200mm Fork Clamp Bar 14mm Slot For M12 M14 Clamping Screw, DIN 6315B - AMF
Take advantage of the combination of reliable clamping geometry, compatibility with standard clamping screws and straightforward integration into existing fixtures for uninterrupted workshop operation. Order the fork clamp bar directly via Metav Werkzeuge or consult the technical team for application-specific guidance. Fork clamp bar DIN 6315B, slot 14 mm, L 200 mm – AMF The Fork clamp bar DIN 6315B is a fork-style clamping element designed for fixture and workholding applications in metalworking and general workshop environments, compatible with standard M12 and M14 clamping screws. Fork clamp bar, DIN 6315B standard Slot width 14 mm for positive engagement Overall length 200 mm, compact installation Compatible with clamping screws M12 and M14 Secure clamping with standardised geometry The fork-style clamping element provides a repeatable clamping interface based on the DIN 6315B standard, ensuring predictable positioning and force transmission within fixtures. The 14 mm slot offers secure engagement with corresponding clamping screws, reducing lateral play and enabling stable clamping even under intermittent load changes. This standardised form factor simplifies part selection for production cells and jigs, lowering engineering time and increasing process reliability. Compact length that supports diverse fixtures With a 200 mm overall length, the component fits within space-restricted setups while delivering sufficient contact surface for reliable clamping. The compact dimensions facilitate use in modular clamping systems, specialised fixtures and retrofit operations where a full-length bar would be impractical. The short profile also aids in rapid handling during assembly operations and minimises interference with adjacent tooling. Engineered for compatibility with common clamping hardware Specified for use with M12 and M14 clamping screws, the fork clamp bar integrates seamlessly into prevailing workshop inventories and clamping architectures. Compatibility with these thread sizes means the element can be combined with a wide range of screws, studs and nuts without the need for bespoke fasteners. This interoperability reduces procurement complexity and supports quick replacement during maintenance cycles. Robust application focus and material expectations Designed as a clamping accessory for industrial use, the component exhibits a sturdy fork form that resists deformation under typical clamping forces. The geometry concentrates clamping loads through the slot and fork arms, which helps maintain alignment and reduces the risk of slippage. For applications requiring consistent hold-down pressure in machining or assembly, the fork clamp bar offers a pragmatic balance between mechanical simplicity and functional resilience. Integration advice and practical benefits The standardised profile is suitable for repeatable production setups and one-off jigs alike; the element can be mounted directly to fixture plates or incorporated into clamp arms. The clear specification of slot width and length allows planners to calculate engagement depth and leverage in advance, which supports cycle-time optimisation and predictable tool life. Traceable standards and simple interchangeability contribute to lower total cost of ownership across workshop fleets. For application advice or to arrange suitable delivery from stock, contact Metav Werkzeuge; technical consultants can advise on compatibility with existing clamping hardware and fixture layouts Technical Data Article number: 4000833025NW UID: 4000833025NW Brand: AMF Product type: Clamping bar (fork version) Facts Slot width: 14 mm Overall length: 200 mm Suitable for: M12, M14 Packaging unit: 1 Standard: DIN 6315B Additional values: A: 25; B2: 38; B3: 12; B4: 6 Special features Fork version (Gabelausführung) Designed for use with clamping screw M12 and M14 Compact design for restricted installation spaces FAQ What is the recommended screw size for this fork clamp bar? The fork clamp bar is specified for use with clamping screws M12 and M14, allowing integration with common workshop fastenings. Is the fork clamp bar compliant with any standard? Yes, the component follows the DIN 6315B standard, providing standardised geometry for predictable fixture behaviour. Can this clamping element be used in confined fixture spaces? Its 200 mm overall length and compact fork design make the element suitable for installations with limited clearance where conventional long bars would not fit. How does the 14 mm slot affect clamping performance? The 14 mm slot ensures positive engagement with matching screws, reducing lateral play and improving stability during machining or assembly processes. What should be considered when replacing an existing clamping bar? Attention to slot width, overall length and compatible screw size is essential; the fork clamp bar offers direct interchangeability where DIN 6315B geometry and M12/M14 hardware are already in use. Manufacturer: AMF; Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm Fork Clamp Bar Slot 18mm For M16 M18 Screw - AMF
Take advantage of the fork-style geometry, slot width 18 mm and 200 mm length to achieve stable, repeatable clamping with standard M16/M18 screws; the compact form factor supports efficient fixture layouts and faster setup. Order the component directly via Metav Werkzeuge or ask the consultants for application guidance. Fork clamping bar No. 6315GN – fork-style clamping bar with 18 mm slot, 200 mm length (AMF) Fork clamping bar No. 6315GN is a fork‑type clamping component designed for integration into standard clamping fixtures and supports secure engagement with M16 and M18 clamping screws Fork-style design for secure engagement Slot width 18 mm for standard clamping bars Length 200 mm for versatile workpieces Compatible with M16 and M18 clamping screws Consistent, repeatable grip for precision clamping The fork geometry provides a defined contact interface that reduces lateral movement and improves repeatability during machining and assembly tasks. With a slot width of 18 mm and an overall length of 200 mm, the component aligns with common clamping profiles, enabling reliable force transfer from the clamping screw to the workpiece. This results in fewer re‑set cycles and more consistent part quality, which is particularly beneficial in small‑batch production or jigs where positional accuracy matters. Faster set-up and easier fixture integration Standardised dimensions make the component straightforward to incorporate into existing fixture concepts, cutting time spent on adaptations. The fork design accepts M16 and M18 clamping screws, so conventional threaded clamping elements can be used without custom interfaces. This compatibility reduces procurement complexity and shortens assembly time, allowing shops to maintain throughput while simplifying the bill of materials for clamping systems. The clear geometry also simplifies CNC programming and manual positioning. Robust solution for industrial clamping applications Designed for repeatable use in workshop and production environments, the fork clamping bar supports typical clamping workflows and machine table arrangements. The open fork allows quick engagement with clamping screws and provides tactile feedback during tightening, which helps operators verify secure seating without extra gauges. Supplied as a single unit, the component is suited to both retrofit projects and new fixture builds where compact, dependable clamping elements are required. Contact Metav Werkzeuge for tailored advice on fixture integration or to secure the AMF fork clamping bar for the next production run; Metav Werkzeuge’s specialists in Emmerich provide practical support and reliable supply for precision clamping components Technical data Article number: 4000833040NW Product type: Clamping bar Brand: AMF Type designation: Fork version No. 6315GN Facts Slot width: 18 mm Length L1: 200 mm L2: 57 mm L3: 36 mm A: 30 B2: 50 B3: 28 Suitable for: M16, M18 Special features Fork-style execution For clamping screw M16, M18 Packaged unit: 1 Label: Gabelspanneisen No.6315GN Schlitz-B.18mm L.200mm FAQ Is the fork clamping bar compatible with M16 and M18 screws? Yes. The fork clamping bar No. 6315GN by AMF is specified for use with M16 and M18 clamping screws and is designed to accept those thread sizes directly. What are the slot and overall length dimensions? The component features a slot width of 18 mm and an overall usable length of 200 mm, dimensions that suit standard clamping arrangements. Can the component be used in existing clamping fixtures? Yes. The fork geometry and standard measurements allow straightforward integration into many existing fixture systems without major modification. Is the fork clamping bar suitable for precision repeatability tasks? The defined fork contact and standardised geometry support repeatable seating and consistent clamping force, making it suitable for precision clamping applications and repeatable setups. What is the article number for ordering? The article number (SKU) is 4000833040NW for the AMF fork clamping bar No. 6315GN Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm Fork Clamp Bar Slot 26mm For M24 Clamping Screw DIN 6315B - AMF
Take advantage of the proven combination of standard conformity, robust fork design and precise slot sizing for dependable workholding; order directly via Metav Werkzeuge or consult the team for integration advice. AMF Fork Clamping Wedge DIN 6315B — 26 mm slot, 200 mm overall length The AMF fork clamping wedge is a DIN 6315B-compliant clamping element in fork design, intended for workholding with an M24 clamping screw in machine tables and fixture assemblies. Fork design for confined setups DIN 6315B standardised compatibility 26 mm slot for M24 clamping screw 200 mm overall length for deep reach Reliable standardisation for faster setup and fewer interruptions The wedge is manufactured to the DIN 6315B specification, which ensures interchangeability and predictable behaviour in standardised fixtures. With a fork design that provides access around pre-installed components, the component supports quicker installation and reduced machine downtime. The combination of standard conformity and a clear mechanical interface delivers a rational advantage for production environments that demand consistent clamping results and minimal adjustment time. Practical geometry that makes clamping both precise and accessible A 26 mm slot dimension accepts the specified M24 clamping screw without compromise, translating thread engagement into repeatable clamping force. The 200 mm overall length offers extended reach for deeper jaws or thicker setups while maintaining alignment under load. This geometry reduces the need for bespoke adaptors and simplifies fixture design, so planners and technicians benefit from efficient assembly and improved repeatability when building or reconfiguring workholding systems. Integration-ready design and specification details for procurement Measured values and compliance simplify procurement and inventory management: the part ships as a single unit and integrates directly into DIN-based systems. The listed enrichment data (Axite values) supports sorting and selection where multiple variants are used in a clamping portfolio. As a robust, standardised component, this clamping wedge helps maintain a consistent quality level across jobs and workshops, supporting both small-scale maintenance and industrial fixture supply chains. Contact Metav Werkzeuge for product availability and tailored integration advice on the AMF fork clamping wedge (SKU 4000833032NW) — expert assistance from Emmerich for seamless delivery to the workshop Technical data SKU: 4000833032NW Manufacturer: AMF Product type: Clamping wedge Type: Fork design Standard: DIN 6315B Facts Slot width: 26 mm Overall length: 200 mm Suitable for clamping screw: M24 Packaging unit: 1 Special features Fork execution for component access Compliance with DIN 6315B Axite enrichment: A: 40; B2: 66; B3: 20; B4: 10 FAQ What clamping screw fits this wedge? The AMF fork clamping wedge is designed for use with an M24 clamping screw and a 26 mm slot to ensure correct thread engagement and reliable clamping. Is the wedge compatible with standard DIN fixtures? Yes, the component conforms to DIN 6315B, allowing direct integration into standardised fixture systems and simplifying interchangeability. Can the wedge reach deeper jaws or thicker setups? The 200 mm overall length provides extended reach for deeper jaws and thicker workpieces while maintaining alignment under load. How is the part supplied for inventory and ordering? The item is supplied in a packaging unit of one; reference the SKU 4000833032NW when ordering to ensure the correct variant is delivered. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm Fork Clamp Bar Slot Width 14mm For M12 M14 Clamping Screw - AMF
Benefit from robust fork-style clamping, precise fit and straightforward integration into existing fixtures for a dependable production flow; order the clamping bar directly via Metav Werkzeuge or consult our specialists if required. Fork-style clamping bar No. 6315GN – 14 mm slot, 200 mm length (AMF) A fork-style clamping bar No. 6315GN designed for machine-shop clamping operations and compatible with M12 and M14 clamping screws. Fork design for secure clamping 14 mm slot width 200 mm overall length Compatible with M12 and M14 screws Secure, repeatable clamping for routine setups The fork configuration delivers a stable contact surface that reduces lateral movement during clamping and supports repeatable workholding. The 14 mm slot provides a defined seating for clamp elements and is suitable for standard clamping hardware, while the 200 mm overall length keeps the workpiece engaged over a useful span. These measurable attributes translate into fewer setup iterations and a more predictable machining process, enhancing throughput without complex adjustments. Fast integration with standard clamping screws and fixtures Compatibility with M12 and M14 clamping screws enables quick assembly into existing fixture arrays and T-slot setups where those thread sizes are already in use. The fork-style geometry simplifies alignment of the clamping screw and mating components, which shortens assembly time and reduces the risk of misalignment. This component is intended to support efficient workflows by enabling straightforward retrofitting and faster changeovers in production and maintenance contexts. Practical considerations, serviceability and supplier trust Delivered as a single unit, the component is intended for direct installation into workshop clamp systems and requires only the corresponding M12 or M14 fastening hardware. For complex fixtures or unusual mounting conditions, technical clarification is available from Metav Werkzeuge to ensure correct selection and integration. Metav combines decades of precision experience, a broad product range and established supply reliability—backed by more than 48,000 satisfied customers—so buyers benefit from a dependable sourcing partner as well as the component itself. For tailored advice on implementing the AMF fork-style clamping bar No. 6315GN in a specific fixture or production line, contact Metav Werkzeuge in Emmerich by e‑mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 for fast, expert guidance and supply options. Technical data Article number: 4000833039NW Manufacturer: AMF Product: Clamping bar (fork design No. 6315GN) Packaging unit: 1 Label: Fork clamping bar No. 6315GN, slot 14 mm, length 200 mm, for clamping screws M12, M14, AMF Facts Slot width: 14 mm Overall length: 200 mm A: 25 mm B2: 40 mm B3: 24 mm L2: 47 mm L3: 30 mm Suitable for: M12, M14 Special features Fork design For use with clamping screws M12 and M14 Single-piece packaging (1) UID / SKU: 4000833039NW FAQ Which clamping screws are compatible? The fork-style clamping bar No. 6315GN (AMF) accepts M12 and M14 clamping screws; see SKU 4000833039NW for ordering. What are the key dimensions to check before fitting? The main dimensions are a 14 mm slot width and a 200 mm overall length for the AMF fork clamping bar No. 6315GN (SKU 4000833039NW). How is the component supplied? The AMF clamping bar No. 6315GN is supplied as a single unit (packaging unit 1). Is the fork clamping bar suitable for standard workshop fixtures? The fork geometry of the AMF No. 6315GN is intended for standard workshop clamping applications and integrates with fixtures designed for M12 or M14 screws. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm Fork Clamp Bar Slot Width 22mm For M20/M22 Clamping Screws DIN 6315B - AMF
Take advantage of the DIN 6315B fork design, the 22 mm engagement slot and compatibility with M20 / M22 clamping screws for dependable workshop fixturing; order the component directly via Metav Werkzeuge or consult the technical team if clarification is required. Fork clamping bar DIN 6315B — fork design, 22 mm slot, 200 mm length (AMF) A fork clamping bar DIN 6315B engineered for secure machine-table fixturing and modular clamping setups, compatible with common M20 and M22 clamping screws. Fork design to DIN 6315B standard Slot width 22 mm for secure engagement Length 200 mm for versatile clamping setups Compatible with M20 and M22 clamping screws Reliable standard compliance for precise fixture positioning Compliance with DIN 6315B ensures a defined geometry and repeatable engagement in serial or single-part clamping operations. The fork design locates and supports the clamping element, reducing lateral play and improving positional repeatability during tightening cycles. This standard conformity simplifies selection for production environments and supports consistent results across multiple fixturing stations, contributing to a more efficient machining workflow. Practical dimensions that reduce setup time The combination of a 22 mm engagement slot and 200 mm overall length provides a balance between reach and rigidity. The slot width matches common clamping screw heads, enabling seamless integration with M20 and M22 hardware and reducing the need for adapters. In practice, this compatibility accelerates fixture assembly and helps maintain constant clamp force distribution, which in turn reduces rework and machine idle time. Robust integration into workshop systems Designed as a modular element for clamping assemblies, the bar from AMF supports repeatable engagement and straightforward inventory management. The fork configuration pairs well with standard clamping screws, making it an economical choice for toolrooms and production lines that prioritise reliability and interchangeability. The clear specification and compact form support easy replacement and predictable behaviour in demanding everyday use. Order the AMF fork clamping bar via Metav Werkzeuge for dependable fixturing solutions — contact Metav Werkzeuge for technical consultation at info@metav-werkzeuge.com or by phone on +49 2822 7131930. Technical data Article number: 4000833029NW Label: Gabelspanneisen DIN 6315B Schlitz-B.22mm L.200mm f.Spannschraube M20,M22 AMF Product type: Clamping bar Model: Fork design Manufacturer: AMF Dimensions / Core data Slot width: 22 mm Length: 200 mm Packaging unit: 1 Axite enrichment: Addition: A: 40; B2: 52; B3: 15; B4: 10 Features / Applications Compatible with clamping screws M20, M22 DIN 6315B fork configuration Suitable for modular clamping systems and machine-table fixturing FAQ What standard does the fork clamping bar follow? The fork clamping bar follows the DIN 6315B standard, ensuring standardised geometry and predictable fixturing behaviour. Which clamping screws are compatible with this bar? Compatibility is provided for M20 and M22 clamping screws, allowing direct use with common workshop hardware. What are the slot width and overall length? The slot width is 22 mm and the overall length is 200 mm, designed to balance engagement and rigidity. Is this component suitable for automated fixture systems? Yes; the defined fork geometry and standardised dimensions make this bar appropriate for automated or modular clamping setups where repeatability is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm Fork Clamping Jaw Slot 18mm For M16 M18 Clamping Screw DIN 6315B - AMF
Benefit from a compact fork-style clamping solution that combines DIN 6315B conformity with an 18 mm slot and a 200 mm overall length, providing reliable engagement with M16 and M18 clamping screws for straightforward fixture integration. Order the component directly via Metav Werkzeuge or consult the technical advisors for specification matching and rapid delivery. Fork clamping bar DIN 6315B (AMF) — fork design with 18 mm slot, 200 mm length The fork clamping bar DIN 6315B is a compact fork‑style clamping element engineered for secure workholding in fixture and jig assemblies, compatible with common M16 and M18 tension screws. DIN 6315B conformity for standardised fit 18 mm slot width for secure fork engagement 200 mm overall length for extended reach Suitable for M16 and M18 clamping screws Reliable, standardised clamping for fixture construction Conformity to DIN 6315B ensures interchangeability and predictable mounting dimensions across fixtures and machine tables. The fork execution gives positive engagement around clamping screws and studs, reducing the risk of lateral displacement during tightening. For production environments where repeatability matters, the standardised geometry simplifies spare‑part management and minimises machine downtime by enabling direct replacement without reworking existing setups. Faster set‑up and simpler integration into existing assemblies With an overall length of 200 mm, the component offers additional reach compared with shorter clamping bars, which helps when accessing recessed or hard‑to‑reach clamping points. The 18 mm slot aligns with common fork interfaces and accepts M16 and M18 tension screws for secure fastening. This compatibility reduces adapter requirements and shortens assembly time, resulting in measurable gains in workshop efficiency and throughput. Practical design that supports daily workshop demands The fork design keeps assembly and inspection straightforward: the open slot simplifies mounting and visual checks, while the compact form factor minimises interference with adjacent tooling. Supplied in single units, each item is easy to store and replace as part of a modular fixturing strategy. The clear specification facilitates procurement and inventory control, supporting a predictable supply chain for production and maintenance teams. Typical applications and who benefits most This clamping element is intended for fixture builders, machine shops and maintenance departments requiring standardised fork‑type clamping for jigs, welding fixtures or machining fixtures. The product is especially suitable where conventional clamping screws (M16, M18) are already in use, enabling quick retrofits and consistent clamping performance across multiple workstations. Contact Metav Werkzeuge for tailored fixturing advice or order the fork clamping bar through Metav Werkzeuge to ensure precise compatibility with existing assemblies and prompt dispatch from Emmerich Technical Data Article number: 4000833027NW SKU: 4000833027NW Product type: Clamping bar Type: Fork design Brand: AMF Data Slot width: 18 mm Overall length: 200 mm Suitable for clamping screws: M16, M18 Packaging unit: 1 Axite enrichment: A: 30; B2: 48; B3: 15; B4: 8 Special features Conforms to DIN 6315B Fork execution for positive engagement Designed for use with tension/clamping screws M16 and M18 FAQ What standard does the clamping bar follow and why is this important? The clamping bar follows DIN 6315B, which guarantees standardised mounting dimensions and compatibility with fixtures and accessories designed to the same norm. Can the fork clamping bar be used with both M16 and M18 screws? Yes, the fork configuration is dimensioned for secure engagement with M16 and M18 clamping screws, allowing flexible use across common workshop fittings. Is the 200 mm length suitable for recessed clamping points? The 200 mm overall length provides additional reach for recessed or hard‑to‑access clamping locations, improving accessibility without major fixture alterations. How is the component supplied and identified for reordering? The item is supplied as a single unit (packaging unit 1) and can be reordered using the article number 4000833027NW. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
22mm Clamp Bar Nr. 6314V Height 19-105mm M20 Thread With M20x22x200 Clamping Screw - AMF
Take advantage of a compact, adaptable clamping solution with a 22 mm T‑slot interface, an adjustable clamping height of 19–105 mm and a robust M20 thread for standard clamping screws; order directly via Metav Werkzeuge or consult our specialists for integration advice. Spanneisen Nr. 6314V – Clamping arm for 22 mm T‑slot, H 19–105 mm (AMF) A Spanneisen Nr. 6314V provides versatile clamping for workshop and production fixturing, designed to engage 22 mm T‑slots and accept standard M20 clamping screws. For 22 mm T‑slot tables Adjustable clamping height 19–105 mm Thread M20 for standard clamping screws Compact 160 mm overall length Secure, adaptable clamping that speeds up setup times The clamping arm is configured for direct integration with machines and fixtures that use a 22 mm T‑slot, allowing quick attachment and repeatable positioning. The broad clamping height 19–105 mm range enables handling of varied workpiece sizes without multiple intermediate components, which reduces setup changes and minimises downtime. This adaptability supports lean workflows and helps maintain consistent clamping pressure across production runs. Standardised thread for reliable force transmission Equipped to accept an M20 thread, the component pairs with common clamping screws such as M20 x 22 x 200, delivering secure and predictable holding force for machining and assembly operations. Using established thread standards simplifies maintenance and replacement, so clamp assemblies remain serviceable with off‑the‑shelf fasteners. The standardised interface therefore contributes directly to operational reliability and easier spare‑part management. Compact footprint and clear dimensional data for easy planning With a 160 mm overall length and 22 mm width, the clamping arm fits into tight fixture layouts while providing a stable lever for clamping actions. The concise dimensional profile supports efficient nesting on modular fixturing plate systems and helps planners calculate clearances quickly. Clear numeric specifications make the component straightforward to include in CAD layouts or BOMs, reducing ambiguity during procurement and installation. For dependable clamping in standard T‑slot setups, request the AMF clamping arm Nr. 6314V via Metav Werkzeuge — our consultants at Metav Werkzeuge will advise on compatibility and order fulfilment to ensure rapid integration into existing jig and fixture systems Technical data Article number: 4000603038NW Type: Nr. 6314V Product type: Clamping arm Manufacturer: AMF Packing unit: 1 Key measurements Clamping height: 19–105 mm T‑slot: 22 mm Width: 22 mm Overall length: 160 mm Thread: M20 Special features Compatible clamping screw: M20 x 22 x 200 Additional dimensions: A: 30; B2: 60; E1: 30; E2: 60; LS: 109 FAQ What T‑slot size is this clamping arm designed for? This clamping arm is designed for a 22 mm T‑slot and is supplied as the Spanneisen Nr. 6314V (AMF, SKU 4000603038NW) for direct mounting in standard 22 mm table slots. What is the clamping height range and why does it matter? The clamping height range is 19–105 mm; this range allows the Spanneisen Nr. 6314V to secure a wide variety of workpiece heights without additional spacers, improving fixture flexibility. Which clamping screw fits the assembly? The assembly is compatible with an M20 x 22 x 200 clamping screw as indicated in the component data; using this standard fastener ensures correct engagement with the M20 thread. Can this clamping arm be used in modular jig systems and CNC fixtures? Yes, the compact design and standard interfaces make the Spanneisen Nr. 6314V suitable for modular jig systems and CNC fixtures where a 22 mm T‑slot and M20 clamping are employed. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
250mm Fork Clamp Bar No.6315GN Slotted 22mm For M20 M22 Tension Screw - AMF
Combining a robust fork design, a 22 mm slot width and a 250 mm length delivers stable, repeatable clamping for standard fixtures; compatible with both M20 and M22 clamping screws to reduce setup complexity. Order directly via Metav Werkzeuge or contact our consultants for specification checks. Gabelspanneisen No. 6315GN — Fork clamping wedge, 22 mm slot, 250 mm length (AMF) Gabelspanneisen No. 6315GN is a fork-style clamping wedge designed for secure workholding where standard clamping screws M20 and M22 are used, offering dependable positioning for a variety of workshop fixturing tasks. Fork design No. 6315GN for secure clamping Slot width 22 mm for standard fixtures Length 250 mm for deeper engagement Compatible with M20 and M22 clamping screws Reliable clamping for consistent setups The fork-style clamping wedge provides a straightforward way to convert vertical screw force into lateral clamping pressure, enabling secure fixturing with minimal additional components. The combination of a 22 mm slot and 250 mm length creates a stable contact area that reduces movement during machining or assembly, which improves process repeatability. Where repeatable positioning matters, the wedge form helps maintain alignment without complex adaptations, so changeovers become faster and less error-prone. Fits common screw standards to reduce changeover time Compatibility with both M20 and M22 clamping screws means the component integrates directly into many conventional clamping systems. This cross-compatibility lowers the need for specialised adapters and reduces downtime during tooling swaps. As a result, fixture planning can focus on productivity and cycle time rather than on bespoke hardware, delivering a practical efficiency gain for production and maintenance workflows. Designed for straightforward integration and handling The fork execution simplifies installation: orient the wedge, insert the screw and apply clamping force. Its geometry is aimed at dependable contact and straightforward alignment in vises or fixture assemblies, supporting consistent clamping force transfer. This clarity in function makes it suitable for assembly stations, machining fixtures and general workshop applications where robust, repeatable holding is required without elaborate setup procedures. Confidence in supply and technical support Sourcing components via a dedicated distributor ensures reliable availability and technical guidance. Metav’s role as a precision partner adds an assurance of quality and logistical transparency, backed by stock management from Emmerich. For teams consolidating suppliers or standardising on dependable clamping hardware, the combination of clear compatibility and supply-chain reliability reduces procurement complexity and supports long-term operational stability. Contact Metav Werkzeuge for a tailored specification check on the AMF fork clamping wedge No. 6315GN and advice on integrating it into existing fixtures — Metav Werkzeuge is ready to assist from Emmerich with product and technical support Technical data SKU: 4000833042NW UID: 4000833042NW Type: Fork execution No. 6315GN Product type: Clamping wedge Facts Slot width: 22 mm Length: 250 mm Compatible clamping screws: M20, M22 Package unit: 1 Special features Fork design for lateral clamping force Suitable for standard fixture systems Label: Gabelspanneisen No.6315GN Schlitz-B.22mm L.250mm f.Spannschraube M20,M22 AMF FAQ What is the primary application of this fork clamping wedge? The fork clamping wedge No. 6315GN by AMF is intended for secure workholding and fixture use where a 22 mm slot and 250 mm engagement improve positional stability. Can the wedge be used with both M20 and M22 screws? Yes, the component is compatible with clamping screws M20 and M22, enabling direct integration into common clamping systems. Is this component suitable for heavy-duty machining? The fork design and 250 mm length provide a stable contact area for robust fixturing; suitability for specific heavy-duty operations depends on the broader fixture and machine force. How does the fork geometry affect setup time? Fork geometry simplifies alignment and clamping force transfer, reducing the need for custom adapters and cutting down changeover time in workshop environments. Which SKU should be referenced when ordering or enquiring? Please reference SKU 4000833042NW when requesting availability or technical details for this AMF fork clamping wedge. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
250mm Fork Clamp Bar Slot 18mm For M16 M18 Clamping Screw DIN 6315B - AMF
Take advantage of a standardised fork design and clear dimensional data to streamline fixture assembly and maintenance. With a DIN 6315B specification and a 250 mm overall length the component offers predictable integration into production tooling; order directly via Metav Werkzeuge or consult our specialists for application advice. Fork clamp DIN 6315B – Slot B, 18 mm, 250 mm (AMF) A Fork clamp DIN 6315B engineered for straightforward fixture use and compatible with M16 and M18 clamping screws in industrial and workshop environments. DIN 6315B compatibility 18 mm slot width 250 mm overall length Suitable for M16 and M18 clamping screws Standardised fork design for predictable fixture integration The fork-style clamping bar follows the DIN 6315B specification, which ensures standardised mounting and interchangeability across fixtures. This reduces setup time and simplifies stock management, because components manufactured to common standards fit without modification. The fork geometry, described here as a fork clamp, provides a defined engagement point for clamping screws and locating elements, resulting in consistent positioning during repetitive operations. Where jigs and fixtures rely on repeatable interfaces, this conformity translates into fewer alignment checks and less downtime. Fast compatibility with common clamping screws for flexible setups Designed to accept M16 and M18 clamping screws, the forked clamping bar enables rapid adaptation to existing clamping arrangements. The combination of a 18 mm slot and fork configuration supports secure engagement with a range of screw diameters commonly used in production. For procurement and planning, the clear specification reduces uncertainty: the item is a straightforward solution for retrofitting or expanding clamping systems. If additional dimensional data or advice on screw selection is required, Metav Werkzeuge consultants can provide practical guidance to match the clamping forces and thread standards of the application. Clear dimensions for consistent clamping and maintenance With a 250 mm overall length, the component delivers an extended reach while maintaining a compact footprint suitable for many fixture layouts. The 18 mm slot offers a predictable seating surface that aids in distributing clamping loads and maintaining parallelism between workpiece and fixture. These measurable attributes support quality control and enable quick verification during routine inspection. The fork design also facilitates visual checks for wear or deformation—important for preserving process reliability—so scheduled maintenance can be planned on objective, dimension-based criteria rather than guesswork. For standardised clamping with AMF compatibility and fast supply from Emmerich, contact Metav Werkzeuge for tailored advice and reliable delivery. Technical Data Article number: 4000833028NW Manufacturer: AMF Product type: Clamping bar (fork version) Label: Fork clamp DIN 6315B – Slot B 18 mm L 250 mm for clamping screw M16, M18 Packaging unit: 1 Facts Slot width: 18 mm Overall length: 250 mm Suitable for: M16, M18 SKU: 4000833028NW Special features Standard: DIN 6315B Fork design Slot type: Slot B Brand: AMF FAQ What standard does this clamping bar conform to? The fork clamp conforms to DIN 6315B, providing a standardised interface for fixture and jig integration. Which clamping screws are compatible with the fork design? Compatibility is specified for M16 and M18 clamping screws; the 18 mm slot and fork profile accommodate these common thread sizes. What are the key dimensions to check when retrofitting into an existing fixture? Check the 250 mm overall length and 18 mm slot width to ensure correct reach and engagement with the clamping system; reference SKU 4000833028NW when ordering. Is this product suitable for serial production environments? Yes. The standardised design and clear dimensional specification make the forked clamping bar suitable for repeatable, serial production-fixture setups where interchangeability and predictable performance are priorities. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
250mm Fork Clamp Bar Slot 18mm For M16 M18 Clamping Screw, GN 6315GN - AMF
Take advantage of a fork-style clamping solution that combines precise slot geometry and standard screw compatibility to streamline fixture setup. The 18 mm slot width and 250 mm length ensure adaptable clamping reach and repeatable positioning; order directly via Metav Werkzeuge or request expert advice for system integration. Gabelspanneisen No. 6315GN — Fork clamping bar, slot 18 mm, L 250 mm (AMF) A Gabelausführung No. 6315GN fork clamping bar designed for secure fixture clamping with M16 and M18 clamping screws in workshop and industrial fixturing. Fork design for M16 and M18 clamping screws Slot width 18 mm for standard fixture bars Length 250 mm for versatile clamping reach Robust construction for workshop and industrial use Secure, repeatable clamping with fork geometry The fork-style clamping bar is engineered to provide consistent fixture alignment and stable force transmission when paired with standard clamping screws. The fork design holds the workpiece securely while allowing fast engagement/disengagement during changeovers, which reduces setup time and increases throughput. Compatible with common clamping thread sizes, the component is suited to both manual bench fixtures and automated clamping stations. Clear dimensions to simplify fixture planning Critical dimensions are provided for straightforward integration into existing tooling layouts: the slot width (18 mm) and overall length (250 mm) define the clamping envelope and reach. Additional dimensional references (A: 30; B2: 50; B3: 28; L1: 250; L2: 57; L3: 36) support CAD placement and ensure correct clearance for mating components. These measurable values allow accurate planning of clamp positions and prevent interference during operation. Designed for demanding workshop environments The component is intended for use in production and maintenance settings where reliability matters. The geometry and construction support repeated clamping cycles; this durability reduces the need for frequent replacements and contributes to steady machine availability. The design focuses on practical usability in metalworking and general workshop applications while remaining compatible with standard clamping systems. Easy integration into existing clamping systems Integration is facilitated by compatibility with M16 and M18 clamping screws and the standard 18 mm slot, enabling seamless substitution into common fixture arrangements. The part functions as a modular element within versatile clamping setups, allowing procurement teams to reduce SKUs by selecting a solution that interfaces with a wide range of accessories and screw types. For specification and layout assistance, technical consultation is available. For procurement or technical advice on the AMF fork clamping bar, contact Metav Werkzeuge in Emmerich for tailored assistance and reliable supply coordination via phone or email. Technical data Article number: 4000833041NW Model: Gabelausführung Nr. 6315GN Product type: Clamping bar Brand: AMF Packaging unit: 1 Facts Slot width: 18 mm Overall length: 250 mm A: 30 mm B2: 50 mm B3: 28 mm L1: 250 mm L2: 57 mm L3: 36 mm Compatible threads: M16, M18 Special features Fork version for positive engagement Standard slot for fixture compatibility Suitable for workshop and industrial fixturing Modular integration with clamping screws and accessories FAQ Which clamping screws are compatible with this fork clamping bar? The fork clamping bar is compatible with M16 and M18 clamping screws; refer to model No. 6315GN (SKU 4000833041NW) when specifying the thread interface. What are the slot width and overall length? The slot width is 18 mm and the overall length is 250 mm, dimensions that define the clamping envelope for fixture planning. Can this component be used in automated clamping stations? Yes; the fork design and standard dimensions allow integration into both manual fixtures and automated clamping systems for repeatable positioning. Which measurements aid CAD integration and mounting? Use the provided dimensional references (A: 30; B2: 50; B3: 28; L1: 250; L2: 57; L3: 36) to place the part accurately in assemblies and to verify clearances. How should the item be referenced when ordering or specifying? Reference the AMF fork clamping bar by model No. 6315GN and SKU 4000833041NW to ensure the correct part and dimensions are supplied. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
250mm Fork Clamp Iron No. 6315GN Slotted Jaw 26mm For M24 Clamping Screw, Addition A40 B2:70 B3:43 L1:250 L2:83 L3:56 - AMF
Take advantage of the fork design, 26 mm slot width and 250 mm overall length for dependable fixture clamping and straightforward integration into standard setups; Order the fork clamping wedge No. 6315GN directly via Metav Werkzeuge or ask our consultants if needed Fork clamping wedge No. 6315GN — Fork version clamping wedge with 26 mm slot and 250 mm length (AMF) The Fork clamping wedge No. 6315GN is a fork-style clamping wedge engineered for fixture and workholding applications with M24 clamping screws, combining a narrow slot profile with extended engagement length for stable part retention Fork design for secure clamping Slot width 26 mm for standard fixtures Length 250 mm for deep engagement Reliable holding power for fixture work The fork-style geometry offers a direct mechanical advantage: the fork design centres clamping force around the screw axis and provides a consistent contact surface. With a 26 mm slot width and compatibility with M24 clamping screws, this clamping wedge is intended for standardised fixture systems and simple retrofitting. The result is a predictable clamping behaviour that reduces setup time and ensures repeatable component positioning. Technical users will value the clear interface to existing clamping screws and the improved load distribution compared with single-point clamps. Dimensions that simplify integration and alignment Precise dimensions enable straightforward planning for jigs and fixtures: the overall engagement length 250 mm (L1) combines reach with rigidity, while the additional measured values (A: 40; B2: 70; B3: 43; L2: 83; L3: 56) describe the wedge geometry for correct seat and clearance design. These figures allow engineers to calculate lever arms and contact points accurately so that clamping forces are applied where intended. The measured geometry also supports CAD-based checks, avoiding trial-and-error on the shop floor and accelerating fixture build times. Robust workshop suitability and consistent performance Designed as a practical component for industrial workholding, the clamping wedge is supplied as a single unit for immediate use and is brand-marked by AMF. The straightforward construction focuses on reliable mechanical function and long service intervals when used within specified parameters. For procurement and tooling consolidation, the component integrates cleanly into a wider clamping system and supports stable production runs. If additional specification data or compatibility checks are required, technical advice is available to confirm fit and function in specialised setups. Contact Metav Werkzeuge for tailored specification support on the AMF fork clamping wedge No. 6315GN — phone +49 2822 7131930 or eMail info@metav-werkzeuge.com for prompt assistance and advice Technical data Article number: 4000833043NW SKU: 4000833043NW Type: Fork version No. 6315GN Label: Fork clamping wedge No.6315GN slot W.26mm L.250mm for clamping screw M24 AMF Brand: AMF Data Slot width: 26 mm L1 (overall length): 250 mm A: 40 B2: 70 B3: 43 L2: 83 L3: 56 Special features Product type: Clamping wedge Suitable for: M24 clamping screws Packaging unit: 1 UID: 4000833043NW FAQ What clamping screw size fits this wedge? The fork clamping wedge No. 6315GN is designed for use with M24 clamping screws and mates directly with standard M24 fixture hardware. What is the slot width and why does it matter? The wedge features a 26 mm slot width, which determines compatibility with mating fixture elements and ensures correct seating and force distribution during clamping. How long is the wedge and what does that mean for engagement? The overall engagement length is 250 mm (L1); this extended length increases contact area and enables deeper engagement in fixture assemblies for improved stability. Is the component supplied as a single unit? Yes, the AMF fork clamping wedge No. 6315GN is supplied as a single unit (packaging unit: 1) ready for immediate installation. Manufacturer: AMF; Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
250mm Fork Jaw Clamp Bar Slot 22mm For M20 M22 Clamping Screw DIN 6315B - AMF
Take advantage of a standard-compliant clamping solution that combines secure engagement and broad compatibility for efficient workshop workflows; the fork-style design and 22 mm slot work together to reduce setup time and simplify spare-part management — order via Metav Werkzeuge or ask their consultants for application advice. Fork-style clamping wedge DIN 6315B – 22 mm slot, 250 mm (AMF) A fork-style clamping wedge DIN 6315B for machine-table and fixture clamping, designed to accept M20 and M22 clamping screws for standardised, repeatable set-ups Fork design for secure clamping DIN 6315B standardised compatibility 22 mm slot for broad clamping range 250 mm length for deep workpieces Consistent, standardised clamping for production environments The DIN 6315B specification ensures interchangeability across fixtures and clamping systems, which reduces procurement complexity and downtime. As a fork-style clamping wedge, this component provides a reliable interface between the clamping screw and workpiece support; the 22 mm slot allows a wider range of jaw and bracket geometries to be engaged. In practical terms, conformity to the standard translates into predictable performance during repeat production runs and faster changeovers on the shop floor. Compatibility that speeds set-up and reduces inventory Designed to accept common thread sizes M20 and M22, the wedge eliminates the need for multiple specialised adapters. Fewer bespoke parts mean simplified inventory and quicker assembly: maintenance teams benefit from reduced search time and purchasing departments from lower SKUs. The specification-driven approach supports leaner stocking while maintaining flexibility for varied clamping tasks, making it suitable for both single-machine workshops and production lines. Robust engagement for secure workholding The fork design achieves positive engagement with the clamping screw, translating clamp force efficiently into holding power at the point of contact. This geometry improves stability during machining and finishing operations where consistent clamping pressure is required. The 250 mm overall length extends the usable reach of the clamping element, allowing secure support of longer or irregularly shaped workpieces without compromising access for tools or inspection. Practical benefits for workshop efficiency Using a standardised, heavy-duty clamping element simplifies both planning and daily operation. The clear specification (slot width 22 mm, length 250 mm) enables quick selection of complementary components and avoids ambiguous fittings that can interrupt production. For technicians and engineers, the component’s straightforward design reduces assembly steps and facilitates routine checks, contributing to steady throughput and fewer unplanned stops. For robust, standard-compliant clamping solutions from AMF, contact Metav Werkzeuge in Emmerich for tailored advice and reliable supply of compatible components. Technical data Article number: 4000833030NW Label: Gabelspanneisen DIN 6315B Schlitz-B.22mm L.250mm f.Spannschraube M20,M22 AMF Manufacturer: AMF Facts Slot width: 22 mm Overall length: 250 mm Suitable for: M20, M22 Packaging unit: 1 Special features Fork design Standard: DIN 6315B Product type: clamping wedge axite enrichment: A: 40; B2: 62; B3: 20; B4: 10 FAQ What clamping screw sizes does this wedge accept? The fork-style clamping wedge is specified for M20 and M22 clamping screws, ensuring compatibility with common machine-clamping hardware. Does the component comply with recognised standards? Yes, the element is manufactured to DIN 6315B, which supports interchangeability and predictable performance in fixture assemblies. What is the usable slot width and overall length? The wedge features a 22 mm slot width and an overall length of 250 mm, providing extended reach for deeper workpieces. Is this part suitable for series production and quick changeovers? The standardised design and common thread compatibility make the wedge well suited to series production, where repeatability and rapid set-up are priorities. How does the fork design improve clamping performance? The fork geometry ensures positive engagement with the clamping screw and directs clamp force effectively to the workpiece, improving stability during machining. Manufacturer: AMF; Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
250mm Fork Jaw Clamp Bar Slot B26mm For M24 Clamping Screw, DIN 6315B - AMF
Combine DIN 6315B conformity with a 26 mm fork slot and direct compatibility with M24 clamping screws to ensure consistent fixture alignment and faster setup; order the AMF fork clamp bar directly via Metav Werkzeuge or consult the technical team for integration advice. AMF Fork-Style Clamp Bar DIN 6315B — 26 mm Slot, 250 mm Length The AMF Fork-Style Clamp Bar DIN 6315B is a forked clamping bar designed for fixture and clamping systems, providing standardised mounting and secure engagement with M24 clamping screws. DIN 6315B compliant fork design 26 mm slot width for standard fixtures 250 mm overall length for versatile reach Compatible with M24 clamping screws Secure, standardised engagement for reliable fixtures The fork configuration delivers a positive mechanical engagement with clamping screws and fixture components, increasing repeatability in production and jig setups. Built to the DIN 6315B standard, this clamp bar supports interchangeability across systems that rely on standardised dimensions. The 26 mm slot width provides a defined seating for forks and keys, while the 250 mm overall length balances reach and stiffness for common workshop tasks. These characteristics reduce the need for custom adapters and simplify the alignment process in repetitive operations. Faster setup through measured compatibility and fewer adjustments Standard dimensioning and the intended fit for M24 clamping screws reduce setup time and minimise trial adjustments during changeovers. Where fixtures are exchanged frequently, the predictability of standard parts decreases downtime and streamlines assembly sequences. The fork variant ensures quick insertion and positive location, which is especially useful in modular clamping systems and routine production runs. This measured approach to compatibility supports more efficient workshop workflows and a lower error rate at the fixture stage. Practical integration for workshop and production environments Designed as a single, ready-to-fit component, the fork clamp bar suits both bench-level jigging and larger fixture assemblies in production. The fork-style clamp bar from AMF is supplied as an individual item, making it straightforward to replace or expand existing clamping arrays without overhauling the entire system. Its straightforward geometry allows easy inspection and verification of seating and wear, supporting predictable maintenance cycles and safer clamping conditions on the shop floor. For standardised, fork-style clamping choose the AMF fork clamp bar via Metav Werkzeuge — contact Metav Werkzeuge for technical guidance and prompt supply from Emmerich: info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number / SKU: 4000833033NW Type: Fork version Standard: DIN 6315B Product type: Clamp bar Slot width: 26 mm Overall length: 250 mm For clamping screw: M24 Manufacturer: AMF Packaged units: 1 Core data Slot width: 26 mm Total length: 250 mm For: M24 clamping screws Packaged units: 1 SKU: 4000833033NW Special features Fork-style execution for positive engagement DIN 6315B standardised dimensions Suitable for fixture and jig integration Supplied as single unit for easy replacement Axite enrichment values: A: 40; B2: 66; B3: 20; B4: 10 FAQ Is this clamp bar compatible with M24 clamping screws? Yes. The AMF fork clamp bar is designed specifically for use with M24 clamping screws and mates with standard M24 threaded clamping systems. What standard ensures interchangeability for this component? The clamp bar conforms to DIN 6315B, which ensures standardised dimensions and interchangeability within compatible fixture systems. What are the key dimensions to check before ordering? Check the fork slot width of 26 mm and the overall length of 250 mm to ensure fit with existing fixture components and required reach. How is the AMF fork clamp bar supplied? The product is supplied as a single unit (packaged unit: 1), suitable for direct replacement or integration into modular clamping setups. Where is this clamp bar typically used? This fork-style clamp bar is used in jigs, fixture systems and production clamping assemblies where standardised, repeatable clamping is required. Manufacturer: AMF; Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
315mm Fork Clamp Bar DIN 6315B Slot 22mm for M20 M22 Screw - AMF
Robust fork‑type construction with a 22 mm slot and 315 mm overall length ensures standard‑compliant interchangeability and reliable clamping for workshop fixtures; pair this with the compatibility for M20 and M22 clamping screws to reduce setup time and avoid mismatches. Order the AMF clamp bar directly via Metav Werkzeuge or consult our specialists for tailored application advice. AMF fork-type clamp bar — DIN 6315B, 22 mm slot, 315 mm The AMF fork-type clamp bar is a DIN‑compliant clamping component intended for secure fixture mounting where M20 and M22 clamping screws are used, ideal for workshop and production jigs. Fork-type clamp bar, DIN 6315B compliant 22 mm slot width for M20/M22 clamping screws 315 mm overall length for deeper clamping reach Designed for fast, repeatable fixture assembly Predictable, standard-compliant performance for less downtime Reliance on the DIN 6315B standard offers predictable interchangeability and simplifies procurement across production lines. Conformance to this specification means that replacement parts and mating components follow defined dimensions and tolerances, which reduces the risk of assembly errors and speeds up maintenance windows. The standard compliance also supports long‑term planning for spare part inventories and minimises unexpected compatibility issues during machine changeovers. Faster set‑up and secure holding with the fork design The fork execution and 22 mm slot width are engineered for compatibility with common clamping screws M20 and M22, enabling immediate engagement and secure axial support. The 315 mm overall length increases reach into deeper fixtures, so fewer intermediate adapters are required; this shortens set‑up times and simplifies toolholding routines. A clear mechanical restraint from the fork shape improves repeatability of clamping forces, translating into consistent part quality and fewer reworks. Practical workshop benefits and applications Made for routine use in jigs, fixtures and retrofit operations, this clamp bar supports efficient workshop workflows by reducing alignment complexity and avoiding bespoke machining for every fixture change. The simple geometry permits quick inspection and replacement, while the compatibility with widely used clamping screw sizes ensures broad applicability across turning, milling and assembly jigs. Delivered as a single unit (packaging unit 1, SKU 4000833031NW), the component is ready for immediate integration into existing clamping systems. Contact Metav Werkzeuge in Emmerich at +49 2822 7131930 or info@metav-werkzeuge.com to confirm fitment for your clamping screws and secure reliable supply of the AMF fork-type clamp bar (SKU 4000833031NW) Technical data Article number: 4000833031NW Brand: AMF Product type: Fork‑type clamp bar Packaging unit: 1 Facts Standard: DIN 6315B Slot width: 22 mm Overall length: 315 mm Suitable for: M20, M22 Special features Fork execution Label: Gabelspanneisen DIN 6315B Schlitz-B.22mm L.315mm f.Spannschraube M20,M22 AMF Type: Gabelausführung FAQ Which clamping screw sizes are compatible with this clamp bar? The clamp bar is designed for use with M20 and M22 clamping screws and provides a 22 mm slot to accommodate these thread sizes reliably. Is this component compliant with an established standard? Yes — the component conforms to DIN 6315B, ensuring dimensional compatibility with other standardised clamping elements. What advantages does the fork execution offer in a fixture? The fork‑type design enables positive engagement around the clamping screw and improves axial restraint, resulting in repeatable clamping and quicker assembly compared with non‑fork alternatives. How does the 315 mm length benefit workshop applications? An overall length of 315 mm gives additional reach into deeper fixtures, reducing the need for extenders or special adapters and speeding up set‑up operations. Is the part ready for immediate installation on delivery? The item is supplied as a single unit (packaging unit 1, SKU 4000833031NW) and is intended for direct integration into compatible fixture systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
315mm Fork Clamp Bar Slot Width 26mm For M24 Clamping Screw - AMF
A fork-style clamping bar offering secure fork engagement with a 26 mm slot and compatibility with M24 clamping screws, paired with a 315 mm length for extended reach — ideal for stable fixture setups and reduced repositioning. Order the clamp directly via Metav Werkzeuge or consult our advisors for specification support. Fork-style clamping bar No. 6315GN — 26 mm slot, 315 mm length (AMF) A fork-style clamping bar No. 6315GN engineered for machining fixtures and workshop clamping, designed to work with standard M24 clamping screws for dependable part retention in production environments. Fork design for reliable workpiece engagement 26 mm slit width for standard clamping screws 315 mm overall length for deep setups Compatible with M24 clamping screw Precision clamping for consistent machining The fork geometry provides a concentrated contact area that improves repeatability during clamping cycles. By combining a fork-style clamping bar with a defined 26 mm slot and suitability for M24 clamping screws, the element minimises lateral movement and maintains alignment under cutting forces. This leads to fewer micro-adjustments during setup and contributes to consistent part quality across batches. The design is particularly advantageous for fixtures where lateral stability and controlled clamping pressure are decisive for surface finish and dimensional tolerance. Built for workshop endurance and straightforward integration Constructed for integration into existing fixtures and bolting systems, the clamp’s 315 mm length gives additional reach, reducing the need for repositioning and allowing more flexible workpiece placement. Dimensional clearances such as A: 40 mm, B2: 70 mm and B3: 43 mm ensure predictable fitment in standard tooling plates and vice setups, while L2: 83 mm and L3: 56 mm define the engagement geometry for straightforward CAD placement. The uncomplicated form factor simplifies retrofitting and inventory management, making the component a pragmatic choice for production shops seeking reliable, low-complexity clamping solutions. Faster setups and safer handling in daily use Routine handling benefits from the fork profile because the workpiece can be located and clamped with fewer iterative adjustments, contributing to reduced setup time and lower cycle variability. The clear compatibility with M24 screws streamlines spare-part logistics and tooling standardisation, supporting lean workshop organisation and predictable maintenance intervals. For teams aiming to increase throughput without sacrificing safety or repeatability, this clamp provides a pragmatic balance between robust hold and uncomplicated assembly. For secure, standardised clamping with the AMF fork-style clamping bar No. 6315GN, contact Metav Werkzeuge for ordering and technical clarification — info@metav-werkzeuge.com or +49 2822 7131930 — our consultants will assist with specification matching and delivery options Technical Data Article number: 4000603071NW Manufacturer: AMF Product type: Clamping bar (spanneisen) Design: Fork version No. 6315GN Suitable for: M24 clamping screw Dimensions Slot width: 26 mm L1 overall length: 315 mm A: 40 mm B2: 70 mm B3: 43 mm L2: 83 mm L3: 56 mm Packaging unit: 1 Special features Fork execution for focused engagement Label: Gabelspanneisen No.6315GN Schlitz-B.26mm L.315mm f. Spannschraube M24 AMF SKU / UID: 4000603071NW FAQ What clamping screw fits this fork-style clamping bar? The fork-style clamping bar No. 6315GN from AMF is designed for use with an M24 clamping screw, providing standardised compatibility for common fixture systems. Which dimensions determine the installation depth and reach? Key installation dimensions are the overall length L1 = 315 mm and the slot width of 26 mm; additional clearance values are A = 40 mm, B2 = 70 mm and B3 = 43 mm as specified for fixture planning. Is this clamping bar suitable for retrofitting into existing fixtures? Yes, the geometry and standardised M24 interface make the clamp well suited for retrofitting and replacement in conventional machining and workshop fixtures. How is the product identified for ordering or spare parts? Order identification is via SKU 4000603071NW and the designation fork-style clamping bar No. 6315GN (AMF), which should be quoted for exact matching. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
315mm Fork Jaw Clamping Wedge Slot 22mm For M20 M22, Fork Design - AMF
Take advantage of a secure fork design and a precise 22 mm slot combined with a practical 315 mm length for reliable fixture clamping; benefit from compatibility with standard M20 and M22 clamping screws. Order the fork clamping wedge directly via Metav Werkzeuge or ask our consultants if needed. Fork clamping wedge No. 6315GN — Fork design, 22 mm slot, 315 mm length (AMF) The Fork clamping wedge No. 6315GN is a fork-style clamping element intended for fixture and vice applications, designed to accept M20 and M22 clamping screws for robust and repeatable workholding. Fork design for secure engagement Slot width 22 mm for standard fittings Length 315 mm for extended reach Compatible with M20 and M22 clamping screws Faster, more repeatable clamping for productive setups The fork-style execution provides a straightforward mechanical engagement that reduces setup time and increases repeatability. A 22 mm slot offers a defined contact area for standard clamping hardware, while the 315 mm length permits deeper reach or offset mounting in modular fixture assemblies. For production environments where cycle time and consistency matter, this clamping element translates directly into fewer re-adjustments and a steadier process flow. Broad compatibility that simplifies integration Designed to accept both M20 and M22 clamping screws, the component fits established clamping standards common in shop fixtures and machine vices. The fork geometry allows secure engagement with mating parts, which results in a stable clamping interface and reduced risk of slippage under load. Specifying this clamping wedge streamlines parts procurement and reduces the need for custom adapters in many typical workshop configurations. Practical handling and durability for everyday use The long form factor supports a variety of fixture arrangements while maintaining a compact footprint when mounted. The slotted engagement ensures quick placement and removal during changeovers, contributing to lower downtime. Although material specifics are not listed, the design focus is on mechanical reliability and workshop compatibility, making it suitable for repetitive industrial tasks where steadfast clamping is required. For procurement or tailored advice on integrating the AMF fork clamping wedge No. 6315GN into existing fixtures, contact Metav Werkzeuge for expert guidance and ordering assistance. Technical data Article number: 4000603070NW Type: Fork design No. 6315GN Product type: Clamping wedge Manufacturer: AMF Packaging unit: 1 Facts Slot width (B): 22 mm Length (L1): 315 mm Suitable for screws: M20, M22 Additional dimensions: A: 40; B2: 60; B3: 35; L2: 68; L3: 45 Design features Fork execution Slotted engagement For clamping screws M20 and M22 SKU/UID: 4000603070NW FAQ Which clamping screws are compatible with this fork clamp? The fork clamping wedge No. 6315GN from AMF is specified for use with M20 and M22 clamping screws, allowing integration with commonly used sizes in fixtures and machine vices. How does the fork design affect fixture stability? The fork execution provides a positive mechanical engagement that concentrates contact on the 22 mm slot, improving lateral stability and reducing the tendency for the clamped part to shift during machining. Is the clamping wedge suitable for deeper or offset mounting? Yes — the 315 mm length gives extended reach, which is advantageous for offset or deeper mounting arrangements within modular fixture systems. What dimensions should be checked before selection? Key dimensions are the 22 mm slot width and the 315 mm length; additional measures provided (A, B2, B3, L2, L3) help verify fit within the intended fixture geometry. Can the component be swapped quickly during tool changes? The slotted, fork-style interface is designed for straightforward placement and removal, enabling relatively fast changeovers and reducing downtime in repetitive operations. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
315mm Fork Style Clamping Iron Slot B.26mm For Clamping Screw M24 DIN 6315B - AMF
Take advantage of standardised compatibility and reliable clamping force: the combination of DIN 6315B conformity, a 26 mm slot and M24 screw compatibility ensures consistent seating and simple integration into existing fixtures. Order the fork-style clamping bar directly via Metav Werkzeuge or consult our advisers for application-specific guidance. Fork-style clamping bar DIN 6315B — 26 mm slot, 315 mm length (AMF) The Fork-style clamping bar delivers a standard-compliant clamping interface for vices and fixture systems, designed for secure use with M24 clamping screws. Fork design to fit M24 clamping screws DIN 6315B standardised interface 26 mm slot width for stable seating 315 mm overall length for versatile reach Reliable clamping through a standard interface The DIN 6315B conformity of this fork-style clamping element guarantees a predictable interface for fixtures and modular setups, reducing alignment guesswork during production planning. A 26 mm slot accurately locates the mating screw or pin and promotes repeatable contact conditions, which directly improves clamping accuracy and operational consistency. This standardised approach shortens set-up times in serial applications and facilitates interchangeability across clamping systems without additional adaptors. Fork design for secure force transfer and stability The fork configuration channels clamping loads into a defined contact zone, ensuring stable force transfer and limiting lateral movement during machining or assembly operations. With a 315 mm overall length, the component offers extended reach for deeper clamping positions while maintaining rigidity across its span. The geometry helps to distribute stress evenly, which preserves seat integrity and supports sustained performance in demanding workshop environments. Straightforward integration with M24 systems Designed specifically for use with M24 clamping screws, this clamping element fits seamlessly into established clamping architectures, avoiding the need for custom hardware. Compatibility with common screw sizes and the standard interface speeds procurement decisions and simplifies inventory management. The product’s straightforward mounting characteristics enable faster fixture changes and a leaner tooling footprint on the shopfloor, contributing to measurable workflow improvements. Practical benefits for workshop and production use Beyond basic compatibility, the fork-style clamp reduces handling complexity: the defined slot and standardised dimensions lower the risk of incorrect seating and support reliable repeatability from one operation to the next. Built for routine industrial use, the component supports consistent cycle times and helps maintain quality standards in both repair and production settings. The clear specification and industrial focus make it a practical choice where dependable clamping and straightforward maintenance are required. For purchasing advice, technical clarification or to specify the correct variant, contact Metav Werkzeuge in Emmerich for reliable delivery and expert assistance: info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number / SKU: 4000833034NW Manufacturer: AMF Product type: Spanneisen Standard: DIN 6315B Facts Slot width: 26 mm Overall length: 315 mm Compatible screw: M24 Packaging unit: 1 Special features Fork-style execution (Gabelausführung) Designed for clamping screw M24 Axite enrichment: A: 40; B2: 66; B3: 20; B4: 10 Label: Gabelspanneisen DIN 6315B Schlitz-B.26mm L.315mm f.Spannschraube M24 AMF FAQ What is the slot width of the fork-style clamping bar? The fork-style clamping bar features a 26 mm slot, which locates the clamping screw or locating pin for repeatable seating. Which clamping screw size is required for this component? This clamping element is designed for use with M24 clamping screws to match the DIN 6315B interface. What standard does this clamping bar conform to? The component conforms to DIN 6315B, ensuring compatibility with standardised fixture and clamping systems. What is the overall length and how does it affect use? The overall length is 315 mm, offering extended reach for deeper clamp positions while maintaining rigidity for stable operation. Can this part be used across different fixtures and vices? Yes — the DIN 6315B interface and M24 compatibility enable straightforward integration into a range of vices and modular fixture systems; the SKU for reference is 4000833034NW. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
500mm Fork Clamp Bar Slot B26mm For M24 Screw DIN 6315B - AMF
Benefit from a fork-style clamping bar built to DIN 6315B with a 26 mm slot and 500 mm overall length for secure M24 screw clamping and stable setups; this configuration streamlines fixture preparation and improves repeatability on the workshop floor. Order the clamping bar directly via Metav Werkzeuge or consult our advisors for specification support. Fork-style clamping bar (Gabelspanneisen) DIN 6315B — 26 mm slot, 500 mm — AMF The Fork-style clamping bar DIN 6315B is a precision clamping accessory designed for robust fixturing and long-reach applications, intended for use with an M24 clamping screw. Fork-style design for secure clamping DIN 6315B standardised compatibility 26 mm slot width for M24 clamping screw 500 mm overall length for long reach Faster setups through standardised compatibility Compliance with DIN 6315B ensures straightforward integration into existing fixturing systems, reducing the time spent selecting compatible parts. The 26 mm slot is sized for an M24 clamping screw, which simplifies procurement and lowers the risk of mismatched components. For production environments where quick changeovers and consistent alignment matter, the standardised interface delivers reduced setup time and repeatable positioning without the need to alter fixture geometry. Secure, repeatable clamping with extended reach The fork-style configuration concentrates clamping forces at two prongs, improving stability under load while maintaining accessibility to the workpiece. With a 500 mm overall length the bar provides long reach for larger or awkwardly placed components, enabling clamping closer to the machining area and reducing the need for secondary supports. The result is improved precision during operations that demand consistent contact pressure and minimal movement. Practical workshop integration and inventory benefits Supplied in a single packing unit, the bar is suited to standard clamping setups and simplifies inventory management for maintenance and production departments. The plain, standardised design supports modular fixturing concepts, allowing quick pairing with commonly used clamping screws and fixtures. By choosing components that match established norms, workshop planners achieve smoother ordering, fewer downtime risks and a leaner supplier landscape. For assured DIN 6315B compatibility and reliable delivery, contact Metav Werkzeuge to specify and proc ure the AMF fork-style clamping bar — email info@metav-werkzeuge.com or call +49 2822 7131930 for technical guidance and order processing. Technical data Article number: 4000603053NW Type: Fork version (Gabelausführung) Standard: DIN 6315B Product type: Clamping bar (Spanneisen) Brand: AMF Facts Slot width: 26 mm Overall length: 500 mm Suitable for: M24 clamping screw Packaging unit: 1 Special features Fork-style execution Slot for 26 mm clamp Axial enrichment: A: 50; B2: 66; B3: 20; B4: 10 DIN 6315B compatible FAQ What does the DIN 6315B designation mean for this clamping bar? DIN 6315B denotes the standardised interface and dimensions that the fork-style clamping bar (Spanneisen) 4000603053NW by AMF adheres to, ensuring compatibility with fixtures manufactured to the same specification. Which clamping screw size fits this fork-style clamping bar? The fork-style clamping bar is designed for an M24 clamping screw, matching the 26 mm slot profile to provide a secure connection. How does the 500 mm length affect workshop applications? The 500 mm overall length offers extended reach for larger workpieces, allowing clamping closer to the machining area and reducing the need for additional supports when using the AMF clamping bar. Is the fork-style clamping bar suitable for modular fixturing systems? Yes, the standardised DIN 6315B interface and common M24 compatibility make this bar well suited to modular fixturing concepts and standard workshop toolsets. What is included in the delivery for SKU 4000603053NW? Delivery consists of the clamping bar as a single unit (packaging unit: 1); additional clamping screws or fixture components are not included unless specified separately. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
500mm Fork Jaw Clamp DIN 6315B 22mm Slot For M20/M22 Screw - AMF
Take advantage of the fork‑type design, the 22 mm slot and the 500 mm overall length for stable, standardised clamping in fixture systems; order the component directly via Metav Werkzeuge or consult the Metav team for tailored selection and application advice. AMF Fork Clamping Bar DIN 6315B — Fork‑type clamping bar with 22 mm slot, 500 mm length The AMF Fork Clamping Bar DIN 6315B is a fork‑type clamping component for fixture and bench systems, designed to accept standard M20 and M22 clamping screws and to integrate with DIN‑compliant tooling. Fork‑type design for secure clamping 22 mm slot for standard mounting 500 mm overall length for extended reach Reliable clamping for precision fixtures The fork‑type geometry, specified to DIN 6315B, ensures a predictable engagement with clamping hardware and a secure clamping interface. The 22 mm slot provides a standard contact area that aligns with common fixture bars, enabling consistent force transfer when paired with M20 or M22 clamping screws. This standardisation reduces variability in repetitive setups and supports stable machining or assembly processes without the need for custom adapters. Fast integration with standard screw systems A 500 mm overall length combines reach with stable leverage, allowing integration across longer jaws and multiple clamping points. The length supports flexible positioning within a clamping layout and reduces the number of separate components required for extended fixtures. Compatibility with M20 and M22 thread sizes simplifies procurement and spare‑part management, contributing to reduced setup time and smoother changeovers between jobs. Practical workshop benefits and traceability Specification conformity and a clear SKU facilitate stock control and traceability in production environments. The clamping bar is listed under SKU 4000603051NW, supplied as a single unit, and marked for use in standardised systems. The fork execution offers a reliable mechanical interface for recurring fixturing tasks, supporting efficient workflows and predictable maintenance cycles while easing parts management in the workshop. For selection assistance or to secure this AMF fork clamping bar for specific fixtures, contact Metav Werkzeuge in Emmerich: info@metav-werkzeuge.com or call +49 2822 7131930 and request guidance from the Metav consultants. Technical data SKU: 4000603051NW Product type: Clamping bar (fork design) Standard: DIN 6315B Dimensions & compatibility Slot width: 22 mm Overall length: 500 mm Compatible with clamping screws: M20, M22 Features & applications Product category: Clamping bar Packaging unit: 1 Manufacturer: AMF FAQ What thread sizes are compatible with this clamping bar? The AMF fork clamping bar is compatible with M20 and M22 clamping screws, as stated in the technical specification. Does the bar conform to an industry standard? Yes, conformity to DIN 6315B is specified, which ensures interchangeability with other components designed to the same standard. What is the overall length and how does it affect fixturing? The overall length is 500 mm, providing extended reach for larger jaws or multiple clamping positions in a fixture layout. Can the SKU be used for stock and reorder purposes? SKU 4000603051NW is provided for ordering and inventory management to ensure correct identification and traceability. How is the product delivered in terms of packaging? The item is supplied as a single unit, with a packaging unit of 1 for straightforward handling and storage. Manufacturer: AMF; Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
60mm Clamping Wedge For 8mm T-Slot, For M8, DIN 6314 - AMF
Benefit from DIN 6314 conformity, 8 mm T‑slot compatibility and a compact 60 mm overall length for reliable, space‑efficient clamping; order the part via Metav Werkzeuge or ask the consultants for application advice. AMF clamping bar DIN 6314 for T‑slot 8 mm, L 60 mm The AMF clamping bar DIN 6314 is a compact clamping component for machine tables and fixture plates, engineered to engage 8 mm T‑slots and secure workpieces with M8 clamping screws. DIN 6314 compliant clamping component Fits 8 mm T‑slot profiles Compatible with M8 clamping screws Compact 60 mm overall length Reliable, standardised interface for predictable fixture assembly Compliance with DIN 6314 ensures a standardised interface that simplifies fixture planning and inventory management. The design is matched to an 8 mm T‑slot, meaning the clamp locates consistently in widely used machine table profiles; this reduces setup time and avoids trial‑and‑error fitting. Compatibility with M8 clamping screws permits use with common clamping hardware, allowing predictable clamping forces when paired with suitable bolts and washers. The result is a reproducible, auditable clamping solution for series or one‑off operations. Space‑efficient geometry that suits compact setups The compact geometry, with an overall length of 60 mm and a width of 9 mm, makes the clamp suitable where table real estate is limited. The reduced footprint enables multiple clamps to be positioned closely for short overhangs and confined machining zones, improving rigidity without sacrificing accessibility. Where minimal obstruction is required — for example in multi‑fixture nests or when using probing systems — the slim form factor supports efficient use of the working area while maintaining a secure hold. Practical data for workshop integration and planning Technical planners benefit from the documented addition values (Addition: A: 12; B2: 25; B3: 10; E1: 13; E2: 22), which support accurate alignment and accessory selection during fixture construction. Supplied as single units (packaging unit: 1), these clamps are straightforward to manage in small batches or mixed orders. For specific fixture designs or load cases, consult Metav Werkzeuge’s technical advisors who can assist with integration details and recommend matching clamping screws or complementary components to ensure a reliable system. Contact Metav Werkzeuge for tailored advice on using the AMF clamping bar DIN 6314 in precision fixture setups or to request delivery from our Emmerich stock. Technical Data Article number: 4000833001NW Product type: Clamping bar Brand: AMF Standard: DIN 6314 Facts Overall length: 60 mm Width: 9 mm T‑slot size: 8 mm Suitable for: M8 Special features Packaging unit: 1 Label: Spanneisen DIN 6314 f.T-Nut 8mm L.60mm AMF Addition: A: 12; B2: 25; B3: 10; E1: 13; E2: 22 FAQ Is the clamp suitable for standard metric T‑slots? The AMF clamping bar DIN 6314 is designed specifically for an 8 mm T‑slot and is compatible with M8 clamping screws used in standard metric fixtures. Does this component comply with an industrial standard? Yes, the clamp is manufactured to DIN 6314, guaranteeing a standardised interface for fixture tables and accessory compatibility. What are the exact dimensions to plan for? Overall length is 60 mm and width is 9 mm; the T‑slot engagement corresponds to an 8 mm slot and the clamp is intended for use with M8 screws. How is the product supplied for workshop use? The item is supplied in a packaging unit of 1, allowing selective procurement for single fixtures or staged additions to an existing setup. What do the addition values in the data mean for assembly? The listed addition values (A: 12; B2: 25; B3: 10; E1: 13; E2: 22) are provided to support alignment and accessory selection during fixture design and should be considered when positioning complementary components. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
60mm Fork Clamp Bar Slot 6.6mm For M6 Clamping Screw, DIN 6315B - AMF
Take advantage of the fork-style design and DIN compatibility for consistent, repeatable clamping in modular fixtures; the 6.6 mm slot and 60 mm length provide secure engagement with M6 tensioning screws. Order the clamp directly via Metav Werkzeuge or consult the team for application advice. AMF Fork Clamping Wedge, DIN 6315B – 6.6 mm Slot, 60 mm Length The AMF Fork Clamping Wedge is a DIN 6315B-compliant fork-style clamping element for use with M6 tensioning screws, ideal for compact and modular fixture setups. DIN 6315B fork-style clamping element Slot width 6.6 mm for precise engagement Length 60 mm for compact fixture setups Designed for M6 tensioning screws Consistent compatibility for modular fixturing The compliance with DIN 6315B guarantees standardised interfaces across modular clamping systems, reducing setup time and simplifying spare-part management. The fork-style geometry ensures reliable seatÂing in correspondingly prepared jaws and fixtures, so repeatability is improved in series production. For operations converting between suppliers or extending existing setups, the standard conformity provides predictable mechanical behaviour and interchangeability. Secure engagement in limited spaces With a 6.6 mm slot and 60 mm overall length, the component is designed for tight fixtures where axial space is limited. The fork configuration produces a defined contact surface that supports high clamping stability when paired with M6 tensioning screws — a common thread size in workshop clamps. This combination benefits setups that require compact elements without compromising the clamping force needed for machining or assembly tasks. Practical advantages for workshop use The fork clamping element offers a straightforward mechanical function that is easy to integrate into vises and modular plates. Its simple design minimises handling complexity and supports efficient changeovers during production. The clear specification of slot width and length aids in planning fixture layouts, while the DIN standard alignment helps procurement maintain consistent inventory and prevent mismatches. Contact Metav Werkzeuge today for precise ordering and application guidance — Metav’s workshop expertise ensures the right clamping solution for each setup. Technical Data Article number: 4000833020NW Product type: Clamping wedge Design: Fork design Standard: DIN 6315B Compatible with: M6 tensioning screws Slot width: 6.6 mm Overall length: 60 mm Manufacturer: AMF Packaging unit: 1 UID: 4000833020NW Core dimensions Slot width: 6.6 mm Overall length: 60 mm Compatible thread: M6 Packaging unit: 1 Special features Fork-style clamping element DIN 6315B compatibility Axite enrichment: A: 12; B2: 19; B3: 6; B4: 3 FAQ What applications suit this fork clamping wedge? The fork clamping wedge is suitable for modular fixture systems, machine vises and compact clamping assemblies where a DIN 6315B interface and an M6 tensioning screw are used. How does the DIN 6315B standard benefit workshop planning? DIN 6315B standardisation simplifies interchangeability and spare-part management; using the AMF fork clamping wedge with standard components reduces setup time and inventory complexity. Can the clamp be used with other thread sizes? This item is specified for use with M6 tensioning screws; adapting to different thread sizes requires matching wedges and screws conforming to the same DIN interface. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
80mm T-Nut Clamp Bar 10mm Slot DIN 6314, For M10 - AMF
Secure and repeatable clamping for machine tables is achieved with the combination of DIN 6314 standard compliance, compatibility with 10 mm T-slots, and an 80 mm overall length; these features support efficient set-ups and reliable fixture assembly. Order or consult Metav Werkzeuge for tailored supply and immediate availability. Clamping iron DIN 6314 for 10 mm T-slot, 80 mm – AMF A robust Clamping iron DIN 6314 intended for secure workholding in 10 mm T-slots on machine tables and fixtures DIN 6314 standardised design Fits 10 mm T-slots 80 mm effective clamping length Suitable for M10 fastening Consistent, standardised workholding for production use The DIN 6314 specification ensures a familiar, industrially accepted geometry that simplifies fixture design and interchangeability. The clamping iron offers an 80 mm overall length paired with an 11 mm flange width, providing a predictable contact area for securing components. Because the part is designed for a 10 mm T-slot, mechanical engineers and workshop technicians benefit from reduced set-up times and consistent clamping force across repeated operations, which supports higher throughput and fewer reworks. Straightforward compatibility with common fastening systems Designed to accept M10 fastenings, the component integrates seamlessly into existing clamping assemblies and retrofit projects. The standard thread compatibility removes the need for special adapters, while the T-slot geometry supports modular fixturing. For production planners, this means quicker tool changes and a reduction in bespoke parts inventory, enabling smoother transitions between jobs and better utilisation of machine time. Practical benefits for maintenance and workshop workflows The compact dimensions and standard form factor of this clamping element make inspection, replacement and layout planning uncomplicated. The predictable interface to 10 mm T-slots simplifies spare-part lists and eases procurement. In day-to-day repair or assembly tasks, the uniformity of parts like this AMF clamping iron helps maintain uptime, as technicians can rely on a known datum and clamping behaviour when positioning workpieces on the machine table. For reliable T-slot clamping with AMF quality and fast supply from Metav Werkzeuge, contact Metav Werkzeuge GmbH in Emmerich by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 to discuss availability and delivery options Technical data Article number: 4000833002NW Standard: DIN 6314 Description: Clamping iron for T-slot 10 mm, 80 mm, AMF Facts T-slot width: 10 mm Width: 11 mm Total length: 80 mm Suitable for: M10 Packaging unit: 1 Special features Label: Spanneisen DIN 6314 f.T-Nut 10mm L.80mm AMF Axite enrichment: A: 15; B2: 30; B3: 12; E1: 15; E2: 30 FAQ What T-slot size is this clamping iron intended for? The clamping iron is made for a 10 mm T-slot, matching standard table profiles that accept 10 mm slot widths and ensuring secure seating and repeatable fixturing. Which thread size should be used with this component? Use an M10 fastening for assembly; the geometry is specified to work with M10 bolts to ensure proper clamping force and compatibility. Does the component conform to any standard? Yes, the part is manufactured to DIN 6314, which defines the form and dimensions for this category of clamping element and supports interchangeability. Is this suitable for modular fixturing and repeat setups? The standardised shape and 80 mm length make the AMF clamping iron well suited to modular fixturing, helping to reduce set-up times and improve repeatability across production runs. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
8–32mm Clamp Bar T‑Slot 10mm With M10x10x80 Clamp Screw, Range 8–32mm - AMF
Combine 10 mm T‑slot compatibility with an adjustable clamping height of 8–32 mm to achieve stable, repeatable fixturing and faster set‑up times; order the AMF clamping bar directly via Metav Werkzeuge or consult their specialists for application-specific advice. AMF Clamping Bar Nr. 6314V — 10 mm T‑slot, clamping height 8–32 mm The AMF Clamping Bar Nr. 6314V is a compact clamping bar for 10 mm T‑slot workholding, offering an adjustable clamping height from 8 to 32 mm and supplied with an M10 clamping screw for immediate integration into standard fixtures Designed for 10 mm T‑slot Adjustable clamping height 8–32 mm Includes M10 x 10 x 80 clamping screw Compact width 11 mm for tight setups Secure, repeatable clamping for faster production changeovers Engineered for compatibility with standard 10 mm T‑slot fixtures, this clamping bar provides a defined clamping range of 8–32 mm, enabling consistent pressure across a variety of workpiece heights. The supplied M10 x 10 x 80 clamping screw simplifies assembly and reduces the need for additional components, which shortens set‑up times and lowers the risk of incorrect screw selection. The result is improved process reliability and reduced machine downtime through predictable, repeatable fixturing. Space-efficient dimensions that suit confined workstations The compact form factor is designed for situations where space is at a premium: with a width of 11 mm and an overall length of 80 mm, the component fits into tight fixturing arrangements without obstructing adjacent tooling. These measurable dimensions enable precise planning of fixture layouts and contribute to more efficient use of table real estate. The relatively short overall length also supports close‑packed clamping patterns, which can improve throughput on batch machining operations. Simple integration and transparent specification for procurement Delivered as a single‑unit package that includes the clamping screw, the component is ready for immediate installation into T‑nut rails and modular clamping setups. Clear, numeric specifications—such as the clamping height band, thread size and physical dimensions—facilitate technical comparison and procurement decisions, ensuring the bar aligns with existing clamping hardware. Documentation of key values supports compatibility checks and helps maintain traceability in production planning. Contact Metav Werkzeuge today for a technical match of the AMF clamping bar Nr. 6314V to specific fixturing requirements or to request detailed dimensional drawings from the Metav Werkzeuge team Technical data SKU: 4000833071NW Type: Nr. 6314V Product: Clamping bar (Spanneisen) Brand: AMF Packing unit: 1 Dimensions & core data T‑slot width: 10 mm Clamping height: 8–32 mm Width: 11 mm Overall length: 80 mm Thread: M10 A: 15 B2: 30 E1: 15 E2: 30 LS: 39 Included components & features Includes clamping screw M10 x 10 x 80 Suitable for T‑nut 10 mm Product type: Spanneisen FAQ Which T‑slot size is the clamping bar suited for? The clamping bar is designed for a 10 mm T‑slot and mates directly with T‑nut systems specified for that slot width. What is the adjustable clamping height range? Clamping height is adjustable between 8–32 mm, providing flexibility for different workpiece thicknesses. Is a clamping screw supplied with the unit? Yes, the AMF clamping bar Nr. 6314V is supplied with a clamping screw M10 x 10 x 80 as part of the standard delivery. What are the key external dimensions to consider when planning fixtures? Key dimensions are width 11 mm and overall length 80 mm; additional specification values include A: 15, B2: 30, E1: 15, E2: 30 and LS: 39. Is this clamping bar suitable for modular production fixtures? The design and specification values of the AMF clamping bar Nr. 6314V (SKU 4000833071NW) make it suitable for modular T‑slot fixturing and repetitive production clamping tasks Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com