300mm Height Gauge And Scriber Digital 0.01mm / 0.0005in IP65 - TECWERK

Take advantage of the combination of high-resolution measurement, a robust ground base and a capacitive sensor system for faster, economical layout and inspection tasks; order directly via Metav Werkzeuge or contact our consultants for technical advice.

TECWERK Height Gauge and Scribing Instrument – 300 mm, digital 0.01 mm

A TECWERK Height Gauge and Scribing Instrument for precise height measurement and layout work in workshop and production environments.

• Digital 5-digit LCD display
• Resolution 0.01 mm / 0.0005 in
• Robust base with ground bearing surface
• Capacitive measuring system for fast traverse

High-resolution measurement for dependable results

The instrument provides a resolution of 0.01 mm (0.0005 in) together with a 5-digit LCD display, enabling clear readouts of very small increments. This level of detail supports repeatable height checks and dimensional layout, reducing uncertainty during inspection and setup. The ability to select the measurement direction and to set zero in any position minimises additional calculation steps and streamlines process documentation. Such measurable precision is especially beneficial where tolerances are tight and traceable data is required.

Workshop-ready construction that speeds up routines

A robust base with a ground bearing surface gives the device a stable reference, improving repeatability during scribing and measuring operations. The built-in hand crank facilitates controlled vertical traverses, while the HM scribing needle delivers a durable marking point for layout work. The combination of stable support and mechanical control reduces rework and supports a more efficient workflow on the shop floor, as short cycle times and reliable marks cut down adjustment loops.

Fast, economical measuring thanks to capacitive sensing

The capacitive measuring system used in this instrument allows comparatively high traverse speeds without sacrificing measurement reliability. Capacitive sensors detect positional changes through variations in capacitance, which permits quick, continuous measurement feedback rather than stepwise readings. The result is a balance between speed and accuracy that makes the instrument suitable for regular production checks and frequent layout tasks, keeping throughput consistent while maintaining measurement integrity.

Compliance and inspection readiness for quality assurance

The device is specified as inspection required, reflecting suitability for regulated or audited environments where instruments must undergo verification. The 300 mm measuring range covers a broad set of common height-checking tasks and layout operations across assemblies and components. As a precision layout tool from a recognised brand, the instrument supports documented quality processes and helps maintain consistent production standards over time.

For ordering, calibration queries or tailored advice on integrating the TECWERK height gauge into production, contact Metav Werkzeuge — info@metav-werkzeuge.com or +49 2822 7131930 — our consultants will assist with technical details and supply options

Technical data

• Article number: 2000851591NW
• Product: Height gauge and scribing instrument
• Brand: TECWERK
• Measuring range: 300 mm
• Resolution: 0.01 mm / 0.0005 inch
• Display: 5-digit LCD
• UID: 2000851591NW

Facts

• Measuring range: 300 mm
• Resolution: 0.01 mm / 0.0005 inch
• Display digits: 5

Special features

• digital
• robust base with ground bearing surface
• 5‑digit LCD display
• measurement selection in both directions
• zero in any position
• hand crank
• HM‑tipped scribing needle
• capacitive measuring system enables high traverse speeds
• inspection required

FAQ

What measuring range does the instrument cover?
The TECWERK height gauge and scribing instrument covers a 300 mm measuring range suitable for most workshop and production layout tasks.

What is the display resolution and unit options?
The device provides a 0.01 mm (0.0005 inch) resolution on a 5‑digit LCD, with clear indication for fine measurement work.

Can the instrument mark components as well as measure them?
Yes, the HM‑tipped scribing needle is fitted for layout marking while the instrument simultaneously records height values.

Is the instrument suitable for high-speed measurement cycles?
The capacitive measuring system of the instrument is designed to allow high traverse speeds while maintaining reliable measurement feedback.

Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund