M13 x 0.75 Three-Point Thread Go Ring, Right-Hand, Hardened Gauge Steel, DIN 13 6g - Metav IndustryLine

Reliable thread acceptance for fine-pitch assemblies is achieved through hardened gauge steel and DIN‑aligned tolerances; benefit from consistent Go verification and reduced rework. Order the thread ring gauge directly via Metav Werkzeuge or ask our consultants if needed.

Thread ring gauge M13 x 0.75 (Go) — ring gauge, DIN 13, 6g — Metav IndustryLine

Thread ring gauge M13 x 0.75 (Go) is a right‑hand ring gauge designed to verify conformity of metric ISO fine threads in production and incoming inspection.

• Go ring gauge for M13 x 0.75 metric fine thread
• Hardened gauge steel for lasting dimensional stability
• Conforms to DIN 13 tolerance class 6g
• Right‑hand thread verification for process control

Ensure correct fit for fine‑pitch assemblies

The Go ring gauge provides a fast, objective check that an M13 x 0.75 internal thread meets the specified form and size. By allowing only parts that pass the gauging plane, the gauge simplifies go/no‑go decisions at the inspection station and shortens cycle time for quality control. Constructed from hardened gauge steel, the tool resists wear and preserves a stable reference diameter, which supports repeatable acceptance testing and reduces scrap through reliable conformity checks.

Built to DIN standards for predictable tolerances

Compliance with DIN 13 and the 6g tolerance class means the gauge references an established interchangeability standard; this provides traceable limits that can be integrated into documented inspection plans. The nominal designation M13 x 0.75 identifies the thread diameter and pitch, while the right‑hand orientation matches common production threads. For manufacturers and inspection labs, this standardised approach enables consistent decisions across shifts and sites, improving throughput and minimizing measurement disputes.

Practical advantages in workshop and production use

The compact ring form factor facilitates rapid handling at control benches and assembly lines, so thread verification becomes a seamless step in the workflow rather than a bottleneck. The hardened gauge steel construction preserves calibration between checks; when combined with a clear part‑handling routine, the gauge helps maintain a stable quality baseline. Lightweight at 0.13 kg, the ring is easy to place and remove without compromising stiffness, delivering practical benefits where speed and accuracy matter most.

Traceability and identification for quality records

The ring is supplied with clear identification data (SKU and GTIN) suitable for process documentation and inventory control, supporting traceability across production batches. Using a dedicated ring gauge for M13 x 0.75 threads reduces ambiguity during audits and supports root‑cause analysis when nonconforming threads are found. Integrating the gauge into a documented inspection sequence helps demonstrate controlled measurement procedures and consistent application of the DIN 13 standard.

Specify the Metav IndustryLine thread ring gauge for reliable M13 x 0.75 verification — contact Metav Werkzeuge in Emmerich for delivery options and technical advice

Technical Data

• Article number: M315.113.3
• GTIN: 4054469124049
• SKU: M315.113.3
• Thread: M13 x 0.75
• Weight: 0.13 kg
• Orientation: Right‑hand

Facts

• Pitch: 0.75 mm
• Diameter class: M13
• Tolerance class: 6g
• Standard: DIN 13

Special features

• Go ring gauge for metric ISO fine threads
• Material: gauge steel, hardened
• Category: gauges / ring gauges
• Suitable for process and incoming inspection
• Compact, workshop‑friendly form

FAQ

What does the Go specification mean for this ring gauge?
The Go designation indicates the ring checks whether an internal thread meets the maximum material condition; the thread ring gauge M13 x 0.75 (Go) from Metav IndustryLine confirms acceptance when the part passes fully onto the gauge.

Can this gauge be used for both production and incoming inspection?
Yes. The Metav IndustryLine ring gauge is designed for routine checks in production and receiving inspection to ensure M13 x 0.75 threads conform to DIN 13, 6g.

How should the gauge be stored to preserve accuracy?
Store the ring gauge in a dry, dust‑free environment and protect it from impact; using a dedicated storage tray or labelled compartment helps maintain the hardened reference surface and ease traceability for SKU M315.113.3.

Does the ring gauge indicate if a thread is oversize or undersize?
The Go ring gauge confirms whether a thread meets the acceptance limit; if the part does not pass the gauge, it indicates the thread is outside the permitted size or form and requires further inspection.

Is the material resistant to wear during frequent use?
Yes. The gauge is manufactured from hardened gauge steel, which provides high resistance to abrasion and maintains dimensional stability under repeated gauging cycles.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com