3.24mm Test Pin ±0.001mm Length 50mm Workshop Finish - Metav IndustryLine

Benefit from workshop-grade robustness, sub‑micrometre repeatability and a compact 50 mm length that fits confined gauges; order the test pin directly via Metav Werkzeuge or consult our specialists for tailored inspection advice.

Test pin M323.324 — Metav IndustryLine workshop test pin, 3.24 mm, ±0.001 mm

The Test pin M323.324 is a workshop‑grade gauging pin designed for end‑measure verification and plug‑gauge use in precision metrology environments.

• ±0.001 mm accuracy for high-precision checks
• 3.24 mm diameter in special steel
• 50 mm overall length for compact gauges
• Delivered in a protective transport case

Precision that secures measurement traceability

The design focuses on repeatable results in production and inspection. With a declared tolerance of ±0.001 mm, the pin delivers sub‑micrometre conformity consistent with high‑precision workshop checks; this level of accuracy supports confident go/no‑go evaluations and reduces rework cycles. The compact 3.24 mm gauge diameter and 50 mm overall length make the component suitable for confined sockets and small‑bore verifications where uncontrolled deformation would otherwise distort readings. Measured mass (approx. 6 g) and a short, rigid geometry minimise handling variance, so traceability chains remain robust and documentation of measurement results becomes more reliable.

Robust workshop design for dependable handling

Built as a workshop version, the pin is made from special steel chosen for dimensional stability and wear resistance under frequent contact conditions. The small mass and straightforward cylindrical form factor enable rapid insertion into gauge assemblies and jigs without complex fixturing. Delivery in a protective transport case preserves the calibrated condition during storage and transit, preventing scratches or contamination that would affect repeatability. The simple geometry also eases visual inspection for surface defects before use, contributing to predictable maintenance intervals and lower lifecycle costs.

Integration into efficient inspection workflows

The pin is suited for routine end‑measure controls, plug gauges and inline inspection stations where compact reference artefacts are required. Its nominal diameter and tight tolerance allow it to function as a reference element in master sets or as a dedicated check piece for specific bores. Because the component is deliberately straightforward to handle, cycle times for manual checks are reduced and throughput increases without sacrificing measurement confidence. For customers standardising inspection tooling, this workshop pin supports consistent test procedures and enhances the comparability of results across multiple operators and shifts.

For workshop traceability and reliable gauging results with the Metav IndustryLine range, request supply and technical advice from Metav Werkzeuge in Emmerich.

Technical data

• Article number: M323.324
• GTIN: 4061905058561
• SKU: M323.324

Facts

• Diameter: 3.24 mm
• Overall length: 50 mm
• Declared accuracy: ±0.001 mm
• Weight: 0.006 kg

Special features

• Material: special steel
• Workshop execution
• Supplied in a protective transport case

FAQ

What is the declared tolerance of the test pin?
The declared tolerance is ±0.001 mm for the Test pin M323.324, suitable for high‑precision workshop checks.

Which materials is the pin suitable for checking?
The pin itself is made from special steel and is intended as a reference artefact for gauging bores and end‑measure checks in metalworking inspection routines.

Is the pin supplied ready for use out of the box?
Yes, the Metav IndustryLine test pin is supplied protected in a transport case to preserve its condition until deployment.

Can this pin be used in plug‑gauge assemblies?
The compact 3.24 mm diameter and 50 mm length make the pin well suited for plug‑gauge and master set applications where a rigid reference is required.

How does the small mass affect handling and measurement stability?
The low mass (approx. 6 g) and short geometry reduce handling‑induced deflection, supporting more repeatable manual measurements with consistent contact behaviour.

Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com