5.93mm Gauge Pin Length 50mm ±0.001mm Workshop Finish - Metav IndustryLine

Precise component checks benefit from the combination of a tight ±0.001 mm tolerance, a 5.93 mm diameter and a practical 50 mm length; the special-steel construction and workshop execution ensure reliable everyday use. Order the pin gauge directly via Metav Werkzeuge or ask our consultants if needed.

Pin gauge, single, 5.93 mm — workshop pin gauge with ±0.001 mm tolerance and 50 mm length (Metav IndustryLine)

Pin gauge, single, 5.93 mm is a compact inspection pin designed for high-precision dimensional checks and go/no-go verification in workshop and shop-floor environments.

• Workshop-ready precision ±0.001 mm tolerance
• Diameter 5.93 mm for tight-fit checks
• 50 mm length suitable for deep measurements
• Special-steel construction for durability

Accuracy for functional verification and quality control

A diameter of 5.93 mm combined with a tolerance of ±0.001 mm delivers the dimensional certainty required for functional fits and final inspection tasks. This level of accuracy reduces ambiguous pass/fail decisions when checking mating bores or precise housings; the narrow tolerance converts measurement data into actionable quality-control outcomes. The compact format and repeatable geometry make the gauge ideal for production sampling and incoming‑goods verification, where quick, reliable validation prevents downstream rework and saves processing time.

Built for workshop routines and daily handling

The workshop execution and special steel construction provide abrasion resistance and sustained dimensional stability under frequent use. At a nominal mass the pin minimises inertial effects during insertion and removal, helping keep measurements consistent across many cycles. Supplied in a protective plastic or wooden case for transport, the single-piece gauge is protected between uses to limit surface damage and preserve the critical diameter. The robust finish and handling-friendly length ensure compatibility with standard inspection benches and portable test setups.

Practical integration into measurement workflows

Designed as a straightforward verification tool, the inspection pin speeds up go/no-go checks and complements more complex measuring systems without adding process complexity. The compact form factor fits jigs, fixtures and V‑blocks, while the short overall length reduces the risk of bending when used manually. As a dedicated gauge pin, it supports rapid decisions during assembly, final inspection or tool set‑up, improving throughput and reducing scrap through prompt detection of out-of-tolerance conditions.

Dependable supply and workshop confidence

The single-piece format simplifies traceability and record keeping for routine checks. Metav IndustryLine builds on workshop-focused design principles to offer instruments that are practical, durable and easy to store. The pin’s combination of a tight tolerance, stable material and protective transport case means less downtime for replacements and fewer interruptions to production — a pragmatic choice for workshops aiming for consistent quality without overcomplicating inspection procedures.

For workshop-ready, high-precision checks request technical advice or supply information from Metav Werkzeuge — fast delivery from Emmerich and expert consultation available

Technical data

• Article number: M323.593
• GTIN: 4061905061431
• Label: Pin gauge, single, 5.93 mm, ±0.001 mm, length 50 mm
• Material: Special steel

Facts

• Diameter: 5.93 mm
• Length: 50 mm
• Tolerance: ±0.001 mm
• Weight: 0.013 kg

Special features

• Workshop execution
• Delivered in plastic or wooden case for transport
• Single-piece gauge for end-measure checks
• Compact, low-mass pin for minimal insertion disturbance

FAQ

What level of accuracy does this pin provide?
The pin gauge offers a ±0.001 mm tolerance, allowing the Pin gauge, single, 5.93 mm to be used for precision fit checks and final inspection tasks where tight dimensional control is required.

Is the gauge suitable for repeated shop-floor use?
Yes, the Metav IndustryLine inspection pin is a workshop execution made from special steel, designed to withstand frequent handling while maintaining its critical diameter.

Does the product come protected for transport?
The single-piece gauge is supplied in a protective plastic or wooden case for transport to preserve the surface and ensure continued accuracy during transfer and storage.

Can this pin be used for bore verification and go/no‑go checks?
The compact format and tight tolerance make this inspection pin well suited to bore verification, mating-fit assessments and quick go/no‑go decisions on the shop floor.

Is the gauge appropriate for integration into jigs or fixtures?
Its 50 mm length and low mass allow straightforward use in jigs, holders and portable inspection arrangements without introducing significant bending or handling error.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com