Skip to main content Skip to search Skip to main navigation
Cheap Shipping Cost
fast shipment
Advice before purchase
Purchase comfortable on account
Hotline +49 2822 7131930

250mm x 160mm Fabrication Angle Plate Without Stop, 25x5mm Cross-Section - TECWERK

Product information "250mm x 160mm Fabrication Angle Plate Without Stop, 25x5mm Cross-Section - TECWERK"

Take advantage of the clear geometry and stable cross‑section for repeatable right‑angle checks; the compact L‑leg dimensions make setup quick and measurement errors less likely. Order the L‑shaped engineer's square directly via Metav Werkzeuge or consult our team if specification advice is needed.

L-shaped engineer's square 250 x 160 mm (without fence) — TECWERK

An L‑shaped engineer's square 250 x 160 mm designed for workshop layout and right‑angle verification in metalworking, supplied without a stop for flexible positioning

  • L-shaped design for two‑leg checks
  • Cross-section 25 x 5 mm
  • Suited for general metalworking checks
  • Supplied without stop for flexible use

Consistent right‑angle reference for routine workflows

The L‑shaped geometry with legs of 250 x 160 mm provides a stable, repeatable datum for layout and inspection tasks. Where a defined right angle is required, this tool serves as a dependable reference; the modest leg lengths allow access into tighter assemblies where larger squares would be unwieldy. The 25 x 5 mm cross‑section contributes to a straight edge that resists twist under normal handling, reducing setup time and supporting efficient process flows in small fabrication and maintenance environments.

Reduced handling and faster verification with stable geometry

A compact cross‑section combined with the L‑form minimises the need for frequent re‑alignment during batch checks. The tool's geometry is aimed at straightforward dimensional control: measuring faces and marking lines can be completed more quickly because the square sits flat and maintains its angle during strokes. This results in fewer interruptions for re‑fixturing and a measurable gain in throughput for repetitive layout and basic inspection tasks.

Flexible design for varied workshop applications

Being supplied without fence allows unrestricted placement against irregular workpieces and inside fixtures where a fixed stop would interfere. The absence of a stop increases adaptability when checking assemblies, blocks or fabricated frames, and makes the tool suitable for tasks that require freehand marking or comparative checks. For users moving between layout, marking and inspection, that flexibility supports smoother workflows and a simpler tool set on the bench.

Clear specification to simplify selection and stock control

With a concise set of measurable features — leg dimensions and a defined 25 x 5 mm cross‑section — the square is straightforward to specify and reorder. The single‑unit packaging supports targeted replenishment for individual workstations or maintenance kits. Where purchasers require unambiguous technical data for procurement, these values enable quick assessment of suitability against existing gauges and inspection routines without the need for time‑consuming clarification.

For reliable right‑angle checks, order the TECWERK L‑shaped engineer's square from Metav Werkzeuge or contact our consultants at info@metav-werkzeuge.com or +49 2822 7131930 for specification support and delivery options

Technical Data

  • Article number: 2000858025NW
  • Description: L-shaped engineer's square 250 x 160 mm (without fence)
  • Product type: Schlosserwinkel / engineer's square
  • Manufacturer: TECWERK
  • UID: 2000858025NW

Facts

  • Cross-section: 25 x 5 mm
  • Leg dimensions: 250 x 160 mm
  • Packaging unit: 1

Special features

  • Execution: supplied without stop (ohne Anschlag)
  • Compact L‑leg design
  • Suitable for layout and right‑angle verification

FAQ

What applications is this square best suited for?
The L‑shaped engineer's square is intended for layout, marking and right‑angle verification in general metalworking and small assembly tasks; its compact leg lengths make it useful where larger squares obstruct access.

Can the square be used for precision inspection tasks?
The square offers a stable reference thanks to the 25 x 5 mm cross‑section, but for high‑precision metrology applications a calibrated precision gauge is recommended; use the TECWERK engineer's square for routine checks and layout.

What does 'without fence' mean in practice?
'Without fence' indicates the tool is supplied without a fixed stop or heel, allowing the square to be positioned freely against irregular workpieces or inside fixtures for flexible marking and checking.

Is the square suitable for marking on assembled components?
Yes, the L‑leg geometry and moderate leg lengths make it suitable for comparative checks and freehand marking on assemblies where a fixed stop would be impractical.

How should the square be stored to retain accuracy?
Store the square flat or hung by a non‑bearing point to avoid bending; the compact cross‑section is robust for workshop use but benefits from careful storage to maintain a straight reference edge.


Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund