures and jigs A low-profile design delivers efficient fixation in constrained assemblies: the 13 mm diameter and 11.5 mm height reduce interference in tight setups, while the holding force 10 N secures small components without bulky hardware. The combination of compact dimensions and measurable holding performance allows engineers to replace more complex clamping parts with a simple magnetic solution, reducing setup time and simplifying repetitive positioning tasks. This results in faster cycle times and fewer handling operations in production environments. Robust magnetic material and reliable threaded mounting Manufactured from hard ferrite, the magnet offers stable magnetic properties suited to frequent, light-duty use. The integrated M3 thread in the threaded bush enables direct, repeatable attachment to plates, brackets or small fixtures, ensuring secure mounting and straightforward integration into existing tooling. The component is recommended up to 100 °C and remains temperature resistant up to 200 °C for temporary excursions, making the unit adaptable to processes with moderate heat exposure while preserving holding performance over time. Practical applications and operational advantages Ideal for assembly, positioning of small parts, light automation end-effectors and jig construction, this flat magnetic holder reduces mechanical complexity while improving handling consistency. The simple geometry facilitates quick replacement and minimal maintenance, delivering a pragmatic way to enhance throughput without redesigning fixtures. For technical clarity and integration planning, assistance is available for selecting the correct specification and mounting approach to match specific production requirements. For tailored recommendations and local supply of TECWERK magnetic flat grippers, contact Metav Werkzeuge for professional guidance and parts provision from Emmerich. Technical data Article number: 4000832241NW Manufacturer: TECWERK Product: Magnetic flat gripper Version: with threaded bush Material: hard ferrite Facts Diameter: 13 mm Height: 11.5 mm Thread: M3 Holding force: 10 N Recommended operating temperature: up to 100 °C Maximum operating temperature: 200 °C Special features With threaded bush Hard ferrite magnet Light-duty holding and positioning Packaging unit: 10 Label: Magnetflachgreifer D.13xH11,5mm m.Gewindebuchse Haftkraft 10N FAQ What material is used for the magnet? The TECWERK magnetic flat gripper is made from hard ferrite, a stable ceramic magnet material suited to light-duty holding applications. What holding force can be expected from this gripper? The magnetic flat gripper provides a holding force of 10 N, sufficient for securing small components in positioning and fixture tasks. How is the gripper mounted? Mounting is via the integrated M3 threaded bush; the M3 thread allows secure attachment to brackets or fixture plates. Can the gripper be used at elevated temperatures? The flat magnetic gripper is recommended for continuous use up to 100 °C, with a maximum short-term resistance up to 200 °C. Which applications suit this magnetic holder best? Typical uses include assembly stations, small-part fixturing, light automation end-effectors and any setup requiring compact, repeatable magnetic holding. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
13mm Magnet Flat Gripper H4.5 No Threaded Insert Holding Force 10N - TECWERK
Take advantage of a compact, heat-resistant design combined with reliable holding power for repeatable fixturing and assembly tasks. Order the magnetic component directly via Metav Werkzeuge or consult the specialists for compatibility and supply from Emmerich. Magnetic flat gripper D13 x H4.5 mm without threaded sleeve – 10 N holding force (TECWERK) A Magnetic flat gripper D13 x H4.5 mm without threaded sleeve designed for precise, low-profile holding in assembly, jigs and fixture applications where a compact and heat-tolerant magnetic base is required Hard ferrite construction for corrosion resistance 10 N maximum holding force Compact Ø13 x H4.5 mm flat design Rated for up to 200 °C peak temperature Precise, repeatable holding in a compact form The flat magnetic base combines a hard ferrite core with a low-profile geometry to deliver consistent 10 N holding force in a space-saving package. The compact Ø13 x H4.5 mm footprint enables secure support of small ferrous parts within tight assemblies and precision jigs. The magnet’s flat design simplifies placement on planar surfaces and reduces unwanted protrusion, which benefits automated stations and manual workstation setups alike. Magnetic behaviour is predictable, aiding process planning and fixture repeatability. Thermal resilience for elevated-process applications Specified with a recommended operating temperature of up to 100 °C and a maximum peak tolerance of 200 °C, the component maintains magnetic stability during brief exposure to elevated temperatures. This characteristic supports short-duration thermal processes such as soldering or pre-heating sequences where a temporary magnetic hold is required. The temperature ratings allow integration into workflows that include heating steps, while the hard ferrite material ensures dimensional stability and long-term performance under typical workshop conditions. Easy integration and inventory efficiency The version without threaded sleeve provides a flush contact surface for direct mounting or embedding into fixtures where external threading is undesired. Supplied in packing unit 10, the item suits small-series production and maintenance replenishment without excessive stock. The plain design minimises machining effort for bespoke fixture blocks and simplifies replacement in service scenarios. Material choice and compact format contribute to a cost-effective solution for securing lightweight ferrous components during machining, inspection or assembly steps. Contact Metav Werkzeuge for specification support and supply from Emmerich — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 4000832231NW SKU: 4000832231NW Product type: Magnetic flat gripper Brand: TECWERK Material: Hard ferrite Facts Diameter: 13 mm Height: 4.5 mm Holding force (max): 10 N Recommended operating temperature: up to 100 °C Maximum operating temperature (peak): 200 °C Packing unit: 10 Special features Design: Flat gripper without threaded sleeve Application: Holding / fixturing of ferrous parts Construction: Sintered ferrite magnet Usage: Suitable for compact fixtures and assembly jigs FAQ What is the maximum holding force of this magnetic flat gripper? The magnetic flat gripper offers a maximum holding force of 10 N, suitable for securing small ferrous components in fixtures and assembly stations. Which material is the magnet made from and what are the benefits? The unit is made from hard ferrite, providing good thermal stability and corrosion resistance for standard workshop environments. Can the gripper be used during heating operations? Short-term exposure is possible: recommended use is up to 100 °C with a peak tolerance of 200 °C for brief thermal steps. Is the product supplied with a threaded sleeve for fastening? This version is without threaded sleeve, offering a flush, low-profile contact surface for direct mounting or embedding. What is the packing quantity for ordering and which SKU applies? The item is supplied in a packing unit of 10 and is listed under SKU 4000832231NW (TECWERK). Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
16mm Magnetic Flat Gripper 18N Holding Force, Hartferrite, Without Threaded Bush - TECWERK
Take advantage of a compact, low-profile magnetic solution that combines a 16 mm diameter, 4.5 mm height and a reliable 18 N holding force for light-duty fixturing; supplied in practical packs of ten for straightforward stock handling — order or request availability via Metav Werkzeuge for fast delivery and technical guidance. Flat Magnetic Gripper D16 x H4.5 mm – 18 N holding force (TECWERK) A Flat Magnetic Gripper designed for light holding and fixturing in compact assemblies, supplied without a threaded bush for versatile surface integration Compact 16 mm diameter, 4.5 mm height Ceramic hard-ferrite magnetic material 18 N holding force for light-duty fixturing Temperature resistance up to 200 °C Space-saving design for tight fixtures and assemblies The small circular form factor with a 16 mm diameter and 4.5 mm height delivers a noticeably reduced footprint compared with bulkier magnets, enabling integration where space is limited. The slim profile simplifies placement into shallow recesses or narrow pockets on jigs and fixtures, while the flat face supports even contact with mating ferrous surfaces. This compact geometry reduces obstruction in automated handling systems and helps maintain clearances in dense assemblies, offering a practical solution for engineers and operators seeking efficient use of mounting area without compromising basic magnetic performance. Predictable holding performance and temperature resilience Manufactured from hard ferrite, the unit provides a stable magnetic field suitable for repeatable light holding tasks; the rated 18 N holding force offers a clear, measurable reference for design calculations and process planning. The component is specified with a recommended operating temperature up to 100 °C and a maximum of 200 °C, which allows selection for applications exposed to elevated temperatures that would impair many polymer-bonded magnets. Stating these limits helps maintenance planners and process engineers assess longevity under thermal load and avoid premature demagnetisation in high-heat processes. Integration flexibility and logistical convenience The delivery format as a pack of 10 supports predictable inventory control for workshops and production cells, reducing procurement frequency for frequently used small components. Supplied without a threaded bush, the part is intended for direct surface mounting or for combination with separate mounting hardware, offering flexibility for bespoke fixtures or adhesive attachment methods. Sourcing through a specialist supplier standardises quality and simplifies procurement—this is particularly valuable where consistent magnetic performance is required across multiple assembly lines or service kits. Request stock availability and tailored advice for the TECWERK flat magnetic gripper from Metav Werkzeuge — email info@metav-werkzeuge.com or call +49 2822 7131930 for product information and delivery options Technical data Article number: 4000832232NW Manufacturer: TECWERK Product type: Flat magnetic gripper Core technical data Diameter: 16 mm Height: 4.5 mm Holding force (max): 18 N Recommended operating temperature: up to 100 °C Maximum operating temperature: 200 °C Special features Material: hard ferrite Design: without threaded bush Packaging unit: 10 UID: 4000832232NW FAQ What is the typical use for this flat magnetic gripper? The TECWERK flat magnetic gripper (SKU 4000832232NW) is intended for light holding and fixturing tasks where a compact magnetic solution is required, such as small-part assembly, positioning aids and jigs. Can the magnet be used at elevated temperatures? Yes; the component is rated with a recommended operating temperature up to 100 °C and a maximum of 200 °C, allowing use in processes with moderate thermal exposure. How strong is the magnetic hold in practical terms? The nominal holding force is 18 N, providing a quantifiable basis for selecting the magnet for light-duty retention and positioning applications; real-world pull values depend on contact area and surface condition. What mounting options are available given the lack of a threaded bush? Since the unit is supplied without a threaded bush, it is suitable for direct surface mounting, adhesive bonding or incorporation into fixture plates where separate mounting hardware can be applied. Is the magnet material suitable for corrosive environments? The gripper is made from hard ferrite, a ceramic magnetic material with good stability; for corrosive or wet environments, consider additional surface protection or consult Metav Werkzeuge for compatible alternatives. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
16mm Magnetic Flat Gripper With Threaded Bushing, Holding Force 18N, M3 - TECWERK
Take advantage of a compact, high-temperature-capable magnetic clamping solution that combines a small footprint with dependable holding power; its hard ferrite construction and integrated M3 threaded socket facilitate quick assembly and reliable positioning. Order the magnetic flat gripper directly via Metav Werkzeuge or ask our consultants if needed. Magnetic flat gripper D.16 x H11.5 mm with M3 threaded socket – TECWERK The Magnetic flat gripper D.16 x H11.5 mm with threaded socket is a compact magnetic clamping element for secure holding of small ferrous parts in fixtures and assemblies. Compact diameter 16 mm design Integrated M3 threaded socket for easy fastening Hard ferrite magnetic core for stable magnetism Holding force 18 N and high-temperature rating Space-saving design that simplifies fixture layouts The compact 16 mm diameter and 11.5 mm height provide a small installation footprint while delivering practical clamping performance for light-duty applications. This reduced profile enables closer element spacing in jigs and fixtures, which helps to increase usable work area on assembly plates. The compact geometry also supports repeatable positioning where accurate local holding is required, reducing the need for larger, more intrusive clamping hardware. Predictable holding under heat for robust process control Constructed from hard ferrite, the component maintains magnetic properties across an extended temperature range, offering a recommended operating temperature up to 100 °C and a maximum of 200 °C. The rated holding force of 18 N gives a clear, measurable parameter for process planning, enabling engineers to calculate safety margins and fixture layouts with confidence. Explaining these figures in simple terms: the specified Newton value represents the axial pull the magnet can sustain on a flat steel contact, which is useful when assessing suitability for light-retention tasks. Quick integration with standard M3 mounting An integrated M3 threaded socket allows immediate mounting with common fasteners and adapters, shortening assembly time and simplifying retrofits into existing tooling. The thread interface provides a secure mechanical link so the magnetic element can be positioned and replaced without special tools. For designers this means fewer bespoke components and a faster route from prototype to production, supporting efficient maintenance cycles and lower downtime in routine operations. Contact Metav Werkzeuge for a specification check or order coordination — phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: 4000832242NW SKU: 4000832242NW Brand: TECWERK Facts Diameter: 16 mm Height: 11.5 mm Thread: M3 Holding force: 18 N Recommended operating temperature: up to 100 °C Maximum operating temperature: 200 °C Special features Material: hard ferrite Version: with threaded socket Product type: magnetic flat gripper Packaging unit: 10 FAQ What is the axial holding force of this magnetic element? The magnetic flat gripper provides a holding force of 18 N, which is the axial pull measured on a flat steel contact. Which thread is provided for mounting? Mounting is via an integrated M3 threaded socket, allowing direct fastening with standard M3 screws or adapters. What operating temperatures are possible with this gripper? The component has a recommended operating temperature up to 100 °C and can tolerate up to 200 °C for short periods or specialised applications. What material is the magnet made from and what does that mean for use? The core is made from hard ferrite, offering stable magnetic performance at elevated temperatures and suitability for general-purpose clamping of ferrous parts. How is the product typically used in fixtures? This compact magnetic element is used for light holding and positioning of small ferrous workpieces in jigs, assembly fixtures, and instrumentation where a low-profile clamp is required. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
20mm Flat Magnetic Gripper H6 Without Threaded Bush Holding Force 30N, Temp up to 200°C - TECWERK
Take advantage of a compact, high-temperature tolerant clamp with hard ferrite construction and a holding force of 30 N for reliable fixation of light components; order the magnetic flat gripper directly via Metav Werkzeuge or request advice from our consultants for application-specific guidance. Magnetic Flat Gripper Ø20 x H6 mm — TECWERK The Magnetic Flat Gripper Ø20 x H6 mm is a compact clamping magnet designed for secure, space-saving fixation of small parts in assembly, jigs and light-duty fixtures. Compact Ø20 x H6 design Hard ferrite magnet material Holding force 30 N for small parts Rated to 200 °C peak temperature Reliable holding for precise small-part clamping With a rated holding force 30 N, this compact flat magnet provides consistent adhesion for light components and small tools where repeated, secure contact is required. The low-profile Ø20 x H6 mm format minimises obstruction in tight assemblies and enables closer tolerances in fixturing. In practical terms, 30 N corresponds to a predictable retention suitable for aligning, holding and positioning operations; the numerical value supports rational selection when calculating safety margins and handling requirements. Durable construction with thermal resilience Manufactured from hard ferrite, the gripper retains stable magnetic properties and resists demagnetisation under normal workshop stresses. The component is specified with a recommended operating temperature up to 100 °C and a maximum of 200 °C, which indicates suitability for processes that involve elevated temperatures or intermittent heating. Hard ferrite also offers corrosion resistance and long-term magnetic stability, translating into lower replacement frequency and predictable performance over the product lifetime. Space-saving design for straightforward integration The version supplied without a threaded bush is optimised for flush mounting or incorporation into custom fixtures where a low profile is essential. Its simple geometry supports rapid layout and repeatable placement in modular tooling or vacuum tables, reducing overall system complexity. The ceramic magnetic core keeps maintenance needs minimal, while the compact footprint supports dense part arrays and micro-assembly tasks without significant redesign of existing tooling. For technical integration advice or to discuss supply options from Metav