1000mm Digital Depth Gauge Stainless Hardened, 0.01mm Resolution, DIN 862, Supplied in Case - Metav IndustryLine

Take advantage of a robust combination of long measuring range, precise digital resolution and hardened construction for reliable depth control in large assemblies. Benefit from clear readout and process-ready data output; order the depth gauge directly via Metav Werkzeuge or consult the specialists if application advice is required.

Digital Depth Gauge M218.048 — 0–1000 mm, hardened stainless steel, DIN 862

The Digital Depth Gauge M218.048 is a heavy‑duty depth measuring instrument designed for large-format components and workshop inspection, manufactured to the requirements of DIN 862

• Digital readout with mm/inch and preset
• Measuring range up to 1000 mm
• Hardened stainless steel construction
• Data output RB 2 for process integration

Built for large components and repeatable results

Classified in the large‑range segment (500–1,000 mm), this depth gauge covers a 0–1000 mm span while maintaining the necessary profile stiffness for reproducible measurements across long runs. The substantial bridge and support geometry are intended to reduce bending and ensure consistent contact geometry over the full travel, which translates into fewer re‑measures and higher throughput when checking housings, fixtures or cast components. Compliance with DIN 862 gives a clear reference framework for fit and interchangeability in workshop and quality environments.

Fast, unambiguous digital readout that speeds decisions

The instrument provides a digital display with standard functions (ON/OFF, mm/inch, ABS/INC and ZERO/PRESET) that simplify routine checks and setup. The display resolution is 0.01 mm with the inch resolution at 0.0005 in, enabling quick detection of out‑of‑tolerance conditions without complex calculations. The ability to switch units and preset a reference position reduces setup time and helps operators make immediate, rational decisions on pass/fail criteria.

Hardened stainless construction for longevity and stability

Manufactured from hardened stainless steel, the device resists wear and corrosion in demanding shopfloor conditions. The robust material choice preserves jaw geometry and guide accuracy even under frequent use, which lowers maintenance cycles and contributes to long‑term measurement stability. Fewer servicing interventions and sustained mechanical precision reduce production interruptions and support continuous quality control.

Process integration and efficient data handling

Equipped with data output RB 2 and powered by a 3 V supply, the depth gauge is prepared for integration into inspection stations or data collection routines. Direct transfer of measured values into statistical software or logging systems eliminates manual transcription errors and shortens feedback loops between measurement and production. This rational, workflow‑centred approach improves traceability and supports lean quality processes in medium and heavy machining environments.

For specification checks, delivery details or to discuss suitability for specific components, contact Metav Werkzeuge via info@metav-werkzeuge.com or call +49 2822 7131930 to receive tailored guidance and prompt supply

Technical data

• Article number: M218.048
• GTIN: 4054469111452
• ECLASS: 21170349
• Tariff number: 90173000

Key measurements

• Measuring range: 0–1000 mm
• Measuring depth (bridge): 250 mm
• Resolution: 0.01 mm / 0.0005 in

Design and functions

• Material: hardened stainless steel
• Display: digital with ON/OFF, mm/inch, ABS/INC, ZERO/PRESET
• Data output: RB 2
• Power supply: 3 V
• Standard: DIN 862

FAQ

What measuring range does this depth gauge cover?
The Digital Depth Gauge M218.048 (Metav IndustryLine) covers a measuring range of 0–1000 mm, suitable for large components and assemblies.

What resolution and unit options are available on the display?
The instrument shows measurements at 0.01 mm resolution and 0.0005 in for imperial units, with a quick toggle between mm/inch modes.

Is the construction suitable for workshop use where corrosion may occur?
Yes, the depth gauge is made from hardened stainless steel, which provides enhanced corrosion resistance and wear protection for regular shopfloor use.

Can measurement results be exported to a logging system?
The device features data output RB 2, enabling electronic transfer of measured values into inspection or SPC systems for automated documentation.

Does the gauge conform to recognised standards for calipers and gauges?
The design and dimensions follow DIN 862, offering a recognised baseline for mechanical caliper form and function.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com