4.33mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version, Special Steel - Metav IndustryLine

Take advantage of a workshop-ready measuring solution that combines ultra-fine ±0.001 mm tolerance, a precise 4.33 mm diameter and a compact 50 mm length for repeatable end‑measure checks and fixture set‑up. Order the gauge pin directly via Metav Werkzeuge or contact our consultants for application advice.

Gauge pin M323.433 — 4.33 mm, ±0.001 mm tolerance (Metav IndustryLine)

The gauge pin M323.433 is a single precision test pin for end‑measure verification and alignment tasks in workshop and inspection environments

• Workshop version for robust daily use
• Diameter 4.33 mm with ±0.001 mm accuracy
• Length 50 mm, special steel construction
• Single gauge pin for end‑measure checks

Reliable fit and measurable repeatability for inspection tasks

The gauge pin delivers consistent, measurable fits thanks to a diameter of 4.33 mm held to a tight ±0.001 mm tolerance. Such precision supports repeatable end‑measure checks and helps to verify bore sizes, plug fits and alignment points without ambiguity. As a result, setup times can be shortened and quality decisions become straightforward because the dimensional condition is expressed in clear numerical terms rather than impression or feel. The exact tolerance level translates directly into traceable, reproducible outcomes on the workshop floor.

Robust material and compact form for daily use

Manufactured from special steel, the pin combines surface stability with resistance to routine handling. At 50 mm overall length the component is compact yet long enough to stabilise in fixturing and alignment procedures while remaining easy to manipulate. The workshop version designation indicates a build focused on durability and practical use: edges and seating surfaces are suited for frequent insertion and removal, and the compact mass reduces the risk of accidental bending in common handling scenarios. Weight and dimensions make it convenient to incorporate into gauge sets and inspection trays.

Integration into quality routines and inventory logic

The single test pin is ideal as a reference element for incoming inspection, process control and final checks. Where end‑measure verification is required, the pin acts as an objective physical standard that removes subjective judgement from go/no‑go decisions. Its small footprint supports easy storage with other precision tools and enables fast substitution in modular fixture systems. For procurement and inventory control the clear identification of diameter, tolerance and length ensures unambiguous replacement and compatibility with existing gaging processes.

For workshop-grade repeatability and tailored advice on using the M323.433 gauge pin, contact Metav Werkzeuge for application support and ordering.

Technical Data

• Article number: M323.433
• GTIN: 4061905058608
• Material: Special steel
• Diameter: 4.33 mm
• Length: 50 mm
• Tolerance: ±0.001 mm
• Weight: 0.008 kg

Facts

• Measurement diameter: 4.33 mm
• Nominal length: 50 mm
• Dimensional tolerance: ±0.001 mm
• Mass: 0.008 kg

Special features

• Workshop version
• Single gauge/test pin
• Intended for end‑measure checks and alignment
• Compact, easy to handle

FAQ

What is the intended use of this gauge pin?
The gauge pin M323.433 is intended for end‑measure verification, plug‑fit checking and alignment tasks in workshop and inspection setups.

Which materials is the pin suited to check or verify?
The pin is a dimensional reference and may be used to verify bores and fits in components made from typical engineering materials; the M323.433 itself is supplied in special steel for stability and wear resistance.

How precise is the pin and what does that mean in practice?
With a tolerance of ±0.001 mm, the pin provides a high level of repeatability suitable for precise inspection tasks where minimal clearance variation is required.

Is this product suitable for routine workshop handling?
Yes—the workshop version construction of the M323.433 is designed for frequent use and straightforward integration into inspection routines.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com