Werkzeuge, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 for prompt, specialist support. Technical data Article number: 4000832233NW Product type: Magnetic flat gripper Manufacturer: TECWERK Material: Hard ferrite Version: without threaded bush Dimensions & performance Diameter: 20 mm Height: 6 mm Holding force: 30 N Recommended operating temperature: up to 100 °C Maximum operating temperature: 200 °C Packaging unit: 10 Features & applications Compact flat clamping magnet Suitable for light-part fixation and positioning Ceramic hard ferrite magnet material Designed for direct flat mounting (no threaded bush) Low-profile solution for space-constrained fixtures FAQ What is the maximum holding capacity of this gripper? The gripper provides a holding force of 30 N as specified for the Magnetic Flat Gripper Ø20 x H6 mm (TECWERK, SKU 4000832233NW). Can this magnet be used at elevated temperatures? Yes, the unit is rated with a recommended operating temperature up to 100 °C and a maximum temperature tolerance of 200 °C. Is the gripper supplied with a threaded mounting option? This version is supplied without a threaded bush; it is intended for flat or bespoke mounting solutions. What material is the magnetic core made from? The core material is hard ferrite, selected for stable magnetic properties and resistance to demagnetisation. For which tasks is this flat magnet most suitable? The device is ideal for holding, aligning and light-fixture duties where a compact, low-profile magnetic clamp is required Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
20mm Flat Magnetic Gripper M3 Threaded Bush Holding Force 30N, Up to 200°C - TECWERK
Take advantage of compact, reliable magnetic holding with simple threaded mounting and temperature resilience; ideal for small fixtures and assembly jigs. Order TECWERK magnetic flat holders directly via Metav Werkzeuge or request technical advice from our consultants. TECWERK Magnetic flat holder D20 × H13 mm, M3 threaded bushing The magnetic flat holder D20×H13 mm is a compact magnetic fixing element designed for secure, space-saving attachment in light assembly and fixturing applications Compact magnetic holder, Ø20 mm, H13 mm Solid hard-ferrite magnet material Integrated M3 threaded bushing Holding force 30 N, high-temperature tolerant Reliable holding for light assembly and fixture tasks The magnetic flat holder delivers a consistent 30 N holding force, making it suitable for small part retention, positioning jigs and temporary fixtures where controlled magnetic adhesion is required. The specified holding force refers to the maximum axial pull under ideal contact conditions; in practice, surface finish and contact area influence the effective grip. The hard-ferrite composition ensures stable magnetic properties across a wide temperature range, providing dependable performance for repetitive assembly cycles without active maintenance. Space-saving mounting with threaded bushing for secure fixing With an outer diameter of Ø20 × H13 mm and an integrated M3 threaded bushing, this compact component enables straightforward mechanical fastening into fixtures, housings or tooling plates. The threaded insert permits simple screw attachment, reducing installation time and eliminating the need for additional adhesive bonding. The slim profile is particularly advantageous where clearance is limited, allowing magnetic fixing to be combined with precise mechanical alignment in tightly packed assemblies. Material selection and thermal behaviour for workshop environments Made from hard ferrite, the magnetic flat holder offers good magnetic stability and corrosion resistance typical of ceramic magnets, while remaining cost-effective for bulk use in workshops. The supplier guidance notes a recommended operating temperature up to 100 °C and a maximum of 200 °C, so the component is suitable for many industrial processes that involve raised temperatures, but should be kept away from direct heat sources exceeding the maximum rating. The brittle nature of ferrite ceramics should be considered during handling and assembly to avoid impacts that could cause chipping. For dependable small-part holding in workshop and light industrial applications, choose the TECWERK magnetic flat holder from Metav Werkzeuge — technical advice and local supply are available via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: 4000832243NW Product type: Magnetic flat holder Material: Hard ferrite Diameter: 20 mm Height: 13 mm Thread: M3 Execution: with threaded bushing Holding force: 30 N Recommended operating temperature: up to 100 °C Maximum operating temperature: 200 °C Packaging unit: 10 Facts Ø20 mm H13 mm M3 thread 30 N holding force Recommended up to 100 °C Maximum 200 °C Special features Integrated threaded bushing Compact flat design Hard-ferrite magnet material SKU 4000832243NW FAQ What holding force can be expected from this magnetic flat holder? The TECWERK magnetic flat holder provides a maximum holding force of 30 N; actual grip depends on contact surface and alignment. Can the holder be bolted directly into fixtures? Yes, the integrated M3 threaded bushing allows direct screw mounting into fixtures or tooling plates for secure attachment. Is the material suitable for elevated temperatures? The component, manufactured from hard ferrite, is recommended for use up to 100 °C and rated to a maximum of 200 °C under specific conditions. Are these holders suitable for heavy-duty magnetic clamping? This product is intended for light assembly and positioning tasks; for heavy-duty clamping, devices with higher rated holding forces should be selected. TECWERK: Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
25mm Flat Magnetic Holder With M4 Threaded Bush, 40N Holding Force, Up To 200°C - TECWERK
