6mm Slot Drill DIN 6527K Type N, Solid Carbide TiAlN-Coated, 3 Flute Short 54mm, 5.8mm Relief - TECWERK

Benefit from the TiAlN‑coated solid carbide construction combined with a three‑flute, centre‑cut geometry for vibration‑reduced slotting and reliable roughing and finishing. Order directly via Metav Werkzeuge or consult our specialists for application advice.

TECWERK slot milling cutter DIN 6527 K – Ø6 mm, VHM TiAlN-coated

A TECWERK slot milling cutter DIN 6527 K designed as a short, rigid three‑flute tool for precise slotting and clean entry cuts in a wide range of metals

• TiAlN-coated solid carbide
• 3-flute geometry with centre cutting
• Short version for high rigidity
• Suitable for steel, stainless and cast iron

High performance through coating and carbide substrate

The combination of solid carbide (fine-grain) substrate and a durable TiAlN coating provides elevated heat resistance and extended tool life when machining demanding materials. The tool’s three‑flute design with a centre cut enables reliable axial entry and clean slot starts, while the short overall length boosts stiffness for reduced deflection. These characteristics allow efficient removal rates during both roughing and finishing operations, resulting in consistent component quality and fewer rework cycles.

Precise dimensions and geometry for stable machining

With a nominal diameter of 6 mm, a cutting length of 3 mm and an effective length of 16 mm, the short body ensures high rigidity and process stability. The cutter is supplied with a 6 mm cylindrical shank to DIN 6535 HB and a shank tolerance of h6, providing secure clamping and concentricity in standard toolholders. The unequal helix and neck relief reduce harmonic excitation, promoting vibration‑reduced machining and predictable surface finishes even at higher feed rates.

Broad material suitability and practical applications

The geometry and coating make this cutter universally applicable for machining steel, stainless steel (INOX), cast iron, alloyed steels and a range of non‑ferrous metals, including aluminium alloys with silicon content and abrasive materials. The tool is suitable for both roughing and finishing, and the short, rigid format is especially beneficial where tool deflection must be minimised. The integrated 45° protection chamfer and the finely tuned cutting edges contribute to stable chip formation and a low tendency to build‑up on the cutting edges.

For tailored application advice on the TECWERK slot milling cutter and reliable supply from Metav Werkzeuge, contact Metav Werkzeuge GmbH in Emmerich at info@metav-werkzeuge.com or by phone on +49 2822 7131930 to discuss clamping options and batch availability

Technical Data

• Article number: 2000866245NW
• Label: Bohrnutenfräser DIN 6527K Typ N D.6mm VHM TiAlN HB Z.3 kurz TECWERK
• Standard: DIN 6527
• Brand: TECWERK

Facts

• Diameter: 6 mm
• Shank diameter: 6 mm
• Overall length: 54 mm
• Cutting length: 3 mm
• Effective length: 16 mm
• Free relief: 5.8 mm
• Number of flutes: 3
• Cutting direction: right-hand
• Shank tolerance: h6
• Protection chamfer: 0.12 mm

Special features

• Material: solid carbide (fine-grain)
• Coating: TiAlN
• Type: DIN 6527 K, Type N
• Centre cutting for axial entry
• Unequal helix for vibration reduction
• Neck relief grind
• Cylindrical shank to DIN 6535 HB
• Short design for increased rigidity
• Suitable for roughing and finishing
• Very good suitability for steel, INOX, castings, non‑ferrous metals and special alloys

FAQ

Can this slot milling cutter be used for plunge cuts?
The TECWERK slot milling cutter features a centre cut, allowing limited axial entry and controlled plunging for slot starts; full plunge operations should be planned according to machine and clamping rigidity.

Which materials are best machined with this cutter?
The cutter is optimised for steel, stainless steel (INOX), cast iron, alloyed steels and non‑ferrous metals, and performs well with aluminium alloys containing silicon and abrasive materials.

What is the shank size and clamping requirement?
The tool has a 6 mm cylindrical shank with h6 tolerance, designed for secure clamping in standard DIN 6535 HB toolholders and collets.

Does the TiAlN coating improve tool life for high-temperature applications?
Yes, the TiAlN coating on the solid carbide substrate reduces thermal load on the cutting edges and extends tool life in elevated temperature and high‑speed conditions.

What is the article number for ordering and traceability?
Order reference: 2000866245NW, which identifies the TECWERK slot milling cutter DIN 6527 K, Ø6 mm, VHM TiAlN

Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund