WNMG 060402 T9225 Wendeplatten - Tungaloy
Benefit from a combination of CVD-coated carbide robustness, a trigon geometry with 0.2 mm corner radius and proven ISO compatibility for stable medium-to-heavy steel turning; order the insert directly via Metav Werkzeuge or consult our specialists for process matching. WNMG060402 T9225 turning insert — ISO WNMG 060402 for turning, Tungaloy WNMG060402 T9225 is an ISO-format turning insert designed for external and internal turning operations in medium-to-heavy steel machining. CVD-coated carbide grade T9225 Universal for medium to heavy steel Trigon shape with 0.2 mm corner radius Double-sided chipbreaker with cylindrical hole Increased productivity for challenging steel operations The combination of a CVD-coated carbide grade and a robust insert geometry delivers measurable gains in productivity during turning. The T9225 grade is formulated for mixed engagement conditions and lightly interrupted cuts, providing enhanced toughness compared with standard grades. This means fewer insert changes and longer tool life under variable cutting forces, supporting a reduced overall machining cost per component while maintaining consistent cycle times. Reliable clamping and ISO compatibility for predictable set-up Designed as an ISO-standard turning insert, the triangular format ensures clear seating and reproducible orientation in compatible holders. The trigon form with a nominal 80° included angle and a 0.2 mm corner radius gives a balance between edge strength and detail capability. Because compatibility depends on form, relief angle, tolerance class, fastening and thickness, choosing matched holders and clamping sets reduces setup time and prevents movement under load, improving positional repeatability and surface finish. Controlled chip formation and stable cutting behaviour The insert features a double-sided chipbreaker and a cylindrical locating hole that supports secure fastening. The chipbreaker geometry is tuned to the T9225 grade to assist in fragmenting and evacuating chips during continuous and slightly interrupted cuts, reducing the risk of entanglement and tool nose wear. For operators less familiar with chipbreaker function: it modifies the flow of swarf to limit heat concentration at the cutting edge, which helps preserve flank condition and contributes to predictable tool life. Practical application guidance and selection tips For best results in turning steel, match the WNMG060402 T9225 insert with a suitable outside holder or boring bar, a correct backing/clip set and replacement screws. Select cutting parameters that reflect workpiece rigidity and the intended surface finish; the tougher CVD-coated grade performs well under variable engagement but benefits from conservative feeds when finishing. For quieter, efficient shop-floor implementation, document the chosen holder, insert orientation and clamping torque to ensure repeatable outcomes across batches. For application-specific recommendations on Tungaloy CVD-coated inserts, contact Metav Werkzeuge for tailored advice and order support — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6787111 SKU: 6787111-Tungaloy Manufacturer SKU: TUN6787111 Facts Model series: ISO-Drehwendeschneidplatten Designation: WNMG060402 Size: 06 Thickness: 4.76 mm Special features Material: Hartmetall Grade: T9225 (CVD-coated) Shape: trigon Corner radius: 0.2 mm Relief angle: 0° Hole: with hole Hole style: cylindrical hole Chipbreaker: double-sided FAQ What materials is this insert suited for? The WNMG060402 T9225 insert is intended primarily for medium-to-heavy steel turning and performs well when cutting conditions require elevated toughness. How should the insert be clamped and oriented? Use an ISO-compatible triangular holder or boring bar designed for WNMG inserts; ensure the cylindrical locating hole and clip assembly are correct for secure clamping and repeatable alignment. Can this insert be used for interrupted cuts? Yes, the T9225 grade offers increased toughness for lightly interrupted cuts, making it suitable for variable engagement scenarios. How many cutting edges are available per indexable insert? The trigon, double-sided design provides multiple usable edges per insert; index and reorient the insert according to wear to maximise economy. Is the chipbreaker suitable for finishing operations? The double-sided chipbreaker supports controlled chip formation; for high-quality finishing, reduce feed and fine-tune speeds to match the desired surface finish. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
WNMG 060404 AH120 Wendeplatten - Tungaloy
Take advantage of the PVD-coated AH120 grade together with the trigon 06 geometry and 0.4 mm nose radius for reliable cutting performance and improved edge life in turning operations. Order the WNMG060404 AH120 Tungaloy insert directly via Metav Werkzeuge or ask the consultants for application guidance. WNMG 060404 AH120 — Tungaloy turning indexable insert for ISO WNMG060404 The WNMG060404 AH120 is an ISO-standard indexable turning insert designed for external and internal turning where a sharp cutting edge and high process reliability are required. PVD-coated carbide AH120 grade Trigon 06 form, 0.4 mm nose radius Double-sided chipbreaker design ISO-standard WNMG 060404 compatible Consistent cutting and extended edge life The AH120 grade is a PVD-coated carbide formulation engineered for both wear resistance and fracture protection, which directly improves tool life and reduces unplanned tool changes. The combination of a sharp cutting edge and a robust substrate delivers predictable performance in interrupted cuts and mixed material batches. For production environments that prioritise uptime, the process reliability delivered by this grade reduces scrap and supports consistent part quality, making it a practical choice for medium-duty turning tasks. Optimised geometry for flexible external and internal turning The trigon form and the 80° included angle give a compact cutting profile that balances strength and access. The trigon geometry with a 0.4 mm nose radius is suitable where a fine surface finish and dimensional control are required, while the 0° clearance produces a neutral cutting attitude that helps maintain edge stability on varying feed rates. A double-sided design and the cylindrical hole enable efficient indexation and straightforward positioning in ISO-compatible holders, so the insert adapts to both external and internal tool setups without complex adjustments. Simple integration and predictable chip control As an ISO-format insert, this component integrates into standard systems comprising the insert, a matching external holder or boring bar, a support/clamp set and replacement screws. The 4.76 mm thickness contributes to rigidity in the clamped assembly, while the double-sided chipbreaker promotes repeatable chip control for cleaner operation and easier chip evacuation. Selecting the appropriate chipbreaker and holder geometry according to material and stability will maximise the benefits of the AH120 grade and the WNMG060404 form, translating technical features into lower cycle-time variability and steadier surface quality. For reliable, repeatable turning with Tungaloy's AH120 grade, contact Metav Werkzeuge for availability and application advice — Metav Werkzeuge offers direct supply and technical consultation via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 6793709 SKU: 6793709-Tungaloy Manufacturer SKU: TUN6793709 Model series: ISO turning indexable inserts Designation: WNMG060404 AH120 Manufacturer: Tungaloy Facts Included angle: 80° Size: 06 Thickness: 4.76 mm Nose radius: 0.4 mm Clearance angle: 0° Hole: cylindrical Special features Shape: trigon, double-sided Grade/coating: AH120, PVD-coated carbide Chipbreaker: double-sided Application: external and internal turning Compatibility: ISO WNMG 060404 holders by form, clearance, tolerance, clamping System: insert, suitable external holder/boring bar, support/clamp set, replacement screws FAQ Which materials is this insert suitable for? The WNMG060404 AH120 insert is formulated for a broad range of turning tasks where wear resistance and edge stability are needed; the AH120 grade excels in machining many steels and mixed batches requiring process security. Is this insert suitable for finishing passes? Yes — with a 0.4 mm nose radius and a sharp PVD-coated edge, the insert supports fine surface finishes when combined with appropriate feeds and speeds and a stable holder assembly. How does the AH120 grade differ from tougher grades? AH120 focuses on a balance of wear resistance and fracture protection, offering a sharper effective edge and consistent performance under varying cutting conditions compared with very hard, more brittle grades. What does the 0° clearance angle mean in practice? A 0° clearance produces a neutral cutting orientation that can improve edge life in interrupted cuts and help maintain consistent tool contact; selection of holder geometry and cutting parameters remains important to avoid rubbing. How is the insert indexed and secured in the holder? The WNMG060404 design is double-sided with a cylindrical hole for secure clamping; correct torque and a compatible clamping set ensure repeatable seating and reliable cutting performance. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
WNMG 060404 AH120 Wendeplatten - Tungaloy
WNMG 060404 AH120 Wendeplatte für Drehen, Tungaloy Die WNMG 060404 AH120 ist eine ISO-genormte Drehwendeschneidplatte aus PVD-beschichtetem Hartmetall, entwickelt für wirtschaftliche und prozesssichere Außen‑ und Innendreh‑Anwendungen. WNMG 060404 AH120 Tungaloy Wendeplatte PVD-beschichtetes Hartmetall für stabile Standzeit Trigonform (80°) für sichere Halterkompatibilität Eckenradius 0,4 mm für feine Schnittqualität Zylindrisches Loch, doppelseitiger Spanbrecher Zuverlässige Standzeit und höhere Prozesssicherheit Dank des PVD-beschichteten Hartmetalls der Sorte AH120 bietet die Platte eine hohe Verschleißfestigkeit und reduziert das Risiko von Ausbrüchen an der Schneide. Das Ergebnis ist eine längere Standzeit und geringere Stillstandszeiten in der Produktion, was besonders in Serienfertigung und Lohnfertigung die Wirtschaftlichkeit verbessert. Die robuste Beschichtung sorgt für konstante Schneidkantenstabilität auch bei wechselnden Schnittbedingungen. Präzise Schneidkante und vielseitige Einsatzmöglichkeiten beim Drehen Die WNMG 060404 AH120 kombiniert die Trigonform mit einem Spanwinkel von 80° und einem Eckenradius 0,4 mm, wodurch feine Oberflächen und reproduzierbare Konturen erzielt werden. Die Platte eignet sich für Außen‑ und Innendrehen; durch den doppelseitigen Spanbrecher stehen zwei Schneiden zur Verfügung, was den Werkzeugwechselintervall verlängert und die Kosten pro Bauteil senkt. ISO‑Normierung gewährleistet einfache Auswahl passender Halter. Einfache Integration in Haltersysteme und praktisches Handling Die Wendeplatte besitzt ein zylindrisches Loch zur sicheren Befestigung und eine Plattendicke von 4,76 mm, was die Kompatibilität mit gängigen Außenhaltern und Bohrstangen erhöht. Anwender profitieren von klarer Zuordnung nach ISO‑Maßen, einfacher Lagerhaltung und schnellen Wechselzyklen. Bei speziellen Werkstoffen oder Schnittdaten hilft die gezielte Auswahl des Spanbrechers und der Sorte, das optimale Ergebnis zu erzielen. Für prozessorientierte Fertiger empfiehlt Tungaloy die WNMG 060404 AH120 als wirtschaftliche Lösung für präzises Drehen – Technische Beratung und Bestellung über Metav Werkzeuge: info@metav-werkzeuge.com, +49 2822 7131930 Produktmerkmale Bezeichnung: WNMG060404 AH120 Artikelnummer: 6793712 Marke: Tungaloy Serie: ISO-Drehwendeschneidplatten Hersteller SKU: TUN6793712 Fakten Eckenradius: 0,4 mm Plattendicke: 4,76 mm Winkel: 80° Freiwinkel: 0° Plattengröße: 06 Besonderheiten Schneidstofftyp: PVD-beschichtetes Hartmetall Sorte: AH120 Plattenform: Trigon Loch: mit Loch (zylindrisches Loch) Spanbrecher: doppelseitig Anwendung: Drehen ISO-Bezeichnung: WNMG060404 FAQ Was unterscheidet die WNMG 060404 AH120 von anderen Wendeplatten? Die WNMG 060404 AH120 von Tungaloy kombiniert eine PVD‑Beschichtung mit einer verschleißfesten Hartmetallsorte, was zu höherer Standzeit und verbesserter Prozesssicherheit führt; die Trigonform und der Eckenradius 0,4 mm optimieren die Oberflächenqualität. Für welche Drehanwendungen eignet sich diese Wendeplatte am besten? Die Platte ist für Außen‑ und Innendrehen ausgelegt; durch die ISO‑Normierung und die Trigonform ist die WNMG 060404 AH120 besonders geeignet für Serienfertigung und wechselnde Einspannbedingungen. Wie profitiert die Produktion von der Sorte AH120? Die AH120‑Sorte bietet stabile Spanbildung und gute Ausbruchsresistenz. Das reduziert Werkzeugwechsel und führt zu konstanteren Fertigungsergebnissen sowie niedrigeren Stückkosten. Ist die WNMG 060404 AH120 mit Standardhaltern kompatibel? Ja, die ISO‑Genormung und das zylindrische Loch ermöglichen einfache Integration in gängige Außenhalter und Bohrstangen; die Plattendicke 4,76 mm und der Spanwinkel 80° sind gängige Werte für universelle Einsatzmöglichkeiten. Welche Angaben helfen bei der Bestellvorbereitung? Für eine präzise Bestellung geben Sie Bezeichnung, Marke und Artikelnummer an: WNMG060404 AH120, Tungaloy, Artikelnummer 6793712. Das vereinfacht die Zuordnung und Lagertechnik. Hersteller: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
WNMG 060404 AH6225 Wendeplatten - Tungaloy
WNMG 060404 AH6225 Wendeplatte – Drehen · Tungaloy Der WNMG 060404 AH6225 Wendeplatte ist eine ISO-genormte Drehwendeschneidplatte für Außen- und Innendrehen, entwickelt für den Einsatz bei rostfreien Stählen und mittleren Bearbeitungsbedingungen ISO-genormte Trigon-Form mit zylindrischem Loch PVD-beschichtetes Hartmetall für stabile Schneidkante Speziell ausgelegt für rostfreie Stähle Eckenradius 0,4 mm für feine Kontur-Definition Plattendicke 4,76 mm, Freiwinkel 0° Hervorragende Standzeit durch Beschichtung und Grundstoff Die Kombination aus Hartmetall-Substrat und PVD-beschichtung sorgt für eine dauerhaft scharfe Schneidkante bei wechselnden Schnittbedingungen. Durch die dünne, harte Beschichtung reduziert sich der Verschleiß an der Schneidkante, was längere Nutzzeiten ermöglicht und Rüstzyklen reduziert. Anwender profitieren von gleichbleibender Teilequalität und geringerer Nacharbeit. Präzise Spanformung und Werkstoffanpassung für rostfreie Stähle Für die Bearbeitung von rostfreien Stählen bietet die Sorte AH6225 ein ausgewogenes Verhältnis zwischen Schärfe und Stabilität der Schneidkante. Die Platte ist mit einem doppelseitigen Spanbrecher versehen, der konstante Spanbildung unterstützt und dadurch die Oberflächengüte verbessert. So lassen sich reproduzierbare Ergebnisse auch bei wechselnden Schnittparametern erzielen. Kompatibilität, Aufbau und praktische Vorteile im Fertigungsalltag Die ISO-Drehwendeschneidplatte ist auf Kompatibilität mit gängigen Außenhaltern und Bohrstangen ausgelegt; Form, Freiwinkel, Befestigung und Dicke bestimmen die Passung zum Halter. Die trigonale Form mit zylindrischem Loch ermöglicht sicheren Sitz und einfache Indexierung. Für Werkstätten bedeutet das weniger Umrüstaufwand und höhere Maschinenverfügbarkeit. Zielgruppe und Einsatzempfehlung Die Platte richtet sich an Fertiger und Instandhalter, die häufig rostfreie Stähle bearbeiten und Wert auf Prozessstabilität legen. Durch die mittlere Leistungscharakteristik eignet sich das Produkt für Serien mit moderaten Schnittwerten sowie für flexible Kleinserien in der Feinmechanik und im Maschinenbau. Empfehlung: Für produktive Drehprozesse die WNMG 060404 AH6225 Wendeplatte von Tungaloy einsetzen und bei Bedarf technische Beratung bei Metav Werkzeuge anfragen – eMail: info@metav-werkzeuge.com, Telefon: +49 2822 7131930 Produktspezifikationen Artikelnummer: 6947514 Marke: Tungaloy Serie: ISO-Drehwendeschneidplatten SKU: TUN6947514 Fakten Eckenradius: 0,4 mm Plattendicke: 4,76 mm Winkel: 80° Freiwinkel: 0° Plattengröße: 06 Loch: mit Loch Lochstil: zylindrisches Loch Besonderheiten Material: Hartmetall Sorte: AH6225 – universelle Sorte für rostfreie Stähle, scharfe und stabile Schneidkante Schneidstofftyp: PVD-beschichtetes Hartmetall (PVD: Physical Vapour Deposition, dünne Hartstoffschicht) Plattenform: Trigon Spanbrecher: doppelseitig Systemaufbau: ISO-Drehplatte, passender Außenhalter oder Bohrstange, Unterlage/Klemmsatz, Ersatzschrauben FAQ Welche Werkstoffe sind für die WNMG 060404 AH6225 Wendeplatte geeignet? Die WNMG 060404 AH6225 Wendeplatte von Tungaloy ist speziell für rostfreie Stähle ausgelegt und liefert in diesem Werkstoffspektrum stabile Schneidkanten und gute Oberflächengüten. Wie beeinflusst der Eckenradius die Bearbeitungsergebnisse? Ein Eckenradius von 0,4 mm ermöglicht feine Kontur-Definition und reduziert Schneidkantenbeanspruchung, wodurch die WNMG 060404 AH6225 Wendeplatte saubere Schnittkanten bei mittleren Schnittbedingungen erzeugt. Ist die Platte für Innen- und Außendrehen gleichermaßen geeignet? Ja, die ISO-Genorm und die trigonale Form machen die WNMG 060404 AH6225 Wendeplatte kompatibel für Außen- und Innendrehanwendungen in passenden Haltern. Welche Vorteile bietet die PVD-Beschichtung bei dieser Wendeplatte? Die PVD-Beschichtung erhöht die Verschleißfestigkeit der Schneidkante und verbessert die Standzeit, sodass mit der WNMG 060404 AH6225 Wendeplatte längere Bearbeitungsintervalle und konstantere Ergebnisse möglich sind. Wie wird die Kompatibilität zum Halter geprüft? Die Kompatibilität ergibt sich aus Form, Freiwinkel, Toleranzklasse, Befestigung, Größe und Dicke; bei Unsicherheiten sollten die Halterdaten mit den Spezifikationen der WNMG 060404 AH6225 Wendeplatte abgeglichen werden. Hersteller: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
WNMG 060404 AH6225 Wendeplatten - Tungaloy
WNMG 060404 AH6225 — Wendeplatte zum Drehen von Tungaloy WNMG 060404 AH6225 ist eine ISO-genormte Trigon-Wendeplatte für präzises Außen- und Innendrehen, speziell ausgelegt für die Bearbeitung von rostfreien Stählen. Trigon-Wendeplatte, ISO-Größe 06 PVD-beschichtetes Hartmetall für rostfreie Stähle Doppelseitiger Spanbrecher für stabile Spanbildung Mit zylindrischem Loch für sichere Befestigung Eckenradius 0,4 mm für feine Konturentragen Robuste Schneidkante und Beschichtung für mittlere Bearbeitung Die WNMG060404 AH6225 kombiniert Hartmetall-Substrat mit einer PVD-beschichtung, die Verschleiß reduziert und eine scharfe, zugleich stabile Schneidkante sichert. Diese Kombination erhöht die Prozesssicherheit bei wechselnden Schnittbedingungen und sorgt für konstante Standzeit. Die PVD-Technologie verbessert die Haftfestigkeit der Schicht und minimiert Ausbrüche bei rostfreien Werkstoffen, wodurch die Nacharbeit reduziert wird. ISO-Kompatibilität und einfache Integration in Werkzeugpartner-Systeme Dank ISO-genormter Form und Abmessungen lässt sich die Wendeplatte in viele gängige Haltersysteme integrieren. Die Kompatibilität hängt von Form, Freiwinkel, Toleranzklasse, Befestigung, Größe und Dicke ab; deshalb empfiehlt sich die Prüfung anhand von Halterdatenblatt und Maschinenaufbau. Die Trigon-Form ermöglicht vielseitigen Einsatz beim Außen- und Innendrehen und vereinfacht den Wechsel zwischen unterschiedlichen Haltern. Wirtschaftlichkeit durch doppelseitigen Spanbrecher und präzisen Radius Der doppelseitige Spanbrecher erhöht die Ausnutzbarkeit der Platte und senkt die Stückkosten, weil beide Schneidkanten nutzbar sind. Der Eckenradius von 0,4 mm liefert eine reproduzierbare Kantengestalt für gute Oberflächengüte bei mittleren Schnitten. Anwender profitieren von stabiler Spanbildung und zuverlässig reproduzierbaren Ergebnissen bei Serienfertigung und Einzelteilbearbeitung. Empfehlung: Die WNMG060404 AH6225 von Tungaloy für zuverlässige Bearbeitung rostfreier Stähle direkt bei Metav Werkzeuge anfragen — bei technischen Fragen per eMail: info@metav-werkzeuge.com oder Telefon: +49 2822 7131930 Produktmerkmale Artikelnummer: 6947526 Hersteller: Tungaloy Modellserie: ISO-Drehwendeschneidplatten Bezeichnung: WNMG060404 AH6225 SKU: TUN6947526 Daten Winkel: 80° Freiwinkel: 0° Eckenradius: 0,4 mm Plattendicke: 4,76 mm Plattengröße: 06 Besonderheiten Material: Hartmetall Beschichtung: PVD-beschichtet Plattenform: trigon Loch: mit Loch (zylindrisches Loch) Spanbrecher: doppelseitig Schneidstoffsorte: AH6225 Schneidstofftyp: PVD-beschichtetes Hartmetall Anwendung: Drehen Einsatzbereich: rostfreier Stahl FAQ Für welche Werkstoffe ist die Wendeplatte geeignet? Die WNMG060404 AH6225 von Tungaloy ist primär für die Bearbeitung von rostfreiem Stahl konzipiert; durch die universelle Sorte AH6225 ist sie zudem für wechselnde Schnittbedingungen geeignet. Wie wird die Kompatibilität zum Halter geprüft? Kompatibilität richtet sich nach Form, Freiwinkel, Toleranzklasse, Befestigungsart, Größe und Dicke; die ISO-genormte Bezeichnung WNMG060404 erleichtert die Zuordnung zu passenden Außenhaltern und Bohrstangen. Welche Vorteile bietet die PVD-Beschichtung der AH6225-Sorte? Die PVD-beschichtung erhöht die Verschleißfestigkeit und reduziert Ausbruchneigung, wodurch die Wendeplatte längere Standzeiten und konstantere Oberfläche bei rostfreien Stählen liefert. Warum ist der doppelseitige Spanbrecher praktisch? Ein doppelseitiger Spanbrecher bietet ökonomische Vorteile, da beide Schneidkanten genutzt werden können, und verbessert die Spanformung für stabile Fertigungsprozesse. Sind spezielle Schnittdaten hinterlegt? Schnittdaten hängen von Werkstoff, Maschinensteifigkeit, Kühlung und Halterausführung ab; die WNMG060404 AH6225 ist für mittlere Bearbeitung ausgelegt und erfüllt universelle Anforderungen bei variierenden Bedingungen. Hersteller: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
WNMG 060404 AH6225 Wendeplatten - Tungaloy
WNMG 060404 AH6225 Wendeplatte zum Drehen — Tungaloy WNMG060404 AH6225 ist eine ISO-genormte Trigon-Wendeplatte für das präzise Außen- und Innendrehen mit universeller Eignung für rostfreie Stähle Trigonform mit 0,4 mm Eckenradius PVD-beschichtetes Hartmetall für mittlere Schnitte Doppelseitiger Spanbrecher für stabile Spanbildung Mit zylindrischem Loch und 4,76 mm Plattendicke Hohe Standzeit durch Material und Beschichtung Die Kombination aus Hartmetall und PVD-Beschichtung sorgt für eine langlebige und belastbare Schneidkante, die besonders bei wechselnden Schnittbedingungen überzeugt. Durch die harte Beschichtung wird die Wärmeaufnahme reduziert, was die Standzeit erhöht und Stillstandszeiten in der Fertigung verringert. Kunden profitieren so von konstanteren Bearbeitungsergebnissen und geringeren Werkzeugwechseln. Präzision und Stabilität im Drehprozess Die Trigon-Plattenform mit 0,4 mm Eckenradius bietet eine präzise Kantenführung bei standardisierten Haltern und Bohrstangen. Die Wendeplatte ist für das Außen- und Innendrehen ausgelegt und liefert eine stabile Schneidkante auch bei mittleren Schnittparametern. Das doppelseitige Design erlaubt zwei Nutzseiten und erhöht die Wirtschaftlichkeit pro Platte. Kompatibilität und Aufbau für effiziente Prozesse Die Kompatibilität zur Werkzeugaufnahme ergibt sich aus Form, Freiwinkel, Toleranzklasse, Befestigung, Größe und Dicke. Die WNMG060404 AH6225 fügt sich in ISO-konforme Systeme ein und benötigt lediglich passenden Außenhalter, Unterlage und Befestigungsschraube. Diese Systemnähe erleichtert die Integration in vorhandene Bearbeitungszellen und reduziert Einrichtzeiten. Einsatzgebiet und Werkstoffabdeckung Die Sorte AH6225 wurde speziell als universelle Lösung für rostfreie Stähle entwickelt, mit einer scharfen, zugleich stabilen Schneidkante für wechselnde Bedingungen. Durch optimierte Spanformer und die Materialauslegung eignet sich die Platte für Anwender, die eine zuverlässige Bearbeitung mit guter Oberflächengüte erwarten. Setzen Sie auf die AH6225-Sorte von Tungaloy für eine wirtschaftliche und zuverlässige Zerspanung — bestellen Sie über Metav Werkzeuge oder kontaktieren Sie unsere Beratung per eMail: info@metav-werkzeuge.com oder Telefon: +49 2822 7131930 Technische Daten Artikelnummer: 6903240 Marke: Tungaloy Serie: ISO-Drehwendeschneidplatten Bezeichnung: WNMG060404 AH6225 Tungaloy-Wendeplatte Fakten Winkel: 80° Freiwinkel: 0° Eckenradius: 0,4 mm Plattendicke: 4,76 mm Plattengröße: 06 Besonderheiten Material: Hartmetall Beschichtung: PVD Sorte: AH6225 Plattenform: Trigon Spanbrecher: doppelseitig Loch: mit Loch (zylindrisches Loch) Anwendung: Drehen Typische Anwendung: Außen- und Innendrehen FAQ Welche Werkstoffe sind für diese Wendeplatte geeignet? Die WNMG060404 AH6225 von Tungaloy ist speziell für rostfreie Stähle ausgelegt; die AH6225-Sorte bietet gute Spanbildung und stabile Schneidkanten bei mittleren Schnittbedingungen. Wie lässt sich die Platte in bestehende Haltersysteme einbauen? Die ISO-Genormung der Wendeplatte gewährleistet Kompatibilität zu entsprechenden Außenhaltern und Bohrstangen, wobei Form, Freiwinkel und Befestigung die Passgenauigkeit bestimmen. Was macht die AH6225-Beschichtung besonders? Die PVD-Beschichtung reduziert Wärmeeintrag und Verschleiß, erhöht die Standzeit und verbessert die Prozessstabilität bei variierenden Schnittbedingungen. Lässt sich die Platte für Innen- und Außenbearbeitung verwenden? Ja, die WNMG060404 ist für Außen- und Innendrehen geeignet und liefert bei beiden Anwendungen eine konstante Oberflächengüte. Hersteller: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
WNMG 060404 AH6225 Wendeplatten - Tungaloy
Take advantage of the combination of a sharp, stable cutting edge and universal material compatibility to keep turning operations productive; the PVD-coated AH6225 grade and ISO trigon form ensure consistent results in varied conditions. Order directly via Metav Werkzeuge or consult the technical team for application-specific recommendations. WNMG 060404 AH6225 indexable insert for turning — Tungaloy, PVD-coated carbide, 0.4 mm radius A WNMG060404 AH6225 indexable insert designed for ISO-compliant external and internal turning, optimised for rostfreier Stahl and medium-duty machining PVD-coated carbide AH6225 Optimised for rostfreier Stahl 0.4 mm nose radius, 80° geometry Double-sided chipbreaker, trigon form Consistent edge performance for reliable turning results The PVD-coated AH6225 grade combines a PVD-coated carbide substrate with a geometry tuned for rostfreier Stahl, delivering a sharp yet robust cutting edge. This balance reduces the frequency of edge chipping during interrupted cuts and variable conditions, contributing to longer effective tool life and fewer changeovers. The coating improves wear resistance and heat management at the cutting zone, while the substrate maintains structural integrity under moderate depths of cut. For workshops seeking steady production, these properties translate into lower process variability and improved surface finishes on turned components. Geometry and chip control that support productivity The trigon form with an 80° inclusion angle and 0.4 mm nose radius provides a versatile contact geometry suitable for a wide range of turning tasks. A double-sided chipbreaker supports predictable chip formation and evacuation, particularly when paired with the correct feed and cutting speed for the workpiece material. The insert’s 4.76 mm thickness and the presence of a cylindrical hole ensure secure clamping in compatible holders, increasing rigidity and thereby reducing vibration. These design choices help to maintain dimensional accuracy and surface quality while enabling efficient material removal in daily workshop use. System compatibility and practical handling advice This ISO-series insert fits into a standard system comprising a matching external holder or boring bar, a shim or clamping set and replacement screws. Compatibility depends on the insert’s form, free angle (0°), tolerance class, method of fixation, size and thickness; these parameters should be verified against the chosen toolholder to ensure correct seating and secure retention. Select the chipbreaker and grade according to the component material and the machine–workpiece stability: a tighter setup benefits from the sharper edge for fine finishing, whereas less stable setups benefit from slightly more conservative cutting data to protect the edge. For reliable turning of rostfreier Stahl with extended edge life, order the WNMG060404 AH6225 indexable insert from Metav Werkzeuge or contact Metav Werkzeuge’s consultants for tailored machining advice at info@metav-werkzeuge.com or +49 2822 7131930 Product data Article number: 6947561 Manufacturer SKU: TUN6947561 SKU: 6947561-Tungaloy Dimensions & core data Nose radius: 0.4 mm Inclusion angle: 80° Plate thickness: 4.76 mm ISO designation: 060404 Plate size: 06 Design & features Material: Hartmetall (carbide) Grade/coating: AH6225 (PVD-coated) Plate form: trigon Chipbreaker: double-sided Mounting: with cylindrical hole Typical application: Drehen (turning) Model series: ISO-Drehwendeschneidplatten FAQ What materials is this insert suited for? The WNMG060404 AH6225 insert is formulated as a universal grade for rostfreier Stahl and performs well across a broad range of stainless applications when matched with appropriate cutting data. How does the AH6225 coating benefit machining? The PVD AH6225 coating increases wear resistance and thermal stability, enabling steadier cutting performance and longer edge life on rostfreier Stahl during medium machining tasks. Which holders are compatible with this ISO insert? Compatibility depends on holder geometry and clamping design; the insert requires a holder that accepts ISO-format trigon inserts with a cylindrical hole and supports a 4.76 mm plate thickness. Can this insert be used for internal turning as well as external turning? Yes, the ISO-series design supports both external and internal turning operations provided the chosen holder and set-up ensure sufficient rigidity. What advantage does the 0.4 mm nose radius offer? A 0.4 mm nose radius balances edge strength and surface finish capability, offering reliable profile control while resisting chipping in typical production feeds. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
WNMG 060404 AH6225 Wendeplatten - Tungaloy
Benefit from the combination of a PVD-coated carbide AH6225 grade, a sharp yet stable cutting edge, and ISO-standard geometry for reliable turning — order directly via Metav Werkzeuge or consult our technical advisors if further specification is required. WNMG060404 AH6225 — WNMG ISO turning insert for turning, PVD-coated carbide (Tungaloy) The WNMG060404 AH6225 is an ISO-standard indexable turning insert designed for external and internal turning of stainless steels, offering a balanced mix of sharpness and edge stability for medium machining and variable conditions. ISO-standard WNMG geometry PVD-coated carbide AH6225 grade Double-sided trigon insert Cylindrical hole for secure clamping Optimised cutting performance for stainless steels The AH6225 grade is a PVD-coated carbide developed as a universal solution for stainless steels, combining a finely honed cutting edge with substrate toughness. This balance reduces built-up edge and improves surface finish during medium machining. The trigon geometry and the specified corner radius support stable chip formation under changing cutting conditions, which helps maintain consistent dimensional accuracy and reduces the frequency of tool changes. Where surface integrity and repeatable component quality matter, the combination of coating and substrate offers measurable improvements in process reliability. ISO compatibility and secure clamping for reduced setup time Compatibility is determined by the ISO geometry and key holder parameters such as form, relief angle, tolerance class, clamping method, size and thickness. The trigon shape and cylindrical hole ensure positive location and repeatable seating in matching holders or boring bars. A correct system setup — indexable insert, matching external holder or boring bar, shim/clamping set and spare screws — simplifies changeovers and minimises downtime. The standardised form supports a wide range of holders across suppliers, enabling quick replacement and predictable assembly in mixed production environments. Lower tooling cost per part and predictable tool life A double-sided trigon insert allows multiple indexings, extending service life and reducing tooling cost per cutting edge. The AH6225 grade delivers a robust cutting edge that tolerates intermittent interruptions and variable feeds common in batch production. The integrated chipbreaker design assists controlled chip evacuation during turning, which improves operator safety and reduces secondary operations. The result is enhanced productivity with fewer unexpected interventions and more consistent component throughput. Faster selection and targeted application guidance Designed primarily for external and internal turning operations at medium cutting intensities, the insert performs best when the chipbreaker and grade are selected to match workpiece material and machine–workpiece stability. Where process stability is limited, choose a more conservative feed and a chipbreaker suited to secure swarf control. For higher-volume runs, the robust PVD coating and substrate combination contribute to steady wear behaviour and reproducible results across batches. For specific combinations of holder, feed and depth of cut, reference the ISO geometry and the insert’s dimensional data when planning tool lists. Contact Metav Werkzeuge for tailored application advice on Tungaloy turning inserts such as the WNMG060404 AH6225 and availability details; email info@metav-werkzeuge.com or call +49 2822 7131930 for fast, informed assistance. Technical data Article number: 6947535 Manufacturer SKU: TUN6947535 SKU: 6947535-Tungaloy Model series: ISO-Drehwendeschneidplatten Manufacturer: Tungaloy Facts Cutting angle: 80° Corner radius: 0.4 mm Thickness: 4.76 mm Insert size: 06 Relief angle: 0° Special features Grade/coating: AH6225 (PVD-coated carbide) Insert shape: trigon Chipbreaker: double-sided Hole: with cylindrical hole Application: turning System: ISO insert — compatible holders, shim/clamping set and spare screws FAQ Is this insert suitable for stainless steels? Yes. The AH6225 grade on the WNMG060404 AH6225 insert is specified as a universal grade for stainless steels, offering a combination of cutting edge sharpness and stability for medium turning operations. Can the insert be used for internal turning as well as external turning? Yes. The ISO geometry and trigon shape permit both external and internal turning; selection of the appropriate holder and cutting parameters ensures optimal performance with the WNMG060404 AH6225 insert. What determines compatibility with holders? Compatibility is defined by the ISO form, relief (relief angle), tolerance class, clamping method, size and thickness. Matching these parameters ensures secure seating of the WNMG060404 AH6225 insert in the chosen holder. What coating and substrate does the insert use? The insert is a PVD-coated carbide grade (AH6225), combining a wear-resistant coating with a tough carbide substrate for reliable edge life in varied conditions. How does the chipbreaker design affect machining? The double-sided chipbreaker promotes controlled chip formation and evacuation during turning, supporting stable cutting and improved surface quality with the WNMG060404 AH6225 insert. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
WNMG 060404 AH6235 Wendeplatten - Tungaloy
Take advantage of the PVD-coated AH6235 grade and the trigon geometry to machine rostfreier Stahl reliably, even under interrupted cuts; compatibility with ISO holders ensures straightforward replacement and consistent clamping. Order this insert via Metav Werkzeuge or consult our specialists for application-specific recommendations. WNMG 060404 AH6235 — Tungaloy turning insert, PVD-coated carbide for rostfreier Stahl WNMG060404 AH6235 is an ISO-format trigon insert for external and internal turning, designed for applications with increased breakout risk and interrupted cuts PVD-coated carbide AH6235 Optimised for rostfreier Stahl Trigon shape, 80° cutting angle Double-sided chipbreaker, with cylindrical hole Reliable cutting performance for challenging rostfreier Stahl applications The WNMG060404 AH6235 insert combines a PVD-coated surface with a tough carbide substrate to resist chipping during interrupted cuts and to maintain edge integrity when machining rostfreier Stahl. The AH6235 grade is tuned for tougher materials: the coating reduces friction and improves heat resistance, while the substrate provides the fracture toughness needed where chip formation is unstable. This results in more consistent component quality and fewer unplanned tool changes, supporting higher uptime and predictable cycle times. Geometry and mounting that simplify set-up and repeatability The trigonal plate form with an 80° approach angle and a 0° clearance provides a stable cutting geometry that suits many ISO holders. The cylindrical hole and standard sizing ensure compatibility determined by form, clearance, tolerance class, attachment method, size and thickness; this makes the insert straightforward to index and replace in production. The trigon geometry gives multiple cutting edges per plate, reducing handling and increasing tool life per index, while maintaining a consistent cutting line for repeatable surface finishes. Process reliability, economy and material-specific control With a double-sided chipbreaker and the robust AH6235 grade, this insert offers balanced chip control and predictable wear behaviour. The result is lower cost per cutting edge and stable surface integrity on parts where breakout or built-up edge might otherwise compromise tolerances. Specifying a suited chipbreaker and grade for the workpiece and machining conditions translates into fewer rejects and a more economical production flow. For application planning or if machining parameters are uncertain, technical consultation helps select the optimal holder, feed and speed to match the task. Contact Metav Werkzeuge for tailored advice on Tungaloy inserts and specify WNMG060404 AH6235 for rostfreier Stahl applications — email info@metav-werkzeuge.com or phone +49 2822 7131930 for application support and availability Technical data Article number: 6903426 SKU: 6903426-Tungaloy Manufacturer SKU: TUN6903426 Brand: Tungaloy Model series: ISO-Drehwendeschneidplatten Material: Carbide (Hartmetall) Facts Corner radius: 0.4 mm Cutting angle: 80° Plate thickness: 4.76 mm Size: 06 Clearance angle: 0° Hole: with cylindrical hole Special features PVD-coated carbide AH6235 Suited for rostfreier Stahl and interrupted cuts Trigon plate form (WNMG) Double-sided chipbreaker ISO-compatible for turning With cylindrical hole for positive clamping FAQ What materials is this insert suitable for? The WNMG060404 AH6235 insert is specified for machining rostfreier Stahl and other demanding materials where increased fracture toughness and chip control are required. Can this insert be used for interrupted cuts? Yes, the AH6235 grade and the insert geometry are designed to tolerate interrupted cutting conditions and applications with elevated breakout risk. How is the insert mounted and indexed? The trigonal plate is secured via its cylindrical hole and compatible ISO holders; compatibility depends on form, clearance, tolerance class, attachment and plate thickness. What benefits does the PVD coating bring? The PVD-coated surface reduces friction and enhances heat resistance, improving tool life and surface consistency when machining tougher materials with potential built-up edge. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
WNMG 060404 AH8015 Wendeplatten - Tungaloy
WNMG 060404 AH8015 Wendeplatte für Drehen — Tungaloy Die WNMG 060404 AH8015 Wendeplatte ist eine ISO-genormte Trigon-Wendeplatte, ausgelegt für das Außen- und Innendrehen hitzebeständiger Legierungen und seriennahe Zerspanungsprozesse. Trigonform für stabile Halterauflage PVD-beschichtetes Hartmetall AH8015 Eckenradius 0,4 mm für präzise Kanten Plattendicke 4,76 mm, ISO-genormt Mit zylindrischem Loch und doppelseitigem Spanbrecher Höhere Standzeit bei hitzebeständigen Werkstoffen Die Kombination aus PVD-Beschichtung und ausgewogener Hartmetallmatrix macht diese Wendeplatte zur ersten Wahl für die Bearbeitung hitzebeständiger Legierungen. Anwender profitieren von verbesserter Verschleißfestigkeit und stabiler Schneidkante, was längere Standzeiten und konstantere Oberflächengüten in der Serienfertigung ermöglicht. Dadurch reduzieren sich Werkzeugwechsel und Stillstandszeiten. Einfache Integration in bestehende Haltersysteme Dank der ISO-Genormtheit und der trigonalen Plattenform lässt sich die Platte unkompliziert in standardisierte Halter einbauen. Die Kompatibilität hängt von Form, Freiwinkel, Toleranzklasse, Befestigung, Größe und Dicke ab, weshalb ein Blick auf diese Parameter vor der Montage Zeit spart und Fehlinvestitionen vermeidet. Der Freiwinkel beträgt 0°, was die Auswahl passender Halter erleichtert. Vielseitiger Einsatz und zielgerichtete Spanbildung Für Außen- und Innendrehen gleichermaßen geeignet, bietet der doppelseitige Spanbrecher flexible Einsatzmöglichkeiten. In Lohnfertigung und Betriebsserien erlaubt die Platte kontrollierte Spanformung und stabile Zerspanungsbedingungen. Durch die gezielte Sortenwahl lässt sich das Verhältnis von Produktivität zu Standzeit an das Werkstückmaterial anpassen. Material, Systemaufbau und praktische Vorteile Die Wendeplatte besteht aus Hartmetall mit PVD-Beschichtung und zeichnet sich durch konstante Schnittwerte aus. Zum Systemaufbau gehören die ISO-Drehplatte, ein passender Außenhalter oder eine Bohrstange, Unterlage/Klemmsatz und Ersatzschrauben, was die Beschaffung vereinfacht. Anwender erhalten so ein robustes, praxisnahes Werkzeug für produktive Bearbeitungen. Für präzise und wirtschaftliche Zerspanung empfehlen wir die WNMG 060404 AH8015 Wendeplatte von Tungaloy — bei Bedarf Beratung oder Bestellung über Metav Werkzeuge: info@metav-werkzeuge.com · +49 2822 7131930 Produktmerkmale Artikelnummer: 6966359 Hersteller: Tungaloy Serie: ISO-Drehwendeschneidplatten Bezeichnung: WNMG 060404 AH8015 SKU Hersteller: TUN6966359 Fakten Eckenradius: 0,4 mm Plattendicke: 4,76 mm Plattengröße: 06 Winkel: 80° Freiwinkel: 0° Besonderheiten Material: Hartmetall Schneidstofftyp: PVD-beschichtetes Hartmetall Sorte: AH8015 (erste Wahl für hitzebeständige Legierungen) Plattenform: Trigon Loch: mit Loch Lochstil: zylindrisches Loch Spanbrecher: doppelseitig Anwendung: Drehen Hinweis: Kompatibilität abhängig von Form, Freiwinkel, Toleranzklasse, Befestigung, Größe und Dicke FAQ Welche Werkstoffe lassen sich mit der WNMG 060404 AH8015 Wendeplatte bearbeiten? Die WNMG 060404 AH8015 Wendeplatte ist besonders geeignet für hitzebeständige Legierungen; durch die PVD-Beschichtung und Hartmetallmatrix lassen sich aber auch viele andere Stahl- und legierte Werkstoffe wirtschaftlich bearbeiten. Wie beeinflusst der Eckenradius die Bearbeitungsergebnisse? Der Eckenradius von 0,4 mm sorgt für eine präzisere Schnittkante und trägt zu einer besseren Oberflächengüte bei, gleichzeitig reduziert er Kantenausbrüche bei instabilen Spanbedingungen. Welche Bedeutung hat die Angabe Freiwinkel 0°? Ein Freiwinkel von 0° beeinflusst Auflage und Spanabführung; bei der Auswahl des passenden Halters sollte auf die Kombination von Freiwinkel und Haltergeometrie geachtet werden, um optimale Schnittbedingungen zu erzielen. Ist die Wendeplatte doppelseitig nutzbar und was bringt das? Ja, die Platte verfügt über einen doppelseitigen Spanbrecher, was die Wirtschaftlichkeit erhöht, da jede Platte länger nutzbar ist und Ausfallzeiten durch Plattenwechsel reduziert werden. Welche Artikelnummer und SKU hat das Produkt für Bestellungen? Für Bestellungen verwenden Sie die Artikelnummer 6966359 oder die Hersteller-SKU TUN6966359; die Bezeichnung lautet WNMG 060404 AH8015 und der Hersteller ist Tungaloy. Hersteller: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
WNMG 060404 AH8015 Wendeplatten - Tungaloy
WNMG 060404 AH8015 – Drehwendeschneidplatte zum Drehen von Tungaloy WNMG 060404 AH8015 ist eine ISO-genormte Drehwendeschneidplatte für Außen- und Innendrehen hitzebeständiger Legierungen Trigonplatte mit zylindrischem Loch PVD-beschichtetes Hartmetall AH8015 Doppelseitiger Spanbrecher für stabile Spanbildung ISO-kompatibel für Standardhalter Eckenradius 0,4 mm für feine Konturen Hohe Standzeit durch PVD-Beschichtung und Hartmetall Die Platte besteht aus Hartmetall mit PVD-Beschichtung und der Sorte AH8015, was eine ausgewogene Kombination aus Verschleißfestigkeit und Schneidkantenstabilität liefert. Für die Bearbeitung hitzebeständiger Legierungen bedeutet das verlängerte Werkzeugstandzeiten und konsistentere Fertigungsqualität. Der direkte Nutzen ist geringerer Werkzeugverbrauch und weniger Rüstzyklen bei gleichbleibender Oberflächengüte. Geometrie und praktische Vorteile beim Drehen Die trigonal geformte Platte bietet mehrere nutzbare Schneidkanten und eine kompakte Auflagefläche am Halter. Mit einem Eckenradius von 0,4 mm und einem Winkel von 80° ermöglicht die Geometrie präzise Konturen und kontrollierte Spanbildung. Die Kompatibilität zu Haltern richtet sich nach Form, Freiwinkel, Toleranzklasse, Befestigung, Größe und Dicke; das sorgt für verlässliche Einsetzbarkeit in vorhandenen Systemen. Einsatzempfehlung für Anwender und Fertigungsbereiche Die Wendeplatte ist erste Wahl für Generalisten in der Zerspanung, etwa im Maschinenbau, in der Automotive- und Zulieferindustrie. Durch die doppelseitigen Spanbrecher eignet sich die Platte sowohl für gleichmäßiges Schruppen als auch für stabil geführtes Schlichten, vorausgesetzt, Spanformer und Schnittwerte werden an Werkstoff und Stabilität der Aufspannung angepasst. Anwender profitieren von planbaren Werkzeugwechselintervallen und reproduzierbaren Ergebnissen. Fachbegriffe kurz erklärt und Praxis-Tipp Ein Spanbrecher sorgt dafür, dass Späne in kurze, kontrollierbare Stücke zerlegt werden, was die Oberflächengüte verbessert und das Werkzeug schont. PVD bezeichnet eine dünne, harte Schicht, die Verschleiß reduziert und Hitzebeständigkeit erhöht. Für optimale Ergebnisse empfiehlt sich das Zusammenspiel aus korrekter Schnittgeschwindigkeit, Vorschub und einem passenden Haltersystem nach ISO-Norm. Setzen Sie auf die ausgewogene AH8015-Sorte von Tungaloy für eine produktive und zuverlässige Zerspanung; für fachkundige Beratung und schnelle Lieferung kontaktieren Sie Metav Werkzeuge: info@metav-werkzeuge.com | +49 2822 7131930 Produktmerkmale Artikelnummer: 6947515 Marke: Tungaloy Serie: ISO-Drehwendeschneidplatten Ausführung: WNMG060404 Fakten Eckenradius: 0,4 mm Plattendicke: 4,76 mm Plattengröße: 06 Winkel: 80° Freiwinkel: 0° Besonderheiten Material: Hartmetall Sorte: AH8015 Beschichtung: PVD (verschleißfest) Plattenform: Trigon Loch: mit Loch (zylindrisches Loch) Spanbrecher: doppelseitig Anwendung: Drehen Schneidstofftyp: PVD-beschichtetes Hartmetall ISO-kompatibel FAQ Für welche Werkstoffe eignet sich die WNMG 060404 AH8015? Die WNMG 060404 AH8015 von Tungaloy ist für die allgemeine Bearbeitung hitzebeständiger Legierungen konzipiert und bietet eine ausgewogene Performance zwischen Verschleißfestigkeit und Schneidkantenstabilität. Wie viele nutzbare Schneidkanten hat die trigonal geformte Platte? Die Trigonform erlaubt mehrere nutzbare Schneidkanten; durch korrektes Wenden lässt sich die Lebensdauer der Wendeplatte wirtschaftlich verlängern. Passt die Platte in Standard-ISO-Halter? Die Platte ist ISO-genormt; die Kompatibilität hängt dennoch von Form, Freiwinkel, Toleranzklasse, Befestigung, Größe und Dicke des Halters ab. Was bringt die PVD-Beschichtung praktisch? Die PVD-Beschichtung reduziert Verschleiß und verbessert die Hitzebeständigkeit, was zu längeren Standzeiten und stabiler Performance bei anspruchsvollen Werkstoffen führt. Wofür ist der doppelseitige Spanbrecher geeignet? Ein doppelseitiger Spanbrecher bietet stabile Spanformung für verschiedene Bearbeitungsaufgaben und erleichtert kontrollierte Spanabfuhr sowohl beim Schruppen als auch beim Schlichten. Hersteller: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
WNMG 060404 AH8015 Wendeplatten - Tungaloy
Benefit from the combination of PVD-coated carbide AH8015, a 0.4 mm corner radius and ISO compatibility for consistent turning of heat-resistant alloys; robust chip control and a trigon form support reliable productivity. Order the WNMG060404 AH8015 insert directly via Metav Werkzeuge or consult the specialists for application advice. WNMG 060404 AH8015 — Turning insert by Tungaloy The WNMG060404 AH8015 is a trigon indexable turning insert intended for external and internal turning, offering a balanced compromise between wear resistance and cutting-edge stability for demanding alloys. PVD-coated carbide AH8015 for alloys Trigon form with 80° included angle 0.4 mm corner radius for precise contours Double-sided chipbreaker, cylindrical hole Consistent cutting performance for heat-resistant alloys The PVD-coated carbide grade AH8015 combines surface hardness and adhesion resistance to extend tool life in elevated-temperature applications. The PVD-coated carbide surface reduces flank wear while maintaining a stable edge, so cycle times stay predictable and regrinds are less frequent. This balance in material properties makes the insert particularly suitable where thermal loads and abrasive wear coincide, ensuring a measurable reduction in unscheduled tool changes and improved process reliability. Secure fit and geometry that supports accuracy Designed to ISO dimensions, the insert’s trigon outline and 80° included angle deliver a predictable engagement with standard external holders. The cylindrical hole and the 4.76 mm plate thickness contribute to a rigid clamping interface, while the double-sided chipbreaker permits indexing for extended cutting life. These geometric features reduce vibration and improve repeatability; the ISO conformity simplifies holder selection and minimises setup uncertainty across production runs. Practical handling and recommended applications For turning operations, the insert’s turning-optimised grade and 0.4 mm corner radius suit medium to finishing feeds where surface quality and dimensional control matter. Stable fixtures and correct seat geometry are recommended to exploit the indexable insert’s potential; a smoother finish is achievable with modest feeds and adequate coolant, whereas increased cutting speeds can be tested thanks to the wear-resistant coating. Technical consultation is available for parameter selection and holder matching to protect component tolerances and extend tool life. For tailored selection or to secure stock of the WNMG060404 AH8015 from Tungaloy, contact Metav Werkzeuge GmbH at +49 2822 7131930 or info@metav-werkzeuge.com for prompt advice and availability. Technical data Article number: 6966389 Manufacturer item number: TUN6966389 SKU: 6966389-Tungaloy Model series: ISO-Drehwendeschneidplatten Data Corner radius: 0.4 mm Plate thickness: 4.76 mm Included angle: 80° Relief angle: 0° Size: 06 Special features Grade: AH8015, PVD-coated Material: carbide Shape: trigon Double-sided chipbreaker Cylindrical hole Application: turning FAQ Which materials is this insert best suited for? The WNMG060404 AH8015 insert is optimised for heat-resistant alloys; the AH8015 grade offers a compromise between wear resistance and edge stability suitable for demanding alloy machining. Is the insert compatible with standard ISO holders? Yes — the insert follows ISO dimensions; compatibility depends on holder form, relief angle, tolerance class, fastening method and thickness. How is chip control achieved with this geometry? The double-sided chipbreaker and the trigon outline provide controlled chip formation and easy indexing, which supports stable cutting conditions over successive edges. What are the main recommendations for cutting parameters? Use rigid clamping and appropriate feeds for the desired surface finish; AH8015 supports elevated cutting speeds compared with uncoated grades, while coolant can improve tool life in thermally loaded applications. How many usable edges are available per insert? The indexable, double-sided design provides multiple cutting edges via rotation and indexing, extending the insert’s service life before replacement. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
WNMG 060404 AH8015 Wendeplatten - Tungaloy
Take advantage of the balanced wear resistance and edge stability of a PVD‑coated AH8015 carbide grade, combined with an economical double‑sided, reversible design for continuous turning operations; secure the WNMG060404 AH8015 from Metav Werkzeuge or ask our consultants for guidance. WNMG 060404 AH8015 — WNMG indexable insert for turning, PVD‑coated carbide, 0.4 mm radius — Tungaloy A WNMG060404 AH8015 trigon indexable insert for ISO‑standard turning, designed for external and internal turning of heat‑resistant alloys. PVD-coated carbide AH8015 for heat-resistant alloys Trigon shape with 0.4 mm corner radius Double-sided chipbreaker, reversible insert ISO-standard geometry with cylindrical hole Durable cutting performance for heat‑resistant alloys The PVD‑coated carbide grade AH8015 is optimised for a broad range of heat‑resistant alloys, delivering a balance between wear resistance and cutting edge stability. The coating reduces adhesive wear and supports higher cutting temperatures, while the substrate ensures mechanical strength. As a result, this trigon indexable insert offers consistent dimensional accuracy during demanding turning tasks and contributes to predictable process windows and fewer interrupted cycles. Predictable chip control and surface quality Equipped with a double‑sided chipbreaker, the insert provides reliable chip formation and evacuation in both roughing and finishing passes. The chipbreaker design reduces built‑up edge tendencies and helps maintain a stable cutting process, which in turn improves surface finish. For operators unfamiliar with chipbreaker terminology: a chipbreaker is a ground surface on the insert that shapes and breaks the swarf, minimising entanglement and promoting safe, continuous machining. Secure clamping and ISO interchangeability The insert follows ISO‑standard geometry so compatibility with a wide range of holders is straightforward; the appropriate holder is determined by form, clearance angle, tolerance class, fastening method, size and thickness. With a cylindrical hole and a thickness of 4.76 mm, the design facilitates secure clamping and repeatable seating in standard WNMG holders. The 0° clearance specification and an 80° edge angle contribute to robust cutting edge support, particularly in applications where side forces are significant. Cost efficiency through reversibility and grade selection Being double‑sided and reversible, the insert doubles the number of usable cutting edges per component, reducing tooling consumption and stocking complexity. Selecting the AH8015 grade for the material at hand helps extend interval lengths between indexings and replacements. When paired with a holder and feed strategy matched to the workpiece, users benefit from lower overall machining costs and improved process stability over production runs. For long‑term process reliability and consistent results, request the Tungaloy WNMG060404 AH8015 insert through Metav Werkzeuge — our specialists are available at info@metav-werkzeuge.com or by phone on +49 2822 7131930 to advise on grade and holder compatibility. Technical data Article number: 6793736 Manufacturer SKU: TUN6793736 Our SKU: 6793736-Tungaloy Model series: ISO turning indexable inserts Designation: WNMG060404 Manufacturer: Tungaloy Facts Size: 06 Thickness: 4.76 mm Corner radius: 0.4 mm Edge angle: 80° Clearance angle: 0° Hole: with hole Hole style: cylindrical hole Special features Grade: AH8015 Coating: PVD‑coated Material: carbide Shape: trigon (WNMG) Chipbreaker: double‑sided Reversible double‑sided insert for cost efficiency ISO‑standard geometry for wide holder compatibility Typical application: external and internal turning FAQ What materials is this insert suitable for? The AH8015 grade in this WNMG insert is primarily intended for heat‑resistant alloys and provides a balance between wear resistance and edge stability suitable for such materials. How many usable cutting edges does the insert provide? Thanks to its double‑sided, reversible design, the insert offers two usable cutting edges per side, effectively increasing edge count and reducing tooling consumption. Does the insert fit standard WNMG holders? Yes. The ISO designation and standardised geometry of the WNMG060404 enable interchangeability with compatible WNMG holders; correct holder selection should consider form, clearance and thickness. What is the purpose of the 0.4 mm corner radius? A 0.4 mm corner radius provides a compromise between edge strength and surface finish, helping to support the cutting edge under higher loads while producing controlled surface integrity. Is the PVD coating suitable for high‑temperature cutting? The PVD coating on the AH8015 substrate enhances resistance to adhesive wear and increases thermal stability, making it appropriate for elevated cutting temperatures encountered with heat‑resistant alloys. What should be checked before installation? Confirm holder compatibility with the WNMG060404 geometry, verify the correct clamping screw and seating, and ensure the selected chipbreaker matches the planned machining strategy. Manufacturer/Responsible: Tungaloy‑NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
WNMG 060404 AH8015 Wendeplatten - Tungaloy
Reliable wear resistance and consistent edge stability make this indexable insert a strong choice for turning heat‑resistant alloys; the trigon form and 0.4 mm corner radius support predictable surface quality and tool life. Combine the PVD‑coated carbide grade AH8015 with suitable ISO holders for efficient external and internal turning. Order the WNMG060404 AH8015 directly via Metav Werkzeuge or ask our consultants if needed. WNMG 060404 AH8015 — Indexable turning insert for turning (80°) by Tungaloy The WNMG060404 AH8015 is an ISO‑standard indexable insert designed for turning operations, optimised for heat‑resistant alloys and offering a balance between wear resistance and edge stability. ISO‑standard trigon insert PVD‑coated carbide AH8015 Corner radius 0.4 mm Double‑sided chipbreaker Reliable machining performance for heat‑resistant alloys The insert delivers stable cutting behaviour when machining demanding materials thanks to its PVD‑coated carbide grade AH8015, which is formulated to balance wear resistance with edge toughness. The trigon geometry provides three usable cutting edges per side, enabling predictable indexability and cost efficiency. As a result, cycle times are reduced and tool changes are less frequent, ensuring more continuous production and improved process economy. Easy integration into ISO turning systems Compatibility depends on holder form, relief angle, tolerance class, fastening method, size and thickness; the insert’s ISO designation WNMG060404 and 80° geometry make it compatible with a wide range of standard external holders and boring bars. The cylindrical hole and standard thickness (4.76 mm) simplify mounting and secure clamping. This technical fit reduces setup time and helps maintain concentricity and repeatability in serial production. Geometry and micro‑geometry for consistent surface finish With a corner radius of 0.4 mm and a 0° relief angle, the geometry supports a stable cutting edge that improves surface quality on both external and internal turning operations. The double‑sided chipbreaker assists chip control when machining less ductile or higher temperature alloys, reducing the risk of built‑up edge and enhancing process reliability. For finishing passes, the small radius promotes tighter dimensional control with lower cutting forces. Practical guidance for selection and use Select the chipbreaker and grade according to workpiece material, cutting strategy and machine rigidity; the grade AH8015 is a sound first choice for general turning of heat‑resistant alloys, offering a compromise between wear resistance and edge stability. When switching to roughing or heavier depths of cut, pair the insert with a more rigid clamping and appropriate feeds to exploit the insert’s durability. If uncertainty remains about the optimal configuration, technical advice is available to match the insert to the machining scenario. Contact Metav Werkzeuge for application advice, order support and availability of the WNMG060404 AH8015 insert — Metav Werkzeuge; +49 2822 7131930; info@metav-werkzeuge.com Technical data Article number: 6793741 Manufacturer SKU: TUN6793741 SKU: 6793741-Tungaloy Model series: ISO turning indexable inserts Dimensions & geometry Insert designation: WNMG060404 Size: 06 Shape: trigon (triangular) Corner radius: 0.4 mm Thickness: 4.76 mm Relief angle: 0° Hole: with cylindrical hole Chipbreaker: double‑sided Materials & applications Material: carbide (PVD‑coated) Grade: AH8015 Typical use: external and internal turning Suitable for: heat‑resistant alloys Compatibility note: ISO insert system — holder compatibility by form, clearance, tolerance class, fastening, size and thickness FAQ Is this insert suitable for finishing heat‑resistant alloys? Yes. The WNMG060404 AH8015 insert is formulated to provide a balance of wear resistance and edge stability, making it suitable for finishing passes on heat‑resistant alloys when combined with the correct cutting data. How many cutting edges are available per insert? The trigon form of this indexable insert provides multiple usable cutting edges; the WNMG060404 AH8015 design allows economical indexing to extend tool life. Which holders fit this insert? Standard ISO external holders and boring bars that accept WNMG inserts with matching size, relief angle (0° in this case), thickness (4.76 mm) and fastening style are appropriate; ensure holder tolerance and clamping match before use. What does the AH8015 grade mean in practice? AH8015 is a PVD‑coated carbide grade optimised for machining heat‑resistant alloys, offering a compromise between wear resistance and edge toughness for general turning applications. Can the insert be used for internal turning? Yes. The insert is suitable for internal turning when mounted in a compatible boring bar with sufficient rigidity and correct chip evacuation, using the WNMG060404 AH8015 geometry. Manufacturer/Responsible: Tungaloy‑NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
WNMG 060404 GT9530 Wendeplatten - Tungaloy
Take advantage of the combination of high wear resistance, consistent surface quality and straightforward holder compatibility for reliable finishing operations; order directly via Metav Werkzeuge or consult our specialists for application advice. WNMG 060404 GT9530 turning insert for turning — Tungaloy The WNMG060404 GT9530 is an ISO-format, trigon indexable insert designed for finishing and light universal turning in stable setups. Trigon 80° geometry for stable turning Coated cermet grade GT9530 for long life 0.4 mm nose radius for fine surface finish Double-sided chipbreaker, cylindrical hole Consistent surface quality and extended tool life The combination of a coated cermet cutting material and the GT9530 grade delivers a balanced wear resistance and surface finish for finishing cuts on steel. A 0.4 mm nose radius reduces scallop height while maintaining edge strength, which helps achieve consistent part appearance across batches. In practical terms, the cermet coating improves resistance to adhesive wear and maintains a stable cutting edge during steady cutting conditions, enabling longer intervals between tool changes and fewer interruptions to production. Compatibility that reduces setup time and risk Designed to ISO norms, the insert matches widely used clamping systems and insert geometries; compatibility is determined by form, relief angle, tolerance class, clamping method, size and thickness. The 80° trigon shape and 0° relief angle support robust seating in appropriate holders, and the cylindrical hole ensures precise locating when combined with the correct clamping kit and screws. Clear specification of these parameters helps avoid mix-ups and reduces setup time, which translates into measurable improvements in process stability and reduced machine downtime. Optimised for stable finishing and light universal turning With a plate thickness of 4.76 mm and a double-sided chipbreaker, the insert offers two usable cutting edges, improving cost-efficiency per edge change. The trigon shape gives a larger included angle for stable cutting in external and internal turning operations, while the coated cermet substrate prioritises surface integrity over aggressive metal removal. For shops running repeatable, rigid setups, this configuration supports predictable tool life and high-quality finishes with minimal process tuning. Contact Metav Werkzeuge today for application-specific ordering and technical guidance on Tungaloy cermet inserts; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6710248 Manufacturer SKU: TUN6710248 SKU: 6710248-Tungaloy Model series: ISO turning indexable inserts Designation: WNMG060404 GT9530 Data Size: 06 ISO code: 060404 Thickness: 4.76 mm Nose radius: 0.4 mm Relief angle: 0° Included angle: 80° Special features Coating/grade: GT9530 Cutting material: coated cermet Chipbreaker: double-sided Hole: with hole (cylindrical hole) Shape: trigon Application: turning System components: ISO insert, compatible holder, clamping kit and replacement screws FAQ Which materials is this insert suited for? The WNMG060404 GT9530 insert is optimised for steel finishing operations; the GT9530 coated cermet performs best in stable cutting conditions where surface quality and extended life are required. What is the significance of the 0.4 mm nose radius? A 0.4 mm nose radius reduces surface roughness while retaining sufficient edge strength; the 0.4 mm radius on the WNMG060404 helps achieve fine surface finish on turned components. How does the insert index and how many edges are available? The insert features a double-sided chipbreaker and is indexable; each side provides usable cutting edges, effectively doubling the number of available edges before replacement is needed. How can compatibility with holders be ensured? Match the insert form, ISO code, relief angle, tolerance class, clamping style, size and thickness to the holder specification; the WNMG060404 format and cylindrical hole facilitate precise mounting when used with the appropriate clamping kit and screws. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
WNMG 060404 GT9530 Wendeplatten - Tungaloy
Combine high surface quality and extended tool life with the GT9530-coated cermet turning insert; its stable performance under steady machining conditions reduces changeovers and supports consistent production. Order the insert directly via Metav Werkzeuge or consult our specialists for application-specific cutting data. WNMG060404 GT9530 WNMG Trigon Turning Insert by Tungaloy WNMG060404 GT9530 is an ISO-standard trigon insert designed for finishing and light general turning of steel ISO-standard trigon insert WNMG060404 Coated cermet GT9530 for fine finishing Double-sided chipbreaker, 0.4 mm radius 0° clearance angle with cylindrical hole Consistent finish and prolonged tool life for turning operations The GT9530 grade is a coated cermet engineered for fine finishing and extended duty when machining steel under stable setups. Its wear-resistant coating helps maintain a sharp cutting edge, which translates into extended tool life and fewer tool changes. For production environments where surface integrity and repeatability matter, this geometry supports predictable component quality while lowering downtime associated with regrinding or insert replacement. Reliable compatibility and secure mounting in ISO systems Designed as an ISO-standard insert in the WNMG family, the trigon shape with a cylindrical hole and defined tolerance class ensures repeatable seating in compatible holders. The listed dimensions and the 0° clearance angle provide a clear reference for selecting matching external holders or boring bars; compatibility depends on form, relief geometry, size and thickness. Clear mounting attributes reduce setup iteration and help maintain concentricity and surface consistency in serial runs. Effective chip control for stable, high-quality turning of steel The double-sided chipbreaker combined with a 0.4 mm corner radius delivers controlled chip formation during finishing and light general turning. In stable machining conditions this combination aids consistent chip evacuation and reduces rubbing on the workpiece, which benefits surface finish and process reliability. Select the GT9530 grade and appropriate chipbreaker variant according to workpiece material and machine stability to maximise performance and reduce unforeseen tool wear. Contact Metav Werkzeuge for tailored cutting data and application guidance on the WNMG060404 GT9530 insert; email info@metav-werkzeuge.com or call +49 2822 7131930 for local support Product details Article number: 6797224 Manufacturer SKU: TUN6797224 Name: WNMG060404 GT9530 Dimensions & core data Insert size: 06 ISO code: 060404 Thickness: 4.76 mm Corner radius: 0.4 mm Included angle: 80° Clearance angle: 0° Hole: cylindrical Material & special features Grade: GT9530 (coated cermet) Shape: trigon Chipbreaker: double-sided Mounting: with cylindrical hole Application: turning; finishing to light general turning of steel Series: ISO turning inserts FAQ Which materials is this insert intended for? The GT9530 grade is specified for machining steel in finishing and light universal turning applications; the WNMG060404 insert offers a balance of surface quality and wear resistance for such tasks. Is the insert indexable on both sides? Yes, the double-sided chipbreaker design provides multiple usable cutting edges and supports economical indexing of the WNMG060404 GT9530 insert. What are the key dimensions to check for holder compatibility? Check the ISO code 060404, thickness 4.76 mm, trigon form and the cylindrical hole; compatibility with a holder is determined by form, relief angle, tolerance class, size and thickness. How does the chipbreaker affect finish and stability? The double-sided chipbreaker promotes controlled chip formation and evacuation; when combined with stable machining conditions it helps achieve a consistent finish and reduces tool wear. Where to obtain recommended cutting data for this grade? Cutting parameters and application ranges for the WNMG060404 GT9530 insert can be provided by Metav Werkzeuge to match machine rigidity and workpiece characteristics Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
WNMG 060404 NS9530 Wendeplatten - Tungaloy
High-precision finishing and low cutting forces make this insert especially suitable for fine turning; the NS9530 uncoated cermet grade and a 0.4 mm corner radius deliver consistently excellent surface quality. Order the WNMG 060404 NS9530 directly via Metav Werkzeuge or ask our consultants for application advice. WNMG 060404 NS9530 WNMG turning insert for precision turning — Tungaloy A WNMG 060404 NS9530 uncoated cermet insert engineered for external and internal turning, offering a sharp cutting edge for fine finishing and stable performance in continuous cuts Uncoated cermet NS9530 for fine finishing 80° WNMG geometry for stable cutting 0.4 mm corner radius for precise profiles Double-sided, cylindrical-hole fastening Stable geometry that improves surface finish and process control The insert’s 80° geometry combined with a 0° rake angle provides a robust and predictable cutting orientation that supports repeatable profiles. The NS9530 grade is an uncoated cermet formulated for finishing operations on steel, giving a sharp cutting edge and low cutting forces. These characteristics reduce vibration at small depths of cut and make the component less sensitive to minor machine deflections, resulting in a smoother surface finish and fewer secondary operations. For customers focused on consistent part quality, the geometry and grade deliver measurable improvements in first-pass yields. Secure clamping and compatibility for reliable workshop integration Designed as an ISO-format indexable insert, the unit is supplied in a trigon form with a cylindrical hole and is double-sided, allowing economical edge indexing. Compatibility with toolholders is determined by form, clearance angle, tolerance class, fastening type, size and thickness; the system typically comprises the insert, a matching external holder or boring bar, a shim/clamp set and replacement screws. The insert’s 4.76 mm thickness and the cylindrical-hole fastening ensure secure seating and repeatable clamping, which supports process stability during cyclic production runs. Practical advantages that support efficient finishing operations The combination of a sharp cutting edge and the 0.4 mm corner radius is optimised for continuous cuts and small feed steps, helping to minimise burr formation and to achieve high-quality part faces straight from the lathe. The double-sided chipbreaker arrangement gives two usable cutting edges per index, improving cost-efficiency for finishing tasks. Selection of the chipbreaker style and the NS9530 grade should follow the targeted workpiece material and the chosen cutting parameters to maximise tool life and reduce downtime. For shops aiming to improve throughput without sacrificing surface integrity, this insert offers a balance of precision and productivity. For application advice or to order WNMG 060404 NS9530 from Metav Werkzeuge, contact our team via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6797248 Manufacturer SKU: TUN6797248 SKU: 6797248-Tungaloy Name: WNMG060404 NS9530 Tungaloy-Wendeplatte Numbers / Core technical data Corner radius: 0.4 mm Thickness: 4.76 mm Clearance angle: 0° Geometry angle: 80° Size designation: 06 Special features / Versions Uncoated cermet grade NS9530 Trigon insert form Double-sided chipbreaker With cylindrical hole (zylindrisches Loch) ISO turning insert for external and internal turning System: insert + holder + shim/clamp + screws FAQ What materials is this insert intended for? This WNMG 060404 NS9530 insert is specified as a finishing grade for steel and is best used where a sharp cutting edge and high surface quality are required. Is the insert indexable and how many edges are available? Yes, the WNMG 060404 NS9530 is double-sided with two usable cutting edges per side, providing economical indexing for finishing work. How is compatibility with toolholders determined? Compatibility depends on insert form, clearance angle, tolerance class, fastening type, size and thickness; matching a holder to the WNMG 060404 geometry and the cylindrical hole is essential for secure clamping. Can this insert achieve a high surface finish on small depths of cut? The combination of the NS9530 cermet grade and the 0.4 mm corner radius is optimised for continuous cuts and small depths of cut, producing fine surface finishes with low cutting forces. What system components are required to use this insert? A suitable ISO external holder or boring bar, an underlay/shim or clamp set and the appropriate replacement screws are required to assemble the system for the WNMG 060404 NS9530 insert. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
WNMG 060404 NS9530 Wendeplatten - Tungaloy
WNMG 060404 NS9530 WNMG060404 Tungaloy-Wendeplatte von Tungaloy – Drehen Die WNMG060404 NS9530 Tungaloy-Wendeplatte ist eine ISO-genormte Drehwendeschneidplatte für präzises Schlichten und feine Oberflächen beim Drehen. Hohe Oberflächengüte durch scharfe Schneidkante Unbeschichtetes Cermet für feines Schlichten Trigon-Form mit zylindrischem Loch für stabile Fixierung Eckenradius 0,4 mm für exakte Konturen Doppelseitiger Spanbrecher für längere Nutzungsintervalle Präzision und Oberflächenqualität steigern Die Wendeplatte liefert dank der scharfen Schneidkante und der speziell abgestimmten Sorte NS9530 eine deutlich verbesserte Oberflächengüte bei Schlichtoperationen. Durch die niedrigen Schnittkräfte eignet sich die Platte besonders für kontinuierliche Schnitte und kleine Zustellungen, wodurch Nacharbeit verringert und Zykluszeiten stabilisiert werden. Anwender profitieren von reproduzierbaren Ergebnissen bei hohen Anforderungen an Maßhaltigkeit und Finish. Schneidstoff und Werkstoffverständnis Der Schneidstoff ist ein unbeschichtetes Cermet, ein keramisch-metallischer Verbundwerkstoff, der die Vorteile von Keramik und Metall verbindet: hohe Härte, gute Wärmebeständigkeit und eine scharfe Schneidkante. Im Vergleich zu konventionellem Hartmetall verbessert Cermet die Oberflächenqualität beim Drehen von Stahl, ohne Beschichtungseffekte zu benötigen. Für Anwender bedeutet das: sauberes Schlichten mit geringeren Nachbearbeitungen. Aufbau, Kompatibilität und Spannsysteme Die Platte hat die Trigon-Form, ein zylindrisches Loch und eine Plattendicke von 4,76 mm; die Kompatibilität zum Werkzeughalter richtet sich nach Form, Freiwinkel, Toleranzklasse, Befestigungsart, Größe und Dicke. Der doppelseitige Spanbrecher erhöht die Wirtschaftlichkeit, da beide Schneiden nutzbar sind. Beim Einbau empfiehlt sich die Kontrolle der Passmaß-Toleranzen des Halters, um optimale Stabilität und Schnittbedingungen sicherzustellen. Empfohlene Anwendungen und Zielgruppe Konzipiert für das Außen- und Innendrehen, richtet sich die Wendeplatte an Lohnfertiger und Serienbetriebe, die hohe Oberflächenanforderungen bei Stahlprodukten haben. Besonders in stabilen Aufspannungen und bei geringen bis mittleren Zustellungen zeigt die Sorte NS9530 ihre Stärken. Die Kombination aus Materialwahl und Plattengeometrie reduziert Ausschuss, erhöht die Prozesssicherheit und trägt zur Kostenersparnis im Fertigungsablauf bei. Setzen Sie auf die Präzision der NS9530-Schlichtsorte von Tungaloy und optimieren Sie Ihre Dreharbeiten – Beratung und Bestellung über Metav Werkzeuge: info@metav-werkzeuge.com, Telefon +49 2822 7131930 Produktmerkmale Artikelnummer: 6735925 Hersteller: Tungaloy Serie: ISO-Drehwendeschneidplatten Bezeichnung: WNMG060404 Daten Eckenradius: 0,4 mm Plattendicke: 4,76 mm Freiwinkel: 0° Winkel: 80° Plattengröße: 06 Besonderheiten Material: Hartmetall Sorte: NS9530 (Schlichtsorte für Stahl) Schneidstoff: unbeschichtetes Cermet (keramisch-metallischer Verbundwerkstoff) Plattenform: Trigon Loch: mit Loch, zylindrisches Loch Spanbrecher: doppelseitig Anwendung: Drehen FAQ Was macht die NS9530-Sorte besonders geeignet für Schlichtarbeiten? Die NS9530-Sorte der WNMG060404 NS9530 Tungaloy-Wendeplatte bietet eine sehr scharfe Schneidkante und niedrige Schnittkräfte, wodurch beim Schlichten von Stahl hohe Oberflächengüten und geringerer Nacharbeitsaufwand erreicht werden. Kann die Wendeplatte in Standard-Außenhaltern verwendet werden? Ja, die WNMG060404 ist ISO-genormt und passt in Halter, die Form, Freiwinkel, Größe und Befestigungsart nach ISO unterstützen; bei Unsicherheit die Toleranzen des Halters prüfen. Für welche Werkstoffe ist die Platte geeignet? Die Platte ist explizit für das Schlichten von Stahl ausgelegt; das unbeschichtete Cermet optimiert dabei Oberflächengüte und Schnittverhalten. Wie viele Schneiden sind nutzbar pro Platte? Durch den doppelseitigen Spanbrecher können beide Seiten genutzt werden, wodurch die Wirtschaftlichkeit gegenüber einseitigen Ausführungen erhöht wird. Welche Informationen sind relevant für die Auswahl des richtigen Einsatzwinkels? Winkel, Freiwinkel (0°), Plattendicke und Plattenform beeinflussen die Spanbildung und Stabilität; die WNMG060404 NS9530 Tungaloy-Wendeplatte liefert im angegebenen Bereich reproduzierbare Ergebnisse. Hersteller: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
WNMG 060404 NS9530 Wendeplatten - Tungaloy
Take advantage of the combination of a sharp NS9530 uncoated cermet grade and a precise 0.4 mm corner radius for consistent finishing results; order directly via Metav Werkzeuge or consult our specialists to verify holder compatibility and optimise machining parameters. WNMG 060404 NS9530 — ISO trigon turning insert, finishing grade (Tungaloy) The WNMG 060404 NS9530 is an ISO-format trigon turning insert engineered for finishing turning operations on steel, offering a sharp cutting edge and stable chip control. ISO trigon format, size 06 NS9530 uncoated cermet finishing grade 0.4 mm corner radius for fine surface finish Double-sided chipbreaker, cylindrical hole Achieve superior surface quality with a finishing cermet grade The combination of an uncoated cermet cutting material and a fine 0.4 mm corner radius delivers low cutting forces and a sharp cutting edge, resulting in improved surface finish and reduced burr formation. As a finishing-grade solution, the insert is optimised for continuous cuts and small depth-of-cut operations, where consistent geometry and edge integrity matter. The sharp edge characteristic of this grade reduces the tendency for built-up edge and helps maintain repeatable dimensional accuracy on turned components, particularly in demanding finishing passes. Predictable clamping and straightforward system integration Manufactured to the ISO turning insert standard, the insert guarantees repeatable seating in compatible holders; compatibility depends on form, clearance angle, tolerance class, mounting and thickness. The trigon shape and cylindrical hole support stable clamping and simple indexing, while the plate thickness of 4.76 mm ensures sufficient rigidity for fine turning tasks. Clear specification of size, form and tolerance allows easy selection of a matching external holder or boring bar, reducing setup time and supporting predictable process results. Lower tool costs through indexability and controlled chip formation The insert’s double-sided chipbreaker and indexable design extend usable life per insert and reduce tooling costs through economical re-indexing. The combination of NS9530 material behaviour and the chipbreaker geometry produces manageable chips during finishing, enhancing operator safety and machine uptime. For applications that demand high surface integrity, the 0° relief and fine corner radius contribute to minimal tool pressure and consistent part appearance. The system approach — insert, suitable holder, clamp plate and screws — supports rapid replacement and consistent performance across batches. Contact Metav Werkzeuge for application-specific advice on Tungaloy finishing inserts and to confirm holder compatibility; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6966361 Manufacturer SKU: TUN6966361 Manufacturer article number: 6966361 Model series: ISO-Drehwendeschneidplatten Material: Carbide Core data Insert designation: WNMG060404 Size: 06 Thickness: 4.76 mm Corner radius: 0.4 mm Included hole: cylindrical Clearance angle: 0° Included angle: 80° Special features Grade: NS9530 (uncoated cermet) Chipbreaker: double-sided Plate form: trigon Application: Turning (finishing / external and internal) Indexable, double-sided for economical use FAQ What machining tasks is this insert best suited for? The WNMG 060404 NS9530 is a finishing insert designed for turning operations, particularly continuous cuts and small depths of cut where a sharp edge and fine surface finish are required. Is the insert compatible with standard WNMG holders? Compatibility depends on holder form, clearance angle, tolerance class, mounting and thickness; the ISO-format designation and trigon form permit use with matching WNMG-compatible external holders and boring bars when dimensions align. Can the NS9530 grade be used on hardened or interrupted materials? NS9530 is a finishing cermet grade optimised for steel in continuous cutting; it is not specified for heavy interrupted cuts or high-hardness finishing—use cases with interruptions or hard materials may require a different grade. How does the double-sided chipbreaker affect tool economy? The double-sided chipbreaker allows indexing to a fresh edge, effectively doubling the number of edges per insert and improving tool utilisation and cost efficiency for finishing tasks. Is the insert coated? The NS9530 grade on this insert is uncoated cermet, offering a sharp cutting edge and low cutting forces suited to finishing applications. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
WNMG 060404 NS9530 Wendeplatten - Tungaloy
WNMG 060404 NS9530 – Wendeplatte zum Drehen von Tungaloy Die WNMG060404 NS9530 ist eine ISO-genormte Wendeplatte für das Drehen und Schlichten von Stahl mit Schwerpunkt auf hoher Oberflächengüte und niedrigen Schnittkräften. Wendeplatte WNMG060404 NS9530 von Tungaloy Schlichtsorte für hohe Oberflächengüte Trigon-Form mit doppelseitigem Spanbrecher Zylindrisches Loch erleichtert Fixierung Unbeschichtetes Cermet, niedrige Schnittkräfte Produktivität und Prozesssicherheit steigern Die WNMG060404 NS9530 überzeugt durch ihre Schlichtsorte, die für kontinuierliche Schnitte und kleine Zustellungen optimiert ist. Durch die scharfe Schneidkante und das unbeschichtete Cermet entstehen niedrige Schnittkräfte, die die Werkzeugbelastung reduzieren und die Standzeit erhöhen. Das Ergebnis ist eine konstante Oberflächengüte bei Serienfertigung, wodurch Rüstzeiten und Nacharbeit minimiert werden. Anwender profitieren so direkt von höherer Maschinenauslastung und planbarer Fertigungsleistung. Materialeigenschaften und Bearbeitungsvorteile Das verwendete Hartmetall als Trägermaterial bietet die nötige Festigkeit für stabilen Schnitt, während das Cermet-Material feine Schnittkanten ermöglicht. Diese Kombination sorgt besonders beim Drehen von Stahl für saubere Spanbildung und reduzierte Vibrationen. Die Konstruktion mit doppelseitigem Spanbrecher unterstützt gleichmäßigen Spanfluss, was Einspanntiefe und Schnittgeschwindigkeit stabilisiert und dadurch die Produktivität steigert. Geeignet für Präzisionsschlichten und Serienfertigung Entwickelt für Anwender in Präzisionsbetrieben und Serienfertigung, liefert die Platte reproduzierbare Ergebnisse bei wiederkehrenden Bearbeitungen. Die Trigon-Form erlaubt mehrere Nutzflächen pro Plattenwechsel, was Standzeitkosten senkt und Werkzeugwechselintervalle verlängert. Kleine Zustellungen und kontinuierliche Schnitte werden zuverlässig verarbeitet, sodass sich die Platte besonders für Feinbearbeitung und Endbearbeitung von Stahl eignet. Kompatibilität, Systemaufbau und Hinweise zur Einspannung Die Plattenkompatibilität zum Halter ergibt sich aus Form, Freiwinkel, Toleranzklasse, Befestigung, Größe und Dicke. Im Systemaufbau sind ISO-Drehplatte, passender Außenhalter oder Bohrstange sowie Unterlage/Klemmsatz und Ersatzschrauben als Einheit zu betrachten. Achten Sie auf den angegebenen Freiwinkel von 0° und die Plattendicke von 4,76 mm, um optimale Sitzfestigkeit und Spanraum zu gewährleisten. Die trigonale Form mit zylindrischem Loch erlaubt einfache Fixierung und einen wiederholgenauen Sitz. Empfohlen für präzise Schlichtoperationen: WNMG060404 NS9530 von Tungaloy direkt bei Metav Werkzeuge anfragen per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 Leistungsmerkmale Artikelnummer: 6797223 Marke: Tungaloy Serie: ISO-Drehwendeschneidplatten Bezeichnung: WNMG060404 Fakten Radius: 0,4 mm Plattendicke: 4,76 mm Winkel: 80° Freiwinkel: 0° Plattengröße: 06 Eckenradius: 0,4 mm Besonderheiten Material: Hartmetall Sorte: NS9530 (Schlichtsorte für Stahl) Schneidstofftyp: unbeschichtetes Cermet Plattenform: trigon Loch: mit Loch Lochstil: zylindrisches Loch Spanbrecher: doppelseitig Anwendung: Drehen Systemaufbau: ISO-Drehplatte, Außenhalter/Bohrstange, Unterlage/Klemmsatz, Ersatzschrauben FAQ Wie unterscheidet sich die NS9530-Sorte von anderen Cermet-Sorten? Die NS9530-Sorte ist als Schlichtsorte ausgelegt und bietet gegenüber anderen Cermet-Sorten eine schärfere Schneidkante mit geringeren Schnittkräften, wodurch die Oberflächengüte beim Drehen von Stahl verbessert wird. Für welche Bearbeitungsarten ist die Wendeplatte geeignet? Die Wendeplatte eignet sich primär für Außen- und Innendrehen sowie Schlichtoperationen, insbesondere bei kontinuierlichem Schnitt und kleinen Zustellungen. Welche Vorteile bietet die Trigon-Form der Platte? Die Trigon-Form ermöglicht mehrere Nutzflächen pro Platte, reduziert Werkzeugkosten pro Bearbeitungsfläche und unterstützt einen stabilen Sitz im Halter durch das zylindrische Loch. Wie beeinflusst das unbeschichtete Cermet die Schnittbedingungen? Ein unbeschichtetes Cermet reduziert die Reibung bei Schlichtoperationen, führt zu geringeren Schnittkräften und sorgt für saubere Spanbildung, was Nacharbeit vermindert. Welche Angaben sind für die Halterauswahl entscheidend? Für die Auswahl des passenden Halters sind Form, Freiwinkel, Toleranzklasse, Befestigungsart, Größe und Dicke der Platte maßgeblich. Hersteller: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
WNMG 060404 NS9530 Wendeplatten - Tungaloy
Take advantage of the combination of uncoated cermet finishing performance, low cutting forces, and ISO compatibility for predictable turnings and excellent surface finish. Order genuine Tungaloy inserts directly via Metav Werkzeuge or consult our specialists for material-specific recommendations. WNMG 060404 NS9530 Tungaloy turning insert — finishing grade, trigon 80° WNMG060404 NS9530 Tungaloy turning insert — a trigon-shaped, ISO-standard insert engineered for finishing operations in turning, offering a sharp cutting edge and stable chip control. ISO-standard trigon geometry Uncoated cermet finishing grade Low cutting forces, high surface finish Double-sided chipbreaker Predictable finishing for steel components The WNMG060404 NS9530 insert is designed as a finishing-grade solution for turning steels where surface quality and dimensional consistency are priorities. The uncoated cermet substrate delivers a sharp, wear-resistant cutting edge that reduces built-up edge and supports continuous cutting regimes. Reduced cutting forces help to minimise vibration, so the outcome is a high surface finish and repeatable part quality, particularly on small depths of cut and light feeds. Stable geometry and efficient chip control A trigon insert with an included angle of 80° and a double-sided chipbreaker provides symmetrical performance and cost-effective indexing. The ISO conformity simplifies selection and replacement in standard holders; compatibility depends on form, clearance angle and thickness. The insert’s cylindrical hole and precise tolerances ensure secure clamping and consistent contact with the seat, supporting reliable tool life and predictable process windows. Practical integration and application support Intended for conventional and CNC turning, this insert performs best when matched with a suitable holder and light finishing parameters. The product belongs to the ISO turning insert family and is accompanied by guidance on choosing a chipbreaker and grade based on workpiece material and machining stability. For application-specific advice or suggestions on feeds, speeds and holder selection, technical support is available to help translate lab data into production-ready settings. Contact Metav Werkzeuge today to order genuine Tungaloy WNMG060404 NS9530 turning inserts and receive tailored application advice from our experts at Metav Werkzeuge: info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 6998251 SKU: 6998251-Tungaloy Manufacturer SKU: TUN6998251 Manufacturer: Tungaloy Numbers Corner radius: 0.4 mm Included angle: 80° Relief angle: 0° Thickness: 4.76 mm Size: 06 Design and application Trigon insert shape Uncoated cermet, grade NS9530 Double-sided chipbreaker Cylindrical hole Application: Turning, finishing of steel Model series: ISO turning inserts FAQ What materials is this insert optimised for? The WNMG060404 NS9530 insert is optimised for machining steel as a finishing grade; the uncoated cermet substrate promotes a sharp edge and low cutting forces when used for continuous finishing cuts. Is the insert compatible with standard ISO holders? Yes, the insert follows ISO turning insert dimensions; compatibility requires matching the holder by form, clearance angle, fixation, size and thickness to ensure correct seating and clamping. How does the chipbreaker affect performance? The double-sided chipbreaker on this trigon insert improves chip control during finishing operations and supports consistent surface quality and stable cutting forces. Can the insert be indexed to use both sides? The trigon form and double-sided design allow indexing to the next cutting edge, delivering economical use of the insert’s available cutting edges. Which SKU should be referenced when ordering? Reference the manufacturer SKU TUN6998251 or article number 6998251 when ordering the Tungaloy WNMG060404 NS9530 turning insert. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
WNMG 060404 T5105 Wendeplatten - Tungaloy
Take advantage of the T5105 CVD coating and the 0.4 mm nose radius for stable, high‑speed turning of cast iron; the trigon geometry and cylindrical hole ensure secure clamping and simple indexing. Order the insert directly via Metav Werkzeuge or consult the technical team for application advice. WNMG 060404 T5105 – ISO turning insert for high‑speed cast iron machining by Tungaloy The WNMG 060404 T5105 is an ISO‑standard trigon indexable insert designed for high‑speed external and internal turning of cast iron under stable conditions. CVD‑coated carbide for durable performance Trigon WNMG shape with 0.4 mm nose radius Double‑sided geometry with cylindrical hole 80° cutting angle, 4.76 mm plate thickness Consistent cutting performance for cast iron at high speed The T5105 CVD coating on the carbide substrate provides improved wear resistance and a stable cutting edge suitable for high‑speed machining of cast iron. A CVD coating is a ceramic layer applied at high temperature that protects the substrate against abrasion and built‑up edge; this results in longer tool life and reduced downtime for insert changes. For production settings where cycle time and repeatability matter, the coated grade reduces rework and helps to maintain a consistent surface finish over longer tool runs. Secure clamping and predictable geometry for process stability Featuring the trigon WNMG form with a cylindrical hole and 0° clearance, the insert is designed for precise seat and repeatable location in ISO‑compliant holders. The 80° cutting angle and 4.76 mm thickness contribute to mechanical stability in the tool assembly, while the 0.4 mm nose radius balances tool strength with surface finish. These geometric characteristics help to achieve predictable chip formation and reduced vibration in well‑set, rigid setups, supporting tighter tolerances and reliable component quality. Efficient edge economy and practical integration into workflows The double‑sided construction offers two indexable cutting edges, lowering the cost per edge and enabling quick rotation when wear occurs. As part of an ISO insert system, the component integrates with a wide range of external holders or boring bars provided the holder matches form, clearance, tolerance class, fixing method, size and thickness. Selecting the correct chipbreaker and grade for the workpiece stability and material is essential: the T5105 grade excels in stable cast iron turning, where optimised chip control and consistent cutting forces translate into measurable productivity gains. For robust high‑speed cast iron turning with Tungaloy’s T5105 grade, contact Metav Werkzeuge for tailored application advice and procurement: info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6853043 Manufacturer SKU: TUN6853043 SKU: 6853043-Tungaloy Model series: ISO‑Drehwendeschneidplatten Label: WNMG060404 T5105 Tungaloy‑Wendeplatte Facts Size: 06 ISO code: 060404 Nose radius: 0.4 mm Plate thickness: 4.76 mm Cutting angle: 80° Clearance angle: 0° Double‑sided: yes Special features Material: carbide Coating/grade: T5105 (CVD‑coated) Geometry: trigon (WNMG) Hole style: cylindrical hole Chipbreaker: double‑sided Application: turning (external and internal) Compatibility: ISO‑standard insert series FAQ What materials is this insert intended for? The WNMG060404 T5105 insert is developed for high‑speed machining of cast iron; the T5105 grade provides wear resistance and stable chip formation under rigid, stable conditions. Which toolholders are compatible with the insert? Compatibility depends on matching the insert form, clearance, tolerance class, fixing method, size and thickness; the trigon WNMG geometry of this insert fits ISO‑standard external holders and boring bars designed for WNMG inserts. How many usable cutting edges does the insert offer? The double‑sided design provides two indexable cutting edges per insert, enabling rotation to a fresh edge when wear appears and reducing cost per edge for the production process. Is the nose radius suitable for finishing operations? With a 0.4 mm nose radius, the insert strikes a balance between edge strength and surface finish, making it appropriate for general finishing and medium‑range turning tasks in cast iron under stable setups. What is the benefit of the T5105 coating? The T5105 CVD coating on the carbide substrate enhances abrasion resistance and chip control, extending tool life and maintaining consistent cutting performance during longer runs. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
WNMG 060404 T5115 Wendeplatten - Tungaloy
Take advantage of the combination of reliable process security, long tool life and versatile application in cast-iron turning; the CVD-coated carbide grade T5115 provides a balanced mix of wear resistance and edge stability for consistent results. Order the WNMG060404 T5115 indexable insert directly via Metav Werkzeuge or ask our consultants for application advice. WNMG 060404 T5115 – Turning insert, CVD-coated carbide for cast iron (Tungaloy) The WNMG060404 T5115 is an ISO-standard indexable turning insert intended for external and internal turning, offering a universal grade optimised for machining cast iron with stable chip control and repeatable performance. *ISO-standard WNMG insert, trigon form *CVD-coated carbide grade T5115 for cast iron *Double-sided chipbreaker for flexible use *0.4 mm corner radius, 80° insert angle Consistent productivity through tailored coating and grade The combination of a CVD-coated surface and a carbide substrate in grade T5115 delivers an optimised balance between wear resistance and edge stability, which reduces unexpected tool changes and supports steady cycle times. For operations that demand repeatable component quality, the coating reduces flank wear and helps maintain dimensional accuracy across longer runs. This makes the insert particularly suitable where a dependable compromise between life and finish is required, rather than an extreme focus on either parameter alone. Design features that simplify set-up and increase utilisation An ISO-standard trigonal insert with a cylindrical hole and double-sided chipbreaker provides straightforward compatibility with a wide range of external holders and boring bars, subject to matching form, clearance and tolerance class. The 0.4 mm corner radius and 80° insert angle offer a versatile cutting geometry that supports both finishing and medium-depth turning passes. Because the insert is double-sided, indexing is quick and inventory efficiency is improved, reducing tooling cost per component over time. Practical machining advice for better outcomes For best results in cast-iron turning select a chipbreaker and cutting data aligned with material grade and machine rigidity; the double-sided chipbreaker assists in producing short, manageable chips when combined with appropriate feeds. The trigonal shape ensures a stable seating in the pocket and good support under radial cutting forces. When tool life is critical, monitor flank wear and rotate the insert at planned intervals to exploit the full number of cutting edges. For aluminium or non-ferrous components, consider a grade optimised for lower adhesion; this insert is engineered primarily for cast-iron applications. Contact Metav Werkzeuge for individual machining recommendations or to coordinate bulk supply of Tungaloy inserts and compatible holders; Metav Werkzeuge can advise on grade selection and toolholder matching for efficient turning processes Technical data Article number: 6853044 Manufacturer SKU: TUN6853044 SKU: 6853044-Tungaloy Designation: WNMG060404 T5115 Material: Carbide Key dimensions Insert size: 06 ISO code: 060404 Thickness: 4.76 mm Corner radius: 0.4 mm Clearance angle: 0° Insert angle: 80° Features Trigon insert shape Cylindrical hole Double-sided chipbreaker CVD-coated carbide, grade T5115 Universal grade for cast iron ISO-standard indexable insert FAQ What materials is this insert best suited for? The WNMG060404 T5115 is a universal grade designed primarily for machining cast iron; the CVD-coated carbide composition supports balanced wear resistance and edge stability in such applications. Is the insert compatible with standard WNMG holders? Compatibility depends on holder form, clearance angle, tolerance class, clamping method, size and thickness; the trigonal ISO form and cylindrical hole support use with common WNMG external holders when these parameters match. How many cutting edges are available per insert? As a double-sided trigonal insert, this design provides multiple indexable edges; the exact count follows the ISO geometry and the number of usable sides per indexing cycle. What benefit does the CVD coating offer in daily production? The CVD coating enhances flank and crater wear resistance, extending service life and improving consistency in series production compared with uncoated grades. Can this insert be used for finishing and roughing operations? Yes; the 0.4 mm corner radius and 80° angle make the insert versatile for finishing and medium-depth passes, but cutting data should be adjusted according to stability and component tolerance. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
WNMG 060404 T6215 Wendeplatten - Tungaloy
WNMG 060404 T6215 – Wendeplatte zum Drehen, Tungaloy Die WNMG060404 T6215 ist eine ISO-genormte Wendeplatte für das Außen- und Innendrehen und wurde speziell für die wirtschaftliche Bearbeitung von rostfreiem Stahl unter stabilen bis leicht unterbrochenen Schnittbedingungen entwickelt. ISO-genormt für hohe Kompatibilität CVD-beschichtetes Hartmetall für Verschleißfestigkeit Doppelseitiger Spanbrecher für lange Standzeiten Trigon-Form für stabile Auflage im Halter Mit zylindrischem Loch für sichere Befestigung Präzise Standzeit für produktive Fertigung Die WNMG060404 T6215 überzeugt durch ihr CVD-beschichtetes Hartmetall, das Verschleiß reduziert und die Werkzeugstandzeit erhöht. Die gezielte Schichttechnik sorgt für bessere Wärmebeständigkeit und erlaubt stabilere Schnittbedingungen bei rostfreiem Stahl. Das Ergebnis ist weniger Werkzeugwechsel, höhere Maschinenauslastung und eine spürbare Senkung der Stückkosten. Materialverträglichkeit und Anwendungsempfehlung Für das Drehen von rostfreiem Stahl ist die Sorte T6215 ausgelegt; sie bietet eine gute Balance zwischen Zähigkeit und Härte. Bei Außen- und Innendrehprozessen empfiehlt sich die Wahl eines passenden Außenhalters mit kompatibler Form und Toleranzklasse. Die Platte eignet sich besonders, wenn konstante Oberflächengüte und reproduzierbare Bauteilmaße gefordert sind. Systemaufbau und Kompatibilitätsfaktoren erklärt Die Wendeplatte gehört zur ISO-Drehwendeschneidplatten-Familie und wird zusammen mit einem passenden Halter, Unterlage/Klemmsatz und Ersatzschrauben eingesetzt. Wichtige Kompatibilitätskriterien sind Form, Freiwinkel, Toleranzklasse, Befestigung sowie Größe und Dicke der Platte. Der Trigon-Aufbau sorgt für eine definierte Lagerung im Halter und ermöglicht doppelseitigen Einsatz. Einfache Auswahl dank technischer Kennwerte Der Eckenradius 0,4 mm bietet einen Ausgleich zwischen Schnittstabilität und Schnittkraft, die Plattendicke 4,76 mm garantiert robuste Spannung im Klemmsystem. Die Kombination aus doppelseitigem Spanbrecher und zylindrischem Loch gewährleistet sichere Befestigung und einfache Handhabung beim Wechseln. Für Anwender ohne Spezialwissen: CVD steht für chemische Gasphasenabscheidung und beschreibt eine harte, verschleißfeste Schicht auf dem Hartmetallträger. Empfehlung: Für wirtschaftliche und präzise Drehprozesse die Tungaloy Wendeplatte mit T6215-Sorte einsetzen und Verfügbarkeit bei Metav Werkzeuge anfragen unter info@metav-werkzeuge.com oder telefonisch +49 2822 7131930 Produktmerkmale Artikelnummer: 6966380 Marke: Tungaloy Serie: ISO-Drehwendeschneidplatten Bezeichnung: WNMG060404 Daten Eckenradius: 0,4 mm Plattendicke: 4,76 mm Winkel: 80° Freiwinkel: 0° Plattengröße: 06 SKU Hersteller: TUN6966380 Besonderheiten Material: Hartmetall Beschichtung: CVD (chemische Gasphasenabscheidung) Sorte: T6215 Spanbrecher: doppelseitig Loch: zylindrisches Loch Plattenform: Trigon Einsatz: Drehen (Außen- und Innendrehen) ISO-genormt (ISO-Norm für Wendeschneidplatten) FAQ Für welche Werkstoffe eignet sich die Wendeplatte am besten? Die WNMG060404 T6215 von Tungaloy ist speziell für die Bearbeitung von rostfreiem Stahl konzipiert, zeigt aber durch ihre Sorte auch gute Ergebnisse bei ähnlichen schwer zerspanbaren Werkstoffen. Ist die Platte beidseitig nutzbar und wie wirkt sich das aus? Ja, die WNMG060404 T6215 ist doppelseitig ausgelegt; das verlängert die Lebensdauer pro Platte und senkt die Teilekosten durch mehrfachen Einsatz. Welche Vorteile bietet die CVD-Beschichtung bei längerem Einsatz? Die CVD-Beschichtung verbessert die Wärmebeständigkeit und reduziert Verschleiß, was besonders bei stabilen Schnittbedingungen zu gleichbleibender Oberflächengüte und längeren Standzeiten führt. Welche Plattengeometrie sorgt für Stabilität im Halter? Die Trigon-Form bietet eine definierte Auflagefläche und erhöht die Stabilität im Halter, wodurch Vibrationen reduziert und die Prozesssicherheit gesteigert werden. für de-DE: Hersteller: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com