6.92mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine

Ensure repeatable, shop-floor inspection with a compact gauge that combines micron-level accuracy and workshop durability: 6.92 mm nominal diameter, ±0.001 mm tolerance and 50 mm active length, supplied in a protective transport case. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed.

M323.692 gauge pin — 6.92 mm, ±0.001 mm, 50 mm length (Metav IndustryLine)

A precision M323.692 gauge pin designed for dimensional inspection and end-measure checks in metrology and quality‑control applications

• Workshop version for robust daily use
• Nominal diameter 6.92 mm with ±0.001 mm tolerance
• 50 mm hardened special-steel shaft
• Supplied in transport case for safe handling

Precision that secures production tolerances

A compact inspection pin with a 6.92 mm nominal diameter and ±0.001 mm tolerance delivers repeatable results where tight fits and end measurements matter. The declared deviation of ±0.001 mm (1 µm) positions this tool in the fine‑accuracy segment used for final checks, alignment gauges and verification fixtures. The close tolerance reduces measurement uncertainty during pass/fail inspections and supports consistent go/no‑go decision making on the shop floor, shortening cycle time by limiting rework.

Built for the workshop: durability and handling benefits

Produced in special steel and specified as a workshop version, the pin withstands regular handling and sliding contact in inspection routines. The 50 mm active length offers a practical balance between reach and stiffness for manual checks and fixture use, while the low mass supports quick positioning. Supplied in a protective transport case, the pin remains protected in transit and storage, preserving surface quality and dimensional integrity between uses — a benefit for repair shops and production lines alike.

Practical integration into inspection workflows

The compact design suits bench inspection, fixture integration and sample checks of mating parts. The straightforward geometry simplifies insertion into bores or sockets for end‑measure verification, enabling rapid comparative checks without complex set‑ups. Traceable ordering and identification via SKU make replenishment and inventory control efficient; the robust construction helps maintain consistent measurement behaviour across repetitive cycles, improving throughput and quality assurance.

For secure end‑measure verification with Metav IndustryLine accuracy, contact Metav Werkzeuge to order the M323.692 gauge pin or to request application advice via info@metav-werkzeuge.com or +49 2822 7131930

Technical data

• Article number: M323.692
• GTIN: 4061905059315
• Label: Prüfstift, einzeln, 6,92mm, +/- 0.001 mm Länge 50 mm

Numbers / Core technical data

• Diameter: 6.92 mm
• Tolerance: ±0.001 mm
• Length: 50 mm
• Weight: 0.019 kg

Design / Special features

• Material: special steel
• Workshop version
• Supplied in transport case
• Category: gauge pin / inspection pin
• SKU: M323.692

FAQ

What tolerance can be expected from this gauge pin?
The Metav IndustryLine M323.692 gauge pin is manufactured to a tolerance of ±0.001 mm, enabling micron‑level end‑measure checks for tight fitments.

What is the nominal diameter and length of the inspection pin?
The inspection pin has a nominal diameter of 6.92 mm and an active length of 50 mm, suitable for bore and end‑face verification.

Which material is used for the pin and what does that mean in practice?
The pin is made from special steel; this provides wear resistance and surface stability in routine workshop inspection tasks, supporting long service life under regular handling.

How is the product delivered to ensure protection?
The gauge pin is supplied in a protective transport case to prevent damage during storage and transit and to keep the measuring surface in good condition.

Can the M323.692 gauge pin be integrated into fixtures or jigs?
Yes, the compact geometry and workshop design allow straightforward integration into inspection fixtures and jigs for repeatable dimensional checks.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com