4.19mm Gauge Pin Single ±0.001mm Length 50mm Workshop Version - Metav IndustryLine

Combine 4.19 mm nominal diameter with an ultra‑tight ±0.001 mm tolerance and workshop‑grade construction to achieve repeatable go/no‑go checks and reduced rework. The pin’s 50 mm length and robust material offer reliable reference geometry for fixture set‑up and dimensional verification; order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed.

Gauge pin M323.419 – 4.19 mm Ø, ±0.001 mm tolerance, 50 mm length (Metav IndustryLine)

The gauge pin M323.419 is a workshop‑grade precision cylinder intended for end‑measure checks, fit verification and fixture setting in routine inspection environments

• Workshop version for routine inspection
• Diameter 4.19 mm with ±0.001 mm tolerance
• 50 mm overall length for through‑tests
• Made from special steel for wear resistance

High precision that stabilises measurement results

The gauge pin is designed to deliver a ±0.001 mm tolerance, a level of conformity that supports critical fit and clearance checks where small deviations matter. This degree of accuracy reduces uncertainty in pass/fail decisions and limits scrap caused by ambiguous fits. The nominal 4.19 mm diameter serves as a repeatable master for bore checks, pin gauges and assembly trials; because the tolerance is specified in micrometres, inspectors gain a concrete, comparable datum that integrates directly into quality control plans and inspection protocols.

Robust workshop design for everyday use

Constructed in special steel, the pin is tailored to withstand frequent handling and the mechanical demands of a production environment. The 50 mm overall length gives sufficient engagement for through‑tests while remaining easy to manoeuvre by hand; at approximately 0.007 kg the component is light enough for rapid interchange. Delivery in a transport case (plastic or wooden variant for protection during transit) keeps the reference geometry safe between uses. The workshop configuration prioritises durability and straightforward maintenance so that reference standards remain stable across multiple shifts.

Practical integration into inspection and fixturing workflows

As a dimensional master, the pin functions both as a direct inspection artefact and as a reference for setting gauges and jigs. Its cylindrical form suits alignment checks, ring gauge comparisons and quick fit verification in assembly processes. Traceability is supported by clear identification (SKU M323.419, GTIN 4061905056680) that eases stock control and documentation. The combination of tight tolerance and robust material translates into measurable efficiency gains: fewer repeat measurements, faster set‑up times and more consistent quality outcomes across batches.

For workshop‑grade accuracy and consistent fit verification, contact Metav Werkzeuge in Emmerich (info@metav-werkzeuge.com / +49 2822 7131930) to confirm availability and delivery

Technical data

• SKU: M323.419
• GTIN: 4061905056680
• Category: Gauge pins (Messstifte)
• Manufacturer: Metav IndustryLine

Facts

• Diameter: 4.19 mm
• Tolerance: ±0.001 mm
• Length: 50 mm
• Weight: 0.007 kg
• ECLASS: 21170231

Special features

• Workshop version for routine inspection
• Material: special steel
• Delivered in a transport case for protection during transit
• Intended for end‑measure checks, fit verification and fixture set‑up

FAQ

What tolerance does this gauge pin offer?
The gauge pin M323.419 is specified to ±0.001 mm, which provides tight dimensional control for fit and clearance checks.

Is the pin supplied ready for workshop use?
Yes, the M323.419 is a workshop‑grade pin supplied in a protective transport case to preserve the reference geometry during handling and transit.

What is the intended application for this pin?
The pin is intended for end‑measure checks, setting jigs and fixtures, bore verification and quick fit tests where a stable reference diameter is required.

Does the delivery include a calibration certificate?
No specific calibration certificate is included by default for the M323.419; any calibrated delivery will be stated explicitly in the product labelling or documentation.

Can this pin be used as a master for setting gauges and fixtures?
Yes, the dimensional stability and tight tolerance make the pin suitable as a master reference for setting gauges, aligning fixtures and validating bore fits

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com