3.42mm Test Pin Single, ±0.001mm Accuracy, Length 50mm, Workshop Version - Metav IndustryLine

Take advantage of workshop-ready precision of ±0.001 mm, a compact 3.42 mm diameter and a robust 50 mm length in special steel for reliable end‑measure checks; order the M323.342 gauge pin directly via Metav Werkzeuge or consult the Metav specialists for application advice.

M323.342 Gauge pin — 3.42 mm, ±0.001 mm (Metav IndustryLine)

The M323.342 gauge pin is a workshop‑grade precision test pin designed for fast end‑measurement verification and reference checks in metalworking and quality control environments.

• Workshop-grade precision pin
• Diameter 3.42 mm with ±0.001 mm tolerance
• 50 mm length in special steel
• Supplied in transport case for transit

Reliable accuracy for repeatable end‑measure checks

A compact test pin delivering ±0.001 mm tolerance provides a measurable improvement in inspection confidence and process control. The fine tolerance reduces the need for secondary checks and diminishes scrap rates by ensuring that end‑measure verifications are both fast and repeatable. Specified for a 3.42 mm diameter and a 50 mm working length, this probe form factor is well suited to tight clearances and compact assemblies where small variances have large downstream effects. The precision specification is suitable for demanding workshop checks that require micrometre‑level certainty.

Robust construction for continual workshop use

Manufactured from special steel, the component is engineered for wear resistance and dimensional stability in regular use. The workshop‑grade execution balances hardness for surface integrity with enough toughness to withstand routine handling. Supplied as a single test pin, the part’s compact mass and measured geometry ease insertion and removal during serial checks. For transport and protection, the pin is supplied in a protective case, helping to preserve the calibrated condition and preventing accidental damage during storage or transit.

Practical integration into inspection routines

The pin performs effectively in end‑measurement, reference and go/no‑go checks, serving as a simple but precise reference when rapid verification is required on the shop floor. Its compact size and tight tolerance shorten setup times and facilitate quicker decision cycles during first‑off inspections or routine sampling. The clearly defined physical parameters allow straightforward inventory control and identification in quality documentation, supporting efficient traceability within production logbooks and measurement reports.

Clear identification and workshop suitability

Designed for workshop use and labelled for easy identification, the gauge pin supports practical inventory and purchasing processes. The small mass and standard geometry mean the pin integrates with common holding fixtures and inspection benches without extensive adaptation. Where compact, high‑precision end measurements are needed, this test pin offers a direct, low‑complexity solution that aligns with typical metalworking and QA workflows.

For workshop procurement and expert advice on integrating the Metav IndustryLine M323.342 gauge pin into existing inspection routines, contact Metav Werkzeuge in Emmerich for prompt, locality‑based assistance.

Technical data

• SKU: M323.342
• GTIN: 4061905058103
• Article: Gauge pin, diameter 3.42 mm
• Material: Special steel

Facts

• Diameter: 3.42 mm
• Length: 50 mm
• Tolerance: ±0.001 mm
• Weight: 0.006 kg

Special features

• Workshop execution
• Supplied in a transport case for protection
• Single test pin for end‑measure verification
• Suited to reference and go/no‑go checks

FAQ

What tolerance does the pin offer?
The M323.342 gauge pin provides a tolerance of ±0.001 mm, making it suitable for micrometre‑level end‑measurement checks in workshop environments.

What material is used for the gauge pin?
This Metav IndustryLine test pin is made from special steel, selected for wear resistance and dimensional stability under normal workshop use.

Is the pin delivered protected for transport?
Yes. The gauge pin is supplied in a protective transport case to preserve the measuring surface and to reduce the risk of damage during handling.

Which applications are appropriate for this test pin?
The pin is intended for end‑measure verification, reference checks and simple go/no‑go tasks in metalworking, quality control and inspection workflows.

How can the product be identified for ordering and stock control?
Use the SKU M323.342 and GTIN 4061905058103 to identify the Metav IndustryLine gauge pin within procurement and inventory systems.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com