100mm Electronic Probe Capacitive Linear 0.005mm Resolution 3.2–5.2N Force, Cable Included - Microtech Metrology

High-precision capacitive digital probe with a 0–100 mm measuring range and ±0.005 mm accuracy for consistent in-line and workshop inspections; integrated 2 m cable simplifies system connection. Order the probe directly via Metav Werkzeuge or ask our consultants if integration advice is required.

Taster 120129907P — Capacitive digital probe, 0–100 mm, ±0.005 mm (Microtech Metrology)

A Taster 120129907P capacitive linear probe designed for precise dimensional verification in production, quality control and laboratory environments.

• Digital capacitive linear sensing
• Measurement range 0–100 mm
• Accuracy ±0.005 mm
• Integrated 2 m cable included

Consistent precision for traceable inspections

The probe delivers ±0.005 mm accuracy across a 0–100 mm span, providing a measurable improvement in repeatability for routine checks and incoming inspection. The combination of a fine resolution (0.0001 mm) and linear capacitive sensing means positional changes are detected with minimal hysteresis; this reduces rework and supports objective decision‑making in the measuring chain. Where documented process control is required, the stable output reduces variability between operators and fixtures.

Low and controlled measuring force to protect components

With a measuring force specified at 3.2–5.2 N, the sensor minimises the risk of part distortion during contact—important for softer materials or delicate assemblies. The standard mounting interface (shank Ø8 h6) suits common holders and adaptors, allowing secure clamping without introducing play. Because the probe’s actuation characteristics are defined, process engineers can predict contact behaviour and maintain consistent tactile interaction for repeatable measurements.

Fast integration and straightforward data handling

The unit is intended for direct electrical connection: a 2 m cable is supplied for immediate coupling to readout or data acquisition systems, enabling efficient integration into existing test rigs. The capacitive linear design produces a proportional analogue/digital signal that is well suited for automated inspection loops and SPC logging. Minimal set‑up time and standard mechanical interfaces reduce commissioning effort, increasing uptime on production lines.

Robust operation for everyday workshop use

Built for continuous measurement tasks, the probe’s straightforward construction supports reliable daily operation under typical workshop conditions. The linear sensing principle avoids complex mechanical conversions, which reduces points of wear and keeps long‑term drift low. For maintenance teams and QC staff, the device represents a practical balance of precision and durability that fits both bench testing and fixture‑mounted quality control applications.

Contact Metav Werkzeuge for expert advice on integrating the Microtech Metrology Taster 120129907P into existing measurement setups and to arrange supply from our European distribution centre

Technical data

• Article number: 120129907P
• GTIN: 4061905458217
• Brand: Microtech Metrology
• Category: Dial gauges (measurement probes)

Specifications

• Measurement range: 0–100 mm
• Accuracy: ±0.005 mm
• Resolution: 0.0001 mm
• Measuring force: 3.2–5.2 N
• Shank diameter: Ø8 h6

Features

• Capacitive linear probe
• Digital output; cable included (2 m)
• Digital operation: true
• SKU: 120129907P

FAQ

What accuracy can be expected from this probe?
The Microtech Metrology Taster 120129907P provides an accuracy of ±0.005 mm, making it suitable for standardised quality control and dimensional checks where micrometre‑level repeatability is required.

What is the measuring range and how is the output delivered?
The device covers a 0–100 mm measuring range and is supplied with a 2 m cable for direct connection to readouts or data acquisition systems; the capacitive linear sensor produces a stable measurement signal for logging.

Is the measuring force suitable for delicate parts?
Yes. The specified measuring force of 3.2–5.2 N limits deformation of machined or soft components while maintaining reliable contact for accurate detection.

How is the probe mounted in a measuring fixture?
Mounting uses a standard shank diameter of Ø8 h6, allowing secure attachment in widely used holders and adaptors without further modification.

Can this probe be used for automated inspection loops?
Its digital operation and cable connection make the probe suitable for automated inspection and SPC integration; the linear capacitive principle supports reproducible signal output for control systems.

Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools