6.11mm Test Pin Single ±0.001mm Length 50mm, Workshop Version - Metav IndustryLine

High-precision reference for end measurements: a gauge pin with a nominal diameter of 6.11 mm, repeatable tolerance of ±0.001 mm and a 50 mm length; workshop-grade construction in special steel, supplied in a protective transport box. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed.

Gauge pin M323.611 — single gauge pin, 6.11 mm, ±0.001 mm (Metav IndustryLine)

The gauge pin M323.611 is a workshop‑grade, single reference pin designed for precise end‑measurements and verification tasks in production and inspection environments.

• High repeatability ±0.001 mm
• Workshop version in special steel
• Compact 50 mm length for tight fixtures
• Supplied in protective transport box

Precision where repeatability matters

A nominal diameter of 6.11 mm combined with a tolerance of ±0.001 mm provides a dependable reference for go/no‑go checks and comparative measurements. The extremely small tolerance reduces measurement uncertainty and supports consistent decision making during quality checks. The special steel construction keeps dimensional stability under routine handling, while the compact form factor makes the pin suitable for confined gauges and fixtures. This paragraph emphasises the operational benefit: faster inspection cycles with fewer ambiguous results, improving throughput without sacrificing traceability.

Built for workshop conditions and practical handling

Designed as a workshop version, the pin balances robustness with fine accuracy. At 50 mm overall length and a mass of 0.015 kg, the item is easy to position in tight assemblies and remains stable during contact measurements. The construction is aimed at routine use rather than delicate laboratory environments, so durability in daily production settings is a clear advantage. The delivery in a protective box reduces the risk of transport damage and helps preserve the reference geometry between uses.

Use cases and compatibility with inspection workflows

This single gauge pin is intended for end‑measurement tasks, calibration jigs, fixture setting and component verification. Its ±0.001 mm tolerance makes it suitable where high repeatability is required—such as batch acceptance testing or final inspection of turned and ground parts. The compact diameter and short length enable integration into small fixtures and modular inspection plates. Where traceability is needed, the pin’s defined geometry supports clear go/no‑go decisions and reliable position references within assembly processes.

Handling, maintenance and storage to retain accuracy

To maintain the pin’s performance, handle with clean, dry hands or gloves and avoid impacts. Store the item in its protective box between uses to prevent nicks and surface damage that would affect accuracy. Routine checks with a calibrated micrometre or a comparator are recommended if the pin is exposed to heavy handling; any visible wear or deformation should prompt replacement to avoid measurement drift. These simple measures preserve the pin’s benefits: consistent measurements, fewer rework loops and trustworthy inspection outcomes.

For workshop‑grade precision from Metav IndustryLine, contact Metav Werkzeuge in Emmerich for ordering and technical advice via info@metav-werkzeuge.com or +49 2822 7131930

Technical data

• SKU: M323.611
• GTIN: 4061905060403
• Category: Messstifte
• Label: Gauge pin, single, 6.11 mm, ±0.001 mm, length 50 mm

Facts

• Nominal diameter: 6.11 mm
• Length: 50 mm
• Tolerance / repeatability: ±0.001 mm
• Weight: 0.015 kg

Special features

• Material: special steel
• Workshop version
• Delivered in protective transport box
• Intended for end‑measurements and fixture checks

FAQ

What tolerance does the gauge pin offer?
The gauge pin M323.611 is specified with a repeatability of ±0.001 mm, making it suitable for high‑precision verification tasks.

Is the pin suitable for fixture setting and end‑measurements?
Yes, the M323.611 single gauge pin is intended for end‑measurements, fixture setting and go/no‑go checks in workshop inspection workflows.

Does the product come with a calibration certificate?
The product data does not indicate an ISO 17025 certificate for this item; please contact Metav Werkzeuge if an accredited calibration certificate is required.

How should the gauge pin be stored to keep accuracy?
Store the gauge pin in the supplied protective box, handle it with gloves, and avoid impacts; periodic checks with a calibrated micrometre are recommended to confirm continued dimensional accuracy.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com