4.73mm Gauge Pin Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine

Take advantage of the combination of ultra‑fine accuracy and workshop robustness for dependable end‑dimension verification; the M323.473 gauge pin with a diameter of 4.73 mm, a tolerance of ±0.001 mm and a length of 50 mm delivers repeatable results and easy handling — order via Metav Werkzeuge or contact the consultants for specification support.

M323.473 — Gauge pin (Test pin), Ø 4.73 mm, ±0.001 mm, Length 50 mm (Metav IndustryLine)

the M323.473 gauge pin is a workshop‑grade measuring pin for rapid verification of end dimensions and bore checks in production and inspection environments

• Extreme accuracy ±0.001 mm
• Diameter 4.73 mm
• Length 50 mm
• Workshop‑grade special steel

Dependable accuracy for end‑dimension control

The primary advantage of this measuring pin is its exceptional tolerance of ±0.001 mm, which makes it suitable for critical end‑dimension checks and reference measurements where small deviations matter. With a nominal diameter of 4.73 mm, the pin functions as a precise plug for bore verification and fit testing; the fine tolerance reduces uncertainty in pass/fail decisions and supports tighter process control. Explaining the figure: ±0.001 mm represents a sub‑micrometre acceptance window, enabling the substitution of manual gauging procedures with a compact, repeatable reference that shortens inspection time and improves throughput.

Robust workshop design that simplifies handling

Manufactured in special steel and presented in a workshop execution, the pin combines mechanical durability with manageable ergonomics. At a length of 50 mm the pin is long enough for stable engagement in many bores and short enough to avoid undue leverage‑induced bending, while its low mass promotes easy positioning during rapid checks. The solid construction is tuned for repetitive use in production environments, minimising wear on contact faces and maintaining the specified tolerance over many cycles. Where handling speed and resilience are priorities, this compact measuring element offers a low‑effort, high‑precision solution.

Identification, traceability and practical integration

The gauge pin is prepared for direct integration into inspection routines and fixtures: clearly identified by SKU M323.473 and GTIN 4061905060847, it serves as a repeatable reference for end‑dimension documentation and incoming inspection. The simple geometry eases storage and nesting in holder systems, while the workshop format supports frequent use on the shop floor. For procurement and planning, Metav IndustryLine supplies this component as part of a broader metrology range, supporting consistent quality across batches and enabling easy replacement without requalification of measuring procedures.

Contact Metav Werkzeuge for technical advice and to arrange supply of the Metav IndustryLine gauge pin directly from Emmerich — phone +49 2822 7131930 or eMail info@metav-werkzeuge.com

Technical data

• Article number: M323.473
• GTIN: 4061905060847
• Manufacturer: Metav IndustryLine

Facts

• Diameter: 4.73 mm
• Tolerance / Accuracy: ±0.001 mm
• Length: 50 mm
• Weight: 0.009 kg

Special features

• Material: special steel
• Workshop execution
• Intended use: end‑dimension verification / bore checks
• Packaged for transport in a protective case

FAQ

What level of accuracy can be expected from this gauge pin?
The M323.473 gauge pin is specified with an accuracy of ±0.001 mm, making it suitable for high‑precision end‑dimension and fit checks on small bores.

Is the pin suitable for repeated use in a production environment?
Yes, the workshop‑grade construction in special steel is designed for frequent handling and repetitive inspections typical of manufacturing workflows.

Can this pin be used as a reference for go/no‑go testing?
The nominal diameter of 4.73 mm and the tight tolerance allow the pin to act as a repeatable reference in go/no‑go assessments and pass/fail fixtures.

How is the M323.473 identified for inventory and traceability?
The component is supplied with SKU M323.473 and GTIN 4061905060847 for clear identification and traceability within inspection protocols.

What packaging is used for transport and storage?
The pin is supplied in a protective transport case to prevent damage during handling and transit, simplifying storage on the shop floor.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com