Combine compact dimensions with a reliable 40 N holding force and robust hard-ferrite construction for dependable, space-saving fixing in assemblies and jigs — order the magnet directly via Metav Werkzeuge or consult our advisors for application support. Flat magnetic holder D25×H15 mm with threaded bush — M4, 40 N, hard ferrite The flat magnetic holder D25×H15 mm is a compact magnetic mounting solution designed for secure, repeatable fixing in small fixtures, jigs and tooling applications. *Compact 25 mm diameter × 15 mm height *40 N holding force for small fixtures *Hard-ferrite magnet construction *Integrated M4 threaded bush for secure mounting Secure fixing in the smallest of spaces The compact 25 mm diameter and 15 mm height deliver a space-saving solution where conventional clamps cannot fit. Despite its small footprint, the component provides a holding force of 40 N, which is sufficient for light fixturing, positioning sensors and holding thin workpieces during assembly. The short profile reduces protrusion from the mounting surface and enables close packing of several magnetic holders for modular jigs. The robust hard-ferrite magnet material ensures stable magnetic performance and long service life in routine workshop use. Threaded fastening for precise alignment and repeatability An M4 threaded bush is integrated into the design so the holder can be mounted directly to fixtures, sensor brackets or tooling plates without additional adapters. The threaded interface supports repeatable alignment and straightforward replacement if a magnetic element needs changing. Installation is quick and reduces setup variability, which supports consistent process results and minimises downtime during tool changes or jig adjustments. Designed for workshop temperatures and short-term exposure The holder is specified with a recommended operating temperature of up to 100 °C and a maximum temperature tolerance of 200 °C, making it suitable for many production environments where elevated temperatures occur intermittently. This thermal resilience means the magnetic retention remains reliable during soldering near the fixture, heat-affected assembly steps or when used close to warm tooling, while prolonged exposure to the absolute maximum should be avoided to preserve magnetic strength. Practical uses and quick integration into existing tooling This flat magnetic component is ideal for applications such as temporary fixturing, locating small parts prior to fastening, or stabilising sensors and gauges during measurement. The low profile and threaded mounting make integration into custom fixtures straightforward, enabling flexible placement on jigs, machine guards or assembly benches. The compact magnet is a pragmatic choice where a discreet, reliable magnetic hold is required without heavy clamping equipment. For compact, reliable magnetic fixing contact Metav Werkzeuge for stock availability and tailored application advice — Metav Werkzeuge in Emmerich provides fast dispatch and expert consultancy via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 4000832244NW Label: Magnet flat holder D25×H15 mm with threaded bush Material: hard ferrite Execution: with threaded bush Diameter: 25 mm Height: 15 mm Thread: M4 Holding force: 40 N Recommended operating temperature: up to 100 °C Maximum operating temperature: 200 °C Packaging unit: 10 Facts Diameter: 25 mm Height: 15 mm Holding force: 40 N Thread: M4 Packaging unit: 10 Special features Hard-ferrite magnet material Integrated M4 threaded bush Compact flat profile for space-limited mounting Temperature tolerance up to 200 °C (short-term) Suitable for light fixturing and sensor mounting FAQ What holding capacity does the flat magnetic holder provide? The flat magnetic holder delivers a maximum holding force of 40 N, suitable for light fixturing and positioning tasks where a compact magnetic hold is required. How is the magnet mounted to a fixture? Mounting is via the integrated M4 threaded bush; the thread supports secure fastening and repeatable alignment when used in jigs or tooling plates. Which material is the magnet made from and what does that mean for longevity? The device uses hard-ferrite material, which offers stable magnetic performance and long service life for general workshop applications under normal conditions. What temperatures can the magnetic holder withstand? The holder has a recommended operating temperature up to 100 °C and a maximum short-term limit of 200 °C; prolonged exposure to the maximum should be avoided to preserve magnetic strength. Is the magnet suitable for heavy-duty clamping? This compact flat magnet is intended for light to medium fixturing tasks; applications requiring heavy clamping should use larger or higher-capacity magnetic systems. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
25mm Flat Magnetic Mount Without Threaded Bush 40N Holding Force, Max 200°C - TECWERK
Take advantage of the compact dimensions and reliable 40 N holding force for consistent part retention in production processes; the hard‑ferrite magnet offers temperature resilience up to 200 °C, while Metav Werkzeuge provides fast supply and specialist advice for seamless integration. TECWERK Magnetic flat holder D25 × H7 mm, 40 N holding force The TECWERK magnetic flat holder delivers a compact magnetic clamping solution for fixtures, jigs and small component handling in workshops and light industrial settings Compact D25 × H7 mm design Holding force 40 N Hard ferrite material Suitable up to 200 °C Accurate holding in a space‑saving format The hard ferrite construction provides a reliable magnetic field in a minimal footprint, making this component ideal where space is limited. With a diameter of 25 mm and a height of 7 mm, the unit achieves a holding force of 40 N, enabling secure retention of small parts during assembly or light machining. The compact dimensions reduce interference with neighbouring fixtures and help maintain clear access to workpieces, while the ferrite composition ensures wear‑resistant performance during repetitive use. Temperature resilience that supports process stability Designed for industrial environments, the magnet is specified with a recommended operating temperature of up to 100 °C and a maximum temperature of 200 °C, allowing use near heat‑generating processes. This thermal tolerance minimises loss of magnetic performance under warm conditions and supports consistent clamping force over cycles. For applications requiring heat exposure, the thermal data helps planners select suitable placement and cooling strategies to maintain operational integrity. Easy integration and dependable function without threaded bush Delivered without a threaded bush, the component simplifies direct bonding or press‑fit installation into fixtures and tooling plates, reducing design complexity for bespoke assemblies. The non‑threaded variant suits adhesive mounting or insertion into precision recesses and supports rapid retrofit into existing jigs. Backed by Metav's emphasis on traceable supply and quality control, the part contributes to predictable production outcomes and reduced rework rates. For ordering or technical consultation on the TECWERK magnetic flat holder, contact Metav Werkzeuge in Emmerich by e‑mail at info@metav-werkzeuge.com or by telephone on +49 2822 7131930 for prompt delivery and expert advice. Technical Data Article number: 4000832234NW Product type: Magnetic flat holder Diameter: 25 mm Height: 7 mm Material: Hard ferrite Design: without threaded bush Holding force: 40 N Recommended operating temperature: up to 100 °C Maximum temperature: 200 °C Packaging unit: 10 Facts SKU: 4000832234NW Manufacturer: TECWERK Product category: Magnetic clamping element Special features Compact form factor for tight fixtures Suitable for adhesives or press fit installation Ferrite magnet for stable magnetic properties Engineered for repetitive holding tasks FAQ What is the holding capacity of this magnetic flat holder? The TECWERK magnetic flat holder provides a holding force of 40 N, suitable for securing small components in jigs and light assembly operations. Which materials is the magnet made from and how does that affect use? The unit is manufactured from hard ferrite, which offers good magnetic stability and wear resistance; ferrite is particularly appropriate where corrosion resistance and cost efficiency are required. Can the magnet be used near heat sources? Yes. The device has a recommended operating temperature up to 100 °C and can withstand a maximum of 200 °C, making it suitable for many warm industrial environments with appropriate placement. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
32mm Magnetic Flat Gripper H7 No Threaded Bush Holding Force 80N - TECWERK
Take advantage of a compact design with reliable 80 N holding force and hard ferrite construction for steady, low-profile temporary fixing; order directly via Metav Werkzeuge or consult the Metav team for application advice. Flat magnetic gripper D32×H7 mm – 80 N, TECWERK The Flat magnetic gripper D32×H7 mm is a compact, ceramic magnet designed for secure temporary fastening and positioning in light-duty assembly, fixture and automation applications. *Compact 32 mm diameter for tight spaces Reliable 80 N maximum holding force Hard ferrite material for thermal stability Designed without threaded bush for flush mounting Consistent clamping with measurable holding force The flat magnetic gripper delivers a clear 80 N holding force, providing a predictable clamping action for small components and jigs. The specified holding capacity enables planners and engineers to calculate safety margins and define handling procedures with confidence. As a passive magnetic element, the component offers immediate magnetic attraction without additional actuation, which simplifies fixture design and reduces the number of moving parts required for temporary fastening. The compact footprint supports integration where space is constrained. Temperature-resistant, low-maintenance material choice Constructed from hard ferrite, this magnet affords good thermal resistance compared with many polymer-bonded alternatives. The product is rated with a recommended operating temperature up to 100 °C and a maximum of 200 °C, making it suitable for elevated-temperature assembly processes and short-term exposure to heat during production. Hard ferrite is a ceramic magnetic material that maintains magnetic characteristics at higher temperatures while remaining chemically stable; however, designers should consider the material's brittleness when specifying mechanical interfaces or impacts. Low-profile installation and straightforward integration With a 32 mm diameter and 7 mm overall height, the unit is engineered for flush mounting and minimal protrusion from fixture surfaces. The version supplied without a threaded bush reduces overall thickness and allows direct bonding, countersinking or clamping into shallow recesses in tooling plates. This low profile facilitates closer stacking of components and conserves valuable toolroom real estate. Integration into light-duty assembly rigs or positioning stations is therefore simpler and more space-efficient. For robust, space-saving magnetic holding in small-assembly tasks choose the TECWERK flat magnetic gripper and contact Metav Werkzeuge for bespoke advice and supply from Emmerich. Technical data Article number: 4000832235NW Product type: Flat magnetic gripper Brand: TECWERK Version: without threaded bush Facts Diameter: 32 mm Height: 7 mm Holding force max: 80 N Recommended operating temperature: up to 100 °C Maximum operating temperature: 200 °C Special features Material: hard ferrite Packaging unit: 10 Compact, low-profile design FAQ What holding capacity does the gripper provide? The TECWERK flat magnetic gripper provides a maximum holding force of 80 N, suitable for securing small parts and fixtures in light-duty applications. Is the magnet suitable for elevated temperatures? Yes. The unit is constructed from hard ferrite and is recommended for use up to 100 °C with a maximum permissible temperature of 200 °C for short exposures. How is the gripper mounted if it has no threaded bush? The version without a threaded bush is intended for flush mounting into shallow recesses, bonding or clamping within tooling plates to achieve a low-profile installation. What are the exact dimensions of the component? The gripper measures 32 mm in diameter with a height of 7 mm, providing a compact footprint for tight assembly spaces. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
32mm Magnetic Flat Gripper With Threaded Bush, Holding Force 80N, Up To 200°C - TECWERK
Take advantage of a compact, reliable magnetic hold combined with straightforward mounting and heat tolerance for efficient fixturing and short setup times; order directly via Metav Werkzeuge or contact our consultants for specification support. Magnetic flat gripper D32×H15 mm (M4) — 80 N holding force by TECWERK The magnetic flat gripper D32×H15 mm with an M4 threaded bush provides compact, non-powered holding for fixtures and small assemblies. Compact 32 mm diameter, 15 mm height Secure M4 threaded bush mounting 80 N holding force for stable fixturing Hard ferrite magnet for consistent performance Space-saving, high-hold fixturing for production The Magnetic flat gripper D32×H15 mm with M4 threaded bush and 80 N holding force is engineered for applications where a small footprint and reliable clamping are required. With a 32 mm diameter and 15 mm height, the unit occupies minimal space while delivering a rated 80 N of holding force — a practical balance between size and performance. The hard ferrite construction ensures magnetic stability under normal workshop conditions, while the compact form supports dense arrangements on assemblies and jigs. This makes the component suitable for repetitive assembly tasks, small-part fixturing and conveyor positioning where a consistent magnetic hold reduces repositioning and handling time. Fast, secure mounting and reduced setup time Mounting is simplified by the integral M4 threaded bush, which permits direct fastening into fixtures, plates or machine guards without additional adapters. The threaded insert secures the magnet mechanically, allowing rapid installation and minimal alignment effort in production setups. Because the gripper is non-powered, there is no need for wiring or pneumatic control, which shortens commissioning and lowers maintenance requirements. The combination of mechanical fixation and magnetic holding reduces the need for additional clamps, helping to streamline changeovers and increase throughput in workshops and small production runs. Temperature performance and workshop resilience The unit is specified with a recommended operating temperature of up to 100 °C and a maximum of 200 °C, offering resilience where elevated temperatures occur during processing or near heated tooling. The hard ferrite material provides stable magnetic properties across the stated temperature range; appropriate selection of the operating point will extend service life and maintain holding capacity. Supplied in a packaging unit: 10, the grippers are practical for batch replacement or equipping multiple stations. The robust, simple design supports routine industrial use while keeping handling and inventory straightforward. For dependable, compact magnetic fixturing choose the TECWERK magnetic flat gripper—contact Metav Werkzeuge for tailored advice and prompt dispatch from Emmerich. Technical data Article number: 4000832245NW Product type: Magnetic flat gripper Manufacturer: TECWERK Dimensions & core data Diameter: 32 mm Height: 15 mm Thread: M4 Holding force: 80 N Packaging unit: 10 Materials & operating conditions Material: Hard ferrite Version: with threaded bush Recommended operating temp: up to 100 °C Maximum operating temp: 200 °C FAQ What holding force does the gripper provide? The TECWERK magnetic flat gripper delivers a rated holding force of 80 N (SKU 4000832245NW), suitable for secure retention of small ferrous components. How is the gripper mounted? Mounting is via the integrated M4 threaded bush; the M4 thread allows direct fastening into fixtures or plates for a stable mechanical connection. Which materials can be held by the magnet? The device is intended for ferromagnetic workpieces such as steel; the magnetic flat gripper provides a reliable hold for typical ferrous assemblies and small components. Can the gripper be used near heated tooling? Yes. The gripper is specified with a recommended operating temperature up to 100 °C and a maximum of 200 °C; observe the recommended limit for prolonged performance. Is this product suitable for series production and workshop use? The compact design, standard M4 mounting and consistent magnetic performance make the unit appropriate for workshop applications, jigs and small-series production fixtures. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
40mm Flat Magnetic Gripper Without Threaded Bush Holding Force 125N, Temp Up To 200 °C - TECWERK
Take advantage of a compact, high‑force magnetic clamp that combines hard ferrite construction with a reliable 125 N holding force for small fixtures; order directly via Metav Werkzeuge or consult our specialists for integration advice. Magnetic flat gripper D.40xH8mm without threaded bush — compact hard ferrite clamp, 125 N holding force (TECWERK) Magnetic flat gripper D.40xH8mm without threaded bush for secure, space‑saving clamping in jigs, fixtures and light assembly applications Compact 40 mm diameter design Hard ferrite magnetic material 125 N holding force for secure clamping Withstands up to 200 °C peak temperature Precise clamping in a compact form for small assemblies The 40 mm diameter, low‑profile design delivers stable retention where space is limited. With a 125 N holding force, the component provides measurable clamping power while keeping bulk to a minimum. Built from hard ferrite, the unit is corrosion‑resistant for typical workshop conditions and designed for repeated placement in fixtures. The compact geometry supports accurate positioning and reduces the need for bulky clamps, which in turn can simplify jig design and save bench space. Consistent performance across normal operating temperatures Rated for a recommended operating temperature up to 100 °C and a maximum of 200 °C, the magnet is suitable for many light industrial environments where temperature exposure is intermittent. The temperature guidance helps predict changes in magnetic force over time and allows planners to choose an appropriate mounting strategy for processes involving heat. Clear temperature limits and material data enable a rational selection based on duty cycle rather than guesswork, supporting reliable process planning and fewer production interruptions. Flexible integration into fixtures thanks to a simple, threadless design The version supplied without a threaded bush offers a flush, unobstructed base that can be incorporated into bespoke fixtures or mounted in recessed pockets. The absence of a pre‑fitted thread simplifies customisation for specific applications and reduces the need to adapt standard fastenings. For bespoke assembly needs, secure bonding, countersinking or clamping arrangements can be chosen according to the fixture design; technical advice is available for selecting the most appropriate mounting method. Robust choice for repeated, low‑maintenance use Manufactured for dependable everyday use, the unit is engineered to deliver stable magnetic retention with minimal upkeep. The hard ferrite composition ensures long service life under standard workshop handling, while the clearly stated holding force gives planners a verifiable basis for fixture design. This combination of documented performance and simple mechanics makes the magnet an efficient choice for repetitive clamping tasks in production or repair settings. For compact, reliable magnetic clamping from TECWERK, contact Metav Werkzeuge for procurement support or tailored technical advice — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 4000832236NW SKU: 4000832236NW UID: 4000832236NW Dimensions / Performance Diameter: 40 mm Height: 8 mm Holding force: 125 N Recommended operating temperature: up to 100 °C Maximum temperature: 200 °C Packaging unit: 10 Materials / Design Material: hard ferrite Design: without threaded bush Product type: magnetic flat gripper Manufacturer brand: TECWERK FAQ What is the nominal holding force of this magnetic gripper? The magnetic flat gripper provides a holding force of 125 N, suitable for light clamping and fixturing tasks where this retention level is sufficient. Can the gripper be used at elevated temperatures? Yes, the unit has a recommended operating temperature of up to 100 °C and a maximum exposure rating of 200 °C for short periods. How is the gripper mounted without a threaded bush? The threadless base allows recessed or bonded mounting in custom fixtures; the design supports flush installation in jigs for a low overall profile. What material is the magnet made from and what are the benefits? Constructed from hard ferrite, the magnet offers stable magnetic properties, good corrosion resistance and suitability for routine workshop conditions. Is this product suitable for precision assembly jigs? Its compact 40 mm diameter and reliable holding force make it appropriate for many precision jigs where moderate retention and minimal bulk are needed. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
40mm Magnetic Flat Gripper With Threaded Bush Holding Force 125N, Up To 200°C - TECWERK
Take advantage of a compact, high-temperature-capable magnetic mounting with reliable 125 N holding force and a secure M5 threaded sleeve; order the flat magnetic holder directly via Metav Werkzeuge or consult our specialists for application advice. Flat magnetic holder D40×H18 mm by TECWERK — M5 thread sleeve, 125 N holding force Flat magnetic holder D40×H18 mm is a compact ferrite magnetic base designed for light clamping, positioning and fixturing tasks in workshops and assembly stations. 125 N holding force Hard ferrite construction M5 threaded sleeve Suitable to 200 °C short-term Reliable clamping where consistency matters The compact magnetic base delivers a measured 125 N of holding force, giving a dependable grip for small components and fixtures in routine workshop tasks. Constructed from hard ferrite, the unit maintains magnetic performance under regular industrial use and is specified with a recommended operating temperature up to 100 °C and a maximum of 200 °C for short-term exposure. These clear parameters support process planning and help avoid unexpected failures during thermal cycles. Space-saving design for flexible assembly With a diameter of 40 mm and a height of 18 mm, the magnetic holder fits into confined setups and can be mounted close to tooling or sensors without obstructing access. The integrated M5 thread sleeve permits secure fixing to threaded studs or adaptor plates, enabling repeatable positioning and quick replacement. This small footprint makes the component suitable for modular jigs, test rigs and light-duty fixturing where precision and accessibility are required. Durable choice that reduces handling time The ferrite magnet core and metal sleeve are engineered for straightforward, low-maintenance use: the magnetic base resists demagnetisation in normal workshop conditions and the threaded connection ensures stable mechanical coupling. As a result, assembly cycles benefit from fewer adjustments and reduced handling, supporting efficient throughput. The design emphasises functional reliability rather than decorative finish, making it a pragmatic option for production and repair environments. Contact Metav Werkzeuge for tailored procurement or application advice (info@metav-werkzeuge.com · +49 2822 7131930); our consultants will confirm compatibility and supply options quickly Technical data Article number: 4000832246NW SKU: 4000832246NW Manufacturer: TECWERK Product type: Flat magnetic holder Facts Diameter: 40 mm Height: 18 mm Holding force: 125 N Thread: M5 Recommended operating temperature: up to 100 °C Maximum operating temperature: 200 °C (short-term) Packing unit: 1 Special features Hard ferrite construction With threaded sleeve Compact design for tight spaces Suitable for light clamping and positioning FAQ What is the maximum holding force of the magnetic holder? The magnetic holder provides a maximum holding force of 125 N, suitable for light fixtures and component positioning. Which thread is integrated in the holder and how is it used? An M5 threaded sleeve is integrated into the unit, enabling secure attachment to threaded studs, adaptor plates or custom fixtures. What materials is the magnetic base made from? The core material is hard ferrite, combined with a metal threaded sleeve to ensure mechanical fixing and magnetic stability. What temperature ranges can the holder withstand? Normal operation is recommended up to 100 °C, with a maximum short-term exposure capability of 200 °C as specified. Is this magnetic holder suitable for heavy-duty machining fixturing? This product is intended for light clamping and positioning tasks; its 125 N holding force is optimised for small components rather than heavy machining loads. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com