M100x1.5 Thread Ring Gauge, Go/No-Go Metric ISO Fine Thread Right-Hand, Hardened Gauge Steel, DIN 13 6g, Calibrated Certificate - Metav IndustryLine

Take advantage of a hardened gauge-steel construction and DIN‑13, tolerance class 6g to secure repeatable thread inspection; delivered calibrated with a traceable calibration certificate for reliable quality control. Order directly via Metav Werkzeuge or consult our specialists for application advice.

No-go thread ring gauge M100 x 1.5 — right-hand, DIN 13 (6g) — Metav IndustryLine

The No-go thread ring gauge M100 x 1.5 is a right-hand metric ISO fine-thread inspection ring intended for pass/fail quality control in production and incoming inspection.

• Hardened gauge steel construction
• DIN 13 thread form, tolerance class 6g
• Supplied calibrated with certificate
• Right-hand no-go ring for M100 x 1.5

Precision where it prevents errors

The ring is manufactured from hardened gauge steel, giving dimensional stability and wear resistance that preserve the inspection limit over many cycles. Specified to DIN 13 and tolerance class 6g, the gauge provides a firm, objective criterion for thread acceptance: a correct part will pass the go check, whereas engagement with this no-go ring signals non-conformity. Delivered calibrated with a calibration certificate, traceability is established from the first inspection — a decisive benefit for manufacturers who must document conformity and reduce the risk of escapes.

Robust design for consistent pass/fail inspection

Built for routine use on the shop floor, the ring’s hardened material and precise thread form ensure reproducible checks with minimal maintenance. The no-go function is straightforward in practice: if the ring screws onto the part it indicates an oversize or incorrect thread form and the component is rejected, which speeds decision-making and reduces downstream rework. With a measured mass of 1.8 kg the gauge is solid in hand and designed to resist accidental distortion during handling, preserving measurement integrity across repeated checks.

Seamless fit into industrial quality workflows

Integration into existing inspection stations is uncomplicated thanks to the standard M100 x 1.5 sizing and compliance with established DIN standards, which supports interoperability across equipment and fixtures. Traceability is supported through the included calibration documentation, simplifying audit preparation and record keeping. Whether used at a receiving dock, in-line inspection point or final control, the ring serves as an efficient, cost-effective barrier against non-conforming threads while keeping throughput high and inspection steps clear.

For assured thread control with Metav IndustryLine’s hardened no-go ring, contact Metav Werkzeuge in Emmerich for expert advice and calibration documentation: +49 2822 7131930 or info@metav-werkzeuge.com

Technical data

• Article number: M315.800.6
• GTIN: 4054469152721
• Weight: 1.8 kg
• Material: hardened gauge steel
• Size: M100 x 1.5
• Type: No-go thread ring gauge
• Supplied with calibration certificate

Facts

• Diameter: M100
• Thread pitch: 1.5 mm
• Tolerance class: 6g
• Norm: DIN 13
• Tariff number: 90173000
• eClass: 21170214

Special features

• Right-hand thread orientation
• Complies with DIN 13 thread form
• Hardened gauge-steel construction
• Calibrated; includes calibration certificate for traceability
• Intended for pass/fail production inspection

FAQ

What does the no-go ring indicate during inspection?
The no-go ring indicates that a thread exceeds the permissible size or has an incorrect form; engagement with the ring marks the part as non-conforming for the No-go thread ring gauge M100 x 1.5.

Is the gauge supplied with calibration documentation?
Yes, the gauge is supplied calibrated and includes a calibration certificate to support traceability and quality records for the Metav IndustryLine ring.

Which standard does this thread gauge follow?
The ring follows DIN 13 with tolerance class 6g, providing compatibility with metric ISO fine-thread specifications used in production control.

Can this ring be used for left-hand threads?
No, this tool is manufactured as a right-hand thread ring; left-hand threads require the corresponding left-hand gauge.

What material is the ring made from and why does that matter?
The ring is made from hardened gauge steel, which ensures wear resistance and dimensional stability to maintain inspection accuracy over time.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com