Precision chamfer milling cutters for efficient edge finishing
Chamfer milling cutters are steel-bodied tools fitted with indexable carbide inserts designed to economically deburr sharp edges, produce precise edge chamfers and prepare V-shaped weld grooves, improving assembly fit and part durability. These cutters are available with external coolant supply for accessible outer contours or with internal coolant channels that deliver pressurised coolant directly to each insert, which is essential when machining wide chamfers, heat‑generating materials or deep internal edges. The main benefits are reduced tooling costs since only the inserts require replacement, increased insert life through effective cooling and chip evacuation, and consistently high surface quality for subsequent processing. Key applications include general deburring, chamfering and weld preparation for metalworking, where throughput and reproducible results are critical.
35mm Chamfer Mill APKT 1604 Compatible, 75° Cutting Angle, 6 Flutes, 60mm Shank - Teknik Makina
Take advantage of the combination of robust toolholding, a defined 75° chamfer geometry and easy insert replacement for consistent edge finishes and reduced setup time; order the component via Metav Werkzeuge or contact the consultants for tailored advice. Chamfer mill T458TM — 75° cutting angle, 60 mm shank (Teknik Makina) A chamfer mill T458TM designed for precision edge chamfering in industrial machining, compatible with APKT 1604 indexable inserts 75° cutting angle for precise chamfers Compatible with APKT 1604 indexable inserts 60 mm shank for stable toolholding Six cutting edges for efficient material removal Consistent chamfer geometry for reliable production The T458TM delivers a defined 75° cutting angle, engineered to produce repeatable chamfers with minimal setup variance. The combination of a rigid 60 mm shank and a compact overall length of 50 mm stabilises the tool in the holder, reducing vibration and improving surface finish. With six cutting edges arranged to share the load, wear is distributed evenly, which extends insert life and sustains process reliability. This configuration supports lean production by lowering the frequency of rework and by helping to maintain tolerances across batch runs. Efficient indexable system that speeds up changeover Designed around indexable inserts APKT 1604 (compatible with Korloy), the cutter reduces downtime through quick insert indexing and replacement. The indexable system permits consistent edge geometry without complex regrinding, which simplifies tool management in busy workshops and small production lines alike. The combination of multiple cutting edges and replaceable inserts enhances throughput and provides a predictable cost-per-edge metric for job costing and process planning. Serviceable design with clear maintenance steps Insert retention uses a Torx screw specification M4x10 and the required key size is T15, enabling straightforward replacement and secure clamping. The tool's balanced mass (approx. 1.256 kg) and robust construction aid in stable cutting performance, while the compatibility with Korloy inserts broadens sourcing options for spares. For traceability and ordering, reference T458TM and Teknik Makina when selecting holders or replacement parts; the model’s design supports routine maintenance without specialised fixtures. For tailored technical advice on integrating the Teknik Makina chamfer mill into existing tool setups or to confirm suitability for a specific application, contact Metav Werkzeuge in Emmerich for expert guidance and stock information Technical data Article number: T458TM Manufacturer: Teknik Makina Insert type: APKT 1604 Compatible insert manufacturer: Korloy Torx screw: M4x10 Torx key: T15 Core specifications Cutting angle: 75° Shank diameter: 60 mm Overall length: 50 mm Cutting edges: 6 Weight: 1.256 kg Max. cutting diameter: 94 mm Nominal diameter: 35 mm Features & versions Compatible with indexable inserts APKT 1604 Insert supplier compatibility: Korloy Secure clamping via M4x10 Torx screw Balanced design for reduced vibration FAQ What insert type is required for this chamfer cutter? The cutter is specified for APKT 1604 indexable inserts; compatibility with Korloy inserts is indicated and recommended for optimal fit and performance. Which toolholder diameter does the cutter require? This tool uses a 60 mm shank for rigid mounting and stable toolholding during chamfering operations. How many cutting edges are provided and what is the benefit? The tool features six cutting edges, which distribute wear across multiple cutting faces and increase effective machining time between indexings. What is the specified cutting angle and what does it mean for applications? A 75° cutting angle provides a defined chamfer geometry suitable for standard edge preparation tasks, delivering consistent results for assemblies requiring controlled edge breaks. Which fastener and key are needed for insert changes? Insert retention uses an M4x10 Torx screw and requires a T15 Torx key for secure and repeatable replacement. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
39mm Chamfer Mill TCMT Inserts 36mm Cutting Height, 20mm Shank - Teknik Makina
Benefit from a robust indexable design with a Ø39 mm cutting diameter and 36 mm cutting height for reliable chamfering and minimal downtime; order the chamfer cutter directly via Metav Werkzeuge or consult our technical advisors for application support. Chamfer cutter S343TM — indexable-insert cutter, Ø39 mm, Teknik Makina The Chamfer cutter S343TM is an indexable-insert milling tool engineered for precise chamfering and bevel preparation in metalworking applications. Indexable system for TCMT 16T3 inserts Ø 39 mm diameter for medium chamfers 36 mm cutting height for deep chamfers 20 mm shank for stable clamping Faster chamfering with replaceable inserts The indexable concept offers a clear production advantage: rapid insert changes lead to reduced downtime and lower per-part costs compared with solid-tool replacements. Fitted for TCMT 16T3 inserts, the cutter accepts commonly available carbide inserts, enabling a quick insert change routine that is compatible with standard workshop stocking practices. This design supports steady throughput in repetitive chamfering tasks and helps maintain predictable edge quality across batches. Stable clamping for consistent edge quality A robust tooling foundation improves process reliability. The combination of a 20 mm shank and a tool Ø39 mm body keeps the cutter rigid in the holder, which reduces vibration and preserves surface finish. With a 36 mm cutting height and two cutting edges, the geometry provides steady material engagement for chamfers and bevels; the included 30° and 60° chamfer options allow selection of the best edge angle for a given part design. Consistent clamping and predictable chip formation translate into fewer reworks and a more controlled machining process. Practical workshop handling and maintenance Maintenance is straightforward: inserts are secured with an M3.5x8.5 Torx screw and serviced using a T15 key, simplifying routine changeover and reducing toolroom time. The tool’s 100 mm total length and compact mass (approx. 0.356 kg) make it easy to handle during toolprep and mounting, while the indexable concept lowers overall tooling inventory by allowing one cutter body to serve multiple insert life cycles. For production environments that value both uptime and cost-efficiency, this cutter forms a pragmatic part of a modular tooling strategy. Secure Teknik Cutting Tools' chamfer cutter S343TM through Metav Werkzeuge for dependable stock and application advice — contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 for specification assistance and order coordination Technical data Article number: S343TM Manufacturer: Teknik Makina SKU: S343TM Facts Diameter: 39 mm Shank diameter: 20 mm Cutting height: 36 mm Total length: 100 mm Cutting edges: 2 Weight: 0.356 kg Special features For indexable inserts TCMT 16T3 Chamfer angles: 30° and 60° Torx screw: M3.5x8.5 Torx key size: T15 FAQ What inserts are compatible with this cutter? The cutter is designed for TCMT 16T3 indexable inserts; TCMT 16T3 inserts fit the S343TM cutter and are commonly available from insert suppliers. How are inserts secured and changed? Inserts on the S343TM are fastened with an M3.5x8.5 Torx screw and require a T15 Torx key for secure and repeatable replacement. Which chamfer angles does the tool provide? The cutter features geometries for 30° and 60° chamfers, enabling straightforward selection of the desired edge profile for bevel preparation. Is the shank suitable for standard tool holders? The 20 mm shank and 100 mm overall length are compatible with holders accepting 20 mm shanks; the rigid shank supports stable clamping and consistent machining results. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
43mm Chamfer Cutter 45/90° 3 Flute, 25mm Shank 37mm Cutting Height, 100mm Overall - Teknik Makina
Take advantage of a precise chamfering solution with a 43 mm cutting diameter, a 25 mm shank for rigid mounting and compatibility with economical TCMT 16T3 indexable inserts — a combination that keeps tooling costs low while improving process repeatability; order directly via Metav Werkzeuge or consult their specialists for integration advice. Chamfer cutter S340TM — 43 mm diameter, TCMT 16T3 compatible (Teknik Makina) The Chamfer cutter S340TM is a compact, indexable-insert tool designed for producing clean 45° and 90° chamfers in machining setups where repeatability and quick insert changes are required. 43 mm cutting diameter Compatible with TCMT 16T3 inserts 45° and 90° chamfer angles 25 mm shank for secure clamping Consistent chamfers that reduce rework and setup time The S340TM delivers repeatable chamfer geometry thanks to a well-dimensioned cutting head and defined seating for indexable inserts. Using replaceable TCMT 16T3 inserts means the cutting edge can be renewed in seconds, lowering downtime compared with solid cutters. The tool’s 3 cutting edges and dedicated clamping ensure stable cutting conditions, reducing the likelihood of rework and the time spent on manual deburring. For shops aiming to standardise edge treatments, this cutter offers a predictable, measurable result for both 45° and 90° chamfers. Rigid build for industrial use and reliable toolholding Designed with a 25 mm shank and a 100 mm overall length, the tool provides a balance of reach and stiffness suited to many common holders and collet systems that accept 25 mm shanks. The moderate weight (0.634 kg) and compact design contribute to lower vibration during chamfering passes, which supports longer insert life and a cleaner surface finish. Fast and secure insert fastening is provided by the M3.5x8.5 Torx screw with a T15 key, giving straightforward maintenance and minimal accessory complexity for production environments. Economical operation through indexable inserts and controlled chip management By accepting standard TCMT 16T3 inserts, the cutter minimises tooling costs and simplifies inventory: only the small triangular inserts need replacing rather than entire cutters. The 37 mm cutting height and the cutter’s diameter are dimensioned to produce stable chip evacuation for typical chamfering depths, supporting efficient cycle times and consistent part quality. Compatibility with two common chamfer angles (45° and 90°) makes the cutter versatile across a range of finishing tasks without multiple dedicated tools. Contact Metav Werkzeuge to discuss integrating the Teknik Makina Chamfer cutter S340TM into the tooling portfolio or to request tailored advice from their technical consultants via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: S340TM Brand: Teknik Makina SKU: S340TM Facts Cutting diameter: 43 mm Shank diameter: 25 mm Cutting height: 37 mm Overall length: 100 mm Weight: 0.634 kg Cutting edges: 3 Chamfer angles: 45° / 90° Special features For indexable inserts TCMT 16T3 Torx screw M3.5x8.5 Torx key size T15 Designed for chamfering operations FAQ What insert type does the chamfer cutter require? The chamfer cutter S340TM is designed for TCMT 16T3 indexable inserts, offering quick replacement and economical running costs. Which chamfer angles can be produced with this cutter? The tool is configured to produce defined 45° and 90° chamfers, enabling consistent edge geometry without additional tool changes. What are the key dimensions for toolholding compatibility? The cutter has a 25 mm shank and 100 mm overall length, suitable for holders and collets that accept a 25 mm diameter shaft. How many cutting edges are available on the head? The cutter features 3 cutting edges, arranged to provide stable cutting and straightforward rotation of insert positions as required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
53mm Chamfer Cutter 45°/90° 3 Cutting Edges 37mm Cutting Height 25mm Shank - Teknik Makina
Benefit from precise chamfering with a Ø53 mm cutter that accepts TCMT 16T3 indexable inserts and offers both 45° and 90° chamfer options; the 25 mm shank provides secure clamping for repeatable results. Order the tool directly via Metav Werkzeuge or consult their specialists for application guidance. Chamfer Cutter S342TM – indexable cutter, Ø53 mm, 45°/90° chamfers (Teknik Makina) The Chamfer Cutter S342TM is an indexable milling cutter designed for efficient production of 45° and 90° chamfers in machining and workshop environments, suitable for use on milling heads and CNC toolholders. Indexable for TCMT 16T3 inserts 45° and 90° chamfer angles Ø53 mm diameter, 3 cutting edges 25 mm shank for secure clamping Deliver consistent chamfers and improved assembly fit The cutter delivers repeatable results thanks to its Ø53 mm body and a three‑edge cutting configuration that stabilises cutting forces. Chamfers at 45° and 90° are produced without additional setup changes, which simplifies jigging and reduces rework. The measurable cutting height 37 mm allows predictable material removal per pass, enabling planners to calculate cycle times and tolerances with confidence. This component is aimed at production workshops and contract manufacturers where process reliability is prioritised. Faster tool changes and reduced downtime with indexable inserts Designed for indexable operation, the tool accepts TCMT 16T3 inserts that are commonly stocked and quickly replaced. The use of indexable inserts minimises tool change time and keeps machining uptime high; insert indexing restores original geometry without regrinding. Fixing is executed with a Torx screw M3.5x8.5 and maintenance or replacement torque is applied via T15 drive tools. At a total length of 100 mm and a modest mass of 0.634 kg, the cutter offers good dynamic behaviour in automated spindles while remaining easy to handle during set‑up. Secure clamping and compatibility with common toolholders A 25 mm shank diameter ensures robust clamping in standard collets and hydraulic chucks, providing concentricity and resistance to deflection in interrupted cuts. The cutter’s design concentrates the cutting edges near the periphery for controlled chip evacuation and steady surface finish on chamfered edges. The product from Teknik Makina is suitable where quick indexability and predictable chamfer geometry are required in serial production or maintenance workshops, helping maintain process quality and assembly accuracy. Contact Metav Werkzeuge for tailored application advice on the Teknik Makina Chamfer Cutter S342TM and to arrange supply directly from Emmerich — email info@metav-werkzeuge.com or call +49 2822 7131930 for technical clarification and order support Technical Data Article number: S342TM Manufacturer: Teknik Makina Name: Chamfer Cutter S342TM Facts Diameter: 53 mm Cutting edges: 3 Total length: 100 mm Shank diameter: 25 mm Cutting height: 37 mm Chamfer angles: 45°, 90° Weight: 0.634 kg Torx screw: M3.5x8.5 Torx key: T15 Special features For indexable inserts TCMT 16T3 Indexable design for fast insert changes Three cutting edges for stable cutting Suitable for milling heads and CNC toolholders FAQ What insert type does this cutter use? The cutter is designed for TCMT 16T3 indexable inserts, which provide fast replacement and consistent geometry for chamfering operations. Can this tool produce both 45° and 90° chamfers? Yes, the tool is configured to machine chamfers at 45° and 90° angles, offering flexibility for assembly preparations and edge finishing. What is the shank diameter and will it fit standard holders? The tool has a 25 mm shank, which is compatible with common collets and toolholders used in milling and CNC applications. How many cutting edges does the cutter have and what is the total length? The cutter features 3 cutting edges and a total length of 100 mm, balancing stability with reach in typical workshop setups. Which screw and drive size secure the inserts? Inserts are secured with a Torx screw M3.5x8.5, tightened or released using a T15 Torx key. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
5mm Adjustable Chamfer Cutter 10°–80° Cutting Diameter 34mm Shank 25mm - Teknik Makina
Take advantage of the adjustable 10°–80° angle range, the stable 25 mm shank and compatibility with TCMT 16T3 indexable inserts for precise, repeatable chamfering in production environments; order the cutter directly via Metav Werkzeuge or consult our experts for application advice. Adjustable Chamfer Cutter by Teknik Makina — 10°–80° angle, accepts TCMT 16T3 The Adjustable Chamfer Cutter is an indexable chamfering tool engineered for flexible bevel creation across a range of production and workshop tasks. Adjustable angle 10°–80° 25 mm shank for rigid clamping Max cutting diameter 34 mm Compatible with TCMT 16T3 inserts Flexible bevel control for varied chamfering tasks The adjustable design provides an immediate benefit in setups that require multiple bevels: the 10°–80° angle range permits rapid switching between shallow and steep chamfers without changing the tool body. This flexibility reduces downtime and simplifies tool inventories in small batches or mixed-production runs. The mechanism is optimised for repeatability, so every setting change maintains consistent edge geometry — important when tolerances are tight and finish quality matters. Rigid mounting and insert-based economy A 25 mm shank ensures secure clamping for stable cutting conditions, while a maximum cutting diameter of 34 mm defines the tool’s working envelope. Compatibility with TCMT 16T3 indexable inserts delivers the usual indexable-tool advantages: fast insert changes, consistent cutting edges and cost-efficient reconditioning compared with brazed cutters. The cutter is supplied with a Torx fastening system (M3.5×8.5 screw, T15 key) for reliable insert retention and straightforward maintenance. Practical handling and workshop integration Weighing just 0.37 kg, the tool balances ease of handling with industrial robustness, making it suitable for both bench-mounted operations and longer production runs where tool change ergonomics matter. The cutter’s modular concept supports standard indexable-insert workflows and simplifies spare-part logistics. For application-specific questions or to confirm fitment in a particular holder, Metav Werkzeuge can advise on the correct clamping and insert choices to match existing toolholders and machine systems. Contact Metav Werkzeuge for tailored application advice on the Teknik Makina adjustable chamfer cutter and secure reliable supply directly from Emmerich. Technical data Article number: AH15TM Manufacturer: Teknik Makina Designation: Adjustable chamfer cutter Core specifications Angle range: 10°–80° Max cutting diameter: 34 mm Shank diameter: 25 mm Weight: 0.37 kg Features and compatibility Inserts: TCMT 16T3 Torx screw: M3.5×8.5 Torx key: T15 Flexible holder designation: S1474 FAQ What angle range can be set with this cutter? The adjustable chamfer cutter by Teknik Makina can be set across a 10°–80° range to cover shallow to steep bevels. Which indexable inserts are compatible? Compatibility is specified for TCMT 16T3 inserts; the cutter uses these standard inserts for economical edge changes. What shank size is required for secure clamping? A 25 mm shank diameter provides the necessary rigidity for stable chamfering operations with this cutter. How is the insert secured on the cutter? Inserts are fastened with a Torx screw (M3.5×8.5) using a T15 key for reliable retention and simple servicing. Is the cutter suitable for production use? With a robust shank, indexable inserts and adjustable angles, the Teknik Makina chamfer cutter is intended for workshop and production environments where versatility and repeatability are required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
5mm Adjustable Chamfer Cutter for TCMT 16T3 Indexable Inserts with Internal Coolant, 34mm Cutting Diameter - Teknik Makina
Take advantage of the tool's adjustable chamfering and internal coolant to improve cycle consistency and extend insert life; the compact 25 mm shank and 100 mm overall length provide straightforward machine integration. Order the adjustable chamfer cutter directly via Metav Werkzeuge or ask the consultants for tailored advice. Adjustable Chamfer Cutter AH15-1TM — for TCMT 16T3 Indexable Inserts, 5 mm cutting diameter The Adjustable Chamfer Cutter AH15-1TM is a compact, indexable‑insert cutter engineered for precise chamfering tasks in small and medium production environments, compatible with TCMT 16T3 inserts. Adjustable chamfering for TCMT 16T3 inserts 5 mm nominal cutting diameter Internal coolant for improved tool life Faster, repeatable chamfering for production runs The adjustable design with support for TCMT 16T3 indexable inserts delivers a cost‑effective route to repeatable chamfers without equipping multiple solid tools. Using interchangeable inserts reduces downtime for regrinding; replacing a worn indexable insert is faster than reconditioning a solid cutter, helping to maintain cycle times. The tool’s adjustable geometry enables fine tuning of the chamfer depth and angle, supporting consistent component quality across batches. Consistent cooling that prolongs service intervals Built‑in internal coolant directs lubricant and cooling fluid close to the cutting edge, which reduces thermal loading on the insert and evacuates chips more effectively. For operations where thermal stability influences dimensional accuracy, the coolant feed helps preserve cutting edge integrity and delays wear, translating into fewer insert changes and longer uninterrupted production windows. This characteristic supports predictable maintenance planning on the shop floor. Robust shank and compact dimensions for easy integration With a 25 mm shank and an overall length of 100 mm, the cutter fits standard holder systems without requiring special adaptors, simplifying tool changeover. The modest weight of 0.37 kg contributes to machine spindle balance at moderate speeds and facilitates handling during set‑up. A maximum cutting diameter of 34 mm establishes the tool’s capability envelope while the 5 mm nominal cutter size addresses typical chamfer profiles found in fabrication and finishing workflows. Practical benefits for purchasing and workshop managers The modular approach—indexable inserts on an adjustable body—lowers total cost of ownership by separating the wear‑sensitive cutting edges from the more durable tool body. Stocking a set of TCMT 16T3 inserts allows fast on‑site replacements and reduces lead times compared with bespoke solid tools. The design is suitable where flexibility and reduced tooling inventory are priorities, enabling efficient adaptation to varying component designs. For a tailored recommendation on machining parameters or to secure the Teknik Makina adjustable chamfer cutter AH15-1TM via Metav Werkzeuge, contact Metav Werkzeuge for professional advice and supply options. Technical data Article number: AH15-1TM Label: 5mm Fasenfräser, verstellbar TCMT 16T3 L100mm mit Innenkühlung Manufacturer: Teknik Cutting Tools / Responsible: Metav Werkzeuge GmbH Facts Nominal diameter: 5 mm Maximum cutting diameter: 34 mm Shank diameter: 25 mm Overall length: 100 mm Weight: 0.37 kg SKU: AH15-1TM UID: AH15-1TM Special features Adjustable chamfer cutter design Compatible with TCMT 16T3 indexable inserts Internal coolant/feed-through coolant Compact shank for standard tool holders FAQ What inserts does this cutter accept? The cutter is designed for TCMT 16T3 indexable inserts and uses the standard insert geometry associated with that designation. Is coolant supported through the tool body? Yes, the tool features internal coolant to deliver cutting fluid close to the insert for better thermal control and chip evacuation. What are the main dimensions to check for holder compatibility? Key dimensions are the 25 mm shank diameter and 100 mm overall length, which determine holder fit and projection. Can worn inserts be replaced on the cutter? Worn TCMT 16T3 inserts can be removed and replaced on the cutter body without additional machining, enabling rapid tool service. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
5mm Adjustable Chamfer Mill for TCMT 1102 Indexable Inserts 27mm Cut Dia, Internal Coolant - Teknik Makina
Take advantage of adjustable chamfering, internal coolant and compatibility with TCMT 1102 indexable inserts for consistent, burr-free bevels in serial production; order the cutter directly via Metav Werkzeuge or consult our specialists for application advice. Adjustable Chamfer Milling Cutter AH10-1TM — 5 mm diameter, internal coolant (Teknik Makina) A compact adjustable chamfer milling cutter AH10-1TM designed for precise beveling with TCMT 1102 indexable inserts, optimised for repeatable edge preparation in workshop and production environments Adjustable chamfering for versatile bevel widths Internal coolant supply for improved tool life Shank Ø20 mm for secure, stable clamping Compatible with TCMT 1102 indexable inserts Precision chamfering that reduces rework The adjustable chamfering concept delivers reliable bevel widths without multiple tools, making setup more efficient and reducing rework. The tool is designed around the proven TCMT 1102 indexable inserts, so insert changes are quick and economical. As a result, process consistency is improved and cycle times are shortened. This configuration makes the cutter particularly suitable where repeatable edge geometry is required across batches, helping to maintain part tolerances with minimal intervention. Better cutting conditions with internal coolant Integrated internal coolant channels feed cutting fluid directly to the cutting zone, improving chip evacuation and cooling at the insert edge. The immediate cooling reduces thermal loading on the insert, which contributes to longer tool life and a superior surface finish on bevelled edges. The combination of a compact cutter body and coolant supply supports stable cutting at the specified dimensions, including a cutting diameter 27 mm and an overall length 100 mm, while keeping vibrations low through the shank Ø20 mm connection. Economical handling thanks to indexable inserts The use of indexable inserts makes servicing straightforward: worn cutting edges are replaced rather than the entire tool, cutting consumable costs and minimising downtime. The insert system supports rapid restoration of cutting performance and consistent geometry. For operations that value uptime and predictable maintenance schedules, the replaceable-insert approach offers a clear cost-benefit compared with solid-tool alternatives and keeps capital equipment utilisation high. Application flexibility for workshop and light production This adjustable chamfer cutter excels in tasks that require clean, precise bevels on metal components where a dedicated chamfering operation is needed. The compact design is suitable for integration into standard toolholders that accept a shank Ø20 mm connection. The product is identified as AH10-1TM and is manufactured by Teknik Makina; it complements typical cutting tool inventories and supports mixed-production environments where rapid changeover between operations is essential. Speak to Metav Werkzeuge for technical consultation on the AH10-1TM and fast supply from Emmerich — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: AH10-1TM Label: 5mm Fasenfräser, verstellbar TCMT 1102 L100mm mit Innenkühlung Manufacturer: Teknik Makina Measurements Diameter: 5 mm Maximum cutting diameter: 27 mm Overall length: 100 mm Shank diameter: 20 mm Weight: 0.241 kg Features Compatibility: TCMT 1102 indexable inserts Internal coolant: yes Adjustable chamfering Indexable insert system SKU for ordering: AH10-1TM FAQ Which indexable inserts are suitable for this cutter? The cutter uses TCMT 1102 inserts; the AH10-1TM is designed to accept these standard indexable inserts for easy replacement. How does the internal coolant improve performance? Internal coolant channels deliver fluid directly to the cutting edge, which helps the AH10-1TM maintain cutting stability, extend insert life and improve surface finish. What holder size is required for secure mounting? The cutter features a shank Ø20 mm, so a toolholder or collet that accepts a 20 mm shank is required for stable clamping. Can the chamfer width be adapted during production? Yes, the adjustable design allows adaptation of bevel dimensions to meet varying chamfer requirements without changing to a different cutter. What are the order reference and weight for logistics planning? Order under SKU AH10-1TM; the cutter weight is 0.241 kg. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
5mm Chamfer Cutter 130mm Overall, 32mm Shank, 2 Flutes - Teknik Makina
Take advantage of precise chamfering, robust clamping and Korloy compatibility for consistent production results; order the chamfer cutter directly via Metav Werkzeuge or ask our consultants if needed. 5 mm Chamfer Cutter L130 mm – Teknik Makina, 2 flutes, 32 mm shank A 5 mm chamfer cutter L130 mm designed for accurate edge preparation and light chamfering tasks in machining applications, suitable for use with Korloy indexable inserts. 5 mm cutting diameter for precise chamfers 130 mm overall length for deep reach 32 mm shank for secure clamping Compatible with Korloy indexable inserts Accurate chamfering that reduces rework and increases throughput The chamfer cutter delivers controlled edge formation with a 5 mm cutting diameter that is optimised for small, precise chamfers. The geometry of the cutting edges and the two-flute design focus on repeatable results, reducing the need for downstream deburring and rework. By standardising on a cutter that produces uniform chamfer profiles, shops can expect improved cycle consistency and a measurable uplift in overall process efficiency. Stability and runout control for cleaner finishes A substantial 32 mm shank provides the mechanical stability required for steady cutting, while the two cutting edges support a balanced tool load. The tool requires a T15 Torx key to secure the insert screw (type M3,5x11), which aids quick indexing and replacement when service is necessary. The combination of a robust shank and compact cutter head minimises vibration and runout, resulting in a cleaner finish and longer tool life under normal operating conditions. Designed for versatile chamfering tasks in production environments Engineered for edge preparation, bevel creation and light deburring, this cutter is compatible with Korloy indexable inserts to offer a cost-effective approach to consumable management. The overall length 130 mm and a cutting length 50 mm provide access to workpieces with restricted reach while maintaining sufficient engagement for stable cutting. The solution is suitable for batch production and workshop retooling where predictable chamfer geometry is an operational requirement. Practical handling and workshop integration Maintenance and insert changes require only a standard Torx drive; the specified T15 Torx interface and M3,5x11 screw form a simple, proven fastening method that supports rapid servicing. The cutter is identified as S359TM, enabling straightforward inventory tracking and reordering. Supplied through Metav’s distribution, the tool benefits from a European quality filter and reliable logistics, helping to keep toolrooms stocked and production uninterrupted. For robust, repeatable chamfers with Teknik Makina reliability, contact Metav Werkzeuge for technical advice and procurement — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: S359TM Manufacturer: Teknik Makina Product type: Chamfer cutter Article label: 5mm Fasenfräser L130mm Dimensions & core data Diameter: 5 mm Overall length: 130 mm Shank diameter: 32 mm Cutting length: 50 mm Number of flutes: 2 Features & compatibility Compatible with Korloy indexable inserts Torx key: T15 Torx screw: M3,5x11 ECLASS: 21180806 Category: Machining / Shank cutters FAQ What material systems is this cutter suitable for? The cutter S359TM from Teknik Makina is intended for general chamfering tasks; compatibility with specific materials depends on the chosen Korloy insert grade and machining parameters. How is the insert fastened and exchanged? Insert fixation uses a Torx screw M3,5x11 requiring a T15 Torx key; the S359TM design allows straightforward screw removal for rapid insert changes. What advantages does the 32 mm shank provide? A 32 mm shank increases clamping stability and reduces tool deflection, improving finish and dimensional consistency during chamfering operations. Can this cutter reach recessed or hard-to-access edges? With an overall length of 130 mm and a cutting length of 50 mm, the tool is configured to access moderately recessed edges while maintaining cutting stability. How many cutting edges does the cutter have and why does it matter? The tool features two flutes; this configuration balances chip evacuation and cutting stability for small to medium chamfer profiles. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
5mm Chamfer Cutter for XCET 3104 Indexable Inserts 130mm Overall Length, 32mm Shank - Teknik Makina
Take advantage of a robust combination of compatibility with XCET 3104 indexable inserts, precise 5 mm chamfering and a 32 mm shank for stable clamping — all designed to keep production flowing with minimal downtime. Order the tool directly via Metav Werkzeuge or ask the consultants for application advice. Chamfer Cutter S357TM (for XCET 3104 Indexable Inserts) — 5 mm, L 130 mm — Teknik Makina A chamfer cutter designed for use with XCET 3104 indexable inserts, intended for precision chamfering and bevel preparation in milling applications. Compatible with XCET 3104 inserts 5 mm cutting diameter 32 mm shank for stable clamping 130 mm overall length Precision chamfering with indexable inserts The tool is engineered for repeatable chamfering thanks to its use of XCET 3104 indexable inserts, which allow rapid replacement and consistent cutting geometry across production runs. With a 5 mm cutting diameter, the cutter provides a controlled chamfer width that simplifies downstream assembly and finishing. The replaceable insert system reduces tool-change time, lowering machine downtime and improving overall process efficiency. The combination of indexed inserts and a single, well-defined cutting edge gives predictable chip formation and a reliable surface finish. Rigidity and runout control for consistent edge quality Clamping stability has been prioritised: the 32 mm shank and the substantial overall length of 130 mm are balanced to offer both reach and torsional rigidity in typical milling setups. A 50 mm cutting length ensures sufficient engagement for bevel operations while limiting overhang to reduce runout. These dimensions contribute to uniform results part after part, particularly in setups where consistent chamfer depth and angle are essential. Stable clamping reduces vibration, which in turn preserves insert life and lowers scrap rates. Fast maintenance and secure fixing for industrial workflows Insert retention and serviceability are straightforward: the cutter uses a Torx retention screw M3.5x11, tightened with a T15 key, enabling quick and secure insert changes on the shop floor. Compatibility with Korloy insert variants offers flexibility in sourcing and grade selection according to the material being machined. The tool’s single cutting edge simplifies inspection and seating of the insert, making routine maintenance fast and predictable, which supports tight production schedules and well-ordered tool management. Suitable tasks and operational benefits Best placed in CNC milling and secondary chamfering operations, this chamfering tool improves edge preparation prior to welding, coating or assembly. The design supports high repeatability and easy integration into existing tool inventories that include XCET 3104 inserts. For procurement and logistics, Metav Werkzeuge provides centralised distribution and a quality filter from Emmerich, helping to reduce supplier complexity while ensuring reliable supply. The result is a pragmatic tool choice for workshops seeking to optimise cycle times and maintain consistent edge quality. For technical consultation on toolholder compatibility or to secure supply of the S357TM chamfer cutter from Teknik Makina, contact Metav Werkzeuge for tailored advice and prompt delivery from Emmerich. Technical data Article number: S357TM eClass: 21180806 Product type: Chamfer cutter Facts Diameter: 5 mm Overall length: 130 mm Shank diameter: 32 mm Cutting length: 50 mm Cutting edges: 1 Torx screw: M3.5x11 Torx key: T15 Special features Compatible with XCET 3104 indexable inserts Suitable for Korloy inserts Tool category: Shaft cutters (Schaftfräser) Manufacturer: Teknik Makina FAQ Which inserts fit this cutter? The cutter accepts XCET 3104 indexable inserts; it is compatible with Korloy grades for varied material applications. What are the critical dimensions for toolholding? The tool has a 32 mm shank and 130 mm overall length; ensure a matching toolholder for stable clamping and minimal runout. How are the inserts secured? Inserts are fixed with a M3.5x11 Torx screw and tightened using a T15 key for secure retention and rapid replacement. What machining tasks is the cutter intended for? Designed for precision chamfering and bevel preparation in milling operations, the cutter supports repeatable edge preparation prior to assembly or finishing. What is the cutting engagement length? The tool provides a 50 mm cutting length, suitable for many chamfering and secondary machining tasks. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
5mm Chamfer Cutter L130mm 2-Flute, T15 Torx Screw M3.5x11 - Teknik Makina
Take advantage of the combination of 5 mm cutting diameter, a 32 mm shank and a 130 mm overall length for stable, repeatable chamfering in series production; order the tool directly via Metav Werkzeuge or contact our consultants for application support. Teknik Makina Chamfer Cutter S358TM – 5 mm dia, L130 mm A Chamfer Cutter S358TM designed for precise edge preparation and fast insert changes in industrial milling and finishing processes. 5 mm cutting diameter 32 mm shank diameter Two cutting edges for clean chamfers Compatible with Korloy indexable inserts Consistent, repeatable chamfering for reduced rework The S358TM shaft-mounted chamfer cutter delivers controlled edge preparation where dimensional consistency matters. With a 5 mm cutting diameter and two cutting edges, the tool produces uniform chamfers that minimise secondary deburring and manual finishing work. For workshops aiming to tighten tolerances and reduce throughput variability, the cutter’s geometry supports reliable cycle times and predictable tool wear. The result is fewer rejects and shorter downstream processing, which directly benefits productivity planning in high-volume environments. Stable clamping and vibration reduction for better surface finish A 32 mm shank and a total length of 130 mm provide enhanced rigidity in most standard collet or chuck systems. This robust shank diameter reduces deflection during machining, helping to maintain a consistent cutting angle over the full length of the operation. The 50 mm cutting length balances reach with stiffness, enabling clean chamfer edges even on longer toolpaths. In practice, improved stability lowers the risk of chatter, optimises surface quality and prolongs the life of both the insert and the holder. Fast, secure insert changes and simple maintenance Designed for compatibility with Korloy indexable inserts, the tool streamlines insert replacement and reduces downtime. The insert is secured with an M3.5x11 Torx screw, tightened with a T15 Torx drive for repeatable clamping torque. This standardised fixing simplifies maintenance routines and spare-part management across mixed fleets. Clear, repeatable fastening reduces assembly errors and makes it easier to train workshop staff on correct insert handling, supporting consistent process reliability. Practical applications and process advantages This chamfer cutter is suited to precision chamfering and edge breaking in preparation for assembly, welding or coating. By integrating a dedicated chamfering tool into the machining sequence, shops can consolidate operations and cut overall cycle time. The design focuses on practical, measurable benefits: reproducible edge geometry, straightforward insert swaps and reduced operator intervention. For production-oriented environments that require dependable tooling, the S358TM contributes to smoother workflow and predictable output. For availability, specification matching or machining recommendations for the Teknik Makina chamfer cutter S358TM contact Metav Werkzeuge in Emmerich — phone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com Technical Data SKU: S358TM Label: 5mm Fasenfräser L130mm Manufacturer: Teknik Cutting Tools Facts Diameter: 5 mm Overall length: 130 mm Shank diameter: 32 mm Cutting length: 50 mm Number of cutting edges: 2 Torx screw: M3,5x11 Torx key size: T15 Special features Compatible with Korloy indexable inserts Shaft-mounted chamfer cutter design Suitable for industrial milling and finishing FAQ What cutting diameter does the tool use? The chamfer tool has a 5 mm cutting diameter, suitable for small, precise chamfers. Which shank size is required for clamping? The tool uses a 32 mm shank diameter, designed for stable clamping in compatible collets or holders. Which inserts are compatible with this cutter? The cutter is compatible with Korloy indexable inserts and uses an M3.5x11 Torx screw for secure fastening. What is the article number or SKU? The article number is S358TM, sold under the Teknik Makina chamfer cutter designation. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
5mm Chamfer Mill for TCMT 1102 Indexable Inserts 60/120° Cutting, 16mm Max Dia, 70mm - Teknik Makina
Take advantage of a compact, rigid chamfering solution that combines compatibility with TCMT 1102 indexable inserts and dual-angle chamfering (60° / 120°) for versatile edge preparation; order the tool directly via Metav Werkzeuge or consult the experts for application advice. Chamfer mill S335-1TM — Chamfering cutter for TCMT 1102 indexable inserts, Ø5 mm, L70 mm (Teknik Makina) The Chamfer mill S335-1TM is a purpose-built chamfering cutter for machining precise 60° and 120° chamfers using TCMT 1102 indexable inserts, suitable for CNC and toolroom operations. Compatible with TCMT 1102 indexable inserts Dual chamfer angles 60° and 120° 12 mm shank for secure clamping Compact 70 mm overall length Precise chamfers with an insert-based system that saves time The S335-1TM is engineered for repeatable chamfering using industry-standard indexable inserts. Its compatibility with TCMT 1102 inserts means insert replacement is fast and cost-effective compared with brazed tooling, while the dual-angle capability (60° and 120°) allows a single tool to cover multiple chamfer profiles. With a nominal diameter of Ø5 mm and a maximum cutting diameter of Ø16 mm, the cutter provides a flexible work range that reduces tool changes and increases uptime on batch runs. Short, rigid design that improves surface quality and stability A 12 mm shank combined with a 70 mm overall length keeps the toolholder engagement high and minimises overhang, which in turn reduces vibration and improves surface finish. The low mass (approx. 0.182 kg) contributes to dynamic stability at typical machining speeds, helping to extend insert life and maintain consistent edge geometry. These factors together result in measurable gains in process reliability and predictable cycle times for production environments. Fast serviceability with standard fixation components Maintenance and insert changes are straightforward: the cutter uses a Torx fastening system (key Torx T8) and M2.5x5.5 fixing screws, ensuring secure clamping and simple re-indexing of the single cutting edge. The single-edge arrangement simplifies insert handling and inventory, lowering the risk of assembly errors during changeover. Clear identification (SKU S335-1TM) streamlines replenishment and tool management in busy toolrooms. Designed for industrial chamfering tasks and flexible workflows This chamfering tool is aimed at workshops and CNC operations seeking a reliable insert-based option for edge preparation. By combining a compact form factor with standardised inserts, the cutter supports lean tooling strategies and reduces dependency on specialist brazed cutters. The result is a pragmatic balance of precision, convenience and predictable maintenance intervals, making it suitable for repeated chamfering, edge breaking and preparatory finishing in assembly-ready components. For tailored application advice or to purchase the Teknik Makina S335-1TM, contact Metav Werkzeuge for expert guidance and secure supply directly from Emmerich. Technical data Article number: S335-1TM Label: 5mm Fasenfräser TCMT 1102 L70mm Manufacturer: Teknik Makina Facts Nominal diameter: 5 mm Maximum cutting diameter: 16 mm Shank diameter: 12 mm Overall length: 70 mm Weight: 0.182 kg Cutting edges: 1 Chamfer angles: 60°, 120° Special features Compatible with TCMT 1102 indexable inserts Torx key: T8 Torx screw: M2.5x5.5 SKU: S335-1TM FAQ What inserts does the cutter accept? The S335-1TM accepts TCMT 1102 indexable inserts, enabling quick insert swaps and standardised replenishment. Can the tool produce both 60° and 120° chamfers? Yes, the cutter is designed for 60° and 120° chamfers, providing flexibility for different edge profiles. What shank diameter is required for the holder? The tool features a 12 mm shank, suitable for compatible collets and toolholders in the same diameter class. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
6mm Chamfer Cutter for TCMT 1102 Indexable Inserts 45°/90°, 21mm Diameter, L100mm - Teknik Makina
Take advantage of precise chamfering, simple insert compatibility and stable mounted performance for smooth shop-floor integration — order directly via Metav Werkzeuge or consult our specialists if needed. Chamfer cutter for TCMT 1102 indexable inserts (6 mm, L100 mm) — Teknik Makina Chamfer cutter for TCMT 1102 indexable inserts designed for reliable edge preparation and deburring in turning and light milling setups. Compact 6 mm cutting diameter for accurate chamfers Compatible with TCMT 1102 indexable inserts 20 mm shank for secure clamping in standard holders Available with 45° and 90° chamfer geometry Precision chamfering that reduces rework and cycle time The chamfering head is engineered for repeatable edge preparation, delivering consistent results when used with TCMT 1102 inserts. The small 6 mm cutting diameter and optimised cutter geometry ensure minimal material removal per pass, which reduces the need for secondary finishing. Indexable inserts allow fast regrinding cycles and predictable edge condition, turning a formerly manual or time-consuming operation into a controlled, measurable process that supports higher throughput and lower scrap rates. Robust shank and geometry for stable machining A 20 mm shank provides a rigid connection to standard toolholders, improving vibration resistance and surface finish stability. The tool’s L100 mm overall length and 21 mm maximum cutting diameter are balanced to give secure clamping while retaining accessibility in tighter setups. With two cutting edges, the cutter maintains a steady material engagement and straightforward balancing, making it suitable for continuous use in small-batch production and repair workshops where operator time and machine uptime are critical. Fast insert changes and workshop-ready fixing Designed for quick maintenance, the cutter accepts TCMT 1102 indexable inserts secured by a Torx screw ( M2.5x5.5 ) and tightened with a Torx T8 key, enabling swift insert replacement and reducing downtime. The dual-angle option ( 45° / 90° ) covers common chamfering tasks without tool changeovers, helping to streamline tool inventories. Supplied dimensions and standard fastening mean straightforward integration into existing tool setups and holders, supporting a fast return to productive machining after any service interval. Contact Metav Werkzeuge GmbH in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 to discuss suitability and availability of the Teknik Makina chamfer cutter compatible with TCMT 1102 inserts Technical data SKU: S334-1TM Manufacturer: Teknik Makina Product type: Chamfer cutter (Fasenfräser) ECLASS: 21180806 Facts Diameter: 6 mm Shank diameter: 20 mm Overall length: 100 mm Max cutting diameter: 21 mm Cutting edges: 2 Weight: 0.181 kg Chamfer angles: 45°, 90° Special features Compatible with TCMT 1102 indexable inserts Torx screw: M2.5x5.5 Torx key: T8 Category: Shank cutter (Schaftfräser) FAQ What inserts does this cutter accept? The cutter is made for TCMT 1102 indexable inserts; using the specified insert size ensures correct seating and cutting geometry. How is the insert secured to the cutter? Inserts are fixed with a Torx screw (M2.5x5.5) and tightened using a Torx T8 key for secure mounting and easy replacement. Which chamfer angles are available? The tool supports both 45° and 90° chamfer geometries, covering typical edge-preparation tasks without changing tools. What shank diameter is required for clamping? A 20 mm shank provides the recommended clamping diameter for stable mounting in standard holders. Is the cutter suitable for continuous workshop use? Yes; the combination of two cutting edges, standard fastening and a rigid 20 mm shank makes the cutter appropriate for regular production and maintenance tasks. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
8mm Chamfer Mill for TCMT 1102 Indexable Inserts 45°/90° 30mm Cutter Length, 16mm Shank - Teknik Makina
Combining an 8 mm cutting diameter with compatibility for TCMT 1102 indexable inserts and a sturdy 16 mm shank, this chamfer cutter delivers repeatable, shop-ready chamfering and countersinking in small-batch and serial production; order directly via Metav Werkzeuge or consult the technical team for specification matching. Chamfer cutter for TCMT 1102 indexable inserts — 8 mm, 16 mm shank A compact chamfering tool designed for precision edge preparation and countersinking in workshop and production environments, compatible with TCMT 1102 indexable inserts. Chamfer cutter for TCMT 1102 indexable inserts 8 mm cutting diameter, 16 mm shank 45° and 90° chamfer options Torx T8 screw system M2.5x5.5 Consistent chamfers for production workflows The chamfering tool is engineered to provide reliable and repeatable chamfers in diverse machining tasks. With a nominal cutting diameter of 8 mm and a maximum cutting diameter of 20 mm, the cutter suits precision tasks where edge geometry must be consistent across batches. The combination of a solid 16 mm shank and a 100 mm overall length ensures stable clamping in standard tool holders, reducing vibration and improving surface finish. For shops migrating from brazed cutters to indexable solutions, this tool simplifies insert changes and maintains process uptime. Flexible geometry: 45° and 90° options explained Two selectable chamfer angles—45° and 90°—enable both standard bevels and fuller countersinks without changing the tool body. The angles refer to the included chamfer geometry of the cutter body: a 45° configuration produces a common edge break used for assembly and deburring, while 90° supports seating and flush countersinking. Using indexable inserts (TCMT 1102) allows rapid adaptation of wear parts; inserts can be rotated or replaced without regrinding, which shortens maintenance intervals and lowers life-cycle costs while keeping machining tolerances tight. Practical assembly and maintenance features The cutter utilises a Torx fastening system (Torx T8 with M2.5x5.5 screw) for secure insert clamping and straightforward service. The two cutting edges provide a balance between cutting efficiency and chip evacuation for small chamfers and deburring passes. Replacement and adjustment are quick, requiring only a compatible Torx key, and the indexable concept reduces the need for precision grinding. Together these features contribute to higher machine utilisation and faster tool changes in busy production settings. Suitable applications and workplace benefits Ideal for general metalworking, fixture preparation and finishing operations, the tool performs well where controlled chamfer geometry is required on components prior to assembly or coating. The compact profile and modest weight support manual handling and quick tool setup at the machine. With clear compatibility for TCMT 1102 indexable inserts, the cutter integrates into existing insert inventories and enables predictable output quality across shifts and operators. Contact Metav Werkzeuge for application advice on Teknik Cutting Tools chamfer cutters; request specific insert recommendations or compatibility checks by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: S334-2TM Product type: Chamfer cutter Brand: Teknik Makina Compatible inserts: TCMT 1102 Cutting diameter: 8 mm Maximum cutting diameter: 20 mm Overall length: 100 mm Shank diameter: 16 mm Cutting length: 30 mm Number of cutting edges: 2 Weight: 0.192 kg Chamfer angles: 45°, 90° Torx key: T8 Torx screw: M2.5x5.5 For indexable inserts Category: Shank cutters (Schaftfräser) FAQ What insert type is required for this cutter? This cutter uses TCMT 1102 indexable inserts; the geometry and clamping suit standard TCMT 1102 grades. Can the tool produce both 45° and 90° chamfers? Yes, the cutter is supplied with geometry options for 45° and 90° chamfering to cover common edge-breaking and countersinking needs. What is the shank size and how does it affect stability? The tool features a 16 mm shank, which provides stable clamping in compatible holders and helps reduce vibration for improved surface finish. What is the maximum workable diameter with this tool? The cutter supports a maximum cutting diameter of 20 mm, allowing for slightly larger chamfers or stepped operations when required. Which SKU identifies this product for ordering? Order reference is S334-2TM, Teknik Cutting Tools chamfer cutter for TCMT 1102 inserts. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
Precision chamfering for repeatable, economical edge finishing
Chamfering cutters for indexable inserts are steel carrier tools fitted with replaceable carbide cutting inserts, engineered to deburr sharp edges economically, produce precise bevels and prepare V‑shaped weld grooves. The design lets workshops renew cutting geometry simply by rotating or replacing worn inserts while the steel carrier body remains in service, reducing tooling cost and downtime.
How they work and where they belong in the workshop
These tools are used for conventional deburring and bevel creation on external contours as well as for preparing weld joints. In versions without internal coolant, the coolant or compressed air is directed at the tool from external machine nozzles, which is sufficient for well‑accessible outer contours and everyday deburring where chips can evacuate freely. Chamfering cutters fitted with internal coolant incorporate bores in the carrier that guide high‑pressure coolant directly to each insert. This targeted internal coolant supply is essential when machining wide chamfers, heat‑generating or hard‑to‑cut materials, or when bevelling deep inside components, because the high flush pressure removes chips effectively and reduces thermal load on the cutting edges.
Tangible benefits that improve production metrics
- Reduced tooling expenditure thanks to indexable inserts that are rotated or exchanged instead of replacing the whole cutter.
- Increased uptime and shorter changeover times through modular insert systems.
- Improved surface quality and consistent bevel geometry when using internal coolant for demanding materials.
- Better chip control on open operations with external coolant and machine nozzle alignment.
- Longer insert life and lower thermal wear under high‑pressure coolant conditions.
Why Metav is the practical choice for B2B buyers
Metav stands for democratisation of precision. As an experienced precision partner, Metav combines decades of application know‑how with a comprehensive range that covers every stage from measurement to machining accessories. With more than 48,000 customers, a catalogue of over 250,000 products and a central quality hub in Emmerich, Metav offers a reliable supply chain and specialist advice for selecting the right chamfering cutters and coolant configuration for each application. Metav’s range is positioned as the smart, quality‑first choice for industry, trade and specialist distributors.
Core summary
Chamfering cutters for indexable inserts deliver cost‑effective, repeatable edge preparation and weld‑groove formation by combining a reusable steel carrier body with easily replaceable indexable inserts and selectable coolant options. They are the pragmatic tool for workshops seeking consistent bevels and maximised tool life.
FAQ
When should I choose a chamfering cutter with internal coolant?
Choose a chamfering cutter with internal coolant when you need to machine wide chamfers, work with heat‑sensitive or hard‑to‑cut materials, or reach deep internal edges. The internal high‑pressure coolant directs flushing precisely to each insert, improving chip evacuation and reducing thermal wear on chamfering cutters.
Can chamfering cutters be used to prepare V‑shaped weld grooves?
Yes. Chamfering cutters for indexable inserts are commonly used to prepare clean, consistent V‑shaped weld grooves; their replaceable inserts permit economical reconditioning of cutting geometry between welding batches.
How are worn inserts replaced on these cutters?
Worn inserts are indexed or replaced individually on the cutter body, allowing the steel carrier body to remain in use. This modular approach lowers consumable cost and reduces machine downtime compared with solid cutters.
Which applications are suitable for cutters without internal coolant?
Cutters without internal coolant are ideal for accessible external contours and routine deburring tasks where chips can escape freely and coolant delivered by machine nozzles provides sufficient cooling and lubrication.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com