150mm Tool Holder For Boring Bars E2 With Through Coolant, VDI40 DIN 69880 - TECWERK

Take advantage of a secure, standardised VDI40 clamping solution combined with through‑coolant capability and a design that removes the need to shorten boring bars, improving setup speed and process reliability; order the holder directly via Metav Werkzeuge or consult our specialists for integration advice.

TECWERK Tool Holder for Boring Bars E2 — VDI40, Through‑Coolant, 10 mm

The TECWERK tool holder E2 is a VDI40 clamping solution for boring bars, designed to deliver secure clamping, internal and external coolant supply and plug‑and‑play compatibility with DIN 69880 systems.

• Form E2 with VDI40 taper
• Through‑coolant, internal and external supply
• Suitable for 10 mm boring bars
• No shortening of boring bar required

Secure clamping and standardized compatibility for predictable results

The E2 configuration with VDI40 taper ensures a stable and repeatable interface with machine turrets and tool posts. Conformance to DIN 69880 provides compatibility across a wide range of toolholders and boring bar systems, reducing set‑up errors and interchange costs. The clamping geometry is engineered to maintain concentricity under cutting loads, which supports consistent run‑out values and helps protect spindle bearings. For production environments where tool change frequency and repeatability matter, this holder offers measurable gains in process control and part quality.

Faster set‑up and improved coolant performance for higher productivity

A through‑drilled design supplies internal and external coolant, optimising chip evacuation directly at the cutting edge and extending tool life by keeping working temperatures down. Because the holder is specified for use with a 10 mm boring bar in a cylindrical shank configuration, no shortening of the boring bar is required, saving preparation time and reducing handling. The combination of direct coolant feed and reduced preparatory work translates into shorter cycle interruptions and a more efficient workflow on the shop floor.

Practical benefits for workshops and production lines

The holder’s construction focuses on practical usability: a cylindrical shank, a through‑coolant bore and the E2 clamping form simplify both installation and maintenance. Operators gain from easier alignment and fewer adjustments during initial trials, while maintenance teams value the straightforward geometry when inspecting or replacing components. The design supports stable cutting conditions, making it suitable for precision boring tasks where surface finish and dimensional accuracy are required. Clear standards and proven mounting principles reduce the learning curve for new staff and support predictable outcomes over many production runs.

For tailored advice on integrating this VDI40 E2 tool holder from TECWERK into existing setups, and for swift supply from Metav Werkzeuge in Emmerich, contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 for a personalised recommendation and delivery options

Technical data

• Article number: 2000833679NW
• SKU: 2000833679NW
• Form: E2
• Product type: Tool holder for boring bars
• Manufacturer: TECWERK
• Packaging unit: 1

Facts

• d2: 10 mm
• h1: 32.5 mm
• d1: 40 mm
• d8: 55 mm
• l6: 75 mm
• l3: 22 mm
• d6: 83 mm

Special features

• Through‑drilled (yes)
• Internal and external coolant supply
• Cylindrical shank
• No boring bar shortening required
• Complies with DIN 69880
• Suitable for boring bars

FAQ

Is this holder compatible with standard VDI40 turrets?
Yes. The holder is a VDI40 E2 configuration that complies with DIN 69880 and is intended for integration with standard VDI40 turrets and tool systems.

Can coolant be delivered directly to the cutting edge?
Yes. The through‑drilled design provides internal and external coolant supply to aid chip evacuation and temperature control at the cutting zone.

Does the boring bar need to be shortened before installation?
No. The holder is designed so that no shortening of the boring bar is required, which reduces set‑up time and preparation work.

What bar diameter is this holder specified for?
The holder is specified for a 10 mm boring bar (d2 = 10 mm) and accepts a cylindrical shank for that diameter.

Which standard ensures interchangeability with other holders?
Compliance with DIN 69880 ensures standardised interfaces and interchangeability across compatible toolholders.

Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund