0-100mm Micrometer Set DIN 863/1 Hardened Spindle, Carbide Measuring Faces, 0.01mm Resolution - TECWERK

Take advantage of a workshop-ready micrometer set that pairs hardened spindle construction with carbide measuring faces for lasting accuracy; the ratchet stop and insulating sleeve support consistent readings across the full 0–100 mm range. Order directly via Metav Werkzeuge or ask the consultants for further specification details.

TECWERK Outside Micrometer Set (DIN 863/1) 0–100 mm — hardened spindle & carbide faces

A TECWERK Outside Micrometer Set designed for precise external measurement in workshop and industrial metrology, covering the complete 0–100 mm range with 0.01 mm resolution

• Hardened spindle and ground thread
• Carbide measuring faces for wear resistance
• Matt chrome reading surfaces for clear visibility
• Insulating sleeve and ratchet stop included

Consistent accuracy through hardened construction

The set is engineered for repeatable metrology: a hardened spindle combined with a ground thread maintains stable mechanical engagement, reducing wear and runout over time. The instruments offer 0.01 mm resolution, which supports fine measurement tasks while the carbide measuring faces resist abrasive wear—an advantage where frequent contact with hard surfaces would otherwise degrade accuracy. Because the micrometres conform to DIN 863/1, calibration and traceable verification remain straightforward, and the indication that the set is subject to inspection (prüfpflichtig) guides planned quality-control intervals.

Faster, more reliable measuring in daily workshop use

Built features improve throughput and reduce operator influence: the ratchet stop provides a controlled measuring force to avoid over-tightening, while the insulating sleeve reduces thermal transfer from the hand, stabilising readings in routine use. The matt chrome reading surfaces enhance contrast for quicker reading of scales. Arranged in four instruments that span the measurement steps from 0–25 mm up to 75–100 mm, the configuration plus three setting standards facilitates fast changeover and immediate deployment on the shop floor, increasing measurement efficiency without compromising traceability.

Applications, maintenance and compliance made clear

The instruments are suitable for general workshop metrology, toolmaking and inspection tasks where wear resistance and repeatable contact force matter. Maintenance is straightforward: keep the carbide measuring faces clean and free of burrs, store instruments dry, and follow routine calibration as indicated by the inspection requirement. Technical terms: the ratchet stop is a torque-limiting device that ensures the spindle is driven to a reproducible pressure; the insulating sleeve minimises heat transfer from the operator’s hand. These design choices extend usable life and reduce rework from measurement drift.

For stock availability, calibration options and expert advice on integrating TECWERK micrometres into a quality workflow, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930

Technical Data

• Article number: 2000851150NW
• Designation: Outside micrometer set (DIN 863/1) 0–100 mm
• Manufacturer: TECWERK
• Packaging unit: 1

Facts

• Measuring range: 0–100 mm
• Resolution: 0.01 mm
• Spindle diameter: 6.5 mm
• Thread pitch: 0.5 mm
• Set composition: micrometres 0–25, 25–50, 50–75, 75–100 mm; 3 setting standards
• Inspection required: yes

Special features

• Hardened spindle
• Ground thread
• Carbide measuring faces
• Matt chrome reading surfaces
• Insulating sleeve
• Ratchet stop
• Conforms to DIN 863/1

FAQ

What measurement accuracy can be expected from this micrometer set?
The TECWERK Outside Micrometer Set (SKU 2000851150NW) provides a resolution of 0.01 mm; combined with the hardened spindle and carbide faces, this supports stable, repeatable accuracy when the instruments are maintained and periodically verified.

How does the ratchet stop improve measurement consistency?
The ratchet stop limits the torque applied during measurement, ensuring a reproducible contact force; in the TECWERK micrometres this reduces operator-induced variation and helps achieve comparable readings across different users.

Is calibration or inspection required for the set?
Yes — the set is marked as subject to inspection (prüfpflichtig). Regular verification and calibration are recommended to maintain traceability and conformity with quality systems when using the TECWERK micrometres.

Which materials are the measuring faces suitable for?
The carbide measuring faces are designed for wear resistance and are appropriate for general metal workshop use; they extend service life when measuring steel and similar materials under standard inspection conditions.

What maintenance is recommended to prolong service life?
Keep measuring faces clean and free of debris, avoid impact, store the instruments in a dry case, and perform regular calibration checks. These practices preserve the hardened spindle and the accuracy of the set.

Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund