1.6mm Centre Drill DIN 333 Form A 60° Countersink Angle HSS, For General Use - TECWERK

Reliable centre-drilling for consistent starts: the HSS DIN 333 Form A centre drill combines a 60° countersink with a 1.6 mm pilot to produce DIN‑332-compliant centre holes without additional protective countersinking; the right‑hand design and a recommended feed of 0.02 mm/rev in steel up to 800 N ensure repeatable performance. Order directly via Metav Werkzeuge or request specialist advice for application-specific guidance.

Centre drill DIN 333 Form A — 1.6 mm HSS, 60° (TECWERK)

The Centre drill DIN 333 Form A is a high‑speed steel centre‑drilling tool designed to create precise centre holes to DIN‑332 standards, featuring a 60° countersink for reliable lathe and drilling starts.

• HSS for wear resistance
• 60° countersink angle for DIN 332 centres
• 1.6 mm pilot diameter for precise starts
• Recommended feed 0.02 mm/rev in steel

Accuracy where it matters: consistent centre holes for reliable machining

A compact centre‑drilling tool delivers the first, crucial machining step by producing accurately positioned centre holes, reducing run‑out and improving subsequent turning or drilling operations. Constructed from HSS, this tool maintains cutting geometry under typical workshop conditions, while the 60° countersink conforms to the DIN specification to ensure compatibility with standard centres and fixtures. The small 1.6 mm pilot provides a precise start even on small parts, helping to avoid wandering and reducing the need for rework. The combination of standardised geometry and hardened material translates directly into improved process stability and fewer rejected parts.

Designed for efficient cycle times and dependable feeds

Built as a Form A centre drill with a right‑hand cutting orientation, the tool supports straightforward feed management on production equipment. The documented feed of 0.02 mm/rev in steel up to 800 N gives a practical operating point for setting machine parameters and estimating cycle times. This clear numeric guidance enables planners and operators to balance throughput with tool life, yielding faster set‑up and predictable machining results. The right‑hand configuration is compatible with conventional spindles and collets, keeping integration with existing toolsets simple and cost‑effective.

Practical workshop handling and broad usability

Compact and robust, the tool is intended for general‑purpose centre‑drilling tasks where repeatability matters. The DIN 333 standard geometry means the centre‑drilled holes match downstream tooling expectations, reducing alignment issues during turning or drilling. The tool is supplied in a small pack for easy storage and quick replacement in busy workshop environments. With its HSS construction and standard form, the centre‑drilling tool offers a balance of precision and reliability suitable for both jobbing shops and production lines that demand consistent starts without additional protective countersinking.

For dependable centre‑drilling using TECWERK tooling, contact Metav Werkzeuge for ordering and application support — Metav Werkzeuge can advise on integration and supply from stock.

Technical data

• Article number: 2000861804NW
• Item: Centre drill DIN 333 Form A, 1.6 mm, HSS, right‑hand, TECWERK
• Packaging unit: 5

Facts

• Diameter: 1.6 mm
• Countersink angle: 60°
• Recommended feed in steel up to 800 N: 0.02 mm/rev
• Standard: DIN 333 / produces DIN 332 centre holes

Special features

• Material: HSS
• Design: Form A
• Cutting direction: right‑hand
• Application: manufacture of centre holes per DIN 332 without protective countersink
• General‑purpose centre‑drilling use

FAQ

What is the primary purpose of this centre drill?
The centre drill is intended for manufacture of centre holes to DIN‑332 standard, providing an accurate start for subsequent drilling or turning operations.

Which material and diameter specifications apply to this tool?
This TECWERK centre drill is made from HSS with a 1.6 mm pilot and a 60° countersink angle suited to standard centre fittings.

What feed and machine settings are recommended?
A feed of 0.02 mm/rev is recommended in steel up to 800 N; this provides a reliable balance between cutting action and tool life.

How is the tool supplied and what is its design form?
The centre drill is supplied in a pack of five and is manufactured to Form A with right‑hand cutting direction.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com