M36x2 Thread Ring Gauge Metric ISO Fine Thread Right-Hand DIN 13 6g, Hardened Gauge Steel - Metav IndustryLine

The combination of hardened gauge steel, adherence to DIN 13 (6g) tolerances and a clear No‑Go function provides dependable rejection of out‑of‑tolerance threads; order the inspection ring directly via Metav Werkzeuge or consult our specialists for integration into production control.

No‑Go Thread Ring Gauge M36 x 2 mm — hardened gauge steel, DIN 13

The No‑Go Thread Ring Gauge M36 x 2 mm is a right‑hand inspection ring for quick verification of metric ISO fine threads in production and quality control.

• No‑Go gauge for clear rejection
• Hardened gauge steel construction
• DIN 13 tolerance class 6g
• M36 x 2 mm right‑hand thread

Ensure only conforming threads proceed on the line

The principal advantage of this inspection ring is consistent rejection: when a thread fails the No‑Go check, the part is immediately identified as non‑conforming, which reduces downstream rework and scrap rates. Built to verify metric ISO fine threads, the ring converts a subjective visual or tactile inspection into a binary, repeatable check. That rational clarity shortens decision times during routine checks and supports a faster, more efficient quality workflow.

Robust material for repeatable results

Manufactured from hardened gauge steel, the ring is dimensionally stable and resists wear under frequent use, which prolongs service life and maintains measurement certainty. The solid construction and designed contact geometry ensure repeatable engagement with the thread flanks; this repeatability is the technical basis for reliable pass/fail decisions on the shopfloor. The modest mass of the ring contributes to stable handling without unnecessary bulk during manual inspections.

Compliance with recognised standards and tight tolerances

Conformance to DIN 13 and the 6g tolerance class means the gauge matches established inspection criteria for metric threads, facilitating straightforward acceptance decisions in procurement and incoming inspection. Where documented evidence of inspection criteria is required, the specified standardisation simplifies communication between suppliers, production and quality management. Using standardised gauges accelerates audits and supports traceable quality routines.

Practical inspection use and workplace fit

Designed as a right‑hand inspection ring for M36 x 2 threads, the tool integrates into existing inspection benches and on‑process controls without complex training. The No‑Go function is especially useful where a rapid reject condition must be enforced to protect assembly steps downstream. Complementary handling practices — gentle cleaning after use and storage in a dry, protected spot — keep the gauge performing reliably over many cycles and maintain the integrity of the mating parts.

For a production‑ready thread control solution from Metav IndustryLine, request the No‑Go Thread Ring Gauge M36 x 2 mm through Metav Werkzeuge; technical advice and ordering assistance are available via info@metav-werkzeuge.com or by telephone on +49 2822 7131930

Technical data

• Article number: M315.236.7
• GTIN: 4054469126432
• Category: Gauges / Inspection rings
• Tariff number: 90173000

Core specifications

• Thread size: M36 x 2 mm
• Pitch: 2 mm
• Weight: 0.56 kg
• Tolerance class: 6g
• Thread direction: Right‑hand

Special features

• Material: hardened gauge steel
• Standard: DIN 13
• Function: No‑Go inspection ring (reject check)
• Intended use: Metric ISO fine threads

FAQ

What is the primary purpose of this gauge?
The No‑Go Thread Ring Gauge M36 x 2 mm is intended to provide a definitive No‑Go check for metric ISO fine threads, ensuring parts that exceed tolerance limits are rejected at inspection.

Which standard and tolerance does the ring conform to?
The inspection ring conforms to DIN 13 and the tolerance class 6g, matching common acceptance criteria for metric threads.

Is this ring suitable for left‑hand threads?
No, the gauge is manufactured for right‑hand threads only and will not correctly assess left‑hand thread forms.

What is the material and how durable is it?
Made from hardened gauge steel, the ring offers high abrasion resistance and dimensional stability for frequent use in quality routines.

Can the gauge be used directly in production control?
Yes; the gauge is designed for shopfloor inspection and can be incorporated into incoming inspection and in‑process checks to provide rapid pass/fail decisions.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com