M12×1 Thread Go Ring Gauge Metric ISO Fine Thread Right-Hand DIN 13, 6g, Hardened Gauge Steel - Metav IndustryLine

Take advantage of precise, standard‑compliant thread inspection and robust material selection to reduce rework and speed up quality checks; order the gauge directly via Metav Werkzeuge or consult their specialists for application advice.

Thread ring gauge M12 x 1 — Go gauge, DIN 13, 6g (Metav IndustryLine)

The Thread ring gauge M12 x 1 is a right‑hand go gauge for fast verification of metric ISO fine external threads to DIN 13 with tolerance 6g.

• Go gauge for M12 x 1 ISO fine thread
• Conforms to DIN 13, tolerance 6g
• Right‑hand thread checking
• Hardened gauge steel for long life

Ensure conformity with a single pass

This go gauge provides an immediate, binary check that external threads fall within the permitted maximum material limits defined by DIN 13. Used in production and incoming inspection, the device gives a clear pass result when the threaded part assembles without interference; parts that do not fit the gauge require rework or rejection. The concise inspection method reduces cycle time and simplifies operator training while maintaining measurable quality control.

Speed up throughput with reliable acceptance testing

Designed for routine use on the shop floor, the ring gauge converts dimensional criteria into a quick go/no‑go decision, avoiding time‑consuming measurements when the requirement is only conformity. The gauge is specified for metric ISO fine thread size M12 x 1, right‑hand, and the tolerance class 6g aligns with common production tolerances in mechanical engineering. This direct approach supports faster throughput and fewer stoppages on assembly lines.

Built for durability and repeatability

Manufactured from hardened gauge steel, the ring resists wear and preserves its geometry under repeated contact with external threads. The material choice prolongs service life and keeps inspection results reproducible over many cycles, reducing the need for frequent replacement. The compact, low‑mass construction (approx. 0.07 kg) facilitates handling and storage on a busy workshop bench while maintaining the stiffness necessary for reliable checking.

Traceability and stock identification made simple

Each unit is supplied with clear identification for inventory and traceability: SKU M315.112.4 and GTIN 4054469124018 allow straightforward ordering and record keeping. Compliance with the DIN 13 standard and the specified tolerance class 6g supports process documentation and audit trails, helping to demonstrate that thread acceptance criteria were consistently applied.

Contact Metav Werkzeuge to discuss supply of the M12 x 1 go gauge from Metav IndustryLine and to arrange prompt delivery from Emmerich.

Technical data

• SKU: M315.112.4
• GTIN: 4054469124018
• Weight: 0.07 kg
• Material: Gauge steel, hardened
• Designation: Thread ring gauge M12 x 1 mm go, DIN 13, metric ISO fine thread, right‑hand

Facts

• Size: M12 x 1
• Tolerance class: 6g
• Thread direction: Right‑hand
• eClass: 21170214
• Customs tariff number: 90173000

Special features

• Go (acceptance) ring gauge
• For metric ISO fine threads
• Complies with DIN 13
• Robust, hardened construction
• Category: Gauges / Ring gauges

FAQ

What does the go ring gauge check?
The go ring gauge verifies that an external thread fits within the maximum material condition specified for that thread; the Thread ring gauge M12 x 1 confirms whether a part meets the acceptance limit for an M12 x 1 metric ISO fine thread.

Is this suitable for left‑hand threads?
No, this particular item is a right‑hand gauge; for left‑hand threads a purpose‑made left‑hand ring gauge would be required rather than the M12 x 1 right‑hand version.

Which standard and tolerance does the gauge follow?
The gauge is manufactured to DIN 13 and inspects threads to tolerance class 6g, which corresponds to common production tolerances for metric ISO fine threads.

What material is used and how does that help?
Made from hardened gauge steel, the ring retains form under frequent use and offers extended service life compared with softer materials; the M12 x 1 ring remains accurate for many inspection cycles.

How is the gauge identified for stock and procurement?
The product is listed with SKU M315.112.4 and GTIN 4054469124018, enabling precise ordering and inventory control for the ring gauge.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com