75x50mm Angle Gauge With Stop, 15 x 5 mm Cross-Section - TECWERK

Benefit from a compact, DIN 875/I‑compliant layout tool with legs 75 x 50 mm and an integrated stop for repeatable positioning; the combination of standardised accuracy and robust cross‑section supports faster set‑up and consistent results. Order the item directly via Metav Werkzeuge or consult our advisers for application guidance.

TECWERK engineer's square DIN 875/I — legs 75 x 50 mm with stop

A TECWERK engineer's square DIN 875/I designed for reliable squareness checks and repeatable layout tasks in metalworking and general workshop use

• DIN 875/I compliance
• Legs 75 x 50 mm
• Cross-section 15 x 5 mm
• Built-in stop for repeat measurements

Accurate standard compliance for repeatable layout work

The DIN 875/I classification confirms that this engineer’s square is manufactured to a recognised accuracy grade, making it suitable where precise right‑angle checks are required. The geometry, combined with a cross‑section of 15 x 5 mm, delivers stiffness and reduces flex during alignment and marking operations. This results in fewer re‑set cycles and a smoother workflow on benches and machines. Where measurement standards matter, the presence of a defined DIN grade simplifies quality documentation and process control.

Compact dimensions that speed up setup and handling

With legs 75 x 50 mm, the tool keeps a small footprint while retaining practical reach for fixtures and small assemblies. The compact frame eases handling and storage, and the integrated stop allows users to place the square against a reference edge for repeatable positioning without additional clamps. The result is reduced set‑up time and higher throughput for routine squareness inspections or layout tasks, which is particularly valuable in busy workshops and trade counters.

Confidence through brand standards and distribution clarity

Produced under the TECWERK designation, this square offers a straightforward, no‑frills solution for everyday squareness verification. Distribution via Metav strengthens buying confidence: Metav acts as a quality filter for the European market, combining decades of trade experience with a wide product range and transparent logistics. If further technical data or application advice is required, Metav’s team is available to supply clarification and ensure the item matches the intended use.

For technical recommendations or to secure the TECWERK engineer's square (SKU 2000858435NW), contact Metav Werkzeuge for ordering and application support: info@metav-werkzeuge.com, +49 2822 7131930

Technical data

• Article number: 2000858435NW
• Label: Winkel DIN 875/I Schenkel-L.75x50mm m.Anschlag TECWERK
• Product type: Engineer's square
• Execution: with stop

Facts

• Leg lengths: 75 x 50 mm
• Cross-section: 15 x 5 mm
• Packaging unit: 1
• UID: 2000858435NW

Special features

• DIN 875/I compliance
• Built-in stop for repeat measurements
• Manufacturer: TECWERK

FAQ

What accuracy standard does this square meet? The TECWERK engineer's square conforms to the DIN 875/I standard, indicating manufacture to a recognised accuracy grade for right‑angle verification.

Is the stop useful for repeatable checks? Yes, the supplied stop provides a fixed reference face for repeatable positioning, enabling consistent layout and marking operations without extra fixtures.

Are the dimensions suitable for small assemblies and fixtures? The compact leg dimensions of 75 x 50 mm make the square well suited to small assemblies, jig work and close‑quarters layout tasks in workshops.

What does the cross‑section mean for handling and rigidity? A cross‑section of 15 x 5 mm increases rigidity compared with thinner profiles, reducing flex during use and improving the reliability of squareness checks.

Can the square be traced back to a specific item or batch? The SKU 2000858435NW and UID 2000858435NW provide identification for ordering and stock control of this TECWERK engineer's square

Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund