1.6mm Centre Drill DIN 333 Form A, HSS-Co Extra Long, 60° Countersink Angle, Right-Hand - TECWERK

Combining HSS‑Co durability with DIN 333 conformity and an extra‑long reach ensures precise, repeatable centre holes in standard workshop and production settings; benefit from a 60° spotting angle and a defined feed rate for steel up to 800 N. Order the centre drill directly via Metav Werkzeuge or consult our product specialists for machining guidance

TECWERK centre drill DIN 333 Form A — HSS‑Co, 1.6 mm, extra‑long, 60°

The TECWERK centre drill DIN 333 Form A is an extra‑long, right‑hand HSS‑Co tool designed for producing accurate centre holes for turning, drilling preparation and general machining

• HSS‑Co material for high wear resistance
• Conforms to DIN 333 Form A
• 60° centre/spotting angle
• Extra‑long geometry for deep reach

Reliable centring for consistent assembly accuracy

A centre drill that meets DIN 333 enables dependable alignment of workpieces before main drilling or turning operations. The 60° spotting angle produces a defined and repeatable centre hole, which reduces runout and improves chucking accuracy. For workshops that demand predictable positioning and reduced rework, the controlled chamfer from this tool ensures parts enter subsequent machining with consistent orientation and minimal setup variation

High‑performance material and defined machining data

Constructed from HSS‑Co, the tip offers enhanced wear resistance and thermal stability compared with standard high‑speed steels, helping to extend tool life under frequent use. The tool’s right‑hand cutting geometry supports conventional lathe and drilling spindle directions, while the specified feed of 0.02 mm/rev in steel up to 800 N gives a clear machining parameter for process planning. These measurable values support productivity forecasting and reduce guesswork when integrating the tool into production cycles

Extra‑long design for hard‑to‑reach operations

The extra‑long shank and body geometry permit centring of deeper or recessed bores without compromising stability. This extended reach is particularly useful when preparing long bars, stepped shafts or workpieces with restricted access, avoiding the need for additional fixturing or secondary operations. The design balances reach with rigidity to retain precision while accessing areas that standard lengths cannot comfortably serve

Improved process reliability and easier part transfer

Standard conformity and defined cutting data simplify tool selection and quality control. Using a centre drill that adheres to established norms reduces variability across batches and supports tighter tolerances in the finished product. The tool’s construction and specifications make it straightforward to document process parameters in work instructions and to achieve repeatable results across shifts, contributing to overall shopfloor efficiency and reduced scrap rates

Contact Metav Werkzeuge for tailored technical advice and to order the TECWERK centre drill for reliable centring and extended reach

Technical data

• Article number: 2000861977NW
• Label: Zentrierbohrer DIN 333 Form A D.1,6mm HSS‑Co re.ü.-lang TECWERK

Facts

• Diameter: 1.6 mm
• Centre angle: 60°
• Feed in steel up to 800 N: 0.02 mm/rev
• Packaging unit: 1

Special features

• Material: HSS‑Co
• Standard: DIN 333, Form A
• Cutting direction: right‑hand
• Length: extra‑long
• Application: production of centre holes per DIN 332 without pilot countersink

FAQ

What is the primary application of this centre drill?
The TECWERK centre drill DIN 333 Form A is intended for creating precise centre holes as preparation for turning and drilling operations, ensuring accurate workpiece alignment

Which materials can be machined with this tool?
The centre drill is suitable for general machining tasks and is specified to operate with a feed of 0.02 mm/rev in steel up to 800 N; its HSS‑Co composition provides wear resistance for repeated use

How does the extra‑long version benefit workshop processes?
Extra‑long geometry enables access to recessed or deep features without additional tooling or setups, improving workflow efficiency and reducing handling time

Is the tool compliant with industry standards?
Yes, the tool conforms to DIN 333 (Form A) and is intended for producing centre holes in accordance with DIN 332 without a pilot countersink

What cutting direction does the tool use?
The centre drill features a right‑hand cutting geometry suitable for standard lathe and drill spindle rotation

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com