4.32mm Gauge Pin Single, ±0.001mm Accuracy, Length 50mm, Workshop Version - Metav IndustryLine

A compact inspection solution that pairs extreme geometric fidelity with workshop durability: the combination of a 4.32 mm nominal diameter, a ±0.001 mm tolerance and a 50 mm length delivers reproducible end‑measurements and simple integration into inspection fixtures. Order directly via Metav Werkzeuge or consult our specialists for application advice.

Gauge pin M323.432 (single) – 4.32 mm, ±0.001 mm, 50 mm by Metav IndustryLine

The gauge pin M323.432 is a single precision test pin designed for accurate end‑measurements and go/no‑go checks in workshop inspection and fixture alignment.

• Diameter 4.32 mm with ±0.001 mm tolerance
• 50 mm overall length for end measurements
• Made from special steel for wear resistance
• Workshop version for robust everyday use

Precision where end measurements count

A precision pin with a 4.32 mm nominal diameter and ±0.001 mm runout tolerance provides a reliable reference for end‑measurements and alignment tasks. The tight tolerance reduces measurement uncertainty during comparative gauging, enabling faster decision cycles on production lines and in inspection benches. Built from special steel, the pin maintains geometric stability under repeated seating and withdrawal, so inspection procedures remain consistent over many cycles. The compact geometry and standard length make the pin suitable for use as a stop, register or probe in fixtures and jigs where a defined end‑dimension is required.

Designed for workshop environments and repeatability

This workshop‑grade test pin combines hardened material properties with a finish geared toward repeatable seating and low wear. The 50 mm length ensures accessibility in confined assemblies while providing sufficient register for secure fixturing. Where speed and reproducibility are priorities, the pin’s specification shortens setup times and reduces the need for frequent rework: a precise reference part simplifies go/no‑go checks and complements optical or mechanical comparators. The robust construction is intended to withstand the routine handling typical of maintenance and production environments without sacrificing the submicrometre stability implied by its tolerance class.

Practical handling, traceability and integration

Lightweight at approximately 0.008 kg and supplied as a single test element, the pin is easy to incorporate into existing inspection arrays or handheld gauging procedures. The geometry and finish are compatible with common clamping and holding systems, so retrofitting to a probe block or an indexing plate is straightforward. Traceability details such as article identifiers and the manufacturer’s SKU are provided for inventory and quality records, supporting batch control and replacement planning. Where certified traceability is required for internal QA, Metav Werkzeuge can advise on calibration and documentation options to match shop standards.

Choose the Metav IndustryLine gauge pin for dependable end‑measurement accuracy and contact Metav Werkzeuge in Emmerich for tailored advice and reliable supply.

Technical data

• Article number: M323.432
• GTIN: 4061905058592
• SKU: M323.432

Facts

• Diameter: 4.32 mm
• Length: 50 mm
• Tolerance: ±0.001 mm
• Weight: 0.008 kg

Special features

• Material: special steel
• Single gauge pin for end measurements
• Workshop execution for everyday use

FAQ

What accuracy can be expected from this test pin? The gauge pin M323.432 is specified at ±0.001 mm, which makes it suitable for demanding workshop checks and fine alignment tasks.

Is the pin suitable for fixture and jig use? Yes. The 50 mm length and hardened special‑steel construction make the pin well suited for integration into fixtures, jigs and register points.

Can this pin be used for go/no‑go gauging? The geometry and tolerance class of the M323.432 allow it to serve as a reference element in go/no‑go assemblies and manual inspection routines.

What information is available for stock and traceability? The product is supplied with the article number and GTIN for inventory systems; use the SKU M323.432 for reordering and record‑keeping.

Which materials is the pin intended to contact? The pin is manufactured from special steel and designed for general workshop contact with typical ferrous and non‑ferrous components; for specialised material interactions, consult Metav Werkzeuge.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com