M100x2 Thread Go Gauge For Metric ISO Fine Thread Right-Hand, Hardened Gauge Steel, DIN 13 6g With Calibration Certificate - Metav IndustryLine

Take advantage of the hardened gauge‑steel construction and factory calibration to secure reliable thread inspection in production; the DIN 13 (6g) tolerance and right‑hand M100 x 2.0 pitch provide unambiguous go/no‑go decision making. Order the thread ring gauge directly via Metav Werkzeuge or ask our consultants if needed.

Thread ring gauge M100 x 2.0 (No‑Go) — hardened gauge steel, DIN 13 (6g)

A Thread ring gauge M100 x 2.0 (No‑Go) intended for pass/fail inspection of metric ISO fine threads (right‑hand), designed for workshop and production quality control

• Hardened gauge steel construction
• Calibrated with certificate included
• Conforms to DIN 13, tolerance 6g
• Right‑hand metric fine pitch M100 x 2.0

Precise, standards‑based inspection for repeatable results

The core advantage lies in standardised, repeatable measurement: the hardened gauge steel body and the DIN 13 (6g) tolerance class make this a reliable instrument for thread assessment. As a no‑go inspection ring, it provides a clear fail criterion for oversize or out‑of‑tolerance threads, reducing subjective judgements on the shop floor. The supplied calibration certificate documents traceability and confirms the gauge was checked under controlled conditions — an important asset for internal quality procedures and audit trails.

Robust engineering for daily shop‑floor use

Constructed from hardened gauge steel, the ring resists wear and maintains form over repetitive checks, which preserves measurement integrity and limits the need for frequent replacement. The compact, solid design and a weight of approximately 1.8 kg ensure the ring is stable in handling yet portable between inspection stations. Robustness translates directly into lower process downtime: fewer instrument failures mean a steadier production flow and faster decision cycles during assembly or incoming inspection.

Integration into inspection workflows and traceability

The ring is intended for decisive go/no‑go verification rather than dimensional measurement, enabling rapid sorting of components during in‑process and final checks. Marking the instrument with clear identification (SKU and GTIN) and keeping the calibration certificate alongside batch records supports traceability and non‑conformity documentation. Using a dedicated no‑go ring for M100 x 2.0 pitch threads removes ambiguity from pass/fail calls and simplifies operator training for routine inspections.

Practical handling, storage and application advice

As a right‑hand metric fine‑pitch gauge, the ring is suited to checking mating threads produced to metric ISO fine standards. Handle the gauge with care: avoid forcing the ring onto threads and store it protected from contaminants and impact to maintain accuracy. When used as intended, the inspection ring speeds up quality gates and helps prevent assemblies with incorrect threads from entering later production stages — a small change that avoids costly rework and scrap.

Contact Metav Werkzeuge today to request the calibrated M100 x 2.0 no‑go thread ring gauge and benefit from reliable, standards‑based thread inspection supplied from Emmerich.

Technical Data

• Article number: M315.800.7
• GTIN: 4054469153766
• Weight: 1.8 kg
• Material: Gauge steel, hardened
• Designation: No‑Go thread ring gauge
• Thread size: M100 x 2.0
• Thread direction: Right‑hand
• Standard: DIN 13, 6g
• Calibration: Calibration certificate included

Facts

• Tolerance class: 6g
• Applicable standard: DIN 13
• Mass/size designation: M100 x 2.0
• Weight (approx.): 1.8 kg
• GTIN present: yes

Special features

• Intended use: Go/No‑Go inspection of metric ISO fine threads
• Construction: Hardened gauge steel for wear resistance
• Traceability: Supplied with calibration certificate
• Application area: Workshop and production quality control
• Category: Thread gauges / inspection rings

FAQ

What is the intended use of this thread ring gauge?
The thread ring gauge M100 x 2.0 (No‑Go) is intended for go/no‑go inspection of metric ISO fine threads to quickly identify oversize or out‑of‑tolerance threads.

Does the gauge come with calibration documentation?
Yes, the gauge is supplied with a calibration certificate confirming the inspection results and traceability.

Which tolerance and standard does the ring conform to?
The ring conforms to DIN 13 with tolerance class 6g, matching common specifications for metric ISO fine threads.

Can this gauge be used for left‑hand threads?
This specific item is manufactured for right‑hand threads; left‑hand thread checks require a correspondingly made ring.

How should the ring be stored to preserve accuracy?
Store the ring clean and protected from shocks and corrosive environments; keep the calibration certificate with the instrument to maintain traceability.

Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com