14mm Slot Drill DIN 6527K Type N Solid Carbide TiAlN Coated, 2 Flute Short, DIN 6535 HB - TECWERK

High-performance solid carbide construction combined with a TiAlN coating and a short, low‑vibration geometry delivers durable performance for both roughing and finishing in steels and non‑ferrous alloys. Order the slot milling cutter directly via Metav Werkzeuge or ask our consultants if needed.

Slot milling cutter DIN 6527 K Type N, Ø14 mm, solid carbide, TiAlN – TECWERK

The Slot milling cutter DIN 6527 K Type N (Ø14 mm) is a short, two‑flute solid carbide cutter with TiAlN coating, engineered for low‑vibration slotting, plunge operations and reliable finishing across a wide range of materials.

• Solid carbide with TiAlN coating
• Two‑flute centre‑cut geometry
• Cylindrical shank to DIN 6535 HB
• Low‑vibration short design for finishing

Consistent wear resistance and longer tool life for mixed materials

The combination of solid carbide substrate and TiAlN coating provides a heat‑resistant, wear‑protective surface that supports elevated cutting parameters while maintaining edge integrity. This means fewer tool changes and more productive cutting time when machining stainless steel, alloyed steels, cast iron and non‑ferrous alloys. The coating reduces adhesion and thermal softening, so the cutter retains form and finish quality over longer production runs.

Geometry that reduces chatter and enables plunge cutting

A two‑flute, centre cut design with dynamic helix and a 45° protection chamfer allows controlled chip evacuation and stable slotting even in interrupted cuts. The tool’s neck relief and short overall form improve rigidity at the cutting zone, minimising vibration during aggressive passes. These characteristics make the cutter suitable for both roughing and finishing, delivering reliable surface results and dimensional stability in keyway and slot operations.

Standards, shank interface and workshop integration

Manufactured to DIN 6527 K with a cylindrical shank in accordance with DIN 6535 HB, the tool features a shank tolerance of h6 and an effective length engineered for typical holder systems. The small protection chamfer (0.2 mm) and the precise Ø14 mm shank simplify gripping and repeatability in tool holders, reducing setup time and supporting consistent, repeatable results on series workpieces.

Contact Metav Werkzeuge today to discuss tool holders and machining strategies for this TECWERK slot milling cutter – Metav Werkzeuge can advise on suitable feeds and speeds and supply the item directly from Emmerich.

Technical data

• SKU: 2000866165NW
• Standard: DIN 6527
• Material: solid carbide
• Coating: TiAlN
• Type: slot milling cutter (Type N)

Facts

• Diameter: Ø14 mm
• Overall length: 75 mm
• Effective length: 28 mm
• Cutting length: 2 mm
• Free relief: 13.5 mm
• Number of flutes: 2

Special features

• Centre cut for plunge capability
• Cylindrical shank to DIN 6535 HB
• Shank tolerance h6
• Right‑hand cutting
• 45° protection chamfer 0.2 mm
• Short, low‑vibration design
• Suitable for steel, cast iron, Cr‑Ni steels, non‑ferrous metals, aluminium with silicon and abrasive materials

FAQ

What materials is this cutter suitable for?
The TECWERK slot milling cutter (DIN 6527 K Type N, SKU 2000866165NW) is designed for very good performance in steel, cast iron, stainless (Cr‑Ni) steels, non‑ferrous metals and aluminium alloys with silicon content, as well as many abrasive materials.

Can the tool perform plunge cuts?
Yes; the centre‑cut geometry and two‑flute design enable plunge cutting and slotting operations, which makes the cutter versatile for keyway and slot machining.

How does the TiAlN coating benefit machining?
The TiAlN coating increases heat resistance and reduces tool wear on the TECWERK cutter, permitting higher cutting parameters and longer tool life compared with uncoated carbide tools.

Is this cutter suitable for finishing as well as roughing?
The short, rigid geometry and dynamic helix of this milling cutter make it appropriate for both roughing and finishing tasks, providing stable cutting and good surface quality in the same tool.

What shank and holder standards apply?
The tool has a cylindrical shank to DIN 6535 HB with h6 tolerance and a nominal shank diameter of 14 mm, ensuring compatibility with standard collets and holders.

Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund