5.05mm Test Pin, Single, ±0.001mm Accuracy, Length 50mm, Workshop Finish - Metav IndustryLine

Taking advantage of the combination of workshop‑grade robustness, ±0.001 mm accuracy and a compact 50 mm length ensures reliable end‑measure checks in daily inspection routines — order this precision gauge pin directly via Metav Werkzeuge or consult our specialists for application advice.

Gauge pin, single — 5.05 mm, ±0.001 mm, 50 mm length (Metav IndustryLine)

The gauge pin, single, 5.05 mm ±0.001 mm, 50 mm length is a compact, workshop‑grade reference pin for precise end‑measure and fit checks in inspection and fixture set‑up.

• Workshop version for robust use
• High tolerance: ±0.001 mm
• Diameter 5.05 mm, length 50 mm
• Delivered in transport case

Reliable measurement where tight tolerances decide

A compact gauge pin with a declared tolerance of ±0.001 mm provides a clear technical advantage where repeatable go/no‑go decisions are required. The extremely fine tolerance corresponds to high‑precision gauges used for end measurements and fits; in practice this reduces rework and speeds up pass/fail decisions on the shop floor. The stated accuracy should be interpreted as the manufacturing tolerance of the pin, ensuring it can serve as a stable reference for short‑range checks and comparative measurements. When paired with calibrated ring gauges or micrometres, the pin acts as a simple, direct measure for bore and hole verification.

Durable design tailored to workshop routines

Constructed from special steel, this workshop version is intended for regular handling and quick inspection cycles. The material choice balances hardness and wear resistance, so the gauge retains form over repeated seating and insertion operations. With a 50 mm overall length and a 5.05 mm diameter, the component is compact enough for bench use yet long enough to reach into slightly recessed features. Supplied in a transport case, the pin remains protected during storage and transit, reducing the risk of dings that would compromise measurement integrity. The modest mass contributes to easy handling during serial checks without introducing operator fatigue.

Simple integration into quality control workflows

As a single reference pin for end‑measure tasks, this item integrates directly into existing inspection routines and fixture checks. The product supports quick tactile verification and comparative gauging; technicians can use it to check bore fits, set gauges, or verify plug clearances. Describing the part as a precision reference helps planners decide its role: whether as a temporary go/no‑go aid, a setup reference in jigs, or a control artefact for routine dimensional checks. The compact format and workshop specification make it particularly suitable where a reliable, ruggedised pin is needed rather than delicate laboratory artefacts.

For workshop‑grade inspection with ±0.001 mm tolerance, contact Metav Werkzeuge for purchasing and technical advice at info@metav-werkzeuge.com or +49 2822 7131930

Technical data

• Article number: M323.505
• GTIN: 4061905057045
• Label: Prüfstift, einzeln, 5,05mm, +/- 0.001 mm Länge 50 mm

Facts

• Diameter: 5.05 mm
• Length: 50 mm
• Tolerance / accuracy: ±0.001 mm
• Weight: 0.011 kg

Special features

• Material: special steel
• Workshop version
• Supplied in a transport case

FAQ

What is the intended use for this gauge pin?
The gauge pin (single, 5.05 mm, ±0.001 mm, 50 mm length) is intended for end‑measure checks, bore verification and fixture set‑up in workshop inspection routines.

Is the gauge pin suitable for regular shop‑floor use?
Yes, the workshop version and special steel construction make this pin suitable for frequent handling and routine measurements on the shop floor.

How is the gauge pin protected during storage and transport?
The item is supplied in a transport case to protect the precision surface from damage during storage and transit.

Can this pin be used as a reference for calibration chains?
The pin serves as a stable reference for comparative checks and can be part of a calibration chain when used alongside calibrated ring gauges or micrometres.

What product identifiers should be quoted when ordering?
Please quote SKU M323.505 and GTIN 4061905057045 when enquiring or ordering this gauge pin.